Граф коммитов

348 Коммитов

Автор SHA1 Сообщение Дата
MyungJoo Ham 735a3d9efd regulator: Support MAX8998/LP3974 DVS-GPIO
The previous driver did not support BUCK1-DVS3, BUCK1-DVS4, and
BUCK2-DVS2 modes. This patch adds such modes and an option to block
setting buck1/2 voltages out of the preset values.

Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2011-01-14 12:38:16 +01:00
MyungJoo Ham 337ce5d1c5 mfd: Support LP3974 RTC
The first releases of LP3974 have a large delay in RTC registers,
which requires 2 seconds of delay after writing to a rtc register
(recommended by National Semiconductor's engineers)
before reading it.

If "rtc_delay" field of the platform data is true, the rtc driver
assumes that such delays are required. Although we have not seen
LP3974s without requiring such delays, we assume that such LP3974s
will be released soon (or they have done so already) and they are
supported by "lp3974" without setting "rtc_delay" at the platform
data.

This patch adds delays with msleep when writing values to RTC registers
if the platform data has rtc_delay set.

Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Reviewed-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2011-01-14 12:38:16 +01:00
Linus Torvalds 66dc918d42 Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6: (348 commits)
  ALSA: hda - Fix NULL-derefence with a single mic in STAC auto-mic detection
  ALSA: hda - Add missing NID 0x19 fixup for Sony VAIO
  ALSA: hda - Fix ALC275 enable hardware EQ for SONY VAIO
  ALSA: oxygen: fix Xonar DG input
  ALSA: hda - Fix EAPD on Lenovo NB ALC269 to low
  ALSA: hda - Fix missing EAPD for Acer 4930G
  ALSA: hda: Disable 4/6 channels on some NVIDIA GPUs.
  ALSA: hda - Add static_hdmi_pcm option to HDMI codec parser
  ALSA: hda - Don't refer ELD when unplugged
  ASoC: tpa6130a2: Fix compiler warning
  ASoC: tlv320dac33: Add DAPM selection for LOM invert
  ASoC: DMIC codec: Adding a generic DMIC codec
  ALSA: snd-usb-us122l: Fix missing NULL checks
  ALSA: snd-usb-us122l: Fix MIDI output
  ASoC: soc-cache: Fix invalid memory access during snd_soc_lzo_cache_sync()
  ASoC: Fix section mismatch in wm8995.c
  ALSA: oxygen: add S/PDIF source selection for Claro cards
  ALSA: oxygen: fix CD/MIDI for X-Meridian (2G)
  ASoC: fix migor audio build
  ALSA: include delay.h for msleep in Xonar DG support
  ...
2011-01-13 10:32:54 -08:00
Takashi Iwai 6db9a0f326 Merge branch 'topic/asoc' into for-linus 2011-01-13 08:37:24 +01:00
roel kluin fa63bd4aa5 regulator: missing index in PTR_ERR() in isl6271a_probe()
The index is missing so the return is wrong.

Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
2011-01-12 14:33:06 +00:00
Axel Lin 923430cfee regulator: Assign return value of mc13xxx_reg_rmw to ret
Otherwise, we will not return error if write to MC13892_SWITCHERS5 failed.

Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Yong Shen <yong.shen@linaro.org>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
2011-01-12 14:33:05 +00:00
Mark Brown 1130e5b3ff regulator: Add initial per-regulator debugfs support
We only expose the use and open counts to userspace, providing a tiny
bit of insight into what the API is up to.

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
2011-01-12 14:33:05 +00:00
Mark Brown 21cf891a47 regulator: Make regulator_has_full_constraints a bool
It's a boolean value so use the type.

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
2011-01-12 14:33:05 +00:00
Mark Brown 13ce29f80f regulator: Clean up logging a bit
The recent introduction of standard regulator API logging macros means
that all our log messages have at least the function name in them and
logging that the constraints are for the regulator API is probably a
bit much.

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
2011-01-12 14:33:05 +00:00
Mark Brown 95a3c23ae6 regulator: Optimise out noop voltage changes
If a consumer sets the same voltage range as is currently configured
for that consumer there's no need to run through setting the voltage
again. This pattern may occur with some CPUfreq implementations where
the same voltage range is used for multiple frequencies.

Reported-by: Saravana Kannan <skannan@codeaurora.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
2011-01-12 14:33:05 +00:00
Mark Brown 606a256281 regulator: Add API to re-apply voltage to hardware
When cooperating with an external control source the regulator setup
may be changed underneath the API. Currently consumers can just redo
the regulator_set_voltage() to restore a previously set configuration
but provide an explicit API for doing this as optimsations in the
regulator_set_voltage() implementation will shortly prevent that.

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
2011-01-12 14:33:05 +00:00
Mark Brown 27315cf61f regulator: Staticise non-exported functions in mc13892
No point exposing functions that aren't used elsewhere to the global
namespace and sparse warns about doing so.

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
2011-01-12 14:33:05 +00:00
Mark Brown ded06a5270 regulator: Only notify voltage changes when they succeed
Currently we notify a voltage change whenever we exit set_voltage(),
even if the change failed for some reason (eg, a constraints issue).
This shouldn't cause any substantial ill effects but is wasteful as
listeners get notified on noops. Fix this by moving the notification
into _do_set_voltage() and only notifying if we don't return an error.

Reported-by: Saravana Kannan <skannan@codeaurora.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
2011-01-12 14:33:05 +00:00
Mark Brown e8eef82b2c regulator: Provide a selector based set_voltage_sel() operation
Many regulator drivers implement voltage setting by looping through a
table of possible values, normally because the set of available voltages
can't be mapped onto selectors with simple calcuation. Factor out these
loops by providing a variant of set_voltage() which takes a selector rather
than a voltage range as an argument and implementing a loop through the
available selectors in the core.

This is not going to be suitable for use with all devices as when the
regulator voltage can be mapped onto selector values with a simple
calculation the linear scan through the available values will be more
expensive than just doing the calculation, especially for regulators
that provide fine grained voltage control.

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
2011-01-12 14:33:04 +00:00
Mark Brown 7579025130 regulator: Factor out voltage set operation into a separate function
Push all the callers of the chip set_voltage() operation out into a single
function to facilitiate future refactoring.

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
2011-01-12 14:33:04 +00:00
Mark Brown d9f0f28717 regulator: Convert WM8994 to use get_voltage_sel()
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
2011-01-12 14:33:04 +00:00
Mark Brown c24516a1d6 regulator: Convert WM835x to use get_voltage_sel()
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
2011-01-12 14:33:04 +00:00
Mark Brown 4d7071f1fd regulator: Allow modular build of mc13xxx-core
Since the MFD core for this device and the regulator drivers for these
devices can be built modular we should also support modular build of
the shared code for the regulator drivers, otherwise we try to link
built in code against modular code with unfortunate results.

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
2011-01-12 14:33:03 +00:00
Yong Shen 5e428d5cec regulator: support PMIC mc13892
add support for mc13892, tested on mx51 babbage board

Signed-off-by: Arnaud Patard <arnaud.patard@rtp-net.org>
Signed-off-by: Yong Shen <yong.shen@linaro.org>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
2011-01-12 14:33:03 +00:00
Yong Shen 167e3d8af9 make mc13783 regulator code generic
move some common functions and micros of mc13783 regulaor driver to
a seperate file, which makes it possible for mc13892 to share code.

Signed-off-by: Yong Shen <yong.shen@linaro.org>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
2011-01-12 14:33:03 +00:00
Yong Shen 57c78e359a Change the register name definitions for mc13783
To make mc13783 and mc13892 share code, the register names should be
changed to fit the new macro definitions in the comming patch.

Signed-off-by: Yong Shen <yong.shen@linaro.org>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
2011-01-12 14:33:03 +00:00
Bengt Jonsson 6909b4522e regulators: Removed macros for initialization of ab8500 regulators
This patch removes the macros for initializing the regulators.
The purpose is to remove one layer of abstraction and make the
code easier to read.

Signed-off-by: Bengt Jonsson <bengt.g.jonsson@stericsson.com>
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
2011-01-12 14:33:03 +00:00
Bengt Jonsson 09aefa12ac regulators: Added verbose debug messages to ab8500 regulators
The verbose debug outputs register writes and reads that can be
used to debug the driver.

Signed-off-by: Bengt Jonsson <bengt.g.jonsson@stericsson.com>
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
2011-01-12 14:33:03 +00:00
Bengt Jonsson fc24b426ff regulators: Modified ab8500 error handling
Error handling is updated to catch NULL pointer errors.

Signed-off-by: Bengt Jonsson <bengt.g.jonsson@stericsson.com>
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
2011-01-12 14:33:02 +00:00
Bengt Jonsson e1159e6d9a regulators: Updated ab8500 variable names, macro names and comments
The regulator enumeration is used for putting the regulator data
in correct place in the info array. This should be matched in the
board configuration.

Variable names are updated to be more consistent, comments are
corrected and macros have been edited to be consistent.

Signed-off-by: Bengt Jonsson <bengt.g.jonsson@stericsson.com>
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
2011-01-12 14:33:02 +00:00
Bengt Jonsson 2b75151a10 regulators: Added ab8500 v2 support
The AUX3 regulator voltage setting is changed in ab8500 v2 compared
to ab8500 v1. This patch adds v2 support while keeping support for
v1.

Signed-off-by: Bengt Jonsson <bengt.g.jonsson@stericsson.com>
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
2011-01-12 14:33:02 +00:00
Bengt Jonsson deaca1ee82 regulators: Clean out unused code in ab8500 regulators
The find_regulator function was unused so it has been removed. The
ab8500 pointer in the regulator info structure was unused and so it
has also been removed.

Signed-off-by: Bengt Jonsson <bengt.g.jonsson@stericsson.com>
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
2011-01-12 14:33:02 +00:00
Bengt Jonsson 65e03ed2d0 regulators: Fixed errors in ab8500 register mapping
For INTCORE and TVOUT regulators, the low power register bit is
included in the mask so that enable will set the regulator in
normal (high power) mode.

ANAMIC1, ANAMIC2, DMIC regulator settings are swapped with each
other so that the correct regulator gets enabled/disabled.

ANA regulator register address is corrected.

Signed-off-by: Bengt Jonsson <bengt.g.jonsson@stericsson.com>
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
2011-01-12 14:33:02 +00:00
Bengt Jonsson cb189b07d5 regulators: Moved define for number of regulators in ab8500
The define for number of regulators is moved from ab8500-core to
ab8500-regulator so that the regulator driver can be updated
independently of ab8500-core. This also changes the platform
configuration structure of ab8500-core so that it contains a
pointer to the regulator_init_data array plus number of
regulators instead of an fixed size array of pointers to
regulator_init_data.

Signed-off-by: Bengt Jonsson <bengt.g.jonsson@stericsson.com>
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
2011-01-12 14:33:02 +00:00
Cyril Chemparathy 1394fd2826 regulator: add driver for tps6524x regulator
TPS6524X provides three step-down converters and two general-purpose LDO
voltage regulators.  This device is interfaced using SPI.

Signed-off-by: Cyril Chemparathy <cyril@ti.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
2011-01-12 14:33:02 +00:00
Mark Brown afb8bb805b regulator: Convert WM831x drivers to use get_voltage_sel()
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
2011-01-12 14:33:02 +00:00
Mark Brown 476c2d83c7 regulator: Allow drivers to report voltages as selectors
Since drivers already have to provide an API for translating selectors
into voltages they may as well just report the selector values directly
to the core API rather than implement the lookup themselves. The old
interface is left in place for now, but may be removed in future.

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
2011-01-12 14:33:01 +00:00
Mark Brown 1bf5a1f86a regulator: Use _regulator_get_voltage() consistently
Rather than referencing the get_voltage() operation directly in the
ops struct use the internal _regulator_get_voltage() API call to do
so, facilitating refactoring.

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
2011-01-12 14:33:01 +00:00
Joe Perches 43e7ee33f2 drivers/regulator: Update WARN uses
Align arguments.

Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
2011-01-12 14:33:01 +00:00
Thomas Petazzoni 05fda3b1ab regulator: Take into account the requirements of all consumers
Extend the regulator_set_voltage() function to take into account the
voltage requirements of all consumers of the regulator being changed,
in order to set the voltage to the minimum voltage acceptable to all
consumers. The existing behaviour was that the latest
regulator_set_voltage() call would win over previous
regulator_set_voltage() calls even if setting the voltage to a
non-acceptable level from other consumers.

Signed-off-by: Thomas Petazzoni <t-petazzoni@ti.com>
Cc: Liam Girdwood <lrg@slimlogic.co.uk>
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
2011-01-12 14:33:01 +00:00
Joe Perches 5da84fd99b regulator: Add and use rdev_<level> macros
On Tue, 2010-11-30 at 10:52 +0000, Mark Brown wrote:
> On Mon, Nov 29, 2010 at 05:12:56PM -0800, Joe Perches wrote:
> > Just to please broonie...
> > Signed-off-by: Joe Perches <joe@perches.com>
> As usual when fixing review issues please revise your original patch
> rather than posting a fresh patch.

Here's an earlier comment:

On Thu, 2010-11-18 at 13:30 +0000, Mark Brown wrote:
> This looks reasonable, please rebase on top of Daniel's patches and
> submit it properly (with changelog and so on).

Sometimes it's simpler for an upstream maintainer to do
something like:

git am -s <patch1.mbox>
patch -p1 < patch2.mbox
git commit --amend file

instead of back and forthing.

Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
2011-01-12 14:33:01 +00:00
Mark Brown 6220b87bfd regulator: Remove duplicate consts from mc13873 driver voltage tables
They're not needed and sparse is verbosely upset about them.

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
2011-01-12 14:33:01 +00:00
Mark Brown f8c12fe329 regulator: Copy constraints from regulators when initialising them
Currently the regulator API uses the constraints structure passed in to
the core throughout the lifetime of the object. This means that it is not
possible to mark the constraints as __initdata so if the kernel supports
many boards the constraints for all of them are kept around throughout the
lifetime of the system, consuming memory needlessly. By copying constraints
that are actually used we allow the use of __initdata, saving memory when
multiple boards are supported.

This also means the constraints can be const.

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
2011-01-12 14:33:01 +00:00
Mark Brown f4d6adf11b regulator: Fix prototype for MAX8998 buck set_voltage()
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
2011-01-12 14:33:01 +00:00
Mark Brown 50ba5ca4be regulator: Remove regulator core version announcement
The version hasn't been updated since the regulator API was merged in
2.6.27 so just remove it - now we're in mainline the kernel version is
much more useful.

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
2011-01-12 14:33:00 +00:00
Mark Brown 4c35508fc0 regulator: Fix obfuscated log messages
Don't use %s to format fixed static strings into log messages, it just
makes searching for and reading the message in the kernel source
needlessly hard.

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
2011-01-12 14:33:00 +00:00
Daniel Walker 1d7372e15e drivers: regulator: core: convert to using pr_ macros
The regulator framework uses a lot of printks with a
specific formatting using __func__. This converts them
to use pr_ calls with a central format string.

Cc: bleong@codeaurora.org
Signed-off-by: Daniel Walker <dwalker@codeaurora.org>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
2011-01-12 14:33:00 +00:00
Daniel Walker c5e28ed782 drivers: regulator: core: use pr_fmt
This adds a pr_fmt line which uses the __func__ macro. I also
convert the current pr_ lines to remove their __func__ usage.

Cc: bleong@codeaurora.org
Signed-off-by: Daniel Walker <dwalker@codeaurora.org>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
2011-01-12 14:33:00 +00:00
Mark Brown 7bed08c565 regulator: Fix typo in PCAP regulator_set_voltage()
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
2011-01-12 14:33:00 +00:00
Bengt Jonsson acaf6ffefd regulator: enable supply regulator only when use count is zero
Supply regulators are disabled only when the last
reference count is removed on the child regulator
(the use count goes from 1 to 0). This patch changes
the behaviour of enable so the supply regulator is
enabled only when the use count of the child
regulator goes from 0 to 1.

Signed-off-by: Bengt Jonsson <bengt.g.jonsson@stericsson.com>
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
2011-01-12 14:33:00 +00:00
Mark Brown 02fa3ec01a regulator: Add basic trace facilities
Provide some basic trace facilities to the regulator API. We generate
events on regulator enable, disable and voltage setting over the actual
hardware operations (which are assumed to be the expensive ones which
require interaction with the actual device). This is intended to facilitate
debug of the performance and behaviour with consumers allowing unified
traces to be generated including the regulator operations within the
context of the other components of the system.

For enable we log the explicit delay for the voltage ramp separately to
the interaction with the hardware to highlight the time consumed in I/O.
We should add a similar delay for voltage changes, though there the
relatively small magnitude of the changes in the context of the I/O
costs makes it much less critical for most regulators.

Only hardware interactions are currently traced as the primary focus is
on the performance and synchronisation of actual hardware interactions.
Additional tracepoints for debugging of the logical operations can be
added later if required.

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
2011-01-12 14:33:00 +00:00
Mark Brown 3a93f2a9f4 regulator: Report actual configured voltage to set_voltage()
Change the interface used by set_voltage() to report the selected value
to the regulator core in terms of a selector used by list_voltage().
This allows the regulator core to know the voltage that was chosen
without having to do an explict get_voltage(), which would be much more
expensive as it will generally access hardware.

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
2011-01-12 14:32:59 +00:00
Mattias Wallin 63cee94614 regulator: lock supply in regulator enable
This patch add locks around regulator supply enable.

Signed-off-by: Mattias Wallin <mattias.wallin@stericsson.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
2011-01-12 14:32:59 +00:00
Mark Brown 5a7743edac regulator: Update LDO2 for WM8958
LDO2 has a slightly different range of supported voltages on WM8958
so update the selector<->voltage mappings to match.

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
2010-12-13 17:36:10 +00:00
Danny Huang 1b39ed0cf5 regulator: tps6586x: correct register table
Correct the register table for SM2, LDO8, RTC

Change-Id: I45348cec5ffbb7da9bd7523764fb611b537236b8
Signed-off-by: Danny Huang <dahuang@nvidia.com>
Signed-off-by: Olof Johansson <olofj@chromium.org>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
2010-12-09 09:23:43 +00:00