* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next-2.6: (1674 commits)
qlcnic: adding co maintainer
ixgbe: add support for active DA cables
ixgbe: dcb, do not tag tc_prio_control frames
ixgbe: fix ixgbe_tx_is_paused logic
ixgbe: always enable vlan strip/insert when DCB is enabled
ixgbe: remove some redundant code in setting FCoE FIP filter
ixgbe: fix wrong offset to fc_frame_header in ixgbe_fcoe_ddp
ixgbe: fix header len when unsplit packet overflows to data buffer
ipv6: Never schedule DAD timer on dead address
ipv6: Use POSTDAD state
ipv6: Use state_lock to protect ifa state
ipv6: Replace inet6_ifaddr->dead with state
cxgb4: notify upper drivers if the device is already up when they load
cxgb4: keep interrupts available when the ports are brought down
cxgb4: fix initial addition of MAC address
cnic: Return SPQ credit to bnx2x after ring setup and shutdown.
cnic: Convert cnic_local_flags to atomic ops.
can: Fix SJA1000 command register writes on SMP systems
bridge: fix build for CONFIG_SYSFS disabled
ARCNET: Limit com20020 PCI ID matches for SOHARD cards
...
Fix up various conflicts with pcmcia tree drivers/net/
{pcmcia/3c589_cs.c, wireless/orinoco/orinoco_cs.c and
wireless/orinoco/spectrum_cs.c} and feature removal
(Documentation/feature-removal-schedule.txt).
Also fix a non-content conflict due to pm_qos_requirement getting
renamed in the PM tree (now pm_qos_request) in net/mac80211/scan.c
Now that the rpc.gssd daemon can explicitly tell us that the key expired,
we should cache that information to avoid spamming gssd.
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Again, we can deadlock if the memory reclaim triggers a writeback that
requires a rpcsec_gss credential lookup.
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Add necessary changes to add kernel support for the rc4-hmac Kerberos
encryption type used by Microsoft and described in rfc4757.
Signed-off-by: Kevin Coffman <kwc@citi.umich.edu>
Signed-off-by: Steve Dickson <steved@redhat.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
All encryption types use a confounder at the beginning of the
wrap token. In all encryption types except arcfour-hmac, the
confounder is the same as the blocksize. arcfour-hmac has a
blocksize of one, but uses an eight byte confounder.
Add an entry to the crypto framework definitions for the
confounder length and change the wrap/unwrap code to use
the confounder length rather than assuming it is always
the blocksize.
Signed-off-by: Kevin Coffman <kwc@citi.umich.edu>
Signed-off-by: Steve Dickson <steved@redhat.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
For the arcfour-hmac support, the make_seq_num and get_seq_num
functions need access to the kerberos context structure.
This will be used in a later patch.
Signed-off-by: Kevin Coffman <kwc@citi.umich.edu>
Signed-off-by: Steve Dickson <steved@redhat.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
This is needed for deriving arcfour-hmac keys "on the fly"
using the sequence number or checksu
Signed-off-by: Kevin Coffman <kwc@citi.umich.edu>
Signed-off-by: Steve Dickson <steved@redhat.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
For arcfour-hmac support, the make_checksum function needs a usage
field to correctly calculate the checksum differently for MIC and
WRAP tokens.
Signed-off-by: Kevin Coffman <kwc@citi.umich.edu>
Signed-off-by: Steve Dickson <steved@redhat.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Add the remaining pieces to enable support for Kerberos AES
encryption types.
Signed-off-by: Kevin Coffman <kwc@citi.umich.edu>
Signed-off-by: Steve Dickson <steved@redhat.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
This is a step toward support for AES encryption types which are
required to use the new token formats defined in rfc4121.
Signed-off-by: Kevin Coffman <kwc@citi.umich.edu>
[SteveD: Fixed a typo in gss_verify_mic_v2()]
Signed-off-by: Steve Dickson <steved@redhat.com>
[Trond: Got rid of the TEST_ROTATE/TEST_EXTRA_COUNT crap]
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Add the final pieces to support the triple-des encryption type.
Signed-off-by: Kevin Coffman <kwc@citi.umich.edu>
Signed-off-by: Steve Dickson <steved@redhat.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
The text based upcall now indicates which Kerberos encryption types are
supported by the kernel rpcsecgss code. This is used by gssd to
determine which encryption types it should attempt to negotiate
when creating a context with a server.
The server principal's database and keytab encryption types are
what limits what it should negotiate. Therefore, its keytab
should be created with only the enctypes listed by this file.
Currently we support des-cbc-crc, des-cbc-md4 and des-cbc-md5
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
For encryption types other than DES, gssd sends down context information
in a new format. This new format includes the information needed to
support the new Kerberos GSS-API tokens defined in rfc4121.
Signed-off-by: Kevin Coffman <kwc@citi.umich.edu>
Signed-off-by: Steve Dickson <steved@redhat.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Import the code to derive Kerberos keys from a base key into the
kernel. This will allow us to change the format of the context
information sent down from gssd to include only a single key.
Signed-off-by: Kevin Coffman <kwc@citi.umich.edu>
Signed-off-by: Steve Dickson <steved@redhat.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Encryption types besides DES may use a keyed checksum (hmac).
Modify the make_checksum() function to allow for a key
and take care of enctype-specific processing such as truncating
the resulting hash.
Signed-off-by: Kevin Coffman <kwc@citi.umich.edu>
Signed-off-by: Steve Dickson <steved@redhat.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Add enctype framework and change functions to use the generic
values from it rather than the values hard-coded for des.
Signed-off-by: Kevin Coffman <kwc@citi.umich.edu>
Signed-off-by: Steve Dickson <steved@redhat.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Prepare for new context format by splitting out the old "v1"
context processing function
Signed-off-by: Kevin Coffman <kwc@citi.umich.edu>
Signed-off-by: Steve Dickson <steved@redhat.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Add encryption type to the krb5 context structure and use it to switch
to the correct functions depending on the encryption type.
Signed-off-by: Kevin Coffman <kwc@citi.umich.edu>
Signed-off-by: Steve Dickson <steved@redhat.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Make the client and server code consistent regarding the extra buffer
space made available for the auth code when wrapping data.
Add some comments/documentation about the available buffer space
in the xdr_buf head and tail when gss_wrap is called.
Add a compile-time check to make sure we are not exceeding the available
buffer space.
Add a central function to shift head data.
Signed-off-by: Kevin Coffman <kwc@citi.umich.edu>
Signed-off-by: Steve Dickson <steved@redhat.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
percpu.h is included by sched.h and module.h and thus ends up being
included when building most .c files. percpu.h includes slab.h which
in turn includes gfp.h making everything defined by the two files
universally available and complicating inclusion dependencies.
percpu.h -> slab.h dependency is about to be removed. Prepare for
this change by updating users of gfp and slab facilities include those
headers directly instead of assuming availability. As this conversion
needs to touch large number of source files, the following script is
used as the basis of conversion.
http://userweb.kernel.org/~tj/misc/slabh-sweep.py
The script does the followings.
* Scan files for gfp and slab usages and update includes such that
only the necessary includes are there. ie. if only gfp is used,
gfp.h, if slab is used, slab.h.
* When the script inserts a new include, it looks at the include
blocks and try to put the new include such that its order conforms
to its surrounding. It's put in the include block which contains
core kernel includes, in the same order that the rest are ordered -
alphabetical, Christmas tree, rev-Xmas-tree or at the end if there
doesn't seem to be any matching order.
* If the script can't find a place to put a new include (mostly
because the file doesn't have fitting include block), it prints out
an error message indicating which .h file needs to be added to the
file.
The conversion was done in the following steps.
1. The initial automatic conversion of all .c files updated slightly
over 4000 files, deleting around 700 includes and adding ~480 gfp.h
and ~3000 slab.h inclusions. The script emitted errors for ~400
files.
2. Each error was manually checked. Some didn't need the inclusion,
some needed manual addition while adding it to implementation .h or
embedding .c file was more appropriate for others. This step added
inclusions to around 150 files.
3. The script was run again and the output was compared to the edits
from #2 to make sure no file was left behind.
4. Several build tests were done and a couple of problems were fixed.
e.g. lib/decompress_*.c used malloc/free() wrappers around slab
APIs requiring slab.h to be added manually.
5. The script was run on all .h files but without automatically
editing them as sprinkling gfp.h and slab.h inclusions around .h
files could easily lead to inclusion dependency hell. Most gfp.h
inclusion directives were ignored as stuff from gfp.h was usually
wildly available and often used in preprocessor macros. Each
slab.h inclusion directive was examined and added manually as
necessary.
6. percpu.h was updated not to include slab.h.
7. Build test were done on the following configurations and failures
were fixed. CONFIG_GCOV_KERNEL was turned off for all tests (as my
distributed build env didn't work with gcov compiles) and a few
more options had to be turned off depending on archs to make things
build (like ipr on powerpc/64 which failed due to missing writeq).
* x86 and x86_64 UP and SMP allmodconfig and a custom test config.
* powerpc and powerpc64 SMP allmodconfig
* sparc and sparc64 SMP allmodconfig
* ia64 SMP allmodconfig
* s390 SMP allmodconfig
* alpha SMP allmodconfig
* um on x86_64 SMP allmodconfig
8. percpu.h modifications were reverted so that it could be applied as
a separate patch and serve as bisection point.
Given the fact that I had only a couple of failures from tests on step
6, I'm fairly confident about the coverage of this conversion patch.
If there is a breakage, it's likely to be something in one of the arch
headers which should be easily discoverable easily on most builds of
the specific arch.
Signed-off-by: Tejun Heo <tj@kernel.org>
Guess-its-ok-by: Christoph Lameter <cl@linux-foundation.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>
The function alloc_enc_pages() currently fails to release the pointer
rqstp->rq_enc_pages in the error path.
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Acked-by: J. Bruce Fields <bfields@citi.umich.edu>
Cc: stable@kernel.org
The kernel currently ignores any error code sent by gssd and always
considers it to be -EACCES. In order to better handle the situation of
an expired KRB5 TGT, the kernel needs to be able to parse and deal with
the errors that gssd sends. Aside from -EACCES the only error we care
about is -EKEYEXPIRED, which we're using to indicate that the upper
layers should retry the call a little later.
To maintain backward compatibility with older gssd's, any error other
than -EKEYEXPIRED is interpreted as -EACCES.
Signed-off-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Fix auth_gss printk format warning:
net/sunrpc/auth_gss/auth_gss.c:660: warning: format '%ld' expects type 'long int', but argument 3 has type 'ssize_t'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Acked-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
When handling the gssd downcall, the kernel should distinguish between a
successful downcall that contains an error code and a failed downcall
(i.e. where the parsing failed or some other sort of problem occurred).
In the former case, gss_pipe_downcall should be returning the number of
bytes written to the pipe instead of an error. In the event of other
errors, we generally want the initiating task to retry the upcall so
we set msg.errno to -EAGAIN. An unexpected error code here is a bug
however, so BUG() in that case.
Signed-off-by: Jeff Layton <jlayton@redhat.com>
Cc: stable@kernel.org
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
If the context allocation fails, it will return GSS_S_FAILURE, which is
neither a valid error code, nor is it even negative.
Return ENOMEM instead...
Reported-by: Jeff Layton <jlayton@redhat.com>
Cc: stable@kernel.org
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
If the context allocation fails, the function currently returns a random
error code, since the variable 'p' still points to a valid memory location.
Ensure that it returns ENOMEM...
Cc: stable@kernel.org
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
The pointer to struct gss_auth parameter in gss_add_msg is not really needed
after commit 5b7ddd4a. Zap it.
Signed-off-by: Suresh Jayaraman <sjayaraman@suse.de>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Not including net/atm/
Compiled tested x86 allyesconfig only
Added a > 80 column line or two, which I ignored.
Existing checkpatch plaints willfully, cheerfully ignored.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When an RPC message is received with RPCSEC_GSS with an unknown service
(not RPC_GSS_SVC_NONE, RPC_GSS_SVC_INTEGRITY, or RPC_GSS_SVC_PRIVACY),
svcauth_gss_accept() returns AUTH_BADCRED, but svcauth_gss_release()
subsequently drops the response entirely, discarding the error.
Fix that so the AUTH_BADCRED error is returned to the client.
Signed-off-by: Wei Yongjun <yjwei@cn.fujitsu.com>
Signed-off-by: J. Bruce Fields <bfields@citi.umich.edu>
For events that are rare, such as referral DNS lookups, it makes limited
sense to have a daemon constantly listening for upcalls on a channel. An
alternative in those cases might simply be to run the app that fills the
cache using call_usermodehelper_exec() and friends.
The following patch allows the cache_detail to specify alternative upcall
mechanisms for these particular cases.
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
As the module uses rcu_call() we should make sure that all
rcu callback has been completed before removing the code.
Signed-off-by: Jesper Dangaard Brouer <hawk@comx.dk>
Acked-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch extends the new upcall with a "service" field that currently
can have 2 values: "*" or "nfs". These values specify matching rules for
principals in the keytab file. The "*" means that gssd is allowed to use
"root", "nfs", or "host" keytab entries while the other option requires
"nfs".
Restricting gssd to use the "nfs" principal is needed for when the
server performs a callback to the client. The server in this case has
to authenticate itself as an "nfs" principal.
We also need "service" field to distiguish between two client-side cases
both currently using a uid of 0: the case of regular file access by the
root user, and the case of state-management calls (such as setclientid)
which should use a keytab for authentication. (And the upcall should
fail if an appropriate principal can't be found.)
Signed-off: Olga Kornievskaia <aglo@citi.umich.edu>
Signed-off-by: J. Bruce Fields <bfields@citi.umich.edu>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
This patch extends the new upcall by adding a "target" field
communicating who we want to authenticate to (equivalently, the service
principal that we want to acquire a ticket for).
Signed-off: Olga Kornievskaia <aglo@citi.umich.edu>
Signed-off-by: J. Bruce Fields <bfields@citi.umich.edu>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
This patch adds client-side support to allow for callbacks other than
AUTH_SYS.
Signed-off-by: Olga Kornievskaia <aglo@citi.umich.edu>
Signed-off-by: J. Bruce Fields <bfields@citi.umich.edu>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Two principals are involved in krb5 authentication: the target, who we
authenticate *to* (normally the name of the server, like
nfs/server.citi.umich.edu@CITI.UMICH.EDU), and the source, we we
authenticate *as* (normally a user, like bfields@UMICH.EDU)
In the case of NFSv4 callbacks, the target of the callback should be the
source of the client's setclientid call, and the source should be the
nfs server's own principal.
Therefore we allow svcgssd to pass down the name of the principal that
just authenticated, so that on setclientid we can store that principal
name with the new client, to be used later on callbacks.
Signed-off-by: Olga Kornievskaia <aglo@citi.umich.edu>
Signed-off-by: J. Bruce Fields <bfields@citi.umich.edu>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Implement the new upcall. We decide which version of the upcall gssd
will use (new or old), by creating both pipes (the new one named "gssd",
the old one named after the mechanism (e.g., "krb5")), and then waiting
to see which version gssd actually opens.
We don't permit pipes of the two different types to be opened at once.
Signed-off-by: J. Bruce Fields <bfields@citi.umich.edu>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Keep a pointer to the inode that the message is queued on in the struct
gss_upcall_msg. This will be convenient, especially after we have a
choice of two pipes that an upcall could be queued on.
Signed-off-by: J. Bruce Fields <bfields@citi.umich.edu>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Introduce a global variable pipe_version which will eventually be used
to keep track of which version of the upcall gssd is using.
For now, though, it only keeps track of whether any pipe is open or not;
it is negative if not, zero if one is opened. We use this to wait for
the first gssd to open a pipe.
(Minor digression: note this waits only for the very first open of any
pipe, not for the first open of a pipe for a given auth; thus we still
need the RPC_PIPE_WAIT_FOR_OPEN behavior to wait for gssd to open new
pipes that pop up on subsequent mounts.)
Signed-off-by: J. Bruce Fields <bfields@citi.umich.edu>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Keep a count of the number of pipes open plus the number of messages on
a pipe. This count isn't used yet.
Signed-off-by: J. Bruce Fields <bfields@citi.umich.edu>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Linus Torvalds
Trond Myklebust
Kevin Coffman
J. Bruce Fields
David S. Miller
Tejun Heo
Frans Pop
Jeff Layton
Randy Dunlap
Suresh Jayaraman
Roel Kluin
Joe Perches
Wei Yongjun
Jesper Dangaard Brouer
Olga Kornievskaia