Patch converts driver to using resource-managed functions.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This remedies a few problems:
(1) The use of "the" vs. "a" is a little confusing, IMO.
(2) nand_chip.block_bad is used exclusively for checking the OOB bad
block markers of a NAND. Any BBT functionality is handled in
nand_bbt.c, so this description should differentiate itself from
nand_bbt.c.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Traditionally, the command set used by SPI flash only supported a 3-byte
address. However, large SPI flash (>= 32MiB, or 256Mib) require 4 bytes
to address the entire flash. Most manufacturers have supplied a mode
switch (via a "bank register writer", or a "enable 4-byte mode"
command), which tells the flash to expect 4 address cycles from now on,
instead of 3. This mode remains until power is cut, the reset line is
triggered (on packages where present), or a command is sent to reset the
flash or to reset the 3-byte addressing mode.
As an alternative, some flash manufacturers have developed a new command
set that accept a full 4-byte address. They can be used orthogonally to
any of the modes; that is, they can be used when the flash is in either
3-byte or 4-byte address mode.
Now, there are a number of reasons why the "stateful" 4-byte address
mode switch may not be acceptable. For instance, some SoC's perform a
dumb boot sequence in which they only send 3-byte read commands to the
flash. However, if an unexpected reset occurs, the flash chip cannot be
guaranteed to return to its 3-byte mode. Thus, the SoC controller and
flash will not understand each other. (One might consider hooking up the
aforementioned reset pin to the system reset line so that any system
reset will reset the flash to 3-byte mode, but some packages do not
provide this pin. And in some other packages, one must choose between
having a reset pin and having enough pins for 4-output QSPI support.
It is an error prone process choosing a flash that will support a
hardware reset pin!)
This patch provides support for the new stateless command set, so that
we can avoid the problems that come with a stateful addressing mode
change. The flash can be left in "3-byte mode" while still accessing the
entire flash.
Note that Spansion supports this command set on all its large flash
(e.g, S25FL512S), and Macronix has begun supporting this command set on
some new flash (e.g., MX25L25635F). For the moment, I don't know how to
differentiate the Macronix that don't support this command set (e.g.,
MX25L25635E) from those that do, so this patch only supports Spansion.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Acked-by: Marek Vasut <marex@denx.de>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This controller only does ECC on full-page accesses, even though the
ECC consists of multiple steps. fsl_elbc_nand can get away with this
because the ECC of an all-0xff region will be all-0xff, but this is not
true with the ECC algorithms used by IFC.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Convert all users of devm_request_and_ioremap() to the newly introduced
devm_ioremap_resource() which provides more consistent error handling.
Signed-off-by: Silviu-Mihai Popescu <silviupopescu1990@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Use the wrapper functions for getting and setting the driver data using
spi_device instead of using dev_{get|set}_drvdata with &spi->dev, so we
can directly pass a struct spi_device.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Use the wrapper functions for getting and setting the driver data using
spi_device instead of using dev_{get|set}_drvdata with &spi->dev, so we
can directly pass a struct spi_device.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Use the wrapper functions for getting and setting the driver data using
spi_device instead of using dev_{get|set}_drvdata with &spi->dev, so we
can directly pass a struct spi_device.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Print out the @adr when the write timeout occurs.
This is useful to check if the write timeouts occur at the
same address.
Signed-off-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Add CONFIG_PM_SLEEP to suspend/resume functions to fix the following
build warning when CONFIG_PM_SLEEP is not selected. This is because
sleep PM callbacks defined by SIMPLE_DEV_PM_OPS are only used when
the CONFIG_PM_SLEEP is enabled. Also, unnecessary CONFIG_PM ifdefs
are removed
drivers/mtd/devices/spear_smi.c:1049:12: warning: 'spear_smi_suspend' defined but not used [-Wunused-function]
drivers/mtd/devices/spear_smi.c:1059:12: warning: 'spear_smi_resume' defined but not used [-Wunused-function]
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Add CONFIG_PM_SLEEP to suspend/resume functions to fix the following
build warning when CONFIG_PM_SLEEP is not selected. This is because
sleep PM callbacks defined by SIMPLE_DEV_PM_OPS are only used when
the CONFIG_PM_SLEEP is enabled. Also, unnecessary CONFIG_PM ifdefs
are removed.
drivers/mtd/nand/fsmc_nand.c:1194:12: warning: 'fsmc_nand_suspend' defined but not used [-Wunused-function]
drivers/mtd/nand/fsmc_nand.c:1202:12: warning: 'fsmc_nand_resume' defined but not used [-Wunused-function]
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Add CONFIG_PM_SLEEP to suspend/resume functions to fix the following
build warning when CONFIG_PM_SLEEP is not selected. This is because
sleep PM callbacks defined by SIMPLE_DEV_PM_OPS are only used when
the CONFIG_PM_SLEEP is enabled. Also, unnecessary NULL defines are
removed.
drivers/mtd/nand/r852.c:1006:12: warning: 'r852_suspend' defined but not used [-Wunused-function]
drivers/mtd/nand/r852.c:1027:12: warning: 'r852_resume' defined but not used [-Wunused-function]
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Read out the SPI size from nvram instead of defaulting to 64KiB — some
vendors actually use values larger than the "max" value of 64.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
Acked-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The struct fsl_ifc_mtd is allocated with devm_kzalloc, so its memory
is "managed" automatically by the kernel. That is, we do not need to
free it explicitly; it will be freed when the device is removed. And we
*certainly* shouldn't free it with a regular kfree().
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
They are needed for erasing/writing. Use a magic pointers and small
functions to prepare code for adding other buses support in the future
(like SSB).
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Pull dmaengine fixes from Vinod Koul:
"Two fixes for slave dmaengine. The first fixes cyclic dma transfers
for pl330 and the second one makes us return the correct error code on
probe"
* 'fixes' of git://git.infradead.org/users/vkoul/slave-dma:
dma: pl330: Fix cyclic transfers
pch_dma: fix error return code in pch_dma_probe()
Pull drm fix from Dave Airlie:
"Just a quick fix that a few people have reported, be nice to have in
asap"
The drm tree seems to be very confused about 64-bit divides. Here it
uses a slow 64-by-64 bit divide to divide by a small constant. Oh well.
Doesn't look performance-critical, just stupid.
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
drm/radeon: fix 64 bit divide in SI spm code
Commit 46a1c2c7ae ("vfs: export lseek_execute() to modules") broke the
tmpfs SEEK_DATA/SEEK_HOLE implementation, because vfs_setpos() converts
the carefully prepared -ENXIO to -EINVAL. Other filesystems avoid it in
error cases: do the same in tmpfs.
Signed-off-by: Hugh Dickins <hughd@google.com>
Cc: Jie Liu <jeff.liu@oracle.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
All small regression or small fixes, nothing surprising at this stage.
- regression fix for Mac MINI quirk
- compress ioctl error fix
- ASoC fixes for control change notifications, some UI fixes,
driver-specific fixes (resource leak, build errors, etc)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)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=buMS
-----END PGP SIGNATURE-----
Merge tag 'sound-3.11' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"All small regression or small fixes, nothing surprising at this stage.
- regression fix for intel Mac Mini quirk
- compress ioctl error fix
- ASoC fixes for control change notifications, some UI fixes,
driver-specific fixes (resource leak, build errors, etc)"
* tag 'sound-3.11' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: hda - Fix missing fixup for Mac Mini with STAC9221
ASoC: wm0010: Fix resource leak
ASoC: au1x: Fix build
ASoC: bf5xx-ac97: Fix compile error with SND_BF5XX_HAVE_COLD_RESET
ASoC: bfin-ac97: Fix prototype error following AC'97 refactoring
ALSA: compress: fix the return value for SNDRV_COMPRESS_VERSION
ASoC: dapm: Fix return value of snd_soc_dapm_put_{volsw,enum_virt}()
Pull networking fixes from David Miller:
1) Don't ignore user initiated wireless regulatory settings on cards
with custom regulatory domains, from Arik Nemtsov.
2) Fix length check of bluetooth information responses, from Jaganath
Kanakkassery.
3) Fix misuse of PTR_ERR in btusb, from Adam Lee.
4) Handle rfkill properly while iwlwifi devices are offline, from
Emmanuel Grumbach.
5) Fix r815x devices DMA'ing to stack buffers, from Hayes Wang.
6) Kernel info leak in ATM packet scheduler, from Dan Carpenter.
7) 8139cp doesn't check for DMA mapping errors, from Neil Horman.
8) Fix bridge multicast code to not snoop when no querier exists,
otherwise mutlicast traffic is lost. From Linus Lüssing.
9) Avoid soft lockups in fib6_run_gc(), from Michal Kubecek.
10) Fix races in automatic address asignment on ipv6, which can result
in incorrect lifetime assignments. From Jiri Benc.
11) Cure build bustage when CONFIG_NET_LL_RX_POLL is not set and rename
it CONFIG_NET_RX_BUSY_POLL to eliminate the last reference to the
original naming of this feature. From Cong Wang.
12) Fix crash in TIPC when server socket creation fails, from Ying Xue.
13) macvlan_changelink() silently succeeds when it shouldn't, from
Michael S Tsirkin.
14) HTB packet scheduler can crash due to sign extension, fix from
Stephen Hemminger.
15) With the cable unplugged, r8169 prints out a message every 10
seconds, make it netif_dbg() instead of netif_warn(). From Peter
Wu.
16) Fix memory leak in rtm_to_ifaddr(), from Daniel Borkmann.
17) sis900 gets spurious TX queue timeouts due to mismanagement of link
carrier state, from Denis Kirjanov.
18) Validate somaxconn sysctl to make sure it fits inside of a u16.
From Roman Gushchin.
19) Fix MAC address filtering on qlcnic, from Shahed Shaikh.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (68 commits)
qlcnic: Fix for flash update failure on 83xx adapter
qlcnic: Fix link speed and duplex display for 83xx adapter
qlcnic: Fix link speed display for 82xx adapter
qlcnic: Fix external loopback test.
qlcnic: Removed adapter series name from warning messages.
qlcnic: Free up memory in error path.
qlcnic: Fix ingress MAC learning
qlcnic: Fix MAC address filter issue on 82xx adapter
net: ethernet: davinci_emac: drop IRQF_DISABLED
netlabel: use domain based selectors when address based selectors are not available
net: check net.core.somaxconn sysctl values
sis900: Fix the tx queue timeout issue
net: rtm_to_ifaddr: free ifa if ifa_cacheinfo processing fails
r8169: remove "PHY reset until link up" log spam
net: ethernet: cpsw: drop IRQF_DISABLED
htb: fix sign extension bug
macvlan: handle set_promiscuity failures
macvlan: better mode validation
tipc: fix oops when creating server socket fails
net: rename CONFIG_NET_LL_RX_POLL to CONFIG_NET_RX_BUSY_POLL
...
Flash update routine was improperly checking register read API return value.
Modify register read API and perform proper error check.
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o Set link speed and duplex to unknown when link is not up.
Signed-off-by: Rajesh Borundia <rajesh.borundia@qlogic.com>
Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o Do not obtain link speed from register when adapter
link is down.
Signed-off-by: Rajesh Borundia <rajesh.borundia@qlogic.com>
Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Driver was not handling external loopback diagnostic
test request.
Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Pratik Pujar <pratik.pujar@qlogic.com>
Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o Delete MAC address from the adapter's filter table
if the source MAC address of ingress packet matches.
Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Driver was passing the address of a pointer instead of
the pointer itself.
Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
IRQF_DISABLED is a no-op by now and should be removed.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull nfsd bugfixes from Bruce Fields:
"Most of this is due to a screwup on my part -- some gss-proxy crashes
got fixed before the merge window but somehow never made it out of a
temporary git repo on my laptop...."
* 'for-3.11' of git://linux-nfs.org/~bfields/linux:
svcrpc: set cr_gss_mech from gss-proxy as well as legacy upcall
svcrpc: fix kfree oops in gss-proxy code
svcrpc: fix gss-proxy xdr decoding oops
svcrpc: fix gss_rpc_upcall create error
NFSD/sunrpc: avoid deadlock on TCP connection due to memory pressure.
Pull arm fixes fixes from Russell King:
"This fixes a couple of problems with commit 48be69a026 ("ARM: move
signal handlers into a vdso-like page"), one of which was originally
discovered via my testing originally, but the fix for it was never
actually committed.
The other shows up on noMMU builds, and such platforms are extremely
rare and as such are not part of my nightly testing"
* 'fixes' of git://git.linaro.org/people/rmk/linux-arm:
ARM: fix nommu builds with 48be69a02 (ARM: move signal handlers into a vdso-like page)
ARM: fix a cockup in 48be69a02 (ARM: move signal handlers into a vdso-like page)
Without this patch, the values for ideality (register 0x4b) and ideality
selection mask (register 0x4c) are inverted.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Cc: stable@vger.kernel.org # 3.9+
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Olof reports that noMMU builds error out with:
arch/arm/kernel/signal.c: In function 'setup_return':
arch/arm/kernel/signal.c:413:25: error: 'mm_context_t' has no member named 'sigpage'
This shows one of the evilnesses of IS_ENABLED(). Get rid of it here
and replace it with #ifdef's - and as no noMMU platform can make use
of sigpage, depend on CONIFG_MMU not CONFIG_ARM_MPU.
Reported-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Unfortunately, I never committed the fix to a nasty oops which can
occur as a result of that commit:
------------[ cut here ]------------
kernel BUG at /home/olof/work/batch/include/linux/mm.h:414!
Internal error: Oops - BUG: 0 [#1] PREEMPT SMP ARM
Modules linked in:
CPU: 0 PID: 490 Comm: killall5 Not tainted 3.11.0-rc3-00288-gabe0308 #53
task: e90acac0 ti: e9be8000 task.ti: e9be8000
PC is at special_mapping_fault+0xa4/0xc4
LR is at __do_fault+0x68/0x48c
This doesn't show up unless you do quite a bit of testing; a simple
boot test does not do this, so all my nightly tests were passing fine.
The reason for this is that install_special_mapping() expects the
page array to stick around, and as this was only inserting one page
which was stored on the kernel stack, that's why this was blowing up.
Reported-by: Olof Johansson <olof@lixom.net>
Tested-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
NetLabel has the ability to selectively assign network security labels
to outbound traffic based on either the LSM's "domain" (different for
each LSM), the network destination, or a combination of both. Depending
on the type of traffic, local or forwarded, and the type of traffic
selector, domain or address based, different hooks are used to label the
traffic; the goal being minimal overhead.
Unfortunately, there is a bug such that a system using NetLabel domain
based traffic selectors does not correctly label outbound local traffic
that is not assigned to a socket. The issue is that in these cases
the associated NetLabel hook only looks at the address based selectors
and not the domain based selectors. This patch corrects this by
checking both the domain and address based selectors so that the correct
labeling is applied, regardless of the configuration type.
In order to acomplish this fix, this patch also simplifies some of the
NetLabel domainhash structures to use a more common outbound traffic
mapping type: struct netlbl_dommap_def. This simplifies some of the code
in this patch and paves the way for further simplifications in the
future.
Signed-off-by: Paul Moore <pmoore@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It's possible to assign an invalid value to the net.core.somaxconn
sysctl variable, because there is no checks at all.
The sk_max_ack_backlog field of the sock structure is defined as
unsigned short. Therefore, the backlog argument in inet_listen()
shouldn't exceed USHRT_MAX. The backlog argument in the listen() syscall
is truncated to the somaxconn value. So, the somaxconn value shouldn't
exceed 65535 (USHRT_MAX).
Also, negative values of somaxconn are meaningless.
before:
$ sysctl -w net.core.somaxconn=256
net.core.somaxconn = 256
$ sysctl -w net.core.somaxconn=65536
net.core.somaxconn = 65536
$ sysctl -w net.core.somaxconn=-100
net.core.somaxconn = -100
after:
$ sysctl -w net.core.somaxconn=256
net.core.somaxconn = 256
$ sysctl -w net.core.somaxconn=65536
error: "Invalid argument" setting key "net.core.somaxconn"
$ sysctl -w net.core.somaxconn=-100
error: "Invalid argument" setting key "net.core.somaxconn"
Based on a prior patch from Changli Gao.
Signed-off-by: Roman Gushchin <klamm@yandex-team.ru>
Reported-by: Changli Gao <xiaosuo@gmail.com>
Suggested-by: Eric Dumazet <edumazet@google.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- Fixes for the newly merged mlx5 hardware driver
- Stack info leak fixes from Dan Carpenter
- Fixes for pkey table handling with SR-IOV
- A few other small things
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=ZwEX
-----END PGP SIGNATURE-----
Merge tag 'rdma-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband
Pull infiniband/rdma fixes from Roland Dreier:
- Fixes for the newly merged mlx5 hardware driver
- Stack info leak fixes from Dan Carpenter
- Fixes for pkey table handling with SR-IOV
- A few other small things
* tag 'rdma-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband:
IPoIB: Fix pkey change flow for virtualization environments
IPoIB: Make sure child devices use valid/proper pkeys
IB/core: Create QP1 using the pkey index which contains the default pkey
mlx5_core: Variable may be used uninitialized
mlx5_core: Implement new initialization sequence
mlx5_core: Fix use after free in mlx5_cmd_comp_handler()
IB/mlx5: Fix stack info leak in mlx5_ib_alloc_ucontext()
IB/mlx5: Fix error return code in init_one()
IB/mlx4: Use default pkey when creating tunnel QPs
RDMA/cma: Only call cma_save_ib_info() for CM REQs
RDMA/cma: Fix accessing invalid private data for UD
RDMA/cma: Fix gcc warning
Revert "RDMA/nes: Fix compilation error when nes_debug is enabled"
IB/qib: Add err_decode() call for ring dump
RDMA/cxgb3: Fix stack info leak in iwch_create_cq()
RDMA/nes: Fix info leaks in nes_create_qp() and nes_create_cq()
RDMA/ocrdma: Fix several stack info leaks
RDMA/cxgb4: Fix stack info leak in c4iw_create_qp()
RDMA/ocrdma: Remove unused include
- Revert the OMAP fixes that caused more problems than they solved.
- Fix a build error.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.13 (GNU/Linux)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=PQ04
-----END PGP SIGNATURE-----
Merge tag 'gpio-for-v3.11-3' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO fixes from Linus Walleij:
"Yet another GPIO pull request, fixing the fix from the last one. It
turns out that fixing the boot path for device tree boots on OMAP
breaks out antique systems (such as OMAP1) and we need to find a
better way. So we're reverting that "fix" for the moment and thinking
about something better.
Also fixing a build issue on the MSM driver"
* tag 'gpio-for-v3.11-3' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio:
gpio_msm: Fix build error due to missing err.h
Revert "gpio/omap: don't create an IRQ mapping for every GPIO on DT"
Revert "gpio/omap: auto request GPIO as input if used as IRQ via DT"
Revert "gpio/omap: fix build error when OF_GPIO is not defined."
Alexander Shiyan
Brian Norris
Scott Wood
Silviu-Mihai Popescu
Jingoo Han
Huang Shijie
Jonas Gorski
Rafał Miłecki
Linus Torvalds
Hugh Dickins
Alex Deucher
Himanshu Madhani
Rajesh Borundia
Shahed Shaikh
Pratik Pujar
Mugunthan V N
Vivien Didelot
Russell King
Paul Moore
Roman Gushchin
Denis Kirjanov