This is essentially a revert of:
e3f72b749d pinctrl: cherryview: fix Strago DMI workaround
86c5dd6860 pinctrl: cherryview: limit Strago DMI workarounds to version 1.0
because even with 1.1 versions of BIOS there are some pins that are
configured as interrupts but not claimed by any driver, and they
sometimes fire up and result in interrupt storms that cause touchpad
stop functioning and other issues.
Given that we are unlikely to qualify another firmware version for a
while it is better to keep the workaround active on all Strago boards.
Reported-by: Alex Levin <levinale@chromium.org>
Fixes: 86c5dd6860 ("pinctrl: cherryview: limit Strago DMI workarounds to version 1.0")
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Alex Levin <levinale@chromium.org>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Keeping the IRQ chip definition static shares it with multiple instances of
the GPIO chip in the system. This is bad and now we get this warning from
GPIO library:
"detected irqchip that is shared with multiple gpiochips: please fix the driver."
Hence, move the IRQ chip definition from being driver static into the struct
intel_pinctrl. So a unique IRQ chip is used for each GPIO chip instance.
Fixes: ee1a6ca43d ("pinctrl: intel: Add Intel Broxton pin controller support")
Depends-on: 5ff56b015e ("pinctrl: intel: Disable GPIO pin interrupts in suspend")
Reported-by: Federico Ricchiuto <fed.ricchiuto@gmail.com>
Suggested-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
cycle:
Core changes:
- Fix errors in example code in the documentation.
New drivers:
- Add support for JZ4760, JZ4760B, X1000, X1000E and X1500 to
the Ingenic driver.
- Support Cirrus Logic Madera CS47L92 and CS47L15.
- Support Allwinner Sunxi V3S.
- Support Aspeed 2600 BMC.
- Support Qualcomm SC7180.
- Support Marvell MVEBU CS115.
Driver improvements:
- Clean up a few drivers to use the devm_platform_ioremap_resource()
helper.
- Pass the irqchip when registering the gpio_chip in some pin
controllers that are also GPIO controllers.
- Support suspend/resume in the Tegra driver.
- Support pull-up on the Broadcom BCM2711.
- The Intel driver can now request locked pads.
- Fix the UFS reset pin in the Qualcomm SDM845 driver.
-----BEGIN PGP SIGNATURE-----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=2nNz
-----END PGP SIGNATURE-----
Merge tag 'pinctrl-v5.4-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control updates from Linus Walleij:
"This is the bulk of pin control changes for the v5.4 kernel cycle:
Core changes:
- Fix errors in example code in the documentation.
New drivers:
- Add support for JZ4760, JZ4760B, X1000, X1000E and X1500 to the
Ingenic driver.
- Support Cirrus Logic Madera CS47L92 and CS47L15.
- Support Allwinner Sunxi V3S.
- Support Aspeed 2600 BMC.
- Support Qualcomm SC7180.
- Support Marvell MVEBU CS115.
Driver improvements:
- Clean up a few drivers to use the devm_platform_ioremap_resource()
helper.
- Pass the irqchip when registering the gpio_chip in some pin
controllers that are also GPIO controllers.
- Support suspend/resume in the Tegra driver.
- Support pull-up on the Broadcom BCM2711.
- The Intel driver can now request locked pads.
- Fix the UFS reset pin in the Qualcomm SDM845 driver"
* tag 'pinctrl-v5.4-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (112 commits)
pinctrl: meson-gxbb: Fix wrong pinning definition for uart_c
pinctrl: sh-pfc: Unlock on error in sh_pfc_func_set_mux()
pinctrl: bcm: remove redundant assignment to pointer log
pinctrl: iproc: Add 'get_direction' support
pinctrl: iproc-gpio: Handle interrupts for multiple instances
pinctrl: iproc-gpio: Fix incorrect pinconf configurations
pinctrl: intel: mark intel_pin_to_gpio __maybe_unused
pinctrl: qcom: sdm845: Fix UFS_RESET pin
pinctrl: mvebu: add additional variant for standalone CP115
pinctrl: mvebu: Add CP110 missing pin functionality
dt-bindings: cp110: document the new CP115 pinctrl compatible
pinctrl: bcm2835: Pass irqchip when adding gpiochip
pinctrl: meson: meson: Add of_node_put() before return
pinctrl/gpio: Take MUX usage into account
dt-bindings: pinctrl: qcom-pmic-gpio: Add pm8150l support
dt-bindings: pinctrl: qcom-pmic-gpio: Add pm8150b support
dt-bindings: pinctrl: qcom-pmic-gpio: Add pm8150 support
pinctrl: amd: disable spurious-firing GPIO IRQs
pinctrl: rza2: Include the appropriate headers
pinctrl: rza2: Drop driver use of consumer flags
...
After changing the valid_mask for the struct gpio_chip
to detect the need and presence of a valid mask with the
presence of a .init_valid_mask() callback to fill it in,
we augment the gpio_irq_chip to use the same logic.
Switch all driver using the gpio_irq_chio valid_mask
over to this new method.
This makes sure the valid_mask for the gpio_irq_chip gets
filled in when we add the gpio_chip, which makes it a
little easier to switch over drivers using the old
way of setting up gpio_irq_chip over to the new method
of passing the gpio_irq_chip along with the gpio_chip.
(See drivers/gpio/TODO for details.)
Cc: Joel Stanley <joel@jms.id.au>
Cc: Thierry Reding <treding@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Link: https://lore.kernel.org/r/20190904140104.32426-1-linus.walleij@linaro.org
The intel_pin_to_gpio() function is only called by the
PM support functions and causes a warning when those are disabled:
drivers/pinctrl/intel/pinctrl-intel.c:841:12: error: unused function 'intel_pin_to_gpio' [-Werror,-Wunused-function]
Mark it __maybe_unused to suppress the warning.
Suggested-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Chris Chiu <chiu@endlessm.com>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
On Asus X571GT, GPIO 297 is configured as an interrupt and serves
for the touchpad. The touchpad will report input events much less
than expected after S3 suspend/resume, which results in extremely
slow cursor movement. However, the number of interrupts observed
from /proc/interrupts increases much more than expected even no
touching touchpad.
This is due to the value of PADCFG0 of PIN 225 for the interrupt
has been changed from 0x80800102 to 0x80100102. The GPIROUTIOXAPIC
is toggled on which results in the spurious interrupts. The PADCFG0
of PIN 225 is expected to be saved during suspend, but the 297 is
saved instead because the gpiochip_line_is_irq() expect the GPIO
offset but what's really passed to it is PIN number. In this case,
the /sys/kernel/debug/pinctrl/INT3450:00/gpio-ranges shows
288: INT3450:00 GPIOS [436 - 459] PINS [216 - 239]
So gpiochip_line_is_irq() returns true for GPIO offset 297, the
suspend routine spuriously saves the content for PIN 297 which
we expect to save for PIN 225.
This commit maps the PIN number to GPIO offset first in the
intel_pinctrl_should_save() to make sure the values for the
specific PINs can be correctly saved and then restored.
Fixes: c538b94367 ("pinctrl: intel: Only restore pins that are used by the driver")
Signed-off-by: Chris Chiu <chiu@endlessm.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Some firmwares would like to protect pads from being modified by OS
and at the same time provide them to OS as a resource. So, the driver
in such circumstances may request pad and may not change its state.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Version 1.08 of pin list has some changes in pin names for Intel Denverton.
Update the driver accordingly.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
We don't need dev_err() messages when platform_get_irq() fails now that
platform_get_irq() prints an error message itself when something goes
wrong. Let's remove these prints with a simple semantic patch.
// <smpl>
@@
expression ret;
struct platform_device *E;
@@
ret =
(
platform_get_irq(E, ...)
|
platform_get_irq_byname(E, ...)
);
if ( \( ret < 0 \| ret <= 0 \) )
{
(
-if (ret != -EPROBE_DEFER)
-{ ...
-dev_err(...);
-... }
|
...
-dev_err(...);
)
...
}
// </smpl>
While we're here, remove braces on if statements that only have one
statement (manually).
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: linux-gpio@vger.kernel.org
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Mika Westerberg <mika.westerberg@linux.intel.com>
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
We don't need dev_err() messages when platform_get_irq() fails now that
platform_get_irq() prints an error message itself when something goes
wrong. Let's remove these prints with a simple semantic patch.
// <smpl>
@@
expression ret;
struct platform_device *E;
@@
ret =
(
platform_get_irq(E, ...)
|
platform_get_irq_byname(E, ...)
);
if ( \( ret < 0 \| ret <= 0 \) )
{
(
-if (ret != -EPROBE_DEFER)
-{ ...
-dev_err(...);
-... }
|
...
-dev_err(...);
)
...
}
// </smpl>
While we're here, remove braces on if statements that only have one
statement (manually).
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: linux-gpio@vger.kernel.org
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Mika Westerberg <mika.westerberg@linux.intel.com>
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Replace hard coded constants with self-explanatory names, i.e.
use NSEC_PER_USEC for debounce calculus.
While here, add a unit suffix to debounce period constant.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
We have some data structures duplicated across the drivers.
Let's deduplicate them by using ones that being provided by
pinctrl-intel.h.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Since some of the GPIO controllers use different Interrupt Status offset,
it make sense to provide it explicitly in the drivers.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Since some of the GPIO controllers use different Interrupt Status offset,
it make sense to provide it explicitly in the driver.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Since some of the GPIO controllers use different Interrupt Status offset,
it make sense to provide it explicitly in the driver.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Since some of the GPIO controllers use different Interrupt Status offset,
it make sense to provide it explicitly in the driver.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Since some of the GPIO controllers use different Interrupt Status offset,
it make sense to provide it explicitly in the driver.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Since some of the GPIO controllers use different Interrupt Status offset,
it make sense to provide it explicitly in the driver.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Since some of the GPIO controllers use different Interrupt Status offset,
it make sense to provide it explicitly in the driver.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Since some of the GPIO controllers use different Interrupt Status offset,
it make sense to provide it explicitly in the driver.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
There is more generic and simpler validation just against the nregs.
Using it allows to drop customization from the intel_get_padcfg().
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
There is no need to duplicate the check which is done in the common
intel_pinctrl_probe().
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Use the new helper that wraps the calls to platform_get_resource()
and devm_ioremap_resource() together.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Use the new helper that wraps the calls to platform_get_resource()
and devm_ioremap_resource() together.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Use the new helper that wraps the calls to platform_get_resource()
and devm_ioremap_resource() together.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Use the new helper that wraps the calls to platform_get_resource()
and devm_ioremap_resource() together.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
cycle:
Core changes:
- Device links can optionally be added between a pin control
producer and its consumers. This will affect how the system
power management is handled: a pin controller will not suspend
before all of its consumers have been suspended. This was
necessary for the ST Microelectronics STMFX expander and
need to be tested on other systems as well: it makes sense
to make this default in the long run. Right now it is
opt-in per driver.
- Drive strength can be specified in microamps. With decreases
in silicon technology, milliamps isn't granular enough, let's
make it possible to select drive strengths in microamps. Right
now the Meson (AMlogic) driver needs this.
New drivers:
- New subdriver for the Tegra 194 SoC.
- New subdriver for the Qualcomm SDM845.
- New subdriver for the Qualcomm SM8150.
- New subdriver for the Freescale i.MX8MN (Freescale is now a
product line of NXP).
- New subdriver for Marvell MV98DX1135.
Driver improvements:
- The Bitmain BM1880 driver now supports pin config in
addition to muxing.
- The Qualcomm drivers can now reserve some GPIOs as taken
aside and not usable for users. This is used in ACPI systems
to take out some GPIO lines used by the BIOS so that
noone else (neither kernel nor userspace) will play with them
by mistake and crash the machine.
- A slew of refurbishing around the Aspeed drivers (board
management controllers for servers) in preparation for the
new Aspeed AST2600 SoC.
- A slew of improvements over the SH PFC drivers as usual.
- Misc cleanups and fixes.
-----BEGIN PGP SIGNATURE-----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=Wdw1
-----END PGP SIGNATURE-----
Merge tag 'pinctrl-v5.3-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control updates from Linus Walleij:
"This is the bulk of pin control changes for the v5.3 kernel cycle:
Core changes:
- Device links can optionally be added between a pin control producer
and its consumers. This will affect how the system power management
is handled: a pin controller will not suspend before all of its
consumers have been suspended.
This was necessary for the ST Microelectronics STMFX expander and
need to be tested on other systems as well: it makes sense to make
this default in the long run.
Right now it is opt-in per driver.
- Drive strength can be specified in microamps. With decreases in
silicon technology, milliamps isn't granular enough, let's make it
possible to select drive strengths in microamps.
Right now the Meson (AMlogic) driver needs this.
New drivers:
- New subdriver for the Tegra 194 SoC.
- New subdriver for the Qualcomm SDM845.
- New subdriver for the Qualcomm SM8150.
- New subdriver for the Freescale i.MX8MN (Freescale is now a product
line of NXP).
- New subdriver for Marvell MV98DX1135.
Driver improvements:
- The Bitmain BM1880 driver now supports pin config in addition to
muxing.
- The Qualcomm drivers can now reserve some GPIOs as taken aside and
not usable for users. This is used in ACPI systems to take out some
GPIO lines used by the BIOS so that noone else (neither kernel nor
userspace) will play with them by mistake and crash the machine.
- A slew of refurbishing around the Aspeed drivers (board management
controllers for servers) in preparation for the new Aspeed AST2600
SoC.
- A slew of improvements over the SH PFC drivers as usual.
- Misc cleanups and fixes"
* tag 'pinctrl-v5.3-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (106 commits)
pinctrl: aspeed: Strip moved macros and structs from private header
pinctrl: aspeed: Fix missed include
pinctrl: baytrail: Use GENMASK() consistently
pinctrl: baytrail: Re-use data structures from pinctrl-intel.h
pinctrl: baytrail: Use defined macro instead of magic in byt_get_gpio_mux()
pinctrl: qcom: Add SM8150 pinctrl driver
dt-bindings: pinctrl: qcom: Add SM8150 pinctrl binding
dt-bindings: pinctrl: qcom: Document missing gpio nodes
pinctrl: aspeed: Add implementation-related documentation
pinctrl: aspeed: Split out pinmux from general pinctrl
pinctrl: aspeed: Clarify comment about strapping W1C
pinctrl: aspeed: Correct comment that is no longer true
MAINTAINERS: Add entry for ASPEED pinctrl drivers
dt-bindings: pinctrl: aspeed: Convert AST2500 bindings to json-schema
dt-bindings: pinctrl: aspeed: Convert AST2400 bindings to json-schema
dt-bindings: pinctrl: aspeed: Split bindings document in two
pinctrl: qcom: Add irq_enable callback for msm gpio
pinctrl: madera: Fixup SPDX headers
pinctrl: qcom: sdm845: Fix CONFIG preprocessor guard
pinctrl: tegra: Add bitmask support for parked bits
...
Use GENMASK() macro for all definitions where it's appropriate.
No functional change intended.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20190703151554.30454-1-andriy.shevchenko@linux.intel.com
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
We have some data structures duplicated across the drivers.
Let's deduplicate them by using ones that being provided by
pinctrl-intel.h.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20190703003018.75186-2-andriy.shevchenko@linux.intel.com
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
By the fact byt_get_gpio_mux() returns a value of mux settings as
it is represented in hardware. Use defined macro instead of magic numbers
to clarify this.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20190703003018.75186-1-andriy.shevchenko@linux.intel.com
Reviewed-By: Enrico Weigelt <info@metux.net>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Commit a939bb57cd ("pinctrl: intel: implement gpio_irq_enable") was
added because clearing interrupt status bit is required to avoid
unexpected behavior.
Turns out the unmask callback also needs the fix, which can solve weird
IRQ triggering issues on I2C touchpad ELAN1200.
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
We better to use usual pattern for read-modify-update,
than doing some operations in definition block.
No functional change.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
The touchpad of the ASUS laptops E403NA, X540NA, X541NA are not
responsive after suspend/resume. The following error message
shows after resume.
i2c_hid i2c-ELAN1200:00: failed to reset device.
On these laptops, the touchpad interrupt is connected via a GPIO
pin which is controlled by Intel pinctrl. After system resumes,
the GPIO is in ACPI mode and no longer works as an IRQ.
This commit saves the HOSTSW_OWN value during suspend, make sure
the HOSTSW_OWN mode remains the same after resume.
Signed-off-by: Chris Chiu <chiu@endlessm.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
In current driver, SET_LATE_SYSTEM_SLEEP_PM_OPS is used to install the
callbacks for suspend/resume.
GPIO pin may be used as the interrupt pin by some device. However, using
SET_LATE_SYSTEM_SLEEP_PM_OPS() to install the callbacks, the resume
callback is called after resume_device_irqs(). Unintended interrupts may
arrive due to resuming device irqs first, but the GPIO controller is not
properly restored.
Normally, for a SMP system, there are multiple cores, so even when there are
unintended interrupts, BSP gets the chance to initialize the GPIO chip soon.
But when there is only 1 core is active (other cores are offlined or
single core) during resume, it is more easily to observe the unintended
interrupts.
This patch renames the suspend/resume function by adding suffix "_noirq",
and installs the callbacks using SET_NOIRQ_SYSTEM_SLEEP_PM_OPS().
Signed-off-by: Binbin Wu <binbin.wu@intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Version 1.13c of pin list has some changes in pin names for
Intel Cedarfork.
Update the driver accordingly.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Linus Walleij <linus.walleij@linar.org>
saved-context in byt_gpio_probe is allocated via devm_kcalloc and is
used without checking for NULL in later functions. This patch avoids
such a scenario.
Signed-off-by: Aditya Pakki <pakki001@umn.edu>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Well, hopefully 3rd time is a charm. We tried making that check
DMI_BIOS_VERSION and DMI_BOARD_VERSION, but the real one is
DMI_PRODUCT_VERSION.
Fixes: 86c5dd6860 ("pinctrl: cherryview: limit Strago DMI workarounds to version 1.0")
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=197953
Bugzilla: https://bugzilla.redhat.com/show_bug.cgi?id=1631930
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Clearing the GPIO_EN bit from chv_gpio_disable_free is a bad idea and
pinctrl-cherryview.c is the only Intel pinctrl driver doing something
like this.
Clearing the GPIO_EN bit means that if the pin was an output it is now
effectively floating. The datasheet is not clear what happens to pull ups /
downs in this case, but from testing it looks like these are disabled too,
also floating input pins.
One example where this is causing issues is the soc_button_array input
driver, this parses ACPI tables to create 2 platform devices for the
gpio_keys input driver. The list of GPIOs is passed through struct
gpio_keys_platform_data which uses gpio numbers rather then gpio_desc
pointers.
The buttons handled by this drivers short the pin to ground when pressed
and the volume buttons rely on the SoC's internal pull-up to pull the
pin high when the button is not pressed.
To get the gpio number, the soc_button_array code calls gpiod_get_index
followed by a desc_to_gpio call and then gpiod_put on the gpio_desc.
This last call causes chv_gpio_disable_free to clear the GPIO_EN bit.
When the gpio_keys driver then loads next it gets the gpio_desc again
causing the GPIO_EN bit to be set again and immediately reads the GPIO
value which for the volume buttons reads 0 at this time, causing a spurious
press of the volume buttons to get reported.
Putting a small delay between the gpio_desc request and the read fixes
this, I assume that this is caused by the pull-up being temporarily
disabled while the GPIO_EN bit is cleared as the powerbutton which also
has its GPIO_EN bit cleared does not have this problem.
The soc_button_array code is not the only code temporarily requesting GPIOs
the DWC3 PCI code also does this, to set the enable and reset GPIOs for the
external phy, so that the code instantiating the ULPI phy can read the
vendor and product ID registers from the phy. These GPIOs are released
after this so that the PHY driver can claim and use them when it loads.
Another example of temporary GPIO usage would be a user-space set_gpio
utility using the userspace ioctls to set a GPIO as output value 0 or 1,
having the GPIO revert to floating as soon as this utility exits would
certainly be unexpected behavior.
One argument in favor of clearing the GPIO_EN bit is if the GPIO is going
to be muxed to another function after being released, but in that case
chv_pinmux_set_mux() already clears it.
TL;DR: Clearing the GPIO_EN bit from is a bad idea, this commit therefor
removes the clearing from chv_gpio_disable_free(), replacing it with code
to clear the interrupt-trigger condition so that the GPIO stops generating
interrupts when released, as pinctrl-baytrail.c does.
Note this commit adds a !chv_pad_locked() condition to the trigger clearing
call, which the original GPIO_EN clearing code was missing.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
This is a preparation patch for clearing the interrupt trigger from
chv_gpio_disable_free().
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Remove comma from terminator line to allow compiler fail
in case an entry has been put in a wrong place by any weird reason.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Remove comma from terminator line to allow compiler fail
in case an entry has been put in a wrong place by any weird reason.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Remove comma from terminator line to allow compiler fail
in case an entry has been put in a wrong place by any weird reason.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Remove comma from terminator line to allow compiler fail
in case an entry has been put in a wrong place by any weird reason.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Remove comma from terminator line to allow compiler fail
in case an entry has been put in a wrong place by any weird reason.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
There is no need to include acpi.h since driver doesn't use anything from it
except the propagation of mod_devicetable.h.
Include latter directly instead.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
There is no need to include acpi.h since driver doesn't use anything from it
except the propagation of mod_devicetable.h.
Include latter directly instead.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
There is no need to include acpi.h since driver doesn't use anything from it
except the propagation of mod_devicetable.h.
Include latter directly instead.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
The reason of including <linux/bitops.h> here is just for BIT() and Co macros.
Since commit 8bd9cb51da
("... Move some macros from <linux/bitops.h> to a new <linux/bits.h> file"),
<linux/bits.h> is enough for such compile-time macros.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Since there are no more users, unexport it and make static.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
The local ->probe() stub does nothing except calling
a generic Intel pin control probe function. Thus,
it's not needed and generic function may be called directly.
Convert the driver accordingly.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
The local ->probe() stub does nothing except calling
a generic Intel pin control probe function. Thus,
it's not needed and generic function may be called directly.
Convert the driver accordingly.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
The local ->probe() stub does nothing except calling
a generic Intel pin control probe function. Thus,
it's not needed and generic function may be called directly.
Convert the driver accordingly.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
The local ->probe() stub does nothing except calling
a generic Intel pin control probe function. Thus,
it's not needed and generic function may be called directly.
Convert the driver accordingly.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
The local ->probe() stub does nothing except calling
a generic Intel pin control probe function. Thus,
it's not needed and generic function may be called directly.
Convert the driver accordingly.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
The local ->probe() stub does nothing except calling
a generic Intel pin control probe function. Thus,
it's not needed and generic function may be called directly.
Convert the driver accordingly.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
The local ->probe() stub does nothing except calling
a generic Intel pin control probe function. Thus,
it's not needed and generic function may be called directly.
Convert the driver accordingly.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
We should get 'driver_data' from 'struct device' directly. Going via
platform_device is an unneeded step back and forth.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
We should get 'driver_data' from 'struct device' directly. Going via
platform_device is an unneeded step back and forth.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
We should get 'driver_data' from 'struct device' directly. Going via
platform_device is an unneeded step back and forth.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
No functional change.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The local ->probe() stub does nothing except calling
a generic Intel pin control probe function. Thus,
it's not needed and generic function may be called directly.
This patch converts the driver accordingly.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
According to an updated pin list few names of the pins can be spelled better,
taking into account their primary functions.
Thus, update a pin list to cover B0 stepping.
Note, SPI numbering had been fixed even in A0 public documentation.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The parameter 'community' had been spelled incorrectly.
Fix it here.
As a side effect it satisfies static checkers that issue
the following warnings:
drivers/pinctrl/intel/pinctrl-intel.c:845: warning: Function parameter or member 'community' not described in 'intel_gpio_to_pin'
drivers/pinctrl/intel/pinctrl-intel.c:845: warning: Excess function parameter 'commmunity' description in 'intel_gpio_to_pin'
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Simple type conversion with no functional change implied.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Simple type conversion with no functional change implied.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Simple type conversion with no functional change implied.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Simple type conversion with no functional change implied.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
-----BEGIN PGP SIGNATURE-----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=dMl4
-----END PGP SIGNATURE-----
Merge tag 'v4.19-rc6' into devel
This is the 4.19-rc6 release
I needed to merge this in because of extensive conflicts in
the MSM and Intel pin control drivers. I know how to resolve
them, so let's do it like this.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This reverts commit 55aedef50d.
Commit 55aedef50d ("pinctrl: intel: Do pin translation when lock IRQ")
added special translation from GPIO number to hardware pin number to
irq_reqres/relres hooks to avoid failure when IRQs are requested. The
actual failure happened inside gpiochip_lock_as_irq() because it calls
gpiod_get_direction() and pinctrl-intel.c::intel_gpio_get_direction()
implementation originally missed the translation so the two hooks made
it work by skipping the ->get_direction() call entirely (it overwrote
the default GPIOLIB provided functions).
The proper fix that adds translation to GPIO callbacks was merged with
commit 96147db1e1 ("pinctrl: intel: Do pin translation in other GPIO
operations as well"). This allows us to use the default GPIOLIB provided
functions again.
In addition as find out by Benjamin Tissoires the two functions
(intel_gpio_irq_reqres()/intel_gpio_irq_relres()) now cause problems of
their own because they operate on pin numbers and pass that pin number
to gpiochip_lock_as_irq() which actually expects a GPIO number.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=199911
Fixes: 55aedef50d ("pinctrl: intel: Do pin translation when lock IRQ")
Reported-and-tested-by: Benjamin Tissoires <benjamin.tissoires@gmail.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
It turns out the HOSTSW_OWN register offset is different between LP and
H variants. The latter should use 0xc0 instead so fix that.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=199911
Fixes: a663ccf0fe ("pinctrl: intel: Add Intel Cannon Lake PCH-H pin controller support")
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Consolidate IO accessors in the code to make maintenance a little bit easier
in the future.
No functional change intended.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
mrfld_read_bufcfg() helper checks if pin is correct and reads back
the current value of corresponding BUFCFG register.
While it adds lines of code it will be easier to maintain in the future.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
For some reason I thought GPIOLIB handles translation from GPIO ranges
to pinctrl pins but it turns out not to be the case. This means that
when GPIOs operations are performed for a pin controller having a custom
GPIO base such as Cannon Lake and Ice Lake incorrect pin number gets
used internally.
Fix this in the same way we did for lock/unlock IRQ operations and
translate the GPIO number to pin before using it.
Fixes: a60eac3239 ("pinctrl: intel: Allow custom GPIO base for pad groups")
Reported-by: Rajat Jain <rajatja@google.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Tested-by: Rajat Jain <rajatja@google.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
There is no need to include linux/init.h when at the same time
we include linux/module.h.
Remove redundant inclusion.
While here, sort header block alphabetically for easy maintenance.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Compiler unsatisfied to see half described data structures
and issues warnings:
drivers/pinctrl/intel/pinctrl-cherryview.c:136: warning: Function parameter or member 'acpi_space_id' not described in 'chv_community'
drivers/pinctrl/intel/pinctrl-cherryview.c:169: warning: Function parameter or member 'saved_intmask' not described in 'chv_pinctrl'
drivers/pinctrl/intel/pinctrl-cherryview.c:169: warning: Function parameter or member 'saved_pin_context' not described in 'chv_pinctrl'
To satisfy it, describe mentioned members.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
For the long time no one complained about unused groups of pins
for fSPI and SMBUS.
Remove them for good and at the same time satisfy compiler,
otherwise get warning:
CC drivers/pinctrl/intel/pinctrl-cherryview.o
drivers/pinctrl/intel/pinctrl-cherryview.c:285:23: warning: ‘southwest_smbus_pins’ defined but not used [-Wunused-const-variable=]
static const unsigned southwest_smbus_pins[] = { 79, 81, 82 };
^~~~~~~~~~~~~~~~~~~~
drivers/pinctrl/intel/pinctrl-cherryview.c:269:23: warning: ‘southwest_fspi_pins’ defined but not used [-Wunused-const-variable=]
static const unsigned southwest_fspi_pins[] = { 0, 1, 2, 3, 4, 5, 6, 7 };
^~~~~~~~~~~~~~~~~~~
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
We have some data structures duplicated across the drivers.
Let's deduplicate them by using ones that being provided by
pinctrl-intel.h.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Since the driver can't be compiled as a module, there is no need
to use no-op macros in the code.
Thus, remove unneeded MODULE_DEVICE_TABLE() macro from the driver.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
We now using a common macro for PM operations in pin control drivers for Intel
SoCs, and since that macro relies on the definition and macro from linux/pm.h
header file, it's logical to include it directly in pinctrl-intel.h. Otherwise
it's a bit fragile and requires a proper ordering of header inclusion in C
files.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The gpio base for GPP-E was set incorrectly to 258 instead of 256,
preventing the touchpad working on my Tong Fang GK5CN5Z laptop.
Buglink: https://bugzilla.kernel.org/show_bug.cgi?id=200787
Signed-off-by: Simon Detheridge <s@sd.ai>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
These drivers are GPIO drivers, and the do not need to use the
legacy header in <linux/gpio.h>, go directly for
<linux/gpio/driver.h> instead.
Replace any use of GPIOF_* with 0/1, these flags are for
consumers, not drivers.
Get rid of a few gpio_to_irq() users that was littering
around the place, use local callbacks or avoid using it at
all.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Instead of open coding same structure definition for PM operations,
replace it with a common macro.
No functional change intended.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Instead of open coding same structure definition for PM operations,
replace it with a common macro.
No functional change intended.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Instead of open coding same structure definition for PM operations,
replace it with a common macro.
No functional change intended.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Instead of open coding same structure definition for PM operations,
replace it with a common macro.
No functional change intended.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Instead of open coding same structure definition for PM operations,
replace it with a common macro.
No functional change intended.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Instead of open coding same structure definition for PM operations,
replace it with a common macro.
No functional change intended.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Instead of open coding same structure definition for PM operations,
replace it with a common macro.
No functional change intended.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Instead of open coding same structure definition for PM operations,
replace it with a common macro.
No functional change intended.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This common macro will simplify the code of pin control drivers
for Intel SoCs.
Suggested-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Get rid of code duplication by converting to use intel_pinctrl_probe_by_hid().
No functional change intended.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Get rid of code duplication by converting to use intel_pinctrl_probe_by_hid().
No functional change intended.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Introduce intel_pinctrl_probe_by_hid() internal API to simplify drivers,
which are using ACPI _HID to distinguish which SoC data needs to be used
when being probed.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Get rid of code duplication by converting to use device_get_match_data().
No functional change intended.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Get rid of code duplication by converting to use intel_pinctrl_probe_by_uid().
No functional change intended.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Get rid of code duplication by converting to use intel_pinctrl_probe_by_uid().
No functional change intended.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Introduce intel_pinctrl_probe_by_uid() internal API to simplify drivers,
which are using ACPI _UID to distinguish which SoC data needs to be used
when being probed.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The parameter 'community' had been spelled incorrectly.
Fix it here.
As a side effect it satisfies static checkers that issue
the following warnings:
drivers/pinctrl/intel/pinctrl-intel.c:845: warning: Function parameter or member 'community' not described in 'intel_gpio_to_pin'
drivers/pinctrl/intel/pinctrl-intel.c:845: warning: Excess function parameter 'commmunity' description in 'intel_gpio_to_pin'
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Here is the bit set of char/misc drivers for 4.19-rc1
There is a lot here, much more than normal, seems like everyone is
writing new driver subsystems these days... Anyway, major things here
are:
- new FSI driver subsystem, yet-another-powerpc low-level
hardware bus
- gnss, finally an in-kernel GPS subsystem to try to tame all of
the crazy out-of-tree drivers that have been floating around
for years, combined with some really hacky userspace
implementations. This is only for GNSS receivers, but you
have to start somewhere, and this is great to see.
Other than that, there are new slimbus drivers, new coresight drivers,
new fpga drivers, and loads of DT bindings for all of these and existing
drivers.
Full details of everything is in the shortlog.
All of these have been in linux-next for a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCW3g7ew8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ykfBgCeOG0RkSI92XVZe0hs/QYFW9kk8JYAnRBf3Qpm
cvW7a+McOoKz/MGmEKsi
=TNfn
-----END PGP SIGNATURE-----
Merge tag 'char-misc-4.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver updates from Greg KH:
"Here is the bit set of char/misc drivers for 4.19-rc1
There is a lot here, much more than normal, seems like everyone is
writing new driver subsystems these days... Anyway, major things here
are:
- new FSI driver subsystem, yet-another-powerpc low-level hardware
bus
- gnss, finally an in-kernel GPS subsystem to try to tame all of the
crazy out-of-tree drivers that have been floating around for years,
combined with some really hacky userspace implementations. This is
only for GNSS receivers, but you have to start somewhere, and this
is great to see.
Other than that, there are new slimbus drivers, new coresight drivers,
new fpga drivers, and loads of DT bindings for all of these and
existing drivers.
All of these have been in linux-next for a while with no reported
issues"
* tag 'char-misc-4.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (255 commits)
android: binder: Rate-limit debug and userspace triggered err msgs
fsi: sbefifo: Bump max command length
fsi: scom: Fix NULL dereference
misc: mic: SCIF Fix scif_get_new_port() error handling
misc: cxl: changed asterisk position
genwqe: card_base: Use true and false for boolean values
misc: eeprom: assignment outside the if statement
uio: potential double frees if __uio_register_device() fails
eeprom: idt_89hpesx: clean up an error pointer vs NULL inconsistency
misc: ti-st: Fix memory leak in the error path of probe()
android: binder: Show extra_buffers_size in trace
firmware: vpd: Fix section enabled flag on vpd_section_destroy
platform: goldfish: Retire pdev_bus
goldfish: Use dedicated macros instead of manual bit shifting
goldfish: Add missing includes to goldfish.h
mux: adgs1408: new driver for Analog Devices ADGS1408/1409 mux
dt-bindings: mux: add adi,adgs1408
Drivers: hv: vmbus: Cleanup synic memory free path
Drivers: hv: vmbus: Remove use of slow_virt_to_phys()
Drivers: hv: vmbus: Reset the channel callback in vmbus_onoffer_rescind()
...
gpiochip_lock_as_irq() may return a few error codes,
do not shadow them by -EINVAL and let caller to decide.
No functional change intended.
Cc: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
For further investigation the actual result in interrupt status register
is needed.
Signed-off-by: Alexander Stein <alexander.stein@systec-electronic.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The driver was written based on an assumption that BIOS provides
unordered communities in ACPI DSDT. Nevertheless, it seems that
BIOS getting fixed before being provisioned to OxM:s.
So does driver.
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=199911
Reported-by: Marc Landolt <2009@marclandolt.ch>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Fixes: a663ccf0fe ("pinctrl: intel: Add Intel Cannon Lake PCH-H pin controller support")
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Default GPIOLIB callbacks for request and release IRQ do not do a GPIO
to pin translation which is necessary for Intel hardware, such as Intel
Cannonlake. Absence of the translation prevents some pins to be locked
as IRQ due to direction check. Introduce own callbacks to make
translation possible to avoid above issue.
Fixes: a60eac3239 ("pinctrl: intel: Allow custom GPIO base for pad groups")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Addresses-Coverity-ID: 1292308 ("Missing break in switch")
Addresses-Coverity-ID: 1292309 ("Missing break in switch")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
At over 4000 #includes, <linux/platform_device.h> is the 9th most
#included header file in the Linux kernel. It does not need
<linux/mod_devicetable.h>, so drop that header and explicitly add
<linux/mod_devicetable.h> to source files that need it.
4146 #include <linux/platform_device.h>
After this patch, there are 225 files that use <linux/mod_devicetable.h>,
for a reduction of around 3900 times that <linux/mod_devicetable.h>
does not have to be read & parsed.
225 #include <linux/mod_devicetable.h>
This patch was build-tested on 20 different arch-es.
It also makes these drivers SubmitChecklist#1 compliant.
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Reported-by: kbuild test robot <lkp@intel.com> # drivers/media/platform/vimc/
Reported-by: kbuild test robot <lkp@intel.com> # drivers/pinctrl/pinctrl-u300.c
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reduce size of duplicated comments by switching to use SPDX identifier.
No functional change.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This adds pinctrl/GPIO support for Intel Ice Lake PCH. The Ice Lake PCH
GPIO is based on the same version of the Intel GPIO hardware than Intel
Cannon Lake with different set of pins and ACPI ID.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The driver missed the fact that PECI_SMB_DATA has moved from EAST
community 224 to 182 instead. Correct the pin ordering accordingly.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
No core changes this time! Just a calm all-over-the-place
drivers, updates and fixes cycle as it seems.
New drivers/subdrivers:
- Actions Semiconductor S900 driver with more Actions
variants for S700, S500 in the pipe. Also generic GPIO
support on top of the same driver and IRQ support is in
the pipe.
- Renesas r8a77470 PFC support.
- Renesas r8a77990 PFC support.
- Allwinner Sunxi H6 R_PIO support.
- Rockchip PX30 support.
- Meson Meson8m2 support.
- Remove support for the ill-fated Samsung Exynos 5440 SoC.
Improvements:
- Context save/restore support in pinctrl-single.
- External interrupt support for the Mediatek MT7622.
- Qualcomm ACPI HID QCOM8002 supported.
Fixes:
- Fix up suspend/resume support for Exynos 5433.
- Fix Strago DMI fixes on the Intel Cherryview.
-----BEGIN PGP SIGNATURE-----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=6On2
-----END PGP SIGNATURE-----
Merge tag 'pinctrl-v4.18-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control updates from Linus Walleij:
"This is the bulk of pin control changes for v4.18.
No core changes this time! Just a calm all-over-the-place drivers,
updates and fixes cycle as it seems.
New drivers/subdrivers:
- Actions Semiconductor S900 driver with more Actions variants for
S700, S500 in the pipe. Also generic GPIO support on top of the
same driver and IRQ support is in the pipe.
- Renesas r8a77470 PFC support.
- Renesas r8a77990 PFC support.
- Allwinner Sunxi H6 R_PIO support.
- Rockchip PX30 support.
- Meson Meson8m2 support.
- Remove support for the ill-fated Samsung Exynos 5440 SoC.
Improvements:
- Context save/restore support in pinctrl-single.
- External interrupt support for the Mediatek MT7622.
- Qualcomm ACPI HID QCOM8002 supported.
Fixes:
- Fix up suspend/resume support for Exynos 5433.
- Fix Strago DMI fixes on the Intel Cherryview"
* tag 'pinctrl-v4.18-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (72 commits)
pinctrl: cherryview: limit Strago DMI workarounds to version 1.0
pinctrl: at91-pio4: add missing of_node_put
pinctrl: armada-37xx: Fix spurious irq management
gpiolib: discourage gpiochip_add_pin[group]_range for DT pinctrls
pinctrl: msm: fix gpio-hog related boot issues
MAINTAINERS: update entry for Mediatek pin controller
pinctrl: mediatek: remove unused fields in struct mtk_eint_hw
pinctrl: mediatek: use generic EINT register maps for each SoC
pinctrl: mediatek: add EINT support to MT7622 SoC
pinctrl: mediatek: refactor EINT related code for all MediaTek pinctrl can fit
dt-bindings: pinctrl: add external interrupt support to MT7622 pinctrl
pinctrl: freescale: Switch to SPDX identifier
pinctrl: samsung: Fix suspend/resume for Exynos5433 GPF1..5 banks
pinctrl: sh-pfc: rcar-gen3: Fix grammar in static pin comments
pinctrl: sh-pfc: r8a77965: Add I2C pin support
pinctrl: sh-pfc: r8a77990: Add EthernetAVB pins, groups and functions
pinctrl: sh-pfc: r8a77990: Add I2C{1,2,4,5,6,7} pins, groups and functions
pinctrl: sh-pfc: r8a77990: Add SCIF pins, groups and functions
pinctrl: sh-pfc: r8a77990: Add bias pinconf support
pinctrl: sh-pfc: Initial R8A77990 PFC support
...
As Google/Intel will fix the BIOS/Coreboot issues with hardcoding
virtual interrupt numbers for keyboard/touchpad/touchscreen controllers
in ACPI tables, they will also update BOARD version number from 1.0
to 1.1. Let's limit the DMI quirks that try to preserve virtual IRQ
numbers on Strago boards to those that still carry older BIOSes.
Note that ideally not BOARD but BIOS version should have been updated.
However the BIOS version used by Chrome devices has format of
Google_BUILD.BRANCH.PATCH which is not well suited for DMI matching as
we do not have "less than" match mode for DMI data.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=197953
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
It turns out that the Windows GPIO driver for Sunrisepoint PCH-H uses
similar bank structure than it does for Cannon Lake with the exception
that here the bank size is always 24 pins. Starting from pad group E the
BIOS/Windows GPIO numbering does not match the hardware anymore but
instead there are gaps to make each pad group ("bank") consume exactly
24 pins. Because of this Linux does not use correct pins for
GpioIo/GpioIo resources exposed by the BIOS.
This patch aligns the GPIO number space with BIOS/Windows to make sure
the same numbering scheme is used in Linux as well following what we did
already for Intel Cannon Lake.
Link: https://bugzilla.redhat.com/show_bug.cgi?id=1543769
Reported-by: Vivien FRASCA <vivien.frasca@gmail.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
When we dropped the custom Linux GPIO translation it resulted that the
IRQ numbers changed slightly as well. Normally this would be fine
because everyone is expected to use controller relative GPIO numbers and
ACPI GpioIo/GpioInt resources. However, there is a certain set of
Intel_Strago based Chromebooks where i8042 keyboard controller IRQ
number is hardcoded be 182 (this is corrected with newer coreboot but
the older ones still have the hardcoded Linux IRQ number). Because of
this hardcoded IRQ number keyboard on those systems accidentally broke
again.
Fix this by iteratively associating IRQ descriptors to the chip irqdomain
so that there are no gaps on those systems. Other systems are not
affected.
Fixes: 03c4749dd6 ("gpio / ACPI: Drop unnecessary ACPI GPIO to Linux GPIO translation")
Link: https://bugzilla.kernel.org/show_bug.cgi?id=199463
Reported-by: Sultan Alsawaf <sultanxda@gmail.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Allows querying GPIO direction from the pad config register.
If the pad is not in GPIO mode, return an error.
Signed-off-by: Javier Arteaga <javier@emutex.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Core changes:
- After lengthy discussions and partly due to my ignorance, we have
merged a patch making pinctrl_force_default() and pinctrl_force_sleep()
reprogram the states into the hardware of any hogged pins, even
if they are already in the desired state. This only apply to hogged
pins since groups of pins owned by drivers need to be managed by
each driver, lest they could not do things like runtime PM and
put pins to sleeping state even if the system as a whole is not
in sleep.
New drivers:
- New driver for the Microsemi Ocelot SoC. This is used in ethernet
switches.
- The X-Powers AXP209 GPIO driver was extended to also deal with pin
control and moved over from the GPIO subsystem. This circuit is
a mixed-mode integrated circuit which is part of AllWinner designs.
- New subdriver for the Qualcomm MSM8998 SoC, core of a high end
mobile devices (phones) chipset.
- New subdriver for the ST Microelectronics STM32MP157 MPU and
STM32F769 MCU from the STM32 family.
- New subdriver for the MediaTek MT7622 SoC. This is used for routers,
repeater, gateways and such network infrastructure.
- New subdriver for the NXP (former Freescale) i.MX 6ULL. This SoC has
multimedia features and target "smart devices", I guess in-car
entertainment, in-flight entertainment, industrial control panels etc.
General improvements:
- Incremental improvements on the SH-PFC subdrivers for things like
the CAN bus.
- Enable the glitch filter on Baytrail GPIOs used for interrupts.
- Proper handling of pins to GPIO ranges on the Semtec SX150X
- An IRQ setup ordering fix on MCP23S08.
- A good set of janitorial coding style fixes.
-----BEGIN PGP SIGNATURE-----
iQIcBAABAgAGBQJadGEKAAoJEEEQszewGV1zA4QQALs8edxhv4qV5vm50mTdrO3n
QtRhJNb53j6MIKtjFnazMvh6MXRIP+08SyX9sDLi5AxINIVuyQh3mrcB6Zc9zN58
+6jFFOIbfm5E8by4n3wnKm3F/WAbNBZph9eT2Rn3cDv9o9hQbyNJ50sQkQMCjd9X
WGR353c3OL4zb3vU8t72G/RPYUY1w1SkG9bGzRuSif8LawDcN6v6MMo2XhZA6RqM
3qYIG29vJ1n0weggUIBeSAJIzk4eMwcoWCbVWxhns5JGxw5VPES1zbSp1D+mbzRC
01i5Pt/gD+cWN/Kk/zKIMo1OqLAl+uLr6hzepj6W+5wu9CcQz/BgvRx7HUqnqgyh
S8cN4AOgWmW+T75pHypd1WVic3q0RCXkFY8jjHpCATDY+Z+js0lZRs3y4DBiJ2ys
DMVBeumDINKqaZ6aLH6lVkm+SxXOUy143arQQIzi0/F7fAp68i+9ofIO8B5smEmd
0S+3sT0sO5QXVgZJ0t0iGUUG5irXi8XtF5qvRmuFZUe0OLGgKX20oCdC0pH0WU4M
OZO1Bvb8vmn1tddogO2WlHeg6amWdwxtDuBsLRO3YILLu3jwPjhNqNmErXzXEmWt
TY9l2M1uQmoJibNpmTjOzSfj4OtUHMwkDrFRJHAcUPcKwdEy4MyzFL16ATnIwgY9
AmyMLNWJd8Wazgc6BK6w
=gLY/
-----END PGP SIGNATURE-----
Merge tag 'pinctrl-v4.16-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control updates from Linus Walleij:
"This is the bulk of pin control changes for the v4.16 kernel cycle.
Like with GPIO it is actually a bit calm this time.
Core changes:
- After lengthy discussions and partly due to my ignorance, we have
merged a patch making pinctrl_force_default() and
pinctrl_force_sleep() reprogram the states into the hardware of any
hogged pins, even if they are already in the desired state.
This only apply to hogged pins since groups of pins owned by
drivers need to be managed by each driver, lest they could not do
things like runtime PM and put pins to sleeping state even if the
system as a whole is not in sleep.
New drivers:
- New driver for the Microsemi Ocelot SoC. This is used in ethernet
switches.
- The X-Powers AXP209 GPIO driver was extended to also deal with pin
control and moved over from the GPIO subsystem. This circuit is a
mixed-mode integrated circuit which is part of AllWinner designs.
- New subdriver for the Qualcomm MSM8998 SoC, core of a high end
mobile devices (phones) chipset.
- New subdriver for the ST Microelectronics STM32MP157 MPU and
STM32F769 MCU from the STM32 family.
- New subdriver for the MediaTek MT7622 SoC. This is used for
routers, repeater, gateways and such network infrastructure.
- New subdriver for the NXP (former Freescale) i.MX 6ULL. This SoC
has multimedia features and target "smart devices", I guess in-car
entertainment, in-flight entertainment, industrial control panels
etc.
General improvements:
- Incremental improvements on the SH-PFC subdrivers for things like
the CAN bus.
- Enable the glitch filter on Baytrail GPIOs used for interrupts.
- Proper handling of pins to GPIO ranges on the Semtec SX150X
- An IRQ setup ordering fix on MCP23S08.
- A good set of janitorial coding style fixes"
* tag 'pinctrl-v4.16-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (102 commits)
pinctrl: mcp23s08: fix irq setup order
pinctrl: Forward declare struct device
pinctrl: sunxi: Use of_clk_get_parent_count() instead of open coding
pinctrl: stm32: add STM32F769 MCU support
pinctrl: sx150x: Add a static gpio/pinctrl pin range mapping
pinctrl: sx150x: Register pinctrl before adding the gpiochip
pinctrl: sx150x: Unregister the pinctrl on release
pinctrl: ingenic: Remove redundant dev_err call in ingenic_pinctrl_probe()
pinctrl: sprd: Use seq_putc() in sprd_pinconf_group_dbg_show()
pinctrl: pinmux: Use seq_putc() in pinmux_pins_show()
pinctrl: abx500: Use seq_putc() in abx500_gpio_dbg_show()
pinctrl: mediatek: mt7622: align error handling of mtk_hw_get_value call
pinctrl: mediatek: mt7622: fix potential uninitialized value being returned
pinctrl: uniphier: refactor drive strength get/set functions
pinctrl: imx7ulp: constify struct imx_cfg_params_decode
pinctrl: imx: constify struct imx_pinctrl_soc_info
pinctrl: imx7d: simplify imx7d_pinctrl_probe
pinctrl: imx: use struct imx_pinctrl_soc_info as a const
pinctrl: sunxi-pinctrl: fix pin funtion can not be match correctly.
pinctrl: qcom: Add msm8998 pinctrl driver
...
On some systems, some PCB traces attached to GpioInts are routed in such
a way that they pick up enough interference to constantly (many times per
second) trigger.
Enabling glitch-filtering fixes this.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Guenter Roeck reported an interrupt storm on a prototype system which is
based on Cyan Chromebook. The root cause turned out to be a incorrectly
configured pin that triggers spurious interrupts. This will be fixed in
coreboot but currently we need to prevent the interrupt storm from
happening by masking all interrupts (but not GPEs) on those systems.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=197953
Fixes: bcb48cca23 ("pinctrl: cherryview: Do not mask all interrupts in probe")
Reported-and-tested-by: Guenter Roeck <linux@roeck-us.net>
Reported-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
In the (unlikely) event that community->ngpps is zero, or if every
gpp->gpio_base is less than zero, then an ininitialized value in
ret is returned by function intel_gpio_add_pin_ranges. Fix this by
ensuring ret is initialized to zero. It's a moot point, but I think
it is worthwhile ensuring this corner case is fixed.
Detected by CoverityScan, CID#1462415 ("Uninitialized scalar variable")
Fixes: a60eac3239 ("pinctrl: intel: Allow custom GPIO base for pad groups")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
When a GPIO is requested using gpiod_get_* APIs the intel pinctrl driver
switches the pin to GPIO mode and makes sure interrupts are routed to
the GPIO hardware instead of IOAPIC. However, if the GPIO is used
directly through irqchip, as is the case with many I2C-HID devices where
I2C core automatically configures interrupt for the device, the pin is
not initialized as GPIO. Instead we rely that the BIOS configures the
pin accordingly which seems not to be the case at least in Asus X540NA
SKU3 with Focaltech touchpad.
When the pin is not properly configured it might result weird behaviour
like interrupts suddenly stop firing completely and the touchpad stops
responding to user input.
Fix this by properly initializing the pin to GPIO mode also when it is
used directly through irqchip.
Fixes: 7981c0015a ("pinctrl: intel: Add Intel Sunrisepoint pin controller and GPIO support")
Reported-by: Daniel Drake <drake@endlessm.com>
Reported-and-tested-by: Chris Chiu <chiu@endlessm.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The Cannon Lake Windows GPIO driver always exposes 32 pins per "bank"
regardless of whether the hardware actually has that many pins in a pad
group. This means that there are gaps in the GPIO number space even if
such gaps do not exist in the real hardware. To make things worse the
BIOS is also using the same scheme, so for example on Cannon Lake-LP
vGPIO 39 (vSD3_CD_B) the ACPI GpioInt resource has number 231 instead of
the expected 180 (which would be the hardware number).
To make SD card detection and other GPIOs working properly in Linux we
align the pinctrl-cannonlake GPIO numbering to follow the Windows GPIO
driver numbering taking advantage of the gpio_base field introduced in
the previous patch.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Currently we always have direct mapping between GPIO numbers and the
hardware pin numbers. However, there are cases where that's not the case
anymore (more about this in the next patch). Instead we need to be able
to specify custom GPIO base for certain pad groups.
To support this, add a new field (gpio_base) to the pad group structure
and update the core Intel pinctrl driver to handle this accordingly.
Passing 0 as gpio_base will use direct mapping so the existing drivers
do not need to be modified. Passing -1 excludes the whole pad group from
having GPIO mapping.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
We added acpi_gpiochip_pin_to_gpio_offset() because there was a need to
translate from ACPI GpioIo/GpioInt number to Linux GPIO number in the
Cherryview pinctrl driver. This translation is necessary because
Cherryview has gaps in the pin list and the driver used continuous GPIO
number space in Linux side as follows:
created GPIO range 0->7 ==> INT33FF:03 PIN 0->7
created GPIO range 8->19 ==> INT33FF:03 PIN 15->26
created GPIO range 20->25 ==> INT33FF:03 PIN 30->35
created GPIO range 26->33 ==> INT33FF:03 PIN 45->52
created GPIO range 34->43 ==> INT33FF:03 PIN 60->69
created GPIO range 44->54 ==> INT33FF:03 PIN 75->85
For example when ACPI GpioInt resource refers to GPIO 81 (SDMMC3_CD_B)
we translate from pin 81 to the corresponding Linux GPIO number, which
is 50. This number is then used when the GPIO is accessed through gpiolib.
It turns out, this is not necessary at all. We can just pass 1:1 mapping
between Linux GPIO numbers and pin numbers (including gaps) and the
pinctrl core handles all the details automatically:
created GPIO range 0->7 ==> INT33FF:03 PIN 0->7
created GPIO range 15->26 ==> INT33FF:03 PIN 15->26
created GPIO range 30->35 ==> INT33FF:03 PIN 30->35
created GPIO range 45->52 ==> INT33FF:03 PIN 45->52
created GPIO range 60->69 ==> INT33FF:03 PIN 60->69
created GPIO range 75->85 ==> INT33FF:03 PIN 75->85
Here GPIO 81 is exactly same than the hardware pin 81 (SDMMC3_CD_B).
As an added bonus this simplifies both the ACPI GPIO core code and the
Cherryview pinctrl driver.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
On Intel Merrifield the pin control device is a separate IP block
without any PCI ID assigned.
Though, recently we got an allocated ACPI ID for it, so, let's use fresh
ID.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
UART2 RTS is mode 2 of the pin.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
kernel cycle:
Core:
- The pin control Kconfig entry PINCTRL is now turned into
a menuconfig option. This obviously has the implication of
making the subsystem menu visible in menuconfig. This is
happening because of two things:
- Intel have started to deploy and depend on pin controllers
in a way that is affecting users directly. This happens
on the highly integrated laptop chipsets named after
geographical places: baytrail, broxton, cannonlake,
cedarfork, cherryview, denverton, geminilake, lewisburg,
merrifield, sunrisepoint... It started a while back and
now it is ever more evident that this is crucial
infrastructure for x86 laptops and not an embedded
obscurity anymore. Users need to be aware.
- Pin control expanders on I2C and SPI that are
arch-agnostic. Currently Semtech SX150X and Microchip
MCP28x08 but more are expected. Users will have to be
able to configure these in directly for their set-up.
- Just go and select GPIOLIB now that we made sure that
GPIOLIB is a very vanilla subsystem. Do not depend on
it, if we need it, select it.
- Exposing the pin control subsystem in menuconfig uncovered
a bunch of obscure bugs that are now hopefully fixed,
all more or less pertaining to Blackfin.
- Unified namespace for cross-calls between pin control and
GPIO.
- New support for clock skew/delay generic DT bindings
and generic pin config options for this.
- Minor documentation improvements.
Various:
- The Renesas SH-PFC pin controller has evolved a lot. It seems
Renesas are churning out new SoCs by the minute.
- A bunch of non-critical fixes for the Rockchip driver.
- Improve the use of library functions instead of open coding.
- Support the MCP28018 variant in the MCP28x08 driver.
- Static constifying.
-----BEGIN PGP SIGNATURE-----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=kj/b
-----END PGP SIGNATURE-----
Merge tag 'pinctrl-v4.15-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control updates from Linus Walleij:
"This is the bulk of pin control changes for the v4.15 kernel cycle:
Core:
- The pin control Kconfig entry PINCTRL is now turned into a
menuconfig option. This obviously has the implication of making the
subsystem menu visible in menuconfig. This is happening because of
two things:
(a) Intel have started to deploy and depend on pin controllers in
a way that is affecting users directly. This happens on the
highly integrated laptop chipsets named after geographical
places: baytrail, broxton, cannonlake, cedarfork, cherryview,
denverton, geminilake, lewisburg, merrifield, sunrisepoint...
It started a while back and now it is ever more evident that
this is crucial infrastructure for x86 laptops and not an
embedded obscurity anymore. Users need to be aware.
(b) Pin control expanders on I2C and SPI that are arch-agnostic.
Currently Semtech SX150X and Microchip MCP28x08 but more are
expected. Users will have to be able to configure these in
directly for their set-up.
- Just go and select GPIOLIB now that we made sure that GPIOLIB is a
very vanilla subsystem. Do not depend on it, if we need it, select
it.
- Exposing the pin control subsystem in menuconfig uncovered a bunch
of obscure bugs that are now hopefully fixed, all more or less
pertaining to Blackfin.
- Unified namespace for cross-calls between pin control and GPIO.
- New support for clock skew/delay generic DT bindings and generic
pin config options for this.
- Minor documentation improvements.
Various:
- The Renesas SH-PFC pin controller has evolved a lot. It seems
Renesas are churning out new SoCs by the minute.
- A bunch of non-critical fixes for the Rockchip driver.
- Improve the use of library functions instead of open coding.
- Support the MCP28018 variant in the MCP28x08 driver.
- Static constifying"
* tag 'pinctrl-v4.15-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (91 commits)
pinctrl: gemini: Fix missing pad descriptions
pinctrl: Add some depends on HAS_IOMEM
pinctrl: samsung/s3c24xx: add CONFIG_OF dependency
pinctrl: gemini: Fix GMAC groups
pinctrl: qcom: spmi-gpio: Add pmi8994 gpio support
pinctrl: ti-iodelay: remove redundant unused variable dev
pinctrl: max77620: Use common error handling code in max77620_pinconf_set()
pinctrl: gemini: Implement clock skew/delay config
pinctrl: gemini: Use generic DT parser
pinctrl: Add skew-delay pin config and bindings
pinctrl: armada-37xx: Add edge both type gpio irq support
pinctrl: uniphier: remove eMMC hardware reset pin-mux
pinctrl: rockchip: Add iomux-route switching support for rk3288
pinctrl: intel: Add Intel Cedar Fork PCH pin controller support
pinctrl: intel: Make offset to interrupt status register configurable
pinctrl: sunxi: Enforce the strict mode by default
pinctrl: sunxi: Disable strict mode for old pinctrl drivers
pinctrl: sunxi: Introduce the strict flag
pinctrl: sh-pfc: Save/restore registers for PSCI system suspend
pinctrl: sh-pfc: r8a7796: Use generic IOCTRL register description
...
CORE:
- Fix the semantics of raw GPIO to actually be raw. No
inversion semantics as before, but also no open draining,
and allow the raw operations to affect lines used for
interrupts as the caller supposedly knows what they are
doing if they are getting the big hammer.
- Rewrote the __inner_function() notation calls to names that
make more sense. I just find this kind of code disturbing.
- Drop the .irq_base() field from the gpiochip since now all
IRQs are mapped dynamically. This is nice.
- Support for .get_multiple() in the core driver API. This
allows us to read several GPIO lines with a single
register read. This has high value for some usecases: it
can be used to create oscilloscopes and signal analyzers
and other things that rely on reading several lines at
exactly the same instant. Also a generally nice
optimization. This uses the new assign_bit() macro from
the bitops lib that was ACKed by Andrew Morton and
is implemented for two drivers, one of them being the
generic MMIO driver so everyone using that will be able
to benefit from this.
- Do not allow requests of Open Drain and Open Source
setting of a GPIO line simultaneously. If the hardware
actually supports enabling both at the same time the
electrical result would be disastrous.
- A new interrupt chip core helper. This will be helpful
to deal with "banked" GPIOs, which means GPIO controllers
with several logical blocks of GPIO inside them. This
is several gpiochips per device in the device model, in
contrast to the case when there is a 1-to-1 relationship
between a device and a gpiochip.
NEW DRIVERS:
- Maxim MAX3191x industrial serializer, a very interesting
piece of professional I/O hardware.
- Uniphier GPIO driver. This is the GPIO block from the
recent Socionext (ex Fujitsu and Panasonic) platform.
- Tegra 186 driver. This is based on the new banked GPIO
infrastructure.
OTHER IMPROVEMENTS:
- Some documentation improvements.
- Wakeup support for the DesignWare DWAPB GPIO controller.
- Reset line support on the DesignWare DWAPB GPIO controller.
- Several non-critical bug fixes and improvements for the
Broadcom BRCMSTB driver.
- Misc non-critical bug fixes like exotic errorpaths, removal
of dead code etc.
- Explicit comments on fall-through switch() statements.
-----BEGIN PGP SIGNATURE-----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=8Mon
-----END PGP SIGNATURE-----
Merge tag 'gpio-v4.15-1' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO updates from Linus Walleij:
"This is the bulk of GPIO changes for the v4.15 kernel cycle:
Core:
- Fix the semantics of raw GPIO to actually be raw. No inversion
semantics as before, but also no open draining, and allow the raw
operations to affect lines used for interrupts as the caller
supposedly knows what they are doing if they are getting the big
hammer.
- Rewrote the __inner_function() notation calls to names that make
more sense. I just find this kind of code disturbing.
- Drop the .irq_base() field from the gpiochip since now all IRQs are
mapped dynamically. This is nice.
- Support for .get_multiple() in the core driver API. This allows us
to read several GPIO lines with a single register read. This has
high value for some usecases: it can be used to create
oscilloscopes and signal analyzers and other things that rely on
reading several lines at exactly the same instant. Also a generally
nice optimization. This uses the new assign_bit() macro from the
bitops lib that was ACKed by Andrew Morton and is implemented for
two drivers, one of them being the generic MMIO driver so everyone
using that will be able to benefit from this.
- Do not allow requests of Open Drain and Open Source setting of a
GPIO line simultaneously. If the hardware actually supports
enabling both at the same time the electrical result would be
disastrous.
- A new interrupt chip core helper. This will be helpful to deal with
"banked" GPIOs, which means GPIO controllers with several logical
blocks of GPIO inside them. This is several gpiochips per device in
the device model, in contrast to the case when there is a 1-to-1
relationship between a device and a gpiochip.
New drivers:
- Maxim MAX3191x industrial serializer, a very interesting piece of
professional I/O hardware.
- Uniphier GPIO driver. This is the GPIO block from the recent
Socionext (ex Fujitsu and Panasonic) platform.
- Tegra 186 driver. This is based on the new banked GPIO
infrastructure.
Other improvements:
- Some documentation improvements.
- Wakeup support for the DesignWare DWAPB GPIO controller.
- Reset line support on the DesignWare DWAPB GPIO controller.
- Several non-critical bug fixes and improvements for the Broadcom
BRCMSTB driver.
- Misc non-critical bug fixes like exotic errorpaths, removal of dead
code etc.
- Explicit comments on fall-through switch() statements"
* tag 'gpio-v4.15-1' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (65 commits)
gpio: tegra186: Remove tegra186_gpio_lock_class
gpio: rcar: Add r8a77995 (R-Car D3) support
pinctrl: bcm2835: Fix some merge fallout
gpio: Fix undefined lock_dep_class
gpio: Automatically add lockdep keys
gpio: Introduce struct gpio_irq_chip.first
gpio: Disambiguate struct gpio_irq_chip.nested
gpio: Add Tegra186 support
gpio: Export gpiochip_irq_{map,unmap}()
gpio: Implement tighter IRQ chip integration
gpio: Move lock_key into struct gpio_irq_chip
gpio: Move irq_valid_mask into struct gpio_irq_chip
gpio: Move irq_nested into struct gpio_irq_chip
gpio: Move irq_chained_parent to struct gpio_irq_chip
gpio: Move irq_default_type to struct gpio_irq_chip
gpio: Move irq_handler to struct gpio_irq_chip
gpio: Move irqdomain into struct gpio_irq_chip
gpio: Move irqchip into struct gpio_irq_chip
gpio: Introduce struct gpio_irq_chip
pinctrl: armada-37xx: remove unused variable
...
In order to consolidate the multiple ways to associate an IRQ chip with
a GPIO chip, move more fields into the new struct gpio_irq_chip.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Acked-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
In order to consolidate the multiple ways to associate an IRQ chip with
a GPIO chip, move more fields into the new struct gpio_irq_chip.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Acked-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Intel Cedar Fork PCH is the successor of Intel Denverton PCH but it is
based on the newer GPIO/pinctrl hardware block. Add a new pinctrl/GPIO
driver to support it.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Some GPIO blocks have the interrupt status (GPI_IS) offset different
than it normally is, so make it configurable. If no offset is specified
we use the default.
While there remove two unused constants from the core driver.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Instead of depends on GPIOLIB and having to run around in
Kconfig menus looking for why your device is not available,
simply select it from the pin control drivers that need it.
The Kconfig for GPIOLIB is improved, selectable and this
should "just work".
Cc: Phil Reid <preid@electromag.com.au>
Cc: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Cc: Peter Rosin <peda@axentia.se>
Cc: Andrey Smirnov <andrew.smirnov@gmail.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
New GPIO IRQs are allocated and mapped dynamically by default when
GPIO IRQ infrastructure is used by cherryview-pinctrl driver.
This causes issues on some Intel platforms [1][2] with broken BIOS which
hardcodes Linux IRQ numbers in their ACPI tables.
On such platforms cherryview-pinctrl driver should allocate and map all
GPIO IRQs at probe time.
Side effect - "Cannot allocate irq_descs @ IRQ%d, assuming pre-allocated\n"
can be seen at boot log.
NOTE. It still may fail if boot sequence will changed and some interrupt
controller will be probed before cherryview-pinctrl which will shift Linux IRQ
numbering (expected with CONFIG_SPARCE_IRQ enabled).
[1] https://bugzilla.kernel.org/show_bug.cgi?id=194945
[2] https://lkml.org/lkml/2017/9/28/153
Cc: Andy Shevchenko <andy.shevchenko@gmail.com>
Cc: Chris Gorman <chrisjohgorman@gmail.com>
Cc: Mika Westerberg <mika.westerberg@linux.intel.com>
Cc: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Reported-by: Chris Gorman <chrisjohgorman@gmail.com>
Reported-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Tested-by: Chris Gorman <chrisjohgorman@gmail.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Fixed typo on comment for north_community.
Signed-off-by: Chris Gorman <chrisjohgorman@gmail.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
In the same way as it's done in pinctrl-cherryview.c we would provide
a readback TX buffer state.
Fixes: 17fab47369 ("pinctrl: intel: Set pin direction properly")
Reported-by: "Bourque, Francis" <francis.bourque@intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Tested-by: "Bourque, Francis" <francis.bourque@intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Decrease indentation in intel_gpio_set() to make it looking slightly better
and be in align with intel_gpio_get().
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Intel Lewisburg has the same GPIO hardware than Intel Sunrisepoint-H
except few differences in register offsets and pin lists. Because of
this we add a separate pinctrl driver for Lewisburg.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This is desktop version Intel Cannon Lake PCH. The GPIO hardware is the
same but pin list differs a bit. Add support for this to the existing
Cannon Lake pin controller driver.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The fix prevents unintended wakes from second level GPIO pin interrupts.
On some Intel Kabylake platforms, it is observed that GPIO pin interrupts
can wake the platform from suspend-to-idle, even though the IRQ is not
configured as IRQF_NO_SUSPEND or enable_irq_wake().
This can cause undesired wakes on Mobile devices such as Laptops and
Chromebook devices. For example a headset jack insertion is not a desired
wake source on Chromebook devices.
The pinctrl-intel (GPIO controller) driver implements a "Shared IRQ" model.
All GPIO pin interrupts are OR'ed and mapped to a first level IRQ14 (or
IRQ15). The driver registers an irq_chip struct and maps an irq_domain for
the GPIO pin interrupts. The IRQ14 handler demuxes and calls the second
level IRQ for the respective pin.
In the suspend entry flow, at suspend_noirq stage, the kernel disables IRQs
that are not marked for wake. The pinctrl-intel driver does not implement a
irq_disable() callback (to take advantage of lazy disabling). The
pinctrl-intel GPIO interrupts are not disabled in hardware during suspend
entry, and thus are able to wake the SoC out of suspend-to-idle.
This patch sets the IRQCHIP_MASK_ON_SUSPEND flag for the GPIO irq_chip, to
disable the second level interrupts at suspend_noirq stage via the irq_mask
callbacks. The irq_mask callback disables the IRQs in hardware by
programming the corresponding GPIO pad registers. Only IRQs that are not
marked for wake are disabled.
Signed-off-by: Rushikesh S Kadam <rushikesh.s.kadam@intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-and-tested-by: Rajneesh Bhardwaj <rajneesh.bhardwaj@intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This driver adds pinctrl/GPIO support for Intel Denverton SoC. The GPIO
controller is based on the same hardware design that is already used in
Intel Sunrisepoint so we leverage the core driver here.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The Intel pin control drivers are architecture specific so add an if arch
to check for X86 or compile test to ensure continued test coverage.
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
WARN_ON causes a backtrace to get logged which is only useful for
kernel bugs. For signalling a firmware bug dev_warn(dev, FW_BUG "...")
should be used.
This fixes users running userspace software to monitor kernel oopses
getting a false positive bug-report every boot because of the wrong
use of WARN_ON.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add one more model to the Chromebook DMI quirk to make it working again.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=194945
Fixes: 2a8209fa68 ("pinctrl: cherryview: Extend the Chromebook DMI quirk to Intel_Strago systems")
Reported-by: mail@abhishek.geek.nz
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This adds pinctrl/GPIO support for Intel Cannon Lake PCH. The Cannon
Lake PCH GPIO is based on newer version of the Intel GPIO hardware.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
On some SoCs not all pins in a group use the same mode when a certain
function is muxed out of them. This makes it possible to specify mode per
pin as an array instead in addition to single integer.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The Intel GPIO hardware has a concept of pad groups, which means 1 to 32
pads occupying their own GPI_IS, GPI_IE, PAD_OWN and so on registers. The
existing hardware has the same amount of pads in each pad group (except the
last one) so it is possible to use community->gpp_size to calculate start
offset of each register.
With the next generation SoCs the pad group size is not always the same
anymore which means we cannot use community->gpp_size for register offset
calculations directly.
To support variable size pad groups we introduce struct intel_padgroup that
can be filled in by the client drivers according the hardware pad group
layout. The core driver will always use these when it performs calculations
for pad register offsets. The core driver will automatically populate pad
groups based on community->gpp_size if the driver does not provide any.
This makes sure the existing drivers still work as expected.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Chuah, Kim Tatt <kim.tatt.chuah@intel.com>
Signed-off-by: Tan Jui Nee <jui.nee.tan@intel.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Dmitry Torokhov
Andy Shevchenko
Linus Torvalds
Linus Walleij
Arnd Bergmann
Chris Chiu
Stephen Boyd
Kai-Heng Feng
Binbin Wu
Aditya Pakki
Hans de Goede
Wolfram Sang
Mika Westerberg
Simon Detheridge
Alexander Stein
Gustavo A. R. Silva
Randy Dunlap
Javier Arteaga
Colin Ian King
Thierry Reding
Greg Kroah-Hartman
Grygorii Strashko
Chris Gorman
Rushikesh S Kadam
Peter Robinson