Add the PCI IDs directly in the pciidlist array instead of defining an
extra macro. The minor benefit from this is neater diffs when adding to
the end of the list.
v2: drop the "aka" comment (Ville)
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1446053589-21283-1-git-send-email-jani.nikula@intel.com
Mmio register access after dc6/dc5 entry is not allowed when
DC6 power states are enabled according to bspec (bspec-id 0527),
so enabling dc6 as the last call in suspend flow.
Addtional note from Imre:
Currently we keep DC6 enabled during modesets and DPAUX transfers, which
is not allowed according to the specification. This can lead at least to
PLL locking failures, DPAUX timeouts and prevent deeper package power
states (PC9/10). Fix this for now by enabling DC6 only when we know the
above events (modeset, DPAUX) can't happen.
This a temporary solution as some issues are still unsolved as described
in [1] and [2], we'll address those as a follow-up.
[1]
http://lists.freedesktop.org/archives/intel-gfx/2015-October/077669.html
[2]
http://lists.freedesktop.org/archives/intel-gfx/2015-October/077787.html
v1: Initial version.
v2: Based on review comment from Daniel,
- created a seperate patch for csr uninitialization set call.
v3: Rebased on top of latest code.
Cc: Daniel Vetter <daniel.vetter@intel.com>
Cc: Damien Lespiau <damien.lespiau@intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Cc: Sunil Kamath <sunil.kamath@intel.com>
Signed-off-by: Animesh Manna <animesh.manna@intel.com>
Signed-off-by: Vathsala Nagaraju <vathsala.nagaraju@intel.com>
Signed-off-by: Rajneesh Bhardwaj <rajneesh.bhardwaj@intel.com>
Acked-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Add host2guc interface to notify GuC power state changes when
enter or resume from power saving state.
v3: Move intel_guc_suspend to i915_drm_suspend for consistency.
v2: Add GuC suspend/resume to runtime suspend/resume too
v1: Change to a more flexible way when fill host to GuC scratch
data in order to remove hard coding.
Signed-off-by: Alex Dai <yu.dai@intel.com>
Reviewed-by: Sagar Arun Kamble <sagar.a.kamble@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This patch remove the function call to set the firmware
loading status as uninitialized during suspend.
Dmc firmware will restore the firmware in normal suspend. In previous
patch added a check to directly read the hardware status and load
the firmware if got reset during resume from suspend-hibernation.
Cc: Daniel Vetter <daniel.vetter@intel.com>
Signed-off-by: Animesh Manna <animesh.manna@intel.com>
Signed-off-by: Vathsala Nagaraju <vathsala.nagaraju@intel.com>
Reviewed-by: A.Sunil Kamath <sunil.kamath@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Virtualized systems often use a virtual P2X4 south bridge.
Detect this in intel_detect_pch and make a best guess as to which PCH
we should be using.
This was seen on vmware esxi hypervisor. When passing the graphics device
through to a guest, it can not pass through the PCH. Instead it simulates
a P2X4 southbridge.
Signed-off-by: Robert Beckett <robert.beckett@intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Backmerge to catch up with 4.3. slightly more involved conflict in the
irq code, but nothing beyond adjacent changes.
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Pull drm updates from Dave Airlie:
"This is the main pull request for the drm for 4.3. Nouveau is
probably the biggest amount of changes in here, since it missed 4.2.
Highlights below, along with the usual bunch of fixes.
All stuff outside drm should have applicable acks.
Highlights:
- new drivers:
freescale dcu kms driver
- core:
more atomic fixes
disable some dri1 interfaces on kms drivers
drop fb panic handling, this was just getting more broken, as more locking was required.
new core fbdev Kconfig support - instead of each driver enable/disabling it
struct_mutex cleanups
- panel:
more new panels
cleanup Kconfig
- i915:
Skylake support enabled by default
legacy modesetting using atomic infrastructure
Skylake fixes
GEN9 workarounds
- amdgpu:
Fiji support
CGS support for amdgpu
Initial GPU scheduler - off by default
Lots of bug fixes and optimisations.
- radeon:
DP fixes
misc fixes
- amdkfd:
Add Carrizo support for amdkfd using amdgpu.
- nouveau:
long pending cleanup to complete driver,
fully bisectable which makes it larger,
perfmon work
more reclocking improvements
maxwell displayport fixes
- vmwgfx:
new DX device support, supports OpenGL 3.3
screen targets support
- mgag200:
G200eW support
G200e new revision support
- msm:
dragonboard 410c support, msm8x94 support, msm8x74v1 support
yuv format support
dma plane support
mdp5 rotation
initial hdcp
- sti:
atomic support
- exynos:
lots of cleanups
atomic modesetting/pageflipping support
render node support
- tegra:
tegra210 support (dc, dsi, dp/hdmi)
dpms with atomic modesetting support
- atmel:
support for 3 more atmel SoCs
new input formats, PRIME support.
- dwhdmi:
preparing to add audio support
- rockchip:
yuv plane support"
* 'drm-next' of git://people.freedesktop.org/~airlied/linux: (1369 commits)
drm/amdgpu: rename gmc_v8_0_init_compute_vmid
drm/amdgpu: fix vce3 instance handling
drm/amdgpu: remove ib test for the second VCE Ring
drm/amdgpu: properly enable VM fault interrupts
drm/amdgpu: fix warning in scheduler
drm/amdgpu: fix buffer placement under memory pressure
drm/amdgpu/cz: fix cz_dpm_update_low_memory_pstate logic
drm/amdgpu: fix typo in dce11 watermark setup
drm/amdgpu: fix typo in dce10 watermark setup
drm/amdgpu: use top down allocation for non-CPU accessible vram
drm/amdgpu: be explicit about cpu vram access for driver BOs (v2)
drm/amdgpu: set MEC doorbell range for Fiji
drm/amdgpu: implement burst NOP for SDMA
drm/amdgpu: add insert_nop ring func and default implementation
drm/amdgpu: add amdgpu_get_sdma_instance helper function
drm/amdgpu: add AMDGPU_MAX_SDMA_INSTANCES
drm/amdgpu: add burst_nop flag for sdma
drm/amdgpu: add count field for the SDMA NOP packet v2
drm/amdgpu: use PT for VM sync on unmap
drm/amdgpu: make wait_event uninterruptible in push_job
...
Runtime suspends disabled all interrupts, so in order to get them back
fully we need to also do the HPD irq setup on runtime resume. Except
on VLV/CHV where the display interrupt initialization is part of the
display power well powerup.
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Backmerge -fixes since there's more DDI-E related cleanups on top of
the pile of -fixes for skl that just landed for 4.3.
Conflicts:
drivers/gpu/drm/i915/intel_display.c
drivers/gpu/drm/i914/intel_dp.c
drivers/gpu/drm/i915/intel_lrc.c
Conflicts are all fairly harmless adjacent line stuff.
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
The driver doesn't support UMS any more, so set DRIVER_MODESET by default,
remove the legacy s/r callbacks, and rename the s/r functions to make it more clear
they're only in use by switcheroo now.
Also remove an obsolete comment about atomic. Normal updates are supported only
async updates aren't yet.
v2: Don't unconditionally set DRIVER_ATOMIC, we're not yet there.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
commit da2bc1b9db
Author: Imre Deak <imre.deak@intel.com>
Date: Thu Oct 23 19:23:26 2014 +0300
drm/i915: add poweroff_late handler
introduced a regression on old platforms during hibernation. A workaround was
added in
commit ab3be73fa7
Author: Imre Deak <imre.deak@intel.com>
Date: Mon Mar 2 13:04:41 2015 +0200
drm/i915: gen4: work around hang during hibernation
using an explicit blacklist for the GENs/BIOS vendors where the issue was
reported. Later there we had reports of the same failure on platforms not on
this list.
To my best knowledge the correct thing to do is still to put the device to PCI
D3 state during hibernation, see [1] and [2] for the reasons. This also aligns
with our future plans to unify more the runtime and system suspend/resume
paths. Since an exact blacklist seems to be impractical (multiple GENs and
BIOS vendors are affected) apply the workaround on everything pre GEN6.
[1] http://lists.freedesktop.org/archives/intel-gfx/2015-February/060710.html
[2] https://lkml.org/lkml/2015/6/22/274
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=95061
Reported-by: Ilya Tumaykin <itumaykin@gmail.com>
Reported-by: Dirk Griesbach <spamthis@freenet.de>
Reported-by: Pavel Machek <pavel@ucw.cz>
Reported-by: Mikko Rapeli <mikko.rapeli@iki.fi>
Tested-by: Mikko Rapeli <mikko.rapeli@iki.fi>
Reported-by: Paul Bolle <pebolle@tiscali.nl>
CC: stable@vger.kernel.org
Signed-off-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
This partially reverts commit 74c090b1bd.
The DRIVER_ATOMIC cap cannot yet be exported because i915 lacks async
support.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Dear git bisect user,
Even though this is the patch that introduced the WARN() you're
bisecting, please notice that it's very likely that the problem you're
facing was already present before this commit. In other words: this
commit adds code to detect errors and give WARN()s about them, but the
errors were already there.
In order to continue your debug, please use the i915.mmio_debug
option, check the backtraces and try to discover which read or write
operation is causing the error message. Then check if this is
happening because the register does not exist or because its power
well is down when the operation is being done.
On my SKL machine, if I use i915.mmio_debug=999, this patch triggers
42 WARNs just by booting. I didn't investigate them yet. Normal users
are only going to get a single WARN due to the default i915.mmio_debug
setting.
Thank you for your comprehension,
Paulo
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
I was told that the "repurposed D1 definition" is still valid for SKL.
It is BDW that is special due to its hotplug bug, so let's
special-case BDW instead of HSW.
Cc: Kristen Carlson Accardi <kristen@linux.intel.com>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Remove the leftovers, yay!
AGP for i915 kms died long ago with
commit 3bb6ce6686
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Wed Nov 13 22:14:16 2013 +0100
drm/i915: Kill legeacy AGP for gen3 kms
and with ums now gone to there's really no users any more.
Note that device_is_agp is only called when DRIVER_USE_AGP is set and
since we've unconditionally cleared that since a while there are
really no users left for i915_driver_device_is_agp.
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Replace the deprecated atomic_{set,clear}_mask() usage with the now
ubiquous atomic_{or,andnot}() functions.
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Time to light a candle and remove the preliminary_hw_support flag.
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Huzzah! \o/
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Daniel Stone <daniels@collabora.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Instead of all the ad-hoc updating, duplicate the old state first
before reading out the hw state, then restore it.
intel_display_resume is a new function that duplicates the sw state,
then reads out the hw state, and commits the old state.
intel_display_setup_hw_state now only reads out the atomic state.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=90396
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Daniel Stone <daniels@collabora.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
If the user disables the GPU reset using the i915.reset parameter and
one occurs, report that we failed to reset the GPU. If we return early,
as we currently do, then we leave all state intact (with a hung GPU)
and clients block forever waiting for their requests to complete.
Testcase: igt/gem_eio
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
[danvet: Mark i915.reset as an unsafe modoption, as discussed with
Chris.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The module pciid list got lost, but somehow most distros seem to
force-load drm drivers early and no one noticed for a while.
Bug introduced in
commit fd930478fb
Author: Chris Wilson <chris@chris-wilson.co.uk>
Date: Fri Jun 19 20:27:27 2015 +0100
drm/i915: Remove KMS Kconfig option
Reported-by: Tvrtko Ursulin <tvrtko.ursulin@linux.intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@linux.intel.com>
Cc: Damien Lespiau <damien.lespiau@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Since we only support modesetting by default (disabling modesetting on
the command line prevents i915.ko from loading), having a parameter to
disable modesstting by default is superfluous, i.e. saying
CONFIG_DRM_I915_KMS=n is equivalent to CONFIG_DRM_I915=n.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Daniel Veter <daniel.vetter@ffwll.ch>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We have enough generic hotplug functions sprinkled all over i915_irq.c
to warrant moving them to a file of their own. This should further
underline the distinction between generic code in the new file and
platform specific hotplug and irq code that remains in i915_irq.c.
Add new intel_hpd_init_work to keep work functions static, and rename
get_port_from_pin to intel_hpd_pin_to_port while increasing its
visibility, but keep everything else the same.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This reverts commit 490f400db5d886fc28566af69b02f6497f31be4b.
We're not ready yet to make it atomic, we calculate some state in
advance, but without atomic plane support atomic the hw readout will
fail.
It's required to revert this commit to revert the atomic hw
state readout patch.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=90868
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=90861
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Acked-by: Ander Conselvan de Oliveira <conselvan2@gmail.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Calculate all state using a normal transition, but afterwards fudge
crtc->state->active back to its old value. This should still allow
state restore in setup_hw_state to work properly.
Calling intel_set_mode will cause intel_display_set_init_power to be
called, make sure init_power gets set again afterwards.
Changes since v1:
- Fix to compile with v2 of the patch that adds intel_display_suspend.
- Add intel_display_set_init_power.
- Set return value to int to allow error checking.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
This is a function used to disable all crtc's. This makes it clearer
to distinguish between when mode needs to be preserved and when
it can be trashed.
Changes since v1:
- Copy power changes from intel_crtc_control.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
There are plenty of hotplug related fields in struct drm_i915_private
scattered all around. Group them under one hotplug struct. Clean up
naming while at it. No functional changes.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We need to re-init the display hardware when going out of suspend. This
includes:
- Hooking the PCH to the reset logic
- Restoring CDCDLK
- Enabling the DDB power
Among those, only the CDCDLK one is a bit tricky. There's some
complexity in that:
- DPLL0 (which is the source for CDCLK) has two VCOs, each with a set
of supported frequencies. As eDP also uses DPLL0 for its link rate,
once DPLL0 is on, we restrict the possible eDP link rates the chosen
VCO.
- CDCLK also limits the bandwidth available to push pixels.
So, as a first step, this commit restore what the BIOS set, until I can
do more testing.
In case that's of interest for the reviewer, I've unit tested the
function that derives the decimal frequency field:
#include <stdio.h>
#include <stdint.h>
#include <assert.h>
#define ARRAY_SIZE(x) (sizeof(x) / sizeof(*(x)))
static const struct dpll_freq {
unsigned int freq;
unsigned int decimal;
} freqs[] = {
{ .freq = 308570, .decimal = 0b01001100111},
{ .freq = 337500, .decimal = 0b01010100001},
{ .freq = 432000, .decimal = 0b01101011110},
{ .freq = 450000, .decimal = 0b01110000010},
{ .freq = 540000, .decimal = 0b10000110110},
{ .freq = 617140, .decimal = 0b10011010000},
{ .freq = 675000, .decimal = 0b10101000100},
};
static void intbits(unsigned int v)
{
int i;
for(i = 10; i >= 0; i--)
putchar('0' + ((v >> i) & 1));
}
static unsigned int freq_decimal(unsigned int freq /* in kHz */)
{
return (freq - 1000) / 500;
}
static void test_freq(const struct dpll_freq *entry)
{
unsigned int decimal = freq_decimal(entry->freq);
printf("freq: %d, expected: ", entry->freq);
intbits(entry->decimal);
printf(", got: ");
intbits(decimal);
putchar('\n');
assert(decimal == entry->decimal);
}
int main(int argc, char **argv)
{
int i;
for (i = 0; i < ARRAY_SIZE(freqs); i++)
test_freq(&freqs[i]);
return 0;
}
v2:
- Rebase on top of -nightly
- Use (freq - 1000) / 500 for the decimal frequency (Ville)
- Fix setting the enable bit of HSW_NDE_RSTWRN_OPT (Ville)
- Rename skl_display_{resume,suspend} to skl_{init,uninit}_cdclk to
be consistent with the BXT code (Ville)
- Store boot CDCLK in ddi_pll_init (Ville)
- Merge dev_priv's skl_boot_cdclk into cdclk_freq
- Use LCPLL_PLL_LOCK instead of (1 << 30) (Ville)
- Replace various '0' by SKL_DPLL0 to be a bit more explicit that
we're programming DPLL0
- Busy poll the PCU before doing the frequency change. It takes about
3/4 cycles, each separated by 10us, to get the ACK from the CPU
(Ville)
v3:
- Restore dev_priv->skl_boot_cdclk, leaving unification with
dev_priv->cdclk_freq for a later patch (Daniel, Ville)
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The macros we use there are the magic ones that can take either dev or
dev_priv. We'd like to move as much as possible towards dev_priv though.
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Currently bxt_resume_prepare() is only used in the runtime-resume path.
Add it to the full S3/S4 path as well.
v2: Rebase on top of the vlv_resume_prepare() shuffling around
Cc: Imre Deak <imre.deak@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com> (v1)
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJVWh3TAAoJEHm+PkMAQRiG/kwH/2c9irodp2+M9OUnX2bfsBb6
LnChiDpvkF5BB8jhP6d/XmvPp4NJzAbTxByhjdfb2E2HkorCUHCOIn2tI1TE2pUs
2qjkOVH+XCzoV0goGtQjzK1ht8f2IrtlDiEjyRekK5cJHzhggb22QPtWL4npyd0O
reDmG2jsRaF9POr9uLSFEv4CEnkksmRLUU0vuQX0TZeCJ41O7TXrkN/wKrLZ5mj4
IWpqXQaSlrffq/T5HnVbXBxk3/T8QmhrIoppiMpV1mUVj0uTqlFRNi5qwT2Nit1h
FVljWI4+WgOk3bf7fUlp+ahopjkTgu+GuXkiRP/pdgWNQO0cxCWSAzSndAlIIAE=
=uOoJ
-----END PGP SIGNATURE-----
Backmerge v4.1-rc4 into into drm-next
We picked up a silent conflict in amdkfd with drm-fixes and drm-next,
backmerge v4.1-rc5 and fix the conflicts
Signed-off-by: Dave Airlie <airlied@redhat.com>
Conflicts:
drivers/gpu/drm/drm_irq.c
This patch fixes a timing issue that causes a GPU hang when the system
comes out of power saving.
During pm_resume, We are submitting batchbuffers before enabling
Interrupts this is causing us to miss the context switch interrupt,
and in consequence intel_execlists_handle_ctx_events is not triggered.
This patch is based on a patch from Deepak S <deepak.s@intel.com>
from another platform.
The patch fixes an issue introduced by:
commit e7778be1ea
drm/i915: Fix startup failure in LRC mode after recent init changes
The above patch added a call to init_context() to fix an issue introduced
by a previous patch. But, it then opened up a small timing window for the
batches being added by the init_context (basically setting up the context)
to complete before the interrupts have been turned on, thus hanging the
GPU.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=89600
Cc: stable@vger.kernel.org # 4.0+
Signed-off-by: Peter Antoine <peter.antoine@intel.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
[Jani: fixed typo in subject, massaged the comments a bit]
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Looks like it was introduced in:
commit 650ad970a3
Author: Imre Deak <imre.deak@intel.com>
Date: Fri Apr 18 16:35:02 2014 +0300
drm/i915: vlv: factor out vlv_force_gfx_clock and check for pending force-of
but I'm not sure why. It has caused problems for us in the past (see
85250ddff7 "drm/i915/chv: Remove Wait for a previous gfx force-off"
and 8d4eee9cd7 "drm/i915: vlv: increase timeout when forcing on the
GFX clock") and doesn't seem to be required, so let's just drop it.
References: https://bugs.freedesktop.org/show_bug.cgi?id=89611
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Tested-by: Darren Hart <dvhart@linux.intel.com>
Reviewed-by: Deepak S <deepak.s@linux.intel.com>
Cc: stable@vger.kernel.org # c9c52e24194a: drm/i915/chv: Remove Wait ...
Cc: stable@vger.kernel.org
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
[danvet: Repick this commit from
5df0582bf0 becuase Dave Airlie lost it
in his merge commit e1dee1973c74a0408b108d88c57a15be8a2d6d84.]
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Add triggers for DC6 as per details provided in skl_enable_dc6
and skl_disable_dc6 implementations.
Also Call POSTING_READ for every write to a register to ensure
it is written to immediately
v1: Remove POSTING_READ and intel_prepare_ddi calls as they've been added in previous patches.
v2:
1] Remove check for backlight disabled as it should be the case by that time.
2] Mark DC5 as disabled when enabling DC6.
3] Return from DC5-disabling function early if DC5 is already be disabled which can happen
due to DC6-enabling earlier.
3] Ensure CSR firmware is loaded after resume from DC6 as corresponding memory contents won't
be retained after runtime-suspend.
4] Ensure that CSR isn't identified as loaded before CSR-loading program is called during
runtime-resume.
v3: Rebase to latest
Modified as per review comments from Imre and after discussion with Art:
1] DC6 should be preferably enabled when PG2 is disabled by SW as the check for PG1 being
disabled is taken of by HW to enter DC6, and disabled when PG2 is enabled respectively.
This helps save more power, especially in the case when display is disabled but GT is
enabled. Accordingly, replacing DC5 trigger sequence with DC6 for SKL.
2] DC6 could be enabled from intel_runtime_suspend() function, if DC5 is already enabled.
3] Move CSR-load-status setting code from intel_runtime_suspend function to a new function.
v4:
1] Enable/disable DC6 only when toggling the power-well using a newly defined macro ENABLE_DC6.
v5:
1] Load CSR on system resume too as firmware may be lost on system suspend preventing
enabling DC5, DC6.
2] DDI buffers shouldn't be programmed during driver-load/resume as it's already done
during modeset initialization then and also that the encoder list is still uninitialized by
then. Therefore, call intel_prepare_ddi function right after disabling DC6 but outside
skl_disable_dc6 function and not during driver-load/resume.
v6:
1] Rebase to latest.
2] Move SKL_ENABLE_DC6 macro definition from intel_display.c to intel_runtime_pm.c.
v7:
1) Refactored the code for removing the warning got from checkpatch.
2) After adding dmc ver 1.0 support rebased on top of nightly. (Animesh)
v8:
- Reverted the changes done in v7.
- Removed the condition check in skl_prepare_resune(). (Animesh)
Issue: VIZ-2819
Signed-off-by: A.Sunil Kamath <sunil.kamath@intel.com>
Signed-off-by: Suketu Shah <suketu.j.shah@intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Animesh Manna <animesh.manna@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Display Context Save and Restore support is needed for
various SKL Display C states like DC5, DC6.
This implementation is added based on first version of DMC CSR program
that we received from h/w team.
Here we are using request_firmware based design.
Finally this firmware should end up in linux-firmware tree.
For SKL platform its mandatory to ensure that we load this
csr program before enabling DC states like DC5/DC6.
As CSR program gets reset on various conditions, we should ensure
to load it during boot and in future change to be added to load
this system resume sequence too.
v1: Initial relese as RFC patch
v2: Design change as per Daniel, Damien and Shobit's review comments
request firmware method followed.
v3: Some optimization and functional changes.
Pulled register defines into drivers/gpu/drm/i915/i915_reg.h
Used kmemdup to allocate and duplicate firmware content.
Ensured to free allocated buffer.
v4: Modified as per review comments from Satheesh and Daniel
Removed temporary buffer.
Optimized number of writes by replacing I915_WRITE with I915_WRITE64.
v5:
Modified as per review comemnts from Damien.
- Changed name for functions and firmware.
- Introduced HAS_CSR.
- Reverted back previous change and used csr_buf with u8 size.
- Using cpu_to_be64 for endianness change.
Modified as per review comments from Imre.
- Modified registers and macro names to be a bit closer to bspec terminology
and the existing register naming in the driver.
- Early return for non SKL platforms in intel_load_csr_program function.
- Added locking around CSR program load function as it may be called
concurrently during system/runtime resume.
- Releasing the fw before loading the program for consistency
- Handled error path during f/w load.
v6: Modified as per review comments from Imre.
- Corrected out_freecsr sequence.
v7: Modified as per review comments from Imre.
Fail loading fw if fw->size%8!=0.
v8: Rebase to latest.
v9: Rebase on top of -nightly (Damien)
v10: Enabled support for dmc firmware ver 1.0.
According to ver 1.0 in a single binary package all the firmware's that are
required for different stepping's of the product will be stored. The package
contains the css header, followed by the package header and the actual dmc
firmwares. Package header contains the firmware/stepping mapping table and
the corresponding firmware offsets to the individual binaries, within the
package. Each individual program binary contains the header and the payload
sections whose size is specified in the header section. This changes are done
to extract the specific firmaware from the package. (Animesh)
v11: Modified as per review comemnts from Imre.
- Added code comment from bpec for header structure elements.
- Added __packed to avoid structure padding.
- Added helper functions for stepping and substepping info.
- Added code comment for CSR_MAX_FW_SIZE.
- Disabled BXT firmware loading, will be enabled with dmc 1.0 support.
- Changed skl_stepping_info based on bspec, earlier used from config DB.
- Removed duplicate call of cpu_to_be* from intel_csr_load_program function.
- Used cpu_to_be32 instead of cpu_to_be64 as firmware binary in dword aligned.
- Added sanity check for header length.
- Added sanity check for mmio address got from firmware binary.
- kmalloc done separately for dmc header and dmc firmware. (Animesh)
v12: Modified as per review comemnts from Imre.
- Corrected the typo error in skl stepping info structure.
- Added out-of-bound access for skl_stepping_info.
- Sanity check for mmio address modified.
- Sanity check added for stepping and substeppig.
- Modified the intel_dmc_info structure, cache only the required header info. (Animesh)
v13: clarify firmware load error message.
The reason for a firmware loading failure can be obscure if the driver
is built-in. Provide an explanation to the user about the likely reason for
the failure and how to resolve it. (Imre)
v14: Suggested by Jani.
- fix s/I915/CONFIG_DRM_I915/ typo
- add fw_path to the firmware object instead of using a static ptr (Jani)
v15:
1) Changed the firmware name as dmc_gen9.bin, everytime for a new firmware version a symbolic link
with same name will help not to build kernel again.
2) Changes done as per review comments from Imre.
- Error check removed for intel_csr_ucode_init.
- Moved csr-specific data structure to intel_csr.h and optimization done on structure definition.
- fw->data used directly for parsing the header info & memory allocation
only done separately for payload. (Animesh)
v16:
- No need for out_regs label in i915_driver_load(), so removed it.
- Changed the firmware name as skl_dmc_ver1.bin, followed naming convention <platform>_dmc_<api-version>.bin (Animesh)
Issue: VIZ-2569
Signed-off-by: A.Sunil Kamath <sunil.kamath@intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Animesh Manna <animesh.manna@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
drm-intel-next-2015-04-23:
- dither support for ns2501 dvo (Thomas Richter)
- some polish for the gtt code and fixes to finally enable the cmd parser on hsw
- first pile of bxt stage 1 enabling (too many different people to list ...)
- more psr fixes from Rodrigo
- skl rotation support from Chandra
- more atomic work from Ander and Matt
- pile of cleanups and micro-ops for execlist from Chris
drm-intel-next-2015-04-10:
- cdclk handling cleanup and fixes from Ville
- more prep patches for olr removal from John Harrison
- gmbus pin naming rework from Jani (prep for bxt)
- remove ->new_config from Ander (more atomic conversion work)
- rps (boost) tuning and unification with byt/bsw from Chris
- cmd parser batch bool tuning from Chris
- gen8 dynamic pte allocation (Michel Thierry, based on work from Ben Widawsky)
- execlist tuning (not yet all of it) from Chris
- add drm_plane_from_index (Chandra)
- various small things all over
* tag 'drm-intel-next-2015-04-23-fixed' of git://anongit.freedesktop.org/drm-intel: (204 commits)
drm/i915/gtt: Allocate va range only if vma is not bound
drm/i915: Enable cmd parser to do secure batch promotion for aliasing ppgtt
drm/i915: fix intel_prepare_ddi
drm/i915: factor out ddi_get_encoder_port
drm/i915/hdmi: check port in ibx_infoframe_enabled
drm/i915/hdmi: fix vlv infoframe port check
drm/i915: Silence compiler warning in dvo
drm/i915: Update DRIVER_DATE to 20150423
drm/i915: Enable dithering on NatSemi DVO2501 for Fujitsu S6010
rm/i915: Move i915_get_ggtt_vma_pages into ggtt_bind_vma
drm/i915: Don't try to outsmart gcc in i915_gem_gtt.c
drm/i915: Unduplicate i915_ggtt_unbind/bind_vma
drm/i915: Move ppgtt_bind/unbind around
drm/i915: move i915_gem_restore_gtt_mappings around
drm/i915: Fix up the vma aliasing ppgtt binding
drm/i915: Remove misleading comment around bind_to_vm
drm/i915: Don't use atomics for pg_dirty_rings
drm/i915: Don't look at pg_dirty_rings for aliasing ppgtt
drm/i915/skl: Support Y tiling in MMIO flips
drm/i915: Fixup kerneldoc for struct intel_context
...
Conflicts:
drivers/gpu/drm/i915/i915_drv.c
three fixes for i915.
* tag 'drm-intel-next-fixes-2015-04-25' of git://anongit.freedesktop.org/drm-intel:
drm/i915: vlv: fix save/restore of GFX_MAX_REQ_COUNT reg
drm/i915: Workaround to avoid lite restore with HEAD==TAIL
drm/i915: cope with large i2c transfers
Due this typo we don't save/restore the GFX_MAX_REQ_COUNT register across
suspend/resume, so fix this.
This was introduced in
commit ddeea5b0c3
Author: Imre Deak <imre.deak@intel.com>
Date: Mon May 5 15:19:56 2014 +0300
drm/i915: vlv: add runtime PM support
I noticed this only by reading the code. To my knowledge it shouldn't
cause any real problems at the moment, since the power well backing this
register remains on across a runtime s/r. This may change once
system-wide s0ix functionality is enabled in the kernel.
v2:
- resend after a missing git add -u :/
Cc: stable@vger.kernel.org
Signed-off-by: Imre Deak <imre.deak@intel.com>
Tested-By: PRC QA PRTS (Patch Regression Test System Contact: shuang.he@intel.com)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
The merge is clean, but the arm build fails afterwards,
due to API changes in the regulator tree.
I've included the patch into the merge to fix the build.
Signed-off-by: Dave Airlie <airlied@redhat.com>
Add triggers for DC9 as per details provided in bxt_enable_dc9
and bxt_disable_dc9 implementations.
v1:
- Add SKL check in gen9_disable_dc5 as it is possible for DC5
to remain disabled only for SKL.
- Add additional checks for whether DC5 is already disabled during
DC5-disabling only for BXT.
v2:
- rebase to latest.
- Load CSR during DC9 disabling in the beginning before DC9 is
disabled.
- Make gen9_disable_dc5 function non-static as it's being called by
functions in i915_drv.c.
- Enable DC9-related functionality using a macro.
v3: (imre)
- remove BXT_ENABLE_DC9, we want DC9 always, and it's only valid on BXT
- remove DC5 disabling and CSR FW loaded check, these are nop atm
- squash in Vandana's "Do ddi_phy_init always" patch
v4:
- add TODO to re-enable DC5 during resume if CSR FW is available (sagar)
Signed-off-by: Suketu Shah <suketu.j.shah@intel.com>
Signed-off-by: A.Sunil Kamath <sunil.kamath@intel.com> (v2)
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Sagar Kamble <sagar.a.kamble@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Separate topic branch for bxt didn't work out since we needed to
refactor the gmbus code a bit to make it look decent. So backmerge.
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
v2: Switch to info->ring_mask and add VEBOX support.
v3: Fold in update from Damien.
v4: Add GEN_DEFAULT_PIPEOFFSETS and IVB_CURSOR_OFFSETS
v5: set no-LLC (imre)
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com> (v1,v4)
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch> (v4)
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Antti Koskipää <antti.koskipaa@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Looks like it was introduced in:
commit 650ad970a3
Author: Imre Deak <imre.deak@intel.com>
Date: Fri Apr 18 16:35:02 2014 +0300
drm/i915: vlv: factor out vlv_force_gfx_clock and check for pending force-of
but I'm not sure why. It has caused problems for us in the past (see
85250ddff7 "drm/i915/chv: Remove Wait for a previous gfx force-off"
and 8d4eee9cd7 "drm/i915: vlv: increase timeout when forcing on the
GFX clock") and doesn't seem to be required, so let's just drop it.
References: https://bugs.freedesktop.org/show_bug.cgi?id=89611
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Tested-by: Darren Hart <dvhart@linux.intel.com>
Reviewed-by: Deepak S <deepak.s@linux.intel.com>
Cc: stable@vger.kernel.org # c9c52e24194a: drm/i915/chv: Remove Wait ...
Cc: stable@vger.kernel.org
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
On CHV, PUNIT team confirmed that 'VLV_GFX_CLK_STATUS_BIT' is not a
sticky bit and it will always be set. So ignore Check for previous
Gfx force off during suspend and allow the force clk as part S0ix
Sequence
Signed-off-by: Deepak S <deepak.s@linux.intel.com>
Cc: stable@vger.kernel.org
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Some BIOSes (e.g. the one on the Minnowboard) don't save/restore this
reg. If it's unlocked, we can just restore the previous value, and if
it's locked (in case the BIOS re-programmed it for us) the write will be
ignored and we'll still have "did it move" sanity check in the PM code to
warn us if something is still amiss.
References: https://bugs.freedesktop.org/show_bug.cgi?id=89611
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Tested-by: Darren Hart <dvhart@linux.intel.com>
Cc: stable@vger.kernel.org
Reviewed-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Deepak S <deepak.s@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
On CHV, PUNIT team confirmed that 'VLV_GFX_CLK_STATUS_BIT' is not a
sticky bit and it will always be set. So ignore Check for previous
Gfx force off during suspend and allow the force clk as part S0ix
Sequence
Signed-off-by: Deepak S <deepak.s@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
CHV should be in a good enough shape now, so let's drop the
.is_preliminary flag.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
With the two-step reset counter increments which braket the actual
reset code and the subsequent wake-up we're guaranteeing that all the
lockless waiters _will_ be woken up. And since we unconditionally bail
out of waits with -EAGAIN (or -EIO) in that case there is not risk of
lost interrupt enabling bits when the lockless wait code races against
a gpu reset.
Let's remove this FIXME as resolved then.
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJU/NacAAoJEHm+PkMAQRiGdUcIAJU5dHclwd9HRc7LX5iOwYN6
mN0aCsYjMD8Pjx2VcPCgJvkIoESQO5pkwYpFFWCwILup1bVEidqXfr8EPOdThzdh
kcaT0FwUvd19K+0jcKVNCX1RjKBtlUfUKONk6sS2x4RrYZpv0Ur8Gh+yXV8iMWtf
fAusNEYlxQJvEz5+NSKw86EZTr4VVcykKLNvj+/t/JrXEuue7IG8EyoAO/nLmNd2
V/TUKKttqpE6aUVBiBDmcMQl2SUVAfp5e+KJAHmizdDpSE80nU59UC1uyV8VCYdM
qwHXgttLhhKr8jBPOkvUxl4aSXW7S0QWO8TrMpNdEOeB3ZB8AKsiIuhe1JrK0ro=
=Xkue
-----END PGP SIGNATURE-----
Merge tag 'v4.0-rc3' into drm-next
Linux 4.0-rc3 backmerge to fix two i915 conflicts, and get
some mainline bug fixes needed for my testing box
Conflicts:
drivers/gpu/drm/i915/i915_drv.h
drivers/gpu/drm/i915/intel_display.c
- Y tiling support for scanout from Tvrtko&Damien
- Remove more UMS support
- some small prep patches for OLR removal from John Harrison
- first few patches for dynamic pagetable allocation from Ben Widawsky, rebased
by tons of other people
- DRRS support patches (Sonika&Vandana)
- fbc patches from Paulo
- make sure our vblank callbacks aren't called when the pipes are off
- various patches all over
* tag 'drm-intel-next-2015-02-27' of git://anongit.freedesktop.org/drm-intel: (61 commits)
drm/i915: Update DRIVER_DATE to 20150227
drm/i915: Clarify obj->map_and_fenceable
drm/i915/skl: Allow Y (and Yf) frame buffer creation
drm/i915/skl: Update watermarks for Y tiling
drm/i915/skl: Updated watermark programming
drm/i915/skl: Adjust get_plane_config() to support Yb/Yf tiling
drm/i915/skl: Teach pin_and_fence_fb_obj() about Y tiling constraints
drm/i915/skl: Adjust intel_fb_align_height() for Yb/Yf tiling
drm/i915/skl: Allow scanning out Y and Yf fbs
drm/i915/skl: Add new displayable tiling formats
drm/i915: Remove DRIVER_MODESET checks from modeset code
drm/i915: Remove regfile code&data for UMS suspend/resume
drm/i915: Remove DRIVER_MODESET checks from gem code
drm/i915: Remove DRIVER_MODESET checks in the gpu reset code
drm/i915: Remove DRIVER_MODESET checks from suspend/resume code
drm/i915: Remove DRIVER_MODESET checks in load/unload/close code
drm/i915: fix a printk format
drm/i915: Add media rc6 residency file to sysfs
drm/i915: Add missing description to parameter in alloc_pt_range
drm/i915: Removed the read of RP_STATE_CAP from sysfs/debugfs functions
...
- use the atomic helpers for plane_upate/disable hooks (Matt Roper)
- refactor the initial plane config code (Damien)
- ppgtt prep patches for dynamic pagetable alloc (Ben Widawsky, reworked and
rebased by a lot of other people)
- framebuffer modifier support from Tvrtko Ursulin, drm core code from Rob Clark
- piles of workaround patches for skl from Damien and Nick Hoath
- vGPU support for xengt on the client side (Yu Zhang)
- and the usual smaller things all over
* tag 'drm-intel-next-2015-02-14' of git://anongit.freedesktop.org/drm-intel: (88 commits)
drm/i915: Update DRIVER_DATE to 20150214
drm/i915: Remove references to previously removed UMS config option
drm/i915/skl: Use a LRI for WaDisableDgMirrorFixInHalfSliceChicken5
drm/i915/skl: Fix always true comparison in a revision id check
drm/i915/skl: Implement WaEnableLbsSlaRetryTimerDecrement
drm/i915/skl: Implement WaSetDisablePixMaskCammingAndRhwoInCommonSliceChicken
drm/i915: Add process identifier to requests
drm/i915/skl: Implement WaBarrierPerformanceFixDisable
drm/i915/skl: Implement WaCcsTlbPrefetchDisable:skl
drm/i915/skl: Implement WaDisableChickenBitTSGBarrierAckForFFSliceCS
drm/i915/skl: Implement WaDisableHDCInvalidation
drm/i915/skl: Implement WaDisableLSQCROPERFforOCL
drm/i915/skl: Implement WaDisablePartialResolveInVc
drm/i915/skl: Introduce a SKL specific init_workarounds()
drm/i915/skl: Document that we implement WaRsClearFWBitsAtReset
drm/i915/skl: Implement WaSetGAPSunitClckGateDisable
drm/i915/skl: Make the init clock gating function skylake specific
drm/i915/skl: Provide a gen9 specific init_render_ring()
drm/i915/skl: Document the WM read latency W/A with its name
drm/i915/skl: Also detect eDRAM on SKL
...
Bjørn reported that his machine hang during hibernation and eventually
bisected the problem to the following commit:
commit da2bc1b9db
Author: Imre Deak <imre.deak@intel.com>
Date: Thu Oct 23 19:23:26 2014 +0300
drm/i915: add poweroff_late handler
The problem seems to be that after the kernel puts the device into D3
the BIOS still tries to access it, or otherwise assumes that it's in D0.
This is clearly bogus, since ACPI mandates that devices are put into D3
by the OSPM if they are not wake-up sources. In the future we want to
unify more of the driver's runtime and system suspend paths, for example
by skipping all the system suspend/hibernation hooks if the device is
runtime suspended already. Accordingly for all other platforms the goal
is still to properly power down the device during hibernation.
v2:
- Another GEN4 Lenovo laptop had the same issue, while platforms from
other vendors (including mobile and desktop, GEN4 and non-GEN4) seem
to work fine. Based on this apply the workaround on all GEN4 Lenovo
platforms.
- add code comment about failing platforms (Ville)
Reference: http://lists.freedesktop.org/archives/intel-gfx/2015-February/060633.html
Reported-and-bisected-by: Bjørn Mork <bjorn@mork.no>
Cc: stable@vger.kernel.org # v3.19
Signed-off-by: Imre Deak <imre.deak@intel.com>
Acked-by: Daniel Vetter <daniel.vetter@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Again, good riddance to UMS!
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Pull drm updates from Dave Airlie:
"This is the main drm pull, it has a shared branch with some alsa
crossover but everything should be acked by relevant people.
New drivers:
- ATMEL HLCDC driver
- designware HDMI core support (used in multiple SoCs).
core:
- lots more atomic modesetting work, properties and atomic ioctl
(hidden under option)
- bridge rework allows support for Samsung exynos chromebooks to
work finally.
- some more panels supported
i915:
- atomic plane update support
- DSI uses shared DSI infrastructure
- Skylake basic support is all merged now
- component framework used for i915/snd-hda interactions
- write-combine cpu memory mappings
- engine init code refactored
- full ppgtt enabled where execlists are enabled.
- cherryview rps/gpu turbo and pipe CRC support.
radeon:
- indirect draw support for evergreen/cayman
- SMC and manual fan control for SI/CI
- Displayport audio support
amdkfd:
- SDMA usermode queue support
- replace suballocator usage with more suitable one
- rework for allowing interfacing to more than radeon
nouveau:
- major renaming in prep for later splitting work
- merge arm platform driver into nouveau
- GK20A reclocking support
msm:
- conversion to atomic modesetting
- YUV support for mdp4/5
- eDP support
- hw cursor for mdp5
tegra:
- conversion to atomic modesetting
- better suspend/resume support for child devices
rcar-du:
- interlaced support
imx:
- move to using dw_hdmi shared support
- mode_fixup support
sti:
- DVO support
- HDMI infoframe support
exynos:
- refactoring and cleanup, removed lots of internal unnecessary
abstraction
- exynos7 DECON display controller support
Along with the usual bunch of fixes, cleanups etc"
* 'drm-next' of git://people.freedesktop.org/~airlied/linux: (724 commits)
drm/radeon: fix voltage setup on hawaii
drm/radeon/dp: Set EDP_CONFIGURATION_SET for bridge chips if necessary
drm/radeon: only enable kv/kb dpm interrupts once v3
drm/radeon: workaround for CP HW bug on CIK
drm/radeon: Don't try to enable write-combining without PAT
drm/radeon: use 0-255 rather than 0-100 for pwm fan range
drm/i915: Clamp efficient frequency to valid range
drm/i915: Really ignore long HPD pulses on eDP
drm/exynos: Add DECON driver
drm/i915: Correct the base value while updating LP_OUTPUT_HOLD in MIPI_PORT_CTRL
drm/i915: Insert a command barrier on BLT/BSD cache flushes
drm/i915: Drop vblank wait from intel_dp_link_down
drm/exynos: fix NULL pointer reference
drm/exynos: remove exynos_plane_dpms
drm/exynos: remove mode property of exynos crtc
drm/exynos: Remove exynos_plane_dpms() call with no effect
drm/i915: Squelch overzealous uncore reset WARN_ON
drm/i915: Take runtime pm reference on hangcheck_info
drm/i915: Correct the IOSF Dev_FN field for IOSF transfers
drm/exynos: fix DMA_ATTR_NO_KERNEL_MAPPING usage
...
Commit 03dae59c72 ("drm/i915: Ditch UMS config option") removed
CONFIG_DRM_I915_UMS from the Kconfig file, but i915_drv.c still
references this option in two #ifndef statements.
As an undefined config option will always be 'false', we can drop
the #ifndefs alltogether and adapt the printed error message.
This inconsistency was found with the undertaker tool.
Signed-off-by: Andreas Ruprecht <rupran@einserver.de>
[danvet: Undo logging change as requested by Jani.]
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
When run as a timer, i915_hangcheck_elapsed() must adhere to all the
rules of running in a softirq context. This is advantageous to us as we
want to minimise the risk that a driver bug will prevent us from
detecting a hung GPU. However, that is irrelevant if the driver bug
prevents us from resetting and recovering. Still it is prudent not to
rely on mutexes inside the checker, but given the coarseness of
dev->struct_mutex doing so is extremely hard.
Give in and run from a work queue, i.e. outside of softirq.
v2: Use own workqueue to avoid deadlocks (Daniel)
Cleanup commit msg and add comment to i915_queue_hangcheck() (Chris)
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Daniel Vetter <dnaiel.vetter@ffwll.chm>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> (v1)
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
[danvet: Remove accidental kerneldoc comment starter, to appease the 0
day builder.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We don't have full atomic modeset support yet, but the "nuclear
pageflip" subset of functionality (i.e., plane operations only) should
be ready. Allow the user to force atomic on for debug purposes, or for
fixed-purpose embedded devices that will only use atomic for plane
updates.
The term 'nuclear' is used here instead of 'atomic' to make it clear
that this doesn't allow full atomic modeset support, just a (very
useful) subset of the atomic functionality.
We'll drop the kernel parameter and unconditionally enable atomic in a
future patch once all of the necessary pieces are in.
v2:
- Use module_param_named_unsafe() (Daniel)
- Simplify comment on DRIVER_ATOMIC guard (Daniel)
v3:
- Make the parameter "nuclear_pageflip" rather than just "nuclear"
for clarity. (Ander)
v4:
- Make the internal variable "nuclear_pageflip" as well as the
command-line option. (Ander)
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Ander Conselvan de Oliveira <conselvan2@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We have multiple forcewake domains now on recent gens. Change the
function naming to reflect this.
v2: More verbose names (Chris)
v3: Rebase
v4: Rebase
v5: Add documentation for forcewake_get/put
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Deepak S <deepak.s@linux.intel.com> (v2)
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Calling intel_runtime_pm_put() is illegal from a soft-irq context, so
revert the crude hack
commit aa0b3b5bb8
Author: Paulo Zanoni <paulo.r.zanoni@intel.com>
Date: Tue Apr 1 14:55:07 2014 -0300
drm/i915: don't schedule force_wake_timer at gen6_read
and apply the single line corrective instead.
v2: assert forcewake is off after the forcewake_reset (Paulo)
References: https://bugs.freedesktop.org/show_bug.cgi?id=80913
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Deepak S <deepak.s@linux.intel.com> (v1)
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
It seems in the past we have BDW with PCH not been propperly identified
and we force it to be LPT and we were warning !IS_HASWELL on propper identification.
Now that products are out there we are receiveing logs with this incorrect WARN.
And also according to local tests on all production BDW here ULT or HALO we don't
need this force anymore. So let's clean this block for real.
v2: Fix LPT_LP WARNs to avoid wrong warns on BDW_ULT (By Jani).
Reference: https://bugs.freedesktop.org/attachment.cgi?id=110972
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Xion Zhang <xiong.y.zhang@intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Conflicts:
drivers/gpu/drm/i915/intel_runtime_pm.c
Separate branch so that Takashi can also pull just this refactoring
into sound-next.
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
This will be needed by later patches, so factor it out.
No functional change.
v2:
- s/dev_to_i915_priv/dev_to_i915/ (Jani)
- don't use the helper in i915_pm_suspend (Chris)
- simplify the helper (Chris)
v3:
- remove redundant upcasting in the helper (Daniel)
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This reverts commit 355a701838.
This had some bad side effects under normal operation, and should
have been dropped earlier.
Signed-off-by: Dave Airlie <airlied@redhat.com>
With cherryview onwards, Gunit hardware itself save and restore all the
Gunit registers. Skipping the "vlv_save_gunit_s0ix_state" &
"vlv_restore_gunit_s0ix_state" for cherryview in S3/S0ix sequence.
Signed-off-by: Deepak S <deepak.s@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Atm, we don't disable RPS interrupts and related work items before
resetting the GPU. This may interfere with the following GPU
initialization and cause RPS interrupts to show up in PM_IIR too early
before calling gen6_enable_rps_interrupts() (triggering a WARN there).
Solve this by disabling RPS interrupts and flushing any related work
items before resetting the GPU.
v2:
- split out the common parts of the gt suspend and the new gt reset
functions (Paulo)
v3:
- remove the check for UMS, it's a NOP nowadays (Daniel)
Reported-by: He, Shuang <shuang.he@intel.com>
Testcase: igt/gem_reset_stats/ban-render
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=86644
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Otherwise the MST resume paths can hit DPMS paths
which hit state checker paths, which hit WARN_ON,
because the state checker is inconsistent with the
hw.
This fixes a bunch of WARN_ON's on resume after
undocking.
Signed-off-by: Dave Airlie <airlied@redhat.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: stable@vger.kernel.org
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Clear the video overlay state on GPU reset. Any pending overlay request
in the ring has been nuked, and the display itself gets reset. So we
pretty much lose all state here. Adjust the software state to match so
that the next "putimage" will restore things to working order.
v2: Ass a locking check into intel_overlay_release_old_vid() (Daniel)
Cc: Daniel Vetter <daniel@ffwll.ch>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
[danvet: s/0/NULL/ to appease sparse, reported by 0-day tester.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
On gen4 and earlier the GPU reset also resets the display, so we should
protect against concurrent modeset operations. Grab all the modeset locks
around the entire GPU reset dance, remebering first ti dislogde any
pending page flip to make sure we don't deadlock. Any pageflip coming
in between these two steps should fail anyway due to reset_in_progress,
so this should be safe.
This fixes a lot of failed asserts in the modeset code when there's a
modeset racing with the reset. Naturally the asserts aren't happy when
the expected state has disappeared.
v2: Drop UMS checks, complete pending flips after the reset (Daniel)
Cc: Daniel Vetter <daniel@ffwll.ch>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
g33 seems to sit somewhere between the 915/945/965 style and the
g4x style. The bits look like g4x, but we still need to do a full
reset including display.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
915/945 have the same reset registers as 965, so share the code.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
On pre-ctg GPU reset also resets the display hardware. Force a mode
restore after the GPU reset, and also re-init clock gating.
v2: Use intel_modeset_init_hw() instead of intel_init_clock_gating()
in case more relevant stuff gets added there at some point
Restore interrupts after the reset as well
Tested-by: Kenneth Graunke <kenneth@whitecape.org>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
drm-intel-next-2014-11-21:
- infoframe tracking (for fastboot) from Jesse
- start of the dri1/ums support removal
- vlv forcewake timeout fixes (Imre)
- bunch of patches to polish the rps code (Imre) and improve it on bdw (Tom
O'Rourke)
- on-demand pinning for execlist contexts
- vlv/chv backlight improvements (Ville)
- gen8+ render ctx w/a work from various people
- skl edp programming (Satheeshakrishna et al.)
- psr docbook (Rodrigo)
- piles of little fixes and improvements all over, as usual
* tag 'drm-intel-next-2014-11-21-fixed' of git://anongit.freedesktop.org/drm-intel: (117 commits)
drm/i915: Don't pin LRC in GGTT when dumping in debugfs
drm/i915: Update DRIVER_DATE to 20141121
drm/i915/g4x: fix g4x infoframe readout
drm/i915: Only call mod_timer() if not already pending
drm/i915: Don't rely upon encoder->type for infoframe hw state readout
drm/i915: remove the IRQs enabled WARN from intel_disable_gt_powersave
drm/i915: Use ggtt error obj capture helper for gen8 semaphores
drm/i915: vlv: increase timeout when setting idle GPU freq
drm/i915: vlv: fix cdclk setting during modeset while suspended
drm/i915: Dump hdmi pipe_config state
drm/i915: Gen9 shadowed registers
drm/i915/skl: Gen9 multi-engine forcewake
drm/i915: Read power well status before other registers for drpc info
drm/i915: Pin tiled objects for L-shaped configs
drm/i915: Update ring freq for full gpu freq range
drm/i915: change initial rps frequency for gen8
drm/i915: Keep min freq above floor on HSW/BDW
drm/i915: Use efficient frequency for HSW/BDW
drm/i915: Can i915_gem_init_ioctl
drm/i915: Sanitize ->lastclose
...
It happens on occasion that developers of generic user-space applications
abuse the dumb buffer API to get hold of drm buffers that they can both
mmap() and use for GPU acceleration, using the assumptions that dumb buffers
and buffers available for GPU are
a) The same type and can be aribtrarily type-casted.
b) fully coherent.
This patch makes the most widely used drivers warn nicely when that happens,
the next step will be to fail.
v2: Move drmP.h changes to drm_gem.h. Fix Radeon dumb mmap breakage.
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Again just complicates gem init functions and makes a general mess out
of everything.
Good riddance!
v2: In my enthusiasm to start removing dri1/ums crud I went overboard a
bit and killed parts of hangcheck. Resurrect it.
Acked-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
With the deprecation of UMS, and by association DRI1, we have a tough
choice when updating the ring access routines. We either rewrite the
DRI1 routines blindly without testing (so likely to be broken) or take
the liberty of declaring them no longer supported and remove them
entirely. This takes the latter approach.
v2: Also remove the DRI1 sarea updates
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
[danvet: Fix rebase conflicts.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
After the previous patch RPS disabling doesn't depend any more on the
first level interrupts being disabled, so we can move it everywhere
earlier. Doing so let's us think about the uninitialization steps
afterwards independently of any asynchronous RPS events that can happen
atm. It also makes the system/runtime suspend time RPS disabling more
uniform. Finally this gets rid of the WARN in
intel_suspend_gt_powersave(), which we can hit if a final RPS work runs
after we disabled the first level interrupts.
Testcase: igt/pm_rpm
Reference: https://bugs.freedesktop.org/show_bug.cgi?id=82939
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The block was added for spin_lock_irqsave flags, but since the locking
was converted to spin_lock_irq variant, the block is no longer needed.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
With this patch, the RPS sequence for runtime suspend/resume is
exactly like the sequence for S3 suspend/resume:
- flush_delayed_work(&dev_priv->rps.delayed_resume_work)
- intel_runtime_pm_disable_interrupts()
- intel_suspend_gt_powersave()
(suspended)
- intel_runtime_pm_enable_interrupts()
- intel_enable_gt_powersave()
With this, we get rid of WARNs that are currently intermittently
triggered by the system-suspend-execbuf subtest of runtime PM. Notice
that these WARNs could also be triggered in other ways that involved
doing lots of RPM suspend/resume cycles just after a system S3 resume.
Testcase: igt/pm_rpm/system-suspend-execbuf
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reference: https://bugs.freedesktop.org/show_bug.cgi?id=82939
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We want to run intel_uncore_early_sanitize() before we touch any
registers, because on BDW, when we resume, the FPGA_DBG_RM_NOCLAIM bit
is set, so we need to clear it - through intel_uncore_early_sanitize()
- before we do anything else. With the current code, we don't clear
the bit before our first register access, so we print a WARN
complaining about an unclaimed register error.
v1: Was called "drm/i915: run intel_uncore_early_sanitize earlier on
resume"
v2: Was called "drm/i915: run intel_uncore_early_sanitize earlier on
resume on non-VLV"
v3: This one, on top of the intel_resume_prepare() rework.
v4: Rebase.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Because, really, the abstraction is not working for us. It is nice for
VLV, but doesn't add anything useful on SNB/HSW/BDW. We want to change
this code due to a recently-discovered bug, but we can't seem to find
a nice solution that repects the current abstraction. So let's kill
intel_resume_prepare() and its friends, and add an equivalent
implementation to both its callers.
Also, look at the diffstat!
v2: - Rebase.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This will hopefully make it easier to navigate the code without the need
to consult the full PM documentation.
v2:
- add a comment that the freeze handler is also called after rebooting
- add a comment that the thaw handler is also called to recover from
errors (Ville)
- add the PM event names (PMSG_THAW etc.) for reference (Ville)
- add comments that s0ix can be handled both via system and runtime
suspend (Ville)
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
By now we handle switcheroo and legacy suspend/resume the same way, so
no need to keep separate functions for them.
No functional change.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The suspend_late handler saves some registers and powers off the device,
so it doesn't have a big overhead. Calling it at S4 poweroff_late time
makes the power off handling identical to the S3 suspend and S4 freeze
handling, so do this for consistency.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
By now the S4 freeze/thaw and S3 suspend/resume events are handled the
same way, so we can rename the freeze/thaw internal helpers to
suspend/resume accordingly to make clearer what the helpers do. Also
rename i915_resume_early to i915_drm_resume_early aligning it with the
rest of the helper names.
No functional change.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The S3 and S4 events are now handled the same way internally, there is no
need to keep separate wrapper functions around them. Simply reuse the
suspend/resume versions everywhere.
No functional change.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We already disable everything during S4 freeze, except the PCI device
itself. There is no reason why we couldn't disable that too and doing
so allows us to unify these handlers in the next patch with the
corresponding S3 suspend/resume handlers.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
To avoid processing hotplug events we disable connector polling for the
duration of S3 suspend. We also disable it for S4 freeze, and keep it
disabled after S4 thaw. This won't prevent though hotplug processing,
since we re-enable interrupts anyway. There is also no need to prevent
it at that time, since we reinitialize everything during thaw, so the
device is in a consistent state. So to simplify things enable polling
during thaw, which will allow us to handle S4 thaw the same way as S3
resume in an upcoming patch.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Checking for GT faults is not specific in any way to S4 thaw, so do it
also during S3 resume, S4 restore and driver load time. This allows us to
unify the Sx handlers in an upcoming patch.
v2:
- move the check to intel_uncore_early_sanitize(), so we check at driver
load time too (Chris)
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The logic to skip restoring GTT mappings was added to speed up
suspend/resume, but not on old GENs where not restoring them caused
problems. The check for old GENs is based on the existence of OpRegion,
but this doesn't work since opregion is initialized only after
the check. So we end up always restoring the mappings.
On my BYT - which has OpRegion - skipping restoring the mappings during
suspend doesn't work, I get a GPU hang after resume. Also the logic of
when to allow the optimization during S4 is reversed: we should allow it
during S4 thaw but not during S4 restore, but atm we have it the other
way around in the code.
Since correctness wins over optimal code and since the optimization
wasn't used anyway I decided not to try to fix it at this point, but
just remove it. This allows us to unify the S3 and S4 handlers in the
following patches.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
If the device is suspended already through the switcheroo interface we
shouldn't suspend it again or resume it after suspend. We have the
corresponding check for S3 suspend already, add it for all the other
S3 and S4 handlers. Also move the check from i915_resume_early() to
i915_resume_legacy(), so that it's done in the high level handler for
all PM events.
v2:
- fix the resume path too, we don't need to special case there
DRM_SWITCH_POWER_OFF with the device being enabled (in which case we'd
have to disable the device), since that never happens (Ville)
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
During switcheroo/legacy suspend we don't call the suspend_late handler
but when resuming afterwards we call resume_early. This happened to work
so far, since suspend_late only disabled the PCI device. This changed in
commit 016970beb0
Author: Sagar Kamble <sagar.a.kamble@intel.com>
Date: Wed Aug 13 23:07:06 2014 +0530
drm/i915: Sharing platform specific sequence between runtime and system susp
after which we also saved/restored the VLV Gunit HW state in
suspend_late/resume_early. So now since we don't save the state during
suspend a following resume will restore a corrupted state.
Fix this by calling the suspend_late handler during both switcheroo and
legacy suspend.
CC: Sagar Kamble <sagar.a.kamble@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Sagar Kamble <sagar.a.kamble@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
i915_suspend() is called from the DRM legacy S3 suspend/S4 freeze paths
and the switcheroo suspend path. For switcheroo we only ever need to
perform a full suspend (PM_EVENT_SUSPEND) and for the DRM legacy path
we can handle the S4 freeze (PM_EVENT_FREEZE) the same way as S3
suspend. The only difference atm between suspend and freeze is that
during freeze we don't disable the PCI device, but there is no reason
why we can't do so. So unify the two cases to reduce complexity.
Note that for the DRM legacy case the thaw event is not handled, so
we disable the display before creating the hibernation image and it
won't get re-enabled until reboot. We could fix this leaving the
display enabled for the image creation/writing (if we care enough
about UMS), but this can be done as a follow-up.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This is needed by an upcoming patch fixing the switcheroo/legacy suspend
paths.
No functional change.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
During S4 freeze we don't call intel_suspend_complete(), which would
save the gunit HW state, but during S4 thaw/restore events we call
intel_resume_prepare() which restores it, thus ending up in a corrupted
HW state.
Fix this by calling intel_suspend_complete() from the corresponding
freeze_late event handler.
The issue was introduced in
commit 016970beb0
Author: Sagar Kamble <sagar.a.kamble@intel.com>
Date: Wed Aug 13 23:07:06 2014 +0530
CC: Sagar Kamble <sagar.a.kamble@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The legacy DRM suspend logic (effective in UMS) doesn't handle any S4 thaw
events so we don't need to care about it either. Only S3 suspend and S4
freeze events are handled. Leave an assert behind to be sure.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
IS_ULT() wasn't taking into account SKL so we had a warn with SPT-LP.
We don't realy need those checks here, and as we don't need to introduce
IS_SKL_ULT/ULX() at the moment, let's just drop them.
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
No need to add the BDW pci ULT/ULX checks inside a if (IS_HASWELL(dev))
code path.
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
It's the new world order!
Not going full monty on these here and rolling this out throughout the
subsequent call chains since this is just for the kerneldoc. Later on
we can go more crazy, especially once we've embedded drm_device
correctly.
v2: Also frob the runtime_pm functions ...
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This seems to have been accidentally lost in
commit be62acb4cc
Author: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Date: Fri Aug 30 16:19:28 2013 +0300
drm/i915: ban badly behaving contexts
Without this real gpu hangs only log output at info level, which gets
filtered away by piglit's testrunner.
v2: Tune down to notice level. Note that we need to add drm/i915 so
that at least the automatic igt dmesg filtering still picks it up.
v3: git add and lack of coffee don't mix well.
v4: Message is in between hw and sw reset, so switch verb to
continuous form.
v5: Use i915_stop_rings_allow_warn for consistency. For Chris' case of
injecting lots of hangs I guess we need to revamp this all anyway when
merging. For now this should plug the regression for piglit testing
mesa.
v6: Make it compile (Mika).
Cc: Mika Kuoppala <mika.kuoppala@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Kenneth Graunke <kenneth@whitecape.org>
Reported-by: Kenneth Graunke <kenneth@whitecape.org>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Another layer of indirection for just an lpt-only w/a is a bit
excessive. Reduce it.
This was added in
commit 7d708ee40a
Author: Imre Deak <imre.deak@intel.com>
Date: Wed Apr 17 14:04:50 2013 +0300
drm/i915: HSW: allow PCH clock gating for suspend
Cc: Imre Deak <imre.deak@intel.com>
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
SKL stage 1 patches still need polish so will likely miss the 3.18
merge window. We've decided to postpone to 3.19 so let's pull this in
to make patch merging and conflict handling easier.
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Adding new macro IS_SKYLAKE for skylake specific implementation.
Reviewed-by: Thomas Wood <thomas.wood@intel.com>
Signed-off-by: Satheeshakrishna M <satheeshakrishna.m@intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
v2: Squash in 2nd patch from Damien for more ids (Daniel)
v3: info->has*ring -> info->ring_mask conversion. Also add VEBOX support.
v4: Fold in update from Damien
v5: Rebase and add GEN_DEFAULT_PIPEOFFSETS
v6: Add more PCI ID (Vandana)
v7: Rebase and add IVB_CURSOR_OFFSETS
v8: Renamed the macro from _PCI_IDS to _IDS for consistency
Reviewed-by: Thomas Wood <thomas.wood@intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Vandana Kannan <vandana.kannan@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Grab bag for all the special cases:
- i9xx_check_fifo_underruns is only called from crtc_enable hooks,
i.e. process context.
- i915_enable_asle_pipestat is only called from interrupt postinstall
hooks. So again process context.
- gen8_irq_power_well_post_enable is called from the runtime pm code,
which again means process context.
- The open-coded hpd_irq_setup loop in _thaw is also running in process
context.
So for all of them the plain _irq variant is sufficient.
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This was lost in
commit e11aa36230
Author: Jesse Barnes <jbarnes@virtuousgeek.org>
Date: Wed Jun 18 09:52:55 2014 -0700
drm/i915: use runtime irq suspend/resume in freeze/thaw
which makes the second part of this commen a bit nonsense. Both were
originally added in
commit 15239099d7
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Tue Mar 5 09:50:58 2013 +0100
drm/i915: enable irqs earlier when resuming
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Cc: Imre Deak <imre.deak@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Somehow I've overlooked this when simplifying the irq reinit
scheme on gen4.5+ in
commit 78ad455fd2
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Thu May 22 22:18:21 2014 +0200
drm/i915: Improve irq handling after gpu resets
Since display interrups in general survive a gpu reset on those
platforms there's also no need to reinit the hotplug settings.
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
- final bits (again) for the rotation support (Sonika Jindal)
- support bl_power in the intel backlight (Jani)
- vdd handling improvements from Ville
- i830M fixes from Ville
- piles of prep work all over to make skl enabling just plug in (Damien, Sonika)
- rename DP training defines to reflect latest edp standards, this touches all
drm drivers supporting DP (Sonika Jindal)
- cache edids during single detect cycle to avoid re-reading it for e.g. audio,
from Chris
- move w/a for registers which are stored in the hw context to the context init
code (Arun&Damien)
- edp panel power sequencer fixes, helps chv a lot (Ville)
- piles of other chv fixes all over
- much more paranoid pageflip handling with stall detection and better recovery
from Chris
- small things all over, as usual
* tag 'drm-intel-next-2014-09-05' of git://anongit.freedesktop.org/drm-intel: (114 commits)
drm/i915: Update DRIVER_DATE to 20140905
drm/i915: Decouple the stuck pageflip on modeset
drm/i915: Check for a stalled page flip after each vblank
drm/i915: Introduce a for_each_plane() macro
drm/i915: Rewrite ABS_DIFF() in a safer manner
drm/i915: Add comments explaining the vdd on/off functions
drm/i915: Move DP port disable to post_disable for pch platforms
drm/i915: Enable DP port earlier
drm/i915: Turn on panel power before doing aux transfers
drm/i915: Be more careful when picking the initial power sequencer pipe
drm/i915: Reset power sequencer pipe tracking when disp2d is off
drm/i915: Track which port is using which pipe's power sequencer
drm/i915: Fix edp vdd locking
drm/i915: Reset the HEAD pointer for the ring after writing START
drm/i915: Fix unsafe vma iteration in i915_drop_caches
drm/i915: init sprites with univeral plane init function
drm/i915: Check of !HAS_PCH_SPLIT() in PCH transcoder funcs
drm/i915: Use HAS_GMCH_DISPLAY un underrun reporting code
drm/i915: Use IS_BROADWELL() instead of IS_GEN8() in forcewake code
drm/i915: Don't call gen8_fbc_sw_flush() on chv
...
One step closer to dropping all the drm_bus_* code:
Add a driver->set_busid() callback and make all drivers use the generic
helpers. Nouveau is the only driver that uses two different bus-types with
the same drm_driver. This is totally broken if both buses are available on
the same machine (unlikely, but lets be safe). Therefore, we create two
different drivers for each platform during module_init() and set the
set_busid() callback respectively.
Signed-off-by: David Herrmann <dh.herrmann@gmail.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Instead of going through hoops, just put the driver author directly as
DRM_AUTHOR() argument. This will also make it consistent when we add
Intel to the list.
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
On BDW we're seeing a problem that after we runtime resume, the
outputs connected to DDI C are not detected: they don't appear in the
SDEISR register and GMBUS transactions don't work. They stop working
at the moment we call intel_opregion_notify_adapter() during runtime
suspend, but they don't go back to work when we call the same function
during runtime resume. They only work after we do a modeset and call
intel_opregion_notify_encoder(), but this point is already too late.
While debugging, I tried to pass PCI_D3hot which is the value that
matches the spec, and it seems to have solved the problem. I couldn't
find any explanation of why this solves the problem, but there's also
no documented explanation - besides our code and git log - of why
Haswell should use PCI_D1, so keep this for now in order to keep BDW
runtime PM working.
Also add a comment to point the fact that there's no spec documenting
all the weirdness involved here.
Cc: kristen.c.accardi@intel.com
Testcase: igt/pm_rpm/drm-resources-equal
Testcase: igt/pm_rpm/i2c
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This patch is to address Daniels concerns over different code during reset:
http://lists.freedesktop.org/archives/intel-gfx/2014-June/047758.html
"The reason for aiming as hard as possible to use the exact same code for
driver load, gpu reset and runtime pm/system resume is that we've simply
seen too many bugs due to slight variations and unintended omissions."
Tested using igt drv_hangman.
V2: Cleaner way of preventing check_wedge returning -EAGAIN
V3: Clean the last_context during reset, to ensure do_switch() does the MI_SET_CONTEXT. As per review.
Signed-off-by: McAulay, Alistair <alistair.mcaulay@intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
[danvet: Rebase over ctx->ppgtt rework and extend the comment in
check_wedge a bit.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
drm-intel-next-2014-08-22:
- basic code for execlist, which is the fancy new cmd submission on gen8. Still
disabled by default (Ben, Oscar Mateo, Thomas Daniel et al)
- remove the useless usage of console_lock for I915_FBDEV=n (Chris)
- clean up relations between ctx and ppgtt
- clean up ppgtt lifetime handling (Michel Thierry)
- various cursor code improvements from Ville
- execbuffer code cleanups and secure batch fixes (Chris)
- prep work for dev -> dev_priv transition (Chris)
- some of the prep patches for the seqno -> request object transition (Chris)
- various small improvements all over
* tag 'drm-intel-next-2014-09-01' of git://anongit.freedesktop.org/drm-intel: (86 commits)
drm/i915: fix suspend/resume for GENs w/o runtime PM support
drm/i915: Update DRIVER_DATE to 20140822
drm: fix plane rotation when restoring fbdev configuration
drm/i915/bdw: Disable execlists by default
drm/i915/bdw: Enable Logical Ring Contexts (hence, Execlists)
drm/i915/bdw: Document Logical Rings, LR contexts and Execlists
drm/i915/bdw: Print context state in debugfs
drm/i915/bdw: Display context backing obj & ringbuffer info in debugfs
drm/i915/bdw: Display execlists info in debugfs
drm/i915/bdw: Disable semaphores for Execlists
drm/i915/bdw: Make sure gpu reset still works with Execlists
drm/i915/bdw: Don't write PDP in the legacy way when using LRCs
drm/i915: Track cursor changes as frontbuffer tracking flushes
drm/i915/bdw: Help out the ctx switch interrupt handler
drm/i915/bdw: Avoid non-lite-restore preemptions
drm/i915/bdw: Handle context switch events
drm/i915/bdw: Two-stage execlist submit process
drm/i915/bdw: Write the tail pointer, LRC style
drm/i915/bdw: Implement context switching (somewhat)
drm/i915/bdw: Emission of requests with logical rings
...
Conflicts:
drivers/gpu/drm/i915/i915_drv.c
Before sharing common parts between the system and runtime s/r
handlers we WARNed if the runtime s/r handlers were called on GENs that
didn't support RPM. But this WARN is not correct if the same handler is
called from the system s/r path, since that can happen on any platform.
This also broke system s/r on old platforms.
The issue was introduced in
commit 016970beb0
Author: Sagar Kamble <sagar.a.kamble@intel.com>
Date: Wed Aug 13 23:07:06 2014 +0530
v2:
- remove the WARN and depend on the HAS_RUNTIME_PM check in
rutime_suspend/resume instead (Daniel)
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=82751
Signed-off-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Up until recently, semaphores weren't enabled in BDW so we didn't care
about them. But then Rodrigo came and enabled them:
commit 521e62e49a
Author: Rodrigo Vivi <rodrigo.vivi@intel.com>
drm/i915: Enable semaphores on BDW
So now we have to explicitly disable them for Execlists until both
features play nicely.
Signed-off-by: Oscar Mateo <oscar.mateo@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Atm we may leave eDP VDD enabled during system suspend after the CRTCs
are disabled through an HPD->DPCD read event. So disable VDD during
suspend at a point when no HPDs can occur.
Note that runtime suspend doesn't have the same problem, since there the
RPM ref held by VDD provides already the needed serialization.
v2:
- add note to commit message about the runtime suspend path (Ville)
- use edp_panel_vdd_off_sync(), so we can keep the WARN in
edp_panel_vdd_off() (Ville)
v3:
- rebased on -fixes (for_each_intel_encoder()->list_for_each_entry())
(Imre)
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com> (v2)
Cc: stable@vger.kernel.org (3.16+)
[Jani: fix sparse warning reported by Fengguang Wu]
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Make sure these work handlers don't run after we system suspend or
unload the driver. Note that we don't cancel the handlers during runtime
suspend. That could lead to a lockup, since we take a runtime PM ref
from the handlers themselves. Fortunaltely canceling there is not needed
since the RPM ref itself provides for the needed serialization.
v2:
- fix the order of canceling dig_port_work wrt. hotplug_work (Ville)
- zero out {long,short}_hpd_port_mask and hpd_event_bits for speed
(Ville)
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: stable@vger.kernel.org (3.16+)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
On VLV, post S0i3 during i915_drm_thaw following issue is observed during ring
initialization.
[ 335.604039] [drm:stop_ring] ERROR render ring :timed out trying to stop ring
[ 336.607340] [drm:stop_ring] ERROR render ring :timed out trying to stop ring
[ 336.607345] [drm:init_ring_common] ERROR failed to set render ring head to zero ctl 00000000 head 00000000 tail 00000000 start 00000000
[ 337.610645] [drm:stop_ring] ERROR bsd ring :timed out trying to stop ring
[ 338.613952] [drm:stop_ring] ERROR bsd ring :timed out trying to stop ring
[ 338.613956] [drm:init_ring_common] ERROR failed to set bsd ring head to zero ctl 00000000 head 00000000 tail 00000000 start 00000000
[ 339.617256] [drm:stop_ring] ERROR render ring :timed out trying to stop ring
[ 339.617258] -----------[ cut here ]-----------
[ 339.617267] WARNING: CPU: 0 PID: 6 at drivers/gpu/drm/i915/intel_ringbuffer.c:1666 intel_cleanup_ring+0xe6/0xf0()
[ 339.617396] --[ end trace 5ef5ed1a3c92e2a6 ]--
[ 339.617428] [drm:__i915_drm_thaw] ERROR failed to re-initialize GPU, declaring wedged!
This is happening since wake is not enabled and Gunit registers are not restored.
For this system suspend/resume paths need to follow save/restore and additional
platform specific setup in suspend_complete and resume_prepare.
suspend_complete is shared unconditionaly for VLV, HSW, BDW. resume_prepare for
HSW and BDW has pc8 disabling which is needed during thaw_early so sharing
uncondtionally. For VLV and SNB runtime resume specific sequence exists.
Cc: Imre Deak <imre.deak@intel.com>
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Goel, Akash <akash.goel@intel.com>
Signed-off-by: Sagar Kamble <sagar.a.kamble@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
With this change, intel_runtime_suspend and intel_runtime_resume functions
become completely platform agnostic. Platform specific suspend/resume
changes are moved to intel_suspend_complete and intel_resume_prepare.
Cc: Imre Deak <imre.deak@intel.com>
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Goel, Akash <akash.goel@intel.com>
Signed-off-by: Sagar Kamble <sagar.a.kamble@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Rather than take and release the console_lock() around a non-existent
DRM_I915_FBDEV, move the lock acquisation into the callee where it will
be compiled out by the config option entirely. This includes moving the
deferred fb_set_suspend() dance and encapsulating it entirely within
intel_fbdev.c.
v2: Use an integral work item so that we can explicitly flush the work
upon suspend/unload.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
[danvet: Add the flush_work in fbdev_fini per the mailing list
discussion. And s/BUG_ON/WARN_ON/ because.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This reverts commit 521e62e49a.
Although POST_SYNC brought a bit of stability to Semaphores on BDW
it didn't solved all issues and some hungs can still occour when
semaphores are enabled on BDW. Also some sloweness can be found on some
igt tests, althoguth it apparently doesn't affect real workloads.
Besides that, no real performance gain was found on our tests with different
and even multiple workloads.
Let's disable it again for now. At least until we are sure it is safe
to re-enable it.
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Pull in drm-next with Dave's DP MST support so that I can merge some
conflicting patches which also touch the driver load sequencing around
interrupt handling.
Conflicts:
drivers/gpu/drm/i915/intel_display.c
drivers/gpu/drm/i915/intel_dp.c
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
When I moved the irq disable down to after display disable,
I didn't realise the gt suspend also required irqs off, so move it
down as well.
Fixes WARNs seen at suspend/resume time.
v2: moved the rps flush down as well.
Tested-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
By the time I wrote this patch, it allowed me to catch some problems.
But due to patch reordering - in order to prevent fake "regression"
reports - this patch may be merged after the fixes of the problems
identified by this patch.
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
On VLV, after i915_pm_suspend display power wells are staying
power ungated. So, after initiating mem sleep "echo mem > /sys/power/state"
Display is staing D0 State. There might be better way/place to power gate
these wells. Also, we need to make sure that if wells are power gated due to
DPMS OFF sequence, they need not be turned off by i915_pm_suspend again.
v2: Extracted helper for intel_crtc_disable and power gating CRTC power wells.
[Daniel]
Cc: Imre Deak <imre.deak@intel.com>
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Change-Id: I34c80da66aa24c423a5576c68aa1f3a8d0f43848
Signed-off-by: Borun Fu <borun.fu@intel.com>
Signed-off-by: Sagar Kamble <sagar.a.kamble@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This adds DP 1.2 MST support on Haswell systems.
Notes:
a) this reworks irq handling for DP MST ports, so that we can
avoid the mode config locking in the current hpd handlers, as
we need to process up/down msgs at a better time.
Changes since v0.1:
use PORT_PCH_HOTPLUG to detect short vs long pulses
add a workqueue to deal with digital events as they can get blocked on the
main workqueue beyong mode_config mutex
fix a bunch of modeset checker warnings
acks irqs in the driver
cleanup the MST encoders
Changes since v0.2:
check irq status again in work handler
move around bring up and tear down to fix DPMS on/off
use path properties.
Changes since v0.3:
updates for mst apis
more state checker fixes
irq handling improvements
fbcon handling support
improved reference counting of link - fixes redocking.
Changes since v0.4:
handle gpu reset hpd reinit without oopsing
check link status on HPD irqs
fix suspend/resume
Changes since v0.5:
use proper functions to get max link/lane counts
fix another checker backtrace - due to connectors disappearing.
set output type in more places fro, unknown->displayport
don't talk to devices if no HPD asserted
check mst on short irqs only
check link status properly
rebase onto prepping irq changes.
drop unsued force_act
Changes since v0.6:
cleanup unused struct entry.
[airlied: fix some sparse warnings].
Reviewed-by: Todd Previte <tprevite@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
- fbc improvements when stolen memory is tight (Ben)
- cdclk handling improvements for vlv/chv (Ville)
- proper fix for stuck primary planes on gmch platforms with cxsr (Imre&Ebgert
Eich)
- gen8 hw semaphore support (Ben)
- more execlist prep work from Oscar Mateo
- locking fixes for primary planes (Matt Roper)
- code rework to support runtime pm for dpms on hsw/bdw (Paulo, Imre & me), but
not yet enabled because some fixes from Paulo haven't made the cut
- more gpu boost tuning from Chris
- as usual piles of little things all over
* tag 'drm-intel-next-2014-07-11' of git://anongit.freedesktop.org/drm-intel: (93 commits)
drm/i915: Make the RPS interrupt generation mask handle the vlv wa
drm/i915: Move RPS evaluation interval counters to i915->rps
drm/i915: Don't cast a pointer to void* unnecessarily
drm/i915: don't read LVDS regs at compute_config time
drm/i915: check the power domains in intel_lvds_get_hw_state()
drm/i915: check the power domains in ironlake_get_pipe_config()
drm/i915: don't skip shared DPLL assertion on LPT
drm/i915: Only touch WRPLL hw state in enable/disable hooks
drm/i915: Switch to common shared dpll framework for WRPLLs
drm/i915: ->enable hook for WRPLLs
drm/i915: ->disable hook for WRPLLs
drm/i915: State readout support for WRPLLs
drm/i915: add POWER_DOMAIN_PLLS
drm/i915: Document that the pll->mode_set hook is optional
drm/i915: Basic shared dpll support for WRPLLs
drm/i915: Precompute static ddi_pll_sel values in encoders
drm/i915: BDW also has special-purpose DP DDI clocks
drm/i915: State readout and cross-checking for ddi_pll_sel
drm/i915: Move ddi_pll_sel into the pipe config
drm/i915: Add a debugfs file for the shared dpll state
...
- Accurate frontbuffer tracking and frontbuffer rendering invalidate, flush and
flip events. This is prep work for proper PSR support and should also be
useful for DRRS&fbc.
- Runtime suspend hardware on system suspend to support the new SOix sleep
states, from Jesse.
- PSR updates for broadwell (Rodrigo)
- Universal plane support for cursors (Matt Roper), including core drm patches.
- Prefault gtt mappings (Chris)
- baytrail write-enable pte bit support (Akash Goel)
- mmio based flips (Sourab Gupta) instead of blitter ring flips
- interrupt handling race fixes (Oscar Mateo)
And old, not yet merged features from the previous round:
- rps/turbo support for chv (Deepak)
- some other straggling chv patches (Ville)
- proper universal plane conversion for the primary plane (Matt Roper)
- ppgtt on vlv from Jesse
- pile of cleanups, little fixes for insane corner cases and improved debug
support all over
* tag 'drm-intel-next-2014-06-20' of git://anongit.freedesktop.org/drm-intel: (99 commits)
drm/i915: Update DRIVER_DATE to 20140620
drivers/i915: Fix unnoticed failure of init_ring_common()
drm/i915: Track frontbuffer invalidation/flushing
drm/i915: Use new frontbuffer bits to increase pll clock
drm/i915: don't take runtime PM reference around freeze/thaw
drm/i915: use runtime irq suspend/resume in freeze/thaw
drm/i915: Properly track domain of the fbcon fb
drm/i915: Print obj->frontbuffer_bits in debugfs output
drm/i915: Introduce accurate frontbuffer tracking
drm/i915: Drop schedule_back from psr_exit
drm/i915: Ditch intel_edp_psr_update
drm/i915: Drop unecessary complexity from psr_inactivate
drm/i915: Remove ctx->last_ring
drm/i915/chv: Ack interrupts before handling them (CHV)
drm/i915/bdw: Ack interrupts before handling them (GEN8)
drm/i915/vlv: Ack interrupts before handling them (VLV)
drm/i915: Ack interrupts before handling them (GEN5 - GEN7)
drm/i915: Don't BUG_ON in i915_gem_obj_offset
drm/i915: Grab dev->struct_mutex in i915_gem_pageflip_info
drm/i915: Add some L3 registers to the parser whitelist
...
Conflicts:
drivers/gpu/drm/i915/i915_drv.c
To achieve further power savings during system freeze (aka connected
standby, or s0ix) we have to send a PCI_D1 opregion notification. As
the information about the state we're entering (system freeze,
suspend to ram or suspend to disk) is only available through the ACPI
subsystem, make this support depend on the relevant kconfig option.
Things will still work if this option isn't set, albeit with less than
optimial power saving.
This also fixes a compile breakage when the option is not set introduced
in
commit e5747e3adc
Author: Jesse Barnes <jbarnes@virtuousgeek.org>
Date: Thu Jun 12 08:35:47 2014 -0700
drm/i915: send proper opregion notifications on suspend/resume
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Some drivers need to be able to have a perfect race-free fbcon setup.
Current drivers only enable hotplug processing after the call to
drm_fb_helper_initial_config which leaves a tiny but important race.
This race is especially noticable on embedded platforms where the
driver itself enables the voltage for the hdmi output, since only then
will monitors (after a bit of delay, as usual) respond by asserting
the hpd pin.
Most of the infrastructure is already there with the split-out
drm_fb_helper_init. And drm_fb_helper_initial_config already has all
the required locking to handle concurrent hpd events since
commit 53f1904bce
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Thu Mar 20 14:26:35 2014 +0100
drm/fb-helper: improve drm_fb_helper_initial_config locking
The only missing bit is making drm_fb_helper_hotplug_event save
against concurrent calls of drm_fb_helper_initial_config. The only
unprotected bit is the check for fb_helper->fb.
With that drivers can first initialize the fb helper, then enabel
hotplug processing and then set up the initial config all in a
completely race-free manner. Update kerneldoc and convert i915 as a
proof of concept.
Feature requested by Thierry since his tegra driver atm reliably boots
slowly enough to misses the hotplug event for an external hdmi screen,
but also reliably boots to quickly for the hpd pin to be asserted when
the fb helper calls into the hdmi ->detect function.
Cc: Thierry Reding <treding@nvidia.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
It is possible that, by the time we run i915_drm_freeze(),
delayed_resume_work was already queued but did not run yet. If it
still didn't run after intel_runtime_pm_disable_interrupts(), by the
time it runs it will try to change the interrupt registers with the
interrupts already disabled, which will trigger a WARN. We can
reliably reproduce this with the pm_rpm system-suspend test case.
In order to avoid the problem, we have to flush the work before
disabling the interrupts. We could also cancel the work instead of
flushing it, but that would require us to put a runtime PM reference -
and any other resource we may need in the future - in case the work
was already queued, so I believe flushing the work is more
future-proof, although less efficient. But I can also change this part
if someone requests.
Another thing I tried was to move the intel_suspend_gt_powersave()
call to before intel_runtime_pm_disable_interrupts(), but since that
function needs to be called after the interrupts are already disabled,
due to dev_priv->rps.work, this strategy didn't work.
Testcase: igt/pm_rpm/system-suspend
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=80517
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
We should be taking the right power well refs these days, so this
shouldn't be necessary. It also gets in the way of re-using these
routines for S0iX states, as those need all the power saving features
enabled.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We don't need to uninstall the full handler, simply disabling interrupts
ought to be enough.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Jesse's SOix work required some patches from acpi-next, so pull it in
through a topic barnch.
Conflicts:
drivers/gpu/drm/i915/i915_drv.c
drivers/gpu/drm/i915/intel_pm.c
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Atm, the forcewake refcount will be incorrectly set to zero during
system suspend if there is any reference held via the
i915_forcewake_user debugfs entry.
Fix this by simply not zeroing the sw counters during suspend and
restoring the original state using them. Note that the only other
places where we zeroed the counters were driver load and unload time,
where it was redundant anyway.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=78059
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This matches the runtime suspend paths and allows the system to enter
the lowest power mode at freeze time.
v2: move disable_pc8 call to thaw_early (Imre)
move enable_pc8 to freeze_late (Imre/Jesse)
v3: drop spurious hunk from _freeze now that we have freeze_late (Jesse)
v4: move back to suspend_late (Imre was right)
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Kristen Carlson Accardi <kristen@linux.intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This indicates to the firmware that it can power down various other
components or bring them back up, depending on the target system state.
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Kristen Carlson Accardi <kristen@linux.intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This allows the system to enter the lowest power mode during system freeze.
v2: delete force wake timer at suspend (Imre)
v3: add GT work suspend function (Imre)
v4: use uncore forcewake reset (Daniel)
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Kristen Carlson Accardi <kristen@linux.intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We want to make sure everything is disabled and at its lowest power when
freezing.
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Kristen Carlson Accardi <kristen@linux.intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
These are just single registers so wasting space for the pipe offsets
seems a bit pointless. So just use the _PIPE3() macro instead.
Also rewrite the _PIPE3() macro to be more obvious, and protect the
arguments properly.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
[danvet: Frob conflict.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
BDW uses IVB cursor offsets.
Whithout this patch it is not possible to use multiple outputs with cursor
on BDW.
The cursor gets completely crazy because update position uses the wrong
cursor register for the second pipe.
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Cc: stable@vger.kernel.org
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=79621
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
If both KMS is disabled (by i915.modeset=0 or nomodeset parameters) and
UMS is disabled (by CONFIG_DRM_I915_UMS=n, the default), the user might
not be aware his setup is not supported. Inform the users (and, by
extension, the poor i915 developers having to read their dmesgs in bug
reports) why their graphics experience might be lacking.
A similar message was added on the UMS path in
commit e147accbd1
Author: Jani Nikula <jani.nikula@intel.com>
Date: Thu Oct 10 15:25:37 2013 +0300
drm/i915: tell the user KMS is required for gen6+
but it won't be reached if CONFIG_DRM_I915_UMS=n since
commit b30324adaf
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Wed Nov 13 22:11:25 2013 +0100
drm/i915: Deprecated UMS support
v2: Use DRM_DEBUG_DRIVER.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Currently we do a full re-init of all interrupts after a gpu hang.
Which is pretty bad since we don't restore the interrupts we've
enabled at runtime correctly. Even with that addressed it's rather
horribly race.
But on g4x and later we only reset the gt and not the entire gpu.
Which means we only need to reset the GT interrupt bits. Which has the
nice benefit that vblank waits, pipe CRC interrupts and everything
else display related just keeps on working.
The downside is that gt interrupt handling (i.e. ring->get/put_irq) is
still racy. But as long as the gpu hang reliably wakes all waters and
we have a short time where the refcount drops to 0 we'll recover. So
not that bad really.
v2: Ville noticed that GTIMR and PMIMR don't get cleared, only the
subordinate per-ring registers. So let's rip out all the interrupt dancing.
The FIXME comment is still required though since the ring irq handling
happens at the per-ring interrupt mask registers, too.
Testcase: igt/kms_flip/vblank-vs-hang
Testcase: igt/kms_pipe_crc_basic/hang-*
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
After the split-out of crtc locks from the big mode_config.mutex
there's still two major areas it protects:
- Various connector probe states, like connector->status, EDID
properties, probed mode lists and similar information.
- The links from connector->encoder and encoder->crtc and other
modeset-relevant connector state (e.g. properties which control the
panel fitter).
The later is used by modeset operations. But they don't really care
about the former since it's allowed to e.g. enable a disconnected VGA
output or with a mode not in the probed list.
Thus far this hasn't been a problem, but for the atomic modeset
conversion Rob Clark needs to convert all modeset relevant locks into
w/w locks. This is required because the order of acquisition is
determined by how userspace supplies the atomic modeset data. This has
run into troubles in the detect path since the i915 load detect code
needs _both_ protections offered by the mode_config.mutex: It updates
probe state and it needs to change the modeset configuration to enable
the temporary load detect pipe.
The big deal here is that for the probe/detect users of this lock a
plain mutex fits best, but for atomic modesets we really want a w/w
mutex. To fix this lets split out a new connection_mutex lock for the
modeset relevant parts.
For simplicity I've decided to only add one additional lock for all
connector/encoder links and modeset configuration states. We have
piles of different modeset objects in addition to those (like bridges
or panels), so adding per-object locks would be much more effort.
Also, we're guaranteed (at least for now) to do a full modeset if we
need to acquire this lock. Which means that fine-grained locking is
fairly irrelevant compared to the amount of time the full modeset will
take.
I've done a full audit, and there's just a few things that justify
special focus:
- Locking in drm_sysfs.c is almost completely absent. We should
sprinkle mode_config.connection_mutex over this file a bit, but
since it already lacks mode_config.mutex this patch wont make the
situation any worse. This is material for a follow-up patch.
- omap has a omap_framebuffer_flush function which walks the
connector->encoder->crtc links and is called from many contexts.
Some look like they don't acquire mode_config.mutex, so this is
already racy. Again fixing this is material for a separate patch.
- The radeon hot_plug function to retrain DP links looks at
connector->dpms. Currently this happens without any locking, so is
already racy. I think radeon_hotplug_work_func should gain
mutex_lock/unlock calls for the mode_config.connection_mutex.
- Same applies to i915's intel_dp_hot_plug. But again, this is already
racy.
- i915 load_detect code needs to acquire this lock. Which means the
w/w dance due to Rob's work will be nicely contained to _just_ this
function.
I've added fixme comments everywhere where it looks suspicious but in
the sysfs code. After a quick irc discussion with Dave Airlie it
sounds like the lack of locking in there is due to sysfs cleanup fun
at module unload.
v1: original (only compile tested)
v2: missing mutex_init(), etc (from Rob Clark)
v3: i915 needs more care in the conversion:
- Protect the edp pp logic with the connection_mutex.
- Use connection_mutex in the backlight code due to
get_pipe_from_connector.
- Use drm_modeset_lock_all in suspend/resume paths.
- Update lock checks in the overlay code.
Cc: Alex Deucher <alexdeucher@gmail.com>
Cc: Rob Clark <robdclark@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Rob Clark <robdclark@gmail.com>
Atm, we disable GT power saving during the end of the suspend sequence
in i915_save_state(). Doing the disabling at that point seems arbitrary.
One reason to disable it early though is to have a quiescent HW state
before we do anything else (for example save registers). So move the
disabling earlier, which also takes care canceling of the deferred RPS
enabling work done by intel_disable_gt_powersave().
Note that after the move we'll call intel_disable_gt_powersave() only
in case modeset is enabled, but that's anyway the only case where we
have it enabled in the first place.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Robert Beckett <robert.beckett@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Currently user space can access GEM buffers mapped to GTT through
existing mappings concurrently while the platform specific suspend
handlers are running. Since these handlers may change the HW state in a
way that would break such accesses, remove the mappings before calling
the handlers. Spotted by Ville.
Also Chris pointed out that the lists that i915_gem_release_all_mmaps()
walks through need dev->struct_mutex, so take this lock. There is a
potential deadlock against a concurrent RPM resume, resolve this by
aborting and rescheduling the suspend (Daniel).
v2:
- take struct_mutex around i915_gem_release_all_mmaps() (Chris, Daniel)
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Robert Beckett <robert.beckett@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Daniel keeps on ramping up the warning level of the DRM and our display
core to make it complain whenever the locking rules are not followed.
This caught
commit 24576d2397
Author: Jesse Barnes <jbarnes@virtuousgeek.org>
Date: Tue Mar 26 09:25:45 2013 -0700
drm/i915: enable VT switchless resume v3
introducing an unlocked access to the CRTC whilst disabling it for
suspend.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=78114
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We really just want to go detect displays again and fire off a hotplug
event if things have changed, not go through full hotplug processing.
Requested-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
CHV has three pipes so let's expose them all.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Antti Koskipää <antti.koskipaa@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Unsurprisingly the cursor C regiters are also at a weird offset on CHV.
Add more pipe offsets to handle them.
This also gets rid of most of the differences between the i9xx vs. ivb
cursor code. We can unify the remaining code as well, but I'll leave
that for another patch.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Antti Koskipää <antti.koskipaa@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Add support for the third pipe in cherrview
v2: Don't use spaces for indentation (Jani)
Wrap long lines
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Rafael Barbalho <rafael.barbalho@intel.com>
[vsyrjala: slightly massaged the patch]
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Patch done using the following semantic patch (thanks Daniel for the
help!)
@@
iterator name list_for_each_entry;
iterator name for_each_crtc;
struct drm_crtc * crtc;
struct drm_device * dev;
@@
-list_for_each_entry(crtc,&dev->mode_config.crtc_list, head) {
+for_each_crtc(dev,crtc) {
...
}
Followed by a couple of fixups by hand (that spatch doesn't match the
cases where list_for_each_entry() is not followed by a set of '{', '}',
but I couldn't figure out a way to leave the '{' out of the iterator
match).
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
v2: Update to also fill in the new num_pipes field.
v3: Rebase on top of the pciid extraction.
v4: Switch from info->has*ring to info->ring mask. Also add VEBOX support whiel
at it.
v5: s/CHV_PCI_IDS/CHV_IDS/, and drop the trailing '\'
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Add runtime PM support for VLV, but leave it disabled. The next patch
enables it.
The suspend/resume sequence used is based on [1] and [2]. In practice we
depend on the GT RC6 mechanism to save the HW context depending on the
render and media power wells. By the time we run the runtime suspend
callback the display side is also off and the HW context for that is
managed by the display power domain framework.
Besides the above there are Gunit registers that depend on a system-wide
power well. This power well goes off once the device enters any of the
S0i[R123] states. To handle this scenario, save/restore these Gunit
registers. Note that this is not the complete register set dictated by
[2], to remove some overhead, registers that are known not to be used are
ignored. Also some registers are fully setup by initialization functions
called during resume, these are not saved either. The list of registers
can be further reduced, see the TODO note in the code.
[1] VLV_gfx_clocking_PM_reset_y12w21d3 / "Driver D3 entry/exit"
[2] VLV2_S0IXRegs
v2:
- unchanged
v3:
- fix s/GEN6_PMIIR/GEN6_PMIMR/ typo when saving/restoring registers
(Ville)
v4:
- rebased on the previous patch fixing GEN register prefixes
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
[ rebased (according to v4) ]
Signed-off-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Atm, none of the RPM callbacks can fail, but the next patch adding
RPM support for VLV changes this, so prepare for it.
In case one of these callbacks return error RPM will get permanently
disabled until the error is explicitly cleared. In the future we could
add support for re-enabling it, for example after resetting the HW, but
for now - hopefully - we can live with the simpler solution.
v2:
- propagate the error from the resume callbacks too (Paulo)
v3:
- fix rebase fail typo around IS_GEN6() check in intel_runtime_suspend()
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
I've seen latencies up to 15msec, so increase the timeout to 20msec.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This will be needed by the VLV runtime PM helpers too, so factor it out.
Also add a safety check for the case where the previous force-off is
still pending, since I'm not sure if Punit can handle a new setting
while the previous one hasn't settled yet.
v2:
- unchanged
v3:
- add a note to the commit message about the safety check (Ville)
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
During runtime suspend there can be a last pending rps.work, so make
sure it's canceled. Note that in the runtime suspend callback we can't
get any RPS interrupts since it's called only after the GPU goes idle
and we set the minimum RPS frequency. The next possibility for an RPS
interrupt is only after getting an RPM ref (for example because of a new
GPU command) and calling the RPM resume callback.
v2:
- patch introduced in v2 of the patchset
v3:
- Change the order of canceling the rps.work and disabling interrupts to
avoid the race between interrupt disabling and the the rps.work. Race
spotted by Ville.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We need to re-init sizzling on all platforms so move it to the
platform independent runtime resume callback. The ring frequency reinit
is also needed everywhere except on VLV, but gen6_update_ring_freq()
will be a noop on VLV, so we can move this function too to platform
independent code.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This is needed by the next patch moving the call out from platform
specific RPM callbacks to platform independent code.
No functional change.
v2:
- patch introduce in v2 of the patchset
v3:
- simplify platform check condition (Ville)
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We need to disable the interrupts for all platforms, so make the helpers
for this platform independent and call them from them platform
independent runtime suspend/resume callbacks.
On HSW/BDW this will move interrupt disabling/re-enabling at the
beginning/end of runtime suspend/resume respectively, but I don't see
any reason why this would cause a problem there. In any case this seems
to be the correct thing to do even on those platforms.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
On VLV we depend on RC6 to save the GT render and media HW context
before going to the D3 state via RPM, so as a preparation for the
VLV RPM support (added in an upcoming patch) disable RPM if RC6 is
disabled.
There is probably a similar dependency on other platforms too, so for
safety require RC6 for those too. For these platforms (SNB, HSW, BDW)
this is then a possible fix.
v2:
- require RC6 for all RPM platforms, not just for VLV (Paulo, Daniel)
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
At least on VLV but probably on other platforms too we depend on RC6
being enabled for RPM, so disable RPM until the delayed RC6 enabling
completes.
v2:
- explain the reason for the _noresume version of RPM get (Daniel)
- use the simpler 'if (schedule_work()) rpm_get();' instead of
'if (!cancel_work_sync()) rpm_get(); schedule_work();'
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Getting struct_mutex around the whole intel_enable_gt_powersave()
function is not necessary, since it's only needed for the ILK path
therein.
This will make intel_enable_gt_powersave() useable on the RPM resume
path for >=GEN6 (added in an upcoming patch to reset the RPS state
during RPM resume), where we can't (and need not) get this mutex.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Based on the hardware spec, the BDW GT3 machine has two independent
BSD ring that can be used to dispatch the video commands.
So just initialize it.
V3->V4: Follow Imre's comment to do some minor updates. For example:
more comments are added to describe the semaphore between ring.
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
[danvet: Fix up checkpatch error.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Based on the hardware spec, the BDW GT3 has the different configuration
with the BDW GT1/GT2. So split the BDW device info definition.
This is to do the preparation for adding the Dual BSD rings on BDW GT3 machine.
V1->V2: Follow Daniel's comment to pay attention to the stolen check for BDW
in kernel/early-quirks.c
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
During module load, if we fail to initialise the rings, we abort the
load reporting EIO. However during resume, even though we report EIO as
we fail to reinitialize the ringbuffers, the resume continues and the
device is restored - albeit in a non-functional state. As we cannot
execute any commands on the GPU, it is effectively wedged, mark it so.
As we now preserve the ringbuffers across resume, this should prevent
UXA from falling into the trap of repeatedly sending invalid
batchbuffers and dropping all further rendering into /dev/null.
Reported-and-tested-by: Jiri Kosina <jkosina@suse.cz>
References: https://bugs.freedesktop.org/show_bug.cgi?id=76554
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Oscar Mateo <oscar.mateo@intel.com>
[danvet: Drop unused error, spotted by Oscar.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Next pull request, this time more of the drm de-midlayering work. The big
thing is that his patch series here removes everything from drm_bus except
the set_busid callback. Thierry has a few more patches on top of this to
make that one optional to.
With that we can ditch all the non-pci drm_bus implementations, which
Thierry has already done for the fake tegra host1x drm_bus.
Reviewed by Thierry, Laurent and David and now also survived some testing
on my intel boxes to make sure the irq fumble is fixed correctly ;-) The
last minute rebase was just to add the r-b tags from Thierry for the 2
patches I've redone.
* 'drm-init-cleanup' of git://people.freedesktop.org/~danvet/drm:
drm/<drivers>: don't set driver->dev_priv_size to 0
drm: Remove dev->kdriver
drm: remove drm_bus->get_name
drm: rip out dev->devname
drm: inline drm_pci_set_unique
drm: remove bus->get_irq implementations
drm: pass the irq explicitly to drm_irq_install
drm/irq: Look up the pci irq directly in the drm_control ioctl
drm/irq: track the irq installed in drm_irq_install in dev->irq
drm: rename dev->count_lock to dev->buf_lock
drm: Rip out totally bogus vga_switcheroo->can_switch locking
drm: kill drm_bus->bus_type
drm: remove drm_dev_to_irq from drivers
drm/irq: remove cargo-culted locking from irq_install/uninstall
drm/irq: drm_control is a legacy ioctl, so pci devices only
drm/pci: fold in irq_by_busid support
drm/irq: simplify irq checks in drm_wait_vblank
Unfortunately this requires a drm-wide change, and I didn't see a sane
way around that. Luckily it's fairly simple, we just need to inline
the respective get_irq implementation from either drm_pci.c or
drm_platform.c.
With that we can now also remove drm_dev_to_irq from drm_irq.c.
Reviewed-by: Thierry Reding <treding@nvidia.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The dev->struct_mutex locking in drm_irq.c only protects
dev->irq_enabled. Which isn't really much at all and only prevents
especially nasty ums userspace from concurrently installing the
interrupt handling a few times. Or at least trying.
There are tons of unlocked readers of dev->irqs_enabled in the vblank
wait code (and by extension also in the pageflip code since that uses
the same vblank timestamp engine).
Real modesetting drivers should ensure that nothing can go haywire
with a sane setup teardown sequence. So we only really need this for
the drm_control ioctl, everywhere else this will just paper over
nastiness.
Note that drm/i915 is a bit specially due to the gem+ums combination.
So there we also need to properly protect the entervt and leavevt
ioctls. But it's definitely saner to do everything in one go than to
drop the lock in-between.
Finally there's the gpu reset code in drm/i915. That one's just race
(concurrent userspace calls to for vblank waits of pageflips could
spuriously fail). So wrap it up in with a nice comment since fixing
this is more involved.
v2: Rebase and fix commit message (Thierry)
Reviewed-by: Thierry Reding <treding@nvidia.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Backmerge drm-next after the big s/crtc->fb/crtc->primary->fb/
cocinelle patch to avoid endless amounts of conflict hilarity in my
-next queue for 3.16.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
During resume the intel hda audio driver depends on the i915 driver
reinitializing the audio power domain. Since the order of calling the
i915 resume handler wrt. that of the audio driver is not guaranteed,
move the power domain reinitialization step to the resume_early
handler. This is guaranteed to run before the resume handler of any
other driver.
The power domain initialization in turn requires us to enable the i915
pci device first, so move that part earlier too.
Accordingly disabling of the i915 pci device should happen after the
audio suspend handler ran. So move the disabling later from the i915
resume handler to the resume_late handler.
v2:
- move intel_uncore_sanitize/early_sanitize earlier too, so they don't
get reordered wrt. intel_power_domains_init_hw()
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=76152
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Takashi Iwai <tiwai@suse.de>
Cc: stable@vger.kernel.org
[danvet: Add cc: stable and loud comments that this is just a hack.]
[danvet: Fix "Should it be static?" sparse warning reported by Wu
Fengguang's kbuilder.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This sould be enough.
v2: BDW should also run hsw_runtime_resume (Ben).
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Now that PC8 is part of runtime PM, the check is useless.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Just because I have a SNB machine and I can easily test it.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We're adding runtime suspend support to more platforms, so organize
the code in a way that all a new platform needs to do is to add its
own gen-specific functions. Also rename the i915_ functions to intel_
to make it clear that it's the top level one, not something that just
runs on i915 platforms.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Remove the rest of the references to drm_i915_private_t. No functional
changes.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
[danvet: Drop hunk in i915_cmd_parser.c]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
After we removed all the intermediate abstractions, we can rename
these functions to just hsw_{en,dis}able_pc8.
v2: - Rebase.
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We already get runtime PM references, and PC8 is now part of runtime
PM, so this is enough.
v2: - Rebase.
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Currently, when our driver becomes idle for i915.pc8_timeout (default:
5s) we enable PC8, so we save some power, but not everything we can.
Then, while PC8 is enabled, if we stay idle for more
autosuspend_delay_ms (default: 10s) we'll enter runtime PM and put the
graphics device in D3 state, saving even more power. The two features
are separate things with increasing levels of power savings, but if we
disable PC8 we'll never get into D3.
While from the modularity point of view it would be nice to keep these
features as separate, we have reasons to merge them:
- We are not aware of anybody wanting a "PC8 without D3" environment.
- If we keep both features as separate, we'll have to to test both
PC8 and PC8+D3 code paths. We're already having a major pain to
make QA do automated testing of just one thing, testing both paths
will cost even more.
- Only Haswell+ supports PC8, so if we want to add runtime PM support
to, for example, IVB, we'll have to copy some code from the PC8
feature to runtime PM, so merging both features as a single thing
will make it easier for enabling runtime PM on other platforms.
This patch only does the very basic steps required to have PC8 and
runtime PM merged on a single feature: the next patches will take care
of cleaning up everything.
v2: - Rebase.
v3: - Rebase.
- Fully remove the deprecated i915 params since Daniel doesn't
consider them as part of the ABI.
v4: - Rebase.
- Fix typo in the commit message.
v5: - Rebase, again.
- Add a huge comment explaining the different forcewake usage
(Chris, Daniel).
- Use open-coded forcewake functions (Daniel).
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Now that we regularly defer the forcewake dance to a timer func, it is
likely to fire after we disable the device during suspend. This
generates an oops as we detect inconsistency in the hardware state. So
before suspend, we want to complete the outstanding dance and generally
sanitize the registers before handing back to the BIOS.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJTHSaRAAoJEHm+PkMAQRiG7G8IAJHElwFDNSQE7Y9MmbicrAMG
kfjhBtBpTaVrJKQXegCNUwDaLLyC4oLIxDheW84oPXbrEGDLqPtBov/hrcFkHVr4
lh/ZYk02nYtcfpN0JnL/Yj2oKHVmBWs0vFlM7StSFsJCj10DoCVQQdmAJ8XODTPo
CXMapk+UikTX1TlIO8+B5toyl3R1OqPmW211UV1vQVLKy66hu+MKVN/V+/EyopL0
1jO81EDpaRaeIJh1/okcyUoIq9pqLkAWNpeQ7uyXZ+Sfivt9RXwLYKmAB3lP20Hc
ZMIIoHSCyYRFjxLlQvt02bA9nY4wTY7YN5kZ2kk65y7TFfhcGsCw1Sc69iyCoKs=
=CJcA
-----END PGP SIGNATURE-----
Merge tag 'v3.14-rc6' into drm-intel-next-queued
Linux 3.14-rc6
I need the hdmi/dvi-dual link fixes in 3.14 to avoid ugly conflicts
when merging Ville's new hdmi cloning support into my -next tree
Conflicts:
drivers/gpu/drm/i915/Makefile
drivers/gpu/drm/i915/intel_dp.c
Makefile cleanup conflicts with an acpi build fix, intel_dp.c is
trivial.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
BDW is no longer flagged as preliminary hw, but without
i915.preliminary_hw_support module param set the logs are filled with
WARNs about it.
Just make semaphores off the BDW per-chip default for now.
CC: Ben Widawsky <ben@bwidawsk.net>
Reported-by: Sebastien Dufour <sebastien.dufour@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
For example if we get bug reports with similar error states and
suspend count is always 1, that might lead the Sherlocks to
right general direction.
Suggested-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Just to be sure...
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This got lost when we shuffled around our internal branch and
GEN7_FEATURES macro. There were no HW changes to support FBC, so we just
need to set the flag.
v2: Don't allow FBC for any pipe but A on platforms with DDI. (Paulo)
Cc: Daisy Sun <daisy.sun@intel.com>
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The power domains framework is internal to the i915 driver, so pass
drm_i915_private instead of drm_device to its functions.
Also remove a dangling intel_set_power_well() declaration.
No functional change.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
A check of rps/rc6 state after i915_reset determined that the ring
MAX_IDLE registers were returned to their hardware defaults and that
the GEN6_PMIMR register was set to mask all interrupts. This change
restores those values to their pre-reset states by re-initializing
rps/rc6 in i915_reset. A full re-initialization was opted for versus
a targeted set of restore operations for simplicity and maintain-
ability. Note that the re-initialization is not done for Ironlake,
due to a past comment that it causes problems.
Also updated the rps initialization sequence to preserve existing
min/max values in the case of a re-init. We assume the values were
validated upon being set and do not do further range checking. The
debugfs interface for changing min/max was updated with range
checking to ensure this condition (already present in sysfs
interface).
v2: fix rps logging to output hw_max and hw_min, not rps.max_delay
and rps.min_delay which don't strictly represent hardware limits.
Add igt testcase to signed-off-by section.
Testcase: igt/pm_rps/reset
Signed-off-by: Jeff McGee <jeff.mcgee@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
RFCv2: Reorganize array indexing so that full offsets can be used as
is. It makes grepping for registers in i915_reg.h much easier. Also
move offset arrays to intel_device_info.
v1: Fixed offsets for VLV, proper eDP handling
v2: Fixed BCLRPAT, PIPESRC, PIPECONF and DSP* macros.
v3: Added EDP pipe comment, removed redundant offset arrays for
MSA_MISC and DDI_FUNC_CTL.
v4: Rename patch and report object size increase.
v5: Change location of commas, add PIPE_EDP into enum pipe
v6: Insert PIPE_EDP_OFFSET into pipe offset array
v7: Set I915_MAX_PIPES back to 3, change more registers accessors
to use the new macros, get rid of _PIPE_INC and add dev_priv
as a parameter where required by the new macros.
Upcoming hardware will not have the various display pipe register
ranges evenly spaced in memory. Change register address calculations
into array lookups.
Tested on SNB, VLV, IVB, Gen2 and HSW w/eDP.
I left the UMS cruft untouched.
Size differences:
text data bss dec hex filename
596431 4634 56 601121 92c21 i915.ko (new)
593199 4634 56 597889 91f81 i915.ko (old)
Signed-off-by: Antti Koskipaa <antti.koskipaa@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Tested-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
With 20+ module parameters, I think referring to them via a struct
improves clarity over just having a bunch of globals. While at it, move
the parameter initialization and definitions into a new file
i915_params.c to reduce clutter in i915_drv.c.
Apart from the ill-named i915_enable_rc6, i915_enable_fbc and
i915_enable_ppgtt parameters, for which we lose the "i915_" prefix
internally, the module parameters now look the same both on the kernel
command line and in code. For example, "i915.modeset".
The downsides of the change are losing static on a couple of variables
and not having the initialization and module_param_named() right next to
each other. On the other hand, all module parameters are now defined in
one place at i915_params.c. Plus you can do this to find all module
parameter references:
$ git grep "i915\." -- drivers/gpu/drm/i915
v2:
- move the definitions into a new file
- s/i915_params/i915/
- make i915_try_reset i915.reset, for consistency
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Because whatever.*
* This should contain a fairly long list of issues and still
unresolved resgressions, but I didn't really get a vote.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
It's unused, and nowadays specifying unknown parameters no longer
prevents modules from being loaded.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Currently we're doing the reset handling a bit late, and we're doing
it both in the driver load code and on resume. This makes it unusable
for e.g. resetting the panel power sequence state like Paulo wants to.
Instead of adding yet another single-use callback shuffle things
around:
- Output handling code is responsible to reset/init all state on its
own at driver load time.
- We call the reset functions much earlier, before we start using any
of the modeset code.
Compared to Paulo's new ->resume callback the only difference in
placement is that ->reset is still called without dev->struct_mutex
held. Which is imo a feature.
v2: Rebase on top of the now merge dinq.
Cc: Paulo Zanoni <przanoni@gmail.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The opregion notification for runtime suspend is currently D1, not D3.
Signed-off-by: Kristen Carlson Accardi <kristen@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
It ought to work ok in 3.14. We have some fun stuff coming after that,
but all the basics are in place now and seem relatively stable.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Acked by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
A couple patches in the upcoming rework of semaphores will break if
semaphores are toggled by the user at various times. Since the code
cleanups there seem to be an overall win, and toggling semaphores at
runtime is not a terribly useful thing to do, simply make the module
parameter read-only.
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
drm-intel-next-2014-01-10:
- final bits for runtime D3 on Haswell from Paul (now enabled fully)
- parse the backlight modulation freq information in the VBT from Jani
(but not yet used)
- more watermark improvements from Ville for ilk-ivb and bdw
- bugfixes for fastboot from Jesse
- watermark fix for i830M (but not yet everything)
- vlv vga hotplug w/a (Imre)
- piles of other small improvements, cleanups and fixes all over
Note that the pull request includes a backmerge of the last drm-fixes
pulled into Linus' tree - things where getting a bit too messy. So the
shortlog also contains a bunch of patches from Linus tree. Please yell if
you want me to frob it for you a bit.
* 'drm-intel-next' of git://people.freedesktop.org/~danvet/drm-intel: (609 commits)
drm/i915/bdw: make sure south port interrupts are enabled properly v2
drm/i915: Include more information in disabled hotplug interrupt warning
drm/i915: Only complain about a rogue hotplug IRQ after disabling
drm/i915: Only WARN about a stuck hotplug irq ONCE
drm/i915: s/hotplugt_status_gen4/hotplug_status_g4x/
Conflicts are getting out of hand, and now we have to shuffle even
more in -next which was also shuffled in -fixes (the call for
drm_mode_config_reset needs to move yet again).
So do a proper backmerge. I wanted to wait with this for the 3.13
relaese, but alas let's just do this now.
Conflicts:
drivers/gpu/drm/i915/i915_reg.h
drivers/gpu/drm/i915/intel_ddi.c
drivers/gpu/drm/i915/intel_display.c
drivers/gpu/drm/i915/intel_pm.c
Besides the conflict around the forcewake get/put (where we chaged the
called function in -fixes and added a new parameter in -next) code all
the current conflicts are of the adjacent lines changed type.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
- fbc1 improvements from Ville (pre-gm45).
- vlv forcewake improvements from Deepak S.
- Some corner-cases fixes from Mika for the context hang stat code.
- pc8 improvements and prep work for runtime D3 from Paulo, almost ready for
primetime.
- gen2 dpll fixes from Ville.
- DSI improvements from Shobhit Kumar.
- A few smaller fixes and improvements all over.
[airlied: intel_ddi.c conflict fixed up]
* tag 'drm-intel-next-2013-12-13' of git://people.freedesktop.org/~danvet/drm-intel: (61 commits)
drm/i915/bdw: Implement ff workarounds
drm/i915/bdw: Force all Data Cache Data Port access to be Non-Coherent
drm/i915/bdw: Don't use forcewake needlessly
drm/i915: Clear out old GT FIFO errors in intel_uncore_early_sanitize()
drm/i915: dont call irq_put when irq test is on
drm/i915: Rework the FBC interval/stall stuff a bit
drm/i915: Enable FBC for all mobile gen2 and gen3 platforms
drm/i915: FBC_CONTROL2 is gen4 only
drm/i915: Gen2 FBC1 CFB pitch wants 32B units
drm/i915: split intel_ddi_pll_mode_set in 2 pieces
drm/i915: Fix timeout with missed interrupts in __wait_seqno
drm/i915: touch VGA MSR after we enable the power well
drm/i915: extract hsw_power_well_post_{enable, disable}
drm/i915: remove i915_disable_vga_mem declaration
drm/i915: Parametrize the dphy and other spec specific parameters
drm/i915: Remove redundant DSI PLL enabling
drm/i915: Reorganize the DSI enable/disable sequence
drm/i915: Try harder to get best m, n, p values with minimal error
drm/i915: Compute dsi_clk from pixel clock
drm/i915: Use FLISDSI interface for band gap reset
...
Conflicts:
drivers/gpu/drm/i915/intel_ddi.c
As with processes which run on the CPU, the goal of multiple VMs is to
provide process isolation. Specific to GEN, there is also the ability to
map more objects per process (2GB each instead of 2Gb-2k total).
For the most part, all the pipes have been laid, and all we need to do
is remove asserts and actually start changing address spaces with the
context switch. Since prior to this we've converted the setting of the
page tables to a streamed version, this is quite easy.
One important thing to point out (since it'd been hotly contested) is
that with this patch, every context created will have it's own address
space (provided the HW can do it).
v2: Disable BDW on rebase
NOTE: I tried to make this commit as small as possible. I needed one
place where I could "turn everything on" and that is here. It could be
split into finer commits, but I didn't really see much point.
Cc: Eric Anholt <eric@anholt.net>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
I need the tricky do_switch fix before I can merge the final piece of
the ppgtt enabling puzzle. Otherwise the conflict will be a real pain
to resolve since the do_switch hunk from -fixes must be placed at the
exact right place within a hunk in the next patch.
Conflicts:
drivers/gpu/drm/i915/i915_gem_context.c
drivers/gpu/drm/i915/i915_gem_execbuffer.c
drivers/gpu/drm/i915/intel_display.c
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Only the two intel drivers need this and they can easily check for
working agp support in their driver ->load callbacks.
This is the only reason why agp initialization could fail, so allows
us to rip out a bit of error handling code in the next patch.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@redhat.com>
- some more ppgtt prep patches from Ben
- a few fbc fixes from Ville
- power well rework from Imre
- vlv forcewake improvements from Deepak S, Ville and Jesse
- a few smaller things all over
[airlied: fixup forwcewake conflict]
* tag 'drm-intel-next-2013-11-29' of git://people.freedesktop.org/~danvet/drm-intel: (97 commits)
drm/i915: Fix port name in vlv_wait_port_ready() timeout warning
drm/i915: Return a drm_mode_status enum in the mode_valid vfuncs
drm/i915: add intel_display_power_enabled_sw() for use in atomic ctx
drm/i915: drop DRM_ERROR in intel_fbdev init
drm/i915/vlv: use parallel context restore when coming out of RC6
drm/i915/vlv: use a lower RC6 timeout on VLV
drm/i915/sdvo: Fix up debug output to not split lines
drm/i915: make sparse happy for the new vlv mmio read function
drm/i915: drop the right force-wake engine in the vlv mmio funcs
drm/i915: Fix GT wake FIFO free entries for VLV
drm/i915: Report all GTFIFODBG errors
drm/i915: Enabling DebugFS for valleyview forcewake counts
drm/i915/vlv: Valleyview support for forcewake Individual power wells.
drm/i915: Add power well arguments to force wake routines.
drm/i915: Do not attempt to re-enable an unconnected primary plane
drm/i915: add a debugfs entry for power domain info
drm/i915: add a default always-on power well
drm/i915: don't do BDW/HSW specific powerdomains init on other platforms
drm/i915: protect HSW power well check with IS_HASWELL in redisable_vga
drm/i915: use IS_HASWELL/BROADWELL instead of HAS_POWER_WELL
...
Conflicts:
drivers/gpu/drm/i915/intel_display.c
Noticed while reviewing a patch and couldn't resist the OCD.
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
So we'll get a fault when someone tries to access the mmap, then we'll
wake up from D3.
v2: - Rebase
v3: - Use gtt active/inactive
Testcase: igt/pm_pc8/gem-mmap-gtt
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
[danvet: Add comment + WARN as discussed with Paulo on irc.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The hangcheck function requires the hardware to be working, and if
we're suspending we're going to put the HW in D3 state.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
All mobile gen2 and gen3 chipsets should have FBC1, and the code
should now handle them all. So just set has_fbc=true for all such
chipsets.
Note that fbc is still disabled by default for now.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Now that we are actually setting the device to the D3 state, we should
issue the notification.
The opregion spec says we should send the message before the adapter
is about to be placed in a lower power state, and after the adapter is
placed in a higher power state.
Jani originally wrote a similar patch for PC8, but then we discovered
that we were not really changing the PCI D states when
enabling/disabling PC8, so we had to postpone his patch.
v2: - Improve commit message, explaining the expected state.
v3: - Rebase.
Cc: Jani Nikula <jani.nikula@intel.com>
Credits-to: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@gmail.com> (v2)
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This patch adds the initial infrastructure to allow a Runtime PM
implementation that sets the device to its D3 state. The patch just
adds the necessary callbacks and the initial infrastructure.
We still don't have any platform that actually uses this
infrastructure, we still don't call get/put in all the places we need
to, and we don't have any function to save/restore the state of the
registers. This is not a problem since no platform uses the code added
by this patch. We have a few people simultaneously working on runtime
PM, so this initial code could help everybody make their plans.
V2: - Move some functions to intel_pm.c
- Remove useless pm_runtime_allow() call at init
- Remove useless pm_runtime_mark_last_busy() call at get
- Use pm_runtime_get_sync() instead of 2 calls
- Add a WARN to check if we're really awake
V3: - Rebase.
V4: - Don't need to call pci_{save,restore}_state and
pci_set_power_sate, since they're already called by the PCI
layer
- Remove wrong pm_runtime_enable() call at init_runtime_pm
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We call intel_modeset_setup_hw_state() along two paths, driver
load/resume and after a lid event notification. During initialisation of
the driver, it is imperative that we reset the config state. This
correctly sets up the initial connector statuses and prepares the
hardware for a thorough probing. However, during a lid event, we only
want to undo the damage caused by the bios by resetting our last known
mode. In this cirumstance, we do not want to clobber our desired state.
In order to try and keep sanity between the config state and our own
tracking, do the drm_mode_config_reset() first along the load/resume
paths before reading out the hw state and apply any definite known
corrections.
v2: "As discussed on irc I don't think we should force the connector
state to anything here: Imo connector->status should reflect what we
believe to be the true output connection state, whereas connector->encoder
reflects whether this connector is wired up to a pipe. And since we no
longer reject modeset on disconnected connectors and never nuked the pipe
if the connector gets disconnected there's no reason for that - such policy
is userspace's job.
This regression has been introduced in
commit 2e9388923e
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Thu Oct 11 20:08:24 2012 +0200
drm/i915/crt: explicitly set up HOTPLUG_BITS on resume"
so sayeth Daniel.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: stable@vger.kernel.org (v3.8 and later)
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This is just a theoretical issue, but we need to do this to prevent the
WARN in pipe_from_connector at suspend time.
This regression has been introduce in
commit 7bd688cd66
Author: Jani Nikula <jani.nikula@intel.com>
Date: Fri Nov 8 16:48:56 2013 +0200
drm/i915: handle backlight through chip specific functions
https://bugs.freedesktop.org/show_bug.cgi?id=71978
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This would have never worked.
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Oops, makes testing early boot failures in i915.ko a bit more pain, so
let's fix it.
v2: We already have a bit of static storage to track this (Chris).
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Tested-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
At least since SNB (perhaps even earlier) even the desktop parts
should have FBC.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Pull in Jani's backlight rework branch. This was merged through a
separate branch to be able to sort out the Broadwell conflicts
properly before pulling it into the main development branch.
Conflicts:
drivers/gpu/drm/i915/intel_display.c
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
It's been 5 years since kms support was merged and roughly 4 years
since UMS support was ripped out from userspace drivers.
Thus far it's not been a big burden to keep the ums paths alive, and
we've made some good progress in better separating it from the kms
code by sprinkling DRIVER_MODESET checks all over the place.
But now that the drm demidlayering is within reach this changes. I
want to make the driver loading code more robust using devres.c and
other cool tricks. But that doesn't work with ums due to the
shadow-attach trick. Which means we either
a) need to split out a complete ums codebase like radeon has
b) kill it for good.
The 2nd option is obviously much less work than the first, so I think
it's time to test the waters and see how many people out there still
use ums.
I've decided that silently failing to initialize the driver (and not
e.g. failing to load the module) is the right thing. That way we
should only get reports from users that actually care about some ums
features (like accelerated gl or support for secondary outputs).
Everyone else will just fall back to the vesa X driver.
For developers there's a small info level dmesg output.
The plan is to drop this Kconfig option after 3.16 (so gives us 2 full
releases) and then start killing code for real 2-3 releases
afterwards. That should be more than enough time for users to pipe up.
Of course if anyone does we need to revisit this plan and maybe go
with option a) above.
Also enable the KMS support by default in Kconfig and polish the help
texts a bit.
v2: Add the missing hunk of actual code changes. Oops. (Ville)
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Dave Airlie <airlied@gmail.com>
Acked-by: Dave Airlie <airlied@gmail.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Thus far we've tried to carefully work around the fact that old
userspace relied on the AGP-backed legacy buffer mapping ioctls for a
bit too long. But it's really horribly, and now some new users for it
started to show up again:
http://www.mail-archive.com/mesa-dev@lists.freedesktop.org/msg45547.html
This uses drmAgpSize to figure out the GTT size, which is both the
wrong thing to inquire and also might force us to keep this crap
around for another few years.
So I want to stop this particular zombie from raising ever again. Now
it's only been 4 years since XvMC was fixed for gen3, so a bit early
by the usual rules. But since Linus explicitly said that an ABI
breakage only counts if someone actually observes it I want to tempt
fate an accelarate the demise of AGP.
We probably need to wait 2-3 kernel releases with this shipping until
we go on a killing spree code-wise.
v2: Remove intel_agp_enabled since it's unused (Ville).
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Dave Airlie <airlied@gmail.com>
Acked-by: Dave Airlie <airlied@gmail.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Most platforms din't hit this condition, but if we want to allow
building without agp we should also make this allowed on gen3.
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We don't want any ERROR for simulated gpu hangs, otoh printing the
error code when the reset failed for real should be interesting.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=71333
lu hua <huax.lu@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We only depend on the intel-gtt module for GTT frobbign on older gens.
The intel_agp module is optional, except for UMS and some old XvMC
userland on gen3. So make AGP support optional. As before, we will
fail the i915 init for UMS and gen3 KMS the same as before if
intel_agp isn't around.
intel-gtt.c is left with a somewhat ugly ifdef mess, but I'm going
to save that for a later cleaning.
At least my gen2 still works with the patch and CONFIG_AGP=n.
v2: Make i915 depend on X86 and PCI, and intel-gtt depend on PCI
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Early platforms use the same PCH as HSW, and to avoid triggering the
!ULT, and !HSW warnings, simply put it first in the search.
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We've done insufficient testing on them thus far, so keep them disabled
until we do test.
v2: Use WARN when not enabling preliminary HW support as this should
only be disabled for that case.
v3: Rip out the now useless (and really noisy) DRM_INFO output.
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Reviewed-by: Jesse Barnes <jbarnes@virtuosugeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The platforms we currently have all have LPT LP on them. As such, we
have no way to identify the new WPT PCH that will ship with Broadwell.
NOTE: For all purposes relevant to the driver that this point, LPT and
WPT are equivalent. Therefore there should be no need to actually change
this for some time.
v2: Don't assign dev_priv->num_pch_pll any more.
v3: Rebase on top of the PCH detection changes for virtualized
enviroments.
v4: Wrote commit message
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com> (v1)
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch> (v3)
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
v2: Rebase (Paulo Zanoni)
v3: Rebase on top of num_pipes having moved to intel_device_info.
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com> (v1)
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com> (v2)
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
v2: Squash in "drm/i915/bdw: Add BDW to the HAS_DDI check" as
suggested by Damien.
v3: Squash in VEBOX enabling from Zhao Yakui <yakui.zhao@intel.com>
v4: Rebase on top of Jesse's patch to extract all pci ids to
include/drm/i915_pciids.h.
v4: Replace Halo by its marketing moniker Iris. Requested by Ben.
v5: Switch from info->has*ring to info->ring_mask.
v6: Add 0x16X2 variant (which is newer than this patch)
Rename to use new naming scheme (Chris)
Remove Simulator PCI ids. These snuck in during rebase (Chris)
v7: Fix poor sed job from v6
Make the desktop variants use the desktop macro (Rebase error). Notice
that this makes no functional difference - it's just confusing.
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
v2: Fixed the botched locking on init_hw failure in i915_reset (Ville)
Call cleanup_ringbuffer on failed context create in init_hw (Ville)
v3: Add dev argument ti clean_ringbuffer
Reviewed-by: Kenneth Graunke <kenneth@whitecape.org>
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
I want to merge in the new Broadwell support as a late hw enabling
pull request. But since the internal branch was based upon our
drm-intel-nightly integration branch I need to resolve all the
oustanding conflicts in drm/i915 with a backmerge to make the 60+
patches apply properly.
We'll propably have some fun because Linus will come up with a
slightly different merge solution.
Conflicts:
drivers/gpu/drm/i915/i915_dma.c
drivers/gpu/drm/i915/i915_drv.c
drivers/gpu/drm/i915/intel_crt.c
drivers/gpu/drm/i915/intel_ddi.c
drivers/gpu/drm/i915/intel_display.c
drivers/gpu/drm/i915/intel_dp.c
drivers/gpu/drm/i915/intel_drv.h
All rather simple adjacent lines changed or partial backports from
-next to -fixes, with the exception of the thaw code in i915_dma.c.
That one needed a bit of shuffling to restore the intent.
Oh and the massive header file reordering in intel_drv.h is a bit
trouble. But not much.
v2: Also don't forget the fixup for the silent conflict that results
in compile fail ...
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Similarly rename the other related functions in the power domain
interface.
Higher level driver code calling these functions knows only about power
domains, not the underlying power wells which may be different on
different platforms. Also these functions really init/cleanup/resume
power domains and only through that all related power wells, so rename
them accordingly.
Note that I left i915_{request,release}_power_well as is, since that
really changes the state only of a single power well (and is HSW
specific). It should also get a better name once we make it more
generic by controlling things through a new audio power domain.
v4:
- use intel prefix instead of i915 everywhere (Paulo)
- use a $prefix_$block_$action format (Daniel)
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Currently we make sure that all power domains are enabled during driver
init and turn off unneded ones only after the first modeset. Similarly
during suspend we enable all power domains, which will remain on through
the following resume until the first modeset.
This logic is supported by intel_set_power_well() in the power domain
framework. It would be nice to simplify the API, so that we only have
get/put functions and make it more explicit on the higher level how this
"power well on during init" logic works. This will make it also easier
if in the future we want to shorten the time the power wells are on.
For this add a new device private flag tracking whether we have the
power wells on because of init/suspend and use only
intel_display_power_get()/put(). As nothing else uses
intel_set_power_well() we can remove it.
This also fixes
commit 6efdf354dd
Author: Imre Deak <imre.deak@intel.com>
Date: Wed Oct 16 17:25:52 2013 +0300
drm/i915: enable only the needed power domains during modeset
where removing intel_set_power_well() resulted in not releasing the
reference on the power well that was taken during init and thus leaving
the power well on all the time. Regression reported by Paulo.
v2:
- move the init_power_on flag to the power_domains struct (Daniel)
v3:
- add note about this being a regression fix too (Paulo)
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Once the machine gets to a certain point in the suspend process, we
expect the GPU to be idle. If it is not, we might corrupt memory.
Empirically (with an early version of this patch) we have seen this is
not the case. We cannot currently explain why the latent GPU writes
occur.
In the technical sense, this patch is a workaround in that we have an
issue we can't explain, and the patch indirectly solves the issue.
However, it's really better than a workaround because we understand why
it works, and it really should be a safe thing to do in all cases.
The noticeable effect other than the debug messages would be an increase
in the suspend time. I have not measure how expensive it actually is.
I think it would be good to spend further time to root cause why we're
seeing these latent writes, but it shouldn't preclude preventing the
fallout.
NOTE: It should be safe (and makes some sense IMO) to also keep the
VALID bit unset on resume when we clear_range(). I've opted not to do
this as properly clearing those bits at some later point would be extra
work.
v2: Fix bugzilla link
Bugzilla: http://bugs.freedesktop.org/show_bug.cgi?id=65496
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=59321
Tested-by: Takashi Iwai <tiwai@suse.de>
Tested-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Tested-By: Todd Previte <tprevite@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We have two once very similar functions, i915_gpu_idle() and
i915_gem_idle(). The former is used as the lower level operation to
flush work on the GPU, whereas the latter is the high level interface to
flush the GEM bookkeeping in addition to flushing the GPU. As such
i915_gem_idle() also clears out the request and activity lists and
cancels the delayed work. This is what we need for unloading the driver,
unfortunately we called i915_gpu_idle() instead.
In the process, make sure that when cancelling the delayed work and
timer, which is synchronous, that we do not hold any locks to prevent a
deadlock if the work item is already waiting upon the mutex. This
requires us to push the mutex down from the caller to i915_gem_idle().
v2: s/i915_gem_idle/i915_gem_suspend/
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=70334
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Tested-by: xunx.fang@intel.com
[danvet: Only set ums.suspended for !kms as discussed earlier. Chris
noticed that this slipped through.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
I've sent this patch several times for various reasons. It essentially
cleans up a lot of code where we need to do something per ring, and want
to query whether or not the ring exists on that hardware.
It has various uses coming up, but for now it shouldn't be too
offensive.
v2: Big conflict resolution on Damien's DEV_INFO_FOR_EACH stuff
v3: Resolved vebox addition
v4: Rebased after months of disuse. Also made failed ringbuffer init
cleaner.
v5: Remove the init cleaner from v4. There is a better way to do it.
(Chris)
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
I had this lying around from he original PPGTT series, and thought we
might try to get it in by itself.
It's convenient to just call i915_gem_init_hw at reset because we'll be
adding new things to that function, and having just one function to call
instead of reimplementing it in two places is nice.
In order to accommodate we cleanup ringbuffers in order to bring them
back up cleanly. Optionally, we could also teardown/re initialize the
default context but this was causing some problems on reset which I
wasn't able to fully debug, and is unnecessary with the previous context
init/enable split.
This essentially reverts:
commit 8e88a2bd59
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Tue Jun 19 18:40:00 2012 +0200
drm/i915: don't call modeset_init_hw in i915_reset
It seems to work for me on ILK now. Perhaps it's due to:
commit 8a5c2ae753
Author: Jesse Barnes <jbarnes@virtuousgeek.org>
Date: Thu Mar 28 13:57:19 2013 -0700
drm/i915: fix ILK GPU reset for render
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Now that MMIO has been split up into gen specific functions it is
obvious when HAS_FPGA_DBG_UNCLAIMED, HAS_FORCE_WAKE are needed. As such,
we can remove this extraneous condition.
As a result of this, as well as previously existing function pointers
for forcewake, we no longer need the has_force_wake member in the device
specific data structure.
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The conflict in intel_drv.h tripped me up a bit since a patch in dinq
moves all the functions around, but another one in drm-next removes a
single function. So I'ev figured backing this into a backmerge would
be good.
i915_dma.c is just adjacent lines changed, nothing nefarious there.
Conflicts:
drivers/gpu/drm/i915/i915_dma.c
drivers/gpu/drm/i915/intel_drv.h
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
All drivers embed gem-objects into their own buffer objects. There is no
reason to keep drm_gem_object_alloc(), gem->driver_private and
->gem_init_object() anymore.
New drivers are highly encouraged to do the same. There is no benefit in
allocating gem-objects separately.
Cc: Dave Airlie <airlied@gmail.com>
Cc: Alex Deucher <alexdeucher@gmail.com>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Jerome Glisse <jglisse@redhat.com>
Cc: Rob Clark <robdclark@gmail.com>
Cc: Inki Dae <inki.dae@samsung.com>
Cc: Ben Skeggs <skeggsb@gmail.com>
Cc: Patrik Jakobsson <patrik.r.jakobsson@gmail.com>
Signed-off-by: David Herrmann <dh.herrmann@gmail.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Call intel_uncore_early_sanitize() first thing during resume to prevent
stale BIOS leftovers from being reported as unclaimed register access.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Jani Nikula
Animesh Manna
Alex Dai
Robert Beckett
Daniel Vetter
Ville Syrjälä
Linus Torvalds
Maarten Lankhorst
Imre Deak
Paulo Zanoni
Peter Zijlstra
Damien Lespiau
Chris Wilson
Dave Airlie
Peter Antoine
Jesse Barnes
Suketu Shah
Daisy Sun
Deepak S
Andreas Ruprecht
Takashi Iwai
Matt Roper
Mika Kuoppala
Rodrigo Vivi
Thomas Hellstrom
Satheeshakrishna M
David Herrmann
McAulay, Alistair
Oscar Mateo
Sagar Kamble
Borun Fu
Kristen Carlson Accardi
Rodrigo Vivi
Rafael Barbalho
Zhao Yakui
Ben Widawsky
Jeff McGee
Antti Koskipaa
Ben Widawsky