Pull x86 fixes from Ingo Molnar:
"Misc fixes from all around the place:
- a KASLR related revert where we ran out of time to get a fix - this
represents a substantial portion of the diffstat,
- two FPU fixes,
- two x86 platform fixes: an ACPI reduced-hw fix and a NumaChip fix,
- an entry code fix,
- and a VDSO build fix"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
Revert "x86/mm/ASLR: Propagate base load address calculation"
x86/fpu: Drop_fpu() should not assume that tsk equals current
x86/fpu: Avoid math_state_restore() without used_math() in __restore_xstate_sig()
x86/apic/numachip: Fix sibling map with NumaChip
x86/platform, acpi: Bypass legacy PIC and PIT in ACPI hardware reduced mode
x86/asm/entry/32: Fix user_mode() misuses
x86/vdso: Fix the build on GCC5
If we fail during our sanity tests we could get NULL deref's because we unload
the module before the dummy extent buffers are free'd via RCU. So check for
this case and just free the things directly. Thanks,
Signed-off-by: Josef Bacik <jbacik@fb.com>
My fix
Btrfs: fix merge delalloc logic
only fixed half of the problems, it didn't fix the case where we have two large
extents on either side and then join them together with a new small extent. We
need to instead keep track of how many extents we have accounted for with each
side of the new extent, and then see how many extents we need for the new large
extent. If they match then we know we need to keep our reservation, otherwise
we need to drop our reservation. This shows up with a case like this
[BTRFS_MAX_EXTENT_SIZE+4K][4K HOLE][BTRFS_MAX_EXTENT_SIZE+4K]
Previously the logic would have said that the number extents required for the
new size (3) is larger than the number of extents required for the largest side
(2) therefore we need to keep our reservation. But this isn't the case, since
both sides require a reservation of 2 which leads to 4 for the whole range
currently reserved, but we only need 3, so we need to drop one of the
reservations. The same problem existed for splits, we'd think we only need 3
extents when creating the hole but in reality we need 4. Thanks,
Signed-off-by: Josef Bacik <jbacik@fb.com>
486b908 (HID: wacom: do not send pen events before touch is up/forced out)
introduces a kernel oops when plugging a tablet without touch.
wacom->shared is null for these devices so this leads to a null pointer
exception.
Change the condition to make it clear that what we need is wacom->shared
not NULL.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The commit breaks the legacy platforms, ie. these not using device-tree,
and setting up the interrupt resources with a flag to activate edge
detection. The issue was found on the zylonite platform.
The reason is that zylonite uses platform resources to pass the interrupt number
and the irq flags (here IORESOURCE_IRQ_HIGHEDGE). It expects the driver to
request the irq with these flags, which in turn setups the irq as high edge
triggered.
After the patch, this was supposed to be taken care of with :
irq_resflags = irqd_get_trigger_type(irq_get_irq_data(ndev->irq));
But irq_resflags is 0 for legacy platforms, while for example in
arch/arm/mach-pxa/zylonite.c, in struct resource smc91x_resources[] the
irq flag is specified. This breaks zylonite because the interrupt is not
setup as triggered, and hardware doesn't provide interrupts.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
After commit 2b0bb01b6e, the kernel returns -ENOBUFS when user tries to add
an existing tunnel with ioctl API:
$ ip -6 tunnel add ip6tnl1 mode ip6ip6 dev eth1
add tunnel "ip6tnl0" failed: No buffer space available
It's confusing, the right error is EEXIST.
This patch also change a bit the code returned:
- ENOBUFS -> ENOMEM
- ENOENT -> ENODEV
Fixes: 2b0bb01b6e ("ip6_tunnel: Return an error when adding an existing tunnel.")
CC: Steffen Klassert <steffen.klassert@secunet.com>
Reported-by: Pierre Cheynier <me@pierre-cheynier.net>
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The argument 'flags' was missing in ndo_bridge_setlink().
ndo_bridge_dellink() was missing.
Fixes: 407af3299e ("bridge: Add netlink interface to configure vlans on bridge ports")
Fixes: add511b382 ("bridge: add flags argument to ndo_bridge_setlink and ndo_bridge_dellink")
CC: Vlad Yasevich <vyasevic@redhat.com>
CC: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The two main fixes here from Javier and Doug both fix issues seen on the
Exynos-based ARM Chromebooks with reference counting of GPIO regulators
over system suspend. The GPIO enable code didn't properly take account
of this cases (a full analysis is in Doug's commit log). This is fixed
by both fixing the reference counting directly and by making the resume
code skip enables it doesn't need to do. We could skip the change in
the resume code but it's a very simple change and adds extra robustness
against problems in other drivers.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJVCBjKAAoJECTWi3JdVIfQiA4H/2/zS+bEGIJs0yquAsmNT0as
v1XW+K8pw8klcCUbUpBgeqwBDmhiHHJtL5AWuC68KZHLRmg4+ryRdCyUgZ51AyJ4
4obGKxVrWpO0xM3BLeoeCc0ZSAAQzVuxplFSyFEbE14ULUKBqsVS8YKD2+FyrDRL
0RPAdNDak2Z7HD60W6234qqGfmEW0e1NAYTuZ7sCjE4dp8+S8OeauuwT489tuGt7
7N+BusHHnjWASW3tcitANTE8f3l3K4b5sUueolxi+ZghnrcxHcZn7LlKbVj0tpiF
yOCjc6jiLUL5UiCZ5q5IhamKPCTpTf/9LJlsjoSmj3Ze4PXn9/rEPW3wrIUyAh4=
=Dxlj
-----END PGP SIGNATURE-----
Merge tag 'regulator-fix-v4.0-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator
Pull regulator fixes from Mark Brown:
"The two main fixes here from Javier and Doug both fix issues seen on
the Exynos-based ARM Chromebooks with reference counting of GPIO
regulators over system suspend. The GPIO enable code didn't properly
take account of this case (a full analysis is in Doug's commit log).
This is fixed by both fixing the reference counting directly and by
making the resume code skip enables it doesn't need to do. We could
skip the change in the resume code but it's a very simple change and
adds extra robustness against problems in other drivers"
* tag 'regulator-fix-v4.0-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator:
regulator: tps65910: Add missing #include <linux/of.h>
regulator: core: Fix enable GPIO reference counting
regulator: Only enable disabled regulators on resume
A few things here:
- A change from Lars to fix insertion of cache values at the start of
rather than end of a rbtree block. This hadn't been noticed before
since almost everything lists registers in ascending order.
- A fix from Takashi for spurious warnings during cache sync with read
once registers, a problem which can be very noticeable on devices
that it affects.
- A fix from Valentin for a tighening of the oneshot IRQ request
interface which would have broken affected devices.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJVCAncAAoJECTWi3JdVIfQ3UwH/R94Youeta69sJvSpao38Luo
jSj6A+zA2x2azwOTNdZ8F4vdqetoabvt8enXR0zxQnx86JP3zYFoEZcos7Bn4HRX
E85Fn8RNLHVP0NmUdZefvSztG5A0Glf9FxEqoSfGb6r0FztYnjJ3fCEoDO8NYE8S
xkeFvznLyPGeU39BMXuqROEUN4BNVeQ6ijIQBsP9tIpgIQA9lIzW4vSqTXvGiwLU
UrPTYpPpVukKGwYD6UB8GQ14M3KDAmzvSTiCO7hal1NUdgtOWqObR2YALhMWBV6z
bygbobrVGaaxmdb3maEol3h9tCxY6G+5Pcwhl0JDZdVd2McXa2oMMxQ/r1kgcxY=
=t8iv
-----END PGP SIGNATURE-----
Merge tag 'regmap-v4.0-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap
Pull regmap fixes from Mark Brown:
"A few things here:
- a change from Lars to fix insertion of cache values at the start of
rather than end of a rbtree block. This hadn't been noticed before
since almost everything lists registers in ascending order.
- a fix from Takashi for spurious warnings during cache sync with
read once registers, a problem which can be very noticeable on
devices that it affects.
- a fix from Valentin for a tighening of the oneshot IRQ request
interface which would have broken affected devices"
* tag 'regmap-v4.0-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap:
regmap: regcache-rbtree: Fix present bitmap resize
regmap: Skip read-only registers in regcache_sync()
regmap-irq: set IRQF_ONESHOT flag to ensure IRQ request
more minor issues with our virtio 1.0 drivers just introduced in the
kernel.
(I would normally use my fixes branch for this, but there were a batch of them...)
Thanks,
Rusty.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=8QwR
-----END PGP SIGNATURE-----
Merge tag 'virtio-next-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux
Pull virtio fixes from Rusty Russell:
"Not entirely surprising: the ongoing QEMU work on virtio 1.0 has
revealed more minor issues with our virtio 1.0 drivers just introduced
in the kernel.
(I would normally use my fixes branch for this, but there were a batch
of them...)"
* tag 'virtio-next-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux:
virtio_mmio: fix access width for mmio
uapi/virtio_scsi: allow overriding CDB/SENSE size
virtio_mmio: generation support
virtio_rpmsg: set DRIVER_OK before using device
9p/trans_virtio: fix hot-unplug
virtio-balloon: do not call blocking ops when !TASK_RUNNING
virtio_blk: fix comment for virtio 1.0
virtio_blk: typo fix
virtio_balloon: set DRIVER_OK before using device
virtio_console: avoid config access from irq
virtio_console: init work unconditionally
Pull kvm fixes from Marcelo Tosatti:
"KVM bug fixes (ARM and x86)"
* git://git.kernel.org/pub/scm/virt/kvm/kvm:
arm/arm64: KVM: Keep elrsr/aisr in sync with software model
KVM: VMX: Set msr bitmap correctly if vcpu is in guest mode
arm/arm64: KVM: fix missing unlock on error in kvm_vgic_create()
kvm: x86: i8259: return initialized data on invalid-size read
arm64: KVM: Fix outdated comment about VTCR_EL2.PS
arm64: KVM: Do not use pgd_index to index stage-2 pgd
arm64: KVM: Fix stage-2 PGD allocation to have per-page refcounting
kvm: move advertising of KVM_CAP_IRQFD to common code
As pointed by recent post[1] on exploiting DRAM physical imperfection,
/proc/PID/pagemap exposes sensitive information which can be used to do
attacks.
This disallows anybody without CAP_SYS_ADMIN to read the pagemap.
[1] http://googleprojectzero.blogspot.com/2015/03/exploiting-dram-rowhammer-bug-to-gain.html
[ Eventually we might want to do anything more finegrained, but for now
this is the simple model. - Linus ]
Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Acked-by: Konstantin Khlebnikov <khlebnikov@openvz.org>
Acked-by: Andy Lutomirski <luto@amacapital.net>
Cc: Pavel Emelyanov <xemul@parallels.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Mark Seaborn <mseaborn@chromium.org>
Cc: stable@vger.kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
As well as the usual collection of driver specific fixes there's a few
more generic things:
- Lots of fixes from Takashi for drivers using the wrong field in the
control union to communicate with userspace, leading to potential
errors on 64 bit systems.
- A fix from Lars for locking of the lists of devices we maintain,
mostly only likely to trigger during device probe and removal.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJVCA+HAAoJECTWi3JdVIfQ6oQIAIOFlrPzKpI3C7MqrK6F+ySC
g/JOf8XZKbStl+RdSu/RI6gL1Nc4VD7EHv5vEM2Br6KtUHQMoQYpsSiPvn1BFJBX
EkwY3eoDiIyPqQG7cGmdIF/8NXiZgJYh13coamrkdAhBFMXfmqlbrBHo71Z6o1ic
cg4rng3AmjyJ1NfUDsMW/KTX0F8AUTw7yYs+B4pyjfRBFVmhmzubXGXNjiW+/Tz4
zjk9c3Qm7ZxC66dbvg5lpIakwbRtX26p7Fn+pWOewL4y81y9qruSvV6IgDZ1RO95
DRtLsU7qyIK3G9zCw61xJNiL2QAfgOfYYgi7R6XrlS3nttIFT30oELw5ObwjSM0=
=iSeG
-----END PGP SIGNATURE-----
Merge tag 'asoc-fix-v4.0-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-linus
ASoC: Fixes for v4.0
As well as the usual collection of driver specific fixes there's a few
more generic things:
- Lots of fixes from Takashi for drivers using the wrong field in the
control union to communicate with userspace, leading to potential
errors on 64 bit systems.
- A fix from Lars for locking of the lists of devices we maintain,
mostly only likely to trigger during device probe and removal.
Writing the block group cache will modify the extent tree quite a bit because it
truncates the old space cache and pre-allocates new stuff. To try and cut down
on the churn lets do the setup dance first, then later on hopefully we can avoid
looping with newly dirtied roots. Thanks,
Signed-off-by: Josef Bacik <jbacik@fb.com>
There is a notifier that handles live patches for coming and going modules.
It takes klp_mutex lock to avoid races with coming and going patches but
it does not keep the lock all the time. Therefore the following races are
possible:
1. The notifier is called sometime in STATE_MODULE_COMING. The module
is visible by find_module() in this state all the time. It means that
new patch can be registered and enabled even before the notifier is
called. It might create wrong order of stacked patches, see below
for an example.
2. New patch could still see the module in the GOING state even after
the notifier has been called. It will try to initialize the related
object structures but the module could disappear at any time. There
will stay mess in the structures. It might even cause an invalid
memory access.
This patch solves the problem by adding a boolean variable into struct module.
The value is true after the coming and before the going handler is called.
New patches need to be applied when the value is true and they need to ignore
the module when the value is false.
Note that we need to know state of all modules on the system. The races are
related to new patches. Therefore we do not know what modules will get
patched.
Also note that we could not simply ignore going modules. The code from the
module could be called even in the GOING state until mod->exit() finishes.
If we start supporting patches with semantic changes between function
calls, we need to apply new patches to any still usable code.
See below for an example.
Finally note that the patch solves only the situation when a new patch is
registered. There are no such problems when the patch is being removed.
It does not matter who disable the patch first, whether the normal
disable_patch() or the module notifier. There is nothing to do
once the patch is disabled.
Alternative solutions:
======================
+ reject new patches when a patched module is coming or going; this is ugly
+ wait with adding new patch until the module leaves the COMING and GOING
states; this might be dangerous and complicated; we would need to release
kgr_lock in the middle of the patch registration to avoid a deadlock
with the coming and going handlers; also we might need a waitqueue for
each module which seems to be even bigger overhead than the boolean
+ stop modules from entering COMING and GOING states; wait until modules
leave these states when they are already there; looks complicated; we would
need to ignore the module that asked to stop the others to avoid a deadlock;
also it is unclear what to do when two modules asked to stop others and
both are in COMING state (situation when two new patches are applied)
+ always register/enable new patches and fix up the potential mess (registered
patches order) in klp_module_init(); this is nasty and prone to regressions
in the future development
+ add another MODULE_STATE where the kallsyms are visible but the module is not
used yet; this looks too complex; the module states are checked on "many"
locations
Example of patch stacking breakage:
===================================
The notifier could _not_ _simply_ ignore already initialized module objects.
For example, let's have three patches (P1, P2, P3) for functions a() and b()
where a() is from vmcore and b() is from a module M. Something like:
a() b()
P1 a1() b1()
P2 a2() b2()
P3 a3() b3(3)
If you load the module M after all patches are registered and enabled.
The ftrace ops for function a() and b() has listed the functions in this
order:
ops_a->func_stack -> list(a3,a2,a1)
ops_b->func_stack -> list(b3,b2,b1)
, so the pointer to b3() is the first and will be used.
Then you might have the following scenario. Let's start with state when patches
P1 and P2 are registered and enabled but the module M is not loaded. Then ftrace
ops for b() does not exist. Then we get into the following race:
CPU0 CPU1
load_module(M)
complete_formation()
mod->state = MODULE_STATE_COMING;
mutex_unlock(&module_mutex);
klp_register_patch(P3);
klp_enable_patch(P3);
# STATE 1
klp_module_notify(M)
klp_module_notify_coming(P1);
klp_module_notify_coming(P2);
klp_module_notify_coming(P3);
# STATE 2
The ftrace ops for a() and b() then looks:
STATE1:
ops_a->func_stack -> list(a3,a2,a1);
ops_b->func_stack -> list(b3);
STATE2:
ops_a->func_stack -> list(a3,a2,a1);
ops_b->func_stack -> list(b2,b1,b3);
therefore, b2() is used for the module but a3() is used for vmcore
because they were the last added.
Example of the race with going modules:
=======================================
CPU0 CPU1
delete_module() #SYSCALL
try_stop_module()
mod->state = MODULE_STATE_GOING;
mutex_unlock(&module_mutex);
klp_register_patch()
klp_enable_patch()
#save place to switch universe
b() # from module that is going
a() # from core (patched)
mod->exit();
Note that the function b() can be called until we call mod->exit().
If we do not apply patch against b() because it is in MODULE_STATE_GOING,
it will call patched a() with modified semantic and things might get wrong.
[jpoimboe@redhat.com: use one boolean instead of two]
Signed-off-by: Petr Mladek <pmladek@suse.cz>
Acked-by: Josh Poimboeuf <jpoimboe@redhat.com>
Acked-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Going over the virtio mmio code, I noticed that it doesn't correctly
access modern device config values using "natural" accessors: it uses
readb to get/set them byte by byte, while the virtio 1.0 spec explicitly states:
4.2.2.2 Driver Requirements: MMIO Device Register Layout
...
The driver MUST only use 32 bit wide and aligned reads and writes to
access the control registers described in table 4.1.
For the device-specific configuration space, the driver MUST use
8 bit wide accesses for 8 bit wide fields, 16 bit wide and aligned
accesses for 16 bit wide fields and 32 bit wide and aligned accesses for
32 and 64 bit wide fields.
Borrow code from virtio_pci_modern to do this correctly.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
nouveau fixes, and gm206 modesetting enables.
* 'linux-4.0' of git://anongit.freedesktop.org/git/nouveau/linux-2.6:
drm/nouveau/bios: fix i2c table parsing for dcb 4.1
drm/nouveau/device/gm100: Basic GM206 bring up (as copy of GM204)
drm/nouveau/device: post write to NV_PMC_BOOT_1 when flipping endian switch
drm/nouveau/gr/gf100: fix some accidental or'ing of buffer addresses
drm/nouveau/fifo/nv04: remove the loop from the interrupt handler
Code before looked only at bit 31 to decide if a port is unused.
However dcb 4.1 spec says 0x1F in bits 31-27 and 26-22 means unused.
This fixed hdmi monitor detection on GM206.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Complete bong hit (and not the last...), the hardware will reassert the
interrupt to PMC if it's necessary.
Also potentially harmful in the face of interrupts such as the non-stall
interrupt, which remain active in NV_PFIFO_INTR even when we don't care
about servicing it.
It appears (hopefully, fdo#87244), that under certain loads, the methods
may pass quickly enough to hit the "100 spins and kill PFIFO" thing that
we had going on. Not ideal ;)
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Fixes page refcounting issues in our Stage-2 page table management code,
fixes a missing unlock in a gicv3 error path, and fixes a race that can
cause lost interrupts if signals are pending just prior to entering the
guest.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJVBs95AAoJEEtpOizt6ddyAfoH/Rwj2T38ZDikImPpgfeFrmJs
ZlWC+Z3akwjVHPv308/MsKdyashtA7OjiMp3DOheMFMYJay/ecgY/92vFCc6uh5S
LDoXCbp+Pneth6C6bbU2Gw+aoCD07ZYCn9PeFq40MfpQUhCEGWhx41OFzHppqOZx
e+jodHRE+sBVTFUtbz+HubAfcM46f/8bP7682CEKsVZPeTSiHyeojdZEglfB37MG
ar/iC1/cyO/097vWaBqv1t1WZoHbWmMrDlzo5X+AtayVXFNdv4Ztw0Rz2kRhnLB8
8GXYawoSQoTN8FX1oyTyr5YWcWD7wDTzhcHsHS1xZHhvrdLCEcFrHeEWkuUlYjU=
=YS6j
-----END PGP SIGNATURE-----
Merge tag 'kvm-arm-fixes-4.0-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/kvmarm/kvmarm
Fixes for KVM/ARM for 4.0-rc5.
Fixes page refcounting issues in our Stage-2 page table management code,
fixes a missing unlock in a gicv3 error path, and fixes a race that can
cause lost interrupts if signals are pending just prior to entering the
guest.
The current CP firmware can handle Usermode Queues only on MEC1.
To reflect this firmware change, this commit reduces number of compute pipelines
to 4 - 1, from 8 - 1 (the first pipeline is allocated for kgd).
Signed-off-by: Ben Goz <ben.goz@amd.com>
Signed-off-by: Oded Gabbay <oded.gabbay@amd.com>
Cc: stable@vger.kernel.org
This patch fixes the SDMA queue initialization, when running in non-HWS mode.
The first fix is to move the initialization of SDMA VM parameters before the
initialization of the SDMA MQD.
The second fix is to load the MQD to an HQD after the initialization of the MQD.
Signed-off-by: Ben Goz <ben.goz@amd.com>
Signed-off-by: Oded Gabbay <oded.gabbay@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
This patch adds a missing destruction of mqd, when destroying a kernel queue.
Without the destruction, there is a memory leakage when repeatedly creating and
destroying kernel queues.
Signed-off-by: Ben Goz <ben.goz@amd.com>
Signed-off-by: Oded Gabbay <oded.gabbay@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
E1x chips (57710, 57711(E)) have no support for encapsulation
offload. bnx2x incorrectly advertises the support as available.
Setting of those features is conditional on "!CHIP_IS_E1x(bp)", but
the bp struct is not initialized yet at this point and consequently
any chip passes the check.
The check must use the "chip_is_e1x" local variable instead to work
correctly.
Signed-off-by: Michal Schmidt <mschmidt@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the part of the compression data are corrupted, or the compression
data is totally fake, the memory access over the limit is possible.
This is the log from my system usning lz4 decompression.
[6502]data abort, halting
[6503]r0 0x00000000 r1 0x00000000 r2 0xdcea0ffc r3 0xdcea0ffc
[6509]r4 0xb9ab0bfd r5 0xdcea0ffc r6 0xdcea0ff8 r7 0xdce80000
[6515]r8 0x00000000 r9 0x00000000 r10 0x00000000 r11 0xb9a98000
[6522]r12 0xdcea1000 usp 0x00000000 ulr 0x00000000 pc 0x820149bc
[6528]spsr 0x400001f3
and the memory addresses of some variables at the moment are
ref:0xdcea0ffc, op:0xdcea0ffc, oend:0xdcea1000
As you can see, COPYLENGH is 8bytes, so @ref and @op can access the momory
over @oend.
Signed-off-by: JeHyeon Yeon <tom.yeon@windriver.com>
Reviewed-by: David Sterba <dsterba@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Kernfs supports two styles of read: direct_read and seqfile_read.
The latter supports 'poll' correctly thanks to the update of
'->event' in kernfs_seq_show.
The former does not as '->event' is never updated on a read.
So add an appropriate update in kernfs_file_direct_read().
This was noticed because some 'md' sysfs attributes were
recently changed to use direct reads.
Reported-by: Prakash Punnoor <prakash@punnoor.de>
Reported-by: Torsten Kaiser <just.for.lkml@googlemail.com>
Fixes: 750f199ee8
Signed-off-by: NeilBrown <neilb@suse.de>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* disable U-APSD for better interoperability, from Michal Kazior
* drop unencrypted frames in mesh forwarding, from Bob Copeland
* treat non-QoS/WMM HT stations as non-HT, to fix confusion when
they connect and then get QoS packets anyway due to HT
* fix counting interfaces for combination checks, otherwise the
interface combinations aren't properly enforced (from Andrei)
* fix pure ECSA by reacting to the IE change
* ignore erroneous (E)CSA to the current channel which sometimes
happens due to AP/GO bugs
-----BEGIN PGP SIGNATURE-----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=Ecdh
-----END PGP SIGNATURE-----
Merge tag 'mac80211-for-davem-2015-03-16' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211
Johannes Berg says:
====================
Here are a few fixes that I'd like to still get in:
* disable U-APSD for better interoperability, from Michal Kazior
* drop unencrypted frames in mesh forwarding, from Bob Copeland
* treat non-QoS/WMM HT stations as non-HT, to fix confusion when
they connect and then get QoS packets anyway due to HT
* fix counting interfaces for combination checks, otherwise the
interface combinations aren't properly enforced (from Andrei)
* fix pure ECSA by reacting to the IE change
* ignore erroneous (E)CSA to the current channel which sometimes
happens due to AP/GO bugs
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Steffen Klassert says:
====================
pull request (net): ipsec 2015-03-16
1) Fix the network header offset in _decode_session6
when multiple IPv6 extension headers are present.
From Hajime Tazaki.
2) Fix an interfamily tunnel crash. We set outer mode
protocol too early and may dispatch to the wrong
address family. Move the setting of the outer mode
protocol behind the last accessing of the inner mode
to fix the crash.
3) Most callers of xfrm_lookup() expect that dst_orig
is released on error. But xfrm_lookup_route() may
need dst_orig to handle certain error cases. So
introduce a flag that tells what should be done in
case of error. From Huaibin Wang.
Please pull or let me know if there are problems.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The commit 9cade1a46c (dma: dw: split driver to library part and platform
code) introduced a separate platform driver but missed to add a
MODULE_ALIAS("platform:dw_dmac"); to that module.
The patch adds this to get driver loaded automatically if platform device is
registered.
Reported-by: "Blin, Jerome" <jerome.blin@intel.com>
Fixes: 9cade1a46c (dma: dw: split driver to library part and platform code)
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The commit [ef403edb7558: ALSA: hda - Don't access stereo amps for
mono channel widgets] fixed the handling of mono widgets in general,
but it still misses an exceptional case: namely, a mono mixer widget
taking a single stereo input. In this case, it has stereo volumes
although it's a mono widget, and thus we have to take care of both
left and right input channels, as stated in HD-audio spec ("7.1.3
Widget Interconnection Rules").
This patch covers this missing piece by adding proper checks of stereo
amps in both the generic parser and the proc output codes.
Reported-by: Raymond Yau <superquad.vortex2@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
drivers/regulator/tps65910-regulator.c: In function ‘tps65910_parse_dt_reg_data’:
drivers/regulator/tps65910-regulator.c:1018: error: implicit declaration of function ‘of_get_child_by_name’
drivers/regulator/tps65910-regulator.c:1018: warning: assignment makes pointer from integer without a cast
drivers/regulator/tps65910-regulator.c:1034: error: implicit declaration of function ‘of_node_put’
drivers/regulator/tps65910-regulator.c:1056: error: implicit declaration of function ‘of_property_read_u32’
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Below comments got from Page4724 of Reference Manual of i.mx6q:
http://cache.freescale.com/files/32bit/doc/ref_manual/IMX6DQRM.pdf
--"Static context mode should be used for the first channel called
after reset to ensure that the all context RAM for that channel is
initialized during the context SAVE phase when the channel is
done or yields. Subsequent calls to the same channel or
different channels may use any of the dynamic context modes.
This will ensure that all context locations for the bootload
channel are initialized, and prevent undefined values in context
RAM from being loaded during the context restore if the
channel is re-started later"
Unfortunately, the rule was broken by commit(5b28aa319b)
.This patch just take them back.
Signed-off-by: Robin Gong <b38343@freescale.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
This reverts commit:
f47233c2d3 ("x86/mm/ASLR: Propagate base load address calculation")
The main reason for the revert is that the new boot flag does not work
at all currently, and in order to make this work, we need non-trivial
changes to the x86 boot code which we didn't manage to get done in
time for merging.
And even if we did, they would've been too risky so instead of
rushing things and break booting 4.1 on boxes left and right, we
will be very strict and conservative and will take our time with
this to fix and test it properly.
Reported-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: Baoquan He <bhe@redhat.com>
Cc: H. Peter Anvin <hpa@linux.intel.com
Cc: Jiri Kosina <jkosina@suse.cz>
Cc: Josh Triplett <josh@joshtriplett.org>
Cc: Junjie Mao <eternal.n08@gmail.com>
Cc: Kees Cook <keescook@chromium.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Matt Fleming <matt.fleming@intel.com>
Link: http://lkml.kernel.org/r/20150316100628.GD22995@pd.tnic
Signed-off-by: Ingo Molnar <mingo@kernel.org>
plane->state->fb and plane->fb should always reference the same FB so
that atomic and legacy codepaths have the same view of display state.
However, there are some places in kernel code that directly set
plane->fb and neglect to update plane->state->fb. If we never do a
successful update through the atomic pipeline, the RmFB cleanup code
will look at the plane->state->fb pointer, which has never actually
been set to a legitimate value, and try to clean it up, leading to
BUG's.
Add a quick helper function to synchronize plane->state->fb with
plane->fb and call it everywhere the driver tries to manually set
plane->fb outside of the atomic pipeline. In this function, use
drm_atomic_set_fb_for_plane instead of writing plane->state->fb
directly to keep the reference count right.
This is modified from Matt Roper's patch to drm-intel-nightly with
commit id
commit afd65eb4cc
Author: Matt Roper <matthew.d.roper@intel.com>
Date: Tue Feb 3 13:10:04 2015 -0800
drm/i915: Ensure plane->state->fb stays in sync with plane->fb
However this bug exists in mainline kernel too, so I created this to fix
it in mainline kernel.
A minor change is to use drm_atomic_set_fb_for_plane instead of update
reference count manually.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=88909
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=93711
Signed-off-by: Xi Ruoyao <xry111@outlook.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
[Jani: included the patch notes in the commit message]
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
If the AP is confused and starts doing a CSA to the same channel,
just ignore that request instead of trying to act it out since it
was likely sent in error anyway.
In the case of the bug I was investigating the GO was misbehaving
and sending out a beacon with CSA IEs still included after having
actually done the channel switch.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
As HT/VHT depend heavily on QoS/WMM, it's not a good idea to
let userspace add clients that have HT/VHT but not QoS/WMM.
Since it does so in certain cases we've observed (client is
using HT IEs but not QoS/WMM) just ignore the HT/VHT info at
this point and don't pass it down to the drivers which might
unconditionally use it.
Cc: stable@vger.kernel.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When a beacon from the AP contains only the ECSA IE, and not a CSA IE
as well, this ECSA IE is not considered for calculating the CRC and
the beacon might be dropped as not being interesting. This is clearly
wrong, it should be handled and the channel switch should be executed.
Fix this by including the ECSA IE ID in the bitmap of interesting IEs.
Reported-by: Gil Tribush <gil.tribush@intel.com>
Reviewed-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Since moving the interface combination checks to mac80211, it's
broken because it now only considers interfaces with an assigned
channel context, so for example any interface that isn't active
can still be up, which is clearly an issue; also, in particular
P2P-Device wdevs are an issue since they never have a chanctx.
Fix this by counting running interfaces instead the ones with a
channel context assigned.
Cc: stable@vger.kernel.org [3.16+]
Fixes: 73de86a389 ("cfg80211/mac80211: move interface counting for combination check to mac80211")
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
[rewrite commit message, dig out the commit it fixes]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Follow commit 871341023c.
Kernel faults are expected to handle OOM conditions gracefully (gup,
uaccess etc.), so they should never invoke the OOM killer. Reserve
this for faults triggered in user context when it is the only option.
Signed-off-by: Ley Foon Tan <lftan@altera.com>
Linus Torvalds
Josef Bacik
Benjamin Tissoires
Robert Jarzmik
Eric Dumazet
Nicolas Dichtel
Kirill A. Shutemov
Takashi Iwai
Petr Mladek
Michael S. Tsirkin
Dave Airlie
Stefan Huehner
Ben Skeggs
Marcelo Tosatti
Ben Goz
Michal Schmidt
JeHyeon Yeon
NeilBrown
David S. Miller
Andy Shevchenko
Dmitry Torokhov
Mark Brown
Geert Uytterhoeven
Robin Gong
Borislav Petkov
Xi Ruoyao
Johannes Berg
Andrei Otcheretianski
Ley Foon Tan