The TSEC/eTSEC can detect the interface to the PHY automatically,
but it isn't able to detect whether the RGMII connection needs internal
delay. So we need to detect that change in the device tree, propagate
it to the platform data, and then check it if we're in RGMII. This fixes
a bug on the 8641D HPCN board where the Vitesse PHY doesn't use the delay
for RGMII.
Signed-off-by: Andy Fleming <afleming@freescale.com>
The Vitesse PHY on the 8641D needs to be set up with internal delay to
work in RGMII mode. So we add skew when it is set to RGMII_ID mode.
Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Haruki Dai <Dai.Haruki@freescale.com>
Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>
The TSEC/eTSEC automatically detect their PHY interface type, unless
the type is RGMII-ID (RGMII with internal delay). In that situation,
it just detects RGMII. In order to fix this, we need to pass in rgmii-id
if that is the connection type.
Signed-off-by: Andy Fleming <afleming@freescale.com>
The Vitesse 824x PHY doesn't allow an interrupt to be cleared if
the mask bit for that interrupt isn't set. This means that the PHY
Lib's order of handling interrupts (disable, then clear) breaks on this
PHY. However, clearing then disabling the interrupt opens up the code
for a silly race condition. So rather than change the PHY Lib, we change
the Vitesse driver so it always clears interrupts before disabling them.
Further, the ack function only clears the interrupt if interrupts are
enabled.
Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: York Sun <yorksun@freescale.com>
Acked-by: Haiying Wang <Haiying.Wang@freescale.com>
Coverity (1792) spotted a possibly uninitialized return value in case of
kmalloc() failure:
1116 static int hisax_cs_setup(int cardnr, struct IsdnCard *card,
1117 struct IsdnCardState *cs)
1119 int ret;
1120
1121 if (!(cs->rcvbuf = kmalloc(MAX_DFRAME_LEN_L1, GFP_ATOMIC))) {
1122 printk(KERN_WARNING "HiSax: No memory for isac rcvbuf\n");
1123 ll_unload(cs);
1124 goto outf_cs;
...
1165 outf_cs:
1166 kfree(cs);
1167 card->cs = NULL;
1168 return ret;
The straightforward solution would be to just add the missing
initialization but hardcoding the return value in the out_cs branch
(only taken on failure) seems to work just as well and it allows killing
a couple of other lines too.
Signed-off-by: Florin Malita <fmalita@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Found and debugged by Jay Fenlason <fenlason@redhat.com>.
The bug was especially noticeable with direct I/O over fw-sbp2.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: Kristian Høgsberg <krh@redhat.com>
This check is bogus:
- Maximum asynchronous payload size for S800...S3200 is 4096.
- The p->payload_length is totally uninteresting. Only the
request->length of the subsequently allocated and initialized
struct fw_request is of significance.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: Kristian Høgsberg <krh@redhat.com>
Current code sets size0 to 0 at the start of work request posting
functions and then handles size0 == 0 specially within the loop over
work requests. Change this so size0 is set along with f0 the first
time through the loop (when nreq == 0). This makes the code easier to
understand by making it clearer that f0 and size0 are always
initialized if nreq != 0 without having to know that size0 == 0
implies nreq == 0.
Also annotate size0 with uninitialized_var() so that this doesn't
introduce a new compiler warning.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Factor code to set UD entries out of the work request posting
functions into inline functions set_tavor_ud_seg() and
set_arbel_ud_seg(). This doesn't change the generated code in any
significant way, and makes the source easier on the eyes.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/hskinnemoen/avr32-2.6:
[AVR32] Initialize phy_mask for both macb devices
[AVR32] Fix atomic_add_unless() and atomic_sub_unless()
[AVR32] Correct misspelled CONFIG_BLK_DEV_INITRD variable.
[AVR32] Fix build error in parse_tag_rdimg()
[AVR32] Don't wire up macb0 unless SW6 is in default position
[AVR32] Wire up SSC platform device 0 as TX on ATSTK1000 board
[AVR32] Add Atmel SSC driver platform device to AT32AP architecture
[AVR32] Remove optimization of unaligned word loads
[AVR32] Make STK1000 mux settings configurable
[AVR32] CPU frequency scaling for AT32AP
[AVR32] Split SM device into PM, RTC, WDT and EIC
[AVR32] faster avr32 unaligned access
Factor code to set remote address and atomic segment entries out of the
work request posting functions into inline functions set_raddr_seg()
and set_atomic_seg(). This doesn't change the generated code in any
significant way, and makes the source easier on the eyes.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/hpa/linux-2.6-x86setup:
[PATCH] x86: do not recompile boot for each build
[x86 setup] Save/restore DS around invocations of INT 10h
[x86 setup] VGA: Clear the Protect bit before setting the vertical height
[x86 setup] Fix assembly constraints
[x86 setup] build/tools.c: fix comment
[x86 setup] MAINTAINERS: document x86 setup code git tree
The TRACE_IRQS_ON function in iret_exc: calls a C function without
ensuring that the segments are set properly. Move the trace function and
the enabling of interrupt into the C stub.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The code for LDT segment selectors was not robust in the face of a bogus
selector set in %cs via ptrace before the single-step was done.
Signed-off-by: Roland McGrath <roland@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Factor code to set remote address, atomic and datagram segments out of
mlx4_ib_post_send() into small helper functions. This doesn't change
the generated code in any significant way, and makes the source easier
on the eyes.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The STK1000 uses pullups on the MDIO lines to the PHY, but they are
too weak. This causes the PHY layer to detect PHYs on all possible MII
addresses. Mask out all but the correct address to prevent this from
happening.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
These functions depend on "result" being initalized to 0, but "result"
is not included as an input constraint to the inline assembly block
following its initialization, only as an output constraint. Thus gcc
thinks it doesn't need to initialize it, so result ends up undefined
if the "unless" condition is true.
This fixes an oops in sunrpc where the faulty atomics caused
rpciod_up() to not start the workqueue as it should.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
This code is inside an #ifdef with a misspelled config symbol, so it
hasn't been used for a long time. Fix it before fixing the config
symbol to keep bisection working.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Factor code to set data segment entries out of mlx4_ib_post_send()
into set_data_seg(). This cleans up the code and lets the compiler do
a better job -- on x86_64:
add/remove: 0/0 grow/shrink: 0/1 up/down: 0/-16 (-16)
function old new delta
mlx4_ib_post_send 1598 1582 -16
Signed-off-by: Roland Dreier <rolandd@cisco.com>
This patch adds register definitions, clocks and IRQs to the platform devices.
Signed-off-by: Hans-Christian Egtvedt <hcegtvedt@atmel.com>
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
If we let unaligned word loads bypass the generic unaligned handling,
gcc may combine it with a swap.b instruction and turn it into a ldwsp
instruction, which does not work with unaligned addresses.
Revert the optimization to prevent the RNDIS driver from crashing.
Hopefully we'll figure something out later (it may be better to do the
optimization in gcc.)
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
This adds some STK1002-specific config options covering the jumper settings,
so the kernel can automatically be configured to include the relevant devices.
One of them replaces the previous internal SW2_DEFAULT setting; SPI config
is affected by two of the jumpers; and a fourth one switches between LCD and
the second Ethernet connector. (There's more that to be done.)
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
This patch enables CPU frequency scaling for AT32AP devices. This will
enable the CPU to scale between the speed of the high speed bus and
the master clock and thus save some power.
The patch also adds a parent to cpu_clk and a cpu_clk_set_rate to
enable changing the CPU clock divider in a sane way.
The driver does not check if the given rate is 0, thus resulting in a
div by 0. I think this check should be go into the clk_set_rate
framework, and not here.
Tested on AT32AP7000/ATSTK1000.
Hardware documentation can be found in the AT32AP7000 datasheet.
Signed-off-by: Hans-Christian Egtvedt <hcegtvedt@atmel.com>
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Split the SM platform device into separate platform devices for PM,
RTC, WDT and EIC. This is more correct according to the documentation
and allows us to simplify the code a little.
Also turn the EIC driver into a real platform driver.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Acked-by: Hans-Christian Egtvedt <hcegtvedt@atmel.com>
Use a more conventional implementation for unaligned access, and include
an AT32AP-specific optimization: the CPU will handle unaligned words.
The result is always faster and smaller for 8, 16, and 32 bit values.
For 64 bit quantities, it's presumably larger.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Keep the arch/i386/boot directory from being rebuilt every time.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
There exists at least one card, Trident TVGA8900CL (BIOS dated 1992/9/8)
which clobbers DS when "scrolling in an SVGA text mode of more than
800x600 pixels." Although we are extremely unlikely to run into that
situation, it is cheap insurance to save and restore DS, and it only adds
a grand total of 50 bytes to the total output.
Pointed out by Etienne Lorrain.
Cc: Etienne Lorrain <etienne_lorrain@yahoo.fr>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
If the user has asked for the vertical height registers to be recomputed
by setting bit 15 in the video mode number, we do so without clearing the
Protect bit in the Vertical Retrace Register before setting the Overflow
register. As a result, if the VGA BIOS had set the Protect bit, the
write to the Overflow register will be dropped, and bits [9:8] of the
vertical height will be left unchanged.
This is a bug imported from the assembly version of this code. It was
pointed out by Etienne Lorrain.
Cc: Etienne Lorrain <etienne_lorrain@yahoo.fr>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Fix incorrect assembly constraints. In particular, fix memory
constraints used inside push..pop, which can cause invalid operation
since gcc may generate %esp-relative references.
Additionally:
outl() should have "dN" not "dn".
query_mca() shouldn't listen 16/32-bit registers in an 8-bit only
context.
has_eflag(): the "mask" is only used well after both the stack pointer
and the output registers have been touched; this requires the output
registers to be earlyclobbers (=&) and the input to exclude memory (so
"ri", not "g").
Thanks to Etienne Lorrain and Chuck Ebbert for prompting this review.
Cc: Etienne Lorrain <etienne_lorrain@yahoo.fr>
Cc: Chuck Ebbert <cebbert@redhat.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Correct a comment in arch/i386/boot/build/tools.c; we now build the
kernel from only two components instead of three, since the boot
sector has been integrated in the setup code.
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Factor code to set data segment entries out of the work request
posting functions into inline functions mthca_set_data_seg() and
mthca_set_data_seg_inval(). This makes the code more readable and
also allows the compiler to do a better job -- on x86_64:
add/remove: 0/0 grow/shrink: 0/6 up/down: 0/-69 (-69)
function old new delta
mthca_arbel_post_srq_recv 373 369 -4
mthca_arbel_post_receive 570 562 -8
mthca_tavor_post_srq_recv 520 508 -12
mthca_tavor_post_send 1344 1330 -14
mthca_arbel_post_send 1481 1467 -14
mthca_tavor_post_receive 792 775 -17
Signed-off-by: Roland Dreier <rolandd@cisco.com>
* 'master' of ssh://master.kernel.org/pub/scm/linux/kernel/git/mchehab/v4l-dvb: (126 commits)
V4L/DVB (5847): Clean up schedule_timeout calls in cpia2 and ivtv code
V4L/DVB (5846): Clean up setting state and scheduling timeouts
V4L/DVB (5844): ivtv: add high volume debugging flag
V4L/DVB (5843): ivtv: fix missing signal_pending check.
V4L/DVB (5842): ivtv: Add locking to ensure stream setup is atomic.
V4L/DVB (5841): tveeprom: add support for Philips FQ1216LME MK3 tuner.
V4L/DVB (5840): fix dst and cx24123: tune() callback changed signess for delay
V4L/DVB (5838): dvb-core: Fix signedness warnings (gcc 4.1.1, kernel 2.6.22)
V4L/DVB (5837): stv0299: Fix signedness warning (gcc 4.1.1, kernel 2.6.22)
V4L/DVB (5836): dvb-ttpci: re-initialize aspect ratio and pan scan after arm crash
V4L/DVB (5835): saa7146/dvb-ttpci: Fix signedness warnings (gcc 4.1.1, kernel 2.6.22)
V4L/DVB (5834): dvb-core: fix signedness warnings and const stripping
V4L/DVB (5832): ir-common: optimize bit extract function
V4L/DVB (5831): stradis: use ARRAY_SIZE
V4L/DVB (5829): Firmware extract and loading for opera dvb-usb update
V4L/DVB (5828): Kconfig: Added GemTek USB radio and removed experimental dependency.
V4L/DVB (5826): Usbvision: video mux cleanup
V4L/DVB (5825): Alter the tuner type for the WinTV USB UK PAL model.
V4L/DVB (5824): Usbvision: Hauppauge WinTV USB SECAM_L fix
V4L/DVB (5821): Saa7134: add remote control support for LifeView FlyDVB-S LR300
...
* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4:
ext4: extent macros cleanup
Fix compilation with EXT_DEBUG, also fix leXX_to_cpu conversions.
ext4: remove extra IS_RDONLY() check
ext4: Use is_power_of_2()
Use zero_user_page() in ext4 where possible
ext4: Remove 65000 subdirectory limit
ext4: Expand extra_inodes space per the s_{want,min}_extra_isize fields
ext4: Add nanosecond timestamps
jbd2: Move jbd2-debug file to debugfs
jbd2: Fix CONFIG_JBD_DEBUG ifdef to be CONFIG_JBD2_DEBUG
ext4: Set the journal JBD2_FEATURE_INCOMPAT_64BIT on large devices
ext4: Make extents code sanely handle on-disk corruption
ext4: copy i_flags to inode flags on write
ext4: Enable extents by default
Change on-disk format to support 2^15 uninitialized extents
write support for preallocated blocks
fallocate support in ext4
sys_fallocate() implementation on i386, x86_64 and powerpc
Signed-off-by: Robert P. J. Day <rpjday@mindspring.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Replace assignments to "current->state" with the preferred calls to
schedule_timeout_interruptible().
Signed-off-by: Robert P. J. Day <rpjday@mindspring.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Add support for high volume debug messages, allowing them to be turned
on selectively.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Yoichi Yuasa
Jeff Garzik
YOSHIFUJI Hideaki / 吉藤英明
Andy Fleming
Florin Malita
Stefan Richter
Roland Dreier
Linus Torvalds
Peter Zijlstra
Roland McGrath
Haavard Skinnemoen
Robert P. J. Day
Kristoffer Nyborg Gregertsen
Hans-Christian Egtvedt
David Brownell
David Brownell
Sam Ravnborg
H. Peter Anvin
Hans Verkuil