Fix:
drivers/i2c/busses/i2c-ismt.c: In function ‘ismt_hw_init’:
drivers/i2c/busses/i2c-ismt.c:770:2: error: case label does not reduce to an integer constant
case ISMT_SPGT_SPD_400K:
^~~~
drivers/i2c/busses/i2c-ismt.c:773:2: error: case label does not reduce to an integer constant
case ISMT_SPGT_SPD_1M:
^~~~
See https://lore.kernel.org/r/YkwQ6%2BtIH8GQpuct@zn.tnic for the gory
details as to why it triggers with older gccs only.
Signed-off-by: Borislav Petkov <bp@suse.de>
Reviewed-by: Seth Heasley <seth.heasley@intel.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Sparse has warned us about wrong address space for user pointers:
i2c-dev.c:561:50: warning: incorrect type in initializer (different address spaces)
i2c-dev.c:561:50: expected unsigned char [usertype] *buf
i2c-dev.c:561:50: got void [noderef] __user *
Force cast the pointer to (__u8 *) that is used by I²C core code.
Note, this is an additional fix to the previously addressed similar issue
in the I2C_RDWR case in the same function.
Fixes: 3265a7e6b4 ("i2c: dev: Add __user annotation")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
If dev_set_name() fails, the dev_name() is null, check the return
value of dev_set_name() to avoid the null-ptr-deref.
Fixes: 1413ef638a ("i2c: dev: Fix the race between the release of i2c_dev and cdev")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
The GPI DMA engine driver can be compiled as a module, in which case the
likely probe deferral "error" shows up in the kernel log. Switch to
using dev_err_probe() to silence this warning and to ensure that
"devices_deferred" in debugfs carries this information.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
The i.MX8MP Mask Set Errata for Mask 1P33A, Rev. 2.0 has description of
errata ERR007805 as below. This errata is found on all MX8M{M,N,P,Q},
MX7{S,D}, MX6{UL{,L,Z},S{,LL,X},S,D,DL,Q,DP,QP} . MX7ULP, MX8Q, MX8X
are not affected. MX53 and older status is unknown, as the errata
first appears in MX6 errata sheets from 2016 and the latest errata
sheet for MX53 is from 2015. Older SoC errata sheets predate the
MX53 errata sheet. MX8ULP and MX9 status is unknown as the errata
sheet is not available yet.
"
ERR007805 I2C: When the I2C clock speed is configured for 400 kHz,
the SCL low period violates the I2C spec of 1.3 uS min
Description: When the I2C module is programmed to operate at the
maximum clock speed of 400 kHz (as defined by the I2C spec), the SCL
clock low period violates the I2C spec of 1.3 uS min. The user must
reduce the clock speed to obtain the SCL low time to meet the 1.3us
I2C minimum required. This behavior means the SoC is not compliant
to the I2C spec at 400kHz.
Workaround: To meet the clock low period requirement in fast speed
mode, SCL must be configured to 384KHz or less.
"
Implement the workaround by matching on the affected SoC specific
compatible strings and by limiting the maximum bus frequency in case
the SoC is affected.
Signed-off-by: Marek Vasut <marex@denx.de>
To: linux-i2c@vger.kernel.org
Acked-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Wait for completion of write transfers before returning from the driver.
At first sight it may seem advantageous to leave write transfers queued
for the controller to carry out on its own time, but there's a couple of
issues with it:
* Driver doesn't check for FIFO space.
* The queued writes can complete while the driver is in its I2C read
transfer path which means it will get confused by the raising of
XEN (the 'transaction ended' signal). This can cause a spurious
ENODATA error due to premature reading of the MRXFIFO register.
Adding the wait fixes some unreliability issues with the driver. There's
some efficiency cost to it (especially with pasemi_smb_waitready doing
its polling), but that will be alleviated once the driver receives
interrupt support.
Fixes: beb58aa39e ("i2c: PA Semi SMBus driver")
Signed-off-by: Martin Povišer <povik+lin@cutebit.org>
Reviewed-by: Sven Peter <sven@svenpeter.dev>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Pull i2c updates from Wolfram Sang:
- tracepoints when Linux acts as an I2C client
- added support for AMD PSP
- whole subsystem now uses generic_handle_irq_safe()
- piix4 driver gained MMIO access enabling so far missed controllers
with AMD chipsets
- a bulk of device driver updates, refactorization, and fixes.
* 'i2c/for-mergewindow' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (61 commits)
i2c: mux: demux-pinctrl: do not deactivate a master that is not active
i2c: meson: Fix wrong speed use from probe
i2c: add tracepoints for I2C slave events
i2c: designware: Remove code duplication
i2c: cros-ec-tunnel: Fix syntax errors in comments
MAINTAINERS: adjust XLP9XX I2C DRIVER after removing the devicetree binding
i2c: designware: Mark dw_i2c_plat_{suspend,resume}() as __maybe_unused
i2c: mediatek: Add i2c compatible for Mediatek MT8168
dt-bindings: i2c: update bindings for MT8168 SoC
i2c: mt65xx: Simplify with clk-bulk
i2c: i801: Drop two outdated comments
i2c: xiic: Make bus names unique
i2c: i801: Add support for the Process Call command
i2c: i801: Drop useless masking in i801_access
i2c: tegra: Add SMBus block read function
i2c: designware: Use the i2c_mark_adapter_suspended/resumed() helpers
i2c: designware: Lock the adapter while setting the suspended flag
i2c: mediatek: remove redundant null check
i2c: mediatek: modify bus speed calculation formula
i2c: designware: Fix improper usage of readl
...
power-supply core:
- Introduce "Bypass" charging type used by USB PPS standard
- Refactor power_supply_set_input_current_limit_from_supplier()
- Add fwnode support to power_supply_get_battery_info()
Drivers:
- ab8500: continue migrating towards using standard core APIs
- axp288 fuel-gauge: refactor driver to be fully resource managed
- battery-samsung-sdi: new in-kernel provider for (constant) Samsung battery info
- bq24190: disable boost regulator on shutdown
- bq24190: add support for battery-info on ACPI based systems
- bq25890: prepare driver for usage on ACPI based systems
- bq25890: add boost regulator support
- cpcap-battery: add NVMEM based battery detection support
- injoinic ip5xxx: new driver for power bank IC
- upi ug3105: new battery driver
- misc. small improvements and fixes
-----BEGIN PGP SIGNATURE-----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=OiYc
-----END PGP SIGNATURE-----
Merge tag 'for-v5.18' of git://git.kernel.org/pub/scm/linux/kernel/git/sre/linux-power-supply
Pull power supply and reset updates from Sebastian Reichel:
"Power-supply core:
- Introduce "Bypass" charging type used by USB PPS standard
- Refactor power_supply_set_input_current_limit_from_supplier()
- Add fwnode support to power_supply_get_battery_info()
Drivers:
- ab8500: continue migrating towards using standard core APIs
- axp288 fuel-gauge: refactor driver to be fully resource managed
- battery-samsung-sdi: new in-kernel provider for (constant) Samsung
battery info
- bq24190: disable boost regulator on shutdown
- bq24190: add support for battery-info on ACPI based systems
- bq25890: prepare driver for usage on ACPI based systems
- bq25890: add boost regulator support
- cpcap-battery: add NVMEM based battery detection support
- injoinic ip5xxx: new driver for power bank IC
- upi ug3105: new battery driver
- misc small improvements and fixes"
* tag 'for-v5.18' of git://git.kernel.org/pub/scm/linux/kernel/git/sre/linux-power-supply: (94 commits)
power: ab8500_chargalg: Use CLOCK_MONOTONIC
power: supply: Add a driver for Injoinic power bank ICs
dt-bindings: trivial-devices: Add Injoinic power bank ICs
dt-bindings: vendor-prefixes: Add Injoinic
power: supply: ab8500: Remove unused variable
power: supply: da9150-fg: Remove unnecessary print function dev_err()
power: supply: ab8500: fix a handful of spelling mistakes
power: supply: ab8500_fg: Account for line impedance
dt-bindings: power: supply: ab8500_fg: Add line impedance
power: supply: axp20x_usb_power: fix platform_get_irq.cocci warnings
power: supply: axp20x_ac_power: fix platform_get_irq.cocci warning
power: supply: wm8350-power: Add missing free in free_charger_irq
power: supply: wm8350-power: Handle error for wm8350_register_irq
power: supply: Static data for Samsung batteries
power: supply: ab8500_fg: Use VBAT-to-Ri if possible
power: supply: Support VBAT-to-Ri lookup tables
power: supply: ab8500: Standardize BTI resistance
power: supply: ab8500: Standardize alert mode charging
power: supply: ab8500: Standardize maintenance charging
power: supply: bq24190_charger: Delay applying charge_type changes when OTG 5V Vbus boost is on
...
Attempting to rollback the activation of the current master when
the current master has not been activated is bad. priv->cur_chan
and priv->cur_adap are both still zeroed out and the rollback
may result in attempts to revert an of changeset that has not been
applied and do result in calls to both del and put the zeroed out
i2c_adapter. Maybe it crashes, or whatever, but it's bad in any
case.
Fixes: e9d1a0a41d ("i2c: mux: demux-pinctrl: Fix an error handling path in 'i2c_demux_pinctrl_probe()'")
Signed-off-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Having meson_i2c_set_clk_div after i2c_add_adapter
causes issues for client drivers that try to use
the bus before the requested speed is applied.
The bus can be used just after i2c_add_adapter, so
move i2c_add_adapter to the final step as
meson_i2c_set_clk_div needs to be called before
the bus is used.
Fixes: 09af1c2fa4 ("i2c: meson: set clock divider in probe instead of setting it for each transfer")
Signed-off-by: Lucas Tanure <tanure@linux.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Simplify code by moving common part to one function.
Signed-off-by: Jan Dabros <jsd@semihalf.com>
Suggested-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Delete the redundant word 'to'
Signed-off-by: Xiang wangx <wangxiang@cdjrlc.com>
[wsa: fixed prefix in subject]
Signed-off-by: Wolfram Sang <wsa@kernel.org>
When CONFIG_PM is set but CONFIG_PM_SLEEP is not, two compiler warnings
appear:
drivers/i2c/busses/i2c-designware-platdrv.c:444:12: error: unused function 'dw_i2c_plat_suspend' [-Werror,-Wunused-function]
static int dw_i2c_plat_suspend(struct device *dev)
^
drivers/i2c/busses/i2c-designware-platdrv.c:465:12: error: unused function 'dw_i2c_plat_resume' [-Werror,-Wunused-function]
static int dw_i2c_plat_resume(struct device *dev)
^
2 errors generated.
These functions are only used in SET_LATE_SYSTEM_SLEEP_PM_OPS(), which
is defined as empty when CONFIG_PM_SLEEP is not defined. Mark the
functions as __maybe_unused to make it clear that these functions might
be unused in this configuration.
Fixes: c57813b8b2 ("i2c: designware: Lock the adapter while setting the suspended flag")
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Add i2c compatible for MT8168. Compare to MT2712 i2c controller,
MT8168 need to synchronize signal with dma.
Signed-off-by: Kewei Xu <kewei.xu@mediatek.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Qii Wang <qii.wang@mediatek.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Since depending on the SoC or specific bus functionality some clocks
may be optional, we cannot get the benefit of using devm_clk_bulk_get()
but, by migrating to clk-bulk, we are able to remove the custom functions
mtk_i2c_clock_enable() and mtk_i2c_clock_disable(), increasing common
APIs usage, hence (lightly) decreasing kernel footprint.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Qii Wang <qii.wang@mediatek.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
* Timeouts are reported even in interrupt mode since commit
b3b8df9772 ("i2c: i801: Use wait_event_timeout to wait for
interrupts") so drop the comment which claims this only happens in
polled mode.
* xact does not include the PEC bit, as the driver does not support
software PEC.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Reviewed-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
This driver is for an FPGA logic core, so there can be arbitrarily many
instances of the bus on a given system. Previously all of the I2C bus
names were "xiic-i2c" which caused issues with lm_sensors when trying to
map human-readable names to sensor inputs because it could not properly
distinguish the busses, for example. Append the platform device name to
the I2C bus name so it is unique between different instances.
Fixes: e1d5b6598c ("i2c: Add support for Xilinx XPS IIC Bus Interface")
Signed-off-by: Robert Hancock <robert.hancock@calian.com>
Tested-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
The Process Call command is implemented by the hardware since the very
first Intel 82801 chipset, and trivial to support. Oscar Romero
Matamala from the Georgia Institute of Technology told me it is needed
for an experiment his team is working on at the moment, so let's just
add support for it.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Reviewed-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
I went all the way back to kernel 2.6.12 and that masking was never
needed. I suppose it was there in anticipation of software PEC
support, but that was never added to the driver (and never will be,
as this is made obsolete by hardware PEC).
I'm also removing initialization to 0, which is not needed either,
and would prevent the compiler from reporting an actual usage of
uninitialized variables.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Reviewed-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Use the i2c_mark_adapter_suspended/resumed() i2c-core helpers and rely
on the i2c-core's suspended checking instead of using DIY code.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Lock the adapter while setting the suspended flag, to ensure that other
locked code always sees the change immediately, rather then possibly using
a stale value.
This involves splitting the suspend/resume callbacks into separate runtime
and normal suspend/resume calls. This is necessary because i2c_dw_xfer()
will get called by the i2c-core with the adapter locked and it in turn
calls the runtime-resume callback through pm_runtime_get_sync().
So the runtime versions of the suspend/resume callbacks cannot take
the adapter-lock. Note this patch simply makes the runtime suspend/resume
callbacks not deal with the suspended flag at all. During runtime the
pm_runtime_get_sync() from i2c_dw_xfer() will always ensure that the
adapter is resumed when necessary.
The suspended flag check is only necessary to check proper suspend/resume
ordering during normal suspend/resume which makes the pm_runtime_get_sync()
call a no-op.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Because clk_disable_unprepare already checked NULL clock parameter,
so the additional checks are unnecessary, just remove it
Signed-off-by: Xu Wang <vulab@iscas.ac.cn>
Reviewed-by: Qii Wang <qii.wang@mediatek.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
When clock-div is 0 or greater than 1, the bus speed
calculated by the old speed calculation formula will be
larger than the target speed. So we update the formula.
Signed-off-by: Kewei Xu <kewei.xu@mediatek.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Qii Wang <qii.wang@mediatek.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Kernel test robot reported incorrect type in argument 1 of readl(), but
more importantly it brought attention that MMIO accessor shouldn't be
used in this case, since req->hdr.status is part of a command-response
buffer in system memory.
Since its value may be altered by PSP outside of the scope of current
thread (somehow similar to IRQ handler case), we need to use
READ_ONCE() to ensure compiler won't optimize this call.
Fix also 'status' variable type to reflect that corresponding field in
command-response buffer is platform-independent u32.
Fixes: 78d5e9e299 ("i2c: designware: Add AMD PSP I2C bus support")
Signed-off-by: Jan Dabros <jsd@semihalf.com>
Reported-by: kernel test robot <lkp@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
QUP Serial engines supports data transfers thru FIFO mode, SE DMA mode
and lastly GPI DMA mode. Former two are already supported and this adds
supports for the last mode.
In GPI DMA mode, the firmware is issued commands by driver to perform
DMA and setup the serial port.
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Read reset phandle as optional instead of exclusive so that all the DT's
passing the reset phandle can be used to assert/deassert the reset line.
With this change we don't have to differentiate the RZ/G2L SoC.
With the above changes we no longer need the "renesas,riic-r9a07g044"
compatible string, so drop it from riic_i2c_dt_ids[]. No changes are
required to the r9a07g044.dtsi as we already have "renesas,riic-rz" as a
fallback compatible string.
While at it, check the return code of reset_control_deassert() as it might
fail and also add a devres action to assert the reset line.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Instead of manually disabling interrupts before invoking use
generic_handle_irq_safe() which can be invoked with enabled and disabled
interrupts.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
The i2c-i801 driver invokes i2c_handle_smbus_host_notify() from his
interrupt service routine. On PREEMPT_RT i2c-i801's handler is forced
threaded with enabled interrupts which leads to a warning by
handle_irq_event_percpu() assuming that irq_default_primary_handler()
enabled interrupts.
i2c-i801's interrupt handler can't be made non-threaded because the
interrupt line is shared with other devices.
Use generic_handle_irq_safe() which can invoked with disabled and enabled
interrupts.
Reported-by: Michael Below <below@judiz.de>
Link: https://bugs.debian.org/1002537
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Reviewed-by: Oleksandr Natalenko <oleksandr@natalenko.name>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
An I²C adapter might be instantiated without parent. In such case
there is no property can be retrieved. Skip SMBus alert setup when
this happens.
Fixes: a263a84088 ("i2c: smbus: Use device_*() functions instead of of_*()")
Reported-by: syzbot+0591ccf54ee05344e4eb@syzkaller.appspotmail.com
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
DSL and CM (Cable Modem) support 8 B max transfer size and have a custom
DT binding for that reason. This driver was checking for a wrong
"compatible" however which resulted in an incorrect setup.
Fixes: e2e5a2c618 ("i2c: brcmstb: Adding support for CM and DSL SoCs")
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Add QCOM SM8450 specific compatible for CCI controller, which is
equal to CCI controllers found on QCOM SDM845 and QCOM SM8250 SoCs.
Signed-off-by: Vladimir Zapolskiy <vladimir.zapolskiy@linaro.org>
Reviewed-by: Robert Foss <robert.foss@linaro.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Drop I2C device-probing classes from platform variant of the PASemi
controller as it is only used on platforms where I2C devices should
be instantiated in devicetree. (The I2C_CLASS_DEPRECATED flag is not
raised as up to this point no devices relied on the old behavior.)
Fixes: d88ae2932d ("i2c: pasemi: Add Apple platform driver")
Signed-off-by: Martin Povišer <povik+lin@cutebit.org>
Reviewed-by: Sven Peter <sven@svenpeter.dev>
Acked-by: Hector Martin <marcan@marcan.st>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Driver builds fine with COMPILE_TEST. Enable it for wider test coverage
and easier maintenance.
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Acked-by: Oleksij Rempel <o.rempel@pengutronix.de>
Driver builds fine with COMPILE_TEST. Enable it for wider test coverage
and easier maintenance.
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Eliminate the following coccicheck warnings:
./drivers/i2c/busses/i2c-designware-amdpsp.c:172:2-3: Unneeded semicolon
./drivers/i2c/busses/i2c-designware-amdpsp.c:245:2-3: Unneeded semicolon
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Signed-off-by: Yang Li <yang.lee@linux.alibaba.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Reviewed-by: Jan Dabros <jsd@semihalf.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Instead of open coded variant switch to use i2c_new_ccgx_ucsi().
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
It's fine to call dev_err_probe() in ->probe() when error code is known.
Convert the driver to use dev_err_probe().
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Use temporary variable for struct device to make code neater.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Instead of open coded variant switch to use i2c_new_ccgx_ucsi().
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Introduce a common module to provide an API to instantiate UCSI device
for Cypress CCGx Type-C controller. Individual bus drivers need to select
this one on demand.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Add SMBus PCI ID on Intel Raptor Lake PCH-S.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
i2c_setup_smbus_alert() is only needed within the I2C core, so no need
to expose it to other modules.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
There is a minor chance for a race, if a pointer to an i2c-bus subnode
is stored and then reused after releasing its reference, and it would
be sufficient to get one more reference under a loop over children
subnodes.
Fixes: e517526195 ("i2c: Add Qualcomm CCI I2C driver")
Signed-off-by: Vladimir Zapolskiy <vladimir.zapolskiy@linaro.org>
Reviewed-by: Robert Foss <robert.foss@linaro.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
If i2c_add_adapter() fails to add an I2C adapter found on QCOM CCI
controller, on error path i2c_del_adapter() is still called.
Fortunately there is a sanity check in the I2C core, so the only
visible implication is a printed debug level message:
i2c-core: attempting to delete unregistered adapter [Qualcomm-CCI]
Nevertheless it would be reasonable to correct the probe error path.
Fixes: e517526195 ("i2c: Add Qualcomm CCI I2C driver")
Signed-off-by: Vladimir Zapolskiy <vladimir.zapolskiy@linaro.org>
Reviewed-by: Robert Foss <robert.foss@linaro.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
BCM4908 SoCs use the same I2C hardware block as STB and BCM63xx devices.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Add support for the I2C Bus Interface on R-Car Gen4 SoCs (e.g. R-Car
S4-8) by matching on a family-specific compatible value.
While I2C on R-Car Gen4 does support some extra features (Slave Clock
Stretch Select), for now it is treated the same as I2C on R-Car Gen3.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
[wsa: removed incorrect "FM+" from commit message]
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Borislav Petkov
Andy Shevchenko
Bjorn Andersson
Marek Vasut
Martin Povišer
Linus Torvalds
Peter Rosin
Lucas Tanure
Jae Hyun Yoo
Jan Dabros
Xiang wangx
Nathan Chancellor
Kewei Xu
AngeloGioacchino Del Regno
Jean Delvare
Robert Hancock
Akhil R
Hans de Goede
Xu Wang
Vinod Koul
Lad Prabhakar
Sebastian Andrzej Siewior
Wolfram Sang
Rafał Miłecki
Vladimir Zapolskiy
Yang Li
Jarkko Nikula
Wolfram Sang
Geert Uytterhoeven