Core:
* Remove support for asynchronous erase (not implemented by any of
the existing drivers anyway)
* Remove Cyrille from the list of SPI NOR and MTD maintainers
* Fix kernel doc headers
* Allow users to define the partitions parsers they want to test
through a DT property (compatible of the partitions subnode)
* Remove the bfin-async-flash driver (the only architecture using
it has been removed)
* Fix pagetest test
* Add extra checks in mtd_erase()
* Simplify the MTD partition creation logic and get rid of
mtd_add_device_partitions()
Drivers:
* Add endianness information to the physmap DT binding
* Add Eon EN29LV400A IDs to JEDEC probe logic
* Use %*ph where appropriate
SPI NOR changes:
Drivers:
* Make fsl-quaspi assign different names to MTD devices connected
to the same QSPI controller
* Remove an unneeded driver.bus assigned in the fsl-qspi driver
NAND changes:
Core:
* Prepare arrival of the SPI NAND subsystem by implementing a
generic (interface-agnostic) layer to ease manipulation of NAND
devices
* Move onenand code base to the drivers/mtd/nand/ dir
* Rework timing mode selection
* Provide a generic way for NAND chip drivers to flag a specific
GET/SET FEATURE operation as supported/unsupported
* Stop embedding ONFI/JEDEC param page in nand_chip
Drivers:
* Rework/cleanup of the mxc driver
* Various cleanups in the vf610 driver
* Migrate the fsmc and vf610 to ->exec_op()
* Get rid of the pxa driver (replaced by marvell_nand)
* Support ->setup_data_interface() in the GPMI driver
* Fix probe error path in several drivers
* Remove support for unused hw_syndrome mode in sunxi_nand
* Various minor improvements
-----BEGIN PGP SIGNATURE-----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=EG7L
-----END PGP SIGNATURE-----
Merge tag 'mtd/for-4.17' of git://git.infradead.org/linux-mtd
Pull MTD updates from Boris Brezillon:
"MTD Core:
- Remove support for asynchronous erase (not implemented by any of
the existing drivers anyway)
- Remove Cyrille from the list of SPI NOR and MTD maintainers
- Fix kernel doc headers
- Allow users to define the partitions parsers they want to test
through a DT property (compatible of the partitions subnode)
- Remove the bfin-async-flash driver (the only architecture using it
has been removed)
- Fix pagetest test
- Add extra checks in mtd_erase()
- Simplify the MTD partition creation logic and get rid of
mtd_add_device_partitions()
MTD Drivers:
- Add endianness information to the physmap DT binding
- Add Eon EN29LV400A IDs to JEDEC probe logic
- Use %*ph where appropriate
SPI NOR Drivers:
- Make fsl-quaspi assign different names to MTD devices connected to
the same QSPI controller
- Remove an unneeded driver.bus assigned in the fsl-qspi driver
NAND Core:
- Prepare arrival of the SPI NAND subsystem by implementing a generic
(interface-agnostic) layer to ease manipulation of NAND devices
- Move onenand code base to the drivers/mtd/nand/ dir
- Rework timing mode selection
- Provide a generic way for NAND chip drivers to flag a specific
GET/SET FEATURE operation as supported/unsupported
- Stop embedding ONFI/JEDEC param page in nand_chip
NAND Drivers:
- Rework/cleanup of the mxc driver
- Various cleanups in the vf610 driver
- Migrate the fsmc and vf610 to ->exec_op()
- Get rid of the pxa driver (replaced by marvell_nand)
- Support ->setup_data_interface() in the GPMI driver
- Fix probe error path in several drivers
- Remove support for unused hw_syndrome mode in sunxi_nand
- Various minor improvements"
* tag 'mtd/for-4.17' of git://git.infradead.org/linux-mtd: (89 commits)
dt-bindings: fsl-quadspi: Add the example of two SPI NOR
mtd: fsl-quadspi: Distinguish the mtd device names
mtd: nand: Fix some function description mismatches in core.c
mtd: fsl-quadspi: Remove unneeded driver.bus assignment
mtd: rawnand: marvell: Rename ->ecc_clk into ->core_clk
mtd: rawnand: s3c2410: enhance the probe function error path
mtd: rawnand: tango: fix probe function error path
mtd: rawnand: sh_flctl: fix the probe function error path
mtd: rawnand: omap2: fix the probe function error path
mtd: rawnand: mxc: fix probe function error path
mtd: rawnand: denali: fix probe function error path
mtd: rawnand: davinci: fix probe function error path
mtd: rawnand: cafe: fix probe function error path
mtd: rawnand: brcmnand: fix probe function error path
mtd: rawnand: sunxi: Stop supporting ECC_HW_SYNDROME mode
mtd: rawnand: marvell: Fix clock resource by adding a register clock
mtd: ftl: Use DIV_ROUND_UP()
mtd: Fix some function description mismatches in mtdcore.c
mtd: physmap_of: update struct map_info's swap as per map requirement
dt-bindings: mtd-physmap: Add endianness supports
...
This release brings up a new platform based on the old ARM9 core: the
Nuvoton NPCM is used as a baseboard management controller, competing
with the better known ASpeed AST2xx series.
Another important change is the addition of ARMv7-A based chips
in mach-stm32. The older parts in this platform are ARMv7-M based
microcontrollers, now they are expanding to general-purpose workloads.
The other changes are the usual defconfig updates to enable additional
drivers, lesser bugfixes. The largest updates as often are the ongoing
OMAP cleanups, but we also have a number of changes for the older
PXA and davinci platforms this time.
For the Renesas shmobile/r-car platform, some new infrastructure
is needed to make the watchdog work correctly.
Supporting Multiprocessing on Allwinner A80 required a significant
amount of new code, but is not doing anything unexpected.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=HD9V
-----END PGP SIGNATURE-----
Merge tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC platform updates from Arnd Bergmann:
"This release brings up a new platform based on the old ARM9 core: the
Nuvoton NPCM is used as a baseboard management controller, competing
with the better known ASpeed AST2xx series.
Another important change is the addition of ARMv7-A based chips in
mach-stm32. The older parts in this platform are ARMv7-M based
microcontrollers, now they are expanding to general-purpose workloads.
The other changes are the usual defconfig updates to enable additional
drivers, lesser bugfixes. The largest updates as often are the ongoing
OMAP cleanups, but we also have a number of changes for the older PXA
and davinci platforms this time.
For the Renesas shmobile/r-car platform, some new infrastructure is
needed to make the watchdog work correctly.
Supporting Multiprocessing on Allwinner A80 required a significant
amount of new code, but is not doing anything unexpected"
* tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (179 commits)
arm: npcm: modify configuration for the NPCM7xx BMC.
MAINTAINERS: update entry for ARM/berlin
ARM: omap2: fix am43xx build without L2X0
ARM: davinci: da8xx: simplify CFGCHIP regmap_config
ARM: davinci: da8xx: fix oops in USB PHY driver due to stack allocated platform_data
ARM: multi_v7_defconfig: add NXP FlexCAN IP support
ARM: multi_v7_defconfig: enable thermal driver for i.MX devices
ARM: multi_v7_defconfig: add RN5T618 PMIC family support
ARM: multi_v7_defconfig: add NXP graphics drivers
ARM: multi_v7_defconfig: add GPMI NAND controller support
ARM: multi_v7_defconfig: add OCOTP driver for NXP SoCs
ARM: multi_v7_defconfig: configure I2C driver built-in
arm64: defconfig: add CONFIG_UNIPHIER_THERMAL and CONFIG_SNI_AVE
ARM: imx: fix imx6sll-only build
ARM: imx: select ARM_CPU_SUSPEND for CPU_IDLE as well
ARM: mxs_defconfig: Re-sync defconfig
ARM: imx_v4_v5_defconfig: Use the generic fsl-asoc-card driver
ARM: imx_v4_v5_defconfig: Re-sync defconfig
arm64: defconfig: enable stmmac ethernet to defconfig
ARM: EXYNOS: Simplify code in coupled CPU idle hot path
...
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=RVhK
-----END PGP SIGNATURE-----
Merge tag 'for-4.17/block-20180402' of git://git.kernel.dk/linux-block
Pull block layer updates from Jens Axboe:
"It's a pretty quiet round this time, which is nice. This contains:
- series from Bart, cleaning up the way we set/test/clear atomic
queue flags.
- series from Bart, fixing races between gendisk and queue
registration and removal.
- set of bcache fixes and improvements from various folks, by way of
Michael Lyle.
- set of lightnvm updates from Matias, most of it being the 1.2 to
2.0 transition.
- removal of unused DIO flags from Nikolay.
- blk-mq/sbitmap memory ordering fixes from Omar.
- divide-by-zero fix for BFQ from Paolo.
- minor documentation patches from Randy.
- timeout fix from Tejun.
- Alpha "can't write a char atomically" fix from Mikulas.
- set of NVMe fixes by way of Keith.
- bsg and bsg-lib improvements from Christoph.
- a few sed-opal fixes from Jonas.
- cdrom check-disk-change deadlock fix from Maurizio.
- various little fixes, comment fixes, etc from various folks"
* tag 'for-4.17/block-20180402' of git://git.kernel.dk/linux-block: (139 commits)
blk-mq: Directly schedule q->timeout_work when aborting a request
blktrace: fix comment in blktrace_api.h
lightnvm: remove function name in strings
lightnvm: pblk: remove some unnecessary NULL checks
lightnvm: pblk: don't recover unwritten lines
lightnvm: pblk: implement 2.0 support
lightnvm: pblk: implement get log report chunk
lightnvm: pblk: rename ppaf* to addrf*
lightnvm: pblk: check for supported version
lightnvm: implement get log report chunk helpers
lightnvm: make address conversions depend on generic device
lightnvm: add support for 2.0 address format
lightnvm: normalize geometry nomenclature
lightnvm: complete geo structure with maxoc*
lightnvm: add shorten OCSSD version in geo
lightnvm: add minor version to generic geometry
lightnvm: simplify geometry structure
lightnvm: pblk: refactor init/exit sequences
lightnvm: Avoid validation of default op value
lightnvm: centralize permission check for lightnvm ioctl
...
While UBI and UBIFS seem to work at first sight with MLC NAND, you will
most likely lose all your data upon a power-cut or due to read/write
disturb.
In order to protect users from bad surprises, refuse to attach to MLC
NAND.
Cc: stable@vger.kernel.org
Signed-off-by: Richard Weinberger <richard@nod.at>
Acked-by: Boris Brezillon <boris.brezillon@bootlin.com>
Acked-by: Artem Bityutskiy <dedekind1@gmail.com>
When opening a device with write access, ubiblock_open returns an error
code. Currently, this error code is -EPERM, but this is not the right
value.
The open function for other block devices returns -EROFS when opening
read-only devices with FMODE_WRITE set. When used with dm-verity, the
veritysetup userspace tool is expecting EROFS, and refuses to use the
ubiblock device.
Use -EROFS for ubiblock as well. As a result, veritysetup accepts the
ubiblock device as valid.
Cc: stable@vger.kernel.org
Fixes: 9d54c8a33e (UBI: R/O block driver on top of UBI volumes)
Signed-off-by: Romain Izard <romain.izard.pro@gmail.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
At this point UBI volumes have already been free()'ed and fastmap can no
longer access these data structures.
Reported-by: Martin Townsend <mtownsend1973@gmail.com>
Fixes: 74cdaf2400 ("UBI: Fastmap: Fix memory leaks while closing the WL sub-system")
Cc: stable@vger.kernel.org
Signed-off-by: Richard Weinberger <richard@nod.at>
-----BEGIN PGP SIGNATURE-----
iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAlqKKI0eHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiGRNAH/0v3+nuJ0oiHE1Cl
fH89F9Ma17j8oTo28byRPi7X5XJfJAqANhHa209rguvnC27y3ew/l9k93HoxG12i
ttvyKFDQulQbytfJZXw8lhUyYGXVsTpyNaihPe/NtqPdIxNgfrXsUN9EIEtcnuS2
SiAj51jUySDRNR4ST6TOx4ulDm1zLrmA28WHOBNOTvDi4jTQMt1TsngHfF5AySBB
lD4RTRDDwWDWtdMI7euYSq019TiDXCxmwQ94vZjrqmjmSQcl/yCK/JzEV33SZslg
4WqGIllxONvP/UlwxZLaJ+RrslqxNgDVqQKwJdfYhGaWvpgPFtS1s86zW6IgyXny
02jJfD0=
=DLWn
-----END PGP SIGNATURE-----
Merge tag 'v4.16-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux into mtd/next
Backmerge v4.16-rc2 into mtd/next to resolve a conflict between Linus'
master branch and nand/for-4.17.
* Prepare arrival of the SPI NAND subsystem by implementing a generic
(interface-agnostic) layer to ease manipulation of NAND devices
* Move onenand code base to the drivers/mtd/nand/ dir
* Rework timing mode selection
* Provide a generic way for NAND chip drivers to flag a specific
GET/SET FEATURE operation as supported/unsupported
* Stop embedding ONFI/JEDEC param page in nand_chip
Driver changes:
* Rework/cleanup of the mxc driver
* Various cleanups in the vf610 driver
* Migrate the fsmc and vf610 to ->exec_op()
* Get rid of the pxa driver (replaced by marvell_nand)
* Support ->setup_data_interface() in the GPMI driver
* Fix probe error path in several drivers
* Remove support for unused hw_syndrome mode in sunxi_nand
* Various minor improvements
-----BEGIN PGP SIGNATURE-----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=uvio
-----END PGP SIGNATURE-----
Merge tag 'nand/for-4.17' of git://git.infradead.org/linux-mtd into mtd/next
Core changes:
* Prepare arrival of the SPI NAND subsystem by implementing a generic
(interface-agnostic) layer to ease manipulation of NAND devices
* Move onenand code base to the drivers/mtd/nand/ dir
* Rework timing mode selection
* Provide a generic way for NAND chip drivers to flag a specific
GET/SET FEATURE operation as supported/unsupported
* Stop embedding ONFI/JEDEC param page in nand_chip
Driver changes:
* Rework/cleanup of the mxc driver
* Various cleanups in the vf610 driver
* Migrate the fsmc and vf610 to ->exec_op()
* Get rid of the pxa driver (replaced by marvell_nand)
* Support ->setup_data_interface() in the GPMI driver
* Fix probe error path in several drivers
* Remove support for unused hw_syndrome mode in sunxi_nand
* Various minor improvements
to the same QSPI controller
* Remove an unneeded driver.bus assigned in the fsl-qspi driver
-----BEGIN PGP SIGNATURE-----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=Wrxi
-----END PGP SIGNATURE-----
Merge tag 'spi-nor/for-4.17' of git://git.infradead.org/linux-mtd into mtd/next
* Make fsl-quaspi assign different names to MTD devices connected
to the same QSPI controller
* Remove an unneeded driver.bus assigned in the fsl-qspi driver
Currently on a imx6sx-sdb board, which has two SPI NOR chips connected
to QSPI2 the following output from /proc/mtd is seen:
dev: size erasesize name
mtd0: 01000000 00010000 "21e4000.qspi"
mtd1: 01000000 00010000 "21e4000.qspi"
Attempts to partition them on the kernel command line result in both
chips with identical (and identically named) partitions, which is
an inconvenient behavior.
Assign a different mtd->name for each mtd device to avoid this problem.
After this change the output from /proc/mtd becomes:
dev: size erasesize name
mtd0: 01000000 00010000 "21e4000.qspi-0"
mtd1: 01000000 00010000 "21e4000.qspi-1"
In order to keep mtdparts compatibility keep the mtd->name
unchanged when a single SPI NOR is present.
Reported-by: David Wolfe <david.wolfe@nxp.com>
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Han Xu <han.xu@nxp.com>
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@wedev4u.fr>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
In core.c, some function descriptions do not match function
definitions. Just fix these mismatches.
Signed-off-by: Xiaolei Li <xiaolei.li@mediatek.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
It turns out that the loop where we read manufacturer
jedec_read_mfd() can under some circumstances get a
CFI_MFR_CONTINUATION repeatedly, making the loop go
over all banks and eventually hit the end of the
map and crash because of an access violation:
Unable to handle kernel paging request at virtual address c4980000
pgd = (ptrval)
[c4980000] *pgd=03808811, *pte=00000000, *ppte=00000000
Internal error: Oops: 7 [#1] PREEMPT ARM
CPU: 0 PID: 1 Comm: swapper Not tainted 4.16.0-rc1+ #150
Hardware name: Gemini (Device Tree)
PC is at jedec_probe_chip+0x6ec/0xcd0
LR is at 0x4
pc : [<c03a2bf4>] lr : [<00000004>] psr: 60000013
sp : c382dd18 ip : 0000ffff fp : 00000000
r10: c0626388 r9 : 00020000 r8 : c0626340
r7 : 00000000 r6 : 00000001 r5 : c3a71afc r4 : c382dd70
r3 : 00000001 r2 : c4900000 r1 : 00000002 r0 : 00080000
Flags: nZCv IRQs on FIQs on Mode SVC_32 ISA ARM Segment none
Control: 0000397f Table: 00004000 DAC: 00000053
Process swapper (pid: 1, stack limit = 0x(ptrval))
Fix this by breaking the loop with a return 0 if
the offset exceeds the map size.
Fixes: 5c9c11e1c4 ("[MTD] [NOR] Add support for flash chips with ID in bank other than 0")
Cc: <stable@vger.kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
get_sectorsize() was not using the appropriate macro to extract the
ECC sector size from the config cache, which led to buggy ECC when
using 1024 byte sectors.
Fixes: f88fc122cc ("mtd: nand: Cleanup/rework the atmel_nand driver")
Cc: <stable@vger.kernel.org>
Reported-by: Olivier Schonken <olivier.schonken@gmail.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Reviewed-by: Richard Weinberger <richard@nod.at>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Tested-by: Olivier Schonken <olivier.schonken@gmail.com>
platform_driver_register() takes care of assigning driver->bus
to &platform_bus_type, no need to explicitly assign it in the driver.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Acked-by: Han Xu <han.xu@nxp.com>
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@wedev4u.fr>
The core clock field was badly named ->ecc_clk which might lead to some
confusion. Rename it ->core_clk.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Acked-by: Miquel Raynal <miquel.raynal@bootlin.com>
Prepare the migration of the lpc32xx_slc driver to use nand_scan() by
cleaning the error path in the probe function.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
An error after nand_scan_tail() should trigger a nand_cleanup().
The helper mtd_device_parse_register() returns an error code that should
be checked and nand_cleanup() called accordingly.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
An error after nand_scan_tail() should trigger a nand_cleanup().
The helper mtd_device_parse_register() returns an error code that should
be checked and nand_cleanup() called accordingly.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
An error after nand_scan_tail() should trigger a nand_cleanup().
The helper mtd_device_parse_register() returns an error code that should
be checked and nand_cleanup() called accordingly.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
An error after nand_scan_tail() should trigger a nand_cleanup().
The helper mtd_device_parse_register() returns an error code that should
be checked and nand_cleanup() called accordingly.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
An error after nand_scan_tail() should trigger a nand_cleanup().
The helper mtd_device_register() returns an error code that should
be checked and nand_cleanup() called accordingly.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
An error after nand_scan_tail() should trigger a nand_cleanup().
The helper mtd_device_register() returns an error code that should
be checked and nand_cleanup() called accordingly.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
An error after nand_scan_tail() should trigger a nand_cleanup().
The helper mtd_device_parse_register() returns an error code that should
be checked and nand_cleanup() called accordingly.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
An error after nand_scan_tail() should trigger a nand_cleanup().
The helper mtd_device_register() returns an error code that should
be checked and nand_cleanup() called accordingly.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
This mode is not used by any existing setup and should not be used
because it overwrites the BBMs. Let's just remove it before someone
starts using it.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Tested-by: Miquel Raynal <miquel.raynal@bootlin.com>
On Armada 7K/8K we need to explicitly enable the register clock. This
clock is optional because not all the SoCs using this IP need it but at
least for Armada 7K/8K it is actually mandatory.
The binding documentation is updated accordingly.
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
The kernel.h macro DIV_ROUND_UP performs the computation
(((n) + (d) - 1) / (d)) but is perhaps more readable.
Signed-off-by: Arushi Singhal <arushisinghal19971997@gmail.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
In mtdcore.c, some function descriptions do not match function
definitions. Just fix these mismatches.
Signed-off-by: Xiaolei Li <xiaolei.li@mediatek.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
It is not necessary for all device's maps to be CFI_HOST_ENDIAN.
Maps device can be Big endian or little endian.
Currently it is being taken care using CONFIG_MTD_CFI_LE_BYTE_SWAP or
CONFIG_MTD_CFI_BE_BYTE_SWAP i.e. compile time.
Now update struct map_info's swap field based on device characteristics
defined in device tree.
Signed-off-by: Jagdish Gediya <jagdish.gediya@nxp.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
In the commit 2c77c57d22 ("mtd: move code adding master MTD out of
mtd_add_device_partitions()") behavior of mtd_device_parse_register()
has very slightly changed. It's a pretty non-significant order change
to match updated function behavior.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Reviewed-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
This adds the JEDEC IDs for Eon EN29LV400A variants
EN29LV400AB and EN29LV400AT. This chip is found in the
D-Link DNS-313.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
This allows using this parser with any flash driver that takes care of
setting of_node (using mtd_set_of_node helper) correctly. Up to now
support for "fixed-partitions" DT compatibility string was working only
with flash drivers that were specifying "ofpart" (manually or by letting
mtd use the default set of parsers).
This matches existing bindings documentation.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Reviewed-by: Brian Norris <computersforpeace@gmail.com>
Tested-by: Brian Norris <computersforpeace@gmail.com>
Reviewed-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Type "ofpart" means that OF should be used to get partitioning info and
this driver supports "fixed-partitions" binding only. Renaming it should
lead to less confusion especially when parsers for new compatibility
strings start to appear.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Reviewed-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
In order to properly support compatibility strings as described in the
bindings/mtd/partition.txt "ofpart" type should be treated as an
indication for looking into OF. MTD should check "compatible" property
and search for a matching parser rather than blindly trying the one
supporting "fixed-partitions".
It also means that existing "fixed-partitions" parser should get renamed
to use a more meaningful name.
This commit achievies that aim by introducing a new mtd_part_of_parse().
It works by looking for a matching parser for every string in the
"compatibility" property (starting with the most specific one).
Please note that driver-specified parsers still take a precedence. It's
assumed that driver providing a parser type has a good reason for that
(e.g. having platform data with device-specific info). Also doing
otherwise could break existing setups. The same applies to using default
parsers (including "cmdlinepart") as some overwrite DT data with cmdline
argument.
Partition parsers can now provide an of_match_table to enable
flash<-->parser matching via device tree as documented in the
mtd/partition.txt.
This support is currently limited to built-in parsers as it uses
request_module() and friends. This should be sufficient for most cases
though as compiling parsers as modules isn't a common choice.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Tested-by: Peter Rosin <peda@axentia.se>
Reviewed-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Due to missing information in Hardware manual, current
implementation doesn't read ECCSTAT0 and ECCSTAT1 registers
for IFC 2.0.
Add support to read ECCSTAT0 and ECCSTAT1 registers during
ecccheck for IFC 2.0.
Fixes: 656441478e ("mtd: nand: ifc: Fix location of eccstat registers for IFC V1.0")
Cc: stable@vger.kernel.org # v3.18+
Signed-off-by: Jagdish Gediya <jagdish.gediya@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Number of ECC status registers i.e. (ECCSTATx) has been increased in IFC
version 2.0.0 due to increase in SRAM size. This is causing eccstat
array to over flow.
So, replace eccstat array with u32 variable to make it fail-safe and
independent of number of ECC status registers or SRAM size.
Fixes: bccb06c353 ("mtd: nand: ifc: update bufnum mask for ver >= 2.0.0")
Cc: stable@vger.kernel.org # 3.18+
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Signed-off-by: Jagdish Gediya <jagdish.gediya@nxp.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
As per the IFC hardware manual, Most significant 2 bytes in
nand_fsr register are the outcome of NAND READ STATUS command.
So status value need to be shifted and aligned as per the nand
framework requirement.
Fixes: 82771882d9 ("NAND Machine support for Integrated Flash Controller")
Cc: stable@vger.kernel.org # v3.18+
Signed-off-by: Jagdish Gediya <jagdish.gediya@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
The blackfin architecture is getting removed, so this driver
has become obsolete.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
When there is only a single erase block, the cross erase test
does not report sensible errors. Warn in case there is only
a single erase block instead of executing the test.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Use %*ph format to print small buffer as hex string.
Suggested-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Antonio Cardace <anto.cardace@gmail.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
MTD users are no longer checking erase_info->state to determine if the
erase operation failed or succeeded. Moreover, mtd_erase_callback() is
now a NOP.
We can safely get rid of all mtd_erase_callback() calls and all
erase_info->state assignments. While at it, get rid of the
erase_info->state field, all MTD_ERASE_XXX definitions and the
mtd_erase_callback() function.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Reviewed-by: Richard Weinberger <richard@nod.at>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Bert Kenward <bkenward@solarflare.com>
---
Changes in v2:
- Address a few coding style issues (reported by Miquel)
- Remove comments that are no longer valid (reported by Miquel)
GPMI driver timings derivation looks very empirical and does not use
the known timings that the core wants to use with the NAND chip, by
using local defined constants that have no special meaning from the
outside world.
Simplify the way all of this is computed and use the NAND core's SDR
timings.
Integrity of the reads/writes has been checked with nandbiterrs, speed
improvements with flash_speed on a Freescale i.MX6 DualLite/Solo SABRE
Automotive Board. Measures are below, variations of less than 150kiB/s
between tests are common and then not significant. Speeds using mode 5
are the same, while speeds using mode 0 are quite improved (+40/50%
from non-optimal computation).
Forcing timings mode 0:
=======================
Before this patch:
------------------
eraseblock write speed is 2298 KiB/s
eraseblock read speed is 3636 KiB/s
page write speed is 2136 KiB/s
page read speed is 3316 KiB/s
2 page write speed is 2199 KiB/s
2 page read speed is 3468 KiB/s
After this patch:
-----------------
eraseblock write speed is 3232 KiB/s
eraseblock read speed is 5663 KiB/s
page write speed is 2915 KiB/s
page read speed is 4904 KiB/s
2 page write speed is 3084 KiB/s
2 page read speed is 5267 KiB/s
Forcing timings mode 5:
=======================
Before this patch:
------------------
eraseblock write speed is 4338 KiB/s
eraseblock read speed is 14883 KiB/s
page write speed is 3786 KiB/s
page read speed is 12800 KiB/s
2 page write speed is 4076 KiB/s
2 page read speed is 14065 KiB/s
After this patch:
-----------------
eraseblock write speed is 4309 KiB/s
eraseblock read speed is 14712 KiB/s
page write speed is 3764 KiB/s
page read speed is 12673 KiB/s
2 page write speed is 4076 KiB/s
2 page read speed is 14065 KiB/s
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Until now the GPMI driver had its own timings logic while the core
already handles that and request the NAND controller drivers to support
the ->setup_data_interface() hook. Implement that hook by reusing the
already existing function. No real glue is necessary between core timing
delays and GPMI registers because the driver already translates the
ONFI timing modes into register values.
Make use of the core's tREA, tRLOH and tRHOH values that allow computing
more precise timings for mode [0-3] and get significantly better values
(+20% with an i.MX6 Sabre Auto board). Otherwise use the existing logic.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Tested-by: Han Xu <han.xu@nxp.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
The NAND chip parameter page is statically allocated within the
nand_chip structure, which reserves a lot of space. Even not ONFI nor
JEDEC chips have it embedded. Also, only a few parameters are actually
read from the parameter page after the detection.
Now that there is a small nand_parameters structure that hold all needed
ONFI parameters, remove the ONFI page from the nand_chip structure by
just allocating it during the identification phase and removing it right
after.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
The NAND chip parameter page is statically allocated within the
nand_chip structure, which reserves a lot of space. Even not ONFI nor
JEDEC chips have it embedded. Also, only a few parameters are actually
read from the parameter page after the detection.
Now that there is a small nand_parameters structure that can held
generic parameters, remove the JEDEC page from the nand_chip structure
by just allocating it during the identification phase and removing it
right after.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
The MX30LF2G18AC chip declares in its parameter page supporting
SET/GET_FEATURES but when it comes to timings, experience shows that it
is not the case.
Unflag this feature for this particular chip in the nand_parameters
structure to avoid unnecessary errors and downturns.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
If SET/GET_FEATURES is available (from the parameter page), use a
bitmap to declare what feature is actually supported.
Initialize the bitmap in the core to support timing changes (only
feature used by the core), also add support for Micron specific features
used in Micron initialization code (in the init routine).
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
The NAND chip parameter page is statically allocated within the
nand_chip structure, which reserves a lot of space. Even not ONFI nor
JEDEC chips have it embedded. Also, only a few parameters are actually
read from the parameter page after the detection.
ONFI-related parameters that will be used outside from the
identification function are stored in a separate onfi_parameters
structure embedded in nand_parameters, this small structure that
already hold generic parameters.
For now, the onfi_parameters structure is allocated statically. However,
after some deep rework in the NAND framework, it will be possible to do
dynamic allocations from the NAND identification phase, and this
strcuture will then be dynamically allocated when needed.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
The NAND chip parameter page is statically allocated within the
nand_chip structure, which reserves a lot of space. Even not ONFI nor
JEDEC chips have it embedded. Also, only a few parameters are actually
read from the parameter page after the detection.
To prepare to the removal of such huge structure, a small NAND parameter
structure is allocated statically and contains only very few members
that are generic to all chips and actually used elsewhere in the code.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Linus Torvalds
Richard Weinberger
Romain Izard
Boris Brezillon
Fabio Estevam
Xiaolei Li
Linus Walleij
Miquel Raynal
Gregory CLEMENT
Arushi Singhal
Prabhakar Kushwaha
Rafał Miłecki
Jagdish Gediya
Arnd Bergmann
Stefan Agner
Antonio Cardace