Since the tag_8021q tagger is software-defined, it has no means by
itself for retrieving hardware timestamps of PTP event messages.
Because we do want to support PTP on ocelot even with tag_8021q, we need
to use the CPU port module for that. The RX timestamp is present in the
Extraction Frame Header. And because we can't use NPI mode which redirects
the CPU queues to an "external CPU" (meaning the ARM CPU running Linux),
then we need to poll the CPU port module through the MMIO registers to
retrieve TX and RX timestamps.
Sadly, on NXP LS1028A, the Felix switch was integrated into the SoC
without wiring the extraction IRQ line to the ARM GIC. So, if we want to
be notified of any PTP packets received on the CPU port module, we have
a problem.
There is a possible workaround, which is to use the Ethernet CPU port as
a notification channel that packets are available on the CPU port module
as well. When a PTP packet is received by the DSA tagger (without timestamp,
of course), we go to the CPU extraction queues, poll for it there, then
we drop the original Ethernet packet and masquerade the packet retrieved
over MMIO (plus the timestamp) as the original when we inject it up the
stack.
Create a quirk in struct felix is selected by the Felix driver (but not
by Seville, since that doesn't support PTP at all). We want to do this
such that the workaround is minimally invasive for future switches that
don't require this workaround.
The only traffic for which we need timestamps is PTP traffic, so add a
redirection rule to the CPU port module for this. Currently we only have
the need for PTP over L2, so redirection rules for UDP ports 319 and 320
are TBD for now.
Note that for the workaround of matching of PTP-over-Ethernet-port with
PTP-over-MMIO queues to work properly, both channels need to be
absolutely lossless. There are two parts to achieving that:
- We keep flow control enabled on the tag_8021q CPU port
- We put the DSA master interface in promiscuous mode, so it will never
drop a PTP frame (for the profiles we are interested in, these are
sent to the multicast MAC addresses of 01-80-c2-00-00-0e and
01-1b-19-00-00-00).
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ocelot tagger is a hot mess currently, it relies on memory
initialized by the attached driver for basic frame transmission.
This is against all that DSA tagging protocols stand for, which is that
the transmission and reception of a DSA-tagged frame, the data path,
should be independent from the switch control path, because the tag
protocol is in principle hot-pluggable and reusable across switches
(even if in practice it wasn't until very recently). But if another
driver like dsa_loop wants to make use of tag_ocelot, it couldn't.
This was done to have common code between Felix and Ocelot, which have
one bit difference in the frame header format. Quoting from commit
67c2404922 ("net: dsa: felix: create a template for the DSA tags on
xmit"):
Other alternatives have been analyzed, such as:
- Create a separate tag_seville.c: too much code duplication for just 1
bit field difference.
- Create a separate DSA_TAG_PROTO_SEVILLE under tag_ocelot.c, just like
tag_brcm.c, which would have a separate .xmit function. Again, too
much code duplication for just 1 bit field difference.
- Allocate the template from the init function of the tag_ocelot.c
module, instead of from the driver: couldn't figure out a method of
accessing the correct port template corresponding to the correct
tagger in the .xmit function.
The really interesting part is that Seville should have had its own
tagging protocol defined - it is not compatible on the wire with Ocelot,
even for that single bit. In principle, a packet generated by
DSA_TAG_PROTO_OCELOT when booted on NXP LS1028A would look in a certain
way, but when booted on NXP T1040 it would look differently. The reverse
is also true: a packet generated by a Seville switch would be
interpreted incorrectly by Wireshark if it was told it was generated by
an Ocelot switch.
Actually things are a bit more nuanced. If we concentrate only on the
DSA tag, what I said above is true, but Ocelot/Seville also support an
optional DSA tag prefix, which can be short or long, and it is possible
to distinguish the two taggers based on an integer constant put in that
prefix. Nonetheless, creating a separate tagger is still justified,
since the tag prefix is optional, and without it, there is again no way
to distinguish.
Claiming backwards binary compatibility is a bit more tough, since I've
already changed the format of tag_ocelot once, in commit 5124197ce5
("net: dsa: tag_ocelot: use a short prefix on both ingress and egress").
Therefore I am not very concerned with treating this as a bugfix and
backporting it to stable kernels (which would be another mess due to the
fact that there would be lots of conflicts with the other DSA_TAG_PROTO*
definitions). It's just simpler to say that the string values of the
taggers have ABI value starting with kernel 5.12, which will be when the
changing of tag protocol via /sys/class/net/<dsa-master>/dsa/tagging
goes live.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is one place where we cannot avoid accessing driver data, and that
is 2-step PTP TX timestamping, since the switch wants us to provide a
timestamp request ID through the injection header, which naturally must
come from a sequence number kept by the driver (it is generated by the
.port_txtstamp method prior to the tagger's xmit).
However, since other drivers like dsa_loop do not claim PTP support
anyway, the DSA_SKB_CB(skb)->clone will always be NULL anyway, so if we
move all PTP-related dereferences of struct ocelot and struct ocelot_port
into a separate function, we can effectively ensure that this is dead
code when the ocelot tagger is attached to non-ocelot switches, and the
stateful portion of the tagger is more self-contained.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Injection Frame Header and Extraction Frame Header that the switch
prepends to frames over the NPI port is also prepended to frames
delivered over the CPU port module's queues.
Let's unify the handling of the frame headers by making the ocelot
driver call some helpers exported by the DSA tagger. Among other things,
this allows us to get rid of the strange cpu_to_be32 when transmitting
the Injection Frame Header on ocelot, since the packing API uses
network byte order natively (when "quirks" is 0).
The comments above ocelot_gen_ifh talk about setting pop_cnt to 3, and
the cpu extraction queue mask to something, but the code doesn't do it,
so we don't do it either.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Taggers should be written to do something valid irrespective of the
switch driver that they are attached to. This is even more true now,
because since the introduction of the .change_tag_protocol method, a
certain tagger is not necessarily strictly associated with a driver any
longer, and I would like to be able to test all taggers with dsa_loop in
the future.
In the case of ocelot, it needs to move the classified VLAN from the DSA
tag into the skb if the port is VLAN-aware. We can allow it to do that
by looking at the dp->vlan_filtering property, no need to invoke
structures which are specific to ocelot.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
napi_frags_finish() and napi_skb_finish() can only be called inside
NAPI Rx context, so we can feed NAPI cache with skbuff_heads that
got NAPI_MERGED_FREE verdict instead of immediate freeing.
Replace __kfree_skb() with __kfree_skb_defer() in napi_skb_finish()
and move napi_skb_free_stolen_head() to skbuff.c, so it can drop skbs
to NAPI cache.
As many drivers call napi_alloc_skb()/napi_get_frags() on their
receive path, this becomes especially useful.
Signed-off-by: Alexander Lobakin <alobakin@pm.me>
Signed-off-by: David S. Miller <davem@davemloft.net>
{,__}napi_alloc_skb() is mostly used either for optional non-linear
receive methods (usually controlled via Ethtool private flags and off
by default) and/or for Rx copybreaks.
Use __napi_build_skb() here for obtaining skbuff_heads from NAPI cache
instead of inplace allocations. This includes both kmalloc and page
frag paths.
Signed-off-by: Alexander Lobakin <alobakin@pm.me>
Signed-off-by: David S. Miller <davem@davemloft.net>
Reuse the old and forgotten SKB_ALLOC_NAPI to add an option to get
an skbuff_head from the NAPI cache instead of inplace allocation
inside __alloc_skb().
This implies that the function is called from softirq or BH-off
context, not for allocating a clone or from a distant node.
Cc: Alexander Duyck <alexander.duyck@gmail.com> # Simplified flags check
Signed-off-by: Alexander Lobakin <alobakin@pm.me>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of just bulk-flushing skbuff_heads queued up through
napi_consume_skb() or __kfree_skb_defer(), try to reuse them
on allocation path.
If the cache is empty on allocation, bulk-allocate the first
16 elements, which is more efficient than per-skb allocation.
If the cache is full on freeing, bulk-wipe the second half of
the cache (32 elements).
This also includes custom KASAN poisoning/unpoisoning to be
double sure there are no use-after-free cases.
To not change current behaviour, introduce a new function,
napi_build_skb(), to optionally use a new approach later
in drivers.
Note on selected bulk size, 16:
- this equals to XDP_BULK_QUEUE_SIZE, DEV_MAP_BULK_SIZE
and especially VETH_XDP_BATCH, which is also used to
bulk-allocate skbuff_heads and was tested on powerful
setups;
- this also showed the best performance in the actual
test series (from the array of {8, 16, 32}).
Suggested-by: Edward Cree <ecree.xilinx@gmail.com> # Divide on two halves
Suggested-by: Eric Dumazet <edumazet@google.com> # KASAN poisoning
Cc: Dmitry Vyukov <dvyukov@google.com> # Help with KASAN
Cc: Paolo Abeni <pabeni@redhat.com> # Reduced batch size
Signed-off-by: Alexander Lobakin <alobakin@pm.me>
Signed-off-by: David S. Miller <davem@davemloft.net>
NAPI cache structures will be used for allocating skbuff_heads,
so move their declarations a bit upper.
Signed-off-by: Alexander Lobakin <alobakin@pm.me>
Signed-off-by: David S. Miller <davem@davemloft.net>
This function isn't much needed as NAPI skb queue gets bulk-freed
anyway when there's no more room, and even may reduce the efficiency
of bulk operations.
It will be even less needed after reusing skb cache on allocation path,
so remove it and this way lighten network softirqs a bit.
Suggested-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Alexander Lobakin <alobakin@pm.me>
Signed-off-by: David S. Miller <davem@davemloft.net>
Just call __build_skb_around() instead of open-coding it.
Signed-off-by: Alexander Lobakin <alobakin@pm.me>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use unlikely() annotations for skbuff_head and data similarly to the
two other allocation functions and remove totally redundant goto.
Signed-off-by: Alexander Lobakin <alobakin@pm.me>
Signed-off-by: David S. Miller <davem@davemloft.net>
__build_skb_around() can never fail and always returns passed skb.
Make it return void to simplify and optimize the code.
Signed-off-by: Alexander Lobakin <alobakin@pm.me>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eversince the introduction of __kmalloc_reserve(), "ip" argument
hasn't been used. _RET_IP_ is embedded inside
kmalloc_node_track_caller().
Remove the redundant macro and rename the function after it.
Signed-off-by: Alexander Lobakin <alobakin@pm.me>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation before reusing several functions in all three skb
allocation variants, move __alloc_skb() next to the
__netdev_alloc_skb() and __napi_alloc_skb().
No functional changes.
Signed-off-by: Alexander Lobakin <alobakin@pm.me>
Signed-off-by: David S. Miller <davem@davemloft.net>
Both tcp_data_ready() and tcp_stream_is_readable() share the same logic.
Add tcp_epollin_ready() helper to avoid duplication.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Arjun Roy <arjunroy@google.com>
Cc: Wei Wang <weiwan@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are multiple ways in which a PORT_BRIDGE_FLAGS attribute can be
expressed by the bridge through switchdev, and not all of them can be
emulated by DSA mid-layer API at the same time.
One possible configuration is when the bridge offloads the port flags
using a mask that has a single bit set - therefore only one feature
should change. However, DSA currently groups together unicast and
multicast flooding in the .port_egress_floods method, which limits our
options when we try to add support for turning off broadcast flooding:
do we extend .port_egress_floods with a third parameter which b53 and
mv88e6xxx will ignore? But that means that the DSA layer, which
currently implements the PRE_BRIDGE_FLAGS attribute all by itself, will
see that .port_egress_floods is implemented, and will report that all 3
types of flooding are supported - not necessarily true.
Another configuration is when the user specifies more than one flag at
the same time, in the same netlink message. If we were to create one
individual function per offloadable bridge port flag, we would limit the
expressiveness of the switch driver of refusing certain combinations of
flag values. For example, a switch may not have an explicit knob for
flooding of unknown multicast, just for flooding in general. In that
case, the only correct thing to do is to allow changes to BR_FLOOD and
BR_MCAST_FLOOD in tandem, and never allow mismatched values. But having
a separate .port_set_unicast_flood and .port_set_multicast_flood would
not allow the driver to possibly reject that.
Also, DSA doesn't consider it necessary to inform the driver that a
SWITCHDEV_ATTR_ID_BRIDGE_MROUTER attribute was offloaded, because it
just calls .port_egress_floods for the CPU port. When we'll add support
for the plain SWITCHDEV_ATTR_ID_PORT_MROUTER, that will become a real
problem because the flood settings will need to be held statefully in
the DSA middle layer, otherwise changing the mrouter port attribute will
impact the flooding attribute. And that's _assuming_ that the underlying
hardware doesn't have anything else to do when a multicast router
attaches to a port than flood unknown traffic to it. If it does, there
will need to be a dedicated .port_set_mrouter anyway.
So we need to let the DSA drivers see the exact form that the bridge
passes this switchdev attribute in, otherwise we are standing in the
way. Therefore we also need to use this form of language when
communicating to the driver that it needs to configure its initial
(before bridge join) and final (after bridge leave) port flags.
The b53 and mv88e6xxx drivers are converted to the passthrough API and
their implementation of .port_egress_floods is split into two: a
function that configures unicast flooding and another for multicast.
The mv88e6xxx implementation is quite hairy, and it turns out that
the implementations of unknown unicast flooding are actually the same
for 6185 and for 6352:
behind the confusing names actually lie two individual bits:
NO_UNKNOWN_MC -> FLOOD_UC = 0x4 = BIT(2)
NO_UNKNOWN_UC -> FLOOD_MC = 0x8 = BIT(3)
so there was no reason to entangle them in the first place.
Whereas the 6185 writes to MV88E6185_PORT_CTL0_FORWARD_UNKNOWN of
PORT_CTL0, which has the exact same bit index. I have left the
implementations separate though, for the only reason that the names are
different enough to confuse me, since I am not able to double-check with
a user manual. The multicast flooding setting for 6185 is in a different
register than for 6352 though.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This switchdev attribute offers a counterproductive API for a driver
writer, because although br_switchdev_set_port_flag gets passed a
"flags" and a "mask", those are passed piecemeal to the driver, so while
the PRE_BRIDGE_FLAGS listener knows what changed because it has the
"mask", the BRIDGE_FLAGS listener doesn't, because it only has the final
value. But certain drivers can offload only certain combinations of
settings, like for example they cannot change unicast flooding
independently of multicast flooding - they must be both on or both off.
The way the information is passed to switchdev makes drivers not
expressive enough, and unable to reject this request ahead of time, in
the PRE_BRIDGE_FLAGS notifier, so they are forced to reject it during
the deferred BRIDGE_FLAGS attribute, where the rejection is currently
ignored.
This patch also changes drivers to make use of the "mask" field for edge
detection when possible.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For a DSA switch port operating in standalone mode, address learning
doesn't make much sense since that is a bridge function. In fact,
address learning even breaks setups such as this one:
+---------------------------------------------+
| |
| +-------------------+ |
| | br0 | send receive |
| +--------+-+--------+ +--------+ +--------+ |
| | | | | | | | | |
| | swp0 | | swp1 | | swp2 | | swp3 | |
| | | | | | | | | |
+-+--------+-+--------+-+--------+-+--------+-+
| ^ | ^
| | | |
| +-----------+ |
| |
+--------------------------------+
because if the switch has a single FDB (can offload a single bridge)
then source address learning on swp3 can "steal" the source MAC address
of swp2 from br0's FDB, because learning frames coming from swp2 will be
done twice: first on the swp1 ingress port, second on the swp3 ingress
port. So the hardware FDB will become out of sync with the software
bridge, and when swp2 tries to send one more packet towards swp1, the
ASIC will attempt to short-circuit the forwarding path and send it
directly to swp3 (since that's the last port it learned that address on),
which it obviously can't, because swp3 operates in standalone mode.
So DSA drivers operating in standalone mode should still configure a
list of bridge port flags even when they are standalone. Currently DSA
attempts to call dsa_port_bridge_flags with 0, which disables egress
flooding of unknown unicast and multicast, something which doesn't make
much sense. For the switches that implement .port_egress_floods - b53
and mv88e6xxx, it probably doesn't matter too much either, since they
can possibly inject traffic from the CPU into a standalone port,
regardless of MAC DA, even if egress flooding is turned off for that
port, but certainly not all DSA switches can do that - sja1105, for
example, can't. So it makes sense to use a better common default there,
such as "flood everything".
It should also be noted that what DSA calls "dsa_port_bridge_flags()"
is a degenerate name for just calling .port_egress_floods(), since
nothing else is implemented - not learning, in particular. But disabling
address learning, something that this driver is also coding up for, will
be supported by individual drivers once .port_egress_floods is replaced
with a more generic .port_bridge_flags.
Previous attempts to code up this logic have been in the common bridge
layer, but as pointed out by Ido Schimmel, there are corner cases that
are missed when doing that:
https://patchwork.kernel.org/project/netdevbpf/patch/20210209151936.97382-5-olteanv@gmail.com/
So, at least for now, let's leave DSA in charge of setting port flags
before and after the bridge join and leave.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For the netlink interface, propagate errors through extack rather than
simply printing them to the console. For the sysfs interface, we still
print to the console, but at least that's one layer higher than in
switchdev, which also allows us to silently ignore the offloading of
flags if that is ever needed in the future.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Acked-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If for example this command:
ip link set swp0 type bridge_slave flood off mcast_flood off learning off
succeeded at configuring BR_FLOOD and BR_MCAST_FLOOD but not at
BR_LEARNING, there would be no attempt to revert the partial state in
any way. Arguably, if the user changes more than one flag through the
same netlink command, this one _should_ be all or nothing, which means
it should be passed through switchdev as all or nothing.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Acked-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a struct switchdev_attr is notified through switchdev, there is no
way to report informational messages, unlike for struct switchdev_obj.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
the following command:
# tc filter add dev $h2 ingress protocol ip pref 1 handle 101 flower \
$tcflags dst_ip 192.0.2.2 ip_ttl 63 action drop
doesn't drop all IPv4 packets that match the configured TTL / destination
address. In particular, if "fragment offset" or "more fragments" have non
zero value in the IPv4 header, setting of FLOW_DISSECTOR_KEY_IP is simply
ignored. Fix this dissecting IPv4 TTL and TOS before fragment info; while
at it, add a selftest for tc flower's match on 'ip_ttl' that verifies the
correct behavior.
Fixes: 518d8a2e9b ("net/flow_dissector: add support for dissection of misc ip header fields")
Reported-by: Shuang Li <shuali@redhat.com>
Signed-off-by: Davide Caratti <dcaratti@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* more minstrel work from Felix to reduce the
probing overhead
* QoS for nl80211 control port frames
* STBC injection support
* and a couple of small fixes
-----BEGIN PGP SIGNATURE-----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=PXD5
-----END PGP SIGNATURE-----
Merge tag 'mac80211-next-for-net-next-2021-02-12' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
Johannes Berg says:
====================
Last set of updates:
* more minstrel work from Felix to reduce the
probing overhead
* QoS for nl80211 control port frames
* STBC injection support
* and a couple of small fixes
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
As udp_port_cfg struct changes its members with dependency on IPv6
configuration, the code in rxrpc should also check for IPv6.
Fixes: 1a9b86c9fd ("rxrpc: use udp tunnel APIs instead of open code in rxrpc_open_socket")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Vadim Fedorenko <vfedorenko@novek.ru>
Acked-by: David Howells <dhowells@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If a DDP broadcast packet is sent out to a non-gateway target, it is
also looped back. There is a potential for the loopback device to have a
longer hardware header length than the original target route's device,
which can result in the skb not being created with enough room for the
loopback device's hardware header. This patch fixes the issue by
determining that a loopback will be necessary prior to allocating the
skb, and if so, ensuring the skb has enough room.
This was discovered while testing a new driver that creates a LocalTalk
network interface (LTALK_HLEN = 1). It caused an skb_under_panic.
Signed-off-by: Doug Brown <doug@schmorgal.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow userspace (mptcpd) to subscribe to mptcp genl multicast events.
This implementation reuses the same event API as the mptcp kernel fork
to ease integration of existing tools, e.g. mptcpd.
Supported events include:
1. start and close of an mptcp connection
2. start and close of subflows (joins)
3. announce and withdrawals of addresses
4. subflow priority (backup/non-backup) change.
Reviewed-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Once event support is added this may need to allocate memory while msk
lock is held with softirqs disabled.
Not using lock_fast also allows to do the allocation with GFP_KERNEL.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pass the first/initial subflow to the existing functions so they can
pass this on to the notification handler that is added later in the
series.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In case mptcp socket is already dead the entire mptcp socket
will be freed. We can avoid the close check in this case.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When remote side closes a subflow we should schedule the worker to
dispose of the subflow in a timely manner.
Otherwise, SF_CLOSED event won't be generated until the mptcp
socket itself is closing or local side is closing another subflow.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Prepare for subflow close events:
When mptcp connection is torn down its enough to send the mptcp socket
close notification rather than a subflow close event for all of the
subflows followed by the mptcp close event.
This splits the helper: mptcp_close_ssk() will emit the close
notification, __mptcp_close_ssk will not.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allows to make some functions static and avoids acquire of the pm
spinlock in protocol.c.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The use-case for dropping the MTU check when TC-BPF does redirect to
ingress, is described by Eyal Birger in email[0]. The summary is the
ability to increase packet size (e.g. with IPv6 headers for NAT64) and
ingress redirect packet and let normal netstack fragment packet as needed.
[0] https://lore.kernel.org/netdev/CAHsH6Gug-hsLGHQ6N0wtixdOa85LDZ3HNRHVd0opR=19Qo4W4Q@mail.gmail.com/
V15:
- missing static for function declaration
V9:
- Make net_device "up" (IFF_UP) check explicit in skb_do_redirect
V4:
- Keep net_device "up" (IFF_UP) check.
- Adjustment to handle bpf_redirect_peer() helper
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: John Fastabend <john.fastabend@gmail.com>
Link: https://lore.kernel.org/bpf/161287790971.790810.11785274340154740591.stgit@firesoul
This BPF-helper bpf_check_mtu() works for both XDP and TC-BPF programs.
The SKB object is complex and the skb->len value (accessible from
BPF-prog) also include the length of any extra GRO/GSO segments, but
without taking into account that these GRO/GSO segments get added
transport (L4) and network (L3) headers before being transmitted. Thus,
this BPF-helper is created such that the BPF-programmer don't need to
handle these details in the BPF-prog.
The API is designed to help the BPF-programmer, that want to do packet
context size changes, which involves other helpers. These other helpers
usually does a delta size adjustment. This helper also support a delta
size (len_diff), which allow BPF-programmer to reuse arguments needed by
these other helpers, and perform the MTU check prior to doing any actual
size adjustment of the packet context.
It is on purpose, that we allow the len adjustment to become a negative
result, that will pass the MTU check. This might seem weird, but it's not
this helpers responsibility to "catch" wrong len_diff adjustments. Other
helpers will take care of these checks, if BPF-programmer chooses to do
actual size adjustment.
V14:
- Improve man-page desc of len_diff.
V13:
- Enforce flag BPF_MTU_CHK_SEGS cannot use len_diff.
V12:
- Simplify segment check that calls skb_gso_validate_network_len.
- Helpers should return long
V9:
- Use dev->hard_header_len (instead of ETH_HLEN)
- Annotate with unlikely req from Daniel
- Fix logic error using skb_gso_validate_network_len from Daniel
V6:
- Took John's advice and dropped BPF_MTU_CHK_RELAX
- Returned MTU is kept at L3-level (like fib_lookup)
V4: Lot of changes
- ifindex 0 now use current netdev for MTU lookup
- rename helper from bpf_mtu_check to bpf_check_mtu
- fix bug for GSO pkt length (as skb->len is total len)
- remove __bpf_len_adj_positive, simply allow negative len adj
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: John Fastabend <john.fastabend@gmail.com>
Link: https://lore.kernel.org/bpf/161287790461.790810.3429728639563297353.stgit@firesoul
The BPF-helpers for FIB lookup (bpf_xdp_fib_lookup and bpf_skb_fib_lookup)
can perform MTU check and return BPF_FIB_LKUP_RET_FRAG_NEEDED. The BPF-prog
don't know the MTU value that caused this rejection.
If the BPF-prog wants to implement PMTU (Path MTU Discovery) (rfc1191) it
need to know this MTU value for the ICMP packet.
Patch change lookup and result struct bpf_fib_lookup, to contain this MTU
value as output via a union with 'tot_len' as this is the value used for
the MTU lookup.
V5:
- Fixed uninit value spotted by Dan Carpenter.
- Name struct output member mtu_result
Reported-by: kernel test robot <lkp@intel.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: John Fastabend <john.fastabend@gmail.com>
Link: https://lore.kernel.org/bpf/161287789952.790810.13134700381067698781.stgit@firesoul
BPF end-user on Cilium slack-channel (Carlo Carraro) wants to use
bpf_fib_lookup for doing MTU-check, but *prior* to extending packet size,
by adjusting fib_params 'tot_len' with the packet length plus the expected
encap size. (Just like the bpf_check_mtu helper supports). He discovered
that for SKB ctx the param->tot_len was not used, instead skb->len was used
(via MTU check in is_skb_forwardable() that checks against netdev MTU).
Fix this by using fib_params 'tot_len' for MTU check. If not provided (e.g.
zero) then keep existing TC behaviour intact. Notice that 'tot_len' for MTU
check is done like XDP code-path, which checks against FIB-dst MTU.
V16:
- Revert V13 optimization, 2nd lookup is against egress/resulting netdev
V13:
- Only do ifindex lookup one time, calling dev_get_by_index_rcu().
V10:
- Use same method as XDP for 'tot_len' MTU check
Fixes: 4c79579b44 ("bpf: Change bpf_fib_lookup to return lookup status")
Reported-by: Carlo Carraro <colrack@gmail.com>
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Link: https://lore.kernel.org/bpf/161287789444.790810.15247494756551413508.stgit@firesoul
Multiple BPF-helpers that can manipulate/increase the size of the SKB uses
__bpf_skb_max_len() as the max-length. This function limit size against
the current net_device MTU (skb->dev->mtu).
When a BPF-prog grow the packet size, then it should not be limited to the
MTU. The MTU is a transmit limitation, and software receiving this packet
should be allowed to increase the size. Further more, current MTU check in
__bpf_skb_max_len uses the MTU from ingress/current net_device, which in
case of redirects uses the wrong net_device.
This patch keeps a sanity max limit of SKB_MAX_ALLOC (16KiB). The real limit
is elsewhere in the system. Jesper's testing[1] showed it was not possible
to exceed 8KiB when expanding the SKB size via BPF-helper. The limiting
factor is the define KMALLOC_MAX_CACHE_SIZE which is 8192 for
SLUB-allocator (CONFIG_SLUB) in-case PAGE_SIZE is 4096. This define is
in-effect due to this being called from softirq context see code
__gfp_pfmemalloc_flags() and __do_kmalloc_node(). Jakub's testing showed
that frames above 16KiB can cause NICs to reset (but not crash). Keep this
sanity limit at this level as memory layer can differ based on kernel
config.
[1] https://github.com/xdp-project/bpf-examples/tree/master/MTU-tests
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: John Fastabend <john.fastabend@gmail.com>
Link: https://lore.kernel.org/bpf/161287788936.790810.2937823995775097177.stgit@firesoul
This patch adds support for STBC encoding to the radiotap tx parse
function. Prior to this change adding the STBC flag to the radiotap
header did not encode frames with STBC.
Signed-off-by: Philipp Borgers <borgers@mi.fu-berlin.de>
Link: https://lore.kernel.org/r/20210125150744.83065-1-borgers@mi.fu-berlin.de
[use u8_get_bits/u32_encode_bits instead of manually shifting]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This was added to mitigate the effects of too much sampling on devices that
use a static global fallback table instead of configurable multi-rate retry.
Now that the sampling algorithm is improved, this code path no longer performs
any better than the standard probing on affected devices.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Link: https://lore.kernel.org/r/20210127055735.78599-6-nbd@nbd.name
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The biggest flaw in current minstrel_ht is the fact that it needs way too
many probing packets to be able to quickly find the best rate.
Depending on the wifi hardware and operating mode, this can significantly
reduce throughput when not operating at the highest available data rate.
In order to be able to significantly reduce the amount of rate sampling,
we need a much smarter selection of probing rates.
The new approach introduced by this patch maintains a limited set of
available rates to be tested during a statistics window.
They are split into distinct categories:
- MINSTREL_SAMPLE_TYPE_INC - incremental rate upgrade:
Pick the next rate group and find the first rate that is faster than
the current max. throughput rate
- MINSTREL_SAMPLE_TYPE_JUMP - random testing of higher rates:
Pick a random rate from the next group that is faster than the current
max throughput rate. This allows faster adaptation when the link changes
significantly
- MINSTREL_SAMPLE_TYPE_SLOW - test a rate between max_prob, max_tp2 and
max_tp in order to reduce the gap between them
In order to prioritize sampling, every 6 attempts are split into 3x INC,
2x JUMP, 1x SLOW.
Available rates are checked and refilled on every stats window update.
With this approach, we finally get a very small delta in throughput when
comparing setting the optimal data rate as a fixed rate vs normal rate
control operation.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Link: https://lore.kernel.org/r/20210127055735.78599-4-nbd@nbd.name
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In order to more gracefully be able to fall back to lower rates without too
much throughput fluctuations, initialize all untested rates below tested ones
to the maximum probabilty of higher rates.
Usually this leads to untested lower rates getting initialized with a
probability value of 100%, making them better candidates for fallback without
having to rely on random probing
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Link: https://lore.kernel.org/r/20210127055735.78599-3-nbd@nbd.name
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Get rid of a lot of divisions and modulo operations
Reduces code size and improves performance
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Link: https://lore.kernel.org/r/20210127055735.78599-1-nbd@nbd.name
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Sparse started warning on this function because we can potentially
return an uninitialized value. The reason is that if the caller
passes a min_bw value that is higher then the last value in bws[], we
will not go into the loop and reg_rule will remain initialized. This
cannot happen because the only caller of this function uses either 1
or 20 in min_bw, but the function will be more robust if we
pre-initialize the value.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210204154439.6c884ea7281c.I257278d03b0c1ae0aa6631672cfa48f1a95d5996@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The multiplication of the u32 variables tx_time and estimated_retx is
performed using a 32 bit multiplication and the result is stored in
a u64 result. This has a potential u32 overflow issue, so avoid this
by casting tx_time to a u64 to force a 64 bit multiply.
Addresses-Coverity: ("Unintentional integer overflow")
Fixes: 050ac52cbe ("mac80211: code for on-demand Hybrid Wireless Mesh Protocol")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Link: https://lore.kernel.org/r/20210205175352.208841-1-colin.king@canonical.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This patch unifies sending control port frames
over nl80211 and AF_PACKET sockets a little more.
Before this patch, EAPOL frames got QoS prioritization
only when using AF_PACKET sockets.
__ieee80211_select_queue only selects a QoS-enabled queue
for control port frames, when the control port protocol
is set correctly on the skb. For the AF_PACKET path this
works, but the nl80211 path used ETH_P_802_3.
Another check for injected frames in wme.c then prevented
the QoS TID to be copied in the frame.
In order to fix this, get rid of the frame injection marking
for nl80211 ctrl port and set the correct ethernet protocol.
Please note:
An erlier version of this path tried to prevent
frame aggregation for control port frames in order to speed up
the initial connection setup a little. This seemed to cause
issues on my older Intel dvm-based hardware, and was therefore
removed again. Future commits which try to reintroduce this
have to check carefully how hw behaves with aggregated and
non-aggregated traffic for the same TID.
My NIC: Intel(R) Centrino(R) Ultimate-N 6300 AGN, REV=0x74
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Markus Theil <markus.theil@tu-ilmenau.de>
Link: https://lore.kernel.org/r/20210206115112.567881-1-markus.theil@tu-ilmenau.de
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The ieee80211 class registers a callback which actually does nothing.
Given that the callback is optional, and all its accesses are protected
by a NULL check, remove it entirely.
Signed-off-by: Matteo Croce <mcroce@microsoft.com>
Link: https://lore.kernel.org/r/20210208113356.4105-1-mcroce@linux.microsoft.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Compile-in the socket RX queue mapping field and logic when TLS_DEVICE
is enabled. This allows device drivers to pick the recorded socket's
RX queue and use it for streams distribution.
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Reviewed-by: Maxim Mikityanskiy <maximmi@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use a new config SOCK_RX_QUEUE_MAPPING to compile-in the socket
RX queue field and logic, instead of the XPS config.
This breaks dependency in XPS, and allows selecting it from non-XPS
use cases, as we do in the next patch.
In addition, use the new flag to wrap the logic in sk_rx_queue_get()
and protect access to the sk_rx_queue_mapping field, while keeping
the function exposed unconditionally, just like sk_rx_queue_set()
and sk_rx_queue_clear().
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Reviewed-by: Maxim Mikityanskiy <maximmi@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently we do not schedule the MPTCP retransmission
timer after pushing the data when such action happens
in the subflow context.
This may cause hang-up on active-backup scenarios, or
even when only single subflow msks are involved, if we lost
some peer's ack.
Fixes: 6e628cd3a8 ("mptcp: use mptcp release_cb for delayed tasks")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move mptcp_cleanup_rbuf() related checks inside the mentioned
helper and extend them to mirror TCP checks more closely.
Additionally drop the 'rmem_pending' hack, since commit 879526030c
("mptcp: protect the rx path with the msk socket spinlock") we
can use instead 'rmem_released'.
Fixes: ea4ca586b1 ("mptcp: refine MPTCP-level ack scheduling")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mptcp subflow route_req() callback performs the subflow
req initialization after the route_req() check. If the latter
fails, mptcp-specific bits of the current request sockets
are left uninitialized.
The above causes bad things at req socket disposal time, when
the mptcp resources are cleared.
This change addresses the issue by splitting subflow_init_req()
into the actual initialization and the mptcp-specific checks.
The initialization is moved before any possibly failing check.
Reported-by: Christoph Paasch <cpaasch@apple.com>
Fixes: 7ea851d19b ("tcp: merge 'init_req' and 'route_req' functions")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Syzkaller was able to trigger the following splat again:
WARNING: CPU: 1 PID: 12512 at net/mptcp/protocol.c:761 mptcp_reset_timer+0x12a/0x160 net/mptcp/protocol.c:761
Modules linked in:
CPU: 1 PID: 12512 Comm: kworker/1:6 Not tainted 5.10.0-rc6 #52
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.13.0-0-gf21b5a4aeb02-prebuilt.qemu.org 04/01/2014
Workqueue: events mptcp_worker
RIP: 0010:mptcp_reset_timer+0x12a/0x160 net/mptcp/protocol.c:761
Code: e8 4b 0c ad ff e8 56 21 88 fe 48 b8 00 00 00 00 00 fc ff df 48 c7 04 03 00 00 00 00 48 83 c4 40 5b 5d 41 5c c3 e8 36 21 88 fe <0f> 0b 41 bc c8 00 00 00 eb 98 e8 e7 b1 af fe e9 30 ff ff ff 48 c7
RSP: 0018:ffffc900018c7c68 EFLAGS: 00010293
RAX: ffff888108cb1c80 RBX: 1ffff92000318f8d RCX: ffffffff82ad0307
RDX: 0000000000000000 RSI: ffffffff82ad036a RDI: 0000000000000007
RBP: ffff888113e2d000 R08: ffff888108cb1c80 R09: ffffed10227c5ab7
R10: ffff888113e2d5b7 R11: ffffed10227c5ab6 R12: 0000000000000000
R13: ffff88801f100000 R14: ffff888113e2d5b0 R15: 0000000000000001
FS: 0000000000000000(0000) GS:ffff88811b500000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00007fd76a874ef8 CR3: 000000001689c005 CR4: 0000000000170ee0
Call Trace:
mptcp_worker+0xaa4/0x1560 net/mptcp/protocol.c:2334
process_one_work+0x8d3/0x1200 kernel/workqueue.c:2272
worker_thread+0x9c/0x1090 kernel/workqueue.c:2418
kthread+0x303/0x410 kernel/kthread.c:292
ret_from_fork+0x22/0x30 arch/x86/entry/entry_64.S:296
The mptcp_worker tries to update the MPTCP retransmission timer
even if such timer is not currently scheduled.
The mptcp_rtx_head() return value is bogus: we can have enqueued
data not yet transmitted. The above may additionally cause spurious,
unneeded MPTCP-level retransmissions.
Fix the issue adding an explicit clearing of the rtx queue before
trying to retransmit and checking for unacked data.
Additionally drop an unneeded timer stop call and the unused
mptcp_rtx_tail() helper.
Reported-by: Christoph Paasch <cpaasch@apple.com>
Fixes: 6e628cd3a8 ("mptcp: use mptcp release_cb for delayed tasks")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current mptcp_poll() implementation gives unexpected
results after shutdown(SEND_SHUTDOWN) and when the msk
status is TCP_CLOSE.
Set the correct mask.
Fixes: 8edf08649e ("mptcp: rework poll+nospace handling")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently all errors received on msk subflows are ignored.
We need to catch at least the errors on connect() and
on fallback sockets.
Use a custom sk_error_report callback at subflow level,
and do the real action under the msk socket lock - via
the usual sock_owned_by_user()/release_callback() schema.
Fixes: 6e628cd3a8 ("mptcp: use mptcp release_cb for delayed tasks")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Explicitly define reserved field and require it and any subsequent
fields to be zero-valued for now. Additionally, limit the valid CMSG
flags that tcp_zerocopy_receive accepts.
Fixes: 7eeba1706e ("tcp: Add receive timestamp support for receive zerocopy.")
Signed-off-by: Arjun Roy <arjunroy@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Soheil Hassas Yeganeh <soheil@google.com>
Suggested-by: David Ahern <dsahern@gmail.com>
Suggested-by: Leon Romanovsky <leon@kernel.org>
Suggested-by: Jakub Kicinski <kuba@kernel.org>
Acked-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
dev_ifsioc_locked() is called with only RCU read lock, so when
there is a parallel writer changing the mac address, it could
get a partially updated mac address, as shown below:
Thread 1 Thread 2
// eth_commit_mac_addr_change()
memcpy(dev->dev_addr, addr->sa_data, ETH_ALEN);
// dev_ifsioc_locked()
memcpy(ifr->ifr_hwaddr.sa_data,
dev->dev_addr,...);
Close this race condition by guarding them with a RW semaphore,
like netdev_get_name(). We can not use seqlock here as it does not
allow blocking. The writers already take RTNL anyway, so this does
not affect the slow path. To avoid bothering existing
dev_set_mac_address() callers in drivers, introduce a new wrapper
just for user-facing callers on ioctl and rtnetlink paths.
Note, bonding also changes slave mac addresses but that requires
a separate patch due to the complexity of bonding code.
Fixes: 3710becf8a ("net: RCU locking for simple ioctl()")
Reported-by: "Gong, Sishuai" <sishuai@purdue.edu>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Cong Wang <cong.wang@bytedance.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This needs a new helper that:
- can work in a sleepable context (using sock_gen_cookie)
- takes a struct sock pointer and checks that it's not NULL
Signed-off-by: Florent Revest <revest@chromium.org>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: KP Singh <kpsingh@kernel.org>
Acked-by: Andrii Nakryiko <andrii@kernel.org>
Link: https://lore.kernel.org/bpf/20210210111406.785541-2-revest@chromium.org
el/git/bluetooth/bluetooth-next
Johan Hedberg says:
====================
pull request: bluetooth-next 2021-02-11
Here's the main bluetooth-next pull request for 5.12:
- Add support for advertising monitor offliading using Microsoft
vendor extensions
- Add firmware download support for MediaTek MT7921U USB devices
- Suspend-related fixes for Qualcomm devices
- Add support for Intel GarfieldPeak controller
- Various other smaller fixes & cleanups
Please let me know if there are any issues pulling. Thanks.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The function fib6_walk_continue() cannot return a positive value when
called from register_fib_notifier(), but ignoring causes static analyzer to
generate warnings in users of register_fib_notifier() that try to convert
returned error code to pointer with ERR_PTR(). Handle such case by
explicitly checking for positive error values and converting them to
-EINVAL in fib6_tables_dump().
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Suggested-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Vlad Buslov <vladbu@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Due to the fact that ic_dev->dev is kept open in ic_close_dev, I had
thought that ic_dev will not be freed either. But that is not the case,
but instead "everybody dies" when ipconfig cleans up, and just the
net_device behind ic_dev->dev remains allocated but not ic_dev itself.
This is a problem because in ic_close_devs, for every net device that
we're about to close, we compare it against the list of lower interfaces
of ic_dev, to figure out whether we should close it or not. But since
ic_dev itself is subject to freeing, this means that at some point in
the middle of the list of ipconfig interfaces, ic_dev will have been
freed, and we would be still attempting to iterate through its list of
lower interfaces while checking whether to bring down the remaining
ipconfig interfaces.
There are multiple ways to avoid the use-after-free: we could delay
freeing ic_dev until the very end (outside the while loop). Or an even
simpler one: we can observe that we don't need ic_dev when iterating
through its lowers, only ic_dev->dev, structure which isn't ever freed.
So, by keeping ic_dev->dev in a variable assigned prior to freeing
ic_dev, we can avoid all use-after-free issues.
Fixes: 46acf7bdbc ("Revert "net: ipv4: handle DSA enabled master network devices"")
Reported-by: kernel test robot <oliver.sang@intel.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It is simpler to make net->net_cookie a plain u64
written once in setup_net() instead of looping
and using atomic64 helpers.
Lorenz Bauer wants to add SO_NETNS_COOKIE socket option
and this patch would makes his patch series simpler.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Daniel Borkmann <daniel@iogearbox.net>
Cc: Lorenz Bauer <lmb@cloudflare.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Tested-by: Lorenz Bauer <lmb@cloudflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add offloading for HSR/PRP (IEC 62439-3) tag insertion, tag removal
forwarding and duplication supported by the xrs7000 series switches.
Only HSR v1 and PRP v1 are supported by the xrs7000 series switches (HSR
v0 is not).
Signed-off-by: George McCollister <george.mccollister@gmail.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for offloading of HSR/PRP (IEC 62439-3) tag insertion
tag removal, duplicate generation and forwarding on DSA switches.
Add DSA_NOTIFIER_HSR_JOIN and DSA_NOTIFIER_HSR_LEAVE which trigger calls
to .port_hsr_join and .port_hsr_leave in the DSA driver for the switch.
The DSA switch driver should then set netdev feature flags for the
HSR/PRP operation that it offloads.
NETIF_F_HW_HSR_TAG_INS
NETIF_F_HW_HSR_TAG_RM
NETIF_F_HW_HSR_FWD
NETIF_F_HW_HSR_DUP
Signed-off-by: George McCollister <george.mccollister@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for offloading of HSR/PRP (IEC 62439-3) tag insertion
tag removal, duplicate generation and forwarding.
For HSR, insertion involves the switch adding a 6 byte HSR header after
the 14 byte Ethernet header. For PRP it adds a 6 byte trailer.
Tag removal involves automatically stripping the HSR/PRP header/trailer
in the switch. This is possible when the switch also performs auto
deduplication using the HSR/PRP header/trailer (making it no longer
required).
Forwarding involves automatically forwarding between redundant ports in
an HSR. This is crucial because delay is accumulated as a frame passes
through each node in the ring.
Duplication involves the switch automatically sending a single frame
from the CPU port to both redundant ports. This is required because the
inserted HSR/PRP header/trailer must contain the same sequence number
on the frames sent out both redundant ports.
Export is_hsr_master so DSA can tell them apart from other devices in
dsa_slave_changeupper.
Signed-off-by: George McCollister <george.mccollister@gmail.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For a switch to offload insertion of HSR/PRP tags, frames must not be
sent to the CPU facing switch port with a tag. Generate supervision frames
(eth type ETH_P_PRP) without HSR v1 (ETH_P_HSR)/PRP tag and rely on
create_tagged_frame which inserts it later. This will allow skipping the
tag insertion for all outgoing frames in the future which is required for
HSR v1/PRP tag insertions to be offloaded.
HSR v0 supervision frames always contain tag information so insertion of
the tag can't be offloaded. IEC 62439-3 Ed.2.0 (HSR v1) specifically
notes that this was changed since v0 to allow offloading.
Signed-off-by: George McCollister <george.mccollister@gmail.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Tested-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Even when implementing RFC 6056 3.3.4 (Algorithm 4: Double-Hash
Port Selection Algorithm), a patient attacker could still be able
to collect enough state from an otherwise idle host.
Idea of this patch is to inject some noise, in the
cases __inet_hash_connect() found a candidate in the first
attempt.
This noise should not significantly reduce the collision
avoidance, and should be zero if connection table
is already well used.
Note that this is not implementing RFC 6056 3.3.5
because we think Algorithm 5 could hurt typical
workloads.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: David Dworken <ddworken@google.com>
Cc: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
RFC 6056 (Recommendations for Transport-Protocol Port Randomization)
provides good summary of why source selection needs extra care.
David Dworken reminded us that linux implements Algorithm 3
as described in RFC 6056 3.3.3
Quoting David :
In the context of the web, this creates an interesting info leak where
websites can count how many TCP connections a user's computer is
establishing over time. For example, this allows a website to count
exactly how many subresources a third party website loaded.
This also allows:
- Distinguishing between different users behind a VPN based on
distinct source port ranges.
- Tracking users over time across multiple networks.
- Covert communication channels between different browsers/browser
profiles running on the same computer
- Tracking what applications are running on a computer based on
the pattern of how fast source ports are getting incremented.
Section 3.3.4 describes an enhancement, that reduces
attackers ability to use the basic information currently
stored into the shared 'u32 hint'.
This change also decreases collision rate when
multiple applications need to connect() to
different destinations.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: David Dworken <ddworken@google.com>
Cc: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The changes to make rxrpc create the udp socket missed a bit to add the
Kconfig dependency on the udp tunnel code to do this.
Fix this by adding making AF_RXRPC select NET_UDP_TUNNEL.
Fixes: 1a9b86c9fd ("rxrpc: use udp tunnel APIs instead of open code in rxrpc_open_socket")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Vadim Fedorenko <vfedorenko@novek.ru>
Signed-off-by: David Howells <dhowells@redhat.com>
Reviewed-by: Xin Long <lucien.xin@gmail.com>
cc: alaa@dev.mellanox.co.il
cc: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Reject the unsupported and invalid ct_state flags of cls flower rules.
Fixes: e0ace68af2 ("net/sched: cls_flower: Add matching on conntrack info")
Signed-off-by: wenxu <wenxu@ucloud.cn>
Reviewed-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes from David Miller:
"Another pile of networing fixes:
1) ath9k build error fix from Arnd Bergmann
2) dma memory leak fix in mediatec driver from Lorenzo Bianconi.
3) bpf int3 kprobe fix from Alexei Starovoitov.
4) bpf stackmap integer overflow fix from Bui Quang Minh.
5) Add usb device ids for Cinterion MV31 to qmi_qwwan driver, from
Christoph Schemmel.
6) Don't update deleted entry in xt_recent netfilter module, from
Jazsef Kadlecsik.
7) Use after free in nftables, fix from Pablo Neira Ayuso.
8) Header checksum fix in flowtable from Sven Auhagen.
9) Validate user controlled length in qrtr code, from Sabyrzhan
Tasbolatov.
10) Fix race in xen/netback, from Juergen Gross,
11) New device ID in cxgb4, from Raju Rangoju.
12) Fix ring locking in rxrpc release call, from David Howells.
13) Don't return LAPB error codes from x25_open(), from Xie He.
14) Missing error returns in gsi_channel_setup() from Alex Elder.
15) Get skb_copy_and_csum_datagram working properly with odd segment
sizes, from Willem de Bruijn.
16) Missing RFS/RSS table init in enetc driver, from Vladimir Oltean.
17) Do teardown on probe failure in DSA, from Vladimir Oltean.
18) Fix compilation failures of txtimestamp selftest, from Vadim
Fedorenko.
19) Limit rx per-napi gro queue size to fix latency regression, from
Eric Dumazet.
20) dpaa_eth xdp fixes from Camelia Groza.
21) Missing txq mode update when switching CBS off, in stmmac driver,
from Mohammad Athari Bin Ismail.
22) Failover pending logic fix in ibmvnic driver, from Sukadev
Bhattiprolu.
23) Null deref fix in vmw_vsock, from Norbert Slusarek.
24) Missing verdict update in xdp paths of ena driver, from Shay
Agroskin.
25) seq_file iteration fix in sctp from Neil Brown.
26) bpf 32-bit src register truncation fix on div/mod, from Daniel
Borkmann.
27) Fix jmp32 pruning in bpf verifier, from Daniel Borkmann.
28) Fix locking in vsock_shutdown(), from Stefano Garzarella.
29) Various missing index bound checks in hns3 driver, from Yufeng Mo.
30) Flush ports on .phylink_mac_link_down() in dsa felix driver, from
Vladimir Oltean.
31) Don't mix up stp and mrp port states in bridge layer, from Horatiu
Vultur.
32) Fix locking during netif_tx_disable(), from Edwin Peer"
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (45 commits)
bpf: Fix 32 bit src register truncation on div/mod
bpf: Fix verifier jmp32 pruning decision logic
bpf: Fix verifier jsgt branch analysis on max bound
vsock: fix locking in vsock_shutdown()
net: hns3: add a check for index in hclge_get_rss_key()
net: hns3: add a check for tqp_index in hclge_get_ring_chain_from_mbx()
net: hns3: add a check for queue_id in hclge_reset_vf_queue()
net: dsa: felix: implement port flushing on .phylink_mac_link_down
switchdev: mrp: Remove SWITCHDEV_ATTR_ID_MRP_PORT_STAT
bridge: mrp: Fix the usage of br_mrp_port_switchdev_set_state
net: watchdog: hold device global xmit lock during tx disable
netfilter: nftables: relax check for stateful expressions in set definition
netfilter: conntrack: skip identical origin tuple in same zone only
vsock/virtio: update credit only if socket is not closed
net: fix iteration for sctp transport seq_files
net: ena: Update XDP verdict upon failure
net/vmw_vsock: improve locking in vsock_connect_timeout()
net/vmw_vsock: fix NULL pointer dereference
ibmvnic: Clear failover_pending if unable to schedule
net: stmmac: set TxQ mode back to DCB after disabling CBS
...
Pablo Neira Ayuso says:
====================
Netfilter fixes for net
The following patchset contains Netfilter fixes for net:
1) nf_conntrack_tuple_taken() needs to recheck zone for
NAT clash resolution, from Florian Westphal.
2) Restore support for stateful expressions when set definition
specifies no stateful expressions.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
In vsock_shutdown() we touched some socket fields without holding the
socket lock, such as 'state' and 'sk_flags'.
Also, after the introduction of multi-transport, we are accessing
'vsk->transport' in vsock_send_shutdown() without holding the lock
and this call can be made while the connection is in progress, so
the transport can change in the meantime.
To avoid issues, we hold the socket lock when we enter in
vsock_shutdown() and release it when we leave.
Among the transports that implement the 'shutdown' callback, only
hyperv_transport acquired the lock. Since the caller now holds it,
we no longer take it.
Fixes: d021c34405 ("VSOCK: Introduce VM Sockets")
Signed-off-by: Stefano Garzarella <sgarzare@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds a new sysfs attribute to the network device class.
Said attribute provides a per-device control to enable/disable the
threaded mode for all the napi instances of the given network device,
without the need for a device up/down.
User sets it to 1 or 0 to enable or disable threaded mode.
Note: when switching between threaded and the current softirq based mode
for a napi instance, it will not immediately take effect if the napi is
currently being polled. The mode switch will happen for the next time
napi_schedule() is called.
Co-developed-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Co-developed-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Co-developed-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Wei Wang <weiwan@google.com>
Reviewed-by: Alexander Duyck <alexanderduyck@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch allows running each napi poll loop inside its own
kernel thread.
The kthread is created during netif_napi_add() if dev->threaded
is set. And threaded mode is enabled in napi_enable(). We will
provide a way to set dev->threaded and enable threaded mode
without a device up/down in the following patch.
Once that threaded mode is enabled and the kthread is
started, napi_schedule() will wake-up such thread instead
of scheduling the softirq.
The threaded poll loop behaves quite likely the net_rx_action,
but it does not have to manipulate local irqs and uses
an explicit scheduling point based on netdev_budget.
Co-developed-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Co-developed-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Co-developed-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Wei Wang <weiwan@google.com>
Reviewed-by: Alexander Duyck <alexanderduyck@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This commit introduces a new function __napi_poll() which does the main
logic of the existing napi_poll() function, and will be called by other
functions in later commits.
This idea and implementation is done by Felix Fietkau <nbd@nbd.name> and
is proposed as part of the patch to move napi work to work_queue
context.
This commit by itself is a code restructure.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Wei Wang <weiwan@google.com>
Reviewed-by: Alexander Duyck <alexanderduyck@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Steffen Klassert says:
====================
pull request (net-next): ipsec-next 2021-02-09
1) Support TSO on xfrm interfaces.
From Eyal Birger.
2) Variable calculation simplifications in esp4/esp6.
From Jiapeng Chong / Jiapeng Zhong.
3) Fix a return code in xfrm_do_migrate.
From Zheng Yongjun.
Please pull or let me know if there are problems.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the value '2' to 'fib_notify_on_flag_change' to allow sending
notifications only for failed route installation.
Separate value is added for such notifications because there are less of
them, so they do not impact performance and some users will find them more
important.
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After installing a route to the kernel, user space receives an
acknowledgment, which means the route was installed in the kernel, but not
necessarily in hardware.
The asynchronous nature of route installation in hardware can lead to a
routing daemon advertising a route before it was actually installed in
hardware. This can result in packet loss or mis-routed packets until the
route is installed in hardware.
To avoid such cases, previous patch set added the ability to emit
RTM_NEWROUTE notifications whenever RTM_F_OFFLOAD/RTM_F_TRAP flags
are changed, this behavior is controlled by sysctl.
With the above mentioned behavior, it is possible to know from user-space
if the route was offloaded, but if the offload fails there is no indication
to user-space. Following a failure, a routing daemon will wait indefinitely
for a notification that will never come.
This patch adds an "offload_failed" indication to IPv6 routes, so that
users will have better visibility into the offload process.
'struct fib6_info' is extended with new field that indicates if route
offload failed. Note that the new field is added using unused bit and
therefore there is no need to increase struct size.
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the value '2' to 'fib_notify_on_flag_change' to allow sending
notifications only for failed route installation.
Separate value is added for such notifications because there are less of
them, so they do not impact performance and some users will find them more
important.
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After installing a route to the kernel, user space receives an
acknowledgment, which means the route was installed in the kernel, but not
necessarily in hardware.
The asynchronous nature of route installation in hardware can lead to a
routing daemon advertising a route before it was actually installed in
hardware. This can result in packet loss or mis-routed packets until the
route is installed in hardware.
To avoid such cases, previous patch set added the ability to emit
RTM_NEWROUTE notifications whenever RTM_F_OFFLOAD/RTM_F_TRAP flags
are changed, this behavior is controlled by sysctl.
With the above mentioned behavior, it is possible to know from user-space
if the route was offloaded, but if the offload fails there is no indication
to user-space. Following a failure, a routing daemon will wait indefinitely
for a notification that will never come.
This patch adds an "offload_failed" indication to IPv4 routes, so that
users will have better visibility into the offload process.
'struct fib_alias', and 'struct fib_rt_info' are extended with new field
that indicates if route offload failed. Note that the new field is added
using unused bit and therefore there is no need to increase structs size.
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The function br_mrp_port_switchdev_set_state was called both with MRP
port state and STP port state, which is an issue because they don't
match exactly.
Therefore, update the function to be used only with STP port state and
use the id SWITCHDEV_ATTR_ID_PORT_STP_STATE.
The choice of using STP over MRP is that the drivers already implement
SWITCHDEV_ATTR_ID_PORT_STP_STATE and already in SW we update the port
STP state.
Fixes: 9a9f26e8f7 ("bridge: mrp: Connect MRP API with the switchdev API")
Fixes: fadd409136 ("bridge: switchdev: mrp: Implement MRP API for switchdev")
Fixes: 2f1a11ae11 ("bridge: mrp: Add MRP interface.")
Reported-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Restore the original behaviour where users are allowed to add an element
with any stateful expression if the set definition specifies no stateful
expressions. Make sure upper maximum number of stateful expressions of
NFT_SET_EXPR_MAX is not reached.
Fixes: 8cfd9b0f85 ("netfilter: nftables: generalize set expressions support")
Fixes: 48b0ae046e ("netfilter: nftables: netlink support for several set element expressions")
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
In rxrpc_open_socket(), now it's using sock_create_kern() and
kernel_bind() to create a udp tunnel socket, and other kernel
APIs to set up it. These code can be replaced with udp tunnel
APIs udp_sock_create() and setup_udp_tunnel_sock(), and it'll
simplify rxrpc_open_socket().
Note that with this patch, the udp tunnel socket will always
bind to a random port if transport is not provided by users,
which is suggested by David Howells, thanks!
Acked-by: David Howells <dhowells@redhat.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Reviewed-by: Vadim Fedorenko <vfedorenko@novek.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to access the suboordinate dev for a device we should be holding
the rtnl_lock when outside of the transmit path. The existing code was not
doing that for the sysfs dump function and as a result we were open to a
possible race.
To resolve that take the rtnl lock prior to accessing the sb_dev field of
the Tx queue and release it after we have retrieved the tc for the queue.
Signed-off-by: Alexander Duyck <alexanderduyck@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The origin skip check needs to re-test the zone. Else, we might skip
a colliding tuple in the reply direction.
This only occurs when using 'directional zones' where origin tuples
reside in different zones but the reply tuples share the same zone.
This causes the new conntrack entry to be dropped at confirmation time
because NAT clash resolution was elided.
Fixes: 4e35c1cb94 ("netfilter: nf_nat: skip nat clash resolution for same-origin entries")
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
If the socket is closed or is being released, some resources used by
virtio_transport_space_update() such as 'vsk->trans' may be released.
To avoid a use after free bug we should only update the available credit
when we are sure the socket is still open and we have the lock held.
Fixes: 06a8fc7836 ("VSOCK: Introduce virtio_vsock_common.ko")
Signed-off-by: Stefano Garzarella <sgarzare@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Link: https://lore.kernel.org/r/20210208144454.84438-1-sgarzare@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The set of required attributes for a given SRv6 behavior is identified
using a bitmap stored in an unsigned long, since the initial design of SRv6
networking in Linux. Recently the same approach has been used for
identifying the optional attributes.
However, the number of attributes supported by SRv6 behaviors depends on
the size of the unsigned long type which changes with the architecture.
Indeed, on a 64-bit architecture, an SRv6 behavior can support up to 64
attributes while on a 32-bit architecture it can support at most 32
attributes.
To fool-proof the processing of SRv6 behaviors we verify, at compile time,
that the set of all supported SRv6 attributes can be encoded into a bitmap
stored in an unsigned long. Otherwise, kernel build fails forcing
developers to reconsider adding a new attribute or extend the total
number of supported attributes by the SRv6 behaviors.
Moreover, we replace all patterns (1 << i) with the macro SEG6_F_ATTR(i) in
order to address potential overflow issues caused by 32-bit signed
arithmetic.
Thanks to Colin Ian King for catching the overflow problem, providing a
solution and inspiring this patch.
Thanks to Jakub Kicinski for his useful suggestions during the design of
this patch.
v2:
- remove the SEG6_LOCAL_MAX_SUPP which is not strictly needed: it can
be derived from the unsigned long type. Thanks to David Ahern for
pointing it out.
Signed-off-by: Andrea Mayer <andrea.mayer@uniroma2.it>
Reviewed-by: David Ahern <dsahern@kernel.org>
Link: https://lore.kernel.org/r/20210206170934.5982-1-andrea.mayer@uniroma2.it
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
of Feb 2nd (batadv-next-pullrequest-20210202) and includes the
following patches:
- Bump version strings, by Simon Wunderlich (added commit log)
- Drop publication years from copyright info, by Sven Eckelmann
(replaced the previous patch which updated copyright years, as per
our discussion)
- Avoid sizeof on flexible structure, by Sven Eckelmann (unchanged)
- Fix names for kernel-doc blocks, by Sven Eckelmann (unchanged)
-----BEGIN PGP SIGNATURE-----
iQJKBAABCgA0FiEE1ilQI7G+y+fdhnrfoSvjmEKSnqEFAmAhbUkWHHN3QHNpbW9u
d3VuZGVybGljaC5kZQAKCRChK+OYQpKeoR7yEACMhdCzMoVPJQwOYWe5p6QwgaBz
85QRT56x9gpFhV5dXCyg7DK3Qt2JRfTfBtMOeZQatFxcACYaGunZSS1L6gDVATpT
5vB+5UwQK8AW7cjkwVS6vJWW9Wmll9IwNe0/1DGvSBjEWwmU/wlRzAPa2uAT2uw5
AxrErEuXo5M3U4mDfJckVD4XA+pKkd9ylLEQ7llcZA4rOaTsr5sNAy5mbxO5EXD9
yP1vq9BoXtsf0FyZbQrMnYre6teAkxVxrvkTn6v44vsFKsi69JaxDiKQ4T7vakZR
1rIQq/8XbkH0dQXEu4C2FtWTzrg9P4KNHBPiT06b+KxlROpfYivcWhIqlofmW2FJ
5bWlumyNg3WoUmaM9kLGTFHagAp8M968W8zsI5fLi0meX0pEzFe/E1iBfkQaYyHh
R8Xpt7z1ORYUavFhVXqMw8x92WOLWmdFZjSGaW6sNyCxMFIU7qR16gYcXmucrJyU
RY6o159D9AKVOdX/GdX50mvyHjn/lC3KUEGQLUVxXMdJHpj7avn7aEiCWHUvgAxQ
jIHLOy0CRsUlCFPmzSqwGs3dAJEZeFbvqMwZjFJ/UXlKwBgPVMy76wIUk57+FWKz
3DTcg+6RIiW+bWazn/Hdbn9JXUNZnp5C6oH62GFPw7G6ywfe/yPex4qubF7feyog
T9H6ho+KW3SmRsHY5Q==
=fX7f
-----END PGP SIGNATURE-----
Merge tag 'batadv-next-pullrequest-20210208' of git://git.open-mesh.org/linux-merge
Simon Wunderlich says:
====================
This feature/cleanup patchset is an updated version of the pull request
of Feb 2nd (batadv-next-pullrequest-20210202) and includes the
following patches:
- Bump version strings, by Simon Wunderlich (added commit log)
- Drop publication years from copyright info, by Sven Eckelmann
(replaced the previous patch which updated copyright years, as per
our discussion)
- Avoid sizeof on flexible structure, by Sven Eckelmann (unchanged)
- Fix names for kernel-doc blocks, by Sven Eckelmann (unchanged)
* tag 'batadv-next-pullrequest-20210208' of git://git.open-mesh.org/linux-merge:
batman-adv: Fix names for kernel-doc blocks
batman-adv: Avoid sizeof on flexible structure
batman-adv: Drop publication years from copyright info
batman-adv: Start new development cycle
====================
Link: https://lore.kernel.org/r/20210208165938.13262-1-sw@simonwunderlich.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The sctp transport seq_file iterators take a reference to the transport
in the ->start and ->next functions and releases the reference in the
->show function. The preferred handling for such resources is to
release them in the subsequent ->next or ->stop function call.
Since Commit 1f4aace60b ("fs/seq_file.c: simplify seq_file iteration
code and interface") there is no guarantee that ->show will be called
after ->next, so this function can now leak references.
So move the sctp_transport_put() call to ->next and ->stop.
Fixes: 1f4aace60b ("fs/seq_file.c: simplify seq_file iteration code and interface")
Reported-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: NeilBrown <neilb@suse.de>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Pablo Neira Ayuso says:
====================
Netfilter/IPVS updates for net-next
1) Remove indirection and use nf_ct_get() instead from nfnetlink_log
and nfnetlink_queue, from Florian Westphal.
2) Add weighted random twos choice least-connection scheduling for IPVS,
from Darby Payne.
3) Add a __hash placeholder in the flow tuple structure to identify
the field to be included in the rhashtable key hash calculation.
4) Add a new nft_parse_register_load() and nft_parse_register_store()
to consolidate register load and store in the core.
5) Statify nft_parse_register() since it has no more module clients.
6) Remove redundant assignment in nft_cmp, from Colin Ian King.
* git://git.kernel.org/pub/scm/linux/kernel/git/pablo/nf-next:
netfilter: nftables: remove redundant assignment of variable err
netfilter: nftables: statify nft_parse_register()
netfilter: nftables: add nft_parse_register_store() and use it
netfilter: nftables: add nft_parse_register_load() and use it
netfilter: flowtable: add hash offset field to tuple
ipvs: add weighted random twos choice algorithm
netfilter: ctnetlink: remove get_ct indirection
====================
Link: https://lore.kernel.org/r/20210206015005.23037-1-pablo@netfilter.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
A possible locking issue in vsock_connect_timeout() was recognized by
Eric Dumazet which might cause a null pointer dereference in
vsock_transport_cancel_pkt(). This patch assures that
vsock_transport_cancel_pkt() will be called within the lock, so a race
condition won't occur which could result in vsk->transport to be set to NULL.
Fixes: 380feae0de ("vsock: cancel packets when failing to connect")
Reported-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Norbert Slusarek <nslusarek@gmx.net>
Reviewed-by: Stefano Garzarella <sgarzare@redhat.com>
Link: https://lore.kernel.org/r/trinity-f8e0937a-cf0e-4d80-a76e-d9a958ba3ef1-1612535522360@3c-app-gmx-bap12
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In vsock_stream_connect(), a thread will enter schedule_timeout().
While being scheduled out, another thread can enter vsock_stream_connect()
as well and set vsk->transport to NULL. In case a signal was sent, the
first thread can leave schedule_timeout() and vsock_transport_cancel_pkt()
will be called right after. Inside vsock_transport_cancel_pkt(), a null
dereference will happen on transport->cancel_pkt.
Fixes: c0cfa2d8a7 ("vsock: add multi-transports support")
Signed-off-by: Norbert Slusarek <nslusarek@gmx.net>
Reviewed-by: Stefano Garzarella <sgarzare@redhat.com>
Link: https://lore.kernel.org/r/trinity-c2d6cede-bfb1-44e2-85af-1fbc7f541715-1612535117028@3c-app-gmx-bap12
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The "dev_has_header" function, recently added in
commit d549699048 ("net/packet: fix packet receive on L3 devices
without visible hard header"),
is more accurate as criteria for determining whether a device exposes
the LL header to upper layers, because in addition to dev->header_ops,
it also checks for dev->header_ops->create.
When transmitting an skb on a device, dev_hard_header can be called to
generate an LL header. dev_hard_header will only generate a header if
dev->header_ops->create is present.
Signed-off-by: Xie He <xie.he.0141@gmail.com>
Acked-by: Willem de Bruijn <willemb@google.com>
Link: https://lore.kernel.org/r/20210205224124.21345-1-xie.he.0141@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Vladimir Oltean
Alexander Lobakin
Eric Dumazet
Davide Caratti
David S. Miller
Vadim Fedorenko
Doug Brown
Florian Westphal
Jesper Dangaard Brouer
Ben Greear
Philipp Borgers
Felix Fietkau
Luca Coelho
Colin Ian King
Markus Theil
Matteo Croce
Tariq Toukan
Paolo Abeni
Arjun Roy
Cong Wang
Florent Revest
Vlad Buslov
George McCollister
David Howells
wenxu
Linus Torvalds
Stefano Garzarella
Wei Wang
Amit Cohen
Horatiu Vultur
Pablo Neira Ayuso
Xin Long
Alexander Duyck
Andrea Mayer
Jakub Kicinski
NeilBrown
Norbert Slusarek
Xie He