By using the maple tree and the maple tree state, the vmacache is no
longer beneficial and is complicating the VMA code. Remove the vmacache
to reduce the work in keeping it up to date and code complexity.
Link: https://lkml.kernel.org/r/20220906194824.2110408-26-Liam.Howlett@oracle.com
Signed-off-by: Liam R. Howlett <Liam.Howlett@Oracle.com>
Acked-by: Vlastimil Babka <vbabka@suse.cz>
Tested-by: Yu Zhao <yuzhao@google.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: David Hildenbrand <david@redhat.com>
Cc: David Howells <dhowells@redhat.com>
Cc: Davidlohr Bueso <dave@stgolabs.net>
Cc: "Matthew Wilcox (Oracle)" <willy@infradead.org>
Cc: SeongJae Park <sj@kernel.org>
Cc: Sven Schnelle <svens@linux.ibm.com>
Cc: Will Deacon <will@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
KGDB and KDB allow read and write access to kernel memory, and thus
should be restricted during lockdown. An attacker with access to a
serial port (for example, via a hypervisor console, which some cloud
vendors provide over the network) could trigger the debugger so it is
important that the debugger respect the lockdown mode when/if it is
triggered.
Fix this by integrating lockdown into kdb's existing permissions
mechanism. Unfortunately kgdb does not have any permissions mechanism
(although it certainly could be added later) so, for now, kgdb is simply
and brutally disabled by immediately exiting the gdb stub without taking
any action.
For lockdowns established early in the boot (e.g. the normal case) then
this should be fine but on systems where kgdb has set breakpoints before
the lockdown is enacted than "bad things" will happen.
CVE: CVE-2022-21499
Co-developed-by: Stephen Brennan <stephen.s.brennan@oracle.com>
Signed-off-by: Stephen Brennan <stephen.s.brennan@oracle.com>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In preparation to enable -Wimplicit-fallthrough for Clang, fix a
fall-through warning by explicitly adding a goto statement instead
of letting the code fall through to the next case.
Link: https://github.com/KSPP/linux/issues/115
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Link: https://lore.kernel.org/r/20210528200222.GA39201@embeddedor
Signed-off-by: Daniel Thompson <daniel.thompson@linaro.org>
Currently breakpoints in kernel .init.text section are not handled
correctly while allowing to remove them even after corresponding pages
have been freed.
Fix it via killing .init.text section breakpoints just prior to initmem
pages being freed.
Doug: "HW breakpoints aren't handled by this patch but it's probably
not such a big deal".
Link: https://lkml.kernel.org/r/20210224081652.587785-1-sumit.garg@linaro.org
Signed-off-by: Sumit Garg <sumit.garg@linaro.org>
Suggested-by: Doug Anderson <dianders@chromium.org>
Acked-by: Doug Anderson <dianders@chromium.org>
Acked-by: Daniel Thompson <daniel.thompson@linaro.org>
Tested-by: Daniel Thompson <daniel.thompson@linaro.org>
Cc: Masami Hiramatsu <mhiramat@kernel.org>
Cc: Steven Rostedt (VMware) <rostedt@goodmis.org>
Cc: Jason Wessel <jason.wessel@windriver.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
To the very best of my knowledge there has never been any in-tree
code that calls this function. It exists largely to support an
out-of-tree driver that provides kgdb-over-ethernet using the
netpoll API.
kgdboe has been out-of-tree for more than 10 years and I don't
recall any serious attempt to upstream it at any point in the last
five. At this stage it looks better to stop carrying this code in
the kernel and integrate the code into the out-of-tree driver
instead.
The long term trajectory for the kernel looks likely to include
effort to remove or reduce the use of tasklets (something that has
also been true for the last 10 years). Thus the main real reason
for this patch is to make explicit that the in-tree kgdb features
do not require tasklets.
Signed-off-by: Daniel Thompson <daniel.thompson@linaro.org>
Link: https://lore.kernel.org/r/20210210142525.2876648-1-daniel.thompson@linaro.org
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Acked-by: Davidlohr Bueso <dbueso@suse.de>
Acked-by: Jason Wessel <jason.wessel@windriver.com>
The command 'find ./kernel/debug/ | xargs ./scripts/kernel-doc -none'
reported a typo in the kernel-doc of kgdb_unregister_io_module().
Rectify the kernel-doc, such that no issues remain for ./kernel/debug/.
Signed-off-by: Lukas Bulwahn <lukas.bulwahn@gmail.com>
Link: https://lore.kernel.org/r/20210125144847.21896-1-lukas.bulwahn@gmail.com
Signed-off-by: Daniel Thompson <daniel.thompson@linaro.org>
Get rid of the __call_single_node union and cleanup the API a little
to avoid external code relying on the structure layout as much.
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Frederic Weisbecker <frederic@kernel.org>
During debug trap execution we expect dbg_deactivate_sw_breakpoints()
to be paired with an dbg_activate_sw_breakpoint(). Currently although
the calls are paired correctly they are needlessly smeared across three
different functions. Worse this also results in code to drive polled I/O
being called with breakpoints activated which, in turn, needlessly
increases the set of functions that will recursively trap if breakpointed.
Fix this by moving the activation of breakpoints into the debug core.
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20200927211531.1380577-4-daniel.thompson@linaro.org
Signed-off-by: Daniel Thompson <daniel.thompson@linaro.org>
Currently kgdb honours the kprobe blocklist but doesn't place its own
trap handling code on the list. Add labels to discourage attempting to
use kgdb to debug itself.
Not every functions that executes from the trap handler needs to be
marked up: relatively early in the trap handler execution (just after
we bring the other CPUs to a halt) all breakpoints are replaced with
the original opcodes. This patch marks up code in the debug_core that
executes between trap entry and the breakpoints being deactivated
and, also, code that executes between breakpoint activation and trap
exit.
To be clear these changes are not sufficient to make recursive trapping
impossible since they do not include library calls made during kgdb's
entry/exit logic. However going much further whilst we are sharing the
kprobe blocklist risks reducing the capabilities of kprobe and this
would be a bad trade off (especially so given kgdb's users are currently
conditioned to avoid recursive traps).
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20200927211531.1380577-3-daniel.thompson@linaro.org
Signed-off-by: Daniel Thompson <daniel.thompson@linaro.org>
Currently kgdb has absolutely no safety rails in place to discourage or
prevent a user from placing a breakpoint in dangerous places such as
the debugger's own trap entry/exit and other places where it is not safe
to take synchronous traps.
Introduce a new config symbol KGDB_HONOUR_BLOCKLIST and modify the
default implementation of kgdb_validate_break_address() so that we use
the kprobe blocklist to prohibit instrumentation of critical functions
if the config symbol is set. The config symbol dependencies are set to
ensure that the blocklist will be enabled by default if we enable KGDB
and are compiling for an architecture where we HAVE_KPROBES.
Suggested-by: Peter Zijlstra <peterz@infradead.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Masami Hiramatsu <mhiramat@kernel.org>
Link: https://lore.kernel.org/r/20200927211531.1380577-2-daniel.thompson@linaro.org
Signed-off-by: Daniel Thompson <daniel.thompson@linaro.org>
On my system the kernel processes the "kgdb_earlycon" parameter before
the "kgdbcon" parameter. When we setup "kgdb_earlycon" we'll end up
in kgdb_register_callbacks() and "kgdb_use_con" won't have been set
yet so we'll never get around to starting "kgdbcon". Let's remedy
this by detecting that the IO module was already registered when
setting "kgdb_use_con" and registering the console then.
As part of this, to avoid pre-declaring things, move the handling of
the "kgdbcon" further down in the file.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20200630151422.1.I4aa062751ff5e281f5116655c976dff545c09a46@changeid
Signed-off-by: Daniel Thompson <daniel.thompson@linaro.org>
This converts all the existing DECLARE_TASKLET() (and ...DISABLED)
macros with DECLARE_TASKLET_OLD() in preparation for refactoring the
tasklet callback type. All existing DECLARE_TASKLET() users had a "0"
data argument, it has been removed here as well.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Kees Cook <keescook@chromium.org>
At times when I'm using kgdb I see a splat on my console about
suspicious RCU usage. I managed to come up with a case that could
reproduce this that looked like this:
WARNING: suspicious RCU usage
5.7.0-rc4+ #609 Not tainted
-----------------------------
kernel/pid.c:395 find_task_by_pid_ns() needs rcu_read_lock() protection!
other info that might help us debug this:
rcu_scheduler_active = 2, debug_locks = 1
3 locks held by swapper/0/1:
#0: ffffff81b6b8e988 (&dev->mutex){....}-{3:3}, at: __device_attach+0x40/0x13c
#1: ffffffd01109e9e8 (dbg_master_lock){....}-{2:2}, at: kgdb_cpu_enter+0x20c/0x7ac
#2: ffffffd01109ea90 (dbg_slave_lock){....}-{2:2}, at: kgdb_cpu_enter+0x3ec/0x7ac
stack backtrace:
CPU: 7 PID: 1 Comm: swapper/0 Not tainted 5.7.0-rc4+ #609
Hardware name: Google Cheza (rev3+) (DT)
Call trace:
dump_backtrace+0x0/0x1b8
show_stack+0x1c/0x24
dump_stack+0xd4/0x134
lockdep_rcu_suspicious+0xf0/0x100
find_task_by_pid_ns+0x5c/0x80
getthread+0x8c/0xb0
gdb_serial_stub+0x9d4/0xd04
kgdb_cpu_enter+0x284/0x7ac
kgdb_handle_exception+0x174/0x20c
kgdb_brk_fn+0x24/0x30
call_break_hook+0x6c/0x7c
brk_handler+0x20/0x5c
do_debug_exception+0x1c8/0x22c
el1_sync_handler+0x3c/0xe4
el1_sync+0x7c/0x100
rpmh_rsc_probe+0x38/0x420
platform_drv_probe+0x94/0xb4
really_probe+0x134/0x300
driver_probe_device+0x68/0x100
__device_attach_driver+0x90/0xa8
bus_for_each_drv+0x84/0xcc
__device_attach+0xb4/0x13c
device_initial_probe+0x18/0x20
bus_probe_device+0x38/0x98
device_add+0x38c/0x420
If I understand properly we should just be able to blanket kgdb under
one big RCU read lock and the problem should go away. We'll add it to
the beast-of-a-function known as kgdb_cpu_enter().
With this I no longer get any splats and things seem to work fine.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20200602154729.v2.1.I70e0d4fd46d5ed2aaf0c98a355e8e1b7a5bb7e4e@changeid
Signed-off-by: Daniel Thompson <daniel.thompson@linaro.org>
Here is the tty and serial driver updates for 5.8-rc1
Nothing huge at all, just a lot of little serial driver fixes, updates
for new devices and features, and other small things. Full details are
in the shortlog.
Note, you will get a conflict merging with your tree in the
Documentation/devicetree/bindings/serial/rs485.yaml file, but it should
be pretty obvious what to do. If not, I'm sure Rob will clean it all up
afterwards :)
All of these have been in linux-next with no issues for a while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXtzpCg8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ylRxACgjGtOKPjahONL4lWd0F8ZYEcyw7sAn34woBCO
BDUV3kolrRQ4OYNJWsHP
=TvqG
-----END PGP SIGNATURE-----
Merge tag 'tty-5.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial driver updates from Greg KH:
"Here is the tty and serial driver updates for 5.8-rc1
Nothing huge at all, just a lot of little serial driver fixes, updates
for new devices and features, and other small things. Full details are
in the shortlog.
All of these have been in linux-next with no issues for a while"
* tag 'tty-5.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (67 commits)
tty: serial: qcom_geni_serial: Add 51.2MHz frequency support
tty: serial: imx: clear Ageing Timer Interrupt in handler
serial: 8250_fintek: Add F81966 Support
sc16is7xx: Add flag to activate IrDA mode
dt-bindings: sc16is7xx: Add flag to activate IrDA mode
serial: 8250: Support rs485 bus termination GPIO
serial: 8520_port: Fix function param documentation
dt-bindings: serial: Add binding for rs485 bus termination GPIO
vt: keyboard: avoid signed integer overflow in k_ascii
serial: 8250: Enable 16550A variants by default on non-x86
tty: hvc_console, fix crashes on parallel open/close
serial: imx: Initialize lock for non-registered console
sc16is7xx: Read the LSR register for basic device presence check
sc16is7xx: Allow sharing the IRQ line
sc16is7xx: Use threaded IRQ
sc16is7xx: Always use falling edge IRQ
tty: n_gsm: Fix bogus i++ in gsm_data_kick
tty: n_gsm: Remove unnecessary test in gsm_print_packet()
serial: stm32: add no_console_suspend support
tty: serial: fsl_lpuart: Use __maybe_unused instead of #if CONFIG_PM_SLEEP
...
* The remainder of the code necessary to support the Kendryte K210.
* Support for building device trees into the kernel, as the K210 doesn't
have a bootloader that provides one.
* A K210 device tree and the associated defconfig update.
* Support for skipping PMP initialization on systems that trap on PMP
accesses rather than treating them as WARL.
* Support for KGDB.
* Improvements to text patching.
* Some cleanups to the SiFive L2 cache driver.
I may have a second part, but I wanted to get this out earlier rather than
later as they've been ready to go for a while now.
-----BEGIN PGP SIGNATURE-----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=keTq
-----END PGP SIGNATURE-----
Merge tag 'riscv-for-linus-5.8-mw0' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux
Pull RISC-V updates from Palmer Dabbelt:
- The remainder of the code necessary to support the Kendryte K210:
* Support for building device trees into the kernel, as the K210
doesn't have a bootloader that provides one
* A K210 device tree and the associated defconfig update
* Support for skipping PMP initialization on systems that trap on
PMP accesses rather than treating them as WARL
- Support for KGDB
- Improvements to text patching
- Some cleanups to the SiFive L2 cache driver
* tag 'riscv-for-linus-5.8-mw0' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux:
soc: sifive: l2 cache: Mark l2_get_priv_group as static
soc: sifive: l2 cache: Eliminate an unsigned zero compare warning
riscv: Add support to determine no. of L2 cache way enabled
riscv: cacheinfo: Implement cache_get_priv_group with a generic ops structure
riscv: Use text_mutex instead of patch_lock
riscv: Use NOKPROBE_SYMBOL() instead of __krpobes annotation
riscv: Remove the 'riscv_' prefix of function name
riscv: Add SW single-step support for KDB
riscv: Use the XML target descriptions to report 3 system registers
riscv: Add KGDB support
kgdb: Add kgdb_has_hit_break function
RISC-V: Skip setting up PMPs on traps
riscv: K210: Update defconfig
riscv: K210: Add a built-in device tree
riscv: Allow device trees to be built into the kernel
When I combined kgdboc_earlycon with an inflight patch titled ("soc:
qcom-geni-se: Add interconnect support to fix earlycon crash") [1]
things went boom. Specifically I got a crash during the transition
between kgdboc_earlycon and the main kgdboc that looked like this:
Call trace:
__schedule_bug+0x68/0x6c
__schedule+0x75c/0x924
schedule+0x8c/0xbc
schedule_timeout+0x9c/0xfc
do_wait_for_common+0xd0/0x160
wait_for_completion_timeout+0x54/0x74
rpmh_write_batch+0x1fc/0x23c
qcom_icc_bcm_voter_commit+0x1b4/0x388
qcom_icc_set+0x2c/0x3c
apply_constraints+0x5c/0x98
icc_set_bw+0x204/0x3bc
icc_put+0x30/0xf8
geni_remove_earlycon_icc_vote+0x6c/0x9c
qcom_geni_serial_earlycon_exit+0x10/0x1c
kgdboc_earlycon_deinit+0x38/0x58
kgdb_register_io_module+0x11c/0x194
configure_kgdboc+0x108/0x174
kgdboc_probe+0x38/0x60
platform_drv_probe+0x90/0xb0
really_probe+0x130/0x2fc
...
The problem was that we were holding the "kgdb_registration_lock"
while calling into code that didn't expect to be called in spinlock
context.
Let's slightly defer when we call the deinit code so that it's not
done under spinlock.
NOTE: this does mean that the "deinit" call of the old kgdb IO module
is now made _after_ the init of the new IO module, but presumably
that's OK.
[1] https://lkml.kernel.org/r/1588919619-21355-3-git-send-email-akashast@codeaurora.org
Fixes: 220995622d ("kgdboc: Add kgdboc_earlycon to support early kgdb using boot consoles")
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20200526142001.1.I523dc33f96589cb9956f5679976d402c8cda36fa@changeid
[daniel.thompson@linaro.org: Resolved merge issues by hand]
Signed-off-by: Daniel Thompson <daniel.thompson@linaro.org>
The break instruction in RISC-V does not have an immediate value field, so
the kernel cannot identify the purpose of each trap exception through the
opcode. This makes the existing identification schemes in other
architecture unsuitable for the RISC-V kernel. To solve this problem, this
patch adds kgdb_has_hit_break(), which can help RISC-V kernel identify
the KGDB trap exception.
Signed-off-by: Vincent Chen <vincent.chen@sifive.com>
Reviewed-by: Palmer Dabbelt <palmerdabbelt@google.com>
Acked-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Palmer Dabbelt <palmerdabbelt@google.com>
We want to enable kgdb to debug the early parts of the kernel.
Unfortunately kgdb normally is a client of the tty API in the kernel
and serial drivers don't register to the tty layer until fairly late
in the boot process.
Serial drivers do, however, commonly register a boot console. Let's
enable the kgdboc driver to work with boot consoles to provide early
debugging.
This change co-opts the existing read() function pointer that's part
of "struct console". It's assumed that if a boot console (with the
flag CON_BOOT) has implemented read() that both the read() and write()
function are polling functions. That means they work without
interrupts and read() will return immediately (with 0 bytes read) if
there's nothing to read. This should be a safe assumption since it
appears that no current boot consoles implement read() right now and
there seems no reason to do so unless they wanted to support
"kgdboc_earlycon".
The normal/expected way to make all this work is to use
"kgdboc_earlycon" and "kgdboc" together. You should point them both
to the same physical serial connection. At boot time, as the system
transitions from the boot console to the normal console (and registers
a tty), kgdb will switch over.
One awkward part of all this, though, is that there can be a window
where the boot console goes away and we can't quite transtion over to
the main kgdboc that uses the tty layer. There are two main problems:
1. The act of registering the tty doesn't cause any call into kgdboc
so there is a window of time when the tty is there but kgdboc's
init code hasn't been called so we can't transition to it.
2. On some serial drivers the normal console inits (and replaces the
boot console) quite early in the system. Presumably these drivers
were coded up before earlycon worked as well as it does today and
probably they don't need to do this anymore, but it causes us
problems nontheless.
Problem #1 is not too big of a deal somewhat due to the luck of probe
ordering. kgdboc is last in the tty/serial/Makefile so its probe gets
right after all other tty devices. It's not fun to rely on this, but
it does work for the most part.
Problem #2 is a big deal, but only for some serial drivers. Other
serial drivers end up registering the console (which gets rid of the
boot console) and tty at nearly the same time.
The way we'll deal with the window when the system has stopped using
the boot console and the time when we're setup using the tty is to
keep using the boot console. This may sound surprising, but it has
been found to work well in practice. If it doesn't work, it shouldn't
be too hard for a given serial driver to make it keep working.
Specifically, it's expected that the read()/write() function provided
in the boot console should be the same (or nearly the same) as the
normal kgdb polling functions. That means continuing to use them
should work just fine. To make things even more likely to work work
we'll also trap the recently added exit() function in the boot console
we're using and delay any calls to it until we're all done with the
boot console.
NOTE: there could be ways to use all this in weird / unexpected ways.
If you do something like this, it's a bit of a buyer beware situation.
Specifically:
- If you specify only "kgdboc_earlycon" but not "kgdboc" then
(depending on your serial driver) things will probably work OK, but
you'll get a warning printed the first time you use kgdb after the
boot console is gone. You'd only be able to do this, of course, if
the serial driver you're running atop provided an early boot console.
- If your "kgdboc_earlycon" and "kgdboc" devices are not the same
device things should work OK, but it'll be your job to switch over
which device you're monitoring (including figuring out how to switch
over gdb in-flight if you're using it).
When trying to enable "kgdboc_earlycon" it should be noted that the
names that are registered through the boot console layer and the tty
layer are not the same for the same port. For example when debugging
on one board I'd need to pass "kgdboc_earlycon=qcom_geni
kgdboc=ttyMSM0" to enable things properly. Since digging up the boot
console name is a pain and there will rarely be more than one boot
console enabled, you can provide the "kgdboc_earlycon" parameter
without specifying the name of the boot console. In this case we'll
just pick the first boot that implements read() that we find.
This new "kgdboc_earlycon" parameter should be contrasted to the
existing "ekgdboc" parameter. While both provide a way to debug very
early, the usage and mechanisms are quite different. Specifically
"kgdboc_earlycon" is meant to be used in tandem with "kgdboc" and
there is a transition from one to the other. The "ekgdboc" parameter,
on the other hand, replaces the "kgdboc" parameter. It runs the same
logic as the "kgdboc" parameter but just relies on your TTY driver
being present super early. The only known usage of the old "ekgdboc"
parameter is documented as "ekgdboc=kbd earlyprintk=vga". It should
be noted that "kbd" has special treatment allowing it to init early as
a tty device.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Tested-by: Sumit Garg <sumit.garg@linaro.org>
Link: https://lore.kernel.org/r/20200507130644.v4.8.I8fba5961bf452ab92350654aa61957f23ecf0100@changeid
Signed-off-by: Daniel Thompson <daniel.thompson@linaro.org>
If we detect that we recursively entered the debugger we should hack
our I/O ops to NULL so that the panic() in the next line won't
actually cause another recursion into the debugger. The first line of
kgdb_panic() will check this and return.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Daniel Thompson <daniel.thompson@linaro.org>
Link: https://lore.kernel.org/r/20200507130644.v4.6.I89de39f68736c9de610e6f241e68d8dbc44bc266@changeid
Signed-off-by: Daniel Thompson <daniel.thompson@linaro.org>
Using kgdb requires at least some level of architecture-level
initialization. If nothing else, it relies on the architecture to
pass breakpoints / crashes onto kgdb.
On some architectures this all works super early, specifically it
starts working at some point in time before Linux parses
early_params's. On other architectures it doesn't. A survey of a few
platforms:
a) x86: Presumably it all works early since "ekgdboc" is documented to
work here.
b) arm64: Catching crashes works; with a simple patch breakpoints can
also be made to work.
c) arm: Nothing in kgdb works until
paging_init() -> devicemaps_init() -> early_trap_init()
Let's be conservative and, by default, process "kgdbwait" (which tells
the kernel to drop into the debugger ASAP at boot) a bit later at
dbg_late_init() time. If an architecture has tested it and wants to
re-enable super early debugging, they can select the
ARCH_HAS_EARLY_DEBUG KConfig option. We'll do this for x86 to start.
It should be noted that dbg_late_init() is still called quite early in
the system.
Note that this patch doesn't affect when kgdb runs its init. If kgdb
is set to initialize early it will still initialize when parsing
early_param's. This patch _only_ inhibits the initial breakpoint from
"kgdbwait". This means:
* Without any extra patches arm64 platforms will at least catch
crashes after kgdb inits.
* arm platforms will catch crashes (and could handle a hardcoded
kgdb_breakpoint()) any time after early_trap_init() runs, even
before dbg_late_init().
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Borislav Petkov <bp@alien8.de>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: https://lore.kernel.org/r/20200507130644.v4.4.I3113aea1b08d8ce36dc3720209392ae8b815201b@changeid
Signed-off-by: Daniel Thompson <daniel.thompson@linaro.org>
In commit 81eaadcae8 ("kgdboc: disable the console lock when in
kgdb") we avoided the WARN_CONSOLE_UNLOCKED() yell when we were in
kgdboc. That still works fine, but it turns out that we get a similar
yell when using other I/O drivers. One example is the "I/O driver"
for the kgdb test suite (kgdbts). When I enabled that I again got the
same yells.
Even though "kgdbts" doesn't actually interact with the user over the
console, using it still causes kgdb to print to the consoles. That
trips the same warning:
con_is_visible+0x60/0x68
con_scroll+0x110/0x1b8
lf+0x4c/0xc8
vt_console_print+0x1b8/0x348
vkdb_printf+0x320/0x89c
kdb_printf+0x68/0x90
kdb_main_loop+0x190/0x860
kdb_stub+0x2cc/0x3ec
kgdb_cpu_enter+0x268/0x744
kgdb_handle_exception+0x1a4/0x200
kgdb_compiled_brk_fn+0x34/0x44
brk_handler+0x7c/0xb8
do_debug_exception+0x1b4/0x228
Let's increment/decrement the "ignore_console_lock_warning" variable
all the time when we enter the debugger.
This will allow us to later revert commit 81eaadcae8 ("kgdboc:
disable the console lock when in kgdb").
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Daniel Thompson <daniel.thompson@linaro.org>
Link: https://lore.kernel.org/r/20200507130644.v4.1.Ied2b058357152ebcc8bf68edd6f20a11d98d7d4e@changeid
Signed-off-by: Daniel Thompson <daniel.thompson@linaro.org>
With earlier commits, the API no longer discards the const-ness of the
sysrq_key_op. As such we can add the notation.
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jslaby@suse.com>
Cc: linux-kernel@vger.kernel.org
Cc: Jason Wessel <jason.wessel@windriver.com>
Cc: Daniel Thompson <daniel.thompson@linaro.org>
Cc: kgdb-bugreport@lists.sourceforge.net
Acked-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Emil Velikov <emil.l.velikov@gmail.com>
Link: https://lore.kernel.org/r/20200513214351.2138580-9-emil.l.velikov@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Kernel doc does not understand POD variables to be referred to.
.../debug_core.c:73: warning: cannot understand function prototype:
'int kgdb_connected; '
Convert kernel doc to pure comment.
Fixes: dc7d552705 ("kgdb: core")
Cc: Jason Wessel <jason.wessel@windriver.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Daniel Thompson <daniel.thompson@linaro.org>
Recent versions of gcc (reported on gcc-7.4) issue array subscript
warnings for builds where SMP is not enabled.
kernel/debug/debug_core.c: In function 'kdb_dump_stack_on_cpu':
kernel/debug/debug_core.c:452:17: warning: array subscript is outside array
+bounds [-Warray-bounds]
if (!(kgdb_info[cpu].exception_state & DCPU_IS_SLAVE)) {
~~~~~~~~~^~~~~
kernel/debug/debug_core.c:469:33: warning: array subscript is outside array
+bounds [-Warray-bounds]
kgdb_info[cpu].exception_state |= DCPU_WANT_BT;
kernel/debug/debug_core.c:470:18: warning: array subscript is outside array
+bounds [-Warray-bounds]
while (kgdb_info[cpu].exception_state & DCPU_WANT_BT)
There is no bug here but there is scope to improve the code
generation for non-SMP systems (whilst also silencing the warning).
Reported-by: kbuild test robot <lkp@intel.com>
Fixes: 2277b49258 ("kdb: Fix stack crawling on 'running' CPUs that aren't the master")
Signed-off-by: Daniel Thompson <daniel.thompson@linaro.org>
Link: https://lore.kernel.org/r/20191021101057.23861-1-daniel.thompson@linaro.org
Reviewed-by: Douglas Anderson <dianders@chromium.org>
In kdb when you do 'btc' (back trace on CPU) it doesn't necessarily
give you the right info. Specifically on many architectures
(including arm64, where I tested) you can't dump the stack of a
"running" process that isn't the process running on the current CPU.
This can be seen by this:
echo SOFTLOCKUP > /sys/kernel/debug/provoke-crash/DIRECT
# wait 2 seconds
<sysrq>g
Here's what I see now on rk3399-gru-kevin. I see the stack crawl for
the CPU that handled the sysrq but everything else just shows me stuck
in __switch_to() which is bogus:
======
[0]kdb> btc
btc: cpu status: Currently on cpu 0
Available cpus: 0, 1-3(I), 4, 5(I)
Stack traceback for pid 0
0xffffff801101a9c0 0 0 1 0 R 0xffffff801101b3b0 *swapper/0
Call trace:
dump_backtrace+0x0/0x138
...
kgdb_compiled_brk_fn+0x34/0x44
...
sysrq_handle_dbg+0x34/0x5c
Stack traceback for pid 0
0xffffffc0f175a040 0 0 1 1 I 0xffffffc0f175aa30 swapper/1
Call trace:
__switch_to+0x1e4/0x240
0xffffffc0f65616c0
Stack traceback for pid 0
0xffffffc0f175d040 0 0 1 2 I 0xffffffc0f175da30 swapper/2
Call trace:
__switch_to+0x1e4/0x240
0xffffffc0f65806c0
Stack traceback for pid 0
0xffffffc0f175b040 0 0 1 3 I 0xffffffc0f175ba30 swapper/3
Call trace:
__switch_to+0x1e4/0x240
0xffffffc0f659f6c0
Stack traceback for pid 1474
0xffffffc0dde8b040 1474 727 1 4 R 0xffffffc0dde8ba30 bash
Call trace:
__switch_to+0x1e4/0x240
__schedule+0x464/0x618
0xffffffc0dde8b040
Stack traceback for pid 0
0xffffffc0f17b0040 0 0 1 5 I 0xffffffc0f17b0a30 swapper/5
Call trace:
__switch_to+0x1e4/0x240
0xffffffc0f65dd6c0
===
The problem is that 'btc' eventually boils down to
show_stack(task_struct, NULL);
...and show_stack() doesn't work for "running" CPUs because their
registers haven't been stashed.
On x86 things might work better (I haven't tested) because kdb has a
special case for x86 in kdb_show_stack() where it passes the stack
pointer to show_stack(). This wouldn't work on arm64 where the stack
crawling function seems needs the "fp" and "pc", not the "sp" which is
presumably why arm64's show_stack() function totally ignores the "sp"
parameter.
NOTE: we _can_ get a good stack dump for all the cpus if we manually
switch each one to the kdb master and do a back trace. AKA:
cpu 4
bt
...will give the expected trace. That's because now arm64's
dump_backtrace will now see that "tsk == current" and go through a
different path.
In this patch I fix the problems by catching a request to stack crawl
a task that's running on a CPU and then I ask that CPU to do the stack
crawl.
NOTE: this will (presumably) change what stack crawls are printed for
x86 machines. Now kdb functions will show up in the stack crawl.
Presumably this is OK but if it's not we can go back and add a special
case for x86 again.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Acked-by: Will Deacon <will@kernel.org>
Signed-off-by: Daniel Thompson <daniel.thompson@linaro.org>
Right now kgdb/kdb hooks up to debug panics by registering for the panic
notifier. This works OK except that it means that kgdb/kdb gets called
_after_ the CPUs in the system are taken offline. That means that if
anything important was happening on those CPUs (like something that might
have contributed to the panic) you can't debug them.
Specifically I ran into a case where I got a panic because a task was
"blocked for more than 120 seconds" which was detected on CPU 2. I nicely
got shown stack traces in the kernel log for all CPUs including CPU 0,
which was running 'PID: 111 Comm: kworker/0:1H' and was in the middle of
__mmc_switch().
I then ended up at the kdb prompt where switched over to kgdb to try to
look at local variables of the process on CPU 0. I found that I couldn't.
Digging more, I found that I had no info on any tasks running on CPUs
other than CPU 2 and that asking kdb for help showed me "Error: no saved
data for this cpu". This was because all the CPUs were offline.
Let's move the entry of kdb/kgdb to a direct call from panic() and stop
using the generic notifier. Putting a direct call in allows us to order
things more properly and it also doesn't seem like we're breaking any
abstractions by calling into the debugger from the panic function.
Daniel said:
: This patch changes the way kdump and kgdb interact with each other.
: However it would seem rather odd to have both tools simultaneously armed
: and, even if they were, the user still has the option to use panic_timeout
: to force a kdump to happen. Thus I think the change of order is
: acceptable.
Link: http://lkml.kernel.org/r/20190703170354.217312-1-dianders@chromium.org
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Daniel Thompson <daniel.thompson@linaro.org>
Cc: Jason Wessel <jason.wessel@windriver.com>
Cc: Kees Cook <keescook@chromium.org>
Cc: Borislav Petkov <bp@suse.de>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Feng Tang <feng.tang@intel.com>
Cc: YueHaibing <yuehaibing@huawei.com>
Cc: Sergey Senozhatsky <sergey.senozhatsky.work@gmail.com>
Cc: "Steven Rostedt (VMware)" <rostedt@goodmis.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The comment that says that module_event() is not static is clearly
wrong.
Signed-off-by: Nadav Amit <namit@vmware.com>
Signed-off-by: Daniel Thompson <daniel.thompson@linaro.org>
If you have a CPU that fails to round up and then run 'btc' you'll end
up crashing in kdb becaue we dereferenced NULL. Let's add a check.
It's wise to also set the task to NULL when leaving the debugger so
that if we fail to round up on a later entry into the debugger we
won't backtrace a stale task.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Acked-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Daniel Thompson <daniel.thompson@linaro.org>
If we're using the default implementation of kgdb_roundup_cpus() that
uses smp_call_function_single_async() we can end up hanging
kgdb_roundup_cpus() if we try to round up a CPU that failed to round
up before.
Specifically smp_call_function_single_async() will try to wait on the
csd lock for the CPU that we're trying to round up. If the previous
round up never finished then that lock could still be held and we'll
just sit there hanging.
There's not a lot of use trying to round up a CPU that failed to round
up before. Let's keep a flag that indicates whether the CPU started
but didn't finish to round up before. If we see that flag set then
we'll skip the next round up.
In general we have a few goals here:
- We never want to end up calling smp_call_function_single_async()
when the csd is still locked. This is accomplished because
flush_smp_call_function_queue() unlocks the csd _before_ invoking
the callback. That means that when kgdb_nmicallback() runs we know
for sure the the csd is no longer locked. Thus when we set
"rounding_up = false" we know for sure that the csd is unlocked.
- If there are no timeouts rounding up we should never skip a round
up.
NOTE #1: In general trying to continue running after failing to round
up CPUs doesn't appear to be supported in the debugger. When I
simulate this I find that kdb reports "Catastrophic error detected"
when I try to continue. I can overrule and continue anyway, but it
should be noted that we may be entering the land of dragons here.
Possibly the "Catastrophic error detected" was added _because_ of the
future failure to round up, but even so this is an area of the code
that hasn't been strongly tested.
NOTE #2: I did a bit of testing before and after this change. I
introduced a 10 second hang in the kernel while holding a spinlock
that I could invoke on a certain CPU with 'taskset -c 3 cat /sys/...".
Before this change if I did:
- Invoke hang
- Enter debugger
- g (which warns about Catastrophic error, g again to go anyway)
- g
- Enter debugger
...I'd hang the rest of the 10 seconds without getting a debugger
prompt. After this change I end up in the debugger the 2nd time after
only 1 second with the standard warning about 'Timed out waiting for
secondary CPUs.'
I'll also note that once the CPU finished waiting I could actually
debug it (aka "btc" worked)
I won't promise that everything works perfectly if the errant CPU
comes back at just the wrong time (like as we're entering or exiting
the debugger) but it certainly seems like an improvement.
NOTE #3: setting 'kgdb_info[cpu].rounding_up = false' is in
kgdb_nmicallback() instead of kgdb_call_nmi_hook() because some
implementations override kgdb_call_nmi_hook(). It shouldn't hurt to
have it in kgdb_nmicallback() in any case.
NOTE #4: this logic is really only needed because there is no API call
like "smp_try_call_function_single_async()" or "smp_csd_is_locked()".
If such an API existed then we'd use it instead, but it seemed a bit
much to add an API like this just for kgdb.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Acked-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Daniel Thompson <daniel.thompson@linaro.org>
When I had lockdep turned on and dropped into kgdb I got a nice splat
on my system. Specifically it hit:
DEBUG_LOCKS_WARN_ON(current->hardirq_context)
Specifically it looked like this:
sysrq: SysRq : DEBUG
------------[ cut here ]------------
DEBUG_LOCKS_WARN_ON(current->hardirq_context)
WARNING: CPU: 0 PID: 0 at .../kernel/locking/lockdep.c:2875 lockdep_hardirqs_on+0xf0/0x160
CPU: 0 PID: 0 Comm: swapper/0 Not tainted 4.19.0 #27
pstate: 604003c9 (nZCv DAIF +PAN -UAO)
pc : lockdep_hardirqs_on+0xf0/0x160
...
Call trace:
lockdep_hardirqs_on+0xf0/0x160
trace_hardirqs_on+0x188/0x1ac
kgdb_roundup_cpus+0x14/0x3c
kgdb_cpu_enter+0x53c/0x5cc
kgdb_handle_exception+0x180/0x1d4
kgdb_compiled_brk_fn+0x30/0x3c
brk_handler+0x134/0x178
do_debug_exception+0xfc/0x178
el1_dbg+0x18/0x78
kgdb_breakpoint+0x34/0x58
sysrq_handle_dbg+0x54/0x5c
__handle_sysrq+0x114/0x21c
handle_sysrq+0x30/0x3c
qcom_geni_serial_isr+0x2dc/0x30c
...
...
irq event stamp: ...45
hardirqs last enabled at (...44): [...] __do_softirq+0xd8/0x4e4
hardirqs last disabled at (...45): [...] el1_irq+0x74/0x130
softirqs last enabled at (...42): [...] _local_bh_enable+0x2c/0x34
softirqs last disabled at (...43): [...] irq_exit+0xa8/0x100
---[ end trace adf21f830c46e638 ]---
Looking closely at it, it seems like a really bad idea to be calling
local_irq_enable() in kgdb_roundup_cpus(). If nothing else that seems
like it could violate spinlock semantics and cause a deadlock.
Instead, let's use a private csd alongside
smp_call_function_single_async() to round up the other CPUs. Using
smp_call_function_single_async() doesn't require interrupts to be
enabled so we can remove the offending bit of code.
In order to avoid duplicating this across all the architectures that
use the default kgdb_roundup_cpus(), we'll add a "weak" implementation
to debug_core.c.
Looking at all the people who previously had copies of this code,
there were a few variants. I've attempted to keep the variants
working like they used to. Specifically:
* For arch/arc we passed NULL to kgdb_nmicallback() instead of
get_irq_regs().
* For arch/mips there was a bit of extra code around
kgdb_nmicallback()
NOTE: In this patch we will still get into trouble if we try to round
up a CPU that failed to round up before. We'll try to round it up
again and potentially hang when we try to grab the csd lock. That's
not new behavior but we'll still try to do better in a future patch.
Suggested-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Cc: Vineet Gupta <vgupta@synopsys.com>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Richard Kuo <rkuo@codeaurora.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Paul Burton <paul.burton@mips.com>
Cc: James Hogan <jhogan@kernel.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Cc: Rich Felker <dalias@libc.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Daniel Thompson <daniel.thompson@linaro.org>
The function kgdb_roundup_cpus() was passed a parameter that was
documented as:
> the flags that will be used when restoring the interrupts. There is
> local_irq_save() call before kgdb_roundup_cpus().
Nobody used those flags. Anyone who wanted to temporarily turn on
interrupts just did local_irq_enable() and local_irq_disable() without
looking at them. So we can definitely remove the flags.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Cc: Vineet Gupta <vgupta@synopsys.com>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Richard Kuo <rkuo@codeaurora.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Paul Burton <paul.burton@mips.com>
Cc: James Hogan <jhogan@kernel.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Cc: Rich Felker <dalias@libc.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Daniel Thompson <daniel.thompson@linaro.org>
We are going to move softlockup APIs out of <linux/sched.h>, which
will have to be picked up from other headers and a couple of .c files.
<linux/nmi.h> already includes <linux/sched.h>.
Include the <linux/nmi.h> header in the files that are going to need it.
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
The <linux/sched.h> header includes various vmacache related defines,
which are arguably misplaced.
Move them to mm_types.h and minimize the sched.h impact by putting
all task vmacache state into a new 'struct vmacache' structure.
No change in functionality.
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
We've got a delay loop waiting for secondary CPUs. That loop uses
loops_per_jiffy. However, loops_per_jiffy doesn't actually mean how
many tight loops make up a jiffy on all architectures. It is quite
common to see things like this in the boot log:
Calibrating delay loop (skipped), value calculated using timer
frequency.. 48.00 BogoMIPS (lpj=24000)
In my case I was seeing lots of cases where other CPUs timed out
entering the debugger only to print their stack crawls shortly after the
kdb> prompt was written.
Elsewhere in kgdb we already use udelay(), so that should be safe enough
to use to implement our timeout. We'll delay 1 ms for 1000 times, which
should give us a full second of delay (just like the old code wanted)
but allow us to notice that we're done every 1 ms.
[akpm@linux-foundation.org: simplifications, per Daniel]
Link: http://lkml.kernel.org/r/1477091361-2039-1-git-send-email-dianders@chromium.org
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Daniel Thompson <daniel.thompson@linaro.org>
Cc: Jason Wessel <jason.wessel@windriver.com>
Cc: Brian Norris <briannorris@chromium.org>
Cc: <stable@vger.kernel.org> [4.0+]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
On non-developer devices, kgdb prevents the device from rebooting
after a panic.
Incase of panics and exceptions, to allow the device to reboot, prevent
entering debug mode to avoid getting stuck waiting for the user to
interact with debugger.
To avoid entering the debugger on panic/exception without any extra
configuration, panic_timeout is being used which can be set via
/proc/sys/kernel/panic at run time and CONFIG_PANIC_TIMEOUT sets the
default value.
Setting panic_timeout indicates that the user requested machine to
perform unattended reboot after panic. We dont want to get stuck waiting
for the user input incase of panic.
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: kgdb-bugreport@lists.sourceforge.net
Cc: linux-kernel@vger.kernel.org
Cc: Android Kernel Team <kernel-team@android.com>
Cc: John Stultz <john.stultz@linaro.org>
Cc: Sumit Semwal <sumit.semwal@linaro.org>
Signed-off-by: Colin Cross <ccross@android.com>
[Kiran: Added context to commit message.
panic_timeout is used instead of break_on_panic and
break_on_exception to honor CONFIG_PANIC_TIMEOUT
Modified the commit as per community feedback]
Signed-off-by: Kiran Raparthy <kiran.kumar@linaro.org>
Signed-off-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
There was a follow on replacement patch against the prior
"kgdb: Timeout if secondary CPUs ignore the roundup".
See: https://lkml.org/lkml/2015/1/7/442
This patch is the delta vs the patch that was committed upstream:
* Fix an off-by-one error in kdb_cpu().
* Replace NR_CPUS with CONFIG_NR_CPUS to tell checkpatch that we
really want a static limit.
* Removed the "KGDB: " prefix from the pr_crit() in debug_core.c
(kgdb-next contains a patch which introduced pr_fmt() to this file
to the tag will now be applied automatically).
Cc: Daniel Thompson <daniel.thompson@linaro.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
-Convert printk( to pr_foo()
-Add pr_fmt
-Coalesce formats
Cc: Jason Wessel <jason.wessel@windriver.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Joe Perches <joe@perches.com>
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
Currently if an active CPU fails to respond to a roundup request the CPU
that requested the roundup will become stuck. This needlessly reduces the
robustness of the debugger.
This patch introduces a timeout allowing the system state to be examined
even when the system contains unresponsive processors. It also modifies
kdb's cpu command to make it censor attempts to switch to unresponsive
processors and to report their state as (D)ead.
Signed-off-by: Daniel Thompson <daniel.thompson@linaro.org>
Cc: Jason Wessel <jason.wessel@windriver.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
This patch is a continuation of efforts trying to optimize find_vma(),
avoiding potentially expensive rbtree walks to locate a vma upon faults.
The original approach (https://lkml.org/lkml/2013/11/1/410), where the
largest vma was also cached, ended up being too specific and random,
thus further comparison with other approaches were needed. There are
two things to consider when dealing with this, the cache hit rate and
the latency of find_vma(). Improving the hit-rate does not necessarily
translate in finding the vma any faster, as the overhead of any fancy
caching schemes can be too high to consider.
We currently cache the last used vma for the whole address space, which
provides a nice optimization, reducing the total cycles in find_vma() by
up to 250%, for workloads with good locality. On the other hand, this
simple scheme is pretty much useless for workloads with poor locality.
Analyzing ebizzy runs shows that, no matter how many threads are
running, the mmap_cache hit rate is less than 2%, and in many situations
below 1%.
The proposed approach is to replace this scheme with a small per-thread
cache, maximizing hit rates at a very low maintenance cost.
Invalidations are performed by simply bumping up a 32-bit sequence
number. The only expensive operation is in the rare case of a seq
number overflow, where all caches that share the same address space are
flushed. Upon a miss, the proposed replacement policy is based on the
page number that contains the virtual address in question. Concretely,
the following results are seen on an 80 core, 8 socket x86-64 box:
1) System bootup: Most programs are single threaded, so the per-thread
scheme does improve ~50% hit rate by just adding a few more slots to
the cache.
+----------------+----------+------------------+
| caching scheme | hit-rate | cycles (billion) |
+----------------+----------+------------------+
| baseline | 50.61% | 19.90 |
| patched | 73.45% | 13.58 |
+----------------+----------+------------------+
2) Kernel build: This one is already pretty good with the current
approach as we're dealing with good locality.
+----------------+----------+------------------+
| caching scheme | hit-rate | cycles (billion) |
+----------------+----------+------------------+
| baseline | 75.28% | 11.03 |
| patched | 88.09% | 9.31 |
+----------------+----------+------------------+
3) Oracle 11g Data Mining (4k pages): Similar to the kernel build workload.
+----------------+----------+------------------+
| caching scheme | hit-rate | cycles (billion) |
+----------------+----------+------------------+
| baseline | 70.66% | 17.14 |
| patched | 91.15% | 12.57 |
+----------------+----------+------------------+
4) Ebizzy: There's a fair amount of variation from run to run, but this
approach always shows nearly perfect hit rates, while baseline is just
about non-existent. The amounts of cycles can fluctuate between
anywhere from ~60 to ~116 for the baseline scheme, but this approach
reduces it considerably. For instance, with 80 threads:
+----------------+----------+------------------+
| caching scheme | hit-rate | cycles (billion) |
+----------------+----------+------------------+
| baseline | 1.06% | 91.54 |
| patched | 99.97% | 14.18 |
+----------------+----------+------------------+
[akpm@linux-foundation.org: fix nommu build, per Davidlohr]
[akpm@linux-foundation.org: document vmacache_valid() logic]
[akpm@linux-foundation.org: attempt to untangle header files]
[akpm@linux-foundation.org: add vmacache_find() BUG_ON]
[hughd@google.com: add vmacache_valid_mm() (from Oleg)]
[akpm@linux-foundation.org: coding-style fixes]
[akpm@linux-foundation.org: adjust and enhance comments]
Signed-off-by: Davidlohr Bueso <davidlohr@hp.com>
Reviewed-by: Rik van Riel <riel@redhat.com>
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Reviewed-by: Michel Lespinasse <walken@google.com>
Cc: Oleg Nesterov <oleg@redhat.com>
Tested-by: Hugh Dickins <hughd@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The function kgdb_breakpoint() sets up break point at
compile time by calling arch_kgdb_breakpoint();
Though this call is surrounded by wmb() barrier,
the compile can still re-order the break point,
because this scheduling barrier is not a code motion
barrier in gcc.
Making kgdb_breakpoint() as noinline solves this problem
of code reording around break point instruction and also
avoids problem of being called as inline function from
other places
More details about discussion on this can be found here
http://comments.gmane.org/gmane.linux.ports.arm.kernel/269732
Signed-off-by: Vijaya Kumar K <Vijaya.Kumar@caviumnetworks.com>
Acked-by: Will Deacon <will.deacon@arm.com>
Acked-by: Jason Wessel <jason.wessel@windriver.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Some code added to the debug_core module had KDB dependencies
that it shouldn't have. Move the KDB dependent REASON back to
the caller to remove the dependency in the debug core code.
Update the call from the UV NMI handler to conform to the new
interface.
Signed-off-by: Mike Travis <travis@sgi.com>
Reviewed-by: Hedi Berriche <hedi@sgi.com>
Cc: Russ Anderson <rja@sgi.com>
Cc: Jason Wessel <jason.wessel@windriver.com>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Arnaldo Carvalho de Melo <acme@ghostprotocols.net>
Link: http://lkml.kernel.org/r/20140114162551.318251993@asylum.americas.sgi.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
This patch adds a kgdb_nmicallin() interface that can be used by
external NMI handlers to call the KGDB/KDB handler. The primary
need for this is for those types of NMI interrupts where all the
CPUs have already received the NMI signal. Therefore no
send_IPI(NMI) is required, and in fact it will cause a 2nd
unhandled NMI to occur. This generates the "Dazed and Confuzed"
messages.
Since all the CPUs are getting the NMI at roughly the same time,
it's not guaranteed that the first CPU that hits the NMI handler
will manage to enter KGDB and set the dbg_master_lock before the
slaves start entering. The new argument "send_ready" was added
for KGDB to signal the NMI handler to release the slave CPUs for
entry into KGDB.
Signed-off-by: Mike Travis <travis@sgi.com>
Acked-by: Jason Wessel <jason.wessel@windriver.com>
Reviewed-by: Dimitri Sivanich <sivanich@sgi.com>
Reviewed-by: Hedi Berriche <hedi@sgi.com>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Arnaldo Carvalho de Melo <acme@ghostprotocols.net>
Link: http://lkml.kernel.org/r/20131002151417.928886849@asylum.americas.sgi.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Currently help message of /proc/sysrq-trigger highlight its upper-case
characters, like below:
SysRq : HELP : loglevel(0-9) reBoot Crash terminate-all-tasks(E)
memory-full-oom-kill(F) kill-all-tasks(I) ...
this would confuse user trigger sysrq by upper-case character, which is
inconsistent with the real lower-case character registed key.
This inconsistent help message will also lead more confused when
26 upper-case letters put into use in future.
This patch fix kgdb sysrq key: "debug(g)"
Signed-off-by: zhangwei(Jovi) <jovi.zhangwei@huawei.com>
Cc: Jason Wessel <jason.wessel@windriver.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
There's no reason kgdb.h itself needs to include the 8250 serial port
header file. So push it down to the _very_ limited number of individual
drivers that need the values in that file, and fix up the places where
people really wanted serial_core.h and platform_device.h.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cleanups
Clean up compile warnings in kgdboc.c and x86/kernel/kgdb.c
Add module event hooks for simplified debugging with gdb
Fixes
Fix kdb to stop paging with 'q' on bta and dmesg
Fix for data that scrolls off the vga console due to line wrapping
when using the kdb pager
New
The debug core registers for kernel module events which allows a
kernel aware gdb to automatically load symbols and break on entry
to a kernel module
Allow kgdboc=kdb to setup kdb on the vga console
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=uf0L
-----END PGP SIGNATURE-----
Merge tag 'for_linus-3.7' of git://git.kernel.org/pub/scm/linux/kernel/git/jwessel/kgdb
Pull KGDB/KDB fixes and cleanups from Jason Wessel:
"Cleanups
- Clean up compile warnings in kgdboc.c and x86/kernel/kgdb.c
- Add module event hooks for simplified debugging with gdb
Fixes
- Fix kdb to stop paging with 'q' on bta and dmesg
- Fix for data that scrolls off the vga console due to line wrapping
when using the kdb pager
New
- The debug core registers for kernel module events which allows a
kernel aware gdb to automatically load symbols and break on entry
to a kernel module
- Allow kgdboc=kdb to setup kdb on the vga console"
* tag 'for_linus-3.7' of git://git.kernel.org/pub/scm/linux/kernel/git/jwessel/kgdb:
tty/console: fix warnings in drivers/tty/serial/kgdboc.c
kdb,vt_console: Fix missed data due to pager overruns
kdb: Fix dmesg/bta scroll to quit with 'q'
kgdboc: Accept either kbd or kdb to activate the vga + keyboard kdb shell
kgdb,x86: fix warning about unused variable
mips,kgdb: fix recursive page fault with CONFIG_KPROBES
kgdb: Add module event hooks
Liam R. Howlett
Daniel Thompson
Cai Huoqing
Gustavo A. R. Silva
Zhen Lei
Sumit Garg
Lukas Bulwahn
Peter Zijlstra
Youling Tang
Douglas Anderson
Kees Cook
Christoph Hellwig
Linus Torvalds
Vincent Chen
Emil Velikov
Andy Shevchenko
Nadav Amit
Ingo Molnar
Colin Cross
Jason Wessel
Fabian Frederick
Davidlohr Bueso
Vijaya Kumar K
Mike Travis
zhangwei(Jovi)
Greg Kroah-Hartman