Move the callback into the phylink_config structure, rather than
providing a callback to set this up.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Tested-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
gro_cells lib is used by different encapsulating netdevices, such as
geneve, macsec, vxlan etc. to speed up decapsulated traffic processing.
CPU tag is a sort of "encapsulation", and we can use the same mechs to
greatly improve overall DSA performance.
skbs are passed to the GRO layer after removing CPU tags, so we don't
need any new packet offload types as it was firstly proposed by me in
the first GRO-over-DSA variant [1].
The size of struct gro_cells is sizeof(void *), so hot struct
dsa_slave_priv becomes only 4/8 bytes bigger, and all critical fields
remain in one 32-byte cacheline.
The other positive side effect is that drivers for network devices
that can be shipped as CPU ports of DSA-driven switches can now use
napi_gro_frags() to pass skbs to kernel. Packets built that way are
completely non-linear and are likely being dropped without GRO.
This was tested on to-be-mainlined-soon Ethernet driver that uses
napi_gro_frags(), and the overall performance was on par with the
variant from [1], sometimes even better due to minimal overhead.
net.core.gro_normal_batch tuning may help to push it to the limit
on particular setups and platforms.
iperf3 IPoE VLAN NAT TCP forwarding (port1.218 -> port0) setup
on 1.2 GHz MIPS board:
5.7-rc2 baseline:
[ID] Interval Transfer Bitrate Retr
[ 5] 0.00-120.01 sec 9.00 GBytes 644 Mbits/sec 413 sender
[ 5] 0.00-120.00 sec 8.99 GBytes 644 Mbits/sec receiver
Iface RX packets TX packets
eth0 7097731 7097702
port0 426050 6671829
port1 6671681 425862
port1.218 6671677 425851
With this patch:
[ID] Interval Transfer Bitrate Retr
[ 5] 0.00-120.01 sec 12.2 GBytes 870 Mbits/sec 122 sender
[ 5] 0.00-120.00 sec 12.2 GBytes 870 Mbits/sec receiver
Iface RX packets TX packets
eth0 9474792 9474777
port0 455200 353288
port1 9019592 455035
port1.218 353144 455024
v2:
- Add some performance examples in the commit message;
- No functional changes.
[1] https://lore.kernel.org/netdev/20191230143028.27313-1-alobakin@dlink.ru/
Signed-off-by: Alexander Lobakin <bloodyreaper@yandex.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is no reason to fail the probing of the switch if the MTU couldn't
be configured correctly (either the switch port itself, or the host
port) for whatever reason. MTU-sized traffic probably won't work, sure,
but we can still probably limp on and support some form of communication
anyway, which the users would probably appreciate more.
Fixes: bfcb813203 ("net: dsa: configure the MTU for switch ports")
Reported-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes: f41071407c85 ("net: dsa: implement auto-normalization of MTU for bridge hardware datapath")
Signed-off-by: kbuild test robot <lkp@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix an oops in dsa_port_phylink_mac_change() caused by a combination
of a20f997010 ("net: dsa: Don't instantiate phylink for CPU/DSA
ports unless needed") and the net-dsa-improve-serdes-integration
series of patches 65b7a2c8e3 ("Merge branch
'net-dsa-improve-serdes-integration'").
Unable to handle kernel NULL pointer dereference at virtual address 00000124
pgd = c0004000
[00000124] *pgd=00000000
Internal error: Oops: 805 [#1] SMP ARM
Modules linked in: tag_edsa spi_nor mtd xhci_plat_hcd mv88e6xxx(+) xhci_hcd armada_thermal marvell_cesa dsa_core ehci_orion libdes phy_armada38x_comphy at24 mcp3021 sfp evbug spi_orion sff mdio_i2c
CPU: 1 PID: 214 Comm: irq/55-mv88e6xx Not tainted 5.6.0+ #470
Hardware name: Marvell Armada 380/385 (Device Tree)
PC is at phylink_mac_change+0x10/0x88
LR is at mv88e6352_serdes_irq_status+0x74/0x94 [mv88e6xxx]
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The approach taken to pass the port policer methods on to drivers is
pragmatic. It is similar to the port mirroring implementation (in that
the DSA core does all of the filter block interaction and only passes
simple operations for the driver to implement) and dissimilar to how
flow-based policers are going to be implemented (where the driver has
full control over the flow_cls_offload data structure).
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make room for other actions for the matchall filter by keeping the
mirred argument parsing self-contained in its own function.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Many switches don't have an explicit knob for configuring the MTU
(maximum transmission unit per interface). Instead, they do the
length-based packet admission checks on the ingress interface, for
reasons that are easy to understand (why would you accept a packet in
the queuing subsystem if you know you're going to drop it anyway).
So it is actually the MRU that these switches permit configuring.
In Linux there only exists the IFLA_MTU netlink attribute and the
associated dev_set_mtu function. The comments like to play blind and say
that it's changing the "maximum transfer unit", which is to say that
there isn't any directionality in the meaning of the MTU word. So that
is the interpretation that this patch is giving to things: MTU == MRU.
When 2 interfaces having different MTUs are bridged, the bridge driver
MTU auto-adjustment logic kicks in: what br_mtu_auto_adjust() does is it
adjusts the MTU of the bridge net device itself (and not that of the
slave net devices) to the minimum value of all slave interfaces, in
order for forwarded packets to not exceed the MTU regardless of the
interface they are received and send on.
The idea behind this behavior, and why the slave MTUs are not adjusted,
is that normal termination from Linux over the L2 forwarding domain
should happen over the bridge net device, which _is_ properly limited by
the minimum MTU. And termination over individual slave devices is
possible even if those are bridged. But that is not "forwarding", so
there's no reason to do normalization there, since only a single
interface sees that packet.
The problem with those switches that can only control the MRU is with
the offloaded data path, where a packet received on an interface with
MRU 9000 would still be forwarded to an interface with MRU 1500. And the
br_mtu_auto_adjust() function does not really help, since the MTU
configured on the bridge net device is ignored.
In order to enforce the de-facto MTU == MRU rule for these switches, we
need to do MTU normalization, which means: in order for no packet larger
than the MTU configured on this port to be sent, then we need to limit
the MRU on all ports that this packet could possibly come from. AKA
since we are configuring the MRU via MTU, it means that all ports within
a bridge forwarding domain should have the same MTU.
And that is exactly what this patch is trying to do.
>From an implementation perspective, we try to follow the intent of the
user, otherwise there is a risk that we might livelock them (they try to
change the MTU on an already-bridged interface, but we just keep
changing it back in an attempt to keep the MTU normalized). So the MTU
that the bridge is normalized to is either:
- The most recently changed one:
ip link set dev swp0 master br0
ip link set dev swp1 master br0
ip link set dev swp0 mtu 1400
This sequence will make swp1 inherit MTU 1400 from swp0.
- The one of the most recently added interface to the bridge:
ip link set dev swp0 master br0
ip link set dev swp1 mtu 1400
ip link set dev swp1 master br0
The above sequence will make swp0 inherit MTU 1400 as well.
Suggested-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It is useful be able to configure port policers on a switch to accept
frames of various sizes:
- Increase the MTU for better throughput from the default of 1500 if it
is known that there is no 10/100 Mbps device in the network.
- Decrease the MTU to limit the latency of high-priority frames under
congestion, or work around various network segments that add extra
headers to packets which can't be fragmented.
For DSA slave ports, this is mostly a pass-through callback, called
through the regular ndo ops and at probe time (to ensure consistency
across all supported switches).
The CPU port is called with an MTU equal to the largest configured MTU
of the slave ports. The assumption is that the user might want to
sustain a bidirectional conversation with a partner over any switch
port.
The DSA master is configured the same as the CPU port, plus the tagger
overhead. Since the MTU is by definition L2 payload (sans Ethernet
header), it is up to each individual driver to figure out if it needs to
do anything special for its frame tags on the CPU port (it shouldn't
except in special cases). So the MTU does not contain the tagger
overhead on the CPU port.
However the MTU of the DSA master, minus the tagger overhead, is used as
a proxy for the MTU of the CPU port, which does not have a net device.
This is to avoid uselessly calling the .change_mtu function on the CPU
port when nothing should change.
So it is safe to assume that the DSA master and the CPU port MTUs are
apart by exactly the tagger's overhead in bytes.
Some changes were made around dsa_master_set_mtu(), function which was
now removed, for 2 reasons:
- dev_set_mtu() already calls dev_validate_mtu(), so it's redundant to
do the same thing in DSA
- __dev_set_mtu() returns 0 if ops->ndo_change_mtu is an absent method
That is to say, there's no need for this function in DSA, we can safely
call dev_set_mtu() directly, take the rtnl lock when necessary, and just
propagate whatever errors get reported (since the user probably wants to
be informed).
Some inspiration (mainly in the MTU DSA notifier) was taken from a
vaguely similar patch from Murali and Florian, who are credited as
co-developers down below.
Co-developed-by: Murali Krishna Policharla <murali.policharla@broadcom.com>
Signed-off-by: Murali Krishna Policharla <murali.policharla@broadcom.com>
Co-developed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
flow_action_hw_stats_types_check() helper takes one of the
FLOW_ACTION_HW_STATS_*_BIT values as input. If we align
the arguments to the opening bracket of the helper there
is no way to call this helper and stay under 80 characters.
Remove the "types" part from the new flow_action helpers
and enum values.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce flow_action_basic_hw_stats_types_check() helper and use it
in drivers. That sanitizes the drivers which do not have support
for action HW stats types.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Due to the immense variety of classification keys and actions available
for tc-flower, as well as due to potentially very different DSA switch
capabilities, it doesn't make a lot of sense for the DSA mid layer to
even attempt to interpret these. So just pass them on to the underlying
switch driver.
DSA implements just the standard boilerplate for binding and unbinding
flow blocks to ports, since nobody wants to deal with that.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Place phylink_start()/phylink_stop() inside dsa_port_enable() and
dsa_port_disable(), which ensures that we call phylink_stop() before
tearing down phylink - which is a documented requirement. Failure
to do so can cause use-after-free bugs.
Fixes: 0e27921816 ("net: dsa: Use PHYLINK for the CPU/DSA ports")
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
It is possible to stack multiple DSA switches in a way that they are not
part of the tree (disjoint) but the DSA master of a switch is a DSA
slave of another. When that happens switch drivers may have to know this
is the case so as to determine whether their tagging protocol has a
remove chance of working.
This is useful for specific switch drivers such as b53 where devices
have been known to be stacked in the wild without the Broadcom tag
protocol supporting that feature. This allows b53 to continue supporting
those devices by forcing the disabling of Broadcom tags on the outermost
switches if necessary.
The get_tag_protocol() function is therefore updated to gain an
additional enum dsa_tag_protocol argument which denotes the current
tagging protocol used by the DSA master we are attached to, else
DSA_TAG_PROTO_NONE for the top of the dsa_switch_tree.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are 3 things that are wrong with the DSA deferred xmit mechanism:
1. Its introduction has made the DSA hotpath ever so slightly more
inefficient for everybody, since DSA_SKB_CB(skb)->deferred_xmit needs
to be initialized to false for every transmitted frame, in order to
figure out whether the driver requested deferral or not (a very rare
occasion, rare even for the only driver that does use this mechanism:
sja1105). That was necessary to avoid kfree_skb from freeing the skb.
2. Because L2 PTP is a link-local protocol like STP, it requires
management routes and deferred xmit with this switch. But as opposed
to STP, the deferred work mechanism needs to schedule the packet
rather quickly for the TX timstamp to be collected in time and sent
to user space. But there is no provision for controlling the
scheduling priority of this deferred xmit workqueue. Too bad this is
a rather specific requirement for a feature that nobody else uses
(more below).
3. Perhaps most importantly, it makes the DSA core adhere a bit too
much to the NXP company-wide policy "Innovate Where It Doesn't
Matter". The sja1105 is probably the only DSA switch that requires
some frames sent from the CPU to be routed to the slave port via an
out-of-band configuration (register write) rather than in-band (DSA
tag). And there are indeed very good reasons to not want to do that:
if that out-of-band register is at the other end of a slow bus such
as SPI, then you limit that Ethernet flow's throughput to effectively
the throughput of the SPI bus. So hardware vendors should definitely
not be encouraged to design this way. We do _not_ want more
widespread use of this mechanism.
Luckily we have a solution for each of the 3 issues:
For 1, we can just remove that variable in the skb->cb and counteract
the effect of kfree_skb with skb_get, much to the same effect. The
advantage, of course, being that anybody who doesn't use deferred xmit
doesn't need to do any extra operation in the hotpath.
For 2, we can create a kernel thread for each port's deferred xmit work.
If the user switch ports are named swp0, swp1, swp2, the kernel threads
will be named swp0_xmit, swp1_xmit, swp2_xmit (there appears to be a 15
character length limit on kernel thread names). With this, the user can
change the scheduling priority with chrt $(pidof swp2_xmit).
For 3, we can actually move the entire implementation to the sja1105
driver.
So this patch deletes the generic implementation from the DSA core and
adds a new one, more adequate to the requirements of PTP TX
timestamping, in sja1105_main.c.
Suggested-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Before this change of_get_phy_mode() returned an enum,
phy_interface_t. On error, -ENODEV etc, is returned. If the result of
the function is stored in a variable of type phy_interface_t, and the
compiler has decided to represent this as an unsigned int, comparision
with -ENODEV etc, is a signed vs unsigned comparision.
Fix this problem by changing the API. Make the function return an
error, or 0 on success, and pass a pointer, of type phy_interface_t,
where the phy mode should be stored.
v2:
Return with *interface set to PHY_INTERFACE_MODE_NA on error.
Add error checks to all users of of_get_phy_mode()
Fixup a few reverse christmas tree errors
Fixup a few slightly malformed reverse christmas trees
v3:
Fix 0-day reported errors.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The only slightly tricky merge conflict was the netdevsim because the
mutex locking fix overlapped a lot of driver reload reorganization.
The rest were (relatively) trivial in nature.
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds glue logic to make pause settings per port
configurable vie ethtool.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some interface types could be nested.
(VLAN, BONDING, TEAM, MACSEC, MACVLAN, IPVLAN, VIRT_WIFI, VXLAN, etc..)
These interface types should set lockdep class because, without lockdep
class key, lockdep always warn about unexisting circular locking.
In the current code, these interfaces have their own lockdep class keys and
these manage itself. So that there are so many duplicate code around the
/driver/net and /net/.
This patch adds new generic lockdep keys and some helper functions for it.
This patch does below changes.
a) Add lockdep class keys in struct net_device
- qdisc_running, xmit, addr_list, qdisc_busylock
- these keys are used as dynamic lockdep key.
b) When net_device is being allocated, lockdep keys are registered.
- alloc_netdev_mqs()
c) When net_device is being free'd llockdep keys are unregistered.
- free_netdev()
d) Add generic lockdep key helper function
- netdev_register_lockdep_key()
- netdev_unregister_lockdep_key()
- netdev_update_lockdep_key()
e) Remove unnecessary generic lockdep macro and functions
f) Remove unnecessary lockdep code of each interfaces.
After this patch, each interface modules don't need to maintain
their lockdep keys.
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
DSA currently handles shared block filters (for the classifier-action
qdisc) in the core due to what I believe are simply pragmatic reasons -
hiding the complexity from drivers and offerring a simple API for port
mirroring.
Extend the dsa_slave_setup_tc function by passing all other qdisc
offloads to the driver layer, where the driver may choose what it
implements and how. DSA is simply a pass-through in this case.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Acked-by: Kurt Kanzenbach <kurt@linutronix.de>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
When adding a VLAN sub-interface on a DSA slave port, the 8021q core
checks NETIF_F_HW_VLAN_CTAG_FILTER and, if the netdev is capable of
filtering, calls .ndo_vlan_rx_add_vid or .ndo_vlan_rx_kill_vid to
configure the VLAN offloading.
DSA sets this up counter-intuitively: it always advertises this netdev
feature, but the underlying driver may not actually support VLAN table
manipulation. In that case, the DSA core is forced to ignore the error,
because not being able to offload the VLAN is still fine - and should
result in the creation of a non-accelerated VLAN sub-interface.
Change this so that the netdev feature is only advertised for switch
drivers that support VLAN manipulation, instead of checking for
-EOPNOTSUPP at runtime.
Suggested-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the bridge offloads a VLAN on a slave port, we also need to
program its dedicated CPU port as a member of the VLAN.
Drivers may handle the CPU port's membership as they want. For example,
Marvell as a special "Unmodified" mode to pass frames as is through
such ports.
Even though DSA expects the drivers to handle the CPU port membership,
it does not make sense to program user VLANs as PVID on the CPU port.
This patch clears this flag before programming the CPU port.
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Suggested-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
DSA currently programs a VLAN on the CPU port implicitly after the
related notifier is received by a switch.
While we still need to do this transparent programmation of the DSA
links in the fabric, programming the CPU port this way may cause
problems in some corners such as the tag_8021q driver.
Because the dedicated CPU port is specific to a slave, make their
programmation explicit a few layers up, in the slave code.
Note that technically, DSA links have a dedicated CPU port as well,
but since they are only used as conduit between interconnected switches
of a fabric, programming them transparently this way is what we want.
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The bridge VLANs are not offloaded by dsa_port_vlan_* if the port is
not bridged or if its bridge is not VLAN aware.
This is a good thing but other corners of DSA, such as the tag_8021q
driver, may need to program VLANs regardless the bridge state.
And also because bridge_dev is specific to user ports anyway, move
these checks were it belongs, one layer up in the slave code.
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Suggested-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add dsa_slave_vlan_add and dsa_slave_vlan_del helpers to handle
SWITCHDEV_OBJ_ID_PORT_VLAN switchdev objects. Also copy the
switchdev_obj_port_vlan structure on add since we will modify it in
future patches.
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently dsa_port_vid_add returns 0 if the switch returns -EOPNOTSUPP.
This function is used in the tag_8021q.c code to offload the PVID of
ports, which would simply not work if .port_vlan_add is not supported
by the underlying switch.
Do not skip -EOPNOTSUPP in dsa_port_vid_add but only when necessary,
that is to say in dsa_slave_vlan_rx_add_vid.
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This object stores the flow block callbacks that are attached to this
block. Update flow_block_cb_lookup() to take this new object.
This patch restores the block sharing feature.
Fixes: da3eeb904f ("net: flow_offload: add list handling functions")
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rename this type definition and adapt users.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
No need to annotate the netns on the flow block callback object,
flow_block_cb_is_busy() already checks for used blocks.
Fixes: d63db30c85 ("net: flow_offload: add flow_block_cb_alloc() and flow_block_cb_free()")
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for enabling or disabling the flooding of
unknown multicast traffic on the CPU ports, depending on the value
of the switchdev SWITCHDEV_ATTR_ID_BRIDGE_MROUTER attribute.
The current behavior is kept unchanged but a user can now prevent
the CPU conduit to be flooded with a lot of unregistered traffic that
the network stack needs to filter in software with e.g.:
echo 0 > /sys/class/net/br0/multicast_router
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds a function to check if flow block callback is already in
use. Call this new function from flow_block_cb_setup_simple() and from
drivers.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch updates flow_block_cb_setup_simple() to use the flow block API.
Several drivers are also adjusted to use it.
This patch introduces the per-driver list of flow blocks to account for
blocks that are already in use.
Remove tc_block_offload alias.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rename from TCF_BLOCK_BINDER_TYPE_* to FLOW_BLOCK_BINDER_TYPE_* and
remove temporary tcf_block_binder_type alias.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rename from TC_BLOCK_{UN}BIND to FLOW_BLOCK_{UN}BIND and remove
temporary tc_block_command alias.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Get rid of the dsa_slave_switchdev_port_{attr_set,obj}_event functions
in favor of the switchdev_handle_port_{attr_set,obj_add,obj_del}
helpers which recurse into the lower devices of the target interface.
This has the benefit of being aware of the operations made on the
bridge device itself, where orig_dev is the bridge, and dev is the
slave. This can be used later to configure the hardware switches.
Only VLAN and (port) MDB objects not directly targeting the slave
device are unsupported at the moment, so skip this case in their
respective case statements.
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The switchdev handle helpers make use of a device checking helper
requiring a const net_device. Make dsa_slave_dev_check compliant
to this.
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For drivers that use deferred_xmit for PTP frames (such as sja1105),
there is no need to perform matching between PTP frames and their egress
timestamps, since the sending process can be serialized.
In that case, it makes sense to have the pointer to the skb clone that
DSA made directly in the skb->cb. It will be used for pushing the egress
timestamp back in the application socket's error queue.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some ISDN files that got removed in net-next had some changes
done in mainline, take the removals.
Signed-off-by: David S. Miller <davem@davemloft.net>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 3029 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190527070032.746973796@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In order to have a common handling of PHYLINK for the slave and non-user
ports, the DSA core glue logic (between PHYLINK and the driver) must use
an API that does not rely on a struct net_device.
These will also be called by the CPU-port-handling code in a further
patch.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Suggested-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The phylink_config structure will encapsulate a pointer to a struct
device and the operation type requested for this instance of PHYLINK.
This patch does not make any functional changes, it just transitions the
PHYLINK internals and all its users to the new API.
A pointer to a phylink_config structure will be passed to
phylink_create() instead of the net_device directly. Also, the same
phylink_config pointer will be passed back to all phylink_mac_ops
callbacks instead of the net_device. Using this mechanism, a PHYLINK
user can get the original net_device using a structure such as
'to_net_dev(config->dev)' or directly the structure containing the
phylink_config using a container_of call.
At the moment, only the PHYLINK_NETDEV is defined as a valid operation
type for PHYLINK. In this mode, a valid reference to a struct device
linked to the original net_device should be passed to PHYLINK through
the phylink_config structure.
This API changes is mainly driven by the necessity of adding a new
operation type in PHYLINK that disconnects the phy_device from the
net_device and also works when the net_device is lacking.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Tested-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The sk_buff control block can have any contents on xmit put there by the
stack, so initialization is mandatory, since we are checking its value
after the actual DSA xmit (the tagger may have changed it).
The DSA_SKB_ZERO() macro could have been used for this purpose, but:
- Zeroizing a 48-byte memory region in the hotpath is best avoided.
- It would have triggered a warning with newer compilers since
__dsa_skb_cb contains a structure within a structure, and the {0}
initializer was incorrect for that purpose.
So simply remove the DSA_SKB_ZERO() macro and initialize the
deferred_xmit variable by hand (which should be done for all further
dsa_skb_cb variables which need initialization - currently none - to
avoid the performance penalty).
Fixes: 97a69a0dea ("net: dsa: Add support for deferred xmit")
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There was NVMEM support added to of_get_mac_address, so it could now
return ERR_PTR encoded error values, so we need to adjust all current
users of of_get_mac_address to this new fact.
While at it, remove superfluous is_valid_ether_addr as the MAC address
returned from of_get_mac_address is always valid and checked by
is_valid_ether_addr anyway.
Fixes: d01f449c00 ("of_net: add NVMEM support to of_get_mac_address")
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Tested-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some hardware needs to take work to get convinced to receive frames on
the CPU port (such as the sja1105 which takes temporary L2 forwarding
rules over SPI that last for a single frame). Such work needs a
sleepable context, and because the regular .ndo_start_xmit is atomic,
this cannot be done in the tagger. So introduce a generic DSA mechanism
that sets up a transmit skb queue and a workqueue for deferred
transmission.
The new driver callback (.port_deferred_xmit) is in dsa_switch and not
in the tagger because the operations that require sleeping typically
also involve interacting with the hardware, and not simply skb
manipulations. Therefore having it there simplifies the structure a bit
and makes it unnecessary to export functions from the driver to the
tagger.
The driver is responsible of calling dsa_enqueue_skb which transfers it
to the master netdevice. This is so that it has a chance of performing
some more work afterwards, such as cleanup or TX timestamping.
To tell DSA that skb xmit deferral is required, I have thought about
changing the return type of the tagger .xmit from struct sk_buff * into
a enum dsa_tx_t that could potentially encode a DSA_XMIT_DEFER value.
But the trailer tagger is reallocating every skb on xmit and therefore
making a valid use of the pointer return value. So instead of reworking
the API in complicated ways, right now a boolean property in the newly
introduced DSA_SKB_CB is set.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Updates dsa hardware switch handling infrastructure to use the newer
intermediate representation for flow actions in matchall offloads.
Signed-off-by: Pieter Jansen van Vuuren <pieter.jansenvanvuuren@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This hides the need to perform a two-phase transaction and construct a
switchdev_obj_port_vlan struct.
Call graph (including a function that will be introduced in a follow-up
patch) looks like this now (same for the *_vlan_del function):
dsa_slave_vlan_rx_add_vid dsa_port_setup_8021q_tagging
| |
| |
| +-------------+
| |
v v
dsa_port_vid_add dsa_slave_port_obj_add
| |
+-------+ +-------+
| |
v v
dsa_port_vlan_add
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pass the switch ID down the to devlink through devlink_port_attrs_set()
so it can be used by devlink_compat_switch_id_get(). Leave
ndo_get_port_parent_id implementation only for legacy.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Before creating a slave netdevice, get the mac address from DTS and
apply in case it is valid.
Signed-off-by: Xiaofei Shen <xiaofeis@codeaurora.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller
Russell King
Alexander Lobakin
Vladimir Oltean
kbuild test robot
Jakub Kicinski
Jiri Pirko
Florian Fainelli
Vladimir Oltean
Andrew Lunn
Heiner Kallweit
Taehee Yoo
Vivien Didelot
Pablo Neira Ayuso
Thomas Gleixner
Ioana Ciornei
Petr Štetiar
Pieter Jansen van Vuuren
Xiaofei Shen