Граф коммитов

367 Коммитов

Автор SHA1 Сообщение Дата
Jaehoon Chung 950d56acce mmc: support BKOPS feature for eMMC
Enable eMMC background operations (BKOPS) feature.

If URGENT_BKOPS is set after a response, note that BKOPS are required.
Immediately run BKOPS if required.  Read/write operations should be
requested during BKOPS(LEVEL-1), then issue HPI to interrupt the
ongoing BKOPS and service the foreground operation.
(This patch only controls the LEVEL2/3.)

When repeating the writing 1GB data, at a certain time, performance is
decreased.  At that time, card triggers the Level-3 or Level-2.  After
running bkops, performance is recovered.

Future considerations:
 * Check BKOPS_LEVEL=1 and start BKOPS in a preventive manner.
 * Interrupt ongoing BKOPS before powering off the card.
 * How do we get BKOPS_STATUS value (periodically send ext_csd command)?
 * If using periodic bkops, also consider runtime_pm control.

Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Konstantin Dorfman <kdorfman@codeaurora.org>
Reviewed-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
2012-10-03 10:05:12 -04:00
Johan Rudholm 3339d1e331 mmc: core: Do not rescan non-removable devices
If MMC_CAP_NONREMOVABLE is set, only issue a detect job on init.

Signed-off-by: Johan Rudholm <johan.rudholm@stericsson.com>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
2012-09-04 13:58:27 -04:00
Philip Rakity 6231f3de13 mmc: sdhci: Add regulator support for vccq (voltage regualor)
On some systems the host controller does not support vccq
signaling.  This is supplied by a dedicated regulator (vqmmc).
Add support for this regulator.

Signed-off-by: Philip Rakity <prakity@marvell.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
2012-09-04 13:58:13 -04:00
Ian Chen 3550ccdb9d mmc: card: Skip secure erase on MoviNAND; causes unrecoverable corruption.
For several MoviNAND eMMC parts, there are known issues with secure
erase and secure trim.  For these specific MoviNAND devices, we skip
these operations.

Specifically, there is a bug in the eMMC firmware that causes
unrecoverable corruption when the MMC is erased with MMC_CAP_ERASE
enabled.

References:

http://forum.xda-developers.com/showthread.php?t=1644364
https://plus.google.com/111398485184813224730/posts/21pTYfTsCkB#111398485184813224730/posts/21pTYfTsCkB

Signed-off-by: Ian Chen <ian.cy.chen@samsung.com>
Reviewed-by: Namjae Jeon <linkinjeon@gmail.com>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Cc: stable <stable@vger.kernel.org> [3.0+]
Signed-off-by: Chris Ball <cjb@laptop.org>
2012-09-04 13:58:10 -04:00
Linus Torvalds c511dc1fb6 Merge branch 'next' of git://git.infradead.org/users/vkoul/slave-dma
Pull slave-dmaengine update from Vinod Koul:
 "This time we have a new dmaengine driver from the tegra folks.  Also
  we have Guennadi's cleanup of sh drivers which incudes a library for
  sh drivers.  And the usual odd fixes in bunch of drivers and some nice
  cleanup of dw_dmac from Andy."

Fix up conflicts in drivers/mmc/host/sh_mmcif.c

* 'next' of git://git.infradead.org/users/vkoul/slave-dma: (46 commits)
  dmaengine: Cleanup logging messages
  mmc: sh_mmcif: switch to the new DMA channel allocation and configuration
  dma: sh: provide a migration path for slave drivers to stop using .private
  dma: sh: use an integer slave ID to improve API compatibility
  dmaengine: shdma: prepare to stop using struct dma_chan::private
  sh: remove unused DMA device pointer from SIU platform data
  ASoC: siu: don't use DMA device for channel filtering
  dmaengine: shdma: (cosmetic) simplify a static function
  dmaengine: at_hdmac: add a few const qualifiers
  dw_dmac: use 'u32' for LLI structure members, not dma_addr_t
  dw_dmac: mark dwc_dump_lli inline
  dma: mxs-dma: Export missing symbols from mxs-dma.c
  dma: shdma: convert to the shdma base library
  ASoC: fsi: prepare for conversion to the shdma base library
  usb: renesas_usbhs: prepare for conversion to the shdma base library
  ASoC: siu: prepare for conversion to the shdma base library
  serial: sh-sci: prepare for conversion to the shdma base library
  mmc: sh_mobile_sdhi: prepare for conversion to the shdma base library
  mmc: sh_mmcif: remove unneeded struct sh_mmcif_dma, prepare to shdma conversion
  dma: shdma: prepare for conversion to the shdma base library
  ...
2012-07-24 17:12:54 -07:00
Aaron Lu 55c4665ea0 mmc: sd: Fix sd current limit setting
Host has different current capabilities at different voltages, we need
to record these settings seperately. The defined voltages are 1.8/3.0/3.3.
For other voltages, we do not touch current limit setting.

Before we set the current limit for the sd card, find out the host's
operating voltage first and then find out the current capabilities of
the host at that voltage to set the current limit.

Signed-off-by: Aaron Lu <aaron.lu@amd.com>
Reviewed-by: Philip Rakity <prakity@marvell.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
2012-07-22 15:25:52 -04:00
Aaron Lu 973905feab mmc: sdhci: Introduce new flag SDHCI_USING_RETUNING_TIMER
Add a new flag of SDHCI_USING_RETUNING_TIMER to represent if the host
is using a retuning timer for the card inserted.

This flag is set when the host does tuning the first time for the card
and the host's retuning mode is 1. This flag is used afterwards whenever
needs to decide if the host is currently using a retuning timer.

This flag is cleared when the card is removed in sdhci_reinit.

The set/clear of the flag and the start/stop of the retuning timer is
associated with the card's init/remove time, so there is no need to
touch it when the host is to be removed as at that time the card should
have already been removed.

Signed-off-by: Aaron Lu <aaron.lu@amd.com>
Reviewed-by: Girish K S <girish.shivananjappa@linaro.org>
Reviewed-by: Philip Rakity <prakity@marvell.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
2012-07-22 15:25:49 -04:00
Philip Rakity bd6a8c30fa mmc: sdhci: Allow caps[1] to be set via SDHCI_QUIRK_MISSING_CAPS
Currently only the capability_0 register can be set if
SDHCI_QUIRK_MISSING_CAPS is defined.  This is a problem when
the capability_1 register also needs changing.  Use the quirk
SDHCI_QUIRK_MISSING_CAPS to allow both registers to be set.

Redefining caps[1] is useful when the board design does not
support 1.8v vccq so UHS modes are not available.  The code that
calls sdhci_add_host can then detect this condition and adjust
the caps so the UHS mode will not be attempted on UHS cards.

Signed-off-by: Philip Rakity <prakity@marvell.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
2012-07-22 15:25:44 -04:00
Philip Rakity 0aa6770000 mmc: sdhci: only set 200mA support for 1.8v if 200mA is available
max_current_caps can return 0 if not available from the sd controller.
If no regulator is present or the regulator specifies a current
less then 200ma, we no longer still set the 200mA caps bit anyway.

Signed-off-by: Philip Rakity <prakity@marvell.com>
Reviewed-by: Aaron Lu <aaron_lu@amd.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
2012-07-21 00:02:23 -04:00
Guennadi Liakhovetski e480606ad4 mmc: sh_mmcif: support generic card-detection
Extend the sh_mmcif driver to support GPIO card detection, provided by the
slot function module. The original .get_cd() platform callback is also
preserved for now.

Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
2012-07-21 00:02:22 -04:00
Guennadi Liakhovetski d7d8d500bc mmc: sh_mobile_sdhi: support caps2 flags
Let SDHI platforms specify mmc_host::caps2 flags in their platform data.

Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
2012-07-21 00:02:19 -04:00
Guennadi Liakhovetski 5aa7dad305 mmc: core: add WP pin handler to slot functions
Card Write-Protect pin is often implemented, using a GPIO, which makes
it simple to provide a generic handler for it.

Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
2012-07-21 00:02:18 -04:00
Guennadi Liakhovetski a7d1a1ebd8 mmc: core: convert slot functions to managed allocation
This prepares for the addition of further slot functions.

Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
2012-07-21 00:02:17 -04:00
Guennadi Liakhovetski befe4048d8 mmc: add CD GPIO polling support to slot functions
A simple extension of mmc slot functions add support for CD GPIO polling
for cases where the GPIO cannot produce interrupts, or where this is not
desired for some reason.

Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
2012-07-21 00:02:17 -04:00
Guennadi Liakhovetski 5c08d7fae0 mmc: add two capability flags for CD and WP signal polarity
To handle CD and WP SD/MMC slot pins we need generic flags to specify their
polarity.

Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
2012-07-21 00:02:16 -04:00
Guennadi Liakhovetski 27410ee7e3 mmc: core: use a more generic name for slot function types and fields
struct mmc_host::hotplug is becoming a generic hook for slot functions.
Rename it accordingly.

Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
2012-07-21 00:02:16 -04:00
Guennadi Liakhovetski e137788dd1 mmc: add a function to get regulators, supplying card's power
Add a function to get regulators, supplying card's Vdd and Vccq on a
specific host. If a Vdd supplying regulator is found, the function checks,
whether a valid OCR mask can be obtained from it. The Vccq regulator is
optional. A failure to get it is not fatal.

Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Reviwed-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
2012-07-21 00:02:08 -04:00
Guennadi Liakhovetski 916001fe33 mmc: sh_mmcif: remove unneeded struct sh_mmcif_dma, prepare to shdma conversion
Now that all users have been updated to use the embedded in struct
sh_mmcif_plat_data DMA slave IDs, struct sh_mmcif_dma is no longer needed
and can be removed. This also makes preparation to the shdma base library
conversion easier.

Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Cc: Chris Ball <cjb@laptop.org>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
2012-07-13 09:13:07 +05:30
Guennadi Liakhovetski fd0ea65d3e mmc: extend and rename cd-gpio helpers to handle more slot GPIO functions
GPIOs can be used in MMC/SD-card slots not only for hotplug detection, but
also to implement the write-protection pin. Rename cd-gpio helpers to
slot-gpio to make addition of further slot GPIO functions possible.

Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
2012-07-10 23:04:04 -04:00
Linus Torvalds a2a2609c97 Merge branch 'akpm' (Andrew's patch-bomb)
* emailed from Andrew Morton <akpm@linux-foundation.org>: (21 patches)
  mm/memblock: fix overlapping allocation when doubling reserved array
  c/r: prctl: Move PR_GET_TID_ADDRESS to a proper place
  pidns: find_new_reaper() can no longer switch to init_pid_ns.child_reaper
  pidns: guarantee that the pidns init will be the last pidns process reaped
  fault-inject: avoid call to random32() if fault injection is disabled
  Viresh has moved
  get_maintainer: Fix --help warning
  mm/memory.c: fix kernel-doc warnings
  mm: fix kernel-doc warnings
  mm: correctly synchronize rss-counters at exit/exec
  mm, thp: print useful information when mmap_sem is unlocked in zap_pmd_range
  h8300: use the declarations provided by <asm/sections.h>
  h8300: fix use of extinct _sbss and _ebss
  xtensa: use the declarations provided by <asm/sections.h>
  xtensa: use "test -e" instead of bashism "test -a"
  xtensa: replace xtensa-specific _f{data,text} by _s{data,text}
  memcg: fix use_hierarchy css_is_ancestor oops regression
  mm, oom: fix and cleanup oom score calculations
  nilfs2: ensure proper cache clearing for gc-inodes
  thp: avoid atomic64_read in pmd_read_atomic for 32bit PAE
  ...
2012-06-20 14:41:57 -07:00
Viresh Kumar 10d8935f46 Viresh has moved
viresh.kumar@st.com email-id doesn't exist anymore as I have left the
company.  Replace ST's id with viresh.linux@gmail.com.

It also updates .mailmap file to fix address for 'git shortlog'

Signed-off-by: Viresh Kumar <viresh.linux@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2012-06-20 14:39:36 -07:00
Yong Ding 2a0fe914a3 mmc: sdio: fix setting card data bus width as 4-bit
SDIO_CCCR_IF[1:0] in SDIO card is used for card data bus width
setting as below:

     00b: 1-bit bus
     01b: Reserved
     10b: 4-bit bus
     11b: 8-bit bus (only for embedded SDIO)

And sdio_enable_wide is for setting data bus width as 4-bit.
But currently, it first reads the register, second OR' 1b with
SDIO_CCCR_IF[1], and then writes it back.

As we can see, this is based on such assumption that the
SDIO_CCCR_IF[0] is always 0. Apparently, this is not right.

Signed-off-by: Yong Ding <yongd@marvell.com>
Acked-by: Philip Rakity <prakity@marvell.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
2012-06-06 09:22:53 -04:00
Linus Torvalds 84a442b9a1 arm-soc: device tree conversions, part 2
These continue the device tree work from part 1, this set is for the
 tegra, mxs and imx platforms, all of which have dependencies on clock
 or pinctrl changes submitted earlier.
 -----BEGIN PGP SIGNATURE-----
 Version: GnuPG v1.4.11 (GNU/Linux)
 
 iQIcBAABAgAGBQJPuex7AAoJEIwa5zzehBx3xsQP/jkyt74MvuKUi8pi2zkeMIgn
 4XieyqcA0KZjJzfB22q3GIZjNIf/mEIGE4E/3bneVMPh/E2zaiohaXFExBmjNjml
 hhzWeZlFGPBjrZsfpIXJIIUhwSI7gX2rjYh4npJmdNhZmy8Y89XnpNJhN1kOwMuV
 oN23hPWoSVGbyDMQ0fmHx9GyOL8m7yap+joG13aljDa2OKpQg+pYvdwft+k1K9di
 8yPF+qA043UUR7dSsjmTbiCcjZy2eySdCmfOAkEG4inSgxNoM7GBs3MuwZo/veCD
 v5WssJqWDbLXtqKn5Uo2bvGWiEcf0xtwOAqhSpbaup3dQFJSWMEenBTtA9UlxFhk
 6gdY62O+7k6N0thkxXyLNGkgaGzexZAsK7dM6XSDB+PqD+OSNJS7dvmxZM8tuaRn
 rvCM1XWcNeN/dpnLbgwCR12efkwWtJoqqUZUUp/tFFaTo8HriqeAIYk7obnR8s9n
 S5x9LeueQGNgaxXJzVdh481YKG/1lqjG/a06HbVgYS4XQvtdA+4khalOefJv10tm
 Nkg8+4/8pMthWJfhhlfPUgWFXOXFF2AGPG4su2XwKuFXypO8599lzi7gUQaEZu2U
 7caqoWP69KsKvK5iAAmA4DQ2rcsgHd44NXx/8Jjes9ma8knlYjrf42dBH6AZMQBG
 69I9sJ1cyqusBwx72NPN
 =WeDQ
 -----END PGP SIGNATURE-----

Merge tag 'dt2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc

Pull arm-soc device tree conversions (part 2) from Olof Johansson:
 "These continue the device tree work from part 1, this set is for the
  tegra, mxs and imx platforms, all of which have dependencies on clock
  or pinctrl changes submitted earlier."

Fix up trivial conflicts due to nearby changes in
drivers/{gpio/gpio,i2c/busses/i2c}-mxs.c

* tag 'dt2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (73 commits)
  ARM: dt: tegra: invert status=disable vs status=okay
  ARM: dt: tegra: consistent basic property ordering
  ARM: dt: tegra: sort nodes based on bus order
  ARM: dt: tegra: remove duplicate device_type property
  ARM: dt: tegra: consistenly use lower-case for hex constants
  ARM: dt: tegra: format regs properties consistently
  ARM: dt: tegra: gpio comment cleanup
  ARM: dt: tegra: remove unnecessary unit addresses
  ARM: dt: tegra: whitespace cleanup
  ARM: dt: tegra cardhu: fix typo in SDHCI node name
  ARM: dt: tegra: cardhu: register core regulator tps62361
  ARM: dt: tegra30.dtsi: Add SMMU node
  ARM: dt: tegra20.dtsi: Add GART node
  ARM: dt: tegra30.dtsi: Add Memory Controller(MC) nodes
  ARM: dt: tegra20.dtsi: Add Memory Controller(MC) nodes
  ARM: dt: tegra: Add device tree support for AHB
  ARM: dts: enable audio support for imx28-evk
  ARM: dts: enable i2c device for imx28-evk
  i2c: mxs: add device tree probe support
  ARM: dts: enable mmc for imx28-evk
  ...
2012-05-26 12:57:47 -07:00
Shawn Guo 81f38ee8e6 mmc: mxs-mmc: move header from mach into linux folder
Rename arch/arm/mach-mxs/include/mach/mmc.h to
include/linux/mmc/mxs-mmc.h, so that mxs-mmc driver becomes
<mach/*> inclusion free.

Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Marek Vasut <marex@denx.de>
Acked-by: Chris Ball <cjb@laptop.org>
2012-05-13 08:05:38 +08:00
Thomas Abraham 95dcc2cb6c mmc: dw_mmc: make multiple instances of dw_mci_card_workqueue
The variable 'dw_mci_card_workqueue' is a global variable shared between
multiple instances of the dw_mmc host controller. Due to this, data
corruption has been noticed when multiple instances of dw_mmc controllers
are actively reading/writing the media. Fix this by adding a instance
of 'struct workqueue_struct' for each host instance and removing the
global 'dw_mci_card_workqueue' instance.

Signed-off-by: Thomas Abraham <thomas.abraham@linaro.org>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Acked-by: Will Newton <will.newton@imgtec.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
2012-05-09 10:14:10 -04:00
Seungwon Jeon 96cf5f02ae mmc: core: fix the decision of HS200/DDR card-type
Current implementation decides the card type exclusively. Even though
eMMC device can support both HS200 and DDR mode, card type will be
set only for HS200. If the host doesn't support HS200 but has DDR
capability, then DDR mode can't be selected.

Signed-off-by: Seungwon Jeon <tgih.jun@samsung.com>
Reviewed-by: Subhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
2012-05-09 10:03:21 -04:00
Nicolas Pitre bbbc4c4d8c mmc: sdio: avoid spurious calls to interrupt handlers
Commit 06e8935feb ("optimized SDIO IRQ handling for single irq")
introduced some spurious calls to SDIO function interrupt handlers,
such as when the SDIO IRQ thread is started, or the safety check
performed upon a system resume.  Let's add a flag to perform the
optimization only when a real interrupt is signaled by the host
driver and we know there is no point confirming it.

Reported-by: Sujit Reddy Thumma <sthumma@codeaurora.org>
Signed-off-by: Nicolas Pitre <nico@linaro.org>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
2012-04-22 11:17:28 -04:00
Chuanxiao Dong 32d317c60e mmc: remove MMC bus legacy suspend/resume method
MMC bus is using legacy suspend/resume method, which is not compatible if
runtime pm callbacks are used. In this scenario, MMC bus suspend/resume
callbacks cannot be called when system entering S3. So change to use the
new defined dev_pm_ops for system sleeping mode.

Tested on AM335x Platform. Solves major issue/crash reported at
http://www.mail-archive.com/linux-omap@vger.kernel.org/msg65425.html

Signed-off-by: Chuanxiao Dong <chuanxiao.dong@intel.com>
Tested-by: Hebbar, Gururaja <gururaja.hebbar@ti.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Ulf Hansson <ulf.hansson@stericsson.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
2012-04-20 20:30:19 -04:00
Linus Torvalds b5174fa3a7 MMC highlights for 3.4:
Core:
  * Support for MMC 4.5 Data Tag feature -- we tag REQ_META, so devices
    that support Data Tag will provide increased throughput for metadata.
  * Faster detection of card removal on I/O errors.
 
 Drivers:
  * dw_mmc now supports eMMC Power Off Notify, has PCI support, and
    implements pre_req and post_req for asynchronous requests.
  * omap_hsmmc now supports device tree.
  * esdhc now has power management support.
  * sdhci-tegra now supports Tegra30 devices.
  * sdhci-spear now supports hibernation.
  * tmio_mmc now supports using a GPIO for card detection.
  * Intel PCH now supports 8-bit bus transfers.
 -----BEGIN PGP SIGNATURE-----
 Version: GnuPG v1.4.11 (GNU/Linux)
 
 iQIcBAABAgAGBQJPcejzAAoJEHNBYZ7TNxYM1eEQALs8LAoHcp9vdG2Uttz65HQL
 ISavfZIVTiLO22ugg5NKXdAOSAv0xdIeuUdpsxRr3W7j27OP41KLq1V7U+Mvnzm0
 VG+99J4kdrpgIe+ogvq9IHsnCQZ8ERSzTd2My+O1l9O0jYAAJ2mnsyljlMnaCFS4
 lac4/1wlGpogz8UXCEL54V1LJFWW2YWJ6wrjcsu4gaJMyAFk83rbUP1XnlZJOZL2
 Z8e8AHh30tJ+dWOGUJRzdRhy6R1pMNabiUP/U+m9pvcTNdGYYbSGDKvmVmSzQOLH
 VtD7wzfQysj1ReVr2zyhkMif/el/F80JesRrAE7xS2IYJvhj5RmADQY8fE+KKFD9
 n+6UkfHbI+ikRZgyeivqlnGC2j2YZ1DqxnptbfBuMPuvAliE6JjQuNunCo0jyl6o
 +uZ8f84Dq3mZ/6ldb7vKbwvNZXVzUNlB4thH1MqWXDDXb1YUS5jXO7jBRhgvhLXg
 Wb9Pbi92QMArrq8c0Ch1Yy0ufZZEJ2wTh2Sp2vBqvVEEZ7X3R3GUFGmsCqwS9Ew1
 NSSMsc+ANNKY3/qDC7vyyCIuYVqTrZmi0Zr/IcTCGy0YcFJiK5bblJeL9l1kYOyo
 3KPno/ZkC+qZSHGCab9RvRWemqdAgTwdxch+BalXLVt4NhRGNIMeBOVNSMsbeP9e
 aA33LGNp258Jdphmv0NE
 =T4T+
 -----END PGP SIGNATURE-----

Merge tag 'mmc-merge-for-3.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc

Pull MMC updates from Chris Ball:

Core:
 * Support for MMC 4.5 Data Tag feature -- we tag REQ_META, so devices
   that support Data Tag will provide increased throughput for metadata.
 * Faster detection of card removal on I/O errors.

Drivers:
 * dw_mmc now supports eMMC Power Off Notify, has PCI support, and
   implements pre_req and post_req for asynchronous requests.
 * omap_hsmmc now supports device tree.
 * esdhc now has power management support.
 * sdhci-tegra now supports Tegra30 devices.
 * sdhci-spear now supports hibernation.
 * tmio_mmc now supports using a GPIO for card detection.
 * Intel PCH now supports 8-bit bus transfers.

* tag 'mmc-merge-for-3.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc: (53 commits)
  mmc: sh_mmcif: simplify bitmask macros
  mmc: sh_mobile_sdhi: support modular mmc-core with non-standard hotplug
  mmc: sh_mobile_sdhi: add a callback for board specific init code
  mmc: tmio: cosmetic: prettify the tmio_mmc_set_ios() function
  mmc: sh_mobile_sdhi: do not manage PM clocks manually
  mmc: tmio_mmc: remove unused sdio_irq_enabled flag
  mmc: tmio_mmc: power status flag doesn't have to be exposed in platform data
  mmc: sh_mobile_sdhi: pass card hotplug GPIO number to TMIO MMC
  mmc: tmio_mmc: support the generic MMC GPIO card hotplug helper
  mmc: tmio: calculate the native hotplug condition only once
  mmc: simplify mmc_cd_gpio_request() by removing two parameters
  mmc: sdhci-pci: allow 8-bit bus width for Intel PCH
  mmc: sdhci: check interrupt flags in ISR again
  mmc: sdhci-pci: Add MSI support
  mmc: core: warn when card doesn't support HPI
  mmc: davinci: Poll status for small size transfers
  mmc: davinci: Eliminate spurious interrupts
  mmc: omap_hsmmc: Avoid a regulator voltage change with dt
  mmc: omap_hsmmc: Convert hsmmc driver to use device tree
  mmc: sdhci-pci: add SDHCI_QUIRK2_HOST_OFF_CARD_ON for Medfield SDIO
  ...
2012-03-28 20:59:45 -07:00
Guennadi Liakhovetski 135111cc55 mmc: sh_mmcif: simplify bitmask macros
Purely cosmetic readability improvement, no functional change.

Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
2012-03-27 12:20:20 -04:00
Guennadi Liakhovetski 7f52421743 mmc: sh_mobile_sdhi: support modular mmc-core with non-standard hotplug
Currently if a platform wants to implement a non-standard card-detection
method, it would need to call tmio_mmc_cd_wakeup(), which is an inline
function, calling mmc_detect_change(). For this the platform would have
to link mmc_core statically into the kernel, losing the ability to build
it as a module. This patch adds a callback to the sh_mobile_sdhi driver,
which eliminates this dependency.

Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Chris Ball <cjb@laptop.org>
2012-03-27 12:20:19 -04:00
Bastian Hecht e82b4ac94e mmc: sh_mobile_sdhi: add a callback for board specific init code
Some boards need a preliminary setup stage to prepare the sdhi
controller.

Signed-off-by: Bastian Hecht <hechtb@gmail.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
2012-03-27 12:20:19 -04:00
Guennadi Liakhovetski 58126c878b mmc: sh_mobile_sdhi: pass card hotplug GPIO number to TMIO MMC
To use TMIO MMC driver ability to interface to the generic MMC GPIO card
hotplug detection helper, the SDHI driver has to pass the GPIO number
from its own platform data.

Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
2012-03-27 12:20:16 -04:00
Guennadi Liakhovetski c9b0546a59 mmc: simplify mmc_cd_gpio_request() by removing two parameters
Calculate the IRQ number, using gpio_to_irq() and use fixed flags: trigger
on both edges. This makes two out of four arguments of the
mmc_cd_gpio_request() function redundant.

Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
2012-03-27 12:20:14 -04:00
Adrian Hunter 6308d2905b mmc: sdhci: add quirk for keeping card power during suspend
Add quirk SDHCI_QUIRK2_HOST_OFF_CARD_ON to cater for the case when the
card keeps power during suspend but the host controller does not i.e.
the card power is not controlled by the host controller.  In that
case, the controller must be fully reset on resume.

Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
2012-03-27 12:20:08 -04:00
Adrian Hunter 83bb24aaa4 mmc: core: add high-capacity erase size capability flag
Let drivers specify the use of high-capacity erase size.

Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
2012-03-27 12:20:07 -04:00
Adrian Hunter 907d2e7cc7 mmc: start removing enable / disable API
Most parts of the enable / disable API are no longer used and
can be removed.

Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Tested-by: Venkatraman S <svenkatr@ti.com>
Tested-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
2012-03-27 12:20:03 -04:00
Ulf Hansson f0cc9cf993 mmc: core: Detect card removal on I/O error
To prevent I/O as soon as possible at card removal, a new detect work is
re-scheduled without a delay to let a rescan remove the card device as
soon as possible.

Additionally, MMC_CAP2_DETECT_ON_ERR can now be used to handle "slowly"
removed cards that a scheduled detect work did not detect as removed.
To prevent further I/O requests for these lingering removed cards,
check if card has been removed and then schedule a detect work to
properly remove it.

Signed-off-by: Ulf Hansson <ulf.hansson@stericsson.com>
Reviewed-by: Namjae Jeon <linkinjeon@gmail.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
2012-03-27 12:19:58 -04:00
Shashidhar Hiremath 62ca8034d9 mmc: Support of PCI mode in the dw_mmc driver
Support of PCI mode for the dw_mmc driver. This Patch adds the
support for the scenario where the Synopsys Designware IP
is present on the PCI bus. The patch adds the minimal modifications
necessary for the driver to work on PCI platform. Also added separate
files for PCI and PLATFORM modes of operation.

Signed-off-by: Shashidhar Hiremath <shashidharh@vayavyalabs.com>
Acked-by: James Hogan <james.hogan@imgtec.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
2012-03-25 19:33:44 -04:00
Saugata Das 4265900e0b mmc: MMC-4.5 Data Tag Support
MMC-4.5 data tag feature will be used to store the file system meta-data
in the tagged region of eMMC. This will improve the write and subsequent
read transfer time for the meta data.

Signed-off-by: Saugata Das <saugata.das@linaro.org>
Tested-by: Venkatraman S <svenkatr@ti.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
2012-03-25 19:33:44 -04:00
Linus Torvalds 250f6715a4 The following text was taken from the original review request:
"[RFC PATCH 0/2] audit of linux/device.h users in include/*"
 		https://lkml.org/lkml/2012/3/4/159
 --
 
 Nearly every subsystem has some kind of header with a proto like:
 
 	void foo(struct device *dev);
 
 and yet there is no reason for most of these guys to care about the
 sub fields within the device struct.  This allows us to significantly
 reduce the scope of headers including headers.  For this instance, a
 reduction of about 40% is achieved by replacing the include with the
 simple fact that the device is some kind of a struct.
 
 Unlike the much larger module.h cleanup, this one is simply two
 commits.  One to fix the implicit <linux/device.h> users, and then
 one to delete the device.h includes from the linux/include/ dir
 wherever possible.
 -----BEGIN PGP SIGNATURE-----
 Version: GnuPG v1.4.11 (GNU/Linux)
 
 iQIcBAABAgAGBQJPbNxLAAoJEOvOhAQsB9HWR6QQAMRUZ94O2069/nW9h4TO/xTr
 Hq/80lo/TBBiRmob3iWBP76lzgeeMPPVEX1I6N7YYlhL3IL7HsaJH1DvpIPPHXQP
 GFKcBsZ5ZLV8c4CBDSr+/HFNdhXc0bw0awBjBvR7gAsWuZpNFn4WbhizJi4vWAoE
 4ydhPu55G1G8TkBtYLJQ8xavxsmiNBSDhd2i+0vn6EVpgmXynjOMG8qXyaS97Jvg
 pZLwnN5Wu21coj6+xH3QUKCl1mJ+KGyamWX5gFBVIfsDB3k5H4neijVm7t1en4b0
 cWxmXeR/JE3VLEl/17yN2dodD8qw1QzmTWzz1vmwJl2zK+rRRAByBrL0DP7QCwCZ
 ppeJbdhkMBwqjtknwrmMwsuAzUdJd79GXA+6Vm+xSEkr6FEPK1M0kGbvaqV9Usgd
 ohMewewbO6ddgR9eF7Kw2FAwo0hwkPNEplXIym9rZzFG1h+T0STGSHvkn7LV765E
 ul1FapSV3GCxEVRwWTwD28FLU2+0zlkOZ5sxXwNPTT96cNmW+R7TGuslZKNaMNjX
 q7eBZxo8DtVt/jqJTntR8bs8052c8g1Ac1IKmlW8VSmFwT1M6VBGRn1/JWAhuUgv
 dBK/FF+I1GJTAJWIhaFcKXLHvmV9uhS6JaIhLMDOetoOkpqSptJ42hDG+89WkFRk
 o55GQ5TFdoOpqxVzGbvE
 =3j4+
 -----END PGP SIGNATURE-----

Merge tag 'device-for-3.4' of git://git.kernel.org/pub/scm/linux/kernel/git/paulg/linux

Pull <linux/device.h> avoidance patches from Paul Gortmaker:
 "Nearly every subsystem has some kind of header with a proto like:

	void foo(struct device *dev);

  and yet there is no reason for most of these guys to care about the
  sub fields within the device struct.  This allows us to significantly
  reduce the scope of headers including headers.  For this instance, a
  reduction of about 40% is achieved by replacing the include with the
  simple fact that the device is some kind of a struct.

  Unlike the much larger module.h cleanup, this one is simply two
  commits.  One to fix the implicit <linux/device.h> users, and then one
  to delete the device.h includes from the linux/include/ dir wherever
  possible."

* tag 'device-for-3.4' of git://git.kernel.org/pub/scm/linux/kernel/git/paulg/linux:
  device.h: audit and cleanup users in main include dir
  device.h: cleanup users outside of linux/include (C files)
2012-03-24 10:41:37 -07:00
Bobby Powers 10db4e1e4e headers: include linux/types.h where appropriate
This addresses some header check warnings.  DRM headers which include
"drm.h" have been excluded, as they indirectly include types.h.

Signed-off-by: Bobby Powers <bobbypowers@gmail.com>
Cc: Chris Ball <cjb@laptop.org>
Cc: Dave Airlie <airlied@linux.ie>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Cc: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2012-03-23 16:58:31 -07:00
Paul Gortmaker 313162d0b8 device.h: audit and cleanup users in main include dir
The <linux/device.h> header includes a lot of stuff, and
it in turn gets a lot of use just for the basic "struct device"
which appears so often.

Clean up the users as follows:

1) For those headers only needing "struct device" as a pointer
in fcn args, replace the include with exactly that.

2) For headers not really using anything from device.h, simply
delete the include altogether.

3) For headers relying on getting device.h implicitly before
being included themselves, now explicitly include device.h

4) For files in which doing #1 or #2 uncovers an implicit
dependency on some other header, fix by explicitly adding
the required header(s).

Any C files that were implicitly relying on device.h to be
present have already been dealt with in advance.

Total removals from #1 and #2: 51.  Total additions coming
from #3: 9.  Total other implicit dependencies from #4: 7.

As of 3.3-rc1, there were 110, so a net removal of 42 gives
about a 38% reduction in device.h presence in include/*

Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
2012-03-16 10:38:24 -04:00
Seungwon Jeon f9c2a0dc42 mmc: dw_mmc: Fix PIO mode with support of highmem
Current PIO mode makes a kernel crash with CONFIG_HIGHMEM.
Highmem pages have a NULL from sg_virt(sg).
This patch fixes the following problem.

Unable to handle kernel NULL pointer dereference at virtual address 00000000
pgd = c0004000
[00000000] *pgd=00000000
Internal error: Oops: 817 [#1] PREEMPT SMP
Modules linked in:
CPU: 0    Not tainted  (3.0.15-01423-gdbf465f #589)
PC is at dw_mci_pull_data32+0x4c/0x9c
LR is at dw_mci_read_data_pio+0x54/0x1f0
pc : [<c0358824>]    lr : [<c035988c>]    psr: 20000193
sp : c0619d48  ip : c0619d70  fp : c0619d6c
r10: 00000000  r9 : 00000002  r8 : 00001000
r7 : 00000200  r6 : 00000000  r5 : e1dd3100  r4 : 00000000
r3 : 65622023  r2 : 0000007f  r1 : eeb96000  r0 : e1dd3100
Flags: nzCv  IRQs off  FIQs on  Mode SVC_32  ISA ARM  Segment
xkernel
Control: 10c5387d  Table: 61e2004a  DAC: 00000015
Process swapper (pid: 0, stack limit = 0xc06182f0)
Stack: (0xc0619d48 to 0xc061a000)
9d40:                   e1dd3100 e1a4f000 00000000 e1dd3100 e1a4f000 00000200
9d60: c0619da4 c0619d70 c035988c c03587e4 c0619d9c e18158f4 e1dd3100 e1dd3100
9d80: 00000020 00000000 00000000 00000020 c06e8a84 00000000 c0619e04 c0619da8
9da0: c0359b24 c0359844 e18158f4 e1dd3164 e1dd3168 e1dd3150 3d02fc79 e1dd3154
9dc0: e1dd3178 00000000 00000020 00000000 e1dd3150 00000000 c10dd7e8 e1a84900
9de0: c061e7cc 00000000 00000000 0000008d c06e8a84 c061e780 c0619e4c c0619e08
9e00: c00c4738 c0359a34 3d02fc79 00000000 c0619e4c c05a1698 c05a1670 c05a165c
9e20: c04de8b0 c061e780 c061e7cc e1a84900 ffffed68 0000008d c0618000 00000000
9e40: c0619e6c c0619e50 c00c48b4 c00c46c8 c061e780 c00423ac c061e7cc ffffed68
9e60: c0619e8c c0619e70 c00c7358 c00c487c 0000008d ffffee38 c0618000 ffffed68
9e80: c0619ea4 c0619e90 c00c4258 c00c72b0 c00423ac ffffee38 c0619ecc c0619ea8
9ea0: c004241c c00c4234 ffffffff f8810000 0000006d 00000002 00000001 7fffffff
9ec0: c0619f44 c0619ed0 c0048bc0 c00423c4 220ae7a9 00000000 386f0d30 0005d3a4
9ee0: c00423ac c10dd0b8 c06f2cd8 c0618000 c0594778 c003a674 7fffffff c0619f44
9f00: 386f0d30 c0619f18 c00a6f94 c005be3c 80000013 ffffffff 386f0d30 0005d3a4
9f20: 386f0d30 0005d2d1 c10dd0a8 c10dd0b8 c06f2cd8 c0618000 c0619f74 c0619f48
9f40: c0345858 c005be00 c00a2440 c0618000 c0618000 c00410d8 c06c1944 c00410fc
9f60: c0594778 c003a674 c0619f9c c0619f78 c004a7e8 c03457b4 c0618000 c06c18f8
9f80: 00000000 c0039c70 c06c18d4 c003a674 c0619fb4 c0619fa0 c04ceafc c004a714
9fa0: c06287b4 c06c18f8 c0619ff4 c0619fb8 c0008b68 c04cea68 c0008578 00000000
9fc0: 00000000 c003a674 00000000 10c5387d c0628658 c003aa78 c062f1c4 4000406a
9fe0: 413fc090 00000000 00000000 c0619ff8 40008044 c0008858 00000000 00000000
Backtrace:
[<c03587d8>] (dw_mci_pull_data32+0x0/0x9c) from [<c035988c>] (dw_mci_read_data_pio+0x54/0x1f0)
 r6:00000200 r5:e1a4f000 r4:e1dd3100
 [<c0359838>] (dw_mci_read_data_pio+0x0/0x1f0) from [<c0359b24>] (dw_mci_interrupt+0xfc/0x4a4)
[<c0359a28>] (dw_mci_interrupt+0x0/0x4a4) from [<c00c4738>] (handle_irq_event_percpu+0x7c/0x1b4)
[<c00c46bc>] (handle_irq_event_percpu+0x0/0x1b4) from [<c00c48b4>] (handle_irq_event+0x44/0x64)
[<c00c4870>] (handle_irq_event+0x0/0x64) from [<c00c7358>] (handle_fasteoi_irq+0xb4/0x124)
 r7:ffffed68 r6:c061e7cc r5:c00423ac r4:c061e780
 [<c00c72a4>] (handle_fasteoi_irq+0x0/0x124) from [<c00c4258>] (generic_handle_irq+0x30/0x38)
 r7:ffffed68 r6:c0618000 r5:ffffee38 r4:0000008d
 [<c00c4228>] (generic_handle_irq+0x0/0x38) from [<c004241c>] (asm_do_IRQ+0x64/0xe0)
 r5:ffffee38 r4:c00423ac
 [<c00423b8>] (asm_do_IRQ+0x0/0xe0) from [<c0048bc0>] (__irq_svc+0x80/0x14c)
Exception stack(0xc0619ed0 to 0xc0619f18)

Signed-off-by: Seungwon Jeon <tgih.jun@samsung.com>
Acked-by: Will Newton <will.newton@imgtec.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
2012-02-13 20:39:05 -05:00
Girish K S 3e73c36b4d mmc: core: Fix PowerOff Notify suspend/resume
Modified the mmc_poweroff to resume before sending the poweroff
notification command. In sleep mode only AWAKE and RESET commands are
allowed, so before sending the poweroff notification command resume from
sleep mode and then send the notification command.

PowerOff Notify is tested on a Synopsis Designware Host Controller
(eMMC 4.5). The suspend to RAM and resume works fine.

Signed-off-by: Girish K S <girish.shivananjappa@linaro.org>
Tested-by: Girish K S <girish.shivananjappa@linaro.org>
Reviewed-by: Saugata Das <saugata.das@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
2012-02-13 20:39:02 -05:00
Jaehoon Chung 6e8201f57c mmc: core: add the capability for broken voltage
There is an understood mismatch between the voltage the host controller is
set to and the voltage supplied to the card by a fixed voltage regulator.
Teaching the driver to accept the mismatch is overly complicated.  Instead
just accept the regulator's voltage.

This patch adds MMC_CAP2_BROKEN_VOLTAGE.

If the voltage didn't satisfy between min_uV and max_uV, try to change
the voltage in core.c.  When changing the voltage, maybe use
regulator_set_voltage().

In regulator_set_voltage(), check the below condition.

	/* sanity check */
	if (!rdev->desc->ops->set_voltage &&
	    !rdev->desc->ops->set_voltage_sel) {
		ret = -EINVAL;
		goto out;
	}

If some board should use the fixed-regulator, always return -EINVAL.
Then, eMMC didn't initialize always.

So if use a fixed-regulator, we need to add the MMC_CAP2_BROKEN_VOLTAGE.

Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
2012-02-13 20:39:01 -05:00
Sujit Reddy Thumma 2c4967f741 mmc: core: Ensure clocks are always enabled before host interaction
Ensure clocks are always enabled before any interaction with the
host controller driver. This makes sure that there is no race
between host execution and the core layer turning off clocks
in different context with clock gating framework.

Signed-off-by: Sujit Reddy Thumma <sthumma@codeaurora.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Per Forlin <per.forlin@stericsson.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
2012-02-13 20:38:58 -05:00
Linus Torvalds 0a80939b3e Autogenerated GPG tag for Rusty D1ADB8F1: 15EE 8D6C AB0E 7F0C F999 BFCB D920 0E6C D1AD B8F1
-----BEGIN PGP SIGNATURE-----
 Version: GnuPG v1.4.11 (GNU/Linux)
 
 iQIcBAABAgAGBQJPD2aFAAoJENkgDmzRrbjxNzsQAIeYbbrXYLjr6kQzUSngj/eC
 FzjaTEfYTQIeuQCFJHcHthyc5lXV4sQbo3jOezW+Bp5yuDJL2aWIHesSfWZe7imu
 zQdM4VshOYdAmUR9Q0AW5zhB8Smbs7/AyABiF2jm4p0ZPOuyMDSlei9sjvE9Vjvt
 B7g5ht7L6kz0JbDnwwy0u5gs+tEitwpXYId9Y4ysZIBzIbL0qkPX8veOddGTMy0N
 8xhWXaKtufpjvxFD2ORLDsw3AkoF1xXSNuFd/5nzCNpbeE7TW931jfkPoqJumuAO
 7GLxcU9kKYl+IICobC6wBtsj/RrB7w+cBXMvPGwdBliam1qaRhUcJZi5FLM/Ha5d
 2A9QDYNUpoXiO8JbPXrV9Z+Y0+Co8RilsQj7R/rjZh6AbbYCWt9nxzx2Svl/RfTr
 xfiimHuB2P3rHjOvpCXULwOOuE5c8MzPuWncpdjiD3uGXOY/aY+X1m+if/quJw9D
 grPlKL0+YiRakEYUeGG4M77KCqyKFZaF7L7UQPbqfZcj8V/9AW3/7U5I/B9RlAjs
 idsr4fcf5s0N+oKUyTCW1ncpUDQNiwbU2NyJQqeu1ZxaRGj72AgyvsaNeyIPDyK+
 f6x95Bi7i8KLjXc9Z1KvJwh2Nxt25gNUiTYVha/9H2NpJGd1cfI15kTOGXrgddVv
 1pvuGcJDZwYiwfiXr3FL
 =HHrh
 -----END PGP SIGNATURE-----

Merge tag 'for-linus' of git://github.com/rustyrussell/linux

Autogenerated GPG tag for Rusty D1ADB8F1: 15EE 8D6C AB0E 7F0C F999  BFCB D920 0E6C D1AD B8F1

* tag 'for-linus' of git://github.com/rustyrussell/linux:
  module_param: check that bool parameters really are bool.
  intelfbdrv.c: bailearly is an int module_param
  paride/pcd: fix bool verbose module parameter.
  module_param: make bool parameters really bool (drivers & misc)
  module_param: make bool parameters really bool (arch)
  module_param: make bool parameters really bool (core code)
  kernel/async: remove redundant declaration.
  printk: fix unnecessary module_param_name.
  lirc_parallel: fix module parameter description.
  module_param: avoid bool abuse, add bint for special cases.
  module_param: check type correctness for module_param_array
  modpost: use linker section to generate table.
  modpost: use a table rather than a giant if/else statement.
  modules: sysfs - export: taint, coresize, initsize
  kernel/params: replace DEBUGP with pr_debug
  module: replace DEBUGP with pr_debug
  module: struct module_ref should contains long fields
  module: Fix performance regression on modules with large symbol tables
  module: Add comments describing how the "strmap" logic works

Fix up conflicts in scripts/mod/file2alias.c due to the new linker-
generated table approach to adding __mod_*_device_table entries.  The
ARM sa11x0 mcp bus needed to be converted to that too.
2012-01-14 12:32:16 -08:00
Rusty Russell 90ab5ee941 module_param: make bool parameters really bool (drivers & misc)
module_param(bool) used to counter-intuitively take an int.  In
fddd5201 (mid-2009) we allowed bool or int/unsigned int using a messy
trick.

It's time to remove the int/unsigned int option.  For this version
it'll simply give a warning, but it'll break next kernel version.

Acked-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
2012-01-13 09:32:20 +10:30
Girish K S 069c9f1428 mmc: host: Adds support for eMMC 4.5 HS200 mode
This patch adds support for the HS200 mode on the host side.
Also enables the tuning feature required when the HS200 mode
is selected.

Signed-off-by: Girish K S <girish.shivananjappa@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
2012-01-12 15:17:16 -05:00
Girish K S a4924c71aa mmc: core: HS200 mode support for eMMC 4.5
This patch adds the support of the HS200 bus speed for eMMC 4.5 devices.
The eMMC 4.5 devices have support for 200MHz bus speed. The function
prototype of the tuning function is modified to handle the tuning
command number which is different in sd and mmc case.

Signed-off-by: Girish K S <girish.shivananjappa@linaro.org>
Signed-off-by: Philip Rakity <prakity@marvell.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
2012-01-12 15:17:15 -05:00
Ulf Hansson aa9df4fb2a mmc: core: Add option to prevent eMMC sleep command
Host may now use MMC_CAP2_NO_SLEEP_CMD to disable the use
of eMMC sleep/awake command.

This option can be used when your platform has a buggy
kernel crash dump software, which is supposed to store
the dump on the eMMC, but is not able to wake up the eMMC
from sleep state.

In particular, failures have been seen with u-boot; even if
it is fixed there, platforms will be slow to update their
bootloader binaries.

Signed-off-by: Ulf Hansson <ulf.hansson@stericsson.com>
Reviewed-by: Hanumath Prasad <hanumath.prasad@stericsson.com>
Reviewed-by: Srinidhi Kasagar <srinidhi.kasagar@stericsson.com>
Acked-by: Subhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
2012-01-11 23:58:48 -05:00
Adrian Hunter e2a0a5829c mmc: sdhci-pci: remove SDHCI_QUIRK2_OWN_CARD_DETECTION
Even if a driver provides separate card detection, an interrupt
is still needed to abort mmc requests that are in progress.
SDHCI_QUIRK2_OWN_CARD_DETECTION prevents that, so remove it.

Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
2012-01-11 23:58:47 -05:00
Adrian Hunter 52c506f0bc mmc: sdhci-pci: add platform data
Add a means of getting platform data for the SDHCI PCI
devices.  The data is stored against the slot not the
device in order to support multi-slot devices.

The data allows platform-specific setup (such as getting
GPIO numbers from firmware or setting up wl12xx for SDIO)
to be done in platform support files instead of the
sdhci-pci driver.

Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
2012-01-11 23:58:47 -05:00
Guennadi Liakhovetski 349ab52446 mmc: add a generic GPIO card-detect helper
This patch adds a primitive helper to support card hotplug detection on
platforms, where a GPIO, capable of producing interrupts, is used for
detection of card-insertion and -removal events.

Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
2012-01-11 23:58:45 -05:00
Guennadi Liakhovetski b67e198073 mmc: add a card hotplug handler context
SD/MMC controllers provide different card insertion and removal detection
methods. On some of them the controller itself issues an interrupt, on
others polling is used, on yet others auxiliary means are used for this
purpose, e.g., a GPIO IRQ. Further, on some systems one of those methods
can be chosen at driver probing time and configured in software. E.g., on
some systems the SD/MMC controller card hot-plug detection pin can be
configured either as a respective controller functions, or an IRQ-capable
GPIO. To support such flexible configurations a card hot-plug context
is added by this patch.

Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
2012-01-11 23:58:45 -05:00
Seungwon Jeon 4f408cc67a mmc: dw_mmc: Add more capabilities field
This patch adds another capabilities field for MMC_CAPS2_XXX.

Signed-off-by: Seungwon Jeon <tgih.jun@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
2012-01-11 23:58:44 -05:00
Johan Rudholm add710eaa8 mmc: boot partition ro lock support
Enable boot partitions to be read-only locked until next power on via
a sysfs entry. There will be one sysfs entry for each boot partition:

/sys/block/mmcblkXbootY/ro_lock_until_next_power_on

Each boot partition is locked by writing 1 to its file.

Signed-off-by: Johan Rudholm <johan.rudholm@stericsson.com>
Signed-off-by: John Beckett <john.beckett@stericsson.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
2012-01-11 23:58:43 -05:00
Adrian Hunter d304950488 mmc: allow upper layers to know immediately if card has been removed
Add a function mmc_detect_card_removed() which upper layers can use to
determine immediately if a card has been removed. This function should
be called after an I/O request fails so that all queued I/O requests
can be errored out immediately instead of waiting for the card device
to be removed.

Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Acked-by: Sujit Reddy Thumma <sthumma@codeaurora.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
2012-01-11 23:58:43 -05:00
Philip Rakity a303c5319c mmc: sdio: support SDIO UHS cards
This patch adds support for sdio UHS cards per the version 3.0
spec.

UHS mode is only enabled for version 3.0 cards when both the
host and the controller support UHS modes.

1.8v signaling support is removed if both the card and the
host do not support UHS.  This is done to maintain
compatibility and some system/card combinations break when
1.8v signaling is enabled when the host does not support UHS.

Signed-off-by: Philip Rakity <prakity@marvell.com>
Signed-off-by: Aaron Lu <Aaron.lu@amd.com>
Reviewed-by: Arindam Nath <arindam.nath@amd.com>
Tested-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
2012-01-11 23:58:41 -05:00
Sujit Reddy Thumma 597dd9d79c mmc: core: Use delayed work in clock gating framework
Current clock gating framework disables the MCI clock as soon as the
request is completed and enables it when a request arrives. This aggressive
clock gating framework, when enabled, cause following issues:

When there are back-to-back requests from the Queue layer, we unnecessarily
end up disabling and enabling the clocks between these requests since 8MCLK
clock cycles is a very short duration compared to the time delay between
back to back requests reaching the MMC layer. This overhead can effect the
overall performance depending on how long the clock enable and disable
calls take which is platform dependent. For example on some platforms we
can have clock control not on the local processor, but on a different
subsystem and the time taken to perform the clock enable/disable can add
significant overhead.

Also if the host controller driver decides to disable the host clock too
when mmc_set_ios function is called with ios.clock=0, it adds additional
delay and it is highly possible that the next request had already arrived
and unnecessarily blocked in enabling the clocks. This is seen frequently
when the processor is executing at high speeds and in multi-core platforms
thus reduces the overall throughput compared to if clock gating is
disabled.

Fix this by delaying turning off the clocks by posting request on
delayed workqueue. Also cancel the unscheduled pending work, if any,
when there is access to card.

sysfs entry is provided to tune the delay as needed, default
value set to 200ms.

Signed-off-by: Sujit Reddy Thumma <sthumma@codeaurora.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
2012-01-11 23:58:41 -05:00
Giuseppe CAVALLARO df16219f36 mmc: debugfs: expose the SDCLK frq in sys ios
This patch is to expose the actual SDCLK frequency in
/sys/kernel/debug/mmcX/ios entry.

For example, if the max clk for a normal speed card is 20MHz this
is reported in /sys/kernel/debug/mmcX/ios.  Unfortunately the actual
SDCLK frequency (i.e. Baseclock / divisor) is not reported at all:
for example, in that case, on Arasan HC, it should be 48/4=12 (MHz).

Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
2012-01-11 23:58:40 -05:00
Qiang Liu fffe5d5aa0 mmc: sd: Macro name cleanup for high speed dtr
Add new macros for the high speed 50MHz case, rather than having
a confusing reuse of the value for UHS SDR50, which is 100MHz.

Reported-by: Aaron Lu <aaron.lu@amd.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
2012-01-11 23:58:40 -05:00
Stefan Nilsson XK 6de5fc9cf7 mmc: core: Add quirk for long data read time
Adds a quirk that sets the data read timeout to a fixed value instead
of relying on the information in the CSD. The timeout value chosen
is 300ms since that has proven enough for the problematic cards found,
but could be increased if other cards require this.

This patch also enables this quirk for certain Micron cards known to
have this problem.

Signed-off-by: Stefan Nilsson XK <stefan.xk.nilsson@stericsson.com>
Signed-off-by: Ulf Hansson <ulf.hansson@stericsson.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Cc: <stable@kernel.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
2011-12-10 16:18:35 -05:00
Namjae Jeon a6029e1f75 mmc: fix compile error when CONFIG_BLOCK is not enabled
'DISK_NAME_LEN' is undeclared when CONFIG_BLOCK is disabled; its use was
introduced via genhd.h by the general purpose partition patch.

To fix, we just add our own MAX_MMC_PART_NAME_LEN macro instead of using
DISK_NAME_LEN.

Reported-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Namjae Jeon <linkinjeon@gmail.com>
Acked-by: Randy Dunlap <rdunlap@xenotime.net>
Acked-by: Andrei Warkentin <andreiw@vmware.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
2011-10-27 09:11:34 -04:00
Paul Walmsley 2bf22b3982 mmc: core: add workaround for controllers with broken multiblock reads
Due to hardware bugs, some MMC host controllers don't support
multiple-block reads[1].  To resolve, add a new MMC capability flag,
MMC_CAP2_NO_MULTI_READ, which can be set by affected host controller
drivers.  When this capability is set, all reads will be issued one
sector at a time.

1. See for example Advisory 2.1.1.128 "MMC: Multiple Block Read
Operation Issue" in _OMAP3530/3525/3515/3503 Silicon Errata_
Revision F (October 2010) (SPRZ278F), available from
http://focus.ti.com/lit/er/sprz278f/sprz278f.pdf

Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Dave Hylands <dhylands@gmail.com>
Tested-by: Steve Sakoman <sakoman@gmail.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
2011-10-27 09:10:57 -04:00
Bing Zhao b4625dab2c mmc: recognise SDIO cards with SDIO_CCCR_REV 3.00
Table 6-2: CCCR bit Definitions, address 00h.  Part E1 SDIO Simplified
Specification Version 3.00, Feb. 25, 2011.

This patch has been tested with Marvell WLAN device SD8797.

Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
2011-10-26 16:32:31 -04:00
Jaehoon Chung eb0d8f135b mmc: core: support HPI send command
HPI command is defined in eMMC4.41.
This feature is important for eMMC4.5 devices.

Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
2011-10-26 16:32:29 -04:00
Seungwon Jeon 881d1c25f7 mmc: core: Add cache control for eMMC4.5 device
This patch adds cache feature of eMMC4.5 Spec.
If device supports cache capability, host can utilize some specific
operations.

Signed-off-by: Seungwon Jeon <tgih.jun@samsung.com>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
2011-10-26 16:32:28 -04:00
Kyungmin Park b3bf915308 mmc: core: new discard feature support at eMMC v4.5
MMC v4.5 supports the DISCARD feature (CMD38).  It's different from
trim and there's no check bit.  Currently it's only supported at v4.5.

Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
2011-10-26 16:32:27 -04:00
Kyungmin Park d9ddd62943 mmc: core: mmc sanitize feature support for v4.5
In the v4.5, there's no secure erase & trim support.
Instead it supports the sanitize feature.

Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
2011-10-26 16:32:26 -04:00
Jaehoon Chung 4e0a5adf46 mmc: dw_mmc: modify DATA register offset
In dw_mmc 2.40a spec, Data register's offset is changed.
Before we used Data register offset 0x100. but if somebody uses a
2.40a controller, we must use 0x200 for Data register.

This patch adds a version-id checking point and uses SDMMC_DATA(x)
instead of SDMMC_DATA.  It assumes 2.40a is the latest version.

Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: James Hogan <james.hogan@imgtec.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
2011-10-26 16:32:25 -04:00
Girish K S bec8726abc mmc: core: Add Power Off Notify Feature eMMC 4.5
This patch adds support for the power off notify feature, available in
eMMC 4.5 devices. If the host has support for this feature, then the
mmc core will notify the device by setting the POWER_OFF_NOTIFICATION
byte in the extended csd register with a value of 1 (POWER_ON).

For suspend mode short timeout is used, whereas for the normal poweroff
long timeout is used.

Signed-off-by: Girish K S <girish.shivananjappa@linaro.org>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
2011-10-26 16:32:23 -04:00
Seungwon Jeon b23cf0bd55 mmc: core: Add default timeout value for CMD6
EXT_CSD[248] includes the default maximum timeout for CMD6.
This field is added at eMMC4.5 Spec. And it can be used for default
timeout except for some operations which don't define the timeout
(i.e. background operation, sanitize, flush cache) in eMMC4.5 Spec.

Signed-off-by: Seungwon Jeon <tgih.jun@samsung.com>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
2011-10-26 16:32:21 -04:00
Adrian Hunter 66fd8ad510 mmc: sdhci-pci: add runtime pm support
Ths patch allows runtime PM for sdhci-pci, runtime suspending after
inactivity of 50ms and ensuring runtime resume before SDHC registers
are accessed.  During runtime suspend, interrupts are masked.
The host controller state is restored at runtime resume.

For Medfield, the host controller's card detect mechanism is
supplanted by an always-on GPIO which provides for card detect wake-up.

Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
2011-10-26 16:32:20 -04:00
Namjae Jeon e0c368d571 mmc: core: general purpose MMC partition support.
It allows gerneral purpose partitions in MMC Device.  And I try to simply
make mmc_blk_alloc_parts using mmc_part structure suggested by Andrei
Warkentin.  After patching, we see general purpose partitions like this:
> cat /proc/partitions
          179 0 847872 mmcblk0
          179 192 4096 mmcblk0gp3
          179 160 4096 mmcblk0gp2
          179 128 4096 mmcblk0gp1
          179 96  1052672 mmcblk0gp0
          179 64  1024 mmcblk0boot1
          179 32  1024 mmcblk0boot0

Signed-off-by: Namjae Jeon <linkinjeon@gmail.com>
Acked-by: Andrei Warkentin <awarkentin@vmware.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
2011-10-26 16:32:17 -04:00
Adrian Hunter f7c56ef2af mmc: block: support no access to boot partitions
Intel Medfield platform blocks access to eMMC boot partitions which
results in switch errors.  Since there is no access, mmcboot0/1
devices should not be created.  Add a host capability to reflect that.

Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
2011-10-26 16:32:15 -04:00
Girish K S b87d8dbf6c mmc: core: eMMC 4.5 Power Class Selection Feature
This patch adds the power class selection feature available for mmc
versions 4.0 and above.  During the enumeration stage before switching
to the lower data bus, check if the power class is supported for the
current bus width. If the power class is available then switch to the
power class and use the higher data bus. If power class is not supported
then switch to the lower data bus in a worst case.

Signed-off-by: Girish K S <girish.shivananjappa@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
2011-10-26 16:32:13 -04:00
Guennadi Liakhovetski 714c4a6e3a mmc: sh_mmcif: simplify platform data
Provide platforms with a simplified way to specify MMCIF DMA slave IDs in
a way, similar to SDHI and other sh_dma clients.

Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
2011-10-26 16:32:09 -04:00
Adrian Hunter b2499518b5 mmc: core: add eMMC hardware reset support
eMMC's may have a hardware reset line.  This patch provides a
host controller operation to implement hardware reset and
a function to reset and reinitialize the card.  Also, for MMC,
the reset is always performed before initialization.

The host must set the new host capability MMC_CAP_HW_RESET
to enable hardware reset.

Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
2011-10-26 16:32:05 -04:00
Per Forlin 7c8a2829c2 mmc: core: clarify how to use post_req in case of errors
The err condition in post_req() is set to undo a call made to pre_req()
that hasn't been started yet.  The err condition is not set if an MMC
request returns an error.

Signed-off-by: Per Forlin <per.forlin@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
2011-10-26 16:32:04 -04:00
Stefan Nilsson XK 9a0da648ff mmc: sdio: Workaround for dev with broken CMD53
Adds a quirk which can be turned on for SDIO devices that do not support
512 byte requests in byte mode during CMD53. These requests will always
be sent in block mode instead.

This patch also enables this quirk for ST-Ericsson CW1200 WLAN device.

Signed-off-by: Stefan Nilsson XK <stefan.xk.nilsson@stericsson.com>
Signed-off-by: Ulf HANSSON <ulf.hansson@stericsson.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
2011-10-26 16:32:02 -04:00
Simon Horman d5098cb63b mmc: sdhi: Allow named IRQs to use specific handlers
Allow named IRQs to use corresponding specific handlers. If named IRQs are
used, at least an "sdcard" IRQ has to be specified by the platform. If
names are not used, an arbitrary number of IRQs can be provided by the
platform, in which case the generic ISR will be used for each of them.

Cc: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Magnus Damm <magnus.damm@gmail.com>
Signed-off-by: Simon Horman <horms@verge.net.au>
[g.liakhovetski@gmx.de: style and typo corrections, platform data check]
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
2011-10-26 15:43:36 -04:00
Per Forlin 1b676f70c1 mmc: core: add random fault injection
This adds support to inject data errors after a completed host transfer.
The mmc core will return error even though the host transfer is successful.
This simple fault injection proved to be very useful to test the
non-blocking error handling in the mmc_blk_issue_rw_rq().
Random faults can also test how the host driver handles pre_req()
and post_req() in case of errors.

Signed-off-by: Per Forlin <per.forlin@linaro.org>
Acked-by: Akinobu Mita <akinobu.mita@gmail.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
2011-10-26 15:43:34 -04:00
Jaehoon Chung 7fd781e8f9 mmc: remove unused "ddr" parameter in struct mmc_ios
"mmc: dw_mmc: Fix DDR mode support" removed the last user.

Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
2011-08-13 14:50:32 -04:00
Philip Rakity ca8e99b32e mmc: core: Set non-default Drive Strength via platform hook
Non default Drive Strength cannot be set automatically.  It is a function
of the board design and only if there is a specific platform handler can
it be set.  The platform handler needs to take into account the board
design.  Pass to the platform code the necessary information.

For example:  The card and host controller may indicate they support HIGH
and LOW drive strength.  There is no way to know what should be chosen
without specific board knowledge.  Setting HIGH may lead to reflections
and setting LOW may not suffice.  There is no mechanism (like ethernet
duplex or speed pulses) to determine what should be done automatically.

If no platform handler is defined -- use the default value.

Signed-off-by: Philip Rakity <prakity@marvell.com>
Reviewed-by: Arindam Nath <arindam.nath@amd.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
2011-07-20 17:21:16 -04:00
Per Forlin aa8b683a7d mmc: core: add non-blocking mmc request function
Previously there has only been one function mmc_wait_for_req()
to start and wait for a request. This patch adds:

 * mmc_start_req() - starts a request wihtout waiting
   If there is on ongoing request wait for completion
   of that request and start the new one and return.
   Does not wait for the new command to complete.

This patch also adds new function members in struct mmc_host_ops
only called from core.c:

 * pre_req - asks the host driver to prepare for the next job
 * post_req - asks the host driver to clean up after a completed job

The intention is to use pre_req() and post_req() to do cache maintenance
while a request is active. pre_req() can be called while a request is
active to minimize latency to start next job. post_req() can be used after
the next job is started to clean up the request. This will minimize the
host driver request end latency. post_req() is typically used before
ending the block request and handing over the buffer to the block layer.

Add a host-private member in mmc_data to be used by pre_req to mark the
data. The host driver will then check this mark to see if the data is
prepared or not.

Signed-off-by: Per Forlin <per.forlin@linaro.org>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Venkatraman S <svenkatr@ti.com>
Tested-by: Sourav Poddar <sourav.poddar@ti.com>
Tested-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
2011-07-20 17:21:10 -04:00
James Hogan 03e8cb534e mmc: dw_mmc: fix stop when fallen back to PIO
There are several situations when dw_mci_submit_data_dma() decides to
fall back to PIO mode instead of using DMA, due to a short (to avoid
overhead) or "complex" (e.g. with unaligned buffers) transaction, even
though host->use_dma is set. However dw_mci_stop_dma() decides whether
to stop DMA or set the EVENT_XFER_COMPLETE event based on host->use_dma.
When falling back to PIO mode this results in data timeout errors
getting missed and the driver locking up.

Therefore add host->using_dma to indicate whether the current
transaction is using dma or not, and adjust dw_mci_stop_dma() to use
that instead.

Signed-off-by: James Hogan <james.hogan@imgtec.com>
Acked-by: Will Newton <will.newton@imgtec.com>
Tested-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
2011-07-20 17:21:05 -04:00
Adrian Hunter e056a1b5b6 mmc: queue: let host controllers specify maximum discard timeout
Some host controllers will not operate without a hardware
timeout that is limited in value.  However large discards
require large timeouts, so there needs to be a way to
specify the maximum discard size.

A host controller driver may now specify the maximum discard
timeout possible so that max_discard_sectors can be calculated.

However, for eMMC when the High Capacity Erase Group Size
is not in use, the timeout calculation depends on clock
rate which may change.  For that case Preferred Erase Size
is used instead.

Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
2011-07-20 17:21:03 -04:00
James Hogan 34b664a20e mmc: dw_mmc: handle unaligned buffers and sizes
Update functions for PIO pushing and pulling data to and from the FIFO
so that they can handle unaligned output buffers and unaligned buffer
lengths. This makes more of the tests in mmc_test pass.

Unaligned lengths in pulls are handled by reading the full FIFO item,
and storing the remaining bytes in a small internal buffer (part_buf).
The next data pull will copy data out of this buffer first before
accessing the FIFO again. Similarly, for pushes the final bytes that
don't fill a FIFO item are stored in the part_buf (or sent anyway if
it's the last transfer), and then the part_buf is included at the
beginning of the next buffer pushed.

Unaligned buffers in pulls are handled specially if the architecture
cannot do efficient unaligned accesses, by reading FIFO items into a
aligned local buffer, and memcpy'ing them into the output buffer, again
storing any remaining bytes in the internal buffer. Similarly for pushes
the buffer is memcpy'd into an aligned local buffer then written to the
FIFO.

Signed-off-by: James Hogan <james.hogan@imgtec.com>
Acked-by: Will Newton <will.newton@imgtec.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
2011-07-20 17:21:00 -04:00
James Hogan b86d825323 mmc: dw_mmc: don't hard code fifo depth, fix usage
The FIFO_DEPTH hardware configuration parameter can be found from the
power-on value of RX_WMark in the FIFOTH register. This is used to
initialise the watermarks, but when calculating the number of free fifo
spaces a preprocessor definition is used which is hard coded to 32.

Fix reading the value out of FIFOTH (the default value in the RX_WMark
field is FIFO_DEPTH-1 not FIFO_DEPTH). Allow the fifo depth to be
overriden by platform data (since a bootloader may have changed FIFOTH
making auto-detection unreliable). Store the fifo_depth for later use.
Also fix the calculation to find the number of free bytes in the fifo to
include the fifo depth in the left shift by the data shift, since the
fifo depth is measured in fifo items not bytes.

Signed-off-by: James Hogan <james.hogan@imgtec.com>
Acked-by: Will Newton <will.newton@imgtec.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
2011-07-20 17:20:59 -04:00
James Hogan 1791b13ea4 mmc: dw_mmc: convert card tasklet to workqueue
Convert the card insert/remove tasklet to a workqueue, and call the
setpower platform specific callback without the spinlock held. This
means neither of the setpower or get_cd callbacks are called from atomic
context which allows them to sleep.

Signed-off-by: James Hogan <james.hogan@imgtec.com>
Acked-by: Will Newton <will.newton@imgtec.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
2011-07-20 17:20:58 -04:00
Simon Horman 973ed3af1a mmc: sdhi: Add write16_hook
Some controllers require waiting for the bus to become idle
before writing to some registers. I have implemented this
by adding a hook to sd_ctrl_write16() and implementing
a hook for SDHI which waits for the bus to become idle.

Cc: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Cc: Magnus Damm <magnus.damm@gmail.com>
Signed-off-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Chris Ball <cjb@laptop.org>
2011-07-20 17:20:57 -04:00
Simon Horman 95c7348d94 mmc: tmio: name 0xd8 as CTL_DMA_ENABLE
This reflects at least the current usage of this register
and I think it improves the readability of the code ever so slightly.

Cc: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Cc: Magnus Damm <magnus.damm@gmail.com>
Signed-off-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Chris Ball <cjb@laptop.org>
2011-07-20 17:20:55 -04:00
Russell King - ARM Linux 0a2d4048a2 mmc: block: allow get_card_status() to return error status
If the MMC_SEND_STATUS command is not successful, we should not return
a zero status word, but instead allow the caller to know positively
that an error occurred.

Convert the open-coded get_card_status() to use the helper function,
and provide definitions for the card state field.

Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Tested-by: Pawel Moll <pawel.moll@arm.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
2011-07-20 17:20:54 -04:00
Robert P. J. Day 100e918610 mmc: Standardize header file inclusion checks.
Standardize the checks for multiple MMC header file inclusion,
including adding comments to terminating #endif's, and fixing
one incorrect comment.

Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca>
Signed-off-by: Chris Ball <cjb@laptop.org>
2011-07-20 17:20:48 -04:00
Shawn Guo 94cc6a8656 mmc: sdhci: merge two sdhci-pltfm.h into one
The structure sdhci_pltfm_data is not necessarily to be in a public
header like include/linux/mmc/sdhci-pltfm.h, so the patch moves it
into drivers/mmc/host/sdhci-pltfm.h and eliminates the former one.

Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Reviewed-by: Grant Likely <grant.likely@secretlab.ca>
Reviewed-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
2011-07-20 17:20:48 -04:00
Shawn Guo 85d6509dc8 mmc: sdhci: make sdhci-pltfm device drivers self registered
The patch turns the common stuff in sdhci-pltfm.c into functions, and
add device drivers their own .probe and .remove which in turn call
into the common functions, so that those sdhci-pltfm device drivers
register itself and keep all device specific things away from common
sdhci-pltfm file.

Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Reviewed-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Anton Vorontsov <cbouatmailru@gmail.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
2011-07-20 17:16:06 -04:00
Philip Rakity f39b2dd9d0 mmc: core: Bus width testing needs to handle suspend/resume
On reading the ext_csd for the first time (in 1 bit mode), save the
ext_csd information needed for bus width compare.

On every pass we make re-reading the ext_csd, compare the data
against the saved ext_csd data.

This fixes a regression introduced in 3.0-rc1 by 08ee80cc39
("mmc: core: eMMC bus width may not work on all platforms"), which
incorrectly assumed we would be re-reading the ext_csd at resume-
time.

Signed-off-by: Philip Rakity <prakity@marvell.com>
Tested-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
2011-07-13 14:54:37 -04:00
Linus Torvalds 8c1c77ff9b Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc: (75 commits)
  mmc: core: eMMC bus width may not work on all platforms
  mmc: sdhci: Auto-CMD23 fixes.
  mmc: sdhci: Auto-CMD23 support.
  mmc: core: Block CMD23 support for UHS104/SDXC cards.
  mmc: sdhci: Implement MMC_CAP_CMD23 for SDHCI.
  mmc: core: Use CMD23 for multiblock transfers when we can.
  mmc: quirks: Add/remove quirks conditional support.
  mmc: Add new VUB300 USB-to-SD/SDIO/MMC driver
  mmc: sdhci-pxa: Add quirks for DMA/ADMA to match h/w
  mmc: core: duplicated trial with same freq in mmc_rescan_try_freq()
  mmc: core: add support for eMMC Dual Data Rate
  mmc: core: eMMC signal voltage does not use CMD11
  mmc: sdhci-pxa: add platform code for UHS signaling
  mmc: sdhci: add hooks for setting UHS in platform specific code
  mmc: core: clear MMC_PM_KEEP_POWER flag on resume
  mmc: dw_mmc: fixed wrong regulator_enable in suspend/resume
  mmc: sdhi: allow powering down controller with no card inserted
  mmc: tmio: runtime suspend the controller, where possible
  mmc: sdhi: support up to 3 interrupt sources
  mmc: sdhi: print physical base address and clock rate
  ...
2011-05-25 16:55:55 -07:00