At times gcc will place bits of __exit functions into .rodata. If
compiled into the kernle itself we used to discard .exit.text - but
not the bits left in .rodata. While harmless this did at times result
in a large number of warnings. So until gcc fixes this, discard
.exit.text at runtime.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
In case a particular system doesn't support highmem the runtime checks
will ensure nothing bad is going to happen.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
ATI chipsets tend to generate double timer interrupts for the local APIC
timer when both the 8254 and the IO-APIC timer pins are enabled. This is
because they route it to both and the result is anded together and the CPU
ends up processing it twice.
This patch changes check_timer to disable the 8254 routing for interrupt 0.
I think it would be safe on all chipsets actually (i tested it on a couple
and it worked everywhere) and Windows seems to do it in a similar way, but
to be conservative this patch only enables this mode on ATI (and adds
options to enable/disable too)
Ported over from a similar x86-64 change.
I reused the ACPI earlyquirk infrastructure for the ATI bridge check, but
tweaked it a bit to work even without ACPI.
Inspired by a patch from Chuck Ebbert, but redone.
Cc: Chuck Ebbert <76306.1226@compuserve.com>
Cc: "Brown, Len" <len.brown@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
A pte may be zapped by the swapper, exiting process, unmapping or page
migration while the accessed or dirty bit handers are about to run. In that
case the accessed bit or dirty is set on an zeroed pte which leads the VM to
conclude that this is a swap pte. This may lead to
- Messages from the vm like
swap_free: Bad swap file entry 4000000000000000
- Processes being aborted
swap_dup: Bad swap file entry 4000000000000000
VM: killing process ....
Page migration is particular suitable for the creation of this race since
it needs to remove and restore page table entries.
The fix here is to check for the present bit and simply not update
the pte if the page is not present anymore. If the page is not present
then the fault handler should run next which will take care of the problem
by bringing the page back and then mark the page dirty or move it onto the
active list.
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Patch from Alessandro Zummo
The patch that would have made the NSLU2
kernel non compatible with other ixp4xx machs
never entered the kernel. So it is actually
safe to remove the prompt dependencies.
Signed-off-by: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Alessandro Zummo
Disable GPIO clocks to allow
the power led to work properly.
Signed-off-by: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
While testing kexec and kdump we hit problems where the new kernel would
freeze or instantly reboot. The easiest way to trigger it was to kexec a
kernel compiled for CONFIG_M586 on an athlon cpu. Compiling for CONFIG_MK7
instead would work fine.
The patch fixes a few problems with the kexec inline asm.
Signed-off-by: Chris Mason <mason@suse.com>
Acked-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The x86_model calculation also applies for family 6. early_cpu_detect
does the right thing, but generic_identify misses.
Signed-off-by: Shaohua Li<shaohua.li@intel.com>
Cc: Dave Jones <davej@codemonkey.org.uk>
Cc: "Seth, Rohit" <rohit.seth@intel.com>
Acked-by: Andi Kleen <ak@muc.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
strnlen_user is supposed to return then length count + 1 if no terminating \0
is found, and it should return 0 on exception. Found by David Howells
<dhowells@redhat.com>.
Signed-off-by: Gerald Schaefer <geraldsc@de.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Acked-By: David Howells <dhowells@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix i386 nmi_watchdog that does not meet watchdog timeout condition. It
does not hit die_nmi when it should be triggered, because the current
nmi_watchdog_tick in arch/i386/kernel/nmi.c never count up alert_counter
like this:
void nmi_watchdog_tick (struct pt_regs * regs) {
if (last_irq_sums[cpu] == sum) {
alert_counter[cpu]++; <- count up alert_counter, but
if (alert_counter[cpu] == 5*nmi_hz)
die_nmi(regs, "NMI Watchdog detected LOCKUP");
alert_counter[cpu] = 0; <- reset alert_counter
This patch changes it back to the previous and working version.
This was found and originally written by Kohta NAKASHIMA.
(akpm: also uninline write_watchdog_counter(), saving 184 byets)
Signed-off-by: GOTO Masanori <gotom@sanori.org>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/aegl/linux-2.6:
[IA64] mca recovery return value when no bus check
[IA64] SGI SN drivers: don't report !sn2 hardware as an error
[IA64] don't report !sn2 or !summit hardware as an error
[IA64] gensparse_defconfig: turn on PNPACPI
[IA64] Increase severity of MCA recovery messages
When shifting the low-parts of signed numbers, a logical shift
should be used to avoid sign-extending a bit which isn't a sign
bit.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
A careful reading of the recent changes to the system call entry/exit
paths revealed several problems, plus some things that could be
simplified and improved:
* 32-bit wasn't testing the _TIF_NOERROR bit in the syscall fast exit
path, so it was only doing anything with it once it saw some other
bit being set. In other words, the noerror behaviour would apply to
the next system call where we had to reschedule or deliver a signal,
which is not necessarily the current system call.
* 32-bit wasn't doing the call to ptrace_notify in the syscall exit
path when the _TIF_SINGLESTEP bit was set.
* _TIF_RESTOREALL was in both _TIF_USER_WORK_MASK and
_TIF_PERSYSCALL_MASK, which is odd since _TIF_RESTOREALL is only set
by system calls. I took it out of _TIF_USER_WORK_MASK.
* On 64-bit, _TIF_RESTOREALL wasn't causing the non-volatile registers
to be restored (unless perhaps a signal was delivered or the syscall
was traced or single-stepped). Thus the non-volatile registers
weren't restored on exit from a signal handler. We probably got
away with it mostly because signal handlers written in C wouldn't
alter the non-volatile registers.
* On 32-bit I simplified the code and made it more like 64-bit by
making the syscall exit path jump to ret_from_except to handle
preemption and signal delivery.
* 32-bit was calling do_signal unnecessarily when _TIF_RESTOREALL was
set - but I think because of that 32-bit was actually restoring the
non-volatile registers on exit from a signal handler.
* I changed the order of enabling interrupts and saving the
non-volatile registers before calling do_syscall_trace_leave; now we
enable interrupts first.
Signed-off-by: Paul Mackerras <paulus@samba.org>
When there is no bus check, the return code should be failure, not success.
Signed-off-by: Russ Anderson (rja@sgi.com)
Signed-off-by: Tony Luck <tony.luck@intel.com>
This stuff is all in the generic ia64 kernel, and the new initcall error
reporting complains about them.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Turn on CONFIG_PNPACPI. I recently removed 8250_acpi.c. All devices
previously claimed by 8250_acpi.c should now be claimed by 8250_pnp.c.
This depends on having CONFIG_PNPACPI so ACPI devices show up as PNP
devices.
All other ia64 defconfigs either have CONFIG_PNPACPI already, or
don't have 8250 support turned on at all.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
The MCA recovery messages are currently KERN_DEBUG,
so they don't show up in /var/log/messages (by default).
Increase the severity to KERN_ERR, for the initial
message (and also add the physical address to this
message). Leave the successful isolation message as
KERN_DEBUG, but increase the severity when isolation
fails to KERN_CRIT.
[Russ' patch made these all KERN_CRIT]
Signed-off-by: Russ Anderson (rja@sgi.com)
Signed-off-by: Tony Luck <tony.luck@intel.com>
Patch from Alessandro Zummo
nas100d_power_exit(void) gets some protection
to avoid freeing an irq when it is not appropriate to do so.
Signed-off-by: Rod Whitby <rod@whitby.id.au>
Signed-off-by: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Catalin Marinas
Chapter B2.7.3 in the latest ARM ARM (with v6 information) states that
the completion of a TLB maintenance operation is only guaranteed by
the execution of a DSB (Data Syncronization Barrier, formerly Data
Write Barrier or Drain Write Buffer).
Note that a DSB is only needed in the flush_tlb_kernel_* functions
since the completion is guaranteed by a mode change (i.e. switching
back to user mode) for the flush_tlb_user_* functions.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch makes the kernel bootable again on ia32 EFI systems.
Signed-off-by: Edgar Hucek <hostmaster@ed-soft.at>
Cc: Matt Domsch <Matt_Domsch@dell.com>
Cc: Zachary Amsden <zach@vmware.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add the missing pm_power_off's for the h8300, v850 and xtensa
architectures.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Cc: Miles Bader <uclinux-v850@lsi.nec.co.jp>
Cc: Chris Zankel <chris@zankel.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Also from Thomas Gleixner <tglx@linutronix.de>
Function next_timer_interrupt() got broken with a recent patch
6ba1b91213 as sys_nanosleep() was moved to
hrtimer. This broke things as next_timer_interrupt() did not check hrtimer
tree for next event.
Function next_timer_interrupt() is needed with dyntick (CONFIG_NO_IDLE_HZ,
VST) implementations, as the system can be in idle when next hrtimer event
was supposed to happen. At least ARM and S390 currently use
next_timer_interrupt().
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
i386 timer_resume is updating jiffies, not jiffies_64. It looks there is a
potential overflow problem. And jiffies_64 and wall_jiffies should be
protected by xtime_lock.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Cc: john stultz <johnstul@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
We must use the "a" (allocate) attribute every time we
emit an entry into the __ex_table section.
For consistency, use "a" instead of #alloc which is some
Solaris compat cruft GNU as provides on Sparc.
Signed-off-by: David S. Miller <davem@davemloft.net>
yaboot is scrogged and calls us with an invalid stack alignment,
it seems.
Thanks to David Woodhouse to pointing me to the problem.
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
On Thu, 2006-03-02 at 19:55 +0100, Olaf Hering wrote:
> My iBook1 has 2 memory regions in reg. Depending on how I boot it
> (vmlinux+initrd) or zImage.initrd, it will not boot with current Linus
> tree.
> rmo_top should be 160MB instead of 32MB.
On logically-partitioned machines the first element of the reg
property in the memory node is defined to be the "RMO" region,
i.e. the memory that the processor can access in real mode. On other
machines the first element has no special meaning, so only take it to
be the RMO region on LPAR machines.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch makes userland aware of the icache snoop capability of the
POWER5 (and possibly others in the future) and of SMT capabilities.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The variable `timebase' used to transfer the current timebase value
from one cpu to the other in smp_core99_give/take_timebase was only
an unsigned long, i.e. 32 bits on 32-bit machines. It needs to be
64 bits. This makes it a u64, and fixes the issue reported by Kyle
Moffett, that the two cpus see wildly different values for the time
of day.
Signed-off-by: Paul Mackerras <paulus@samba.org>
This is along the lines suggested by Chris Lumens but goes further
in that it leaves the DEBUG symbol undefined, making the DBG macro
empty.
Signed-off-by: Paul Mackerras <paulus@samba.org>
On 32-bit, the exception prolog for the program check exception doesn't
enable interrupts early on. If it is an illegal instruction exception,
we read the instruction in order to emulate certain instructions, and
the get_user of the instruction triggers a WARN_ON since interrupts
are still disabled. This adds a local_irq_enable() to enable
interrupts before reading the instruction.
Signed-off-by: Paul Mackerras <paulus@samba.org>
The 'tick_usec' is USER_HZ period in usec. do_gettimeofday() should
use kernel HZ value.
Here is a patch for MIPS. It seems m32r, m68k and sparc have same
problem though their HZ and USER_HZ are same for now.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This patch adds mm->task_size to keep track of the task size of a given mm
and uses that to fix the powerpc vdso so that it uses the mm task size to
decide what pages to fault in instead of the current thread flags (which
broke when ptracing).
(akpm: I expect that mm_struct.task_size will become the way in which we
finally sort out the confusion between 32-bit processes and 32-bit mm's. It
may need tweaks, but at this stage this patch is powerpc-only.)
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This driver loops over 'num_online_cpus', but it doesn't account for holes
in the online map created by offlined cpus, and assumes that the cpu
numbers stay linear.
Signed-off-by: Dave Jones <davej@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Allow sysadmin to disable all warnings about userland apps
making unaligned accesses by using:
# echo 1 > /proc/sys/kernel/ignore-unaligned-usertrap
Rather than having to use prctl on a process by process basis.
Default behaivour leaves the warnings enabled.
Signed-off-by: Jes Sorensen <jes@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
When a CPU has no scache, the scache flushing functions currently
aren't getting initialized and the NULL pointer is eventually called
as a function. Initialize the scache flushing functions as a noop
when there's no scache.
Initial patch by me and most of the debugging done by Martin Michlmayr.
Signed-off-by: Martin Michlmayr <tbm@cyrius.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
beautify coding style for zeroing end of fsyscall_table entries.
Remove misleading __NR_syscall_last and add more comments.
Drop (now unneeded) "guard against failure to increase NR_syscalls"
Signed-off-by: Ken Chen <kenneth.w.chen@intel.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Before the merge I updated create_pte_mapping() to work for iSeries, by
calling iSeries_hpte_bolt_or_insert. (4c55130b2a)
Later we changed iSeries_hpte_insert to cope with the bolting case, and called
that instead from create_pte_mapping() (which was renamed to htab_bolt_mapping)
(3c726f8dee).
Unfortunately that change introduced a subtle bug, where we pass an absolute
address to iSeries_hpte_insert() where it expects a physical address. This
leads to us calling phys_to_abs() twice on the physical address, which is
seriously bogus.
This only causes a problem if the absolute address from the first translation
can be looked up again in the chunk_map, which depends on the size and layout
of memory. I've seen it fail on one box, but not others.
The minimal fix is to pass the physical address to iSeries_hpte_insert(). For
2.6.17 we should make phys_to_abs() BUG if we try to double-translate an
address.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
A bug in the assembly code of the vdso can cause gettimeofday() to hang
or to return incorrect results. The wrong register was used to test for
pending updates of the calibration variables and to create a dependency
for subsequent loads. This fixes it.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Some hotplug driver functions were migrated to the kernel for use by EEH
in commit 2bf6a8fa21.
Previously, the PCI Hotplug module had been changed to use the new
OFDT-based PCI probe when appropriate:
5fa80fcdca
When rpaphp_pci_config_slot() was moved from the rpaphp driver to the
new kernel function pcibios_add_pci_devices(), the OFDT-based probe
stuff was dropped. This patch restores it.
Signed-off-by: John Rose <johnrose@austin.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This reverts commit 13a229abc2.
Quoth Andi:
"After some consideration and feedback from various people it turns
out this wasn't that good an idea. It has some problems and needs
more work. Since it was only an optimization anyways it's best to
just back it out again for now."
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
arch/ia64/kernel/unaligned.c erroneously marked die_if_kernel()
with a "noreturn" attribute ... which is silly (it returns whenever
the argument regs say that the fault happened in user mode, as one
might expect given the "if_kernel" part of its name!). Thanks to
Alan and Gareth for pointing this out.
Signed-off-by: Tony Luck <tony.luck@intel.com>
Christoph Hellwig <hch@infradead.org> pointed that there are no
in-tree uses of this. So revert 9c65cb9be6
Signed-off-by: Tony Luck <tony.luck@intel.com>
pcibios_setup() should return NULL if it handled a parameter. Since ia64
handles no parameters, it should return the string that was passed in,
not NULL. This brings ia64 into line with all other architectures that
handle no parameters.
Signed-off-by: Matthew Wilcox <matthew@wil.cx>
Signed-off-by: Tony Luck <tony.luck@intel.com>
unaligned_access does fetch cr.ipsr, then calls
dispatch_unaligned_handler, but dispatch_unaligned_handler fetches
cr.ipsr again, so delete the first one.
Signed-off-by: Zhang Yanmin <yanmin.zhang@intel.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Not just cleanup but also fixes O32 readdir(2) emulation.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
A recent change requires cpu_possible_map to be initialized before
smp_sched_init() but most MIPS platforms were initializing their
processors in the prom_prepare_cpus callback of smp_prepare_cpus. The
simple fix of calling prom_prepare_cpus from one of the earlier SMP
initialization hooks doesn't work well either since IPIs may require
init_IRQ() to have completed, so bit the bullet and split
prom_prepare_cpus into two initialization functions, plat_smp_setup
which is called early from setup_arch and plat_prepare_cpus called where
prom_prepare_cpus used to be called.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The inline cputime_to_foo and foo_to_cputime conversion functions in
include/asm-powerpc/cputime.h refer to 5 variables, which need to be
exported if those functions are to be usable from modules.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Commit 9ec4b1f356 made kprobes not compile
without module support, so just make that clear in the Kconfig file.
Also, since it's marked EXPERIMENTAL, make that dependency explicit too.
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The change to kernel/sched.c's init code to use for_each_cpu()
requires that the cpu_possible_map be setup much earlier.
Set it up via setup_arch(), constrained to NR_CPUS, and later
constrain it to max_cpus in smp_prepare_cpus().
This fixes SMP booting on sparc64.
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 9c869edac5 broke voyager again
rather subtly because it already had its own topology exporting
functions, so now each CPU gets registered twice.
I think we can actually use the generic ones, so I don't propose
reverting it. The attached should eliminate the voyager topology
functions in favour of the generic ones.
I also added a define to ensure voyager is never hotplug CPU (we don't
have the support in the SMP harness).
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The commit e2c0388866 added
setup_additional_cpus to setup.c but this is only defined if
CONFIG_HOTPLUG_CPU is set. This patch changes the #ifdef to reflect that.
Signed-off-by: Brian Magnuson <magnuson@rcn.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The previous experiment for using apicmaintimer on ATI systems didn't
work out very well. In particular laptops with C2/C3 support often
don't let it tick during idle, which makes it useless. There were also
some other bugs that made the apicmaintimer often not used at all.
I tried some other experiments - running timer over RTC and some other
things but they didn't really work well neither.
I rechecked the specs now and it turns out this simple change is
actually enough to avoid the double ticks on the ATI systems. We just
turn off IRQ 0 in the 8254 and only route it directly using the IO-APIC.
I tested it on a few ATI systems and it worked there. In fact it worked
on all chipsets (NVidia, Intel, AMD, ATI) I tried it on.
According to the ACPI spec routing should always work through the
IO-APIC so I think it's the correct thing to do anyways (and most of the
old gunk in check_timer should be thrown away for x86-64).
But for 2.6.16 it's best to do a fairly minimal change:
- Use the known to be working everywhere-but-ATI IRQ0 both over 8254
and IO-APIC setup everywhere
- Except on ATI disable IRQ0 in the 8254
- Remove the code to select apicmaintimer on ATI chipsets
- Add some boot options to allow to override this (just paranoia)
In 2.6.17 I hope to switch the default over to this for everybody.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
SMP time selection originally ran after all CPUs were brought up because
it needed to know the number of CPUs to decide if it needs an MP safe
timer or not.
This is not needed anymore because we know present CPUs early.
This fixes a couple of problems:
- apicmaintimer didn't always work because it relied on state that was
set up time_init_gtod too late.
- The output for the used timer in early kernel log was misleading
because time_init_gtod could actually change it later. Now always
print the final timer choice
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
It didn't set up the CPU possible map early enough, so the
option didn't actually work.
Noticed by Heiko Carstens
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
[description from AK]
Old check for the IO-APIC watchdog during the timer check was wrong -
it obviously should only drop into this if the IO-APIC watchdog is used.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This makes x86-64 use the common X86_PM_TIMER Kconfig entry in drivers/acpi
And since PM timer is needed for correct timing on a lot of systems
now (e.g. AMD dual cores) and we often get bug reports from people
who forgot to set it make it depend on CONFIG_EMBEDDED. x86-64 had
this change before and it's a good thing.
I also fixed the description slightly to make this more clear.
Cc: len.brown@intel.com
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
[description from AK]
This fixes booting in APIC mode on some ACER laptops. x86-64
did a similar change some time ago.
See http://bugzilla.kernel.org/show_bug.cgi?id=4700 for details
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Big Unisys systems have multiple clusters too, but they have an
synchronized TSC.
I'm using the SMBIOS to check for vendor == IBM.
Cc: Chris McDermott <lcm@us.ibm.com>
Cc: "Protasevich, Natalie" <Natalie.Protasevich@unisys.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
In previous versions of pci-gart.c, no_iommu was used to determine if IOMMU was
disabled in the GART DMA mapping functions. This changed in 2.6.16 and now
gart_xxx() functions are only called if gart is enabled. Therefore, uses of
no_iommu in the GART code are no longer necessary and can be removed.
Also, it removes double deceleration of no_iommu and force_iommu in pci.h and
proto.h, by removing the deceleration in pci.h.
Lastly, end_pfn off by one error.
Tested (along with patch 1/2) on dual opteron with gart enabled, iommu=soft,
and iommu=off.
Signed-off-by: Jon Mason <jdmason@us.ibm.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Commit 9c869edac5 moved the i386 topology.c
file. That change broke x86-64 compiles, as it uses the same file.
Signed-off-by: Dave Jones <davej@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
mem= command line option was being ignored in arch/powerpc if we were not
a CONFIG_MULTIPLATFORM (which is handled via prom_init stub). The initial
command line extraction and parsing needed to be moved earlier in the boot
process and have code to actual parse mem= and do something about it.
Also, fixed a compile warning in the file.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Acked-by: Segher Boessenkool <segher@kernel.crashing.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
When compiling a non-default subarch, topology.c is missing from the kernel
build. This causes builds with CONFIG_HOTPLUG_CPU to fail. In addition,
on Intel processors with cpuid level > 4, it causes intel_cacheinfo.c to
reference uninitialized data that should have been set up by the initcall
in topology.c which calls register_cpu. This causes a kernel panic on boot
on newer Intel processors. Moving topology.c to arch/i386/kernel fixes
both of these problems.
Thanks to Dan Hecht for finding and fixing this problem.
Signed-off-by: Zachary Amsden <zach@vmware.com>
Signed-off-by: Dan Hecht <dhect@vmware.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
I'm currently at the POSIX meeting and one thing covered was the
incompatibility of Linux's link() with the POSIX definition. The name.
Linux does not follow symlinks, POSIX requires it does.
Even if somebody thinks this is a good default behavior we cannot change this
because it would break the ABI. But the fact remains that some application
might want this behavior.
We have one chance to help implementing this without breaking the behavior.
For this we could use the new linkat interface which would need a new
flags parameter. If the new parameter is AT_SYMLINK_FOLLOW the new
behavior could be invoked.
I do not want to introduce such a patch now. But we could add the
parameter now, just don't use it. The patch below would do this. Can we
get this late patch applied before the release more or less fixes the
syscall API?
Signed-off-by: Ulrich Drepper <drepper@redhat.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Recent GDT changes broke the SMP boot sequence if the booting CPU is
numbered anything other than zero. There's also a subtle source of error
in that the boot time CPU now uses cpu_gdt_table (which is actually the GDT
for booting CPUs in head.S). This patch fixes both problems by making GDT
descriptors themselves allocated from a per_cpu area and switching to them
in cpu_init(), which now means that cpu_gdt_table is exclusively used for
booting CPUs again.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Cc: Zachary Amsden <zach@vmware.com>
Cc: Matt Tolentino <metolent@snoqualmie.dp.intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Right at the moment (thanks to a patch from Andrew), cpu_possible_map on
voyager is CPU_MASK_NONE, which means the machine always thinks it has no
CPUs. Fix that by doing an early initialisation of the cpu_possible_map
from the cpu_phys_present_map.
(akpm: we aim to please)
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
It looks like I can't get away without exporting topology functions from
voyager any longer, so add them to the voyager subarchitecture.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix a problem seen on i686 machine with NX support where the instruction
could not be single stepped because of NX bit set on the memory pages
allocated by kprobes module. This patch provides allocation of instruction
solt so that the processor can execute the instruction from that location
similar to x86_64 architecture. Thanks to Bibo and Masami for testing this
patch.
Signed-off-by: Prasanna S Panchamukhi <prasanna@in.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Improve (especially for coherence) some prototypes, and return code of
init_cow_file in error case - for a short write return -EINVAL, otherwise
return the error we got!
Signed-off-by: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Acked-by: Jeff Dike <jdike@addtoit.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Do precise error handling: print precise error messages, distinguishing short
reads and read errors. This functions fails frequently enough for me so I
bothered doing this fix.
Signed-off-by: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Acked-by: Jeff Dike <jdike@addtoit.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix an fd leak and a return of -1 instead of -errno in the error path - this
showed up in intensive testing of HPPFS, the os_connect_socket user.
Signed-off-by: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Acked-by: Jeff Dike <jdike@addtoit.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Use __attribute_used__ instead of __attribute__ ((unused)). This will help
with GCC > 3.2.
Signed-off-by: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Acked-by: Jeff Dike <jdike@addtoit.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
To avoid conflicts, in kernel files errno is expanded to kernel_errno, to
distinguish it from glibc errno. In this case, the code wants to use the libc
errno but the kernel one is used; in the other usage, we return errno in place
of -errno in case of an error.
Signed-off-by: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Acked-by: Jeff Dike <jdike@addtoit.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Improve some error messages in the COW driver, and say V3, not V2, when
talking about V3 format. Also resync with our userspace code utility a bit
more.
Signed-off-by: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Acked-by: Jeff Dike <jdike@addtoit.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix and update for gcc-4.0.
- arch/m32r/kernel/signal.c:
Change type of the 8th parameter of sys_rt_sigsuspend() from
'struct pt_regs' to 'struct pt_regs *'.
This functions make use of the 'regs' parameter to return status value,
but gcc-4.0 optimizes and removes it as a dead code.
Functions, sys_sigaltstack() and sys_rt_sigreturn(), have also modified.
- arch/m32r/lib/usercopy.c, include/asm-m32r/uaccess.h:
Add early-clobber constraints('&') to output values of asm statements;
these constraints seems to be required for gcc-4.0 register assignment.
Signed-off-by: Hayato Fujiwara <fujiwara@linux-m32r.org>
Signed-off-by: Hirokazu Takata <takata@linux-m32r.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add -O2 option to AFLAGS to enable asm code optimization for m32r.
On m32r gas, "-m32r2 -O" option enables assembler's parallel code
generation optimization for M32R2 ISA as a default. So, "-no-parallel"
option is required explicitly for a cpu core with single instuction
issuing, for example, VDEC2.
Signed-off-by: Hirokazu Takata <takata@linux-m32r.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Patch from Andrew Victor
disable_irq() lazily disables the interrupt, so the IRQ is only disabled
once the interrupt occurs again. The GPIO interrupt handler therefore
must first check disable_depth to see if the IRQ needs to be disabled.
Orignal patch by Bill Gatliff.
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This implements accurate task and cpu time accounting for 64-bit
powerpc kernels. Instead of accounting a whole jiffy of time to a
task on a timer interrupt because that task happened to be running at
the time, we now account time in units of timebase ticks according to
the actual time spent by the task in user mode and kernel mode. We
also count the time spent processing hardware and software interrupts
accurately. This is conditional on CONFIG_VIRT_CPU_ACCOUNTING. If
that is not set, we do tick-based approximate accounting as before.
To get this accurate information, we read either the PURR (processor
utilization of resources register) on POWER5 machines, or the timebase
on other machines on
* each entry to the kernel from usermode
* each exit to usermode
* transitions between process context, hard irq context and soft irq
context in kernel mode
* context switches.
On POWER5 systems with shared-processor logical partitioning we also
read both the PURR and the timebase at each timer interrupt and
context switch in order to determine how much time has been taken by
the hypervisor to run other partitions ("steal" time). Unfortunately,
since we need values of the PURR on both threads at the same time to
accurately calculate the steal time, and since we can only calculate
steal time on a per-core basis, the apportioning of the steal time
between idle time (time which we ceded to the hypervisor in the idle
loop) and actual stolen time is somewhat approximate at the moment.
This is all based quite heavily on what s390 does, and it uses the
generic interfaces that were added by the s390 developers,
i.e. account_system_time(), account_user_time(), etc.
This patch doesn't add any new interfaces between the kernel and
userspace, and doesn't change the units in which time is reported to
userspace by things such as /proc/stat, /proc/<pid>/stat, getrusage(),
times(), etc. Internally the various task and cpu times are stored in
timebase units, but they are converted to USER_HZ units (1/100th of a
second) when reported to userspace. Some precision is therefore lost
but there should not be any accumulating error, since the internal
accumulation is at full precision.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Maple firmware does not need PCI resource allocation, and in fact, it
can cause problems in some strange cases.
Signed-off-by: Segher Boessenkool <segher@kernel.crashing.org>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Do disable, not enable, the HT APIC IRQ in the function that is
supposed to.
Enable the MPIC IRQ before enabling the downstream APIC IRQ, avoids
potentially losing an interrupt.
Signed-off-by: Segher Boessenkool <segher@kernel.crashing.org>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Update defconfigs for g5, pseries and generic ppc64. Default choices
for everything, with the following exceptions:
* Enable WINDFARM_PM112 on g5 and ppc64.
* Increase CONFIG_NR_CPUS to 4 in g5_defconfig
* CONFIG_TIGON3=y instead of =m in g5_defconfig
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Paul Mackerras <paulus@samba.org>
HMT support is currently broken and needs to be reworked to play nicely
with the SMT scheduler. Remove the bit rotten bits for the time being.
I also updated an incorrect comment, we enter __secondary_hold with the
physical cpu id in r3.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The runlatch SPR can take a lot of time to write. My original runlatch
code would set it on every exception entry even though most of the time
this was not required. It would also continually set it in the idle
loop, which is an issue on an SMT capable processor.
Now we cache the runlatch value in a threadinfo bit, and only check for
it in decrementer and hardware interrupt exceptions as well as the idle
loop. Boot on POWER3, POWER5 and iseries, and compile tested on pmac32.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
native_hpte_clear has a spinlock recursion problem with the native_tlbie_lock
being called twice, once in native_hpte_clear() and once within tlbie().
Fix the problem by changing the call to tlbie() in native_hpte_clear() to
__tlbie(). It still supports only 4k pages for now.
Signed-off-by: R Sharada <sharada@in.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Disable OProfile in Kconfig for iSeries to prevent hangs. OProfile
was not originally intended to work with legacy iSeries.
Signed-off-by: Kelly Daly <kelly@au.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
altivec_unavailable_exception is called without setting r3... it looks like
the r3 that actually gets passed in as struct pt_regs *regs is the
undisturbed value of r3 at the time the altivec instruction was encountered.
The user actually gets to choose the pt_regs printed in the Oops!
This fixes the oops by passing the correct pt_regs pointer to
altivec_unavailable_exception.
Signed-off-by: Alan Curry <pacman@TheWorld.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The panic CPU is waiting forever due to some large timeout value if some
CPU is not responding to an IPI.
This patch fixes the problem - the maximum waiting period will be
10 seconds and then the kdump boot will go ahead.
Signed-off-by: Haren Myneni <haren@us.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Fix up xmon compilation after the last change.
Remove lots of dead code, all the pmac and chrp support is in arch/powerpc
Signed-off-by: Olaf Hering <olh@suse.de>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Ralf Baechle
Paul Mackerras
Linus Torvalds
Andi Kleen
Christoph Lameter
Alessandro Zummo
Michael Matz
Shaohua Li
Gerald Schaefer
GOTO Masanori
Russell King
Russ Anderson
Bjorn Helgaas
Russ Anderson
Alessandro Zummo
Catalin Marinas
Edgar Hucek
Adrian Bunk
Tony Lindgren
Atsushi Nemoto
David S. Miller
Linus Torvalds
Benjamin Herrenschmidt
Dave Jones
Jes Sorensen
Kumar Gala
Ken Chen
Michael Ellerman
Olaf Hering
John Rose
Tony Luck
Christoph Hellwig
Matthew Wilcox
Zhang, Yanmin
Linus Torvalds
James Bottomley
Brian Magnuson
Chris McDermott
Andreas Deresch
Jon Mason
Zachary Amsden
Ulrich Drepper
Prasanna S Panchamukhi
Paolo 'Blaisorblade' Giarrusso
Hirokazu Takata
Andrew Victor
Segher Boessenkool
Olof Johansson
Anton Blanchard
R Sharada
Kelly Daly
Alan Curry
Haren Myneni