Some controllers fail to send confirmation GPE after address write.
Detect this and don't expect such confirmation in future.
This is a generalization of previous workaround
(66c5f4e736), which did only read address.
http://bugzilla.kernel.org/show_bug.cgi?id=9327
Signed-off-by: Alexey Starikovskiy <astarikovskiy@suse.de>
Tested-by: Romano Giannetti <romano.giannetti@gmail.com>
Signed-off-by: Len Brown <len.brown@intel.com>
drivers/acpi/sbs.c: In function acpi_battery_add:
drivers/acpi/sbs.c:811: warning: ignoring return value of device_create_file,
declared with attribute warn_unused_result
Additional cleanups:
* use struct acpi_battery in acpi_battery_remove() to clean up function
calls, just like acpi_battery_add() already does.
* put braces around unregister call, as it depends on dev being not NULL.
* remove unneeded braces
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Signed-off-by: Alexey Starikovskiy <astarikovskiy@suse.de>
Signed-off-by: Len Brown <len.brown@intel.com>
Add throttling control via MSR when T-states uses
the FixHW Control Status registers.
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Signed-off-by: Li Shaohua <shaohua.li@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Previously _PDC was evaluated later, and thus we'd not get
the chance to tell the BIOS that we can suport FixedHW registers (MSRs)
and the BIOS would always ask us to use System I/O access
for throttling.
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Signed-off-by: Li Shaohua <shaohua.li@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
_TSS was erroneously ignored, in favor of the FADT.
When TSS is used, the access width is included in the PTC control/status
register. So it is unnecessary that the access bit width is multiplied by 8.
At the same time the bit_offset should be considered for system I/O Access.
It should be checked the bit_width and bit_offset of PTC regsiter in order to
avoid the failure of system I/O access. It means that bit_width plus
bit_offset can't be greater than 32.
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Signed-off-by: Li Shaohua <shaohua.li@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Change the function interface for throttling control via PTC.
The following functions are concerned:
acpi_read_throttling_status()
acpi_write_throttling_state()
acpi_get_throttling_value()
acpi_get_throttling_state()
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Signed-off-by: Li Shaohua <shaohua.li@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Factor out legacy FADT.duty_width code
and run it only in the non _TSS case.
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Signed-off-by: Li Shaohua <shaohua.li@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
We've run into BIOS that hand us 4-bit access width requests
for T-state control when the code expected only multipls of 8-bits.
Round up.
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Signed-off-by: Li Shaohua <shaohua.li@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
When a T-state limit change notification is received,
Linux must evaluate _TPC and change its current
T-state immediately to comply with the new limit.
Previously, Linux would notice the new limit
only upon the next throttling change.
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Signed-off-by: Li Shaohua <shaohua.li@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Check if AC state has changed across resume and notify userspace if so.
Fixes "[2.6.24-rc1 regression] AC adapter state does not change after resume"
Signed-off-by: Alexey Starikovskiy <astarikovskiy@suse.de>
Tested-by: Andrey Borzenkov <arvidjaar@mail.ru>
Cc: Len Brown <lenb@kernel.org>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Do not provide /proc/acpi/ac_adapter if ACPI_PROCFS is not defined. This
eliminates duplicated power adapters in HAL and makes it consistent with
battery module
Signed-off-by: Andrey Borzenkov <arvidjaar@mail.ru>
Acked-by: Alexey Starikovskiy <astarikovskiy@suse.de>
Cc: Len Brown <lenb@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Zillions of people are getting my-battery-monitor-doesnt-work problems
(including me).
Lessen the damage by making ACPI_PROCFS default to on.
Cc: Len Brown <lenb@kernel.org>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Acked-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
list_for_each_safe() only protects list from list alterations
performed by the same thread. One still needs to implement
proper locking when list is being accessed from several threads.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Acked-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
If input_register_device() fails input_free_device() must
be called to release memory allocated for the device.
Also consolidate error handling in acpi_bus_video_add()
and handle input_allocate_device() failures.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Acked-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Properly set up parent on input device registered by the video driver.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Acked-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
get_property() should not call battery_update(), it also should call
get_status() only if battery is present to avoid cycle and oops.
Signed-off-by: Alexey Starikovskiy <astarikovskiy@suse.de>
Tested-by: Rolf Eike Beer <eike-kernel@sf-tec.de>
Acked-by: Johannes Weiner <hannes@saeurebad.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add documentation in Kconfig help about the move of /proc/acpi/battery
to /sys/class/power_supply when selecting ACPI_PROCFS. This will impact
a lot of users and should be documented.
Signed-off-by: Jerome Pinot <ngc891@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
If a battery is at a critical charge level and not being charged or
discharged, then the ACPI _BST method will return a state of 4, and
the current acpi_battery_get_property() code will not set any property
value for POWER_SUPPLY_PROP_STATUS. This will cause an oops in
power_supply_show_property() when it reads off the end of the
status_text array. This actually was causing a 100% reproducible
crash on boot on my laptop with two batteries, when one battery was
completely drained and the laptop was not plugged in.
Fix this by making sure acpi_battery_get_property() returns
POWER_SUPPLY_STATUS_UNKNOWN for any battery state it doesn't already
handle explicitly. There doesn't seem to be any status enum value
defined that makes more sense than 'unknown' for a battery at a
critical charge level.
Signed-off-by: Roland Dreier <roland@digitalvampire.org>
Acked-by: Alexey Starikovskiy <astarikovskiy@suse.de>
Signed-off-by: Len Brown <lenb@t61.(none)>
Current description for CONFIG_ACPI includes the word "Support" twice. One
effect of this is that in menuconfig the "--->" that indicates the presence
of sub-options will not show up unless you have a very wide console.
Signed-off-by: Frans Pop <elendil@planet.nl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Len Brown <len.brown@intel.com>
POWER_SUPPLY is needed for AC, battery, and SBS sysfs support. Use
'select' instead of 'depends on', as it is will not be selected by anything
else, leading to confusion.
Signed-off-by: Alexey Starikovskiy <astarikovskiy@suse.de>
Tested-by: Frans Pop <elendil@planet.nl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Len Brown <len.brown@intel.com>
Some machines return integer instead of expected string.
Signed-off-by: Alexey Starikovskiy <astarikovskiy@suse.de>
Tested-by: Andrey Borzenkov <arvidjaar@mail.ru>
Tested-by: Frans Pop <elendil@planet.nl>
Signed-off-by: Len Brown <len.brown@intel.com>
Support Li-Ion as possible name for technology.
Signed-off-by: Alexey Starikovskiy <astarikovskiy@suse.de>
Signed-off-by: Len Brown <len.brown@intel.com>
Make sure no power_supply object is present unless we actualy detect
presence of battery. This fixes ghost batteries detected by HAL
Signed-off-by: Andrey Borzenkov <arvidjaar@mail.ru>
Signed-off-by: Alexey Starikovskiy <astarikovskiy@suse.de>
Signed-off-by: Len Brown <len.brown@intel.com>
This fixes some totally illogical and wrong code that converts things to
and from BCD mode essentially randomly, does math on values in BCD mode
etc etc. Introduce a few helper functions to make it a bit more obvious
what is going on, and make sure that we always do all the arithmetic
(and anythign else, for that matter) in binary, not BCD.
Tested by Mark Lord, who found the problem originally, and also pushed
the patch back and reminded me about it.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch fixes a use-after-free introduced by
commit 30c08574da
(ACPI: EC: Add new query handler to list head)
Spotted by the Coverity checker.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Acked-by: Alexey Starikovskiy <astarikovskiy@suse.de>
Signed-off-by: Len Brown <len.brown@intel.com>
After commit f1d4661abe this was dead
code.
Spotted by the Coverity checker.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Acked-by: Alexey Starikovskiy <astarikovskiy@suse.de>
Signed-off-by: Len Brown <len.brown@intel.com>
force_power_state was used as a workaround for invalid cached
power state of the device. We do not cache power state, so no need for
workaround.
Signed-off-by: Alexey Starikovskiy <astarikovskiy@suse.de>
Acked-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Len Brown <len.brown@intel.com>
ACPI may change power resource state behind our back, so don't
keep our local copy, which may not be valid.
Signed-off-by: Alexey Starikovskiy <astarikovskiy@suse.de>
Signed-off-by: Len Brown <len.brown@intel.com>
Insert printk() for every change in operational mode.
Signed-off-by: Alexey Starikovskiy <astarikovskiy@suse.de>
Acked-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Len Brown <len.brown@intel.com>
Some controllers do not send interrupts for OBF=1 event, but send
them for IBF=0. Add workaround for them.
Reference: http://bugzilla.kernel.org/show_bug.cgi?id=8459
Signed-off-by: Alexey Starikovskiy <astarikovskiy@suse.de>
Signed-off-by: Len Brown <len.brown@intel.com>
With the auto selection of operation mode, absence of GPEs does not
really degrade performance, so let PM code to handle
enabling/disabling GPEs.
This is a revert of 5d57a6a55e,
which was meant to be temporary.
Reference: http://bugzilla.kernel.org/show_bug.cgi?id=7977
Signed-off-by: Alexey Starikovskiy <astarikovskiy@suse.de>
Acked-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Len Brown <len.brown@intel.com>
Start in POLL mode, and if we receive confirmation GPE,
switch to INT mode.
If confirmations are not sent, switch back to POLL.
Signed-off-by: Alexey Starikovskiy <astarikovskiy@suse.de>
Signed-off-by: Len Brown <len.brown@intel.com>
There is no interrupt after last read according to spec, so
don't set bit that we are expecting one.
Signed-off-by: Alexey Starikovskiy <astarikovskiy@suse.de>
Signed-off-by: Len Brown <len.brown@intel.com>
Number of flags is about to be increased, so it is better to
put them all into bits.
No functional changes.
Signed-off-by: Alexey Starikovskiy <astarikovskiy@suse.de>
Acked-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Len Brown <len.brown@intel.com>
Input layer should know about initial state of lid switch,
even before first notify.
Reference: https://bugzilla.novell.com/show_bug.cgi?id=326814
Signed-off-by: Alexey Starikovskiy <astarikovskiy@suse.de>
Acked-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Len Brown <len.brown@intel.com>
acpi_leave_sleep_state() should have correct list of wake and
runtime GPEs, which is available only after disable_wakeup_device()
is called.
Signed-off-by: Alexey Starikovskiy <astarikovskiy@suse.de>
Acked-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Len Brown <len.brown@intel.com>
Commit 9b03933080 removed
acpi_gpe_sleep_prepare(), the only function used at S5 transition
Add call to generic acpi_enable_wake_device().
Reference: https://bugzilla.novell.com/show_bug.cgi?id=299882
Signed-off-by: Alexey Starikovskiy <astarikovskiy@suse.de>
Acked-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Len Brown <len.brown@intel.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/bunk/trivial: (74 commits)
fix do_sys_open() prototype
sysfs: trivial: fix sysfs_create_file kerneldoc spelling mistake
Documentation: Fix typo in SubmitChecklist.
Typo: depricated -> deprecated
Add missing profile=kvm option to Documentation/kernel-parameters.txt
fix typo about TBI in e1000 comment
proc.txt: Add /proc/stat field
small documentation fixes
Fix compiler warning in smount example program from sharedsubtree.txt
docs/sysfs: add missing word to sysfs attribute explanation
documentation/ext3: grammar fixes
Documentation/java.txt: typo and grammar fixes
Documentation/filesystems/vfs.txt: typo fix
include/asm-*/system.h: remove unused set_rmb(), set_wmb() macros
trivial copy_data_pages() tidy up
Fix typo in arch/x86/kernel/tsc_32.c
file link fix for Pegasus USB net driver help
remove unused return within void return function
Typo fixes retrun -> return
x86 hpet.h: remove broken links
...
* ssh://master.kernel.org/pub/scm/linux/kernel/git/tglx/linux-2.6-x86: (33 commits)
x86: convert cpuinfo_x86 array to a per_cpu array
x86: introduce frame_pointer() and stack_pointer()
x86 & generic: change to __builtin_prefetch()
i386: do not BUG_ON() when MSR is unknown
x86: acpi use cpu_physical_id
x86: convert cpu_llc_id to be a per cpu variable
x86: convert cpu_to_apicid to be a per cpu variable
i386: introduce "used_vectors" bitmap which can be used to reserve vectors.
x86: use raw locks during oopses
x86: honor _PAGE_PSE bit on page walks
i386: do cpuid_device_create() in CPU_UP_PREPARE instead of CPU_ONLINE.
x86: implement missing x86_64 function smp_call_function_mask()
x86: use descriptor's functions instead of inline assembly
i386: consolidate show_regs and show_registers for i386
i386: make callgraph use dump_trace() on i386/x86_64
x86: enable iommu_merge by default
i386: i386 add AMD64 Barcelona PMU MSR definitions to msr.h
x86: Unify i386 and x86-64 early quirks
x86: enable HPET on ICH3 and ICH4
x86: force enable HPET on VT8235/8237 chipsets
...
Manually fix trivial conflict with task pid container helper changes in
arch/x86/kernel/process_32.c
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6: (41 commits)
ACPICA: hw: Don't carry spinlock over suspend
ACPICA: hw: remove use_lock flag from acpi_hw_register_{read, write}
ACPI: cpuidle: port idle timer suspend/resume workaround to cpuidle
ACPI: clean up acpi_enter_sleep_state_prep
Hibernation: Make sure that ACPI is enabled in acpi_hibernation_finish
ACPI: suppress uninitialized var warning
cpuidle: consolidate 2.6.22 cpuidle branch into one patch
ACPI: thinkpad-acpi: skip blanks before the data when parsing sysfs
ACPI: AC: Add sysfs interface
ACPI: SBS: Add sysfs alarm
ACPI: SBS: Add ACPI_PROCFS around procfs handling code.
ACPI: SBS: Add support for power_supply class (and sysfs)
ACPI: SBS: Make SBS reads table-driven.
ACPI: SBS: Simplify data structures in SBS
ACPI: SBS: Split host controller (ACPI0001) from SBS driver (ACPI0002)
ACPI: EC: Add new query handler to list head.
ACPI: Add acpi_bus_generate_event4() function
ACPI: Battery: add sysfs alarm
ACPI: Battery: Add sysfs support
ACPI: Battery: Misc clean-ups, no functional changes
...
Fix up conflicts in drivers/misc/thinkpad_acpi.[ch] manually
get rid of input BIT* duplicate defines
use newly global defined macros for input layer. Also remove includes of
input.h from non-input sources only for BIT macro definiton. Define the
macro temporarily in local manner, all those local definitons will be
removed further in this patchset (to not break bisecting).
BIT macro will be globally defined (1<<x)
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Cc: <dtor@mail.ru>
Acked-by: Jiri Kosina <jkosina@suse.cz>
Cc: <lenb@kernel.org>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Cc: <perex@suse.cz>
Acked-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Cc: <vernux@us.ibm.com>
Cc: <malattia@linux.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This is from an earlier message from Christoph Lameter:
processor_core.c currently tries to determine the apicid by special casing
for IA64 and x86. The desired information is readily available via
cpu_physical_id()
on IA64, i386 and x86_64.
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Additionally, boot_cpu_id needed to be exported to fix compile errors in
dma code when !CONFIG_SMP.
Signed-off-by: Mike Travis <travis@sgi.com>
Cc: Andi Kleen <ak@suse.de>
Cc: Christoph Lameter <clameter@sgi.com>
Cc: "Siddha, Suresh B" <suresh.b.siddha@intel.com>
Cc: Len Brown <lenb@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
The following scenario leads to total confusion of the platform firmware on
some boxes (eg. HPC nx6325):
* Hibernate with ACPI enabled
* Resume passing "acpi=off" to the boot kernel
To prevent this from happening it's necessary to check if ACPI is enabled (and
enable it if that's not the case) _right_ _after_ control has been transfered
from the boot kernel to the image kernel, before device_power_up() is called
(ie. with interrupts disabled). Enabling ACPI after calling
device_power_up() turns out to be insufficient.
For this reason, introduce new hibernation callback ->leave() that will be
executed before device_power_up() by the restored image kernel. To make it
work, it also is necessary to move swsusp_suspend() from swsusp.c to disk.c
(it's name is changed to "create_image", which is more up to the point).
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Rename 'struct hibernation_ops' to 'struct platform_hibernation_ops' in
analogy with 'struct platform_suspend_ops'.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Pavel Machek <pavel@ucw.cz>
Cc: Len Brown <lenb@kernel.org>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
During hibernation we also need to tell the ACPI core that we're going to put
the system into the S4 sleep state. For this reason, an additional method in
'struct hibernation_ops' is needed, playing the role of set_target() in
'struct platform_suspend_operations'. Moreover, the role of the .prepare()
method is now different, so it's better to introduce another method, that in
general may be different from .prepare(), that will be used to prepare the
platform for creating the hibernation image (.prepare() is used anyway to
notify the platform that we're going to enter the low power state after the
image has been saved).
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
There is no reason why the .prepare() and .finish() methods in 'struct
platform_suspend_ops' should take any arguments, since architectures don't use
these methods' argument in any practically meaningful way (ie. either the
target system sleep state is conveyed to the platform by .set_target(), or
there is only one suspend state supported and it is indicated to the PM core
by .valid(), or .prepare() and .finish() aren't defined at all). There also
is no reason why .finish() should return any result.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Pavel Machek <pavel@ucw.cz>
Cc: Len Brown <lenb@kernel.org>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The name of 'struct pm_ops' suggests that it is related to the power
management in general, but in fact it is only related to suspend. Moreover,
its name should indicate what this structure is used for, so it seems
reasonable to change it to 'struct platform_suspend_ops'. In that case, the
name of the global variable of this type used by the PM core and the names of
related functions should be changed accordingly.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Pavel Machek <pavel@ucw.cz>
Cc: Len Brown <lenb@kernel.org>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* master.kernel.org:/pub/scm/linux/kernel/git/gregkh/driver-2.6: (75 commits)
PM: merge device power-management source files
sysfs: add copyrights
kobject: update the copyrights
kset: add some kerneldoc to help describe what these strange things are
Driver core: rename ktype_edd and ktype_efivar
Driver core: rename ktype_driver
Driver core: rename ktype_device
Driver core: rename ktype_class
driver core: remove subsystem_init()
sysfs: move sysfs file poll implementation to sysfs_open_dirent
sysfs: implement sysfs_open_dirent
sysfs: move sysfs_dirent->s_children into sysfs_dirent->s_dir
sysfs: make sysfs_root a regular directory dirent
sysfs: open code sysfs_attach_dentry()
sysfs: make s_elem an anonymous union
sysfs: make bin attr open get active reference of parent too
sysfs: kill unnecessary NULL pointer check in sysfs_release()
sysfs: kill unnecessary sysfs_get() in open paths
sysfs: reposition sysfs_dirent->s_mode.
sysfs: kill sysfs_update_file()
...
Convert from class_device to device for drivers/video.
Signed-off-by: Tony Jones <tonyj@suse.de>
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
A number of different drivers incorrect access the kobject name field
directly. This is not correct as the name might not be in the array.
Use the proper accessor function instead.
This changes the uevent buffer functions to use a struct instead of a
long list of parameters. It does no longer require the caller to do the
proper buffer termination and size accounting, which is currently wrong
in some places. It fixes a known bug where parts of the uevent
environment are overwritten because of wrong index calculations.
Many thanks to Mathieu Desnoyers for finding bugs and improving the
error handling.
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Cc: Mathieu Desnoyers <mathieu.desnoyers@polymtl.ca>
Cc: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The conversion of x86-64 to clock events makes the
#ifdef CONFIG_GENERIC_CLOCKEVENTS
n the timer broadcast functions useless. Remove it.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: john stultz <johnstul@us.ibm.com>
Cc: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/bart/ide-2.6: (24 commits)
ide: use only ->set_pio_mode method for programming PIO modes (take 2)
sis5513: don't change UDMA settings when programming PIO
it8213/piix/slc90e66: don't change DMA settings when programming PIO
alim15x3: PIO mode setup fixes
siimage: fix ->set_pio_mode method to select PIO data transfer
cs5520: don't enable VDMA in ->speedproc
sc1200: remove redundant warning message from sc1200_tune_chipset()
ide-pmac: PIO mode setup fixes (take 3)
icside: fix ->speedproc to return on unsupported modes (take 5)
sgiioc4: use ide_tune_dma()
amd74xx/via82cxxx: use ide_tune_dma()
ide: add ide_set{_max}_pio() (take 4)
ide: Kconfig face-lift
ide: move ide_rate_filter() calls to the upper layer (take 2)
sis5513: add ->udma_filter method for chipset_family >= ATA_133
ide: mode limiting fixes for user requested speed changes
ide: add missing ide_rate_filter() calls to ->speedproc()-s
ide: call udma_filter() before resorting to the UltraDMA mask
ide: make jmicron match vendor and device class
pdc202xx_new: switch to using pci_get_slot() (take 2)
...
ACPI spec defines the sequence of IDE power on/off:
Powering down:
Call _GTM.
Power down drive (calls _PS3 method and turns off power planes).
Powering up:
Power up drive (calls _PS0 method if present and turns on power planes).
Call _STM passing info from _GTM (possibly modified), with ID data from
each drive.
Initialize the channel.
May modify the results of _GTF.
For each drive:
Call _GTF.
Execute task file (possibly modified).
This patch adds the missed _PS0/_PS3 methods call.
Signed-off-by: Shaohua Li <shaohua.li@intel.com>
Acked-by: Len Brown <len.brown@intel.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
ACPI uses acpi_get_register() in order to get into suspend.
This function is guarded by acpi_gbl_hardware_lock, which will be carried
into resume phase.
At resume interrupts are enabled and first ACPI interrupt deadlocks on this
lock.
Solution seems to be to not lock register read, as there are no concurrent
activity at this point.
Reference: http://bugzilla.kernel.org/show_bug.cgi?id=7499
Signed-off-by: Alexey Starikovskiy <astarikovskiy@suse.de>
Signed-off-by: Len Brown <len.brown@intel.com>
use_lock flag is used once for acpi_hw_register_read, and never for
acpi_hw_register_write. It will greatly simplify understanding of
locking if we just drop this use_lock altogether, and wrap the only call
to ..._read in lock/unlock.
Signed-off-by: Alexey Starikovskiy <astarikovskiy@suse.de>
Signed-off-by: Len Brown <len.brown@intel.com>
Some timers stop during C2 and C3, and so there are various
generations of timer broadcast workarounds to deal with that.
But that (already complex) code gets confused during suspend.
As it is unlikely that deep C-states would save much power
during the actual suspend/resume process anyway, deep C-states
were disabled via the addition of .suspend/.resume hooks
in to the ACPI processor driver.
Here that workaround is ported to the cpuidle version of
the ACPI idle loop. Technically, ACPI could un-register
itself from cpuidle on .suspend, but that code path
is currently quite cumbersome. So instead,
we simply invoke C1 from the C2 and C3 handlers
for the duration of .suspend/.resume.
Signed-off-by: Len Brown <len.brown@intel.com>
Remove some redundant code from acpi_enter_sleep_state_prep() and clean up
a comment in there.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Len Brown <len.brown@intel.com>
If the BIOS does not enable ACPI and the "acpi=off" command line parameter
is passed to the boot kernel, ACPI may be disabled when the (restored)
image kernel attempts to execute acpi_hibernation_finish(). To prevent
this from happening we can call acpi_enable() from
acpi_hibernation_finish() (if ACPI is already enabled, this will have no
effect).
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Len Brown <len.brown@intel.com>
drivers/acpi/tables/tbutils.c: In function `acpi_tb_parse_root_table':
drivers/acpi/tables/tbutils.c:403: warning: `rsdt_address' may be used uninitialized in this function
Reported-by: Uwe Bugla <uwe.bugla@gmx.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Len Brown <len.brown@intel.com>
commit e5a16b1f9eec0af7cfa0830304b41c1c0833cf9f
Author: Len Brown <len.brown@intel.com>
Date: Tue Oct 2 23:44:44 2007 -0400
cpuidle: shrink diff
processor_idle.c | 440 +++++++++++++++++++++++++++++++++++++++++--
1 file changed, 429 insertions(+), 11 deletions(-)
Signed-off-by: Len Brown <len.brown@intel.com>
commit dfbb9d5aedfb18848a3e0d6f6e3e4969febb209c
Author: Len Brown <len.brown@intel.com>
Date: Wed Sep 26 02:17:55 2007 -0400
cpuidle: reduce diff size
Reduces the cpuidle processor_idle.c diff vs 2.6.22 from this
processor_idle.c | 2006 ++++++++++++++++++++++++++-----------------
1 file changed, 1219 insertions(+), 787 deletions(-)
to this:
processor_idle.c | 502 +++++++++++++++++++++++++++++++++++++++----
1 file changed, 458 insertions(+), 44 deletions(-)
...for the purpose of making the cpuilde patch less invasive
and easier to review.
no functional changes. build tested only.
Signed-off-by: Len Brown <len.brown@intel.com>
commit 889172fc915f5a7fe20f35b133cbd205ce69bf6c
Author: Venki Pallipadi <venkatesh.pallipadi@intel.com>
Date: Thu Sep 13 13:40:05 2007 -0700
cpuidle: Retain old ACPI policy for !CONFIG_CPU_IDLE
Retain the old policy in processor_idle, so that when CPU_IDLE is not
configured, old C-state policy will still be used. This provides a
clean gradual migration path from old ACPI policy to new cpuidle
based policy.
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
commit 9544a8181edc7ecc33b3bfd69271571f98ed08bc
Author: Venki Pallipadi <venkatesh.pallipadi@intel.com>
Date: Thu Sep 13 13:39:17 2007 -0700
cpuidle: Configure governors by default
Quoting Len "Do not give an option to users to shoot themselves in the foot".
Remove the configurability of ladder and menu governors as they are
needed for default policy of cpuidle. That way users will not be able to
have cpuidle without any policy loosing all C-state power savings.
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
commit 8975059a2c1e56cfe83d1bcf031bcf4cb39be743
Author: Adam Belay <abelay@novell.com>
Date: Tue Aug 21 18:27:07 2007 -0400
CPUIDLE: load ACPI properly when CPUIDLE is disabled
Change the registration return codes for when CPUIDLE
support is not compiled into the kernel. As a result, the ACPI
processor driver will load properly even if CPUIDLE is unavailable.
However, it may be possible to cleanup the ACPI processor driver further
and eliminate some dead code paths.
Signed-off-by: Adam Belay <abelay@novell.com>
Acked-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
commit e0322e2b58dd1b12ec669bf84693efe0dc2414a8
Author: Adam Belay <abelay@novell.com>
Date: Tue Aug 21 18:26:06 2007 -0400
CPUIDLE: remove cpuidle_get_bm_activity()
Remove cpuidle_get_bm_activity() and updates governors
accordingly.
Signed-off-by: Adam Belay <abelay@novell.com>
Acked-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
commit 18a6e770d5c82ba26653e53d240caa617e09e9ab
Author: Adam Belay <abelay@novell.com>
Date: Tue Aug 21 18:25:58 2007 -0400
CPUIDLE: max_cstate fix
Currently max_cstate is limited to 0, resulting in no idle processor
power management on ACPI platforms. This patch restores the value to
the array size.
Signed-off-by: Adam Belay <abelay@novell.com>
Acked-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
commit 1fdc0887286179b40ce24bcdbde663172e205ef0
Author: Adam Belay <abelay@novell.com>
Date: Tue Aug 21 18:25:40 2007 -0400
CPUIDLE: handle BM detection inside the ACPI Processor driver
Update the ACPI processor driver to detect BM activity and
limit state entry depth internally, rather than exposing such
requirements to CPUIDLE. As a result, CPUIDLE can drop this
ACPI-specific interface and become more platform independent. BM
activity is now handled much more aggressively than it was in the
original implementation, so some testing coverage may be needed to
verify that this doesn't introduce any DMA buffer under-run issues.
Signed-off-by: Adam Belay <abelay@novell.com>
Acked-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
commit 0ef38840db666f48e3cdd2b769da676c57228dd9
Author: Adam Belay <abelay@novell.com>
Date: Tue Aug 21 18:25:14 2007 -0400
CPUIDLE: menu governor updates
Tweak the menu governor to more effectively handle non-timer
break events. Non-timer break events are detected by comparing the
actual sleep time to the expected sleep time. In future revisions, it
may be more reliable to use the timer data structures directly.
Signed-off-by: Adam Belay <abelay@novell.com>
Acked-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
commit bb4d74fca63fa96cf3ace644b15ae0f12b7df5a1
Author: Adam Belay <abelay@novell.com>
Date: Tue Aug 21 18:24:40 2007 -0400
CPUIDLE: fix 'current_governor' sysfs entry
Allow the "current_governor" sysfs entry to properly handle
input terminated with '\n'.
Signed-off-by: Adam Belay <abelay@novell.com>
Acked-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
commit df3c71559bb69b125f1a48971bf0d17f78bbdf47
Author: Len Brown <len.brown@intel.com>
Date: Sun Aug 12 02:00:45 2007 -0400
cpuidle: fix IA64 build (again)
Signed-off-by: Len Brown <len.brown@intel.com>
commit a02064579e3f9530fd31baae16b1fc46b5a7bca8
Author: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Date: Sun Aug 12 01:39:27 2007 -0400
cpuidle: Remove support for runtime changing of max_cstate
Remove support for runtime changeability of max_cstate. Drivers can use
use latency APIs.
max_cstate can still be used as a boot time option and dmi override.
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
commit 0912a44b13adf22f5e3f607d263aed23b4910d7e
Author: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Date: Sun Aug 12 01:39:16 2007 -0400
cpuidle: Remove ACPI cstate_limit calls from ipw2100
ipw2100 already has code to use accetable_latency interfaces to limit the
C-state. Remove the calls to acpi_set_cstate_limit and acpi_get_cstate_limit
as they are redundant.
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
commit c649a76e76be6bff1fd770d0a775798813a3f6e0
Author: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Date: Sun Aug 12 01:35:39 2007 -0400
cpuidle: compile fix for pause and resume functions
Fix the compilation failure when cpuidle is not compiled in.
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Acked-by: Adam Belay <adam.belay@novell.com>
Signed-off-by: Len Brown <len.brown@intel.com>
commit 2305a5920fb8ee6ccec1c62ade05aa8351091d71
Author: Adam Belay <abelay@novell.com>
Date: Thu Jul 19 00:49:00 2007 -0400
cpuidle: re-write
Some portions have been rewritten to make the code cleaner and lighter
weight. The following is a list of changes:
1.) the state name is now included in the sysfs interface
2.) detection, hotplug, and available state modifications are handled by
CPUIDLE drivers directly
3.) the CPUIDLE idle handler is only ever installed when at least one
cpuidle_device is enabled and ready
4.) the menu governor BM code no longer overflows
5.) the sysfs attributes are now printed as unsigned integers, avoiding
negative values
6.) a variety of other small cleanups
Also, Idle drivers are no longer swappable during runtime through the
CPUIDLE sysfs inteface. On i386 and x86_64 most idle handlers (e.g.
poll, mwait, halt, etc.) don't benefit from an infrastructure that
supports multiple states, so I think using a more general case idle
handler selection mechanism would be cleaner.
Signed-off-by: Adam Belay <abelay@novell.com>
Acked-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Acked-by: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
commit df25b6b56955714e6e24b574d88d1fd11f0c3ee5
Author: Len Brown <len.brown@intel.com>
Date: Tue Jul 24 17:08:21 2007 -0400
cpuidle: fix IA64 buid
Signed-off-by: Len Brown <len.brown@intel.com>
commit fd6ada4c14488755ff7068860078c437431fbccd
Author: Adrian Bunk <bunk@stusta.de>
Date: Mon Jul 9 11:33:13 2007 -0700
cpuidle: static
make cpuidle_replace_governor() static
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Cc: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Len Brown <len.brown@intel.com>
commit c1d4a2cebcadf2429c0c72e1d29aa2a9684c32e0
Author: Adrian Bunk <bunk@stusta.de>
Date: Tue Jul 3 00:54:40 2007 -0400
cpuidle: static
This patch makes the needlessly global struct menu_governor static.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Len Brown <len.brown@intel.com>
commit dbf8780c6e8d572c2c273da97ed1cca7608fd999
Author: Andrew Morton <akpm@linux-foundation.org>
Date: Tue Jul 3 00:49:14 2007 -0400
export symbol tick_nohz_get_sleep_length
ERROR: "tick_nohz_get_sleep_length" [drivers/cpuidle/governors/menu.ko] undefined!
ERROR: "tick_nohz_get_idle_jiffies" [drivers/cpuidle/governors/menu.ko] undefined!
And please be sure to get your changes to core kernel suitably reviewed.
Cc: Adam Belay <abelay@novell.com>
Cc: Venki Pallipadi <venkatesh.pallipadi@intel.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: john stultz <johnstul@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Len Brown <len.brown@intel.com>
commit 29f0e248e7017be15f99febf9143a2cef00b2961
Author: Andrew Morton <akpm@linux-foundation.org>
Date: Tue Jul 3 00:43:04 2007 -0400
tick.h needs hrtimer.h
It uses hrtimers.
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Len Brown <len.brown@intel.com>
commit e40cede7d63a029e92712a3fe02faee60cc38fb4
Author: Venki Pallipadi <venkatesh.pallipadi@intel.com>
Date: Tue Jul 3 00:40:34 2007 -0400
cpuidle: first round of documentation updates
Documentation changes based on Pavel's feedback.
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Len Brown <len.brown@intel.com>
commit 83b42be2efece386976507555c29e7773a0dfcd1
Author: Venki Pallipadi <venkatesh.pallipadi@intel.com>
Date: Tue Jul 3 00:39:25 2007 -0400
cpuidle: add rating to the governors and pick the one with highest rating by default
Introduce a governor rating scheme to pick the right governor by default.
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Len Brown <len.brown@intel.com>
commit d2a74b8c5e8f22def4709330d4bfc4a29209b71c
Author: Venki Pallipadi <venkatesh.pallipadi@intel.com>
Date: Tue Jul 3 00:38:08 2007 -0400
cpuidle: make cpuidle sysfs driver governor switch off by default
Make default cpuidle sysfs to show current_governor and current_driver in
read-only mode. More elaborate available_governors and available_drivers with
writeable current_governor and current_driver interface only appear with
"cpuidle_sysfs_switch" boot parameter.
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Len Brown <len.brown@intel.com>
commit 1f60a0e80bf83cf6b55c8845bbe5596ed8f6307b
Author: Venki Pallipadi <venkatesh.pallipadi@intel.com>
Date: Tue Jul 3 00:37:00 2007 -0400
cpuidle: menu governor: change the early break condition
Change the C-state early break out algorithm in menu governor.
We only look at early breakouts that result in wakeups shorter than idle
state's target_residency. If such a breakout is frequent enough, eliminate
the particular idle state upto a timeout period.
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Len Brown <len.brown@intel.com>
commit 45a42095cf64b003b4a69be3ce7f434f97d7af51
Author: Venki Pallipadi <venkatesh.pallipadi@intel.com>
Date: Tue Jul 3 00:35:38 2007 -0400
cpuidle: fix uninitialized variable in sysfs routine
Fix the uninitialized usage of ret.
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Len Brown <len.brown@intel.com>
commit 80dca7cdba3e6ee13eae277660873ab9584eb3be
Author: Venki Pallipadi <venkatesh.pallipadi@intel.com>
Date: Tue Jul 3 00:34:16 2007 -0400
cpuidle: reenable /proc/acpi//power interface for the time being
Keep /proc/acpi/processor/CPU*/power around for a while as powertop depends
on it. It will be marked deprecated and removed in future. powertop can use
cpuidle interfaces instead.
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Len Brown <len.brown@intel.com>
commit 589c37c2646c5e3813a51255a5ee1159cb4c33fc
Author: Venki Pallipadi <venkatesh.pallipadi@intel.com>
Date: Tue Jul 3 00:32:37 2007 -0400
cpuidle: menu governor and hrtimer compile fix
Compile fix for menu governor.
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Len Brown <len.brown@intel.com>
commit 0ba80bd9ab3ed304cb4f19b722e4cc6740588b5e
Author: Len Brown <len.brown@intel.com>
Date: Thu May 31 22:51:43 2007 -0400
cpuidle: build fix - cpuidle vs ipw2100 module
ERROR: "acpi_set_cstate_limit" [drivers/net/wireless/ipw2100.ko] undefined!
Signed-off-by: Len Brown <len.brown@intel.com>
commit d7d8fa7f96a7f7682be7c6cc0cc53fa7a18c3b58
Author: Adam Belay <abelay@novell.com>
Date: Sat Mar 24 03:47:07 2007 -0400
cpuidle: add the 'menu' governor
Here is my first take at implementing an idle PM governor that takes
full advantage of NO_HZ. I call it the 'menu' governor because it
considers the full list of idle states before each entry.
I've kept the implementation fairly simple. It attempts to guess the
next residency time and then chooses a state that would meet at least
the break-even point between power savings and entry cost. To this end,
it selects the deepest idle state that satisfies the following
constraints:
1. If the idle time elapsed since bus master activity was detected
is below a threshold (currently 20 ms), then limit the selection
to C2-type or above.
2. Do not choose a state with a break-even residency that exceeds
the expected time remaining until the next timer interrupt.
3. Do not choose a state with a break-even residency that exceeds
the elapsed time between the last pair of break events,
excluding timer interrupts.
This governor has an advantage over "ladder" governor because it
proactively checks how much time remains until the next timer interrupt
using the tick infrastructure. Also, it handles device interrupt
activity more intelligently by not including timer interrupts in break
event calculations. Finally, it doesn't make policy decisions using the
number of state entries, which can have variable residency times (NO_HZ
makes these potentially very large), and instead only considers sleep
time deltas.
The menu governor can be selected during runtime using the cpuidle sysfs
interface like so:
"echo "menu" > /sys/devices/system/cpu/cpuidle/current_governor"
Signed-off-by: Adam Belay <abelay@novell.com>
Signed-off-by: Len Brown <len.brown@intel.com>
commit a4bec7e65aa3b7488b879d971651cc99a6c410fe
Author: Adam Belay <abelay@novell.com>
Date: Sat Mar 24 03:47:03 2007 -0400
cpuidle: export time until next timer interrupt using NO_HZ
Expose information about the time remaining until the next
timer interrupt expires by utilizing the dynticks infrastructure.
Also modify the main idle loop to allow dynticks to handle
non-interrupt break events (e.g. DMA). Finally, expose sleep ticks
information to external code. Thomas Gleixner is responsible for much
of the code in this patch. However, I've made some additional changes,
so I'm probably responsible if there are any bugs or oversights :)
Signed-off-by: Adam Belay <abelay@novell.com>
Signed-off-by: Len Brown <len.brown@intel.com>
commit 2929d8996fbc77f41a5ff86bb67cdde3ca7d2d72
Author: Adam Belay <abelay@novell.com>
Date: Sat Mar 24 03:46:58 2007 -0400
cpuidle: governor API changes
This patch prepares cpuidle for the menu governor. It adds an optional
stage after idle state entry to give the governor an opportunity to
check why the state was exited. Also it makes sure the idle loop
returns after each state entry, allowing the appropriate dynticks code
to run.
Signed-off-by: Adam Belay <abelay@novell.com>
Signed-off-by: Len Brown <len.brown@intel.com>
commit 3a7fd42f9825c3b03e364ca59baa751bb350775f
Author: Venki Pallipadi <venkatesh.pallipadi@intel.com>
Date: Thu Apr 26 00:03:59 2007 -0700
cpuidle: hang fix
Prevent hang on x86-64, when ACPI processor driver is added as a module on
a system that does not support C-states.
x86-64 expects all idle handlers to enable interrupts before returning from
idle handler. This is due to enter_idle(), exit_idle() races. Make
cpuidle_idle_call() confirm to this when there is no pm_idle_old.
Also, cpuidle look at the return values of attch_driver() and set
current_driver to NULL if attach fails on all CPUs.
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Len Brown <len.brown@intel.com>
commit 4893339a142afbd5b7c01ffadfd53d14746e858e
Author: Shaohua Li <shaohua.li@intel.com>
Date: Thu Apr 26 10:40:09 2007 +0800
cpuidle: add support for max_cstate limit
With CPUIDLE framework, the max_cstate (to limit max cpu c-state)
parameter is ingored. Some systems require it to ignore C2/C3
and some drivers like ipw require it too.
Signed-off-by: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
commit 43bbbbe1cb998cbd2df656f55bb3bfe30f30e7d1
Author: Shaohua Li <shaohua.li@intel.com>
Date: Thu Apr 26 10:40:13 2007 +0800
cpuidle: add cpuidle_fore_redetect_devices API
add cpuidle_force_redetect_devices API,
which forces all CPU redetect idle states.
Next patch will use it.
Signed-off-by: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
commit d1edadd608f24836def5ec483d2edccfb37b1d19
Author: Shaohua Li <shaohua.li@intel.com>
Date: Thu Apr 26 10:40:01 2007 +0800
cpuidle: fix sysfs related issue
Fix the cpuidle sysfs issue.
a. make kobject dynamicaly allocated
b. fixed sysfs init issue to avoid suspend/resume issue
Signed-off-by: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
commit 7169a5cc0d67b263978859672e86c13c23a5570d
Author: Randy Dunlap <randy.dunlap@oracle.com>
Date: Wed Mar 28 22:52:53 2007 -0400
cpuidle: 1-bit field must be unsigned
A 1-bit bitfield has no room for a sign bit.
drivers/cpuidle/governors/ladder.c:54:16: error: dubious bitfield without explicit `signed' or `unsigned'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Cc: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Len Brown <len.brown@intel.com>
commit 4658620158dc2fbd9e4bcb213c5b6fb5d05ba7d4
Author: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Date: Wed Mar 28 22:52:41 2007 -0400
cpuidle: fix boot hang
Patch for cpuidle boot hang reported by Larry Finger here.
http://www.ussg.iu.edu/hypermail/linux/kernel/0703.2/2025.html
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Cc: Larry Finger <larry.finger@lwfinger.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Len Brown <len.brown@intel.com>
commit c17e168aa6e5fe3851baaae8df2fbc1cf11443a9
Author: Len Brown <len.brown@intel.com>
Date: Wed Mar 7 04:37:53 2007 -0500
cpuidle: ladder does not depend on ACPI
build fix for CONFIG_ACPI=n
In file included from drivers/cpuidle/governors/ladder.c:21:
include/acpi/processor.h:88: error: expected specifier-qualifier-list before âacpi_integerâ
include/acpi/processor.h:106: error: expected specifier-qualifier-list before âacpi_integerâ
include/acpi/processor.h:168: error: expected specifier-qualifier-list before âacpi_handleâ
Signed-off-by: Len Brown <len.brown@intel.com>
commit 8c91d958246bde68db0c3f0c57b535962ce861cb
Author: Adrian Bunk <bunk@stusta.de>
Date: Tue Mar 6 02:29:40 2007 -0800
cpuidle: make code static
This patch makes the following needlessly global code static:
- driver.c: __cpuidle_find_driver()
- governor.c: __cpuidle_find_governor()
- ladder.c: struct ladder_governor
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Cc: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Cc: Adam Belay <abelay@novell.com>
Cc: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Len Brown <len.brown@intel.com>
commit 0c39dc3187094c72c33ab65a64d2017b21f372d2
Author: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Date: Wed Mar 7 02:38:22 2007 -0500
cpu_idle: fix build break
This patch fixes a build breakage with !CONFIG_HOTPLUG_CPU and
CONFIG_CPU_IDLE.
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Len Brown <len.brown@intel.com>
commit 8112e3b115659b07df340ef170515799c0105f82
Author: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Date: Tue Mar 6 02:29:39 2007 -0800
cpuidle: build fix for !CPU_IDLE
Fix the compile issues when CPU_IDLE is not configured.
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Cc: Adam Belay <abelay@novell.com>
Cc: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Len Brown <len.brown@intel.com>
commit 1eb4431e9599cd25e0d9872f3c2c8986821839dd
Author: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Date: Thu Feb 22 13:54:57 2007 -0800
cpuidle take2: Basic documentation for cpuidle
Documentation for cpuidle infrastructure
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Adam Belay <abelay@novell.com>
Signed-off-by: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
commit ef5f15a8b79123a047285ec2e3899108661df779
Author: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Date: Thu Feb 22 13:54:03 2007 -0800
cpuidle take2: Hookup ACPI C-states driver with cpuidle
Hookup ACPI C-states onto generic cpuidle infrastructure.
drivers/acpi/procesor_idle.c is now a ACPI C-states driver that registers as
a driver in cpuidle infrastructure and the policy part is removed from
drivers/acpi/processor_idle.c. We use governor in cpuidle instead.
Signed-off-by: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Adam Belay <abelay@novell.com>
Signed-off-by: Len Brown <len.brown@intel.com>
commit 987196fa82d4db52c407e8c9d5dec884ba602183
Author: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Date: Thu Feb 22 13:52:57 2007 -0800
cpuidle take2: Core cpuidle infrastructure
Announcing 'cpuidle', a new CPU power management infrastructure to manage
idle CPUs in a clean and efficient manner.
cpuidle separates out the drivers that can provide support for multiple types
of idle states and policy governors that decide on what idle state to use
at run time.
A cpuidle driver can support multiple idle states based on parameters like
varying power consumption, wakeup latency, etc (ACPI C-states for example).
A cpuidle governor can be usage model specific (laptop, server,
laptop on battery etc).
Main advantage of the infrastructure being, it allows independent development
of drivers and governors and allows for better CPU power management.
A huge thanks to Adam Belay and Shaohua Li who were part of this mini-project
since its beginning and are greatly responsible for this patchset.
This patch:
Core cpuidle infrastructure.
Introduces a new abstraction layer for cpuidle:
* which manages drivers that can support multiple idles states. Drivers
can be generic or particular to specific hardware/platform
* allows pluging in multiple policy governors that can take idle state policy
decision
* The core also has a set of sysfs interfaces with which administrato can know
about supported drivers and governors and switch them at run time.
Signed-off-by: Adam Belay <abelay@novell.com>
Signed-off-by: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Three main sets of changes:
1) dmi_get_system_info() return value should have been marked const,
since callers should not be changing that data.
2) const-ify DMI internals, since DMI firmware tables should,
whenever possible, be marked const to ensure we never ever write to
that data area.
3) const-ify DMI API, to enable marking tables const where possible
in low-level drivers.
And if we're really lucky, this might enable some additional
optimizations on the part of the compiler.
The bulk of the changes are #2 and #3, which are interrelated. #1 could
have been a separate patch, but it was so small compared to the others,
it was easier to roll it into this changeset.
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Refer to Documentation/power_supply_class.txt for interface description.
Signed-off-by: Alexey Starikovskiy <astarikovskiy@suse.de>
Signed-off-by: Len Brown <len.brown@intel.com>
Make procfs support optional under ACPI_PROCFS
Signed-off-by: Alexey Starikovskiy <astarikovskiy@suse.de>
Signed-off-by: Len Brown <len.brown@intel.com>
Add support for power_supply class and sysfs interface of it.
Refer to Documentation/power_supply_class.txt for interface description.
Signed-off-by: Alexey Starikovskiy <astarikovskiy@suse.de>
Signed-off-by: Len Brown <len.brown@intel.com>
Re-factor SBS functions to use tables and cycles for repeated operations.
Signed-off-by: Alexey Starikovskiy <astarikovskiy@suse.de>
Signed-off-by: Len Brown <len.brown@intel.com>
Replace poll-based host controller driver with the notify-based one.
Split it out of sbs.c.
Signed-off-by: Alexey Starikovskiy <astarikovskiy@suse.de>
Signed-off-by: Len Brown <len.brown@intel.com>
acpi_bus_generate_event() takes two strings out of passed device object.
SBS needs to supply these strings directly.
Signed-off-by: Alexey Starikovskiy <astarikovskiy@suse.de>
Signed-off-by: Len Brown <len.brown@intel.com>
Refer to Documentation/power_supply_class.txt for interface description.
Signed-off-by: Alexey Starikovskiy <astarikovskiy@suse.de>
Signed-off-by: Len Brown <len.brown@intel.com>
acpi_extract_package() creates more problems with memory management than
it solves as helper for package handling.
Signed-off-by: Alexey Starikovskiy <astarikovskiy@suse.de>
Signed-off-by: Len Brown <len.brown@intel.com>
S4 suspend to disk will disable GPE's permanently
because acpi_gpe_sleep_prepare() does not have
a counterpart at resume time. Thus, those devices
became unavailable for wakeup from subsequent
S3 suspend-to-ram.
Here acpi_gpe_sleep_prepare() is removed, and upon suspend
acpi_enable_wakeup_device() gets its functionality.
Upon resume, acpi_disable_wakeup_device() restores the state.
https://bugzilla.novell.com/show_bug.cgi?id=292300
Signed-off-by: Alexey Starikovskiy <astarikovskiy@suse.de>
Acked-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Len Brown <len.brown@intel.com>
This fixes compilation with CONFIG_SUSPEND unset and CONFIG_HIBERNATION set
(raf. http://marc.info/?l=linux-acpi&m=119055289723895&w=4).
Signed-off-by: Alexey Starikovskiy <astarikovskiy@suse.de>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Len Brown <len.brown@intel.com>
device_suspend() calls ACPI suspend functions, which seems to have undesired
side effects on lower idle C-states. It took me some time to realize that
especially the VAIO BIOSes (both Andrews jinxed UP and my elfstruck SMP one)
show this effect. I'm quite sure that other bug reports against suspend/resume
about turning the system into a brick have the same root cause.
After fishing in the dark for quite some time, I realized that removing the ACPI
processor module before suspend (this removes the lower C-state functionality)
made the problem disappear. Interestingly enough the propability of having a
bricked box is influenced by various factors (interrupts, size of the ram image,
...). Even adding a bunch of printks in the wrong places made the problem go
away. The previous periodic tick implementation simply pampered over the
problem, which explains why the dyntick / clockevents changes made this more
prominent.
We avoid complex functionality during the boot process and we have to do the
same during suspend/resume. It is a similar scenario and equaly fragile.
Add suspend / resume functions to the ACPI processor code and disable the lower
idle C-states across suspend/resume. Fall back to the default idle
implementation (halt) instead.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Andrew Morton <akpm@linux-foundation.org>
Cc: Len Brown <lenb@kernel.org>
Cc: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Cc: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Make the S0 state be always reported as supported
Signed-off: Frans Pop <elendil@planet.nl>
Acked-by: Alexey Starikovskiy <astarikovskiy@suse.de>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Len Brown <len.brown@intel.com>
Alexey Starikovskiy
Jeff Garzik
Zhao Yakui
Andrey Borzenkov
Andrew Morton
Len Brown
Dmitry Torokhov
Jerome Pinot
Roland Dreier
Frans Pop
Linus Torvalds
Adrian Bunk
Linus Torvalds
Rolf Eike Beer
Jiri Slaby
Mike Travis
Rafael J. Wysocki
Al Viro
tonyj@suse.de
Greg Kroah-Hartman
Kay Sievers
Thomas Gleixner
Shaohua Li
Jeff Garzik