Most of the dentry members from structure caam_drv_private
are never used at all, so it is safe to remove them.
Since debugfs_remove_recursive() is called, we don't need the
file entries.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Acked-by: Horia Geantă <horia.geanta@nxp.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Add support for using the caam/jr backend on DPAA2-based SoCs.
These have some particularities we have to account for:
-HW S/G format is different
-Management Complex (MC) firmware initializes / manages (partially)
the CAAM block: MCFGR, QI enablement in QICTL, RNG
Signed-off-by: Horia Geantă <horia.geanta@nxp.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
RNG instantiation was previously fixed by
commit 62743a4145 ("crypto: caam - fix RNG init descriptor ret. code checking")
while deinstantiation was not addressed.
Since the descriptors used are similar, in the sense that they both end
with a JUMP HALT command, checking for errors should be similar too,
i.e. status code 7000_0000h should be considered successful.
Cc: <stable@vger.kernel.org> # 3.13+
Fixes: 1005bccd7a ("crypto: caam - enable instantiation of all RNG4 state handles")
Signed-off-by: Horia Geantă <horia.geanta@nxp.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The way Job Ring platform devices are created and released does not
allow for multiple create-release cycles.
JR0 Platform device creation error
JR0 Platform device creation error
caam 2100000.caam: no queues configured, terminating
caam: probe of 2100000.caam failed with error -12
The reason is that platform devices are created for each job ring:
for_each_available_child_of_node(nprop, np)
if (of_device_is_compatible(np, "fsl,sec-v4.0-job-ring") ||
of_device_is_compatible(np, "fsl,sec4.0-job-ring")) {
ctrlpriv->jrpdev[ring] =
of_platform_device_create(np, NULL, dev);
which sets OF_POPULATED on the device node, but then it cleans these up:
/* Remove platform devices for JobRs */
for (ring = 0; ring < ctrlpriv->total_jobrs; ring++) {
if (ctrlpriv->jrpdev[ring])
of_device_unregister(ctrlpriv->jrpdev[ring]);
}
which leaves OF_POPULATED set.
Use of_platform_populate / of_platform_depopulate instead.
This allows for a bit of driver clean-up, jrpdev is no longer needed.
Logic changes a bit too:
-exit in case of_platform_populate fails, since currently even QI backend
depends on JR; true, we no longer support the case when "some" of the JR
DT nodes are incorrect
-when cleaning up, caam_remove() would also depopulate RTIC in case
it would have been populated somewhere else - not the case for now
Cc: <stable@vger.kernel.org>
Fixes: 313ea293e9 ("crypto: caam - Add Platform driver for Job Ring")
Reported-by: Russell King <rmk+kernel@armlinux.org.uk>
Suggested-by: Rob Herring <robh+dt@kernel.org>
Signed-off-by: Horia Geantă <horia.geanta@nxp.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
CAAM engine supports two interfaces for crypto job submission:
-job ring interface - already existing caam/jr driver
-Queue Interface (QI) - caam/qi driver added in current patch
QI is present in CAAM engines found on DPAA platforms.
QI gets its I/O (frame descriptors) from QMan (Queue Manager) queues.
This patch adds a platform device for accessing CAAM's queue interface.
The requests are submitted to CAAM using one frame queue per
cryptographic context. Each crypto context has one shared descriptor.
This shared descriptor is attached to frame queue associated with
corresponding driver context using context_a.
The driver hides the mechanics of FQ creation, initialisation from its
applications. Each cryptographic context needs to be associated with
driver context which houses the FQ to be used to transport the job to
CAAM. The driver provides API for:
(a) Context creation
(b) Job submission
(c) Context deletion
(d) Congestion indication - whether path to/from CAAM is congested
The driver supports affining its context to a particular CPU.
This means that any responses from CAAM for the context in question
would arrive at the given CPU. This helps in implementing one CPU
per packet round trip in IPsec application.
The driver processes CAAM responses under NAPI contexts.
NAPI contexts are instantiated only on cores with affined portals since
only cores having their own portal can receive responses from DQRR.
The responses from CAAM for all cryptographic contexts ride on a fixed
set of FQs. We use one response FQ per portal owning core. The response
FQ is configured in each core's and thus portal's dedicated channel.
This gives the flexibility to direct CAAM's responses for a crypto
context on a given core.
Signed-off-by: Vakul Garg <vakul.garg@nxp.com>
Signed-off-by: Alex Porosanu <alexandru.porosanu@nxp.com>
Signed-off-by: Horia Geantă <horia.geanta@nxp.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Fix typos and add the following to the scripts/spelling.txt:
deintializing||deinitializing
deintialize||deinitialize
deintialized||deinitialized
Link: http://lkml.kernel.org/r/1481573103-11329-28-git-send-email-yamada.masahiro@socionext.com
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
If one of the JRs failed at init, the next JR used
the failed JR's IO space. The patch fixes this bug.
Signed-off-by: Tudor Ambarus <tudor-dan.ambarus@nxp.com>
Signed-off-by: Horia Geantă <horia.geanta@nxp.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Setting the dma mask could fail, thus make sure it succeeds
before going further.
Signed-off-by: Horia Geantă <horia.geanta@nxp.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
intern.h, jr.h are not needed in error.c
error.h is not needed in ctrl.c
Signed-off-by: Horia Geantă <horia.geanta@nxp.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Pull crypto updates from Herbert Xu:
"Here is the crypto update for 4.10:
API:
- add skcipher walk interface
- add asynchronous compression (acomp) interface
- fix algif_aed AIO handling of zero buffer
Algorithms:
- fix unaligned access in poly1305
- fix DRBG output to large buffers
Drivers:
- add support for iMX6UL to caam
- fix givenc descriptors (used by IPsec) in caam
- accelerated SHA256/SHA512 for ARM64 from OpenSSL
- add SSE CRCT10DIF and CRC32 to ARM/ARM64
- add AEAD support to Chelsio chcr
- add Armada 8K support to omap-rng"
* 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6: (148 commits)
crypto: testmgr - fix overlap in chunked tests again
crypto: arm/crc32 - accelerated support based on x86 SSE implementation
crypto: arm64/crc32 - accelerated support based on x86 SSE implementation
crypto: arm/crct10dif - port x86 SSE implementation to ARM
crypto: arm64/crct10dif - port x86 SSE implementation to arm64
crypto: testmgr - add/enhance test cases for CRC-T10DIF
crypto: testmgr - avoid overlap in chunked tests
crypto: chcr - checking for IS_ERR() instead of NULL
crypto: caam - check caam_emi_slow instead of re-lookup platform
crypto: algif_aead - fix AIO handling of zero buffer
crypto: aes-ce - Make aes_simd_algs static
crypto: algif_skcipher - set error code when kcalloc fails
crypto: caam - make aamalg_desc a proper module
crypto: caam - pass key buffers with typesafe pointers
crypto: arm64/aes-ce-ccm - Fix AEAD decryption length
MAINTAINERS: add crypto headers to crypto entry
crypt: doc - remove misleading mention of async API
crypto: doc - fix header file name
crypto: api - fix comment typo
crypto: skcipher - Add separate walker for AEAD decryption
..
Start with a clean slate before dealing with bit 16 (pointer size)
of Master Configuration Register.
This fixes the case of AArch64 boot loader + AArch32 kernel, when
the boot loader might set MCFGR[PS] and kernel would fail to clear it.
Cc: <stable@vger.kernel.org>
Reported-by: Alison Wang <alison.wang@nxp.com>
Signed-off-by: Horia Geantă <horia.geanta@nxp.com>
Reviewed-By: Alison Wang <Alison.wang@nxp.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
i.MX6UL does only require three clocks to enable CAAM module.
Signed-off-by: Marcus Folkesson <marcus.folkesson@gmail.com>
Acked-by: Rob Herring <robh@kernel.org>
Reviewed-by: Horia Geantă <horia.geanta@nxp.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
We get 1 warning when biuld kernel with W=1:
drivers/crypto/caam/ctrl.c:398:5: warning: no previous prototype for 'caam_get_era' [-Wmissing-prototypes]
In fact, this function is declared in drivers/crypto/caam/ctrl.h,
so this patch add missing header dependencies.
Signed-off-by: Baoyou Xie <baoyou.xie@linaro.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
There are SoCs like LS1043A where CAAM endianness (BE) does not match
the default endianness of the core (LE).
Moreover, there are requirements for the driver to handle cases like
CPU_BIG_ENDIAN=y on ARM-based SoCs.
This requires for a complete rewrite of the I/O accessors.
PPC-specific accessors - {in,out}_{le,be}XX - are replaced with
generic ones - io{read,write}[be]XX.
Endianness is detected dynamically (at runtime) to allow for
multiplatform kernels, for e.g. running the same kernel image
on LS1043A (BE CAAM) and LS2080A (LE CAAM) armv8-based SoCs.
While here: debugfs entries need to take into consideration the
endianness of the core when displaying data. Add the necessary
glue code so the entries remain the same, but they are properly
read, regardless of the core and/or SEC endianness.
Note: pdb.h fixes only what is currently being used (IPsec).
Reviewed-by: Tudor Ambarus <tudor-dan.ambarus@nxp.com>
Signed-off-by: Horia Geantă <horia.geanta@nxp.com>
Signed-off-by: Alex Porosanu <alexandru.porosanu@nxp.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Most users of IS_ERR_VALUE() in the kernel are wrong, as they
pass an 'int' into a function that takes an 'unsigned long'
argument. This happens to work because the type is sign-extended
on 64-bit architectures before it gets converted into an
unsigned type.
However, anything that passes an 'unsigned short' or 'unsigned int'
argument into IS_ERR_VALUE() is guaranteed to be broken, as are
8-bit integers and types that are wider than 'unsigned long'.
Andrzej Hajda has already fixed a lot of the worst abusers that
were causing actual bugs, but it would be nice to prevent any
users that are not passing 'unsigned long' arguments.
This patch changes all users of IS_ERR_VALUE() that I could find
on 32-bit ARM randconfig builds and x86 allmodconfig. For the
moment, this doesn't change the definition of IS_ERR_VALUE()
because there are probably still architecture specific users
elsewhere.
Almost all the warnings I got are for files that are better off
using 'if (err)' or 'if (err < 0)'.
The only legitimate user I could find that we get a warning for
is the (32-bit only) freescale fman driver, so I did not remove
the IS_ERR_VALUE() there but changed the type to 'unsigned long'.
For 9pfs, I just worked around one user whose calling conventions
are so obscure that I did not dare change the behavior.
I was using this definition for testing:
#define IS_ERR_VALUE(x) ((unsigned long*)NULL == (typeof (x)*)NULL && \
unlikely((unsigned long long)(x) >= (unsigned long long)(typeof(x))-MAX_ERRNO))
which ends up making all 16-bit or wider types work correctly with
the most plausible interpretation of what IS_ERR_VALUE() was supposed
to return according to its users, but also causes a compile-time
warning for any users that do not pass an 'unsigned long' argument.
I suggested this approach earlier this year, but back then we ended
up deciding to just fix the users that are obviously broken. After
the initial warning that caused me to get involved in the discussion
(fs/gfs2/dir.c) showed up again in the mainline kernel, Linus
asked me to send the whole thing again.
[ Updated the 9p parts as per Al Viro - Linus ]
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Andrzej Hajda <a.hajda@samsung.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Link: https://lkml.org/lkml/2016/1/7/363
Link: https://lkml.org/lkml/2016/5/27/486
Acked-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org> # For nvmem part
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Increasing CAAM DMA engine transaction size either
-reduces the number of required transactions or
-adds the ability to transfer more data with same transaction count
Signed-off-by: Horia Geant? <horia.geanta@nxp.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Previous change (see "Fixes" tag) to the MCFGR register
clears AWCACHE[0] ("bufferable" AXI3 attribute) (which is "1" at POR).
This makes all writes non-bufferable, causing a ~ 5% performance drop
for PPC-based platforms.
Rework previous change such that MCFGR[AWCACHE]=4'b0011
(bufferable + cacheable) for all platforms.
Note: For ARM-based platforms, AWCACHE[0] is ignored
by the interconnect IP.
Cc: <stable@vger.kernel.org> # 4.3+
Fixes: f109674951 ("crypto: caam - fix snooping for write transactions")
Signed-off-by: Horia Geant? <horia.geanta@nxp.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
"The preferred form for passing a size of a struct is the following:
p = kmalloc(sizeof(*p), ...);
....
The preferred form for allocating a zeroed array is the following:
p = kcalloc(n, sizeof(...), ...); "
,so do as suggested.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Reviewed-by: Horia Geant? <horia.geanta@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Instead of propagating a 'fake' error code, just propagate the real
one in the case of caam_drv_identify_clk() failure.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Reviewed-by: Horia Geant? <horia.geanta@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
In the error path we should disable the resources that were previously
acquired, so fix the error handling accordingly.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Reviewed-by: Horia Geant? <horia.geanta@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Most significant part of JQCR (Job Queue Control Register) contains
bits that control endianness: ILE - Immediate Little Endian,
DWS - Double Word Swap.
The bits are automatically set by the Job Queue Controller HW.
Unfortunately these bits are cleared in SW when submitting descriptors
via the register-based service interface.
>From LS1021A:
JQCR_MS = 08080100 - before writing: ILE | DWS | SRC (JR0)
JQCR_MS = 30000100 - after writing: WHL | FOUR | SRC (JR0)
This would cause problems on little endian caam for descriptors
containing immediata data or double-word pointers.
Currently there is no problem since the only descriptors ran through
this interface are the ones that (un)instantiate RNG.
Signed-off-by: Horia Geant? <horia.geanta@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
LS1021A is a QorIQ SoC having little endian CAAM.
There are a few differences b/w QorIQ and i.MX from CAAM perspective:
1. i.MX platforms are somewhat special wrt. 64-bit registers:
-big endian format at 64-bit level: MSW at address+0 and LSW at address+4
-little endian format at 32-bit level (within MSW and LSW)
and thus need special handling.
2. No CCM (clock controller module) for QorIQ.
No CAAM clocks to enable / disable.
A new Kconfig option - CRYPTO_DEV_FSL_CAAM_LE - is added to indicate
CAAM is little endian (*). It is hidden from the user (to avoid
misconfiguration); when adding support for a new platform with LE CAAM,
either the Kconfig needs to be updated or the corresponding defconfig
needs to indicate that CAAM is LE.
(*) Using a DT property to provide CAAM endianness would not allow
for the ifdeffery.
In order to keep changes to a minimum, the following changes
are postponed:
-endianness fix of the last word in the S/G (rsvd2, bpid, offset),
fields are always 0 anyway;
-S/G format fix for i.MX7 (yes, i.MX7 support was not added yet,
but still...)
Signed-off-by: Horia Geant? <horia.geanta@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Variable 'ret' is only used for returning the value 0.
We can make it simpler and just return 0 instead.
The semantic patch that makes this change is available
in scripts/coccinelle/misc/returnvar.cocci.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
ARM-based systems may disable clocking to the CAAM device on the
Freescale i.MX platform for power management purposes. This patch
enables the required clocks when the CAAM module is initialized and
disables the required clocks when the CAAM module is shut down.
Signed-off-by: Victoria Milhoan <vicki.milhoan@freescale.com>
Tested-by: Horia Geantă <horia.geanta@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Add set/clear 32-bit primitives for compatibility with ARM devices since
the primitives were previously only defined for the Power architecture.
Signed-off-by: Victoria Milhoan <vicki.milhoan@freescale.com>
Tested-by: Horia Geantă <horia.geanta@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
When successful, the descriptor that performs RNG initialization
is allowed to return a status code of 7000_0000h, since last command
in the descriptor is a JUMP HALT.
Signed-off-by: Horia Geant? <horia.geanta@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
HW coherency won't work properly for CAAM write transactions
if AWCACHE is left to default (POR) value - 4'b0001.
It has to be programmed to 4'b0010, i.e. AXI3 Cacheable bit set.
For platforms that have HW coherency support:
-PPC-based: the update has no effect; CAAM coherency already works
due to the IOMMU (PAMU) driver setting the correct memory coherency
attributes
-ARM-based: the update fixes cache coherency issues,
since IOMMU (SMMU) driver is not programmed to behave similar to PAMU
Signed-off-by: Horia Geant? <horia.geanta@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
In order to ensure that the ERA property is properly read from DT
on all platforms, of_property_read* function needs to be used.
Signed-off-by: Alex Porosanu <alexandru.porosanu@freescale.com>
Signed-off-by: Horia Geant? <horia.geanta@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Fix a "Trying to vfree() nonexistent vm area" error when unloading the CAAM
controller module by providing the correct pointer value to iounmap().
Signed-off-by: Victoria Milhoan <vicki.milhoan@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
CAAM's memory is broken into following address blocks:
Block Included Registers
0 General Registers
1-4 Job ring registers
6 RTIC registers
7 QI registers
8 DECO and CCB
Size of the above stated blocks varies in various platforms. The block size can be 4K or 64K.
The block size can be dynamically determined by reading CTPR register in CAAM.
This patch initializes the block addresses dynamically based on the value read from this register.
Signed-off-by: Ruchika Gupta <r66431@freescale.com>
Signed-off-by: Nitesh Narayan Lal <b44382@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The sampling of the oscillator can be done in multiple modes for
generating the entropy value. By default, this is set to von
Neumann. This patch changes the sampling to raw data, since it
has been discovered that the generated entropy has a better
'quality'.
Signed-off-by: Alex Porosanu <alexandru.porosanu@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The entropy delay (the length in system clocks of each
entropy sample) for the RNG4 block of CAAM is dependent
on the frequency of the SoC. By elaborate methods, it
has been determined that a good starting value for all
platforms integrating the CAAM IP is 3200. Using a
higher value has additional benefit of speeding up
the process of instantiating the RNG, since the entropy
delay will be increased and instantiation of the RNG
state handles will be reattempted by the driver. If the
starting value is low, for certain platforms, this can
lead to a quite lengthy process.
This patch changes the starting value of the length of
the entropy sample to 3200 system clocks.
In addition to this change, the attempted entropy delay
values are now printed on the console upon initialization
of the RNG block.
While here, a safeguard for yielding the processor was
added for ensuring that in very adverse cases,
the CPU isn't hogged by the instantiation loop.
Signed-off-by: Alex Porosanu <alexandru.porosanu@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The rtfrqmax & rtfrqmin set the bounds of the expected frequency of the
oscillator, when SEC runs at its maximum frequency. For certain platforms
(f.i. T2080), the oscillator is very fast and thus if the SEC runs at
a lower than normal frequency, the ring oscillator is incorrectly detected
as being out of bounds.
This patch effectively disables the maximum frequency check, by setting a
high enough maximum allowable frequency for the oscillator. The reasoning
behind this is that usually a broken oscillator will run too slow
(i.e. not run at all) rather than run too fast.
Signed-off-by: Alex Porosanu <alexandru.porosanu@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
RSR (Request Source Register) is not used when
virtualization is disabled, thus don't poll for Valid bit.
Besides this, if used, timeout has to be reinitialized.
Signed-off-by: Horia Geanta <horia.geanta@freescale.com>
Acked-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Replace dma_set_mask with dma_set_mask_and_coherent, since both
streaming and coherent DMA mappings are being used.
Signed-off-by: Horia Geanta <horia.geanta@freescale.com>
Acked-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
In the current setup debug file system enables us to debug the operational
details for only one CAAM. This patch adds the support for debugging multiple
CAAM's.
Signed-off-by: Nitesh Narayan Lal <b44382@freescale.com>
Signed-off-by: Vakul Garg <b16394@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
For platforms with virtualization enabled
1. The job ring registers can be written to only is the job ring has been
started i.e STARTR bit in JRSTART register is 1
2. For DECO's under direct software control, with virtualization enabled
PL, BMT, ICID and SDID values need to be provided. These are provided by
selecting a Job ring in start mode whose parameters would be used for the
DECO access programming.
Signed-off-by: Ruchika Gupta <ruchika.gupta@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Some registers like SECVID, CHAVID, CHA Revision Number,
CTPR were defined as 64 bit resgisters. The IP provides
a DWT bit(Double word Transpose) to transpose the two words when
a double word register is accessed. However setting this bit
would also affect the operation of job descriptors as well as
other registers which are truly double word in nature.
So, for the IP to work correctly on big-endian as well as
little-endian SoC's, change is required to access all 32 bit
registers as 32 bit quantities.
Signed-off-by: Ruchika Gupta <ruchika.gupta@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
This patch moves data allocated using kzalloc to managed data allocated
using devm_kzalloc and cleans now unnecessary kfrees in probe and remove
functions. Also, linux/device.h is added to make sure the devm_*()
routine declarations are unambiguously available. Earlier, in the probe
function ctrlpriv was leaked on the failure of ctrl = of_iomap(nprop, 0);
as well as on the failure of ctrlpriv->jrpdev = kzalloc(...); . These
two bugs have been fixed by the patch.
The following Coccinelle semantic patch was used for making the change:
identifier p, probefn, removefn;
@@
struct platform_driver p = {
.probe = probefn,
.remove = removefn,
};
@prb@
identifier platform.probefn, pdev;
expression e, e1, e2;
@@
probefn(struct platform_device *pdev, ...) {
<+...
- e = kzalloc(e1, e2)
+ e = devm_kzalloc(&pdev->dev, e1, e2)
...
?-kfree(e);
...+>
}
@rem depends on prb@
identifier platform.removefn;
expression e;
@@
removefn(...) {
<...
- kfree(e);
...>
}
Signed-off-by: Himangi Saraogi <himangi774@gmail.com>
Acked-by: Julia Lawall <julia.lawall@lip6.fr>
Reviewed-by: Marek Vasut <marex@denx.de>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
SEC ERA has to be retrieved by reading the "fsl,sec-era" property
from the device tree. This property is updated/filled in by
u-boot.
Signed-off-by: Alex Porosanu <alexandru.porosanu@freescale.com>
Reviewed-by: Horia Geanta <horia.geanta@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The SEC Controller driver creates platform devices for it's child job ring nodes.
Currently the driver uses for_each_compatible routine which traverses
the whole device tree to create the job rings for the platform device.
The patch changes this to search for the compatible property of job ring
only in the child nodes i.e., the job rings are created as per the number
of children associated with the crypto node.
Signed-off-by: Nitesh Lal <NiteshNarayanLal@freescale.com>
Reviewed-by: Horia Geanta <horia.geanta@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Pull crypto update from Herbert Xu:
- Made x86 ablk_helper generic for ARM
- Phase out chainiv in favour of eseqiv (affects IPsec)
- Fixed aes-cbc IV corruption on s390
- Added constant-time crypto_memneq which replaces memcmp
- Fixed aes-ctr in omap-aes
- Added OMAP3 ROM RNG support
- Add PRNG support for MSM SoC's
- Add and use Job Ring API in caam
- Misc fixes
[ NOTE! This pull request was sent within the merge window, but Herbert
has some questionable email sending setup that makes him public enemy
#1 as far as gmail is concerned. So most of his emails seem to be
trapped by gmail as spam, resulting in me not seeing them. - Linus ]
* git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6: (49 commits)
crypto: s390 - Fix aes-cbc IV corruption
crypto: omap-aes - Fix CTR mode counter length
crypto: omap-sham - Add missing modalias
padata: make the sequence counter an atomic_t
crypto: caam - Modify the interface layers to use JR API's
crypto: caam - Add API's to allocate/free Job Rings
crypto: caam - Add Platform driver for Job Ring
hwrng: msm - Add PRNG support for MSM SoC's
ARM: DT: msm: Add Qualcomm's PRNG driver binding document
crypto: skcipher - Use eseqiv even on UP machines
crypto: talitos - Simplify key parsing
crypto: picoxcell - Simplify and harden key parsing
crypto: ixp4xx - Simplify and harden key parsing
crypto: authencesn - Simplify key parsing
crypto: authenc - Export key parsing helper function
crypto: mv_cesa: remove deprecated IRQF_DISABLED
hwrng: OMAP3 ROM Random Number Generator support
crypto: sha256_ssse3 - also test for BMI2
crypto: mv_cesa - Remove redundant of_match_ptr
crypto: sahara - Remove redundant of_match_ptr
...
Fabio Estevam
Horia Geantă
Tudor Ambarus
Herbert Xu
Masahiro Yamada
Linus Torvalds
Marcus Folkesson
Baoyou Xie
Russell King
Arnd Bergmann
Fabio Estevam
Horia Geant?
Victoria Milhoan
Alex Porosanu
Cristian Stoica
Wolfram Sang
Nitesh Narayan Lal
Ruchika Gupta
Himangi Saraogi
Nitesh Lal
Rob Herring