NLM_F_MULTI must be used only when a NLMSG_DONE message is sent. In fact,
it is sent only at the end of a dump.
Libraries like libnl will wait forever for NLMSG_DONE.
Fixes: e5a55a8987 ("net: create generic bridge ops")
Fixes: 815cccbf10 ("ixgbe: add setlink, getlink support to ixgbe and ixgbevf")
CC: John Fastabend <john.r.fastabend@intel.com>
CC: Sathya Perla <sathya.perla@emulex.com>
CC: Subbu Seetharaman <subbu.seetharaman@emulex.com>
CC: Ajit Khaparde <ajit.khaparde@emulex.com>
CC: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
CC: intel-wired-lan@lists.osuosl.org
CC: Jiri Pirko <jiri@resnulli.us>
CC: Scott Feldman <sfeldma@gmail.com>
CC: Stephen Hemminger <stephen@networkplumber.org>
CC: bridge@lists.linux-foundation.org
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
NLM_F_MULTI must be used only when a NLMSG_DONE message is sent. In fact,
it is sent only at the end of a dump.
Libraries like libnl will wait forever for NLMSG_DONE.
Fixes: 37a393bc49 ("bridge: notify mdb changes via netlink")
CC: Cong Wang <amwang@redhat.com>
CC: Stephen Hemminger <stephen@networkplumber.org>
CC: bridge@lists.linux-foundation.org
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Switch the nf_tables registers from 128 bit addressing to 32 bit
addressing to support so called concatenations, where multiple values
can be concatenated over multiple registers for O(1) exact matches of
multiple dimensions using sets.
The old register values are mapped to areas of 128 bits for compatibility.
When dumping register numbers, values are expressed using the old values
if they refer to the beginning of a 128 bit area for compatibility.
To support concatenations, register loads of less than a full 32 bit
value need to be padded. This mainly affects the payload and exthdr
expressions, which both unconditionally zero the last word before
copying the data.
Userspace fully passes the testsuite using both old and new register
addressing.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Add helper functions to parse and dump register values in netlink attributes.
These helpers will later be changed to take care of translation between the
old 128 bit and the new 32 bit register numbers.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Simple conversion to use u32 pointers to the beginning of the registers
to keep follow up patches smaller.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Replace the array of registers passed to expressions by a struct nft_regs,
containing the verdict as a seperate member, which aliases to the
NFT_REG_VERDICT register.
This is needed to seperate the verdict from the data registers completely,
so their size can be changed.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
All users of nft_validate_register_store() first invoke
nft_validate_output_register(). There is in fact no use for using it
on its own, so simplify the code by folding the functionality into
nft_validate_register_store() and kill it.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
The existing name is ambiguous, data is loaded as well when we read from
a register. Rename to nft_validate_register_store() for clarity and
consistency with the upcoming patch to introduce its counterpart,
nft_validate_register_load().
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
For values spanning multiple registers, we need to validate that enough
space is available from the destination register onwards. Add a len
argument to nft_validate_data_load() and consolidate the existing length
validations in preparation of that.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Pablo Neira Ayuso says:
====================
Netfilter updates for net-next
The following patchset contains Netfilter updates for your net-next tree.
They are:
* nf_tables set timeout infrastructure from Patrick Mchardy.
1) Add support for set timeout support.
2) Add support for set element timeouts using the new set extension
infrastructure.
4) Add garbage collection helper functions to get rid of stale elements.
Elements are accumulated in a batch that are asynchronously released
via RCU when the batch is full.
5) Add garbage collection synchronization helpers. This introduces a new
element busy bit to address concurrent access from the netlink API and the
garbage collector.
5) Add timeout support for the nft_hash set implementation. The garbage
collector peridically checks for stale elements from the workqueue.
* iptables/nftables cgroup fixes:
6) Ignore non full-socket objects from the input path, otherwise cgroup
match may crash, from Daniel Borkmann.
7) Fix cgroup in nf_tables.
8) Save some cycles from xt_socket by skipping packet header parsing when
skb->sk is already set because of early demux. Also from Daniel.
* br_netfilter updates from Florian Westphal.
9) Save frag_max_size and restore it from the forward path too.
10) Use a per-cpu area to restore the original source MAC address when traffic
is DNAT'ed.
11) Add helper functions to access physical devices.
12) Use these new physdev helper function from xt_physdev.
13) Add another nf_bridge_info_get() helper function to fetch the br_netfilter
state information.
14) Annotate original layer 2 protocol number in nf_bridge info, instead of
using kludgy flags.
15) Also annotate the pkttype mangling when the packet travels back and forth
from the IP to the bridge layer, instead of using a flag.
* More nf_tables set enhancement from Patrick:
16) Fix possible usage of set variant that doesn't support timeouts.
17) Avoid spurious "set is full" errors from Netlink API when there are pending
stale elements scheduled to be released.
18) Restrict loop checks to set maps.
19) Add support for dynamic set updates from the packet path.
20) Add support to store optional user data (eg. comments) per set element.
BTW, I have also pulled net-next into nf-next to anticipate the conflict
resolution between your okfn() signature changes and Florian's br_netfilter
updates.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
More recent GCC warns about two kinds of switch statement uses:
1) Switching on an enumeration, but not having an explicit case
statement for all members of the enumeration. To show the
compiler this is intentional, we simply add a default case
with nothing more than a break statement.
2) Switching on a boolean value. I think this warning is dumb
but nevertheless you get it wholesale with -Wswitch.
This patch cures all such warnings in netfilter.
Signed-off-by: David S. Miller <davem@davemloft.net>
Acked-by: Pablo Neira Ayuso <pablo@netfilter.org>
nf_bridge_info->mask is used for several things, for example to
remember if skb->pkt_type was set to OTHER_HOST.
For a bridge, OTHER_HOST is expected case. For ip forward its a non-starter
though -- routing expects PACKET_HOST.
Bridge netfilter thus changes OTHER_HOST to PACKET_HOST before hook
invocation and then un-does it after hook traversal.
This information is irrelevant outside of br_netfilter.
After this change, ->mask now only contains flags that need to be
known outside of br_netfilter in fast-path.
Future patch changes mask into a 2bit state field in sk_buff, so that
we can remove skb->nf_bridge pointer for good and consider all remaining
places that access nf_bridge info content a not-so fastpath.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
->mask is a bit info field that mixes various use cases.
In particular, we have flags that are mutually exlusive, and flags that
are only used within br_netfilter while others need to be exposed to
other parts of the kernel.
Remove BRNF_8021Q/PPPoE flags. They're mutually exclusive and only
needed within br_netfilter context.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Don't access skb->nf_bridge directly, this pointer will be removed soon.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
br_netfilter maintains an extra state, nf_bridge_info, which is attached
to skb via skb->nf_bridge pointer.
Amongst other things we use skb->nf_bridge->data to store the original
mac header for every processed skb.
This is required for ip refragmentation when using conntrack
on top of bridge, because ip_fragment doesn't copy it from original skb.
However there is no need anymore to do this unconditionally.
Move this to the one place where its needed -- when br_netfilter calls
ip_fragment().
Also switch to percpu storage for this so we can handle fragmenting
without accessing nf_bridge meta data.
Only user left is neigh resolution when DNAT is detected, to hold
the original source mac address (neigh resolution builds new mac header
using bridge mac), so rename ->data and reduce its size to whats needed.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
On the output paths in particular, we have to sometimes deal with two
socket contexts. First, and usually skb->sk, is the local socket that
generated the frame.
And second, is potentially the socket used to control a tunneling
socket, such as one the encapsulates using UDP.
We do not want to disassociate skb->sk when encapsulating in order
to fix this, because that would break socket memory accounting.
The most extreme case where this can cause huge problems is an
AF_PACKET socket transmitting over a vxlan device. We hit code
paths doing checks that assume they are dealing with an ipv4
socket, but are actually operating upon the AF_PACKET one.
Signed-off-by: David S. Miller <davem@davemloft.net>
The goal of this patch is to prepare the removal of the iflink field. It
introduces a new ndo function, which will be implemented by virtual interfaces.
There is no functional change into this patch. All readers of iflink field
now call dev_get_iflink().
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We also need to save/store in forward, else br_parse_ip_options call
will zero frag_max_size as well.
Fixes: 93fdd47e5 ('bridge: Save frag_max_size between PRE_ROUTING and POST_ROUTING')
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Pablo Neira Ayuso says:
====================
Netfilter updates for net-next
The following patchset contains Netfilter updates for net-next.
Basically, more incremental updates for br_netfilter from Florian
Westphal, small nf_tables updates (including one fix for rb-tree
locking) and small two-liner to add extra validation for the REJECT6
target.
More specifically, they are:
1) Use the conntrack status flags from br_netfilter to know that DNAT is
happening. Patch for Florian Westphal.
2) nf_bridge->physoutdev == NULL already indicates that the traffic is
bridged, so let's get rid of the BRNF_BRIDGED flag. Also from Florian.
3) Another patch to prepare voidization of seq_printf/seq_puts/seq_putc,
from Joe Perches.
4) Consolidation of nf_tables_newtable() error path.
5) Kill nf_bridge_pad used by br_netfilter from ip_fragment(),
from Florian Westphal.
6) Access rb-tree root node inside the lock and remove unnecessary
locking from the get path (we already hold nfnl_lock there), from
Patrick McHardy.
7) You cannot use a NFT_SET_ELEM_INTERVAL_END when the set doesn't
support interval, also from Patrick.
8) Enforce IP6T_F_PROTO from ip6t_REJECT to make sure the core is
actually restricting matches to TCP.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The br_netfilter frag output function calls skb_cow_head() so in
case it needs a larger headroom to e.g. re-add a previously stripped PPPOE
or VLAN header things will still work (at cost of reallocation).
We can then move nf_bridge_encap_header_len to br_netfilter.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Conflicts:
drivers/net/ethernet/emulex/benet/be_main.c
net/core/sysctl_net_core.c
net/ipv4/inet_diag.c
The be_main.c conflict resolution was really tricky. The conflict
hunks generated by GIT were very unhelpful, to say the least. It
split functions in half and moved them around, when the real actual
conflict only existed solely inside of one function, that being
be_map_pci_bars().
So instead, to resolve this, I checked out be_main.c from the top
of net-next, then I applied the be_main.c changes from 'net' since
the last time I merged. And this worked beautifully.
The inet_diag.c and sysctl_net_core.c conflicts were simple
overlapping changes, and were easily to resolve.
Signed-off-by: David S. Miller <davem@davemloft.net>
Its not needed anymore since 2bf540b73e
([NETFILTER]: bridge-netfilter: remove deferred hooks).
Before this it was possible to have physoutdev set for locally generated
packets -- this isn't the case anymore:
BRNF_STATE_BRIDGED flag is set when we assign nf_bridge->physoutdev,
so physoutdev != NULL means BRNF_STATE_BRIDGED is set.
If physoutdev is NULL, then we are looking at locally-delivered and
routed packet.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
ask conntrack instead of storing ipv4 address in nf_bridge_info->data.
Ths avoids the need to use ->data during NF_PRE_ROUTING.
Only two functions that need ->data remain.
These will be addressed in followup patches.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
On adding an interface br_add_if() sets the MTU to the min of
all the interfaces. Do the same thing on removing an interface too
in br_del_if.
Signed-off-by: Venkat Venkatsubra <venkat.x.venkatsubra@oracle.com>
Acked-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
e5de75b ("netfilter: bridge: move DNAT helper to br_netfilter") results
in the following link problem:
net/bridge/br_device.c:29: undefined reference to `br_nf_prerouting_finish_bridge`
Moreover it creates a hard dependency between br_netfilter and the
bridge core, which is what we've been trying to avoid so far.
Resolve this problem by using a hook structure so we reduce #ifdef
pollution and keep bridge netfilter specific code under br_netfilter.c
which was the original intention.
Reported-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
make C=1 CF=-D__CHECK_ENDIAN__ shows following:
net/bridge/netfilter/nft_reject_bridge.c:65:50: warning: incorrect type in argument 3 (different base types)
net/bridge/netfilter/nft_reject_bridge.c:65:50: expected restricted __be16 [usertype] protocol [..]
net/bridge/netfilter/nft_reject_bridge.c:102:37: warning: cast from restricted __be16
net/bridge/netfilter/nft_reject_bridge.c:102:37: warning: incorrect type in argument 1 (different base types) [..]
net/bridge/netfilter/nft_reject_bridge.c:121:50: warning: incorrect type in argument 3 (different base types) [..]
net/bridge/netfilter/nft_reject_bridge.c:168:52: warning: incorrect type in argument 3 (different base types) [..]
net/bridge/netfilter/nft_reject_bridge.c:233:52: warning: incorrect type in argument 3 (different base types) [..]
Caused by two (harmless) errors:
1. htons() instead of ntohs()
2. __be16 for protocol in nf_reject_ipXhdr_put API, use u8 instead.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
After my change to neigh_hh_init to obtain the protocol from the
neigh_table there are no more users of protocol in struct dst_ops.
Remove the protocol field from dst_ops and all of it's initializers.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pablo Neira Ayuso says:
====================
Netfilter updates for net-next
The following patchset contains Netfilter updates for your net-next
tree. Basically, improvements for the packet rejection infrastructure,
deprecation of CLUSTERIP, cleanups for nf_tables and some untangling for
br_netfilter. More specifically they are:
1) Send packet to reset flow if checksum is valid, from Florian Westphal.
2) Fix nf_tables reject bridge from the input chain, also from Florian.
3) Deprecate the CLUSTERIP target, the cluster match supersedes it in
functionality and it's known to have problems.
4) A couple of cleanups for nf_tables rule tracing infrastructure, from
Patrick McHardy.
5) Another cleanup to place transaction declarations at the bottom of
nf_tables.h, also from Patrick.
6) Consolidate Kconfig dependencies wrt. NF_TABLES.
7) Limit table names to 32 bytes in nf_tables.
8) mac header copying in bridge netfilter is already required when
calling ip_fragment(), from Florian Westphal.
9) move nf_bridge_update_protocol() to br_netfilter.c, also from
Florian.
10) Small refactor in br_netfilter in the transmission path, again from
Florian.
11) Move br_nf_pre_routing_finish_bridge_slow() to br_netfilter.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Only one caller, there is no need to keep this in a header.
Move it to br_netfilter.c where this belongs to.
Based on patch from Florian Westphal.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
The mac header only has to be copied back into the skb for
fragments generated by ip_fragment(), which only happens
for bridge forwarded packets with nf-call-iptables=1 && active nf_defrag.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
This extends the design in commit 958501163d ("bridge: Add support for
IEEE 802.11 Proxy ARP") with optional set of rules that are needed to
meet the IEEE 802.11 and Hotspot 2.0 requirements for ProxyARP. The
previously added BR_PROXYARP behavior is left as-is and a new
BR_PROXYARP_WIFI alternative is added so that this behavior can be
configured from user space when required.
In addition, this enables proxyarp functionality for unicast ARP
requests for both BR_PROXYARP and BR_PROXYARP_WIFI since it is possible
to use unicast as well as broadcast for these frames.
The key differences in functionality:
BR_PROXYARP:
- uses the flag on the bridge port on which the request frame was
received to determine whether to reply
- block bridge port flooding completely on ports that enable proxy ARP
BR_PROXYARP_WIFI:
- uses the flag on the bridge port to which the target device of the
request belongs
- block bridge port flooding selectively based on whether the proxyarp
functionality replied
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the STP timer fires, it can call br_ifinfo_notify(),
which in turn ends up in the new br_get_link_af_size().
This function is annotated to be using RTNL locking, which
clearly isn't the case here, and thus lockdep warns:
===============================
[ INFO: suspicious RCU usage. ]
3.19.0+ #569 Not tainted
-------------------------------
net/bridge/br_private.h:204 suspicious rcu_dereference_protected() usage!
Fix this by doing RCU locking here.
Fixes: b7853d73e3 ("bridge: add vlan info to bridge setlink and dellink notification messages")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Acked-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ethernet/rocker/rocker.c
The rocker commit was two overlapping changes, one to rename
the ->vport member to ->pport, and another making the bitmask
expression use '1ULL' instead of plain '1'.
Signed-off-by: David S. Miller <davem@davemloft.net>
make build fail if structure no longer fits into ->cb storage.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
bridge reject handling is not straightforward, there are many subtle
differences depending on configuration.
skb->dev is either the bridge port (PRE_ROUTING) or the bridge
itself (INPUT), so we need to use indev instead.
Also, checksum validation will only work reliably if we trim skb
according to the l3 header size.
While at it, add csum validation for ipv6 and skip existing tests
if skb was already checked e.g. by GRO.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
my previous patch skipped vlan range optimizations during skb size
calculations for simplicity.
This incremental patch considers vlan ranges during
skb size calculations. This leads to a bit of code duplication
in the fill and size calculation functions. But, I could not find a
prettier way to do this. will take any suggestions.
Previously, I had reused the existing br_get_link_af_size size calculation
function to calculate skb size for notifications. Reusing it this time
around creates some change in behaviour issues for the usual
.get_link_af_size callback.
This patch adds a new br_get_link_af_size_filtered() function to
base the size calculation on the incoming filter flag and include
vlan ranges.
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Reviewed-by: Scott Feldman <sfeldma@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
vlan add/deletes are not notified to userspace today. This patch adds
vlan info to bridge newlink/dellink notifications generated from the
bridge driver. Notifications use the RTEXT_FILTER_BRVLAN_COMPRESSED
flag to compress vlans into ranges whereever applicable.
The size calculations does not take ranges into account for
simplicity. This has the potential for allocating a larger skb than
required.
There is an existing inconsistency with bridge NEWLINK and DELLINK
change notifications. Both generate NEWLINK notifications. Since its
always a NEWLINK notification, this patch includes all vlans the port
belongs to in the notification. The NEWLINK and DELLINK request
messages however only include the vlans to be added and deleted.
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If CONFIG_SYSCTL=n:
net/bridge/br_netfilter.c: In function ‘br_netfilter_init’:
net/bridge/br_netfilter.c:996: warning: label ‘err1’ defined but not used
Move the label and the code after it inside the existing #ifdef to get
rid of the warning.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Bridge's default_pvid adds a vid by default, by which we cannot add a
non-vlan fdb entry by default, because br_fdb_add() adds fdb entries for
all vlans instead of a non-vlan one when any vlan is configured.
# ip link add br0 type bridge
# ip link set eth0 master br0
# bridge fdb add 12:34:56:78:90:ab dev eth0 master temp
# bridge fdb show brport eth0 | grep 12:34:56:78:90:ab
12:34:56:78:90:ab dev eth0 vlan 1 static
We expect a non-vlan fdb entry as well as vlan 1:
12:34:56:78:90:ab dev eth0 static
To fix this, we need to insert a non-vlan fdb entry if vlan is not
specified, even when any vlan is configured.
Fixes: 5be5a2df40 ("bridge: Add filtering support for default_pvid")
Signed-off-by: Toshiaki Makita <makita.toshiaki@lab.ntt.co.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes a missing bridge port check caught by smatch.
setlink/dellink of attributes like vlans can come for a bridge device
and there is no need to offload those today. So, this patch adds a bridge
port check. (In these cases however, the BRIDGE_SELF flags will always be set
and we may not hit a problem with the current code).
smatch complaint:
The patch 68e331c785b8: "bridge: offload bridge port attributes to
switch asic if feature flag set" from Jan 29, 2015, leads to the
following Smatch complaint:
net/bridge/br_netlink.c:552 br_setlink()
error: we previously assumed 'p' could be null (see line 518)
net/bridge/br_netlink.c
517
518 if (p && protinfo) {
^
Check for NULL.
Reported-By: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/vxlan.c
drivers/vhost/net.c
include/linux/if_vlan.h
net/core/dev.c
The net/core/dev.c conflict was the overlap of one commit marking an
existing function static whilst another was adding a new function.
In the include/linux/if_vlan.h case, the type used for a local
variable was changed in 'net', whereas the function got rewritten
to fix a stacked vlan bug in 'net-next'.
In drivers/vhost/net.c, Al Viro's iov_iter conversions in 'net-next'
overlapped with an endainness fix for VHOST 1.0 in 'net'.
In drivers/net/vxlan.c, vxlan_find_vni() added a 'flags' parameter
in 'net-next' whereas in 'net' there was a bug fix to pass in the
correct network namespace pointer in calls to this function.
Signed-off-by: David S. Miller <davem@davemloft.net>
When 'learned_sync' flag is turned on, the offloaded switch
port syncs learned MAC addresses to bridge's FDB via switchdev notifier
(NETDEV_SWITCH_FDB_ADD). Currently, FDB entries learnt via this mechanism are
wrongly being deleted by bridge aging logic. This patch ensures that FDB
entries synced from offloaded switch ports are not deleted by bridging logic.
Such entries can only be deleted via switchdev notifier
(NETDEV_SWITCH_FDB_DEL).
Signed-off-by: Siva Mannem <siva.mannem.lnx@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Nicolas Dichtel
Patrick McHardy
David S. Miller
Pablo Neira Ayuso
Florian Westphal
Jörg Thalheim
Venkat Venkatsubra
Eric W. Biederman
Jouni Malinen
Johannes Berg
Roopa Prabhu
Geert Uytterhoeven
Toshiaki Makita
Siva Mannem