Pull networking updates from David Miller:
1) Allow setting bluetooth L2CAP modes via socket option, from Luiz
Augusto von Dentz.
2) Add GSO partial support to igc, from Sasha Neftin.
3) Several cleanups and improvements to r8169 from Heiner Kallweit.
4) Add IF_OPER_TESTING link state and use it when ethtool triggers a
device self-test. From Andrew Lunn.
5) Start moving away from custom driver versions, use the globally
defined kernel version instead, from Leon Romanovsky.
6) Support GRO vis gro_cells in DSA layer, from Alexander Lobakin.
7) Allow hard IRQ deferral during NAPI, from Eric Dumazet.
8) Add sriov and vf support to hinic, from Luo bin.
9) Support Media Redundancy Protocol (MRP) in the bridging code, from
Horatiu Vultur.
10) Support netmap in the nft_nat code, from Pablo Neira Ayuso.
11) Allow UDPv6 encapsulation of ESP in the ipsec code, from Sabrina
Dubroca. Also add ipv6 support for espintcp.
12) Lots of ReST conversions of the networking documentation, from Mauro
Carvalho Chehab.
13) Support configuration of ethtool rxnfc flows in bcmgenet driver,
from Doug Berger.
14) Allow to dump cgroup id and filter by it in inet_diag code, from
Dmitry Yakunin.
15) Add infrastructure to export netlink attribute policies to
userspace, from Johannes Berg.
16) Several optimizations to sch_fq scheduler, from Eric Dumazet.
17) Fallback to the default qdisc if qdisc init fails because otherwise
a packet scheduler init failure will make a device inoperative. From
Jesper Dangaard Brouer.
18) Several RISCV bpf jit optimizations, from Luke Nelson.
19) Correct the return type of the ->ndo_start_xmit() method in several
drivers, it's netdev_tx_t but many drivers were using
'int'. From Yunjian Wang.
20) Add an ethtool interface for PHY master/slave config, from Oleksij
Rempel.
21) Add BPF iterators, from Yonghang Song.
22) Add cable test infrastructure, including ethool interfaces, from
Andrew Lunn. Marvell PHY driver is the first to support this
facility.
23) Remove zero-length arrays all over, from Gustavo A. R. Silva.
24) Calculate and maintain an explicit frame size in XDP, from Jesper
Dangaard Brouer.
25) Add CAP_BPF, from Alexei Starovoitov.
26) Support terse dumps in the packet scheduler, from Vlad Buslov.
27) Support XDP_TX bulking in dpaa2 driver, from Ioana Ciornei.
28) Add devm_register_netdev(), from Bartosz Golaszewski.
29) Minimize qdisc resets, from Cong Wang.
30) Get rid of kernel_getsockopt and kernel_setsockopt in order to
eliminate set_fs/get_fs calls. From Christoph Hellwig.
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (2517 commits)
selftests: net: ip_defrag: ignore EPERM
net_failover: fixed rollback in net_failover_open()
Revert "tipc: Fix potential tipc_aead refcnt leak in tipc_crypto_rcv"
Revert "tipc: Fix potential tipc_node refcnt leak in tipc_rcv"
vmxnet3: allow rx flow hash ops only when rss is enabled
hinic: add set_channels ethtool_ops support
selftests/bpf: Add a default $(CXX) value
tools/bpf: Don't use $(COMPILE.c)
bpf, selftests: Use bpf_probe_read_kernel
s390/bpf: Use bcr 0,%0 as tail call nop filler
s390/bpf: Maintain 8-byte stack alignment
selftests/bpf: Fix verifier test
selftests/bpf: Fix sample_cnt shared between two threads
bpf, selftests: Adapt cls_redirect to call csum_level helper
bpf: Add csum_level helper for fixing up csum levels
bpf: Fix up bpf_skb_adjust_room helper's skb csum setting
sfc: add missing annotation for efx_ef10_try_update_nic_stats_vf()
crypto/chtls: IPv6 support for inline TLS
Crypto/chcr: Fixes a coccinile check error
Crypto/chcr: Fixes compilations warnings
...
There was a lockdep which led to commit
fad003b6c8 ("Bluetooth: Fix inconsistent lock state with RFCOMM")
Lockdep noticed that `sk->sk_lock.slock' was acquired without disabling
the softirq while the lock was also used in softirq context.
Unfortunately the solution back then was to disable interrupts before
acquiring the lock which however made lockdep happy.
It would have been enough to simply disable the softirq. Disabling
interrupts before acquiring a spinlock_t is not allowed on PREEMPT_RT
because these locks are converted to 'sleeping' spinlocks.
Use spin_lock_bh() in order to acquire the `sk_lock.slock'.
Reported-by: Luis Claudio R. Goncalves <lclaudio@uudg.org>
Reported-by: kbuild test robot <lkp@intel.com> [missing unlock]
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
EIR flags should just hint if SSP may be supported but we shall verify
this with use of the actual features as the SSP bits may be disabled in
the lower layers which would result in legacy authentication to be
used.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This makes hci_encrypt_cfm calls hci_connect_cfm in case the connection
state is BT_CONFIG so callers don't have to check the state.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Bluetooth PTS test case HFP/AG/ACC/BI-12-I accepts SCO connection
with invalid parameter at the first SCO request expecting AG to
attempt another SCO request with the use of "safe settings" for
given codec, base on section 5.7.1.2 of HFP 1.7 specification.
This patch addresses it by adding "Invalid LMP Parameters" (0x1e)
to the SCO fallback case. Verified with below log:
< HCI Command: Setup Synchronous Connection (0x01|0x0028) plen 17
Handle: 256
Transmit bandwidth: 8000
Receive bandwidth: 8000
Max latency: 13
Setting: 0x0003
Input Coding: Linear
Input Data Format: 1's complement
Input Sample Size: 8-bit
# of bits padding at MSB: 0
Air Coding Format: Transparent Data
Retransmission effort: Optimize for link quality (0x02)
Packet type: 0x0380
3-EV3 may not be used
2-EV5 may not be used
3-EV5 may not be used
> HCI Event: Command Status (0x0f) plen 4
Setup Synchronous Connection (0x01|0x0028) ncmd 1
Status: Success (0x00)
> HCI Event: Number of Completed Packets (0x13) plen 5
Num handles: 1
Handle: 256
Count: 1
> HCI Event: Max Slots Change (0x1b) plen 3
Handle: 256
Max slots: 1
> HCI Event: Synchronous Connect Complete (0x2c) plen 17
Status: Invalid LMP Parameters / Invalid LL Parameters (0x1e)
Handle: 0
Address: 00:1B:DC:F2:21:59 (OUI 00-1B-DC)
Link type: eSCO (0x02)
Transmission interval: 0x00
Retransmission window: 0x02
RX packet length: 0
TX packet length: 0
Air mode: Transparent (0x03)
< HCI Command: Setup Synchronous Connection (0x01|0x0028) plen 17
Handle: 256
Transmit bandwidth: 8000
Receive bandwidth: 8000
Max latency: 8
Setting: 0x0003
Input Coding: Linear
Input Data Format: 1's complement
Input Sample Size: 8-bit
# of bits padding at MSB: 0
Air Coding Format: Transparent Data
Retransmission effort: Optimize for link quality (0x02)
Packet type: 0x03c8
EV3 may be used
2-EV3 may not be used
3-EV3 may not be used
2-EV5 may not be used
3-EV5 may not be used
> HCI Event: Command Status (0x0f) plen 4
Setup Synchronous Connection (0x01|0x0028) ncmd 1
Status: Success (0x00)
> HCI Event: Max Slots Change (0x1b) plen 3
Handle: 256
Max slots: 5
> HCI Event: Max Slots Change (0x1b) plen 3
Handle: 256
Max slots: 1
> HCI Event: Synchronous Connect Complete (0x2c) plen 17
Status: Success (0x00)
Handle: 257
Address: 00:1B:DC:F2:21:59 (OUI 00-1B-DC)
Link type: eSCO (0x02)
Transmission interval: 0x06
Retransmission window: 0x04
RX packet length: 30
TX packet length: 30
Air mode: Transparent (0x03)
Signed-off-by: Hsin-Yu Chao <hychao@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Johan Hedberg says:
====================
pull request: bluetooth-next 2020-05-13
Here's a second attempt at a bluetooth-next pull request which
supercedes the one dated 2020-05-09. This should have the issues
discovered by Jakub fixed.
- Add support for Intel Typhoon Peak device (8087:0032)
- Add device tree bindings for Realtek RTL8723BS device
- Add device tree bindings for Qualcomm QCA9377 device
- Add support for experimental features configuration through mgmt
- Add driver hook to prevent wake from suspend
- Add support for waiting for L2CAP disconnection response
- Multiple fixes & cleanups to the btbcm driver
- Add support for LE scatternet topology for selected devices
- A few other smaller fixes & cleanups
Please let me know if there are any issues pulling. Thanks.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Whenever we disconnect a L2CAP connection, we would immediately
report a disconnection event (EPOLLHUP) to the upper layer, without
waiting for the response of the other device.
This patch offers an option to wait until we receive a disconnection
response before reporting disconnection event, by using the "how"
parameter in l2cap_sock_shutdown(). Therefore, upper layer can opt
to wait for disconnection response by shutdown(sock, SHUT_WR).
This can be used to enforce proper disconnection order in HID,
where the disconnection of the interrupt channel must be complete
before attempting to disconnect the control channel.
Signed-off-by: Archie Pusaka <apusaka@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
After sending Inquiry Cancel command to the controller, it is possible
that Inquiry Complete event comes before Inquiry Cancel command complete
event. In this case the Inquiry Cancel command will have status of
Command Disallowed since there is no Inquiry session to be cancelled.
This case should not be treated as error, otherwise we can reach an
inconsistent state.
Example of a btmon trace when this happened:
< HCI Command: Inquiry Cancel (0x01|0x0002) plen 0
> HCI Event: Inquiry Complete (0x01) plen 1
Status: Success (0x00)
> HCI Event: Command Complete (0x0e) plen 4
Inquiry Cancel (0x01|0x0002) ncmd 1
Status: Command Disallowed (0x0c)
Signed-off-by: Sonny Sasaka <sonnysasaka@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Let drivers have a hook to disable configuring scanning during suspend.
Drivers should use the device_may_wakeup function call to determine
whether hci should be configured for wakeup.
For example, an implementation for btusb may look like the following:
bool btusb_prevent_wake(struct hci_dev *hdev)
{
struct btusb_data *data = hci_get_drvdata(hdev);
return !device_may_wakeup(&data->udev->dev);
}
Signed-off-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
Reviewed-by: Alain Michaud <alainm@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Renamed BT_SUSPEND_COMPLETE to BT_SUSPEND_CONFIGURE_WAKE since it sets
up the event filter and whitelist for wake-up.
Signed-off-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
Reviewed-by: Alain Michaud <alainm@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
When a device is suspended, it doesn't need to be as responsive to
connection events. Increase the interval to 640ms (creating a duty cycle
of roughly 1.75%) so that passive scanning uses much less power (vs
previous duty cycle of 18.75%). The new window + interval combination
has been tested to work with HID devices (which are currently the only
devices capable of wake up).
Signed-off-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The types for window and interval should be uint16, not uint8.
Signed-off-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
In case dynamic debug is disabled, this feature allows a vendor platform
to provide debug statement printing.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
To enable platform specific experimental features, introduce this new set of
management commands and events.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The security manager operates on a specific controller and thus use
bt_dev_dbg to indetify the controller for each debug message.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
When setting HCI_MGMT_HDEV_OPTIONAL it is possible to target a specific
conntroller or a global interface.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The majority of management interaction are based on a controller index
and have a hci_dev associated with it. So use bt_dev_dbg to have a clean
way of indentifying the controller the debug message belongs to.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The event MGMT_EV_PHY_CONFIGURATION_CHANGED wasn't listed in the list of
supported events. So add it.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Fix 2 typos in L2CAP_CREDIT_BASED_CONNECTION_REQ (0x17) handling function, that
cause BlueZ answer with L2CAP_CR_LE_INVALID_PARAMS or L2CAP_CR_LE_INVALID_SCID
error on a correct ECRED connection request.
Enchanced Credit Based Mode support was recently introduced with the commit
15f02b9105 ("Bluetooth: L2CAP: Add initial code
for Enhanced Credit Based Mode").
Signed-off-by: Konstantin Forostyan <konstantin.forostyan@peiker-cee.de>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch fix the advertising handle is set to 0 regardless of actual
instance value. The affected commands are LE Set Advertising Set Random
Address, LE Set Extended Advertising Data, and LE Set Extended Scan
Response Data commands.
Signed-off-by: Tedd Ho-Jeong An <tedd.an@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Instead of manually allocating a 'struct shash_desc' on the stack and
calling crypto_shash_digest(), switch to using the new helper function
crypto_shash_tfm_digest() which does this for us.
Cc: linux-bluetooth@vger.kernel.org
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
This patch reverts the folowing commits:
commit 064ff66e2b
"bonding: add missing netdev_update_lockdep_key()"
commit 53d374979e
"net: avoid updating qdisc_xmit_lock_key in netdev_update_lockdep_key()"
commit 1f26c0d3d2
"net: fix kernel-doc warning in <linux/netdevice.h>"
commit ab92d68fc2
"net: core: add generic lockdep keys"
but keeps the addr_list_lock_key because we still lock
addr_list_lock nestedly on stack devices, unlikely xmit_lock
this is safe because we don't take addr_list_lock on any fast
path.
Reported-and-tested-by: syzbot+aaa6fa4949cc5d9b7b25@syzkaller.appspotmail.com
Cc: Dmitry Vyukov <dvyukov@google.com>
Cc: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Acked-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This change allows scatternet connections to be created if the
controller reports support and the HCI_QUIRK_VALID_LE_STATES indicates
that the reported LE states can be trusted.
Signed-off-by: Alain Michaud <alainm@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The Enhanced Connection Complete event is use in conjunction with LL
Privacy and not Extended Advertising.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
In case LL Privacy is supported by the controller, it is also a good
idea to use the LE Enhanced Connection Complete event for getting all
information about the new connection and its addresses.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
When starting active scanning for discovery the whitelist is not needed
to be used. So the filter_policy is 0x00. To make the core more readable
use a variable name instead of just setting 0 as paramter.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The error could indicate a problem with the Bluetooth device. It
is easier to investigate if the packet's actual length gets logged,
not just the fact that a discrepancy occurred.
Signed-off-by: Daniels Umanovskis <du@axentia.se>
Reviewed-by: Alain Michaud <alainm@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
To improve security, always give the user-space daemon a chance to
accept or reject a Just Works pairing (LE). The daemon may decide to
auto-accept based on the user's intent.
This patch is similar to the previous patch but applies for LE Secure
Connections (SC).
Signed-off-by: Sonny Sasaka <sonnysasaka@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Some static checker run by 0day reports a variableScope warning.
net/bluetooth/smp.c:870:6: warning:
The scope of the variable 'err' can be reduced. [variableScope]
There is no need for two separate variables holding return values.
Stick with the existing variable. While at it, don't pre-initialize
'ret' because it is set in each code path.
tk_request() is supposed to return a negative error code on errors,
not a bluetooth return code. The calling code converts the return
value to SMP_UNSPECIFIED if needed.
Fixes: 92516cd97f ("Bluetooth: Always request for user confirmation for Just Works")
Cc: Sonny Sasaka <sonnysasaka@chromium.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Sonny Sasaka <sonnysasaka@chromium.org>
Signed-off-by: Sonny Sasaka <sonnysasaka@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The BT qualification test SM/MAS/PKE/BV-01-C needs us to turn off
the MITM flag when pairing, and at the same time also set the io
capability to something other than no input no output.
Currently the MITM flag is only unset when the io capability is set
to no input no output, therefore the test cannot be executed.
This patch introduces a debugfs option to force MITM flag to be
turned off.
Signed-off-by: Archie Pusaka <apusaka@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Increment the mgmt revision due to the recently added new commands.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
To allow userspace to make correcty security policy decision, the kernel
needs to export a few details of the supported security features and
encryption key size information. This command exports this information
and also allows future extensions if needed.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Reviewed-by: Alain Michaud <alainm@chromium.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
With the Read Local Simple Pairing Options command it is possible to
retrieve the support for max encryption key size supported by the
controller and also if the controller correctly verifies the ECDH public
key during pairing.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Reviewed-by: Alain Michaud <alainm@chromium.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Micrsoft defined a set for HCI vendor extensions. Check the following
link for details:
https://docs.microsoft.com/en-us/windows-hardware/drivers/bluetooth/microsoft-defined-bluetooth-hci-commands-and-events
This provides the basic framework to enable the extension and read its
supported features. Drivers still have to declare support for this
extension before it can be utilized by the host stack.
Signed-off-by: Miao-chen Chou <mcchou@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
This is just a cosmetic clean to move the selftests configuration option
to the bottom of the list of options.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
notifying using HCI_NOTIFY_CONN_ADD for SCO connection is generic in
case of mSBC audio. To differntiate SCO air mode introducing
HCI_NOTIFY_ENABLE_SCO_CVSD and HCI_NOTIFY_ENABLE_SCO_TRANSP.
Signed-off-by: Sathish Narsimman <sathish.narasimman@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
When scheduling TX packets, send all SCO/eSCO packets first, check for
pending SCO/eSCO packets after every ACL/LE packet and send them if any
are pending. This is done to make sure that we can meet SCO deadlines
on slow interfaces like UART.
If we were to queue up multiple ACL packets without checking for a SCO
packet, we might miss the SCO timing. For example:
The time it takes to send a maximum size ACL packet (1024 bytes):
t = 10/8 * 1024 bytes * 8 bits/byte * 1 packet / baudrate
where 10/8 is uart overhead due to start/stop bits per byte
Replace t = 3.75ms (SCO deadline), which gives us a baudrate of 2730666.
At a baudrate of 3000000, if we didn't check for SCO packets within 1024
bytes, we would miss the 3.75ms timing window.
Signed-off-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
To improve security, always give the user-space daemon a chance to
accept or reject a Just Works pairing (LE). The daemon may decide to
auto-accept based on the user's intent.
Signed-off-by: Sonny Sasaka <sonnysasaka@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This adds BT_MODE socket option which can be used to set L2CAP modes,
including modes only supported over LE which were not supported using
the L2CAP_OPTIONS.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
L2CAP_OPTIONS shall only be used with BR/EDR modes.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This uses the DEFER_SETUP flag to group channels with
L2CAP_CREDIT_BASED_CONNECTION_REQ.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
With this change, the encryption key size is not assumed to be 16 if the
read_encryption_key_size command fails for any reason. This ensures
that if the controller fails the command for any reason that the
encryption key size isn't implicitely set to 16 and instead take a more
concervative posture to assume it is 0.
Signed-off-by: Alain Michaud <alainm@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This adds a callback to read the socket pid.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
When handling auto-connected devices, we should execute the rest of the
connection complete when it was previously discovered and it is an ACL
connection.
Signed-off-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
If Bluetooth fails to enter the suspended state correctly, restore the
state to running (re-enabling scans). PM_POST_SUSPEND is only sent to
notifiers that successfully return from PM_PREPARE_SUSPEND notification
so we should recover gracefully if it fails.
Signed-off-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
BlueZ cancels adv when starting a scan, but does not cancel a scan when
starting to adv. Neither is required, so this brings both to a
consistent state (of not affecting each other). Some very rare (I've
never seen one) BT 4.0 chips will fail to do both at once. Even this is
ok since the command that will fail will be the second one, and thus the
common sense logic of first-come-first-served is preserved for BLE
requests.
Signed-off-by: Dmitry Grinberg <dmitrygr@google.com>
Signed-off-by: Manish Mandlik <mmandlik@google.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
net/bluetooth/l2cap_core.c: In function l2cap_ecred_conn_req:
net/bluetooth/l2cap_core.c:5848:6: warning: variable credits set but not used [-Wunused-but-set-variable]
commit 15f02b9105 ("Bluetooth: L2CAP: Add initial code for Enhanced Credit Based Mode")
involved this unused variable, remove it.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Smatch complains about the indenting:
net/bluetooth/l2cap_sock.c:1027 l2cap_sock_recvmsg()
warn: inconsistent indenting
It looks like this is supposed to be an "else if" condition.
Fixes: 15f02b9105 ("Bluetooth: L2CAP: Add initial code for Enhanced Credit Based Mode")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Linus Torvalds
Sebastian Andrzej Siewior
Luiz Augusto von Dentz
Hsin-Yu Chao
Łukasz Rymanowski
David S. Miller
Archie Pusaka
Sonny Sasaka
Abhishek Pandit-Subedi
Marcel Holtmann
Konstantin Forostyan
Tedd Ho-Jeong An
Eric Biggers
Cong Wang
Alain Michaud
Daniels Umanovskis
Guenter Roeck
Miao-chen Chou
Sathish Narsimman
Sonny Sasaka
Dmitry Grinberg
YueHaibing
Dan Carpenter