This change only affects experimental AoE storage networks.
It modifies the console message about runt packets detected so that the
AoE major and minor addresses of the AoE target that generated the runt
are mentioned.
Signed-off-by: Ed Cashin <ecashin@coraid.com>
Cc: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
With this change, the aoe driver treats the value zero as special for
the aoe_deadsecs module parameter. Normally, this value specifies the
number of seconds during which the driver will continue to attempt
retransmits to an unresponsive AoE target. After aoe_deadsecs has
elapsed, the aoe driver marks the aoe device as "down" and fails all
I/O.
The new meaning of an aoe_deadsecs of zero is for the driver to
retransmit commands indefinitely.
Signed-off-by: Ed Cashin <ecashin@coraid.com>
Cc: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Many AoE targets have four or fewer network ports, but some existing
storage devices have many, and the AoE protocol sets no limit.
This patch allows the use of more than eight remote MAC addresses per AoE
target, while reducing the amount of memory used by the aoe driver in
cases where there are many AoE targets with fewer than eight MAC addresses
each.
Signed-off-by: Ed Cashin <ecashin@coraid.com>
Cc: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
An AoE target can have multiple network ports used for AoE, and in the
aoe driver, those are tracked by the aoetgt struct. These changes allow
the aoe driver to handle network paths, or aoetgts, that are not working
well, compared to the others.
Paths that do not get responses despite the retransmission of AoE
commands are marked as "tainted", and non-tainted paths are preferred.
Meanwhile, the aoe driver attempts to "probe" the tainted path in the
background by issuing reads of LBA 0 that are padded out to full
(possibly jumbo-frame) size. If the probes get responses, then the path
is "redeemed", and its taint is removed.
This mechanism has been shown to be helpful in transparently handling
and recovering from real-world network "brown outs" in ways that the
earlier "shoot the help-needing target in the head" mechanism could not.
Signed-off-by: Ed Cashin <ecashin@coraid.com>
Cc: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
There is no need to call the request handler function in the I/O
completion routine. The user impact of not doing it is a more "nice" aoe
driver that is less susceptible to causing soft lockups.
Signed-off-by: Ed Cashin <ecashin@coraid.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The aoe driver will never be waiting for more than aoe_maxout AoE
commands from a given remote network port on an AoE target. Increasing
the cap increases performance. Users can tighten the setting to reduce
the amount of memory used for handling AoE traffic or the network
bandwidth used for AoE.
Signed-off-by: Ed Cashin <ecashin@coraid.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Commit f3b8e07af774 ("aoe: commands in retransmit queue use new
destination on failure") omits the copying of the coarse-grained time
when an AoE command was sent during the failover from one destination
MAC address on the AoE target to another.
The coarse-grained timing is only used when the system time changes or
an unlikely length of time has passed since the sending of the AoE
command. Users will not be impacted unless their system clock is very
inaccurate or something unusual (e.g., 10 GbE link reset) happens during
the period when the aoe driver is handling the failure of a port on the
AoE target. Being effected will mean that an AoE target could be
considered "down" too eagerly.
Signed-off-by: Ed Cashin <ecashin@coraid.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When one remote MAC address isn't working as a destination for AoE
commands, the frames used to track information associated with the AoE
commands are moved to a new aoetgt (defined by the tuple of {AoE major,
AoE minor, target MAC address}).
This patch makes sure that the frames on the queue for retransmits that
need to be done are updated to use the new destination, so that
retransmits will be sent through a working network path.
Without this change, packets on the retransmit queue will be needlessly
retransmitted to the unresponsive destination MAC, possibly causing
premature target failure before there's time for the retransmit timer to
run again, decide to retransmit again, and finally update the destination
to a working MAC address on the AoE target.
Signed-off-by: Ed Cashin <ecashin@coraid.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
These changes improve the accuracy of the decision about whether it's time
to retransmit an AoE command by using the microsecond-resolution
gettimeofday instead of jiffies.
Because the system time can jump suddenly, the decision reverts to using
jiffies if the high-resolution time difference is relatively large.
Otherwise the AoE targets could be considered failed inappropriately.
Signed-off-by: Ed Cashin <ecashin@coraid.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
With this bugfix in place the calculation of the criterion for "lateness"
is performed under lock. Without the lock, there is a chance that one of
the non-atomic operations performed on the round trip time statistics
could be incomplete, such that an incorrect lateness criterion would be
calculated.
Without this change, the effect of the bug would be rare unecessary but
benign retransmissions.
Signed-off-by: Ed Cashin <ecashin@coraid.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The /dev/etherd/err character device provides low-level information about
normal but sometimes interesting AoE command retransmits and "unexpected
responses", i.e., responses for packets that have already been
retransmitted.
This change adds MAC addresses to the messages about unexpected responses,
so that when they occur, it's more easy to determine the network paths to
which they belong.
Signed-off-by: Ed Cashin <ecashin@coraid.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The aoe driver already had some congestion handling, but it was limited in
its ability to cope with the kind of congestion that can arise on more
complex networks such as those involving paths through multiple ethernet
switches.
Some of the lessons from TCP's history of development can be applied to
improving the congestion control and avoidance on AoE storage networks.
These changes use familar concepts from Van Jacobson's "Congestion
Avoidance and Control" paper from '88, without adding significant
overhead.
This patch depends on an upcoming patch that covers the failover case when
AoE commands being retransmitted are transferred from one retransmit queue
to another. Another upcoming patch increases the timing accuracy.
Signed-off-by: Ed Cashin <ecashin@coraid.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Make the aoe driver follow expected behavior when the user uses ioctl to
get the ATA device identify information, allowing access to model, serial
number, etc.
Signed-off-by: Ed Cashin <ecashin@coraid.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The ATA over Ethernet config query response contains a "buffer count"
field reflecting the AoE target's capacity to buffer incoming AoE
commands.
By taking the current value of this field into accound, we increase
performance throughput or avoid network congestion, when the value
has increased or decreased, respectively.
Signed-off-by: Ed Cashin <ecashin@coraid.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Calling the request handler directly on a plugged queue defeats
the performance improvements provided by the plugging mechanism.
Use the __blk_run_queue function instead of calling the request
handler directly, so that we don't interfere with the block
layer's ability to plug the queue.
Signed-off-by: Ed Cashin <ecashin@coraid.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
In general, specific is better when it comes to messages about AoE usage
problems. Also, explicit checks for the AoE broadcast addresses are
added.
Signed-off-by: Ed Cashin <ecashin@coraid.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The ATA over Ethernet protocol uses a major (shelf) and minor (slot)
address to identify a particular storage target. These changes remove an
artificial limitation the aoe driver imposes on the use of AoE addresses.
For example, without these changes, the slot address has a maximum of 15,
but users commonly use slot numbers much greater than that.
The AoE shelf and slot address space is often used sparsely. Instead of
using a static mapping between AoE addresses and the block device minor
number, the block device minor numbers are now allocated on demand.
Signed-off-by: Ed Cashin <ecashin@coraid.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This change removes some unused code and attempts to increase code
consistency.
Signed-off-by: Ed Cashin <ecashin@coraid.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This change eliminates the danger that the user could rmmod the driver for
a network interface that is being used for AoE by the aoe driver.
Signed-off-by: Ed Cashin <ecashin@coraid.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In the driver code, "target" and aoetgt refer to a particular remote
interface on the AoE storage target. The latter is identified by its AoE
major and minor addresses. Commands that are being sent to an AoE storage
target {major, minor} can be sent or retransmitted to any of the remote
MAC addresses associated with the AoE storage target.
That is, frames are naturally associated with not an aoetgt (AoE major,
AoE minor, remote MAC address) but an aoedev (AoE major, AoE minor).
Making the code reflect that reality simplifies the driver, especially
when the path to a remote MAC address becomes unusable.
Signed-off-by: Ed Cashin <ecashin@coraid.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
A guard is inserted to prevent AoE minor addresses (slot addresses) higher
than 15 to be used, as they are not yet supported by the driver.
There is a change coming that will allow the aoe driver to overcome this
limit by using system device minor numbers dynamically, but until then,
this guard prevents unexpected targets from being used by the driver when
AoE targets with high minor numbers are on the AoE network.
Signed-off-by: Ed Cashin <ecashin@coraid.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The aoe_deadsecs module parameter allows the user to specify a hard limit
on the number of seconds an AoE command can be retransmitted before the
AoE block device is considered to have failed.
Using aoe_deadsecs to determine the time we try using a different remote
interface helps to ensure that the hard limit is not reached before we've
tried to recover by sending to a different remote port.
As a data storage target, the AoE target is unambiguously identified by
its {major, minor} AoE address tuple, and an AoE target can have multiple
MAC addresses. However, note that "target" in the driver code and
comments means a {major, minor, MAC address} tuple, as in "somewhere to
send packets".
Signed-off-by: Ed Cashin <ecashin@coraid.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Users with several network interfaces dedicated to AoE generally do not
configure them to support different-sized AoE data payloads on purpose.
For a given AoE target, there will be a set of local network interfaces
that can reach it. Using only the payload that will fit in the
smallest-sized MTU of all those local interfaces greatly simplifies the
driver, especially in failure scenarios.
Signed-off-by: Ed Cashin <ecashin@coraid.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The dev_queue_xmit function needs to have interrupts enabled, so the most
simple way to get the locking right but still fulfill that requirement is
to use a process that can call dev_queue_xmit serially over queued
transmissions.
Signed-off-by: Ed Cashin <ecashin@coraid.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
To allow users to choose an elevator algorithm for their particular
workloads, change from a make_request-style driver to an
I/O-request-queue-handler-style driver.
We have to do a couple of things that might be surprising. We manipulate
the page _count directly on the assumption that we still have no guarantee
that users of the block layer are prohibited from submitting bios
containing pages with zero reference counts.[1] If such a prohibition now
exists, I can get rid of the _count manipulation.
Just as before this patch, we still keep track of the sk_buffs that the
network layer still hasn't finished yet and cap the resources we use with
a "pool" of skbs.[2]
Now that the block layer maintains the disk stats, the aoe driver's
diskstats function can go away.
1. https://lkml.org/lkml/2007/3/1/374
2. https://lkml.org/lkml/2007/7/6/241
Signed-off-by: Ed Cashin <ecashin@coraid.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Make the frames the aoe driver uses to track the relationship between bios
and packets more flexible and detached, so that they can be passed to an
"aoe_ktio" thread for completion of I/O.
The frames are handled much like skbs, with a capped amount of
preallocation so that real-world use cases are likely to run smoothly and
degenerate gracefully even under memory pressure.
Decoupling I/O completion from the receive path and serializing it in a
process makes it easier to think about the correctness of the locking in
the driver, especially in the case of a remote MAC address becoming
unusable.
[dan.carpenter@oracle.com: cleanup an allocation a bit]
Signed-off-by: Ed Cashin <ecashin@coraid.com>
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
tAdd adds the ability to work with large packets composed of a number of
segments, using the scatter gather feature of the block layer (biovecs)
and the network layer (skb frag array). The motivation is the performance
gained by using a packet data payload greater than a page size and by
using the network card's scatter gather feature.
Users of the out-of-tree aoe driver already had these changes, but since
early 2011, they have complained of increased memory utilization and
higher CPU utilization during heavy writes.[1] The commit below appears
related, as it disables scatter gather on non-IP protocols inside the
harmonize_features function, even when the NIC supports sg.
commit f01a5236bd
Author: Jesse Gross <jesse@nicira.com>
Date: Sun Jan 9 06:23:31 2011 +0000
net offloading: Generalize netif_get_vlan_features().
With that regression in place, transmits always linearize sg AoE packets,
but in-kernel users did not have this patch. Before 2.6.38, though, these
changes were working to allow sg to increase performance.
1. http://www.spinics.net/lists/linux-mm/msg15184.html
Signed-off-by: Ed Cashin <ecashin@coraid.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In order for the network layer to see that AoE requires
no checksumming in a generic way, the packets must be
marked as requiring no checksum, so we make this requirement
explicit with the assertion.
Signed-off-by: Ed Cashin <ecashin@coraid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
dev_base_lock is the legacy way to lock the device list, and is planned
to disappear. (writers hold RTNL, readers hold RCU lock)
Convert aoecmd_cfg_pkts() to RCU locking.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Cc: "Ed L. Cashin" <ecashin@coraid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
percpu.h is included by sched.h and module.h and thus ends up being
included when building most .c files. percpu.h includes slab.h which
in turn includes gfp.h making everything defined by the two files
universally available and complicating inclusion dependencies.
percpu.h -> slab.h dependency is about to be removed. Prepare for
this change by updating users of gfp and slab facilities include those
headers directly instead of assuming availability. As this conversion
needs to touch large number of source files, the following script is
used as the basis of conversion.
http://userweb.kernel.org/~tj/misc/slabh-sweep.py
The script does the followings.
* Scan files for gfp and slab usages and update includes such that
only the necessary includes are there. ie. if only gfp is used,
gfp.h, if slab is used, slab.h.
* When the script inserts a new include, it looks at the include
blocks and try to put the new include such that its order conforms
to its surrounding. It's put in the include block which contains
core kernel includes, in the same order that the rest are ordered -
alphabetical, Christmas tree, rev-Xmas-tree or at the end if there
doesn't seem to be any matching order.
* If the script can't find a place to put a new include (mostly
because the file doesn't have fitting include block), it prints out
an error message indicating which .h file needs to be added to the
file.
The conversion was done in the following steps.
1. The initial automatic conversion of all .c files updated slightly
over 4000 files, deleting around 700 includes and adding ~480 gfp.h
and ~3000 slab.h inclusions. The script emitted errors for ~400
files.
2. Each error was manually checked. Some didn't need the inclusion,
some needed manual addition while adding it to implementation .h or
embedding .c file was more appropriate for others. This step added
inclusions to around 150 files.
3. The script was run again and the output was compared to the edits
from #2 to make sure no file was left behind.
4. Several build tests were done and a couple of problems were fixed.
e.g. lib/decompress_*.c used malloc/free() wrappers around slab
APIs requiring slab.h to be added manually.
5. The script was run on all .h files but without automatically
editing them as sprinkling gfp.h and slab.h inclusions around .h
files could easily lead to inclusion dependency hell. Most gfp.h
inclusion directives were ignored as stuff from gfp.h was usually
wildly available and often used in preprocessor macros. Each
slab.h inclusion directive was examined and added manually as
necessary.
6. percpu.h was updated not to include slab.h.
7. Build test were done on the following configurations and failures
were fixed. CONFIG_GCOV_KERNEL was turned off for all tests (as my
distributed build env didn't work with gcov compiles) and a few
more options had to be turned off depending on archs to make things
build (like ipr on powerpc/64 which failed due to missing writeq).
* x86 and x86_64 UP and SMP allmodconfig and a custom test config.
* powerpc and powerpc64 SMP allmodconfig
* sparc and sparc64 SMP allmodconfig
* ia64 SMP allmodconfig
* s390 SMP allmodconfig
* alpha SMP allmodconfig
* um on x86_64 SMP allmodconfig
8. percpu.h modifications were reverted so that it could be applied as
a separate patch and serve as bisection point.
Given the fact that I had only a couple of failures from tests on step
6, I'm fairly confident about the coverage of this conversion patch.
If there is a breakage, it's likely to be something in one of the arch
headers which should be easily discoverable easily on most builds of
the specific arch.
Signed-off-by: Tejun Heo <tj@kernel.org>
Guess-its-ok-by: Christoph Lameter <cl@linux-foundation.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>
Prevent the AoE block driver from creating cache aliases of page cache
pages on machines with virtually indexed caches.
Building kernels on an AT91SAM9G20 board without this patch fails with
segmentation faults after a couple of passes.
Signed-off-by: Peter Horton <zero@colonel-panic.org>
Cc: "Ed L. Cashin" <ecashin@coraid.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* Use ATA_CMD_* defines instead of WIN_* ones.
* Include <linux/ata.h> directly instead of through <linux/hdreg.h>.
Cc: Ed L. Cashin <ecashin@coraid.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Add %pm to omit the colons when printing a mac address.
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next-2.6: (1075 commits)
myri10ge: update driver version number to 1.4.3-1.369
r8169: add shutdown handler
r8169: preliminary 8168d support
r8169: support additional 8168cp chipset
r8169: change default behavior for mildly identified 8168c chipsets
r8169: add a new 8168cp flavor
r8169: add a new 8168c flavor (bis)
r8169: add a new 8168c flavor
r8169: sync existing 8168 device hardware start sequences with vendor driver
r8169: 8168b Tx performance tweak
r8169: make room for more specific 8168 hardware start procedure
r8169: shuffle some registers handling around (8168 operation only)
r8169: new phy init parameters for the 8168b
r8169: update phy init parameters
r8169: wake up the PHY of the 8168
af_key: fix SADB_X_SPDDELETE response
ath9k: Fix return code when ath9k_hw_setpower() fails on reset
ath9k: remove nasty FAIL macro from ath9k_hw_reset()
gre: minor cleanups in netlink interface
gre: fix copy and paste error
...
Move stats related fields - stamp, in_flight, dkstats - from disk to
part0 and unify stat handling such that...
* part_stat_*() now updates part0 together if the specified partition
is not part0. ie. part_stat_*() are now essentially all_stat_*().
* {disk|all}_stat_*() are gone.
* part_round_stats() is updated similary. It handles part0 stats
automatically and disk_round_stats() is killed.
* part_{inc|dec}_in_fligh() is implemented which automatically updates
part0 stats for parts other than part0.
* disk_map_sector_rcu() is updated to return part0 if no part matches.
Combined with the above changes, this makes NULL special case
handling in callers unnecessary.
* Separate stats show code paths for disk are collapsed into part
stats show code paths.
* Rename disk_stat_lock/unlock() to part_stat_lock/unlock()
While at it, reposition stat handling macros a bit and add missing
parentheses around macro parameters.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Move disk->capacity to part0->nr_sects and convert all users who
directly accessed the field to use {get|set}_capacity(). This is done
early to allow the __dev field to be moved.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
There are two variants of stat functions - ones prefixed with double
underbars which don't care about preemption and ones without which
disable preemption before manipulating per-cpu counters. It's unclear
whether the underbarred ones assume that preemtion is disabled on
entry as some callers don't do that.
This patch unifies diskstats access by implementing disk_stat_lock()
and disk_stat_unlock() which take care of both RCU (for partition
access) and preemption (for per-cpu counter access). diskstats access
should always be enclosed between the two functions. As such, there's
no need for the versions which disables preemption. They're removed
and double underbars ones are renamed to drop the underbars. As an
extra argument is added, there's no danger of using the old version
unconverted.
disk_stat_lock() uses get_cpu() and returns the cpu index and all
diskstat functions which access per-cpu counters now has @cpu
argument to help RT.
This change adds RCU or preemption operations at some places but also
collapses several preemption ops into one at others. Overall, the
performance difference should be negligible as all involved ops are
very lightweight per-cpu ones.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
disk->part[] is protected by its matching bdev's lock. However,
non-critical accesses like collecting stats and printing out sysfs and
proc information used to be performed without any locking. As
partitions can come and go dynamically, partitions can go away
underneath those non-critical accesses. As some of those accesses are
writes, this theoretically can lead to silent corruption.
This patch fixes the race by using RCU for the partition array and dev
reference counter to hold partitions.
* Rename disk->part[] to disk->__part[] to make sure no one outside
genhd layer proper accesses it directly.
* Use RCU for disk->__part[] dereferencing.
* Implement disk_{get|put}_part() which can be used to get and put
partitions from gendisk respectively.
* Iterators are implemented to help iterate through all partitions
safely.
* Functions which require RCU readlock are marked with _rcu suffix.
* Use disk_put_part() in __blkdev_put() instead of directly putting
the contained kobject.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
This patch makes the following misc updates in preparation for
disk->part dereference fix and extended block devt support.
* implment part_to_disk()
* fix comment about gendisk->part indexing
* rename get_part() to disk_map_sector()
* don't use n which is always zero while printing disk information in
diskstats_show()
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
get_part() is fairly expensive, as it O(N) loops over partitions
to find the right one. In lots of normal IO paths we end up looking
up the partition twice, to make matters even worse. Change the
stat add code to accept a passed in partition instead.
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Cc: Ed L. Cashin <ecashin@coraid.com>
Cc: Jens Axboe <jens.axboe@oracle.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Update the year in the copyright notices.
Signed-off-by: Ed L. Cashin <ecashin@coraid.com>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Ed Cashin
Eric Dumazet
Tejun Heo
Andrew Morton
Peter Horton
David S. Miller
Bartlomiej Zolnierkiewicz
Harvey Harrison
Linus Torvalds
Jens Axboe
Linus Torvalds