Pull block layer fixes from Jens Axboe:
"Two smaller fixes for this cycle:
- A fixup from Keith so that NVMe compiles without BLK_INTEGRITY,
basically just moving the code around appropriately.
- A fixup for shm, fixing an oops in shmem_mapping() for mapping with
no inode. From Sasha"
[ The shmem fix doesn't look block-layer-related, but fixes a bug that
happened due to the backing_dev_info removal.. - Linus ]
* 'for-linus' of git://git.kernel.dk/linux-block:
mm: shmem: check for mapping owner before dereferencing
NVMe: Fix for BLK_DEV_INTEGRITY not set
max_used_pages is defined as atomic_long_t so we need to use unsigned
long to keep temporary value for it rather than int which is smaller
than unsigned long in a 64 bit system.
Signed-off-by: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Cc: Minchan Kim <minchan@kernel.org>
Cc: Jerome Marchand <jmarchan@redhat.com>
Cc: Nitin Gupta <ngupta@vflare.org>
Cc: Sergey Senozhatsky <sergey.senozhatsky.work@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Need to define and use appropriate functions for when BLK_DEV_INTEGRITY
is not set.
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
This makes all sync commands uninterruptible and schedules without timeout
so the controller either has to post a completion or the timeout recovery
fails the command. This fixes potential memory or data corruption from
a command timing out too early or woken by a signal. Previously any DMA
buffers mapped for that command would have been released even though we
don't know what the controller is planning to do with those addresses.
Signed-off-by: Keith Busch <keith.busch@intel.com>
We don't track queues in a llist, subscribe to hot-cpu notifications,
or internally retry commands. Delete the unused artifacts.
Signed-off-by: Keith Busch <keith.busch@intel.com>
The driver has to end unreturned commands at some point even if the
controller has not provided a completion. The driver tried to be safe by
deleting IO queues prior to ending all unreturned commands. That should
cause the controller to internally abort inflight commands, but IO queue
deletion request does not have to be successful, so all bets are off. We
still have to make progress, so to be extra safe, this patch doesn't
clear a queue to release the dma mapping for a command until after the
pci device has been disabled.
This patch removes the special handling during device initialization
so controller recovery can be done all the time. This is possible since
initialization is not inlined with pci probe anymore.
Reported-by: Nilish Choudhury <nilesh.choudhury@oracle.com>
Signed-off-by: Keith Busch <keith.busch@intel.com>
This performs the longest parts of nvme device probe in scheduled work.
This speeds up probe significantly when multiple devices are in use.
Signed-off-by: Keith Busch <keith.busch@intel.com>
This creates a new class type for nvme devices to register their
management character devices with. This is so we do not rely on miscdev
to provide enough minors for as many nvme devices some people plan to
use. The previous limit was approximately 60 NVMe controllers, depending
on the platform and kernel. Now the limit is 1M, which ought to be enough
for anybody.
Since we have a new device class, it makes sense to attach the block
devices under this as well, so part of this patch moves the management
handle initialization prior to the namespaces discovery.
Signed-off-by: Keith Busch <keith.busch@intel.com>
The original translation created collisions on Inquiry VPD 83 for many
existing devices. Newer specifications provide other ways to translate
based on the device's version can be used to create unique identifiers.
Version 1.1 provides an EUI64 field that uniquely identifies each
namespace, and 1.2 added the longer NGUID field for the same reason.
Both follow the IEEE EUI format and readily translate to the SCSI device
identification EUI designator type 2h. For devices implementing either,
the translation will use this type, defaulting to the EUI64 8-byte type if
implemented then NGUID's 16 byte version if not. If neither are provided,
the 1.0 translation is used, and is updated to use the SCSI String format
to guarantee a unique identifier.
Knowing when to use the new fields depends on the nvme controller's
revision. The NVME_VS macro was not decoding this correctly, so that is
fixed in this patch and moved to a more appropriate place.
Since the Identify Namespace structure required an update for the NGUID
field, this patch adds the remaining new 1.2 fields to the structure.
Signed-off-by: Keith Busch <keith.busch@intel.com>
Adds support for NVMe metadata formats and exposes block devices for
all namespaces regardless of their format. Namespace formats that are
unusable will have disk capacity set to 0, but a handle to the block
device is created to simplify device management. A namespace is not
usable when the format requires host interleave block and metadata in
single buffer, has no provisioned storage, or has better data but failed
to register with blk integrity.
The namespace has to be scanned in two phases to support separate
metadata formats. The first establishes the sector size and capacity
prior to invoking add_disk. If metadata is required, the capacity will
be temporarilly set to 0 until it can be revalidated and registered with
the integrity extenstions after add_disk completes.
The driver relies on the integrity extensions to provide the metadata
buffer. NVMe requires this be a single physically contiguous region,
so only one integrity segment is allowed per command. If the metadata
is used for T10 PI, the driver provides mappings to save and restore
the reftag physical block translation. The driver provides no-op
functions for generate and verify if metadata is not used for protection
information. This way the setup is always provided by the block layer.
If a request does not supply a required metadata buffer, the command
is failed with bad address. This could only happen if a user manually
disables verify/generate on such a disk. The only exception to where
this is okay is if the controller is capable of stripping/generating
the metadata, which is possible on some types of formats.
The metadata scatter gather list now occupies the spot in the nvme_iod
that used to be used to link retryable IOD's, but we don't do that
anymore, so the field was unused.
Signed-off-by: Keith Busch <keith.busch@intel.com>
Pull Ceph changes from Sage Weil:
"On the RBD side, there is a conversion to blk-mq from Christoph,
several long-standing bug fixes from Ilya, and some cleanup from
Rickard Strandqvist.
On the CephFS side there is a long list of fixes from Zheng, including
improved session handling, a few IO path fixes, some dcache management
correctness fixes, and several blocking while !TASK_RUNNING fixes.
The core code gets a few cleanups and Chaitanya has added support for
TCP_NODELAY (which has been used on the server side for ages but we
somehow missed on the kernel client).
There is also an update to MAINTAINERS to fix up some email addresses
and reflect that Ilya and Zheng are doing most of the maintenance for
RBD and CephFS these days. Do not be surprised to see a pull request
come from one of them in the future if I am unavailable for some
reason"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/sage/ceph-client: (27 commits)
MAINTAINERS: update Ceph and RBD maintainers
libceph: kfree() in put_osd() shouldn't depend on authorizer
libceph: fix double __remove_osd() problem
rbd: convert to blk-mq
ceph: return error for traceless reply race
ceph: fix dentry leaks
ceph: re-send requests when MDS enters reconnecting stage
ceph: show nocephx_require_signatures and notcp_nodelay options
libceph: tcp_nodelay support
rbd: do not treat standalone as flatten
ceph: fix atomic_open snapdir
ceph: properly mark empty directory as complete
client: include kernel version in client metadata
ceph: provide seperate {inode,file}_operations for snapdir
ceph: fix request time stamp encoding
ceph: fix reading inline data when i_size > PAGE_SIZE
ceph: avoid block operation when !TASK_RUNNING (ceph_mdsc_close_sessions)
ceph: avoid block operation when !TASK_RUNNING (ceph_get_caps)
ceph: avoid block operation when !TASK_RUNNING (ceph_mdsc_sync)
rbd: fix error paths in rbd_dev_refresh()
...
This converts the rbd driver to use the blk-mq infrastructure. Except
for switching to a per-request work item this is almost mechanical.
This was tested by Alexandre DERUMIER in November, and found to give
him 120000 iops, although the only comparism available was an old
3.10 kernel which gave 80000iops.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Alex Elder <elder@linaro.org>
[idryomov@gmail.com: context, blk_mq_init_queue() EH]
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
If the clone is resized down to 0, it becomes standalone. If such
resize is carried over while an image is mapped we would detect this
and call rbd_dev_parent_put() which means "let go of all parent state,
including the spec(s) of parent images(s)". This leads to a mismatch
between "rbd info" and sysfs parent fields, so a fix is in order.
# rbd create --image-format 2 --size 1 foo
# rbd snap create foo@snap
# rbd snap protect foo@snap
# rbd clone foo@snap bar
# DEV=$(rbd map bar)
# rbd resize --allow-shrink --size 0 bar
# rbd resize --size 1 bar
# rbd info bar | grep parent
parent: rbd/foo@snap
Before:
# cat /sys/bus/rbd/devices/0/parent
(no parent image)
After:
# cat /sys/bus/rbd/devices/0/parent
pool_id 0
pool_name rbd
image_id 10056b8b4567
image_name foo
snap_id 2
snap_name snap
overlap 0
Signed-off-by: Ilya Dryomov <idryomov@redhat.com>
Reviewed-by: Josh Durgin <jdurgin@redhat.com>
Reviewed-by: Alex Elder <elder@linaro.org>
header_rwsem should be released on errors. Also remove useless
rbd_dev->mapping.size != rbd_dev->header.image_size test.
Signed-off-by: Ilya Dryomov <idryomov@redhat.com>
It's been largely superseded by dup_token() and unused for over
2 years, identified by cppcheck.
Signed-off-by: Rickard Strandqvist <rickard_strandqvist@spectrumdigital.se>
[idryomov@redhat.com: changelog]
Signed-off-by: Ilya Dryomov <idryomov@redhat.com>
On top of tht is the major rework of lguest, to use PCI and virtio 1.0, to
double-check the implementation.
Then comes the inevitable fixes and cleanups from that work.
Thanks,
Rusty.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=ivCe
-----END PGP SIGNATURE-----
Merge tag 'virtio-next-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux
Pull virtio updates from Rusty Russell:
"OK, this has the big virtio 1.0 implementation, as specified by OASIS.
On top of tht is the major rework of lguest, to use PCI and virtio
1.0, to double-check the implementation.
Then comes the inevitable fixes and cleanups from that work"
* tag 'virtio-next-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux: (80 commits)
virtio: don't set VIRTIO_CONFIG_S_DRIVER_OK twice.
virtio_net: unconditionally define struct virtio_net_hdr_v1.
tools/lguest: don't use legacy definitions for net device in example launcher.
virtio: Don't expose legacy net features when VIRTIO_NET_NO_LEGACY defined.
tools/lguest: use common error macros in the example launcher.
tools/lguest: give virtqueues names for better error messages
tools/lguest: more documentation and checking of virtio 1.0 compliance.
lguest: don't look in console features to find emerg_wr.
tools/lguest: don't start devices until DRIVER_OK status set.
tools/lguest: handle indirect partway through chain.
tools/lguest: insert driver references from the 1.0 spec (4.1 Virtio Over PCI)
tools/lguest: insert device references from the 1.0 spec (4.1 Virtio Over PCI)
tools/lguest: rename virtio_pci_cfg_cap field to match spec.
tools/lguest: fix features_accepted logic in example launcher.
tools/lguest: handle device reset correctly in example launcher.
virtual: Documentation: simplify and generalize paravirt_ops.txt
lguest: remove NOTIFY call and eventfd facility.
lguest: remove NOTIFY facility from demonstration launcher.
lguest: use the PCI console device's emerg_wr for early boot messages.
lguest: always put console in PCI slot #1.
...
Since this is relating to FS_XIP, not KERNEL_XIP, it should be called
DAX instead of XIP.
Signed-off-by: Matthew Wilcox <matthew.r.wilcox@intel.com>
Cc: Andreas Dilger <andreas.dilger@intel.com>
Cc: Boaz Harrosh <boaz@plexistor.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Dave Chinner <david@fromorbit.com>
Cc: Jan Kara <jack@suse.cz>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Cc: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Cc: Randy Dunlap <rdunlap@infradead.org>
Cc: Ross Zwisler <ross.zwisler@linux.intel.com>
Cc: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Merge third set of updates from Andrew Morton:
- the rest of MM
[ This includes getting rid of the numa hinting bits, in favor of
just generic protnone logic. Yay. - Linus ]
- core kernel
- procfs
- some of lib/ (lots of lib/ material this time)
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (104 commits)
lib/lcm.c: replace include
lib/percpu_ida.c: remove redundant includes
lib/strncpy_from_user.c: replace module.h include
lib/stmp_device.c: replace module.h include
lib/sort.c: move include inside #if 0
lib/show_mem.c: remove redundant include
lib/radix-tree.c: change to simpler include
lib/plist.c: remove redundant include
lib/nlattr.c: remove redundant include
lib/kobject_uevent.c: remove redundant include
lib/llist.c: remove redundant include
lib/md5.c: simplify include
lib/list_sort.c: rearrange includes
lib/genalloc.c: remove redundant include
lib/idr.c: remove redundant include
lib/halfmd4.c: simplify includes
lib/dynamic_queue_limits.c: simplify includes
lib/sort.c: use simpler includes
lib/interval_tree.c: simplify includes
hexdump: make it return number of bytes placed in buffer
...
__FUNCTION__ hasn't been treated as a string literal since gcc 3.4, so
this only helps people who only test-compile using 3.3 (compiler-gcc3.h
barks at anything older than that). Besides, there are almost no
occurrences of __FUNCTION__ left in the tree.
[akpm@linux-foundation.org: convert remaining __FUNCTION__ references]
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Cc: Michal Nazarewicz <mina86@mina86.com>
Cc: Joe Perches <joe@perches.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Currently the underlay of zpool: zsmalloc/zbud, do not know who creates
them. There is not a method to let zsmalloc/zbud find which caller they
belong to.
Now we want to add statistics collection in zsmalloc. We need to name the
debugfs dir for each pool created. The way suggested by Minchan Kim is to
use a name passed by caller(such as zram) to create the zsmalloc pool.
/sys/kernel/debug/zsmalloc/zram0
This patch adds an argument `name' to zs_create_pool() and other related
functions.
Signed-off-by: Ganesh Mahendran <opensource.ganesh@gmail.com>
Acked-by: Minchan Kim <minchan@kernel.org>
Cc: Seth Jennings <sjennings@variantweb.net>
Cc: Nitin Gupta <ngupta@vflare.org>
Cc: Dan Streetman <ddstreet@ieee.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
`struct zram' contains both `struct gendisk' and `struct request_queue'.
the latter can be deleted, because zram->disk carries ->queue pointer, and
->queue carries zram pointer:
create_device()
zram->queue->queuedata = zram
zram->disk->queue = zram->queue
zram->disk->private_data = zram
so zram->queue is not needed, we can access all necessary data anyway.
Signed-off-by: Sergey Senozhatsky <sergey.senozhatsky@gmail.com>
Cc: Minchan Kim <minchan@kernel.org>
Cc: Jerome Marchand <jmarchan@redhat.com>
Cc: Nitin Gupta <ngupta@vflare.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Admin could reset zram during I/O operation going on so we have used
zram->init_lock as read-side lock in I/O path to prevent sudden zram
meta freeing.
However, the init_lock is really troublesome. We can't do call
zram_meta_alloc under init_lock due to lockdep splat because
zram_rw_page is one of the function under reclaim path and hold it as
read_lock while other places in process context hold it as write_lock.
So, we have used allocation out of the lock to avoid lockdep warn but
it's not good for readability and fainally, I met another lockdep splat
between init_lock and cpu_hotplug from kmem_cache_destroy during working
zsmalloc compaction. :(
Yes, the ideal is to remove horrible init_lock of zram in rw path. This
patch removes it in rw path and instead, add atomic refcount for meta
lifetime management and completion to free meta in process context.
It's important to free meta in process context because some of resource
destruction needs mutex lock, which could be held if we releases the
resource in reclaim context so it's deadlock, again.
As a bonus, we could remove init_done check in rw path because
zram_meta_get will do a role for it, instead.
Signed-off-by: Sergey Senozhatsky <sergey.senozhatsky@gmail.com>
Signed-off-by: Minchan Kim <minchan@kernel.org>
Cc: Nitin Gupta <ngupta@vflare.org>
Cc: Jerome Marchand <jmarchan@redhat.com>
Cc: Ganesh Mahendran <opensource.ganesh@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
bd_holders is increased only when user open the device file as FMODE_EXCL
so if something opens zram0 as !FMODE_EXCL and request I/O while another
user reset zram0, we can see following warning.
zram0: detected capacity change from 0 to 64424509440
Buffer I/O error on dev zram0, logical block 180823, lost async page write
Buffer I/O error on dev zram0, logical block 180824, lost async page write
Buffer I/O error on dev zram0, logical block 180825, lost async page write
Buffer I/O error on dev zram0, logical block 180826, lost async page write
Buffer I/O error on dev zram0, logical block 180827, lost async page write
Buffer I/O error on dev zram0, logical block 180828, lost async page write
Buffer I/O error on dev zram0, logical block 180829, lost async page write
Buffer I/O error on dev zram0, logical block 180830, lost async page write
Buffer I/O error on dev zram0, logical block 180831, lost async page write
Buffer I/O error on dev zram0, logical block 180832, lost async page write
------------[ cut here ]------------
WARNING: CPU: 11 PID: 1996 at fs/block_dev.c:57 __blkdev_put+0x1d7/0x210()
Modules linked in:
CPU: 11 PID: 1996 Comm: dd Not tainted 3.19.0-rc6-next-20150202+ #1125
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS Bochs 01/01/2011
Call Trace:
dump_stack+0x45/0x57
warn_slowpath_common+0x8a/0xc0
warn_slowpath_null+0x1a/0x20
__blkdev_put+0x1d7/0x210
blkdev_put+0x50/0x130
blkdev_close+0x25/0x30
__fput+0xdf/0x1e0
____fput+0xe/0x10
task_work_run+0xa7/0xe0
do_notify_resume+0x49/0x60
int_signal+0x12/0x17
---[ end trace 274fbbc5664827d2 ]---
The warning comes from bdev_write_node in blkdev_put path.
static void bdev_write_inode(struct inode *inode)
{
spin_lock(&inode->i_lock);
while (inode->i_state & I_DIRTY) {
spin_unlock(&inode->i_lock);
WARN_ON_ONCE(write_inode_now(inode, true)); <========= here.
spin_lock(&inode->i_lock);
}
spin_unlock(&inode->i_lock);
}
The reason is dd process encounters I/O fails due to sudden block device
disappear so in filemap_check_errors in __writeback_single_inode returns
-EIO.
If we check bd_openers instead of bd_holders, we could address the
problem. When I see the brd, it already have used it rather than
bd_holders so although I'm not a expert of block layer, it seems to be
better.
I can make following warning with below simple script. In addition, I
added msleep(2000) below set_capacity(zram->disk, 0) after applying your
patch to make window huge(Kudos to Ganesh!)
script:
echo $((60<<30)) > /sys/block/zram0/disksize
setsid dd if=/dev/zero of=/dev/zram0 &
sleep 1
setsid echo 1 > /sys/block/zram0/reset
Signed-off-by: Minchan Kim <minchan@kernel.org>
Acked-by: Sergey Senozhatsky <sergey.senozhatsky@gmail.com>
Cc: Nitin Gupta <ngupta@vflare.org>
Cc: Jerome Marchand <jmarchan@redhat.com>
Cc: Ganesh Mahendran <opensource.ganesh@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
We need to return set_capacity(disk, 0) from reset_store() back to
zram_reset_device(), a catch by Ganesh Mahendran. Potentially, we can
race set_capacity() calls from init and reset paths.
The problem is that zram_reset_device() is also getting called from
zram_exit(), which performs operations in misleading reversed order -- we
first create_device() and then init it, while zram_exit() perform
destroy_device() first and then does zram_reset_device(). This is done to
remove sysfs group before we reset device, so we can continue with device
reset/destruction not being raced by sysfs attr write (f.e. disksize).
Apart from that, destroy_device() releases zram->disk (but we still have
->disk pointer), so we cannot acces zram->disk in later
zram_reset_device() call, which may cause additional errors in the future.
So, this patch rework and cleanup destroy path.
1) remove several unneeded goto labels in zram_init()
2) factor out zram_init() error path and zram_exit() into
destroy_devices() function, which takes the number of devices to
destroy as its argument.
3) remove sysfs group in destroy_devices() first, so we can reorder
operations -- reset device (as expected) goes before disk destroy and
queue cleanup. So we can always access ->disk in zram_reset_device().
4) and, finally, return set_capacity() back under ->init_lock.
[akpm@linux-foundation.org: tweak comment]
Signed-off-by: Sergey Senozhatsky <sergey.senozhatsky@gmail.com>
Reported-by: Ganesh Mahendran <opensource.ganesh@gmail.com>
Cc: Minchan Kim <minchan@kernel.org>
Cc: Jerome Marchand <jmarchan@redhat.com>
Cc: Nitin Gupta <ngupta@vflare.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Ganesh Mahendran was the first one who proposed to use bdev->bd_mutex to
avoid ->bd_holders race condition:
CPU0 CPU1
umount /* zram->init_done is true */
reset_store()
bdev->bd_holders == 0 mount
... zram_make_request()
zram_reset_device()
However, his solution required some considerable amount of code movement,
which we can avoid.
Apart from using bdev->bd_mutex in reset_store(), this patch also
simplifies zram_reset_device().
zram_reset_device() has a bool parameter reset_capacity which tells it
whether disk capacity and itself disk should be reset. There are two
zram_reset_device() callers:
-- zram_exit() passes reset_capacity=false
-- reset_store() passes reset_capacity=true
So we can move reset_capacity-sensitive work out of zram_reset_device()
and perform it unconditionally in reset_store(). This also lets us drop
reset_capacity parameter from zram_reset_device() and pass zram pointer
only.
Signed-off-by: Sergey Senozhatsky <sergey.senozhatsky@gmail.com>
Reported-by: Ganesh Mahendran <opensource.ganesh@gmail.com>
Cc: Minchan Kim <minchan@kernel.org>
Cc: Vlastimil Babka <vbabka@suse.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
zram_meta_alloc() and zram_meta_free() are a pair. In
zram_meta_alloc(), meta table is allocated. So it it better to free it
in zram_meta_free().
Signed-off-by: Ganesh Mahendran <opensource.ganesh@gmail.com>
Acked-by: Minchan Kim <minchan@kernel.org>
Acked-by: Sergey Senozhatsky <sergey.senozhatsky@gmail.com>
Cc: Nitin Gupta <ngupta@vflare.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull block driver changes from Jens Axboe:
"This contains:
- The 4k/partition fixes for brd from Boaz/Matthew.
- A few xen front/back block fixes from David Vrabel and Roger Pau
Monne.
- Floppy changes from Takashi, cleaning the device file creation.
- Switching libata to use the new blk-mq tagging policy, removing
code (and a suboptimal implementation) from libata. This will
throw you a merge conflict, since a bug in the original libata
tagging code was fixed since this code was branched. Trivial.
From Shaohua.
- Conversion of loop to blk-mq, from Ming Lei.
- Cleanup of the io_schedule() handling in bsg from Peter Zijlstra.
He claims it improves on unreadable code, which will cost him a
beer.
- Maintainer update or NDB, now handled by Markus Pargmann.
- NVMe:
- Optimization from me that avoids a kmalloc/kfree per IO for
smaller (<= 8KB) IO. This cuts about 1% of high IOPS CPU
overhead.
- Removal of (now) dead RCU code, a relic from before NVMe was
converted to blk-mq"
* 'for-3.20/drivers' of git://git.kernel.dk/linux-block:
xen-blkback: default to X86_32 ABI on x86
xen-blkfront: fix accounting of reqs when migrating
xen-blkback,xen-blkfront: add myself as maintainer
block: Simplify bsg complete all
floppy: Avoid manual call of device_create_file()
NVMe: avoid kmalloc/kfree for smaller IO
MAINTAINERS: Update NBD maintainer
libata: make sata_sil24 use fifo tag allocator
libata: move sas ata tag allocation to libata-scsi.c
libata: use blk taging
NVMe: within nvme_free_queues(), delete RCU sychro/deferred free
null_blk: suppress invalid partition info
brd: Request from fdisk 4k alignment
brd: Fix all partitions BUGs
axonram: Fix bug in direct_access
loop: add blk-mq.h include
block: loop: don't handle REQ_FUA explicitly
block: loop: introduce lo_discard() and lo_req_flush()
block: loop: say goodby to bio
block: loop: improve performance via blk-mq
Pull core block IO changes from Jens Axboe:
"This contains:
- A series from Christoph that cleans up and refactors various parts
of the REQ_BLOCK_PC handling. Contributions in that series from
Dongsu Park and Kent Overstreet as well.
- CFQ:
- A bug fix for cfq for realtime IO scheduling from Jeff Moyer.
- A stable patch fixing a potential crash in CFQ in OOM
situations. From Konstantin Khlebnikov.
- blk-mq:
- Add support for tag allocation policies, from Shaohua. This is
a prep patch enabling libata (and other SCSI parts) to use the
blk-mq tagging, instead of rolling their own.
- Various little tweaks from Keith and Mike, in preparation for
DM blk-mq support.
- Minor little fixes or tweaks from me.
- A double free error fix from Tony Battersby.
- The partition 4k issue fixes from Matthew and Boaz.
- Add support for zero+unprovision for blkdev_issue_zeroout() from
Martin"
* 'for-3.20/core' of git://git.kernel.dk/linux-block: (27 commits)
block: remove unused function blk_bio_map_sg
block: handle the null_mapped flag correctly in blk_rq_map_user_iov
blk-mq: fix double-free in error path
block: prevent request-to-request merging with gaps if not allowed
blk-mq: make blk_mq_run_queues() static
dm: fix multipath regression due to initializing wrong request
cfq-iosched: handle failure of cfq group allocation
block: Quiesce zeroout wrapper
block: rewrite and split __bio_copy_iov()
block: merge __bio_map_user_iov into bio_map_user_iov
block: merge __bio_map_kern into bio_map_kern
block: pass iov_iter to the BLOCK_PC mapping functions
block: add a helper to free bio bounce buffer pages
block: use blk_rq_map_user_iov to implement blk_rq_map_user
block: simplify bio_map_kern
block: mark blk-mq devices as stackable
block: keep established cmd_flags when cloning into a blk-mq request
block: add blk-mq support to blk_insert_cloned_request()
block: require blk_rq_prep_clone() be given an initialized clone request
blk-mq: add tag allocation policy
...
- Reworked handling for foreign (grant mapped) pages to simplify the
code, enable a number of additional use cases and fix a number of
long-standing bugs.
- Prefer the TSC over the Xen PV clock when dom0 (and the TSC is
stable).
- Assorted other cleanup and minor bug fixes.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)
iQEcBAABAgAGBQJU2JC+AAoJEFxbo/MsZsTRIvAH/1lgQ0EQlxaZtEFWY8cJBzxY
dXaTMfyGQOddGYDCW0r42hhXJHeX7DWXSERSD3aW9DZOn/eYdneHq9gWRD4uPrGn
hEFQ26J4jZWR5riGXaja0LqI2gJKLZ6BhHIQciLEbY+jw4ynkNBLNRPFehuwrCsZ
WdBwJkyvXC3RErekncRl/aNhxdi4p1P6qeiaW/mo3UcSO/CFSKybOLwT65iePazg
XuY9UiTn2+qcRkm/tjx8K9heHK8SBEGNWuoTcWYF1to8mwwUfKIAc4NO2UBDXJI+
rp7Z2lVFdII15JsQ08ATh3t7xDrMWLzCX/y4jCzmF3DBXLbSWdHCQMgI7TWt5pE=
=PyJK
-----END PGP SIGNATURE-----
Merge tag 'stable/for-linus-3.20-rc0-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip
Pull xen features and fixes from David Vrabel:
- Reworked handling for foreign (grant mapped) pages to simplify the
code, enable a number of additional use cases and fix a number of
long-standing bugs.
- Prefer the TSC over the Xen PV clock when dom0 (and the TSC is
stable).
- Assorted other cleanup and minor bug fixes.
* tag 'stable/for-linus-3.20-rc0-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip: (25 commits)
xen/manage: Fix USB interaction issues when resuming
xenbus: Add proper handling of XS_ERROR from Xenbus for transactions.
xen/gntdev: provide find_special_page VMA operation
xen/gntdev: mark userspace PTEs as special on x86 PV guests
xen-blkback: safely unmap grants in case they are still in use
xen/gntdev: safely unmap grants in case they are still in use
xen/gntdev: convert priv->lock to a mutex
xen/grant-table: add a mechanism to safely unmap pages that are in use
xen-netback: use foreign page information from the pages themselves
xen: mark grant mapped pages as foreign
xen/grant-table: add helpers for allocating pages
x86/xen: require ballooned pages for grant maps
xen: remove scratch frames for ballooned pages and m2p override
xen/grant-table: pre-populate kernel unmap ops for xen_gnttab_unmap_refs()
mm: add 'foreign' alias for the 'pinned' page flag
mm: provide a find_special_page vma operation
x86/xen: cleanup arch/x86/xen/mmu.c
x86/xen: add some __init annotations in arch/x86/xen/mmu.c
x86/xen: add some __init and static annotations in arch/x86/xen/setup.c
x86/xen: use correct types for addresses in arch/x86/xen/setup.c
...
Prior to the existance of 64-bit backends using the X86_64 ABI,
frontends used the X86_32 ABI. These old frontends do not specify the
ABI and when used with a 64-bit backend do not work.
On x86, default to the X86_32 ABI if one is not specified. Backends
on ARM continue to default to their NATIVE ABI.
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
Acked-by: Roger Pau Monné <roger.pau@citrix.com>
Current migration code uses blk_put_request in order to finish a request
before requeuing it. This function doesn't update the statistics of the
queue, which completely screws accounting. Use blk_end_request_all instead
which properly updates the statistics of the queue.
Signed-off-by: Roger Pau Monné <roger.pau@citrix.com>
Reported-and-Tested-by: Ouyang Zhaowei (Charles) <ouyangzhaowei@huawei.com>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Cc: David Vrabel <david.vrabel@citrix.com>
Cc: xen-devel@lists.xenproject.org
Use the static attribute groups assigned to the device instead of
calling device_create_file() after the device registration.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Currently we allocate an nvme_iod for each IO, which holds the
sg list, prps, and other IO related info. Set a threshold of
2 pages and/or 8KB of data, below which we can just embed this
in the per-command pdu in blk-mq. For any IO at or below
NVME_INT_PAGES and NVME_INT_BYTES, we save a kmalloc and kfree.
For higher IOPS, this saves up to 1% of CPU time.
Signed-off-by: Jens Axboe <axboe@fb.com>
Reviewed-by: Keith Busch <keith.busch@intel.com>
Use gnttab_unmap_refs_async() to wait until the mapped pages are no
longer in use before unmapping them.
This allows blkback to use network storage which may retain refs to
pages in queued skbs after the block I/O has completed.
Signed-off-by: Jennifer Herbert <jennifer.herbert@citrix.com>
Acked-by: Roger Pau Monné <roger.pau@citrix.com>
Acked-by: Jens Axboe <axboe@kernel.de>
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
Add gnttab_alloc_pages() and gnttab_free_pages() to allocate/free pages
suitable to for granted maps.
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
Reviewed-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
This effectively reverts the last hunk of 392a9dad7e ("rbd: detect
when clone image is flattened").
The problem with parent_overlap != 0 condition is that it's possible
and completely valid to have an image with parent_overlap == 0 whose
parent state needs to be cleaned up on unmap. The next commit, which
drops the "clone image now standalone" logic, opens up another window
of opportunity to hit this, but even without it
# cat parent-ref.sh
#!/bin/bash
rbd create --image-format 2 --size 1 foo
rbd snap create foo@snap
rbd snap protect foo@snap
rbd clone foo@snap bar
rbd resize --allow-shrink --size 0 bar
rbd resize --size 1 bar
DEV=$(rbd map bar)
rbd unmap $DEV
leaves rbd_device/rbd_spec/etc and rbd_client along with ceph_client
hanging around.
My thinking behind calling rbd_dev_parent_put() unconditionally is that
there shouldn't be any requests in flight at that point in time as we
are deep into unmap sequence. Hence, even if rbd_dev_unparent() caused
by flatten is delayed by in-flight requests, it will have finished by
the time we reach rbd_dev_unprobe() caused by unmap, thus turning
unconditional rbd_dev_parent_put() into a no-op.
Fixes: http://tracker.ceph.com/issues/10352
Cc: stable@vger.kernel.org # 3.11+
Signed-off-by: Ilya Dryomov <idryomov@redhat.com>
Reviewed-by: Josh Durgin <jdurgin@redhat.com>
Reviewed-by: Alex Elder <elder@linaro.org>
The comment for rbd_dev_parent_get() said
* We must get the reference before checking for the overlap to
* coordinate properly with zeroing the parent overlap in
* rbd_dev_v2_parent_info() when an image gets flattened. We
* drop it again if there is no overlap.
but the "drop it again if there is no overlap" part was missing from
the implementation. This lead to absurd parent_ref values for images
with parent_overlap == 0, as parent_ref was incremented for each
img_request and virtually never decremented.
Fix this by leveraging the fact that refresh path calls
rbd_dev_v2_parent_info() under header_rwsem and use it for read in
rbd_dev_parent_get(), instead of messing around with atomics. Get rid
of barriers in rbd_dev_v2_parent_info() while at it - I don't see what
they'd pair with now and I suspect we are in a pretty miserable
situation as far as proper locking goes regardless.
Cc: stable@vger.kernel.org # 3.11+
Signed-off-by: Ilya Dryomov <idryomov@redhat.com>
Reviewed-by: Josh Durgin <jdurgin@redhat.com>
Reviewed-by: Alex Elder <elder@linaro.org>
The libata tag allocation is using a round-robin policy. Next patch will
make libata use block generic tag allocation, so let's add a policy to
tag allocation.
Currently two policies: FIFO (default) and round-robin.
Cc: Jens Axboe <axboe@fb.com>
Cc: Tejun Heo <tj@kernel.org>
Cc: Christoph Hellwig <hch@infradead.org>
Signed-off-by: Shaohua Li <shli@fb.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Converting from to blk-queue got rid of the driver's RCU
locking-on-queue, so removing unnecessary RCU locking-on-queue
artefacts.
Reviewed-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Kelly Nicole Kaoudis <kaoudis@colorado.edu>
Signed-off-by: Jens Axboe <axboe@fb.com>
blkdev_issue_discard() will zero a given block range. This is done by
way of explicit writing, thus provisioning or allocating the blocks on
disk.
There are use cases where the desired behavior is to zero the blocks but
unprovision them if possible. The blocks must deterministically contain
zeroes when they are subsequently read back.
This patch adds a flag to blkdev_issue_zeroout() that provides this
variant. If the discard flag is set and a block device guarantees
discard_zeroes_data we will use REQ_DISCARD to clear the block range. If
the device does not support discard_zeroes_data or if the discard
request fails we will fall back to first REQ_WRITE_SAME and then a
regular REQ_WRITE.
Also update the callers of blkdev_issue_zero() to reflect the new flag
and make sb_issue_zeroout() prefer the discard approach.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@fb.com>
Most of our code has
struct foo {
}
Fix two instances where blk is inconsistent.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Some devices might not implement config space access
(e.g. remoteproc used not to - before 3.9).
virtio/blk needs config space access so make it
fail gracefully if not there.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
null_blk is partitionable, but it doesn't store any of the info. When
it is loaded, you would normally see:
[1226739.343608] nullb0: unknown partition table
[1226739.343746] nullb1: unknown partition table
which can confuse some people. Add the appropriate gendisk flag
to suppress this info.
Signed-off-by: Jens Axboe <axboe@fb.com>
This was inadvertently dropped from an earlier commit, otherwise
the check against cq_vector == -1 to prevent double free doesn't
make any sense.
Fixes: 2b25d98179
Signed-off-by: Jens Axboe <axboe@fb.com>
Because of the direct_access() API which returns a PFN. partitions
better start on 4K boundary, else offset ZERO of a partition will
not be aligned and blk_direct_access() will fail the call.
By setting blk_queue_physical_block_size(PAGE_SIZE) we can communicate
this to fdisk and friends.
The call to blk_queue_physical_block_size() is harmless and will
not affect the Kernel behavior in any way. It is only for
communication to user-mode.
before this patch running fdisk on a default size brd of 4M
the first sector offered is 34 (BAD), but after this patch it
will be 40, ie 8 sectors aligned. Also when entering some random
partition sizes the next partition-start sector is offered 8 sectors
aligned after this patch. (Please note that with fdisk the user
can still enter bad values, only the offered default values will
be correct)
Note that with bdev-size > 4M fdisk will try to align on a 1M
boundary (above first-sector will be 2048), in any case.
CC: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Boaz Harrosh <boaz@plexistor.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
This patch fixes up brd's partitions scheme, now enjoying all worlds.
The MAIN fix here is that currently, if one fdisks some partitions,
a BAD bug will make all partitions point to the same start-end sector
ie: 0 - brd_size And an mkfs of any partition would trash the partition
table and the other partition.
Another fix is that "mount -U uuid" will not work if show_part was not
specified, because of the GENHD_FL_SUPPRESS_PARTITION_INFO flag.
We now always load without it and remove the show_part parameter.
[We remove Dmitry's new module-param part_show it is now always
show]
So NOW the logic goes like this:
* max_part - Just says how many minors to reserve between ramX
devices. In any way, there can be as many partition as requested.
If minors between devices ends, then dynamic 259-major ids will
be allocated on the fly.
The default is now max_part=1, which means all partitions devt(s)
will be from the dynamic (259) major-range.
(If persistent partition minors is needed use max_part=X)
For example with /dev/sdX max_part is hard coded 16.
* Creation of new devices on the fly still/always work:
mknod /path/devnod b 1 X
fdisk -l /path/devnod
Will create a new device if [X / max_part] was not already
created before. (Just as before)
partitions on the dynamically created device will work as well
Same logic applies with minors as with the pre-created ones.
TODO: dynamic grow of device size. So each device can have it's
own size.
CC: Dmitry Monakhov <dmonakhov@openvz.org>
Tested-by: Ross Zwisler <ross.zwisler@linux.intel.com>
Signed-off-by: Boaz Harrosh <boaz@plexistor.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Linus Torvalds
Joonsoo Kim
Keith Busch
Jens Axboe
Christoph Hellwig
Ilya Dryomov
Rickard Strandqvist
Matthew Wilcox
Rasmus Villemoes
Ganesh Mahendran
Sergey Senozhatsky
Minchan Kim
David Vrabel
Roger Pau Monne
Takashi Iwai
Jennifer Herbert
Shaohua Li
kaoudis
Martin K. Petersen
Michael S. Tsirkin
Boaz Harrosh