In commit c55c8edafa ("tipc: smooth change between replicast and
broadcast"), we allow instant switching between replicast and broadcast
by sending a dummy 'SYN' packet on the last used link to synchronize
packets on the links. The 'SYN' message is an object of link congestion
also, so if that happens, a 'SOCK_WAKEUP' will be scheduled to be sent
back to the socket...
However, in that commit, we simply use the same socket 'cong_link_cnt'
counter for both the 'SYN' & normal payload message sending. Therefore,
if both the replicast & broadcast links are congested, the counter will
be not updated correctly but overwritten by the latter congestion.
Later on, when the 'SOCK_WAKEUP' messages are processed, the counter is
reduced one by one and eventually overflowed. Consequently, further
activities on the socket will only wait for the false congestion signal
to disappear but never been met.
Because sending the 'SYN' message is vital for the mechanism, it should
be done anyway. This commit fixes the issue by marking the message with
an error code e.g. 'TIPC_ERR_NO_PORT', so its sending should not face a
link congestion, there is no need to touch the socket 'cong_link_cnt'
either. In addition, in the event of any error (e.g. -ENOBUFS), we will
purge the entire payload message queue and make a return immediately.
Fixes: c55c8edafa ("tipc: smooth change between replicast and broadcast")
Acked-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: Tuong Lien <tuong.t.lien@dektech.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current rbtree for service ranges in the name table is built based
on the 'lower' & 'upper' range values resulting in a flaw in the rbtree
searching. Some issues have been observed in case of range overlapping:
Case #1: unable to withdraw a name entry:
After some name services are bound, all of them are withdrawn by user
but one remains in the name table forever. This corrupts the table and
that service becomes dummy i.e. no real port.
E.g.
/
{22, 22}
/
/
---> {10, 50}
/ \
/ \
{10, 30} {20, 60}
The node {10, 30} cannot be removed since the rbtree searching stops at
the node's ancestor i.e. {10, 50}, so starting from it will never reach
the finding node.
Case #2: failed to send data in some cases:
E.g. Two service ranges: {20, 60}, {10, 50} are bound. The rbtree for
this service will be one of the two cases below depending on the order
of the bindings:
{20, 60} {10, 50} <--
/ \ / \
/ \ / \
{10, 50} NIL <-- NIL {20, 60}
(a) (b)
Now, try to send some data to service {30}, there will be two results:
(a): Failed, no route to host.
(b): Ok.
The reason is that the rbtree searching will stop at the pointing node
as shown above.
Case #3: Same as case #2b above but if the data sending's scope is
local and the {10, 50} is published by a peer node, then it will result
in 'no route to host' even though the other {20, 60} is for example on
the local node which should be able to get the data.
The issues are actually due to the way we built the rbtree. This commit
fixes it by introducing an additional field to each node - named 'max',
which is the largest 'upper' of that node subtree. The 'max' value for
each subtrees will be propagated correctly whenever a node is inserted/
removed or the tree is rebalanced by the augmented rbtree callbacks.
By this way, we can change the rbtree searching appoarch to solve the
issues above. Another benefit from this is that we can now improve the
searching for a next range matching e.g. in case of multicast, so get
rid of the unneeded looping over all nodes in the tree.
Acked-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: Tuong Lien <tuong.t.lien@dektech.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
We introduce a simple variable window congestion control for links.
The algorithm is inspired by the Reno algorithm, covering both 'slow
start', 'congestion avoidance', and 'fast recovery' modes.
- We introduce hard lower and upper window limits per link, still
different and configurable per bearer type.
- We introduce a 'slow start theshold' variable, initially set to
the maximum window size.
- We let a link start at the minimum congestion window, i.e. in slow
start mode, and then let is grow rapidly (+1 per rceived ACK) until
it reaches the slow start threshold and enters congestion avoidance
mode.
- In congestion avoidance mode we increment the congestion window for
each window-size number of acked packets, up to a possible maximum
equal to the configured maximum window.
- For each non-duplicate NACK received, we drop back to fast recovery
mode, by setting the both the slow start threshold to and the
congestion window to (current_congestion_window / 2).
- If the timeout handler finds that the transmit queue has not moved
since the previous timeout, it drops the link back to slow start
and forces a probe containing the last sent sequence number to the
sent to the peer, so that this can discover the stale situation.
This change does in reality have effect only on unicast ethernet
transport, as we have seen that there is no room whatsoever for
increasing the window max size for the UDP bearer.
For now, we also choose to keep the limits for the broadcast link
unchanged and equal.
This algorithm seems to give a 50-100% throughput improvement for
messages larger than MTU.
Suggested-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When we increase the link tranmsit window we often observe the following
scenario:
1) A STATE message bypasses a sequence of traffic packets and arrives
far ahead of those to the receiver. STATE messages contain a
'peers_nxt_snt' field to indicate which was the last packet sent
from the peer. This mechanism is intended as a last resort for the
receiver to detect missing packets, e.g., during very low traffic
when there is no packet flow to help early loss detection.
3) The receiving link compares the 'peer_nxt_snt' field to its own
'rcv_nxt', finds that there is a gap, and immediately sends a
NACK message back to the peer.
4) When this NACKs arrives at the sender, all the requested
retransmissions are performed, since it is a first-time request.
Just like in the scenario described in the previous commit this leads
to many redundant retransmissions, with decreased throughput as a
consequence.
We fix this by adding two more conditions before we send a NACK in
this sitution. First, the deferred queue must be empty, so we cannot
assume that the potential packet loss has already been detected by
other means. Second, we check the 'peers_snd_nxt' field only in probe/
probe_reply messages, thus turning this into a true mechanism of last
resort as it was really meant to be.
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When we increase the link send window we sometimes observe the
following scenario:
1) A packet #N arrives out of order far ahead of a sequence of older
packets which are still under way. The packet is added to the
deferred queue.
2) The missing packets arrive in sequence, and for each 16th of them
an ACK is sent back to the receiver, as it should be.
3) When building those ACK messages, it is checked if there is a gap
between the link's 'rcv_nxt' and the first packet in the deferred
queue. This is always the case until packet number #N-1 arrives, and
a 'gap' indicator is added, effectively turning them into NACK
messages.
4) When those NACKs arrive at the sender, all the requested
retransmissions are done, since it is a first-time request.
This sometimes leads to a huge amount of redundant retransmissions,
causing a drop in max throughput. This problem gets worse when we
in a later commit introduce variable window congestion control,
since it drops the link back to 'fast recovery' much more often
than necessary.
We now fix this by not sending any 'gap' indicator in regular ACK
messages. We already have a mechanism for sending explicit NACKs
in place, and this is sufficient to keep up the packet flow.
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ipv6_stub uses the ip6_dst_lookup function to allow other modules to
perform IPv6 lookups. However, this function skips the XFRM layer
entirely.
All users of ipv6_stub->ip6_dst_lookup use ip_route_output_flow (via the
ip_route_output_key and ip_route_output helpers) for their IPv4 lookups,
which calls xfrm_lookup_route(). This patch fixes this inconsistent
behavior by switching the stub to ip6_dst_lookup_flow, which also calls
xfrm_lookup_route().
This requires some changes in all the callers, as these two functions
take different arguments and have different return types.
Fixes: 5f81bd2e5d ("ipv6: export a stub for IPv6 symbols used by vxlan")
Reported-by: Xiumei Mu <xmu@redhat.com>
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Scenario:
1. A client socket initiates a SYN message to a listening socket.
2. The send link is congested, the SYN message is put in the
send link and a wakeup message is put in wakeup queue.
3. The congestion situation is abated, the wakeup message is
pulled out of the wakeup queue. Function tipc_sk_push_backlog()
is called to send out delayed messages by Nagle. However,
the client socket is still in CONNECTING state. So, it sends
the SYN message in the socket write queue to the listening socket
again.
4. The listening socket receives the first SYN message and creates
first server socket. The client socket receives ACK- and establishes
a connection to the first server socket. The client socket closes
its connection with the first server socket.
5. The listening socket receives the second SYN message and creates
second server socket. The second server socket sends ACK- to the
client socket, but it has been closed. It results in connection
reset error when reading from the server socket in user space.
Solution: return from function tipc_sk_push_backlog() immediately
if there is pending SYN message in the socket write queue.
Fixes: c0bceb97db ("tipc: add smart nagle feature")
Signed-off-by: Tung Nguyen <tung.q.nguyen@dektech.com.au>
Acked-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In function __tipc_shutdown(), the timeout value passed to
tipc_wait_for_cond() is not jiffies.
This commit fixes it by converting that value from milliseconds
to jiffies.
Fixes: 365ad353c2 ("tipc: reduce risk of user starvation during link congestion")
Signed-off-by: Tung Nguyen <tung.q.nguyen@dektech.com.au>
Acked-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When tipc_sk_timeout() is executed but user space is grabbing
ownership, this function rearms itself and returns. However, the
socket reference counter is not reduced. This causes potential
unexpected behavior.
This commit fixes it by calling sock_put() before tipc_sk_timeout()
returns in the above-mentioned case.
Fixes: afe8792fec ("tipc: refactor function tipc_sk_timeout()")
Signed-off-by: Tung Nguyen <tung.q.nguyen@dektech.com.au>
Acked-by: Ying Xue <ying.xue@windriver.com>
Acked-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When initiating a connection message to a server side, the connection
message is cloned and added to the socket write queue. However, if the
cloning is failed, only the socket write queue is purged. It causes
memory leak because the original connection message is not freed.
This commit fixes it by purging the list of connection message when
it cannot be cloned.
Fixes: 6787927475 ("tipc: buffer overflow handling in listener socket")
Reported-by: Hoang Le <hoang.h.le@dektech.com.au>
Signed-off-by: Tung Nguyen <tung.q.nguyen@dektech.com.au>
Acked-by: Ying Xue <ying.xue@windriver.com>
Acked-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In commit 4f07b80c97 ("tipc: check msg->req data len in
tipc_nl_compat_bearer_disable") the same patch code was copied into
routines: tipc_nl_compat_bearer_disable(),
tipc_nl_compat_link_stat_dump() and tipc_nl_compat_link_reset_stats().
The two link routine occurrences should have been modified to check
the maximum link name length and not bearer name length.
Fixes: 4f07b80c97 ("tipc: check msg->reg data len in tipc_nl_compat_bearer_disable")
Signed-off-by: John Rutherford <john.rutherford@dektech.com.au>
Acked-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
rhashtable_lookup_fast() internally calls rcu_read_lock() then,
calls rhashtable_lookup(). So if rcu_read_lock() is already held,
rhashtable_lookup() is enough.
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
It is observed that TIPC service binding order will not be kept in the
publication event report to user if the service is subscribed after the
bindings.
For example, services are bound by application in the following order:
Server: bound port A to {18888,66,66} scope 2
Server: bound port A to {18888,33,33} scope 2
Now, if a client subscribes to the service range (e.g. {18888, 0-100}),
it will get the 'TIPC_PUBLISHED' events in that binding order only when
the subscription is started before the bindings.
Otherwise, if started after the bindings, the events will arrive in the
opposite order:
Client: received event for published {18888,33,33}
Client: received event for published {18888,66,66}
For the latter case, it is clear that the bindings have existed in the
name table already, so when reported, the events' order will follow the
order of the rbtree binding nodes (- a node with lesser 'lower'/'upper'
range value will be first).
This is correct as we provide the tracking on a specific service status
(available or not), not the relationship between multiple services.
However, some users expect to see the same order of arriving events
irrespective of when the subscription is issued. This turns out to be
easy to fix. We now add functionality to ensure that publication events
always are issued in the same temporal order as the corresponding
bindings were performed.
v2: replace the unnecessary macro - 'publication_after()' with inline
function.
v3: reuse 'time_after32()' instead of reinventing the same exact code.
Acked-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: Tuong Lien <tuong.t.lien@dektech.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
When setting up a cluster with non-replicast/replicast capability
supported. This capability will be disabled for broadcast send link
in order to be backwards compatible.
However, when these non-support nodes left and be removed out the cluster.
We don't update this capability on broadcast send link. Then, some of
features that based on this capability will also disabling as unexpected.
In this commit, we make sure the broadcast send link capabilities will
be re-calculated as soon as a node removed/rejoined a cluster.
Acked-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: Hoang Le <hoang.h.le@dektech.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
The tipc prefix for log messages generated by tipc was
removed in commit 07f6c4bc04 ("tipc: convert tipc reference
table to use generic rhashtable").
This is still a useful prefix so add it back.
Signed-off-by: Matt Bennett <matt.bennett@alliedtelesis.co.nz>
Acked-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In commit 25b0b9c4e8 ("tipc: handle collisions of 32-bit node address
hash values"), the 32-bit node address only generated after one second
trial period expired. However the self's addr in struct tipc_monitor do
not update according to node address generated. This lead to it is
always zero as initial value. As result, sorting algorithm using this
value does not work as expected, neither neighbor monitoring framework.
In this commit, we add a fix to update self's addr when 32-bit node
address generated.
Fixes: 25b0b9c4e8 ("tipc: handle collisions of 32-bit node address hash values")
Acked-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: Hoang Le <hoang.h.le@dektech.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Variable err is not uninitialized and hence can potentially contain
any garbage value. This may cause an error when logical or'ing the
return values from the calls to functions crypto_aead_setauthsize or
crypto_aead_setkey. Fix this by setting err to the return of
crypto_aead_setauthsize rather than or'ing in the return into the
uninitialized variable
Addresses-Coverity: ("Uninitialized scalar variable")
Fixes: fc1b6d6de2 ("tipc: introduce TIPC encryption & authentication")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This commit adds two netlink commands to TIPC in order for user to be
able to set or remove AEAD keys:
- TIPC_NL_KEY_SET
- TIPC_NL_KEY_FLUSH
When the 'KEY_SET' is given along with the key data, the key will be
initiated and attached to TIPC crypto. On the other hand, the
'KEY_FLUSH' command will remove all existing keys if any.
Acked-by: Ying Xue <ying.xue@windreiver.com>
Acked-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: Tuong Lien <tuong.t.lien@dektech.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
This commit offers an option to encrypt and authenticate all messaging,
including the neighbor discovery messages. The currently most advanced
algorithm supported is the AEAD AES-GCM (like IPSec or TLS). All
encryption/decryption is done at the bearer layer, just before leaving
or after entering TIPC.
Supported features:
- Encryption & authentication of all TIPC messages (header + data);
- Two symmetric-key modes: Cluster and Per-node;
- Automatic key switching;
- Key-expired revoking (sequence number wrapped);
- Lock-free encryption/decryption (RCU);
- Asynchronous crypto, Intel AES-NI supported;
- Multiple cipher transforms;
- Logs & statistics;
Two key modes:
- Cluster key mode: One single key is used for both TX & RX in all
nodes in the cluster.
- Per-node key mode: Each nodes in the cluster has one specific TX key.
For RX, a node requires its peers' TX key to be able to decrypt the
messages from those peers.
Key setting from user-space is performed via netlink by a user program
(e.g. the iproute2 'tipc' tool).
Internal key state machine:
Attach Align(RX)
+-+ +-+
| V | V
+---------+ Attach +---------+
| IDLE |---------------->| PENDING |(user = 0)
+---------+ +---------+
A A Switch| A
| | | |
| | Free(switch/revoked) | |
(Free)| +----------------------+ | |Timeout
| (TX) | | |(RX)
| | | |
| | v |
+---------+ Switch +---------+
| PASSIVE |<----------------| ACTIVE |
+---------+ (RX) +---------+
(user = 1) (user >= 1)
The number of TFMs is 10 by default and can be changed via the procfs
'net/tipc/max_tfms'. At this moment, as for simplicity, this file is
also used to print the crypto statistics at runtime:
echo 0xfff1 > /proc/sys/net/tipc/max_tfms
The patch defines a new TIPC version (v7) for the encryption message (-
backward compatibility as well). The message is basically encapsulated
as follows:
+----------------------------------------------------------+
| TIPCv7 encryption | Original TIPCv2 | Authentication |
| header | packet (encrypted) | Tag |
+----------------------------------------------------------+
The throughput is about ~40% for small messages (compared with non-
encryption) and ~9% for large messages. With the support from hardware
crypto i.e. the Intel AES-NI CPU instructions, the throughput increases
upto ~85% for small messages and ~55% for large messages.
By default, the new feature is inactive (i.e. no encryption) until user
sets a key for TIPC. There is however also a new option - "TIPC_CRYPTO"
in the kernel configuration to enable/disable the new code when needed.
MAINTAINERS | add two new files 'crypto.h' & 'crypto.c' in tipc
Acked-by: Ying Xue <ying.xue@windreiver.com>
Acked-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: Tuong Lien <tuong.t.lien@dektech.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
When user sets RX key for a peer not existing on the own node, a new
node entry is needed to which the RX key will be attached. However,
since the peer node address (& capabilities) is unknown at that moment,
only the node-ID is provided, this commit allows the creation of a node
with only the data that we call as “preliminary”.
A preliminary node is not the object of the “tipc_node_find()” but the
“tipc_node_find_by_id()”. Once the first message i.e. LINK_CONFIG comes
from that peer, and is successfully decrypted by the own node, the
actual peer node data will be properly updated and the node will
function as usual.
In addition, the node timer always starts when a node object is created
so if a preliminary node is not used, it will be cleaned up.
The later encryption functions will also use the node timer and be able
to create a preliminary node automatically when needed.
Acked-by: Ying Xue <ying.xue@windreiver.com>
Acked-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: Tuong Lien <tuong.t.lien@dektech.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
As a need to support the crypto asynchronous operations in the later
commits, apart from the current RCU mechanism for bearer pointer, we
add a 'refcnt' to the bearer object as well.
So, a bearer can be hold via 'tipc_bearer_hold()' without being freed
even though the bearer or interface can be disabled in the meanwhile.
If that happens, the bearer will be released then when the crypto
operation is completed and 'tipc_bearer_put()' is called.
Acked-by: Ying Xue <ying.xue@windreiver.com>
Acked-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: Tuong Lien <tuong.t.lien@dektech.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, we scan over all network namespaces at each received
discovery message in order to check if the sending peer might be
present in a host local namespaces.
This is unnecessary since we can assume that a peer will not change its
location during an established session.
We now improve the condition for this testing so that we don't perform
any redundant scans.
Fixes: f73b12812a ("tipc: improve throughput between nodes in netns")
Acked-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: Hoang Le <hoang.h.le@dektech.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
When preparing tunnel packets for the link failover or synchronization,
as for the safe algorithm, we added a dummy packet on the pair link but
never sent it out. In the case of failover, the pair link will be reset
anyway. But for link synching, it will always result in retransmission
of the dummy packet after that.
We have also observed that such the retransmission at the early stage
when a new node comes in a large cluster will take some time and hard
to be done, leading to the repeated retransmit failures and the link is
reset.
Since in commit 4929a932be ("tipc: optimize link synching mechanism")
we have already built a dummy 'TUNNEL_PROTOCOL' message on the new link
for the synchronization, there's no need for the dummy on the pair one,
this commit will skip it when the new mechanism takes in place. In case
nothing exists in the pair link's transmq, the link synching will just
start and stop shortly on the peer side.
The patch is backward compatible.
Acked-by: Jon Maloy <jon.maloy@ericsson.com>
Tested-by: Hoang Le <hoang.h.le@dektech.com.au>
Signed-off-by: Tuong Lien <tuong.t.lien@dektech.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
With huge cluster (e.g >200nodes), the amount of that flow:
gap -> retransmit packet -> acked will take time in case of STATE_MSG
dropped/delayed because a lot of traffic. This lead to 1.5 sec tolerance
value criteria made link easy failure around 2nd, 3rd of failed
retransmission attempts.
Instead of re-introduced criteria of 99 faled retransmissions to fix the
issue, we increase failure detection timer to ten times tolerance value.
Fixes: 77cf8edbc0 ("tipc: simplify stale link failure criteria")
Acked-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: Hoang Le <hoang.h.le@dektech.com.au>
Acked-by: Jon
Signed-off-by: David S. Miller <davem@davemloft.net>
There are two improvements when re-calculate cluster capabilities:
- When deleting a specific down node, need to re-calculate.
- In tipc_node_cleanup(), do not need to re-calculate if node
is still existing in cluster.
Acked-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: Hoang Le <hoang.h.le@dektech.com.au>
Acked-by: Jon
Signed-off-by: David S. Miller <davem@davemloft.net>
As mentioned in commit e95584a889 ("tipc: fix unlimited bundling of
small messages"), the current message bundling algorithm is inefficient
that can generate bundles of only one payload message, that causes
unnecessary overheads for both the sender and receiver.
This commit re-designs the 'tipc_msg_make_bundle()' function (now named
as 'tipc_msg_try_bundle()'), so that when a message comes at the first
place, we will just check & keep a reference to it if the message is
suitable for bundling. The message buffer will be put into the link
backlog queue and processed as normal. Later on, when another one comes
we will make a bundle with the first message if possible and so on...
This way, a bundle if really needed will always consist of at least two
payload messages. Otherwise, we let the first buffer go its way without
any need of bundling, so reduce the overheads to zero.
Moreover, since now we have both the messages in hand, we can even
optimize the 'tipc_msg_bundle()' function, make bundle of a very large
(size ~ MSS) and small messages which is not with the current algorithm
e.g. [1400-byte message] + [10-byte message] (MTU = 1500).
Acked-by: Ying Xue <ying.xue@windreiver.com>
Acked-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: Tuong Lien <tuong.t.lien@dektech.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
The only slightly tricky merge conflict was the netdevsim because the
mutex locking fix overlapped a lot of driver reload reorganization.
The rest were (relatively) trivial in nature.
Signed-off-by: David S. Miller <davem@davemloft.net>
We introduce a feature that works like a combination of TCP_NAGLE and
TCP_CORK, but without some of the weaknesses of those. In particular,
we will not observe long delivery delays because of delayed acks, since
the algorithm itself decides if and when acks are to be sent from the
receiving peer.
- The nagle property as such is determined by manipulating a new
'maxnagle' field in struct tipc_sock. If certain conditions are met,
'maxnagle' will define max size of the messages which can be bundled.
If it is set to zero no messages are ever bundled, implying that the
nagle property is disabled.
- A socket with the nagle property enabled enters nagle mode when more
than 4 messages have been sent out without receiving any data message
from the peer.
- A socket leaves nagle mode whenever it receives a data message from
the peer.
In nagle mode, messages smaller than 'maxnagle' are accumulated in the
socket write queue. The last buffer in the queue is marked with a new
'ack_required' bit, which forces the receiving peer to send a CONN_ACK
message back to the sender upon reception.
The accumulated contents of the write queue is transmitted when one of
the following events or conditions occur.
- A CONN_ACK message is received from the peer.
- A data message is received from the peer.
- A SOCK_WAKEUP pseudo message is received from the link level.
- The write queue contains more than 64 1k blocks of data.
- The connection is being shut down.
- There is no CONN_ACK message to expect. I.e., there is currently
no outstanding message where the 'ack_required' bit was set. As a
consequence, the first message added after we enter nagle mode
is always sent directly with this bit set.
This new feature gives a 50-100% improvement of throughput for small
(i.e., less than MTU size) messages, while it might add up to one RTT
to latency time when the socket is in nagle mode.
Acked-by: Ying Xue <ying.xue@windreiver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, TIPC transports intra-node user data messages directly
socket to socket, hence shortcutting all the lower layers of the
communication stack. This gives TIPC very good intra node performance,
both regarding throughput and latency.
We now introduce a similar mechanism for TIPC data traffic across
network namespaces located in the same kernel. On the send path, the
call chain is as always accompanied by the sending node's network name
space pointer. However, once we have reliably established that the
receiving node is represented by a namespace on the same host, we just
replace the namespace pointer with the receiving node/namespace's
ditto, and follow the regular socket receive patch though the receiving
node. This technique gives us a throughput similar to the node internal
throughput, several times larger than if we let the traffic go though
the full network stacks. As a comparison, max throughput for 64k
messages is four times larger than TCP throughput for the same type of
traffic.
To meet any security concerns, the following should be noted.
- All nodes joining a cluster are supposed to have been be certified
and authenticated by mechanisms outside TIPC. This is no different for
nodes/namespaces on the same host; they have to auto discover each
other using the attached interfaces, and establish links which are
supervised via the regular link monitoring mechanism. Hence, a kernel
local node has no other way to join a cluster than any other node, and
have to obey to policies set in the IP or device layers of the stack.
- Only when a sender has established with 100% certainty that the peer
node is located in a kernel local namespace does it choose to let user
data messages, and only those, take the crossover path to the receiving
node/namespace.
- If the receiving node/namespace is removed, its namespace pointer
is invalidated at all peer nodes, and their neighbor link monitoring
will eventually note that this node is gone.
- To ensure the "100% certainty" criteria, and prevent any possible
spoofing, received discovery messages must contain a proof that the
sender knows a common secret. We use the hash mix of the sending
node/namespace for this purpose, since it can be accessed directly by
all other namespaces in the kernel. Upon reception of a discovery
message, the receiver checks this proof against all the local
namespaces'hash_mix:es. If it finds a match, that, along with a
matching node id and cluster id, this is deemed sufficient proof that
the peer node in question is in a local namespace, and a wormhole can
be opened.
- We should also consider that TIPC is intended to be a cluster local
IPC mechanism (just like e.g. UNIX sockets) rather than a network
protocol, and hence we think it can justified to allow it to shortcut the
lower protocol layers.
Regarding traceability, we should notice that since commit 6c9081a391
("tipc: add loopback device tracking") it is possible to follow the node
internal packet flow by just activating tcpdump on the loopback
interface. This will be true even for this mechanism; by activating
tcpdump on the involved nodes' loopback interfaces their inter-name
space messaging can easily be tracked.
v2:
- update 'net' pointer when node left/rejoined
v3:
- grab read/write lock when using node ref obj
v4:
- clone traffics between netns to loopback
Suggested-by: Jon Maloy <jon.maloy@ericsson.com>
Acked-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: Hoang Le <hoang.h.le@dektech.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Many poll() handlers are lockless. Using skb_queue_empty_lockless()
instead of skb_queue_empty() is more appropriate.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
sk->sk_backlog.len can be written by BH handlers, and read
from process contexts in a lockless way.
Note the write side should also use WRITE_ONCE() or a variant.
We need some agreement about the best way to do this.
syzbot reported :
BUG: KCSAN: data-race in tcp_add_backlog / tcp_grow_window.isra.0
write to 0xffff88812665f32c of 4 bytes by interrupt on cpu 1:
sk_add_backlog include/net/sock.h:934 [inline]
tcp_add_backlog+0x4a0/0xcc0 net/ipv4/tcp_ipv4.c:1737
tcp_v4_rcv+0x1aba/0x1bf0 net/ipv4/tcp_ipv4.c:1925
ip_protocol_deliver_rcu+0x51/0x470 net/ipv4/ip_input.c:204
ip_local_deliver_finish+0x110/0x140 net/ipv4/ip_input.c:231
NF_HOOK include/linux/netfilter.h:305 [inline]
NF_HOOK include/linux/netfilter.h:299 [inline]
ip_local_deliver+0x133/0x210 net/ipv4/ip_input.c:252
dst_input include/net/dst.h:442 [inline]
ip_rcv_finish+0x121/0x160 net/ipv4/ip_input.c:413
NF_HOOK include/linux/netfilter.h:305 [inline]
NF_HOOK include/linux/netfilter.h:299 [inline]
ip_rcv+0x18f/0x1a0 net/ipv4/ip_input.c:523
__netif_receive_skb_one_core+0xa7/0xe0 net/core/dev.c:5004
__netif_receive_skb+0x37/0xf0 net/core/dev.c:5118
netif_receive_skb_internal+0x59/0x190 net/core/dev.c:5208
napi_skb_finish net/core/dev.c:5671 [inline]
napi_gro_receive+0x28f/0x330 net/core/dev.c:5704
receive_buf+0x284/0x30b0 drivers/net/virtio_net.c:1061
virtnet_receive drivers/net/virtio_net.c:1323 [inline]
virtnet_poll+0x436/0x7d0 drivers/net/virtio_net.c:1428
napi_poll net/core/dev.c:6352 [inline]
net_rx_action+0x3ae/0xa50 net/core/dev.c:6418
read to 0xffff88812665f32c of 4 bytes by task 7292 on cpu 0:
tcp_space include/net/tcp.h:1373 [inline]
tcp_grow_window.isra.0+0x6b/0x480 net/ipv4/tcp_input.c:413
tcp_event_data_recv+0x68f/0x990 net/ipv4/tcp_input.c:717
tcp_rcv_established+0xbfe/0xf50 net/ipv4/tcp_input.c:5618
tcp_v4_do_rcv+0x381/0x4e0 net/ipv4/tcp_ipv4.c:1542
sk_backlog_rcv include/net/sock.h:945 [inline]
__release_sock+0x135/0x1e0 net/core/sock.c:2427
release_sock+0x61/0x160 net/core/sock.c:2943
tcp_recvmsg+0x63b/0x1a30 net/ipv4/tcp.c:2181
inet_recvmsg+0xbb/0x250 net/ipv4/af_inet.c:838
sock_recvmsg_nosec net/socket.c:871 [inline]
sock_recvmsg net/socket.c:889 [inline]
sock_recvmsg+0x92/0xb0 net/socket.c:885
sock_read_iter+0x15f/0x1e0 net/socket.c:967
call_read_iter include/linux/fs.h:1864 [inline]
new_sync_read+0x389/0x4f0 fs/read_write.c:414
__vfs_read+0xb1/0xc0 fs/read_write.c:427
vfs_read fs/read_write.c:461 [inline]
vfs_read+0x143/0x2c0 fs/read_write.c:446
Reported by Kernel Concurrency Sanitizer on:
CPU: 0 PID: 7292 Comm: syz-fuzzer Not tainted 5.3.0+ #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
sk_add_backlog() callers usually read sk->sk_rcvbuf without
owning the socket lock. This means sk_rcvbuf value can
be changed by other cpus, and KCSAN complains.
Add READ_ONCE() annotations to document the lockless nature
of these reads.
Note that writes over sk_rcvbuf should also use WRITE_ONCE(),
but this will be done in separate patches to ease stable
backports (if we decide this is relevant for stable trees).
BUG: KCSAN: data-race in tcp_add_backlog / tcp_recvmsg
write to 0xffff88812ab369f8 of 8 bytes by interrupt on cpu 1:
__sk_add_backlog include/net/sock.h:902 [inline]
sk_add_backlog include/net/sock.h:933 [inline]
tcp_add_backlog+0x45a/0xcc0 net/ipv4/tcp_ipv4.c:1737
tcp_v4_rcv+0x1aba/0x1bf0 net/ipv4/tcp_ipv4.c:1925
ip_protocol_deliver_rcu+0x51/0x470 net/ipv4/ip_input.c:204
ip_local_deliver_finish+0x110/0x140 net/ipv4/ip_input.c:231
NF_HOOK include/linux/netfilter.h:305 [inline]
NF_HOOK include/linux/netfilter.h:299 [inline]
ip_local_deliver+0x133/0x210 net/ipv4/ip_input.c:252
dst_input include/net/dst.h:442 [inline]
ip_rcv_finish+0x121/0x160 net/ipv4/ip_input.c:413
NF_HOOK include/linux/netfilter.h:305 [inline]
NF_HOOK include/linux/netfilter.h:299 [inline]
ip_rcv+0x18f/0x1a0 net/ipv4/ip_input.c:523
__netif_receive_skb_one_core+0xa7/0xe0 net/core/dev.c:5004
__netif_receive_skb+0x37/0xf0 net/core/dev.c:5118
netif_receive_skb_internal+0x59/0x190 net/core/dev.c:5208
napi_skb_finish net/core/dev.c:5671 [inline]
napi_gro_receive+0x28f/0x330 net/core/dev.c:5704
receive_buf+0x284/0x30b0 drivers/net/virtio_net.c:1061
virtnet_receive drivers/net/virtio_net.c:1323 [inline]
virtnet_poll+0x436/0x7d0 drivers/net/virtio_net.c:1428
napi_poll net/core/dev.c:6352 [inline]
net_rx_action+0x3ae/0xa50 net/core/dev.c:6418
read to 0xffff88812ab369f8 of 8 bytes by task 7271 on cpu 0:
tcp_recvmsg+0x470/0x1a30 net/ipv4/tcp.c:2047
inet_recvmsg+0xbb/0x250 net/ipv4/af_inet.c:838
sock_recvmsg_nosec net/socket.c:871 [inline]
sock_recvmsg net/socket.c:889 [inline]
sock_recvmsg+0x92/0xb0 net/socket.c:885
sock_read_iter+0x15f/0x1e0 net/socket.c:967
call_read_iter include/linux/fs.h:1864 [inline]
new_sync_read+0x389/0x4f0 fs/read_write.c:414
__vfs_read+0xb1/0xc0 fs/read_write.c:427
vfs_read fs/read_write.c:461 [inline]
vfs_read+0x143/0x2c0 fs/read_write.c:446
ksys_read+0xd5/0x1b0 fs/read_write.c:587
__do_sys_read fs/read_write.c:597 [inline]
__se_sys_read fs/read_write.c:595 [inline]
__x64_sys_read+0x4c/0x60 fs/read_write.c:595
do_syscall_64+0xcf/0x2f0 arch/x86/entry/common.c:296
entry_SYSCALL_64_after_hwframe+0x44/0xa9
Reported by Kernel Concurrency Sanitizer on:
CPU: 0 PID: 7271 Comm: syz-fuzzer Not tainted 5.3.0+ #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
__tipc_nl_compat_dumpit() calls tipc_nl_publ_dump() which expects
the attrs to be available by genl_dumpit_info(cb)->attrs. Add info
struct and attr parsing in compat dumpit function.
Reported-by: syzbot+8d37c50ffb0f52941a5e@syzkaller.appspotmail.com
Fixes: 057af70713 ("net: tipc: have genetlink code to parse the attrs during dumpit")
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
As this is the last user of genl_family_attrbuf, convert to allocate
attrs locally and do it in a similar way this is done in compat_doit().
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Benefit from the fact that the generic netlink code can parse the attrs
for dumpit op and avoid need to parse it in the op callback.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We have identified a problem with the "oversubscription" policy in the
link transmission code.
When small messages are transmitted, and the sending link has reached
the transmit window limit, those messages will be bundled and put into
the link backlog queue. However, bundles of data messages are counted
at the 'CRITICAL' level, so that the counter for that level, instead of
the counter for the real, bundled message's level is the one being
increased.
Subsequent, to-be-bundled data messages at non-CRITICAL levels continue
to be tested against the unchanged counter for their own level, while
contributing to an unrestrained increase at the CRITICAL backlog level.
This leaves a gap in congestion control algorithm for small messages
that can result in starvation for other users or a "real" CRITICAL
user. Even that eventually can lead to buffer exhaustion & link reset.
We fix this by keeping a 'target_bskb' buffer pointer at each levels,
then when bundling, we only bundle messages at the same importance
level only. This way, we know exactly how many slots a certain level
have occupied in the queue, so can manage level congestion accurately.
By bundling messages at the same level, we even have more benefits. Let
consider this:
- One socket sends 64-byte messages at the 'CRITICAL' level;
- Another sends 4096-byte messages at the 'LOW' level;
When a 64-byte message comes and is bundled the first time, we put the
overhead of message bundle to it (+ 40-byte header, data copy, etc.)
for later use, but the next message can be a 4096-byte one that cannot
be bundled to the previous one. This means the last bundle carries only
one payload message which is totally inefficient, as for the receiver
also! Later on, another 64-byte message comes, now we make a new bundle
and the same story repeats...
With the new bundling algorithm, this will not happen, the 64-byte
messages will be bundled together even when the 4096-byte message(s)
comes in between. However, if the 4096-byte messages are sent at the
same level i.e. 'CRITICAL', the bundling algorithm will again cause the
same overhead.
Also, the same will happen even with only one socket sending small
messages at a rate close to the link transmit's one, so that, when one
message is bundled, it's transmitted shortly. Then, another message
comes, a new bundle is created and so on...
We will solve this issue radically by another patch.
Fixes: 365ad353c2 ("tipc: reduce risk of user starvation during link congestion")
Reported-by: Hoang Le <hoang.h.le@dektech.com.au>
Acked-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: Tuong Lien <tuong.t.lien@dektech.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
The policy for handling the skb list locks on the send and receive paths
is simple.
- On the send path we never need to grab the lock on the 'xmitq' list
when the destination is an exernal node.
- On the receive path we always need to grab the lock on the 'inputq'
list, irrespective of source node.
However, when transmitting node local messages those will eventually
end up on the receive path of a local socket, meaning that the argument
'xmitq' in tipc_node_xmit() will become the 'ínputq' argument in the
function tipc_sk_rcv(). This has been handled by always initializing
the spinlock of the 'xmitq' list at message creation, just in case it
may end up on the receive path later, and despite knowing that the lock
in most cases never will be used.
This approach is inaccurate and confusing, and has also concealed the
fact that the stated 'no lock grabbing' policy for the send path is
violated in some cases.
We now clean up this by never initializing the lock at message creation,
instead doing this at the moment we find that the message actually will
enter the receive path. At the same time we fix the four locations
where we incorrectly access the spinlock on the send/error path.
This patch also reverts commit d12cffe932 ("tipc: ensure head->lock
is initialised") which has now become redundant.
CC: Eric Dumazet <edumazet@google.com>
Reported-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Reviewed-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This commit eliminates the use of the link 'stale_limit' & 'prev_from'
(besides the already removed - 'stale_cnt') variables in the detection
of repeated retransmit failures as there is no proper way to initialize
them to avoid a false detection, i.e. it is not really a retransmission
failure but due to a garbage values in the variables.
Instead, a jiffies variable will be added to individual skbs (like the
way we restrict the skb retransmissions) in order to mark the first skb
retransmit time. Later on, at the next retransmissions, the timestamp
will be checked to see if the skb in the link transmq is "too stale",
that is, the link tolerance time has passed, so that a link reset will
be ordered. Note, just checking on the first skb in the queue is fine
enough since it must be the oldest one.
A counter is also added to keep track the actual skb retransmissions'
number for later checking when the failure happens.
The downside of this approach is that the skb->cb[] buffer is about to
be exhausted, however it is always able to allocate another memory area
and keep a reference to it when needed.
Fixes: 77cf8edbc0 ("tipc: simplify stale link failure criteria")
Reported-by: Hoang Le <hoang.h.le@dektech.com.au>
Acked-by: Ying Xue <ying.xue@windriver.com>
Acked-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: Tuong Lien <tuong.t.lien@dektech.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
We set the field 'addr_trial_end' to 'jiffies', instead of the current
value 0, at the moment the node address is initialized. This guarantees
we don't inadvertently enter an address trial period when the node
address is explicitly set by the user.
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Acked-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since node internal messages are passed directly to the socket, it is not
possible to observe those messages via tcpdump or wireshark.
We now remedy this by making it possible to clone such messages and send
the clones to the loopback interface. The clones are dropped at reception
and have no functional role except making the traffic visible.
The feature is enabled if network taps are active for the loopback device.
pcap filtering restrictions require the messages to be presented to the
receiving side of the loopback device.
v3 - Function dev_nit_active used to check for network taps.
- Procedure netif_rx_ni used to send cloned messages to loopback device.
Signed-off-by: John Rutherford <john.rutherford@dektech.com.au>
Acked-by: Jon Maloy <jon.maloy@ericsson.com>
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In commit 365ad353c2 ("tipc: reduce risk of user starvation during
link congestion") we allowed senders to add exactly one list of extra
buffers to the link backlog queues during link congestion (aka
"oversubscription"). However, the criteria for when to stop adding
wakeup messages to the input queue when the overload abates is
inaccurate, and may cause starvation problems during very high load.
Currently, we stop adding wakeup messages after 10 total failed attempts
where we find that there is no space left in the backlog queue for a
certain importance level. The counter for this is accumulated across all
levels, which may lead the algorithm to leave the loop prematurely,
although there may still be plenty of space available at some levels.
The result is sometimes that messages near the wakeup queue tail are not
added to the input queue as they should be.
We now introduce a more exact algorithm, where we keep adding wakeup
messages to a level as long as the backlog queue has free slots for
the corresponding level, and stop at the moment there are no more such
slots or when there are no more wakeup messages to dequeue.
Fixes: 365ad35 ("tipc: reduce risk of user starvation during link congestion")
Reported-by: Tung Nguyen <tung.q.nguyen@dektech.com.au>
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 2753ca5d90 ("tipc: fix uninit-value in tipc_nl_compat_doit")
broke older tipc tools that use compat interface (e.g. tipc-config from
tipcutils package):
% tipc-config -p
operation not supported
The commit started to reject TIPC netlink compat messages that do not
have attributes. It is too restrictive because some of such messages are
valid (they don't need any arguments):
% grep 'tx none' include/uapi/linux/tipc_config.h
#define TIPC_CMD_NOOP 0x0000 /* tx none, rx none */
#define TIPC_CMD_GET_MEDIA_NAMES 0x0002 /* tx none, rx media_name(s) */
#define TIPC_CMD_GET_BEARER_NAMES 0x0003 /* tx none, rx bearer_name(s) */
#define TIPC_CMD_SHOW_PORTS 0x0006 /* tx none, rx ultra_string */
#define TIPC_CMD_GET_REMOTE_MNG 0x4003 /* tx none, rx unsigned */
#define TIPC_CMD_GET_MAX_PORTS 0x4004 /* tx none, rx unsigned */
#define TIPC_CMD_GET_NETID 0x400B /* tx none, rx unsigned */
#define TIPC_CMD_NOT_NET_ADMIN 0xC001 /* tx none, rx none */
This patch relaxes the original fix and rejects messages without
arguments only if such arguments are expected by a command (reg_type is
non zero).
Fixes: 2753ca5d90 ("tipc: fix uninit-value in tipc_nl_compat_doit")
Cc: stable@vger.kernel.org
Signed-off-by: Taras Kondratiuk <takondra@cisco.com>
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In conjunction with changing the interfaces' MTU (e.g. especially in
the case of a bonding) where the TIPC links are brought up and down
in a short time, a couple of issues were detected with the current link
changeover mechanism:
1) When one link is up but immediately forced down again, the failover
procedure will be carried out in order to failover all the messages in
the link's transmq queue onto the other working link. The link and node
state is also set to FAILINGOVER as part of the process. The message
will be transmited in form of a FAILOVER_MSG, so its size is plus of 40
bytes (= the message header size). There is no problem if the original
message size is not larger than the link's MTU - 40, and indeed this is
the max size of a normal payload messages. However, in the situation
above, because the link has just been up, the messages in the link's
transmq are almost SYNCH_MSGs which had been generated by the link
synching procedure, then their size might reach the max value already!
When the FAILOVER_MSG is built on the top of such a SYNCH_MSG, its size
will exceed the link's MTU. As a result, the messages are dropped
silently and the failover procedure will never end up, the link will
not be able to exit the FAILINGOVER state, so cannot be re-established.
2) The same scenario above can happen more easily in case the MTU of
the links is set differently or when changing. In that case, as long as
a large message in the failure link's transmq queue was built and
fragmented with its link's MTU > the other link's one, the issue will
happen (there is no need of a link synching in advance).
3) The link synching procedure also faces with the same issue but since
the link synching is only started upon receipt of a SYNCH_MSG, dropping
the message will not result in a state deadlock, but it is not expected
as design.
The 1) & 3) issues are resolved by the last commit that only a dummy
SYNCH_MSG (i.e. without data) is generated at the link synching, so the
size of a FAILOVER_MSG if any then will never exceed the link's MTU.
For the 2) issue, the only solution is trying to fragment the messages
in the failure link's transmq queue according to the working link's MTU
so they can be failovered then. A new function is made to accomplish
this, it will still be a TUNNEL PROTOCOL/FAILOVER MSG but if the
original message size is too large, it will be fragmented & reassembled
at the receiving side.
Acked-by: Ying Xue <ying.xue@windriver.com>
Acked-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: Tuong Lien <tuong.t.lien@dektech.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
This commit along with the next one are to resolve the issues with the
link changeover mechanism. See that commit for details.
Basically, for the link synching, from now on, we will send only one
single ("dummy") SYNCH message to peer. The SYNCH message does not
contain any data, just a header conveying the synch point to the peer.
A new node capability flag ("TIPC_TUNNEL_ENHANCED") is introduced for
backward compatible!
Acked-by: Ying Xue <ying.xue@windriver.com>
Acked-by: Jon Maloy <jon.maloy@ericsson.com>
Suggested-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: Tuong Lien <tuong.t.lien@dektech.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
s/tipc_toprsv_listener_data_ready/tipc_topsrv_listener_data_ready/
(r and s switched in topsrv)
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes from David Miller:
1) Fix AF_XDP cq entry leak, from Ilya Maximets.
2) Fix handling of PHY power-down on RTL8411B, from Heiner Kallweit.
3) Add some new PCI IDs to iwlwifi, from Ihab Zhaika.
4) Fix handling of neigh timers wrt. entries added by userspace, from
Lorenzo Bianconi.
5) Various cases of missing of_node_put(), from Nishka Dasgupta.
6) The new NET_ACT_CT needs to depend upon NF_NAT, from Yue Haibing.
7) Various RDS layer fixes, from Gerd Rausch.
8) Fix some more fallout from TCQ_F_CAN_BYPASS generalization, from
Cong Wang.
9) Fix FIB source validation checks over loopback, also from Cong Wang.
10) Use promisc for unsupported number of filters, from Justin Chen.
11) Missing sibling route unlink on failure in ipv6, from Ido Schimmel.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (90 commits)
tcp: fix tcp_set_congestion_control() use from bpf hook
ag71xx: fix return value check in ag71xx_probe()
ag71xx: fix error return code in ag71xx_probe()
usb: qmi_wwan: add D-Link DWM-222 A2 device ID
bnxt_en: Fix VNIC accounting when enabling aRFS on 57500 chips.
net: dsa: sja1105: Fix missing unlock on error in sk_buff()
gve: replace kfree with kvfree
selftests/bpf: fix test_xdp_noinline on s390
selftests/bpf: fix "valid read map access into a read-only array 1" on s390
net/mlx5: Replace kfree with kvfree
MAINTAINERS: update netsec driver
ipv6: Unlink sibling route in case of failure
liquidio: Replace vmalloc + memset with vzalloc
udp: Fix typo in net/ipv4/udp.c
net: bcmgenet: use promisc for unsupported filters
ipv6: rt6_check should return NULL if 'from' is NULL
tipc: initialize 'validated' field of received packets
selftests: add a test case for rp_filter
fib: relax source validation check for loopback packets
mlxsw: spectrum: Do not process learned records with a dummy FID
...
In the sysctl code the proc_dointvec_minmax() function is often used to
validate the user supplied value between an allowed range. This
function uses the extra1 and extra2 members from struct ctl_table as
minimum and maximum allowed value.
On sysctl handler declaration, in every source file there are some
readonly variables containing just an integer which address is assigned
to the extra1 and extra2 members, so the sysctl range is enforced.
The special values 0, 1 and INT_MAX are very often used as range
boundary, leading duplication of variables like zero=0, one=1,
int_max=INT_MAX in different source files:
$ git grep -E '\.extra[12].*&(zero|one|int_max)' |wc -l
248
Add a const int array containing the most commonly used values, some
macros to refer more easily to the correct array member, and use them
instead of creating a local one for every object file.
This is the bloat-o-meter output comparing the old and new binary
compiled with the default Fedora config:
# scripts/bloat-o-meter -d vmlinux.o.old vmlinux.o
add/remove: 2/2 grow/shrink: 0/2 up/down: 24/-188 (-164)
Data old new delta
sysctl_vals - 12 +12
__kstrtab_sysctl_vals - 12 +12
max 14 10 -4
int_max 16 - -16
one 68 - -68
zero 128 28 -100
Total: Before=20583249, After=20583085, chg -0.00%
[mcroce@redhat.com: tipc: remove two unused variables]
Link: http://lkml.kernel.org/r/20190530091952.4108-1-mcroce@redhat.com
[akpm@linux-foundation.org: fix net/ipv6/sysctl_net_ipv6.c]
[arnd@arndb.de: proc/sysctl: make firmware loader table conditional]
Link: http://lkml.kernel.org/r/20190617130014.1713870-1-arnd@arndb.de
[akpm@linux-foundation.org: fix fs/eventpoll.c]
Link: http://lkml.kernel.org/r/20190430180111.10688-1-mcroce@redhat.com
Signed-off-by: Matteo Croce <mcroce@redhat.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Aaron Tomlin <atomlin@redhat.com>
Cc: Matthew Wilcox <willy@infradead.org>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The tipc_msg_validate() function leaves a boolean flag 'validated' in
the validated buffer's control block, to avoid performing this action
more than once. However, at reception of new packets, the position of
this field may already have been set by lower layer protocols, so
that the packet is erroneously perceived as already validated by TIPC.
We fix this by initializing the said field to 'false' before performing
the initial validation.
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
tipc_named_node_up() creates a skb list. It passes the list to
tipc_node_xmit() which has some code paths that can call
skb_queue_purge() which relies on the list->lock being initialised.
The spin_lock is only needed if the messages end up on the receive path
but when the list is created in tipc_named_node_up() we don't
necessarily know if it is going to end up there.
Once all the skb list users are updated in tipc it will then be possible
to update them to use the unlocked variants of the skb list functions
and initialise the lock when we know the message will follow the receive
path.
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Acked-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking updates from David Miller:
"Some highlights from this development cycle:
1) Big refactoring of ipv6 route and neigh handling to support
nexthop objects configurable as units from userspace. From David
Ahern.
2) Convert explored_states in BPF verifier into a hash table,
significantly decreased state held for programs with bpf2bpf
calls, from Alexei Starovoitov.
3) Implement bpf_send_signal() helper, from Yonghong Song.
4) Various classifier enhancements to mvpp2 driver, from Maxime
Chevallier.
5) Add aRFS support to hns3 driver, from Jian Shen.
6) Fix use after free in inet frags by allocating fqdirs dynamically
and reworking how rhashtable dismantle occurs, from Eric Dumazet.
7) Add act_ctinfo packet classifier action, from Kevin
Darbyshire-Bryant.
8) Add TFO key backup infrastructure, from Jason Baron.
9) Remove several old and unused ISDN drivers, from Arnd Bergmann.
10) Add devlink notifications for flash update status to mlxsw driver,
from Jiri Pirko.
11) Lots of kTLS offload infrastructure fixes, from Jakub Kicinski.
12) Add support for mv88e6250 DSA chips, from Rasmus Villemoes.
13) Various enhancements to ipv6 flow label handling, from Eric
Dumazet and Willem de Bruijn.
14) Support TLS offload in nfp driver, from Jakub Kicinski, Dirk van
der Merwe, and others.
15) Various improvements to axienet driver including converting it to
phylink, from Robert Hancock.
16) Add PTP support to sja1105 DSA driver, from Vladimir Oltean.
17) Add mqprio qdisc offload support to dpaa2-eth, from Ioana
Radulescu.
18) Add devlink health reporting to mlx5, from Moshe Shemesh.
19) Convert stmmac over to phylink, from Jose Abreu.
20) Add PTP PHC (Physical Hardware Clock) support to mlxsw, from
Shalom Toledo.
21) Add nftables SYNPROXY support, from Fernando Fernandez Mancera.
22) Convert tcp_fastopen over to use SipHash, from Ard Biesheuvel.
23) Track spill/fill of constants in BPF verifier, from Alexei
Starovoitov.
24) Support bounded loops in BPF, from Alexei Starovoitov.
25) Various page_pool API fixes and improvements, from Jesper Dangaard
Brouer.
26) Just like ipv4, support ref-countless ipv6 route handling. From
Wei Wang.
27) Support VLAN offloading in aquantia driver, from Igor Russkikh.
28) Add AF_XDP zero-copy support to mlx5, from Maxim Mikityanskiy.
29) Add flower GRE encap/decap support to nfp driver, from Pieter
Jansen van Vuuren.
30) Protect against stack overflow when using act_mirred, from John
Hurley.
31) Allow devmap map lookups from eBPF, from Toke Høiland-Jørgensen.
32) Use page_pool API in netsec driver, Ilias Apalodimas.
33) Add Google gve network driver, from Catherine Sullivan.
34) More indirect call avoidance, from Paolo Abeni.
35) Add kTLS TX HW offload support to mlx5, from Tariq Toukan.
36) Add XDP_REDIRECT support to bnxt_en, from Andy Gospodarek.
37) Add MPLS manipulation actions to TC, from John Hurley.
38) Add sending a packet to connection tracking from TC actions, and
then allow flower classifier matching on conntrack state. From
Paul Blakey.
39) Netfilter hw offload support, from Pablo Neira Ayuso"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (2080 commits)
net/mlx5e: Return in default case statement in tx_post_resync_params
mlx5: Return -EINVAL when WARN_ON_ONCE triggers in mlx5e_tls_resync().
net: dsa: add support for BRIDGE_MROUTER attribute
pkt_sched: Include const.h
net: netsec: remove static declaration for netsec_set_tx_de()
net: netsec: remove superfluous if statement
netfilter: nf_tables: add hardware offload support
net: flow_offload: rename tc_cls_flower_offload to flow_cls_offload
net: flow_offload: add flow_block_cb_is_busy() and use it
net: sched: remove tcf block API
drivers: net: use flow block API
net: sched: use flow block API
net: flow_offload: add flow_block_cb_{priv, incref, decref}()
net: flow_offload: add list handling functions
net: flow_offload: add flow_block_cb_alloc() and flow_block_cb_free()
net: flow_offload: rename TCF_BLOCK_BINDER_TYPE_* to FLOW_BLOCK_BINDER_TYPE_*
net: flow_offload: rename TC_BLOCK_{UN}BIND to FLOW_BLOCK_{UN}BIND
net: flow_offload: add flow_block_cb_setup_simple()
net: hisilicon: Add an tx_desc to adapt HI13X1_GMAC
net: hisilicon: Add an rx_desc to adapt HI13X1_GMAC
...
- A fair pile of RST conversions, many from Mauro. These create more
than the usual number of simple but annoying merge conflicts with other
trees, unfortunately. He has a lot more of these waiting on the wings
that, I think, will go to you directly later on.
- A new document on how to use merges and rebases in kernel repos, and one
on Spectre vulnerabilities.
- Various improvements to the build system, including automatic markup of
function() references because some people, for reasons I will never
understand, were of the opinion that :c:func:``function()`` is
unattractive and not fun to type.
- We now recommend using sphinx 1.7, but still support back to 1.4.
- Lots of smaller improvements, warning fixes, typo fixes, etc.
-----BEGIN PGP SIGNATURE-----
iQFDBAABCAAtFiEEIw+MvkEiF49krdp9F0NaE2wMflgFAl0krAEPHGNvcmJldEBs
d24ubmV0AAoJEBdDWhNsDH5Yg98H/AuLqO9LpOgUjF4LhyjxGPdzJkY9RExSJ7km
gznyreLCZgFaJR+AY6YDsd4Jw6OJlPbu1YM/Qo3C3WrZVFVhgL/s2ebvBgCo50A8
raAFd8jTf4/mGCHnAqRotAPQ3mETJUk315B66lBJ6Oc+YdpRhwXWq8ZW2bJxInFF
3HDvoFgMf0KhLuMHUkkL0u3fxH1iA+KvDu8diPbJYFjOdOWENz/CV8wqdVkXRSEW
DJxIq89h/7d+hIG3d1I7Nw+gibGsAdjSjKv4eRKauZs4Aoxd1Gpl62z0JNk6aT3m
dtq4joLdwScydonXROD/Twn2jsu4xYTrPwVzChomElMowW/ZBBY=
=D0eO
-----END PGP SIGNATURE-----
Merge tag 'docs-5.3' of git://git.lwn.net/linux
Pull Documentation updates from Jonathan Corbet:
"It's been a relatively busy cycle for docs:
- A fair pile of RST conversions, many from Mauro. These create more
than the usual number of simple but annoying merge conflicts with
other trees, unfortunately. He has a lot more of these waiting on
the wings that, I think, will go to you directly later on.
- A new document on how to use merges and rebases in kernel repos,
and one on Spectre vulnerabilities.
- Various improvements to the build system, including automatic
markup of function() references because some people, for reasons I
will never understand, were of the opinion that
:c:func:``function()`` is unattractive and not fun to type.
- We now recommend using sphinx 1.7, but still support back to 1.4.
- Lots of smaller improvements, warning fixes, typo fixes, etc"
* tag 'docs-5.3' of git://git.lwn.net/linux: (129 commits)
docs: automarkup.py: ignore exceptions when seeking for xrefs
docs: Move binderfs to admin-guide
Disable Sphinx SmartyPants in HTML output
doc: RCU callback locks need only _bh, not necessarily _irq
docs: format kernel-parameters -- as code
Doc : doc-guide : Fix a typo
platform: x86: get rid of a non-existent document
Add the RCU docs to the core-api manual
Documentation: RCU: Add TOC tree hooks
Documentation: RCU: Rename txt files to rst
Documentation: RCU: Convert RCU UP systems to reST
Documentation: RCU: Convert RCU linked list to reST
Documentation: RCU: Convert RCU basic concepts to reST
docs: filesystems: Remove uneeded .rst extension on toctables
scripts/sphinx-pre-install: fix out-of-tree build
docs: zh_CN: submitting-drivers.rst: Remove a duplicated Documentation/
Documentation: PGP: update for newer HW devices
Documentation: Add section about CPU vulnerabilities for Spectre
Documentation: platform: Delete x86-laptop-drivers.txt
docs: Note that :c:func: should no longer be used
...
For these places are protected by rcu_read_lock, we change from
rcu_dereference_rtnl to rcu_dereference, as there is no need to
check if rtnl lock is held.
For these places are protected by rtnl_lock, we change from
rcu_dereference_rtnl to rtnl_dereference/rcu_dereference_protected,
as no extra memory barriers are needed under rtnl_lock() which also
protects tn->bearer_list[] and dev->tipc_ptr/b->media_ptr updating.
rcu_dereference_rtnl will be only used in the places where it could
be under rcu_read_lock or rtnl_lock.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Both tipc_udp_enable and tipc_udp_disable are called under rtnl_lock,
ub->ubsock could never be NULL in tipc_udp_disable and cleanup_bearer,
so remove the check.
Also remove the one in tipc_udp_enable by adding "free" label.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The macro TIPC_BC_RETR_LIM is always used in combination with 'jiffies',
so we can just as well perform the addition in the macro itself. This
way, we get a few shorter code lines and one less line break.
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As other udp/ip tunnels do, tipc udp media should also have a
lockless dst_cache supported on its tx path.
Here we add dst_cache into udp_replicast to support dst cache
for both rmcast and rcast, and rmcast uses ub->rcast and each
rcast uses its own node in ub->rcast.list.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The new route handling in ip_mc_finish_output() from 'net' overlapped
with the new support for returning congestion notifications from BPF
programs.
In order to handle this I had to take the dev_loopback_xmit() calls
out of the switch statement.
The aquantia driver conflicts were simple overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
We rename the inline function msg_get_wrapped() to the more
comprehensible msg_inner_hdr().
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We increase the allocated headroom for the buffer copies to be
retransmitted. This eliminates the need for the lower stack levels
(UDP/IP/L2) to expand the headroom in order to add their own headers.
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In commit a4dc70d46c ("tipc: extend link reset criteria for stale
packet retransmission") we made link retransmission failure events
dependent on the link tolerance, and not only of the number of failed
retransmission attempts, as we did earlier. This works well. However,
keeping the original, additional criteria of 99 failed retransmissions
is now redundant, and may in some cases lead to failure detection
times in the order of minutes instead of the expected 1.5 sec link
tolerance value.
We now remove this criteria altogether.
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is to fix an uninit-value issue, reported by syzbot:
BUG: KMSAN: uninit-value in memchr+0xce/0x110 lib/string.c:981
Call Trace:
__dump_stack lib/dump_stack.c:77 [inline]
dump_stack+0x191/0x1f0 lib/dump_stack.c:113
kmsan_report+0x130/0x2a0 mm/kmsan/kmsan.c:622
__msan_warning+0x75/0xe0 mm/kmsan/kmsan_instr.c:310
memchr+0xce/0x110 lib/string.c:981
string_is_valid net/tipc/netlink_compat.c:176 [inline]
tipc_nl_compat_bearer_disable+0x2a1/0x480 net/tipc/netlink_compat.c:449
__tipc_nl_compat_doit net/tipc/netlink_compat.c:327 [inline]
tipc_nl_compat_doit+0x3ac/0xb00 net/tipc/netlink_compat.c:360
tipc_nl_compat_handle net/tipc/netlink_compat.c:1178 [inline]
tipc_nl_compat_recv+0x1b1b/0x27b0 net/tipc/netlink_compat.c:1281
TLV_GET_DATA_LEN() may return a negtive int value, which will be
used as size_t (becoming a big unsigned long) passed into memchr,
cause this issue.
Similar to what it does in tipc_nl_compat_bearer_enable(), this
fix is to return -EINVAL when TLV_GET_DATA_LEN() is negtive in
tipc_nl_compat_bearer_disable(), as well as in
tipc_nl_compat_link_stat_dump() and tipc_nl_compat_link_reset_stats().
v1->v2:
- add the missing Fixes tags per Eric's request.
Fixes: 0762216c0a ("tipc: fix uninit-value in tipc_nl_compat_bearer_enable")
Fixes: 8b66fee7f8 ("tipc: fix uninit-value in tipc_nl_compat_link_reset_stats")
Reported-by: syzbot+30eaa8bf392f7fafffaf@syzkaller.appspotmail.com
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
tipc_nl_compat_bearer_set() is only called by tipc_nl_compat_link_set()
which already does the check for msg->req check, so remove it from
tipc_nl_compat_bearer_set(), and do the same in tipc_nl_compat_media_set().
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix misalignment of policy statement in netlink.c due to automatic
spatch code transformation.
Fixes: 3b0f31f2b8 ("genetlink: make policy common to family")
Acked-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: John Rutherford <john.rutherford@dektech.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is to fix a dst defcnt leak, which can be reproduced by doing:
# ip net a c; ip net a s; modprobe tipc
# ip net e s ip l a n eth1 type veth peer n eth1 netns c
# ip net e c ip l s lo up; ip net e c ip l s eth1 up
# ip net e s ip l s lo up; ip net e s ip l s eth1 up
# ip net e c ip a a 1.1.1.2/8 dev eth1
# ip net e s ip a a 1.1.1.1/8 dev eth1
# ip net e c tipc b e m udp n u1 localip 1.1.1.2
# ip net e s tipc b e m udp n u1 localip 1.1.1.1
# ip net d c; ip net d s; rmmod tipc
and it will get stuck and keep logging the error:
unregister_netdevice: waiting for lo to become free. Usage count = 1
The cause is that a dst is held by the udp sock's sk_rx_dst set on udp rx
path with udp_early_demux == 1, and this dst (eventually holding lo dev)
can't be released as bearer's removal in tipc pernet .exit happens after
lo dev's removal, default_device pernet .exit.
"There are two distinct types of pernet_operations recognized: subsys and
device. At creation all subsys init functions are called before device
init functions, and at destruction all device exit functions are called
before subsys exit function."
So by calling register_pernet_device instead to register tipc_net_ops, the
pernet .exit() will be invoked earlier than loopback dev's removal when a
netns is being destroyed, as fou/gue does.
Note that vxlan and geneve udp tunnels don't have this issue, as the udp
sock is released in their device ndo_stop().
This fix is also necessary for tipc dst_cache, which will hold dsts on tx
path and I will introduce in my next patch.
Reported-by: Li Shuang <shuali@redhat.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
udp_tunnel(6)_xmit_skb() called by tipc_udp_xmit() expects a tunnel device
to count packets on dev->tstats, a perpcu variable. However, TIPC is using
udp tunnel with no tunnel device, and pass the lower dev, like veth device
that only initializes dev->lstats(a perpcu variable) when creating it.
Later iptunnel_xmit_stats() called by ip(6)tunnel_xmit() thinks the dev as
a tunnel device, and uses dev->tstats instead of dev->lstats. tstats' each
pointer points to a bigger struct than lstats, so when tstats->tx_bytes is
increased, other percpu variable's members could be overwritten.
syzbot has reported quite a few crashes due to fib_nh_common percpu member
'nhc_pcpu_rth_output' overwritten, call traces are like:
BUG: KASAN: slab-out-of-bounds in rt_cache_valid+0x158/0x190
net/ipv4/route.c:1556
rt_cache_valid+0x158/0x190 net/ipv4/route.c:1556
__mkroute_output net/ipv4/route.c:2332 [inline]
ip_route_output_key_hash_rcu+0x819/0x2d50 net/ipv4/route.c:2564
ip_route_output_key_hash+0x1ef/0x360 net/ipv4/route.c:2393
__ip_route_output_key include/net/route.h:125 [inline]
ip_route_output_flow+0x28/0xc0 net/ipv4/route.c:2651
ip_route_output_key include/net/route.h:135 [inline]
...
or:
kasan: GPF could be caused by NULL-ptr deref or user memory access
RIP: 0010:dst_dev_put+0x24/0x290 net/core/dst.c:168
<IRQ>
rt_fibinfo_free_cpus net/ipv4/fib_semantics.c:200 [inline]
free_fib_info_rcu+0x2e1/0x490 net/ipv4/fib_semantics.c:217
__rcu_reclaim kernel/rcu/rcu.h:240 [inline]
rcu_do_batch kernel/rcu/tree.c:2437 [inline]
invoke_rcu_callbacks kernel/rcu/tree.c:2716 [inline]
rcu_process_callbacks+0x100a/0x1ac0 kernel/rcu/tree.c:2697
...
The issue exists since tunnel stats update is moved to iptunnel_xmit by
Commit 039f50629b ("ip_tunnel: Move stats update to iptunnel_xmit()"),
and here to fix it by passing a NULL tunnel dev to udp_tunnel(6)_xmit_skb
so that the packets counting won't happen on dev->tstats.
Reported-by: syzbot+9d4c12bfd45a58738d0a@syzkaller.appspotmail.com
Reported-by: syzbot+a9e23ea2aa21044c2798@syzkaller.appspotmail.com
Reported-by: syzbot+c4c4b2bb358bb936ad7e@syzkaller.appspotmail.com
Reported-by: syzbot+0290d2290a607e035ba1@syzkaller.appspotmail.com
Reported-by: syzbot+a43d8d4e7e8a7a9e149e@syzkaller.appspotmail.com
Reported-by: syzbot+a47c5f4c6c00fc1ed16e@syzkaller.appspotmail.com
Fixes: 039f50629b ("ip_tunnel: Move stats update to iptunnel_xmit()")
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It appears that a FAILOVER_MSG can come from peer even when the failure
link is resetting (i.e. just after the 'node_write_unlock()'...). This
means the failover procedure on the node has not been started yet.
The situation is as follows:
node1 node2
linkb linka linka linkb
| | | |
| | x failure |
| | RESETTING |
| | | |
| x failure RESET |
| RESETTING FAILINGOVER |
| | (FAILOVER_MSG) | |
|<-------------------------------------------------|
| *FAILINGOVER | | |
| | (dummy FAILOVER_MSG) | |
|------------------------------------------------->|
| RESET | | FAILOVER_END
| FAILINGOVER RESET |
. . . .
. . . .
. . . .
Once this happens, the link failover procedure will be triggered
wrongly on the receiving node since the node isn't in FAILINGOVER state
but then another link failover will be carried out.
The consequences are:
1) A peer might get stuck in FAILINGOVER state because the 'sync_point'
was set, reset and set incorrectly, the criteria to end the failover
would not be met, it could keep waiting for a message that has already
received.
2) The early FAILOVER_MSG(s) could be queued in the link failover
deferdq but would be purged or not pulled out because the 'drop_point'
was not set correctly.
3) The early FAILOVER_MSG(s) could be dropped too.
4) The dummy FAILOVER_MSG could make the peer leaving FAILINGOVER state
shortly, but later on it would be restarted.
The same situation can also happen when the link is in PEER_RESET state
and a FAILOVER_MSG arrives.
The commit resolves the issues by forcing the link down immediately, so
the failover procedure will be started normally (which is the same as
when receiving a FAILOVER_MSG and the link is in up state).
Also, the function "tipc_node_link_failover()" is toughen to avoid such
a situation from happening.
Acked-by: Jon Maloy <jon.maloy@ericsson.se>
Signed-off-by: Tuong Lien <tuong.t.lien@dektech.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
In patch series, commit 9195948fbf ("tipc: improve TIPC throughput by
Gap ACK blocks"), as for simplicity, the repeated retransmit failures'
detection in the function - "tipc_link_retrans()" was kept there for
broadcast retransmissions only.
This commit now reapplies this feature for link unicast retransmissions
that has been done via the function - "tipc_link_advance_transmq()".
Also, the "tipc_link_retrans()" is renamed to "tipc_link_bc_retrans()"
as it is used only for broadcast.
Acked-by: Jon Maloy <jon.maloy@ericsson.se>
Signed-off-by: Tuong Lien <tuong.t.lien@dektech.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Syzbot reported a memleak caused by grp members' deferredq list not
purged when the grp is be deleted.
The issue occurs when more(msg_grp_bc_seqno(hdr), m->bc_rcv_nxt) in
tipc_group_filter_msg() and the skb will stay in deferredq.
So fix it by calling __skb_queue_purge for each member's deferredq
in tipc_group_delete() when a tipc sk leaves the grp.
Fixes: b87a5ea31c ("tipc: guarantee group unicast doesn't bypass group broadcast")
Reported-by: syzbot+78fbe679c8ca8d264a8d@syzkaller.appspotmail.com
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The kbuild documentation clearly shows that the documents
there are written at different times: some use markdown,
some use their own peculiar logic to split sections.
Convert everything to ReST without affecting too much
the author's style and avoiding adding uneeded markups.
The conversion is actually:
- add blank lines and identation in order to identify paragraphs;
- fix tables markups;
- add some lists markups;
- mark literal blocks;
- adjust title markups.
At its new index.rst, let's add a :orphan: while this is not linked to
the main index.rst file, in order to avoid build warnings.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Pull networking fixes from David Miller:
1) Clear up some recent tipc regressions because of registration
ordering. Fix from Junwei Hu.
2) tipc's TLV_SET() can read past the end of the supplied buffer during
the copy. From Chris Packham.
3) ptp example program doesn't match the kernel, from Richard Cochran.
4) Outgoing message type fix in qrtr, from Bjorn Andersson.
5) Flow control regression in stmmac, from Tan Tee Min.
6) Fix inband autonegotiation in phylink, from Russell King.
7) Fix sk_bound_dev_if handling in rawv6_bind(), from Mike Manning.
8) Fix usbnet crash after disconnect, from Kloetzke Jan.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (21 commits)
usbnet: fix kernel crash after disconnect
selftests: fib_rule_tests: use pre-defined DEV_ADDR
net-next: net: Fix typos in ip-sysctl.txt
ipv6: Consider sk_bound_dev_if when binding a raw socket to an address
net: phylink: ensure inband AN works correctly
usbnet: ipheth: fix racing condition
net: stmmac: dma channel control register need to be init first
net: stmmac: fix ethtool flow control not able to get/set
net: qrtr: Fix message type of outgoing packets
networking: : fix typos in code comments
ptp: Fix example program to match kernel.
fddi: fix typos in code comments
selftests: fib_rule_tests: enable forwarding before ipv4 from/iif test
selftests: fib_rule_tests: fix local IPv4 address typo
tipc: Avoid copying bytes beyond the supplied data
2/2] net: xilinx_emaclite: use readx_poll_timeout() in mdio wait function
1/2] net: axienet: use readx_poll_timeout() in mdio wait function
vlan: Mark expected switch fall-through
macvlan: Mark expected switch fall-through
net/mlx4_en: ethtool, Remove unsupported SFP EEPROM high pages query
...
Here are series of patches that add SPDX tags to different kernel files,
based on two different things:
- SPDX entries are added to a bunch of files that we missed a year ago
that do not have any license information at all.
These were either missed because the tool saw the MODULE_LICENSE()
tag, or some EXPORT_SYMBOL tags, and got confused and thought the
file had a real license, or the files have been added since the last
big sweep, or they were Makefile/Kconfig files, which we didn't
touch last time.
- Add GPL-2.0-only or GPL-2.0-or-later tags to files where our scan
tools can determine the license text in the file itself. Where this
happens, the license text is removed, in order to cut down on the
700+ different ways we have in the kernel today, in a quest to get
rid of all of these.
These patches have been out for review on the linux-spdx@vger mailing
list, and while they were created by automatic tools, they were
hand-verified by a bunch of different people, all whom names are on the
patches are reviewers.
The reason for these "large" patches is if we were to continue to
progress at the current rate of change in the kernel, adding license
tags to individual files in different subsystems, we would be finished
in about 10 years at the earliest.
There will be more series of these types of patches coming over the next
few weeks as the tools and reviewers crunch through the more "odd"
variants of how to say "GPLv2" that developers have come up with over
the years, combined with other fun oddities (GPL + a BSD disclaimer?)
that are being unearthed, with the goal for the whole kernel to be
cleaned up.
These diffstats are not small, 3840 files are touched, over 10k lines
removed in just 24 patches.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXOP8uw8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ynmGQCgy3evqzleuOITDpuWaxewFdHqiJYAnA7KRw4H
1KwtfRnMtG6dk/XaS7H7
=O9lH
-----END PGP SIGNATURE-----
Merge tag 'spdx-5.2-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull SPDX update from Greg KH:
"Here is a series of patches that add SPDX tags to different kernel
files, based on two different things:
- SPDX entries are added to a bunch of files that we missed a year
ago that do not have any license information at all.
These were either missed because the tool saw the MODULE_LICENSE()
tag, or some EXPORT_SYMBOL tags, and got confused and thought the
file had a real license, or the files have been added since the
last big sweep, or they were Makefile/Kconfig files, which we
didn't touch last time.
- Add GPL-2.0-only or GPL-2.0-or-later tags to files where our scan
tools can determine the license text in the file itself. Where this
happens, the license text is removed, in order to cut down on the
700+ different ways we have in the kernel today, in a quest to get
rid of all of these.
These patches have been out for review on the linux-spdx@vger mailing
list, and while they were created by automatic tools, they were
hand-verified by a bunch of different people, all whom names are on
the patches are reviewers.
The reason for these "large" patches is if we were to continue to
progress at the current rate of change in the kernel, adding license
tags to individual files in different subsystems, we would be finished
in about 10 years at the earliest.
There will be more series of these types of patches coming over the
next few weeks as the tools and reviewers crunch through the more
"odd" variants of how to say "GPLv2" that developers have come up with
over the years, combined with other fun oddities (GPL + a BSD
disclaimer?) that are being unearthed, with the goal for the whole
kernel to be cleaned up.
These diffstats are not small, 3840 files are touched, over 10k lines
removed in just 24 patches"
* tag 'spdx-5.2-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (24 commits)
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 25
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 24
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 23
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 22
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 21
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 20
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 19
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 18
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 17
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 15
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 14
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 13
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 12
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 11
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 10
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 9
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 7
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 5
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 4
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 3
...
Add SPDX license identifiers to all Make/Kconfig files which:
- Have no license information of any form
These files fall under the project license, GPL v2 only. The resulting SPDX
license identifier is:
GPL-2.0-only
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Error message printed:
modprobe: ERROR: could not insert 'tipc': Address family not
supported by protocol.
when modprobe tipc after the following patch: switch order of
device registration, commit 7e27e8d613
("tipc: switch order of device registration to fix a crash")
Because sock_create_kern(net, AF_TIPC, ...) called by
tipc_topsrv_create_listener() in the initialization process
of tipc_init_net(), so tipc_socket_init() must be execute before that.
Meanwhile, tipc_net_id need to be initialized when sock_create()
called, and tipc_socket_init() is no need to be called for each namespace.
I add a variable tipc_topsrv_net_ops, and split the
register_pernet_subsys() of tipc into two parts, and split
tipc_socket_init() with initialization of pernet params.
By the way, I fixed resources rollback error when tipc_bcast_init()
failed in tipc_init_net().
Fixes: 7e27e8d613 ("tipc: switch order of device registration to fix a crash")
Signed-off-by: Junwei Hu <hujunwei4@huawei.com>
Reported-by: Wang Wang <wangwang2@huawei.com>
Reported-by: syzbot+1e8114b61079bfe9cbc5@syzkaller.appspotmail.com
Reviewed-by: Kang Zhou <zhoukang7@huawei.com>
Reviewed-by: Suanming Mou <mousuanming@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Error message printed:
modprobe: ERROR: could not insert 'tipc': Address family not
supported by protocol.
when modprobe tipc after the following patch: switch order of
device registration, commit 7e27e8d613
("tipc: switch order of device registration to fix a crash")
Because sock_create_kern(net, AF_TIPC, ...) is called by
tipc_topsrv_create_listener() in the initialization process
of tipc_net_ops, tipc_socket_init() must be execute before that.
I move tipc_socket_init() into function tipc_init_net().
Fixes: 7e27e8d613
("tipc: switch order of device registration to fix a crash")
Signed-off-by: Junwei Hu <hujunwei4@huawei.com>
Reported-by: Wang Wang <wangwang2@huawei.com>
Reviewed-by: Kang Zhou <zhoukang7@huawei.com>
Reviewed-by: Suanming Mou <mousuanming@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When tipc is loaded while many processes try to create a TIPC socket,
a crash occurs:
PANIC: Unable to handle kernel paging request at virtual
address "dfff20000000021d"
pc : tipc_sk_create+0x374/0x1180 [tipc]
lr : tipc_sk_create+0x374/0x1180 [tipc]
Exception class = DABT (current EL), IL = 32 bits
Call trace:
tipc_sk_create+0x374/0x1180 [tipc]
__sock_create+0x1cc/0x408
__sys_socket+0xec/0x1f0
__arm64_sys_socket+0x74/0xa8
...
This is due to race between sock_create and unfinished
register_pernet_device. tipc_sk_insert tries to do
"net_generic(net, tipc_net_id)".
but tipc_net_id is not initialized yet.
So switch the order of the two to close the race.
This can be reproduced with multiple processes doing socket(AF_TIPC, ...)
and one process doing module removal.
Fixes: a62fbccecd ("tipc: make subscriber server support net namespace")
Signed-off-by: Junwei Hu <hujunwei4@huawei.com>
Reported-by: Wang Wang <wangwang2@huawei.com>
Reviewed-by: Xiaogang Wang <wangxiaogang3@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit 517d7c79bd ("tipc: fix hanging poll() for stream sockets")
introduced a regression for clients using non-blocking sockets.
After the commit, we send EPOLLOUT event to the client even in
TIPC_CONNECTING state. This causes the subsequent send() to fail
with ENOTCONN, as the socket is still not in TIPC_ESTABLISHED state.
In this commit, we:
- improve the fix for hanging poll() by replacing sk_data_ready()
with sk_state_change() to wake up all clients.
- revert the faulty updates introduced by commit 517d7c79bd
("tipc: fix hanging poll() for stream sockets").
Fixes: 517d7c79bd ("tipc: fix hanging poll() for stream sockets")
Signed-off-by: Parthasarathy Bhuvaragan <parthasarathy.bhuvaragan@gmail.com>
Acked-by: Jon Maloy <jon.maloy@ericsson.se>
Signed-off-by: David S. Miller <davem@davemloft.net>
TIPC link can temporarily fall into "half-establish" that only one of
the link endpoints is ESTABLISHED and starts to send traffic, PROTOCOL
messages, whereas the other link endpoint is not up (e.g. immediately
when the endpoint receives ACTIVATE_MSG, the network interface goes
down...).
This is a normal situation and will be settled because the link
endpoint will be eventually brought down after the link tolerance time.
However, the situation will become worse when the second link is
established before the first link endpoint goes down,
For example:
1. Both links <1A-2A>, <1B-2B> down
2. Link endpoint 2A up, but 1A still down (e.g. due to network
disturbance, wrong session, etc.)
3. Link <1B-2B> up
4. Link endpoint 2A down (e.g. due to link tolerance timeout)
5. Node B starts failover onto link <1B-2B>
==> Node A does never start link failover.
When the "half-failover" situation happens, two consequences have been
observed:
a) Peer link/node gets stuck in FAILINGOVER state;
b) Traffic or user messages that peer node is trying to failover onto
the second link can be partially or completely dropped by this node.
The consequence a) was actually solved by commit c140eb166d ("tipc:
fix failover problem"), but that commit didn't cover the b). It's due
to the fact that the tunnel link endpoint has never been prepared for a
failover, so the 'l->drop_point' (and the other data...) is not set
correctly. When a TUNNEL_MSG from peer node arrives on the link,
depending on the inner message's seqno and the current 'l->drop_point'
value, the message can be dropped (- treated as a duplicate message) or
processed.
At this early stage, the traffic messages from peer are likely to be
NAME_DISTRIBUTORs, this means some name table entries will be missed on
the node forever!
The commit resolves the issue by starting the FAILOVER process on this
node as well. Another benefit from this solution is that we ensure the
link will not be re-established until the failover ends.
Acked-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: Tuong Lien <tuong.t.lien@dektech.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add options to strictly validate messages and dump messages,
sometimes perhaps validating dump messages non-strictly may
be required, so add an option for that as well.
Since none of this can really be applied to existing commands,
set the options everwhere using the following spatch:
@@
identifier ops;
expression X;
@@
struct genl_ops ops[] = {
...,
{
.cmd = X,
+ .validate = GENL_DONT_VALIDATE_STRICT | GENL_DONT_VALIDATE_DUMP,
...
},
...
};
For new commands one should just not copy the .validate 'opt-out'
flags and thus get strict validation.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We currently have two levels of strict validation:
1) liberal (default)
- undefined (type >= max) & NLA_UNSPEC attributes accepted
- attribute length >= expected accepted
- garbage at end of message accepted
2) strict (opt-in)
- NLA_UNSPEC attributes accepted
- attribute length >= expected accepted
Split out parsing strictness into four different options:
* TRAILING - check that there's no trailing data after parsing
attributes (in message or nested)
* MAXTYPE - reject attrs > max known type
* UNSPEC - reject attributes with NLA_UNSPEC policy entries
* STRICT_ATTRS - strictly validate attribute size
The default for future things should be *everything*.
The current *_strict() is a combination of TRAILING and MAXTYPE,
and is renamed to _deprecated_strict().
The current regular parsing has none of this, and is renamed to
*_parse_deprecated().
Additionally it allows us to selectively set one of the new flags
even on old policies. Notably, the UNSPEC flag could be useful in
this case, since it can be arranged (by filling in the policy) to
not be an incompatible userspace ABI change, but would then going
forward prevent forgetting attribute entries. Similar can apply
to the POLICY flag.
We end up with the following renames:
* nla_parse -> nla_parse_deprecated
* nla_parse_strict -> nla_parse_deprecated_strict
* nlmsg_parse -> nlmsg_parse_deprecated
* nlmsg_parse_strict -> nlmsg_parse_deprecated_strict
* nla_parse_nested -> nla_parse_nested_deprecated
* nla_validate_nested -> nla_validate_nested_deprecated
Using spatch, of course:
@@
expression TB, MAX, HEAD, LEN, POL, EXT;
@@
-nla_parse(TB, MAX, HEAD, LEN, POL, EXT)
+nla_parse_deprecated(TB, MAX, HEAD, LEN, POL, EXT)
@@
expression NLH, HDRLEN, TB, MAX, POL, EXT;
@@
-nlmsg_parse(NLH, HDRLEN, TB, MAX, POL, EXT)
+nlmsg_parse_deprecated(NLH, HDRLEN, TB, MAX, POL, EXT)
@@
expression NLH, HDRLEN, TB, MAX, POL, EXT;
@@
-nlmsg_parse_strict(NLH, HDRLEN, TB, MAX, POL, EXT)
+nlmsg_parse_deprecated_strict(NLH, HDRLEN, TB, MAX, POL, EXT)
@@
expression TB, MAX, NLA, POL, EXT;
@@
-nla_parse_nested(TB, MAX, NLA, POL, EXT)
+nla_parse_nested_deprecated(TB, MAX, NLA, POL, EXT)
@@
expression START, MAX, POL, EXT;
@@
-nla_validate_nested(START, MAX, POL, EXT)
+nla_validate_nested_deprecated(START, MAX, POL, EXT)
@@
expression NLH, HDRLEN, MAX, POL, EXT;
@@
-nlmsg_validate(NLH, HDRLEN, MAX, POL, EXT)
+nlmsg_validate_deprecated(NLH, HDRLEN, MAX, POL, EXT)
For this patch, don't actually add the strict, non-renamed versions
yet so that it breaks compile if I get it wrong.
Also, while at it, make nla_validate and nla_parse go down to a
common __nla_validate_parse() function to avoid code duplication.
Ultimately, this allows us to have very strict validation for every
new caller of nla_parse()/nlmsg_parse() etc as re-introduced in the
next patch, while existing things will continue to work as is.
In effect then, this adds fully strict validation for any new command.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Even if the NLA_F_NESTED flag was introduced more than 11 years ago, most
netlink based interfaces (including recently added ones) are still not
setting it in kernel generated messages. Without the flag, message parsers
not aware of attribute semantics (e.g. wireshark dissector or libmnl's
mnl_nlmsg_fprintf()) cannot recognize nested attributes and won't display
the structure of their contents.
Unfortunately we cannot just add the flag everywhere as there may be
userspace applications which check nlattr::nla_type directly rather than
through a helper masking out the flags. Therefore the patch renames
nla_nest_start() to nla_nest_start_noflag() and introduces nla_nest_start()
as a wrapper adding NLA_F_NESTED. The calls which add NLA_F_NESTED manually
are rewritten to use nla_nest_start().
Except for changes in include/net/netlink.h, the patch was generated using
this semantic patch:
@@ expression E1, E2; @@
-nla_nest_start(E1, E2)
+nla_nest_start_noflag(E1, E2)
@@ expression E1, E2; @@
-nla_nest_start_noflag(E1, E2 | NLA_F_NESTED)
+nla_nest_start(E1, E2)
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
I forgot to remove one rcu_read_unlock() before a return statement.
Joy of mixing goto and return styles in a function :)
Fixes: 4109a2c3b9 ("tipc: tipc_udp_recv() cleanup vs rcu verbs")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
First thing tipc_udp_recv() does is to use rcu_dereference_sk_user_data(),
and this is really hinting we already own rcu_read_lock() from the caller
(UDP stack).
No need to add another rcu_read_lock()/rcu_read_unlock() pair.
Also use rcu_dereference() instead of rcu_dereference_rtnl()
in the data path.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Jon Maloy <jon.maloy@ericsson.com>
Cc: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When using TIPC_SOCK_RECVQ_DEPTH for getsockopt(), it returns the
number of buffers in receive socket buffer which is not so helpful
for user space applications.
This commit introduces the new option TIPC_SOCK_RECVQ_USED which
returns the current allocated bytes of the receive socket buffer.
This helps user space applications dimension its buffer usage to
avoid buffer overload issue.
Signed-off-by: Tung Nguyen <tung.q.nguyen@dektech.com.au>
Acked-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We find that sysctl_tipc_rmem and named_timeout do not have the right minimum
setting. sysctl_tipc_rmem should be larger than zero, like sysctl_tcp_rmem.
And named_timeout as a timeout setting should be not less than zero.
Fixes: cc79dd1ba9 ("tipc: change socket buffer overflow control to respect sk_rcvbuf")
Fixes: a5325ae5b8 ("tipc: add name distributor resiliency queue")
Signed-off-by: Jie Liu <liujie165@huawei.com>
Reported-by: Qiang Ning <ningqiang1@huawei.com>
Reviewed-by: Zhiqiang Liu <liuzhiqiang26@huawei.com>
Reviewed-by: Miaohe Lin <linmiaohe@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
According to the link FSM, when a link endpoint got RESET_MSG (- a
traditional one without the stopping bit) from its peer, it moves to
PEER_RESET state and raises a LINK_DOWN event which then resets the
link itself. Its state will become ESTABLISHING after the reset event
and the link will be re-established soon after this endpoint starts to
send ACTIVATE_MSG to the peer.
There is no problem with this mechanism, however the link resetting has
cleared the link 'in_session' flag (along with the other important link
data such as: the link 'mtu') that was correctly set up at the 1st step
(i.e. when this endpoint received the peer RESET_MSG). As a result, the
link will become ESTABLISHED, but the 'in_session' flag is not set, and
all STATE_MSG from its peer will be dropped at the link_validate_msg().
It means the link not synced and will sooner or later face a failure.
Since the link reset action is obviously needed for a new link session
(this is also true in the other situations), the problem here is that
the link is re-established a bit too early when the link endpoints are
not really in-sync yet. The commit forces a resync as already done in
the previous commit 91986ee166 ("tipc: fix link session and
re-establish issues") by simply varying the link 'peer_session' value
at the link_reset().
Acked-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: Tuong Lien <tuong.t.lien@dektech.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the function tipc_node_create() we protect the peer capability field
by using the node rw_lock. However, we access the lock directly instead
of using the dedicated functions for this, as we do everywhere else in
node.c. This cosmetic spot is fixed here.
Fixes: 40999f11ce ("tipc: make link capability update thread safe")
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When binding multiple services with specific type 1Ki, 2Ki..,
this leads to some entries in the name table of publications
missing when listed out via 'tipc name show'.
The problem is at identify zero last_type conditional provided
via netlink. The first is initial 'type' when starting name table
dummping. The second is continuously with zero type (node state
service type). Then, lookup function failure to finding node state
service type in next iteration.
To solve this, adding more conditional to marked as dirty type and
lookup correct service type for the next iteration instead of select
the first service as initial 'type' zero.
Acked-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: Hoang Le <hoang.h.le@dektech.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Minor comment merge conflict in mlx5.
Staging driver has a fixup due to the skb->xmit_more changes
in 'net-next', but was removed in 'net'.
Signed-off-by: David S. Miller <davem@davemloft.net>
In commit 0ae955e2656d ("tipc: improve TIPC throughput by Gap ACK
blocks"), we enhance the link transmq by releasing as many packets as
possible with the multi-ACKs from peer node. This also means the queue
is now non-linear and the peer link deferdq becomes vital.
Whereas, in the case of link failover, all messages in the link transmq
need to be transmitted as tunnel messages in such a way that message
sequentiality and cardinality per sender is preserved. This requires us
to maintain the link deferdq somehow, so that when the tunnel messages
arrive, the inner user messages along with the ones in the deferdq will
be delivered to upper layer correctly.
The commit accomplishes this by defining a new queue in the TIPC link
structure to hold the old link deferdq when link failover happens and
process it upon receipt of tunnel messages.
Also, in the case of link syncing, the link deferdq will not be purged
to avoid unnecessary retransmissions that in the worst case will fail
because the packets might have been freed on the sending side.
Acked-by: Ying Xue <ying.xue@windriver.com>
Acked-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: Tuong Lien <tuong.t.lien@dektech.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
For unicast transmission, the current NACK sending althorithm is over-
active that forces the sending side to retransmit a packet that is not
really lost but just arrived at the receiving side with some delay, or
even retransmit same packets that have already been retransmitted
before. As a result, many duplicates are observed also under normal
condition, ie. without packet loss.
One example case is: node1 transmits 1 2 3 4 10 5 6 7 8 9, when node2
receives packet #10, it puts into the deferdq. When the packet #5 comes
it sends NACK with gap [6 - 9]. However, shortly after that, when
packet #6 arrives, it pulls out packet #10 from the deferfq, but it is
still out of order, so it makes another NACK with gap [7 - 9] and so on
... Finally, node1 has to retransmit the packets 5 6 7 8 9 a number of
times, but in fact all the packets are not lost at all, so duplicates!
This commit reduces duplicates by changing the condition to send NACK,
also restricting the retransmissions on individual packets via a timer
of about 1ms. However, it also needs to say that too tricky condition
for NACKs or too long timeout value for retransmissions will result in
performance reducing! The criterias in this commit are found to be
effective for both the requirements to reduce duplicates but not affect
performance.
The tipc_link_rcv() is also improved to only dequeue skb from the link
deferdq if it is expected (ie. its seqno <= rcv_nxt).
Acked-by: Ying Xue <ying.xue@windriver.com>
Acked-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: Tuong Lien <tuong.t.lien@dektech.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
During unicast link transmission, it's observed very often that because
of one or a few lost/dis-ordered packets, the sending side will fastly
reach the send window limit and must wait for the packets to be arrived
at the receiving side or in the worst case, a retransmission must be
done first. The sending side cannot release a lot of subsequent packets
in its transmq even though all of them might have already been received
by the receiving side.
That is, one or two packets dis-ordered/lost and dozens of packets have
to wait, this obviously reduces the overall throughput!
This commit introduces an algorithm to overcome this by using "Gap ACK
blocks". Basically, a Gap ACK block will consist of <ack, gap> numbers
that describes the link deferdq where packets have been got by the
receiving side but with gaps, for example:
link deferdq: [1 2 3 4 10 11 13 14 15 20]
--> Gap ACK blocks: <4, 5>, <11, 1>, <15, 4>, <20, 0>
The Gap ACK blocks will be sent to the sending side along with the
traditional ACK or NACK message. Immediately when receiving the message
the sending side will now not only release from its transmq the packets
ack-ed by the ACK but also by the Gap ACK blocks! So, more packets can
be enqueued and transmitted.
In addition, the sending side can now do "multi-retransmissions"
according to the Gaps reported in the Gap ACK blocks.
The new algorithm as verified helps greatly improve the TIPC throughput
especially under packet loss condition.
So far, a maximum of 32 blocks is quite enough without any "Too few Gap
ACK blocks" reports with a 5.0% packet loss rate, however this number
can be increased in the furture if needed.
Also, the patch is backward compatible.
Acked-by: Ying Xue <ying.xue@windriver.com>
Acked-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: Tuong Lien <tuong.t.lien@dektech.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
skb somehow dequeued out of inputq before processing, it causes to
NULL pointer and kernel crashed.
Add checking skb valid before using.
Fixes: c55c8edafa ("tipc: smooth change between replicast and broadcast")
Reported-by: Tuong Lien Tong <tuong.t.lien@dektech.com.au>
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Hoang Le <hoang.h.le@dektech.com.au>
Acked-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Syzbot found a crash:
BUG: KMSAN: uninit-value in tipc_nl_compat_name_table_dump+0x54f/0xcd0 net/tipc/netlink_compat.c:872
Call Trace:
tipc_nl_compat_name_table_dump+0x54f/0xcd0 net/tipc/netlink_compat.c:872
__tipc_nl_compat_dumpit+0x59e/0xda0 net/tipc/netlink_compat.c:215
tipc_nl_compat_dumpit+0x63a/0x820 net/tipc/netlink_compat.c:280
tipc_nl_compat_handle net/tipc/netlink_compat.c:1226 [inline]
tipc_nl_compat_recv+0x1b5f/0x2750 net/tipc/netlink_compat.c:1265
genl_family_rcv_msg net/netlink/genetlink.c:601 [inline]
genl_rcv_msg+0x185f/0x1a60 net/netlink/genetlink.c:626
netlink_rcv_skb+0x431/0x620 net/netlink/af_netlink.c:2477
genl_rcv+0x63/0x80 net/netlink/genetlink.c:637
netlink_unicast_kernel net/netlink/af_netlink.c:1310 [inline]
netlink_unicast+0xf3e/0x1020 net/netlink/af_netlink.c:1336
netlink_sendmsg+0x127f/0x1300 net/netlink/af_netlink.c:1917
sock_sendmsg_nosec net/socket.c:622 [inline]
sock_sendmsg net/socket.c:632 [inline]
Uninit was created at:
__alloc_skb+0x309/0xa20 net/core/skbuff.c:208
alloc_skb include/linux/skbuff.h:1012 [inline]
netlink_alloc_large_skb net/netlink/af_netlink.c:1182 [inline]
netlink_sendmsg+0xb82/0x1300 net/netlink/af_netlink.c:1892
sock_sendmsg_nosec net/socket.c:622 [inline]
sock_sendmsg net/socket.c:632 [inline]
It was supposed to be fixed on commit 974cb0e3e7 ("tipc: fix uninit-value
in tipc_nl_compat_name_table_dump") by checking TLV_GET_DATA_LEN(msg->req)
in cmd->header()/tipc_nl_compat_name_table_dump_header(), which is called
ahead of tipc_nl_compat_name_table_dump().
However, tipc_nl_compat_dumpit() doesn't handle the error returned from cmd
header function. It means even when the check added in that fix fails, it
won't stop calling tipc_nl_compat_name_table_dump(), and the issue will be
triggered again.
So this patch is to add the process for the err returned from cmd header
function in tipc_nl_compat_dumpit().
Reported-by: syzbot+3ce8520484b0d4e260a5@syzkaller.appspotmail.com
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A similar issue as fixed by Patch "tipc: check bearer name with right
length in tipc_nl_compat_bearer_enable" was also found by syzbot in
tipc_nl_compat_link_set().
The length to check with should be 'TLV_GET_DATA_LEN(msg->req) -
offsetof(struct tipc_link_config, name)'.
Reported-by: syzbot+de00a87b8644a582ae79@syzkaller.appspotmail.com
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Syzbot reported the following crash:
BUG: KMSAN: uninit-value in memchr+0xce/0x110 lib/string.c:961
memchr+0xce/0x110 lib/string.c:961
string_is_valid net/tipc/netlink_compat.c:176 [inline]
tipc_nl_compat_bearer_enable+0x2c4/0x910 net/tipc/netlink_compat.c:401
__tipc_nl_compat_doit net/tipc/netlink_compat.c:321 [inline]
tipc_nl_compat_doit+0x3aa/0xaf0 net/tipc/netlink_compat.c:354
tipc_nl_compat_handle net/tipc/netlink_compat.c:1162 [inline]
tipc_nl_compat_recv+0x1ae7/0x2750 net/tipc/netlink_compat.c:1265
genl_family_rcv_msg net/netlink/genetlink.c:601 [inline]
genl_rcv_msg+0x185f/0x1a60 net/netlink/genetlink.c:626
netlink_rcv_skb+0x431/0x620 net/netlink/af_netlink.c:2477
genl_rcv+0x63/0x80 net/netlink/genetlink.c:637
netlink_unicast_kernel net/netlink/af_netlink.c:1310 [inline]
netlink_unicast+0xf3e/0x1020 net/netlink/af_netlink.c:1336
netlink_sendmsg+0x127f/0x1300 net/netlink/af_netlink.c:1917
sock_sendmsg_nosec net/socket.c:622 [inline]
sock_sendmsg net/socket.c:632 [inline]
Uninit was created at:
__alloc_skb+0x309/0xa20 net/core/skbuff.c:208
alloc_skb include/linux/skbuff.h:1012 [inline]
netlink_alloc_large_skb net/netlink/af_netlink.c:1182 [inline]
netlink_sendmsg+0xb82/0x1300 net/netlink/af_netlink.c:1892
sock_sendmsg_nosec net/socket.c:622 [inline]
sock_sendmsg net/socket.c:632 [inline]
It was triggered when the bearer name size < TIPC_MAX_BEARER_NAME,
it would check with a wrong len/TLV_GET_DATA_LEN(msg->req), which
also includes priority and disc_domain length.
This patch is to fix it by checking it with a right length:
'TLV_GET_DATA_LEN(msg->req) - offsetof(struct tipc_bearer_config, name)'.
Reported-by: syzbot+8b707430713eb46e1e45@syzkaller.appspotmail.com
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The number of stubs is growing and has nothing to do with addrconf.
Move the definition of the stubs to a separate header file and update
users. In the move, drop the vxlan specific comment before ipv6_stub.
Code move only; no functional change intended.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix the return value check which testing the wrong variable
in tipc_mcast_send_sync().
Fixes: c55c8edafa ("tipc: smooth change between replicast and broadcast")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Acked-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When running a syz script, a panic occurred:
[ 156.088228] BUG: KASAN: use-after-free in tipc_disc_timeout+0x9c9/0xb20 [tipc]
[ 156.094315] Call Trace:
[ 156.094844] <IRQ>
[ 156.095306] dump_stack+0x7c/0xc0
[ 156.097346] print_address_description+0x65/0x22e
[ 156.100445] kasan_report.cold.3+0x37/0x7a
[ 156.102402] tipc_disc_timeout+0x9c9/0xb20 [tipc]
[ 156.106517] call_timer_fn+0x19a/0x610
[ 156.112749] run_timer_softirq+0xb51/0x1090
It was caused by the netns freed without deleting the discoverer timer,
while later on the netns would be accessed in the timer handler.
The timer should have been deleted by tipc_net_stop() when cleaning up a
netns. However, tipc has been able to enable a bearer and start d->timer
without the local node_addr set since Commit 52dfae5c85 ("tipc: obtain
node identity from interface by default"), which caused the timer not to
be deleted in tipc_net_stop() then.
So fix it in tipc_net_stop() by changing to check local node_id instead
of local node_addr, as Jon suggested.
While at it, remove the calling of tipc_nametbl_withdraw() there, since
tipc_nametbl_stop() will take of the nametbl's freeing after.
Fixes: 52dfae5c85 ("tipc: obtain node identity from interface by default")
Reported-by: syzbot+a25307ad099309f1c2b9@syzkaller.appspotmail.com
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Ying Xue <ying.xue@windriver.com>
Acked-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When checking the code with clang -Wsometimes-uninitialized we get the
following warning:
if (!tipc_link_is_establishing(l)) {
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~
net/tipc/node.c:847:46: note: uninitialized use occurs here
tipc_bearer_xmit(n->net, bearer_id, &xmitq, maddr);
net/tipc/node.c:831:2: note: remove the 'if' if its condition is always
true
if (!tipc_link_is_establishing(l)) {
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
net/tipc/node.c:821:31: note: initialize the variable 'maddr' to silence
this warning
struct tipc_media_addr *maddr;
We fix this by initializing 'maddr' to NULL. For the matter of clarity,
we also test if 'xmitq' is non-empty before we use it and 'maddr'
further down in the function. It will never happen that 'xmitq' is non-
empty at the same time as 'maddr' is NULL, so this is a sufficient test.
Fixes: 598411d70f ("tipc: make resetting of links non-atomic")
Reported-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since maxattr is common, the policy can't really differ sanely,
so make it common as well.
The only user that did in fact manage to make a non-common policy
is taskstats, which has to be really careful about it (since it's
still using a common maxattr!). This is no longer supported, but
we can fake it using pre_doit.
This reduces the size of e.g. nl80211.o (which has lots of commands):
text data bss dec hex filename
398745 14323 2240 415308 6564c net/wireless/nl80211.o (before)
397913 14331 2240 414484 65314 net/wireless/nl80211.o (after)
--------------------------------
-832 +8 0 -824
Which is obviously just 8 bytes for each command, and an added 8
bytes for the new policy pointer. I'm not sure why the ops list is
counted as .text though.
Most of the code transformations were done using the following spatch:
@ops@
identifier OPS;
expression POLICY;
@@
struct genl_ops OPS[] = {
...,
{
- .policy = POLICY,
},
...
};
@@
identifier ops.OPS;
expression ops.POLICY;
identifier fam;
expression M;
@@
struct genl_family fam = {
.ops = OPS,
.maxattr = M,
+ .policy = POLICY,
...
};
This also gets rid of devlink_nl_cmd_region_read_dumpit() accessing
the cb->data as ops, which we want to change in a later genl patch.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
skb free-ed in:
1/ condition 1: tipc_sk_filter_rcv -> tipc_sk_proto_rcv
2/ condition 2: tipc_sk_filter_rcv -> tipc_group_filter_msg
This leads to a "use-after-free" access in the next condition.
We fix this by intializing the variable at declaration, then it is safe
to check this variable to continue processing if condition matches.
syzbot report:
==================================================================
BUG: KASAN: use-after-free in tipc_sk_filter_rcv+0x2166/0x34f0
net/tipc/socket.c:2167
Read of size 4 at addr ffff88808ea58534 by task kworker/u4:0/7
CPU: 0 PID: 7 Comm: kworker/u4:0 Not tainted 5.0.0+ #61
Hardware name: Google Google Compute Engine/Google Compute Engine,
BIOS Google 01/01/2011
Workqueue: tipc_send tipc_conn_send_work
Call Trace:
__dump_stack lib/dump_stack.c:77 [inline]
dump_stack+0x172/0x1f0 lib/dump_stack.c:113
print_address_description.cold+0x7c/0x20d mm/kasan/report.c:187
kasan_report.cold+0x1b/0x40 mm/kasan/report.c:317
__asan_report_load4_noabort+0x14/0x20 mm/kasan/generic_report.c:131
tipc_sk_filter_rcv+0x2166/0x34f0 net/tipc/socket.c:2167
tipc_sk_enqueue net/tipc/socket.c:2254 [inline]
tipc_sk_rcv+0xc45/0x25a0 net/tipc/socket.c:2305
tipc_topsrv_kern_evt+0x3b7/0x580 net/tipc/topsrv.c:610
tipc_conn_send_to_sock+0x43e/0x5f0 net/tipc/topsrv.c:283
tipc_conn_send_work+0x65/0x80 net/tipc/topsrv.c:303
process_one_work+0x98e/0x1790 kernel/workqueue.c:2269
worker_thread+0x98/0xe40 kernel/workqueue.c:2415
kthread+0x357/0x430 kernel/kthread.c:253
ret_from_fork+0x3a/0x50 arch/x86/entry/entry_64.S:352
Reported-by: syzbot+e863893591cc7a622e40@syzkaller.appspotmail.com
Fixes: c55c8eda ("tipc: smooth change between replicast and broadcast")
Acked-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: Hoang Le <hoang.h.le@dektech.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
When cancelling a subscription, we have to clear the cancel bit in the
request before iterating over any established subscriptions with memcmp.
Otherwise no subscription will ever be found, and it will not be
possible to explicitly unsubscribe individual subscriptions.
Fixes: 8985ecc7c1 ("tipc: simplify endianness handling in topology subscriber")
Signed-off-by: Erik Hugne <erik.hugne@gmail.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, a multicast stream may start out using replicast, because
there are few destinations, and then it should ideally switch to
L2/broadcast IGMP/multicast when the number of destinations grows beyond
a certain limit. The opposite should happen when the number decreases
below the limit.
To eliminate the risk of message reordering caused by method change,
a sending socket must stick to a previously selected method until it
enters an idle period of 5 seconds. Means there is a 5 seconds pause
in the traffic from the sender socket.
If the sender never makes such a pause, the method will never change,
and transmission may become very inefficient as the cluster grows.
With this commit, we allow such a switch between replicast and
broadcast without any need for a traffic pause.
Solution is to send a dummy message with only the header, also with
the SYN bit set, via broadcast or replicast. For the data message,
the SYN bit is set and sending via replicast or broadcast (inverse
method with dummy).
Then, at receiving side any messages follow first SYN bit message
(data or dummy message), they will be held in deferred queue until
another pair (dummy or data message) arrived in other link.
v2: reverse christmas tree declaration
Acked-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: Hoang Le <hoang.h.le@dektech.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
As a preparation for introducing a smooth switching between replicast
and broadcast method for multicast message, We have to introduce a new
capability flag TIPC_MCAST_RBCTL to handle this new feature.
During a cluster upgrade a node can come back with this new capabilities
which also must be reflected in the cluster capabilities field.
The new feature is only applicable if all node in the cluster supports
this new capability.
Acked-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: Hoang Le <hoang.h.le@dektech.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, a multicast stream uses either broadcast or replicast as
transmission method, based on the ratio between number of actual
destinations nodes and cluster size.
However, when an L2 interface (e.g., VXLAN) provides pseudo
broadcast support, this becomes very inefficient, as it blindly
replicates multicast packets to all cluster/subnet nodes,
irrespective of whether they host actual target sockets or not.
The TIPC multicast algorithm is able to distinguish real destination
nodes from other nodes, and hence provides a smarter and more
efficient method for transferring multicast messages than
pseudo broadcast can do.
Because of this, we now make it possible for users to force
the broadcast link to permanently switch to using replicast,
irrespective of which capabilities the bearer provides,
or pretend to provide.
Conversely, we also make it possible to force the broadcast link
to always use true broadcast. While maybe less useful in
deployed systems, this may at least be useful for testing the
broadcast algorithm in small clusters.
We retain the current AUTOSELECT ability, i.e., to let the broadcast link
automatically select which algorithm to use, and to switch back and forth
between broadcast and replicast as the ratio between destination
node number and cluster size changes. This remains the default method.
Furthermore, we make it possible to configure the threshold ratio for
such switches. The default ratio is now set to 10%, down from 25% in the
earlier implementation.
Acked-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: Hoang Le <hoang.h.le@dektech.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
We move the check that prevents connecting service ranges to after
the RDM/DGRAM check, and move address sanity control to a separate
function that also validates the service range.
Fixes: 23998835be ("tipc: improve address sanity check in tipc_connect()")
Signed-off-by: Erik Hugne <erik.hugne@gmail.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
nla_nest_start may fail. The fix check its status and returns
-EMSGSIZE in case it fails.
Signed-off-by: Kangjie Lu <kjlu@umn.edu>
Signed-off-by: David S. Miller <davem@davemloft.net>
nla_nest_start could fail and requires a check. The fix returns
-EMSGSIZE if it fails.
Signed-off-by: Kangjie Lu <kjlu@umn.edu>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix regression bug introduced in
commit 365ad353c2 ("tipc: reduce risk of user starvation during link
congestion")
Only signal -EDESTADDRREQ for RDM/DGRAM if we don't have a cached
sockaddr.
Fixes: 365ad353c2 ("tipc: reduce risk of user starvation during link congestion")
Signed-off-by: Erik Hugne <erik.hugne@gmail.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When sending multicast messages via blocking socket,
if sending link is congested (tsk->cong_link_cnt is set to 1),
the sending thread will be put into sleeping state. However,
tipc_sk_filter_rcv() is called under socket spin lock but
tipc_wait_for_cond() is not. So, there is no guarantee that
the setting of tsk->cong_link_cnt to 0 in tipc_sk_proto_rcv() in
CPU-1 will be perceived by CPU-0. If that is the case, the sending
thread in CPU-0 after being waken up, will continue to see
tsk->cong_link_cnt as 1 and put the sending thread into sleeping
state again. The sending thread will sleep forever.
CPU-0 | CPU-1
tipc_wait_for_cond() |
{ |
// condition_ = !tsk->cong_link_cnt |
while ((rc_ = !(condition_))) { |
... |
release_sock(sk_); |
wait_woken(); |
| if (!sock_owned_by_user(sk))
| tipc_sk_filter_rcv()
| {
| ...
| tipc_sk_proto_rcv()
| {
| ...
| tsk->cong_link_cnt--;
| ...
| sk->sk_write_space(sk);
| ...
| }
| ...
| }
sched_annotate_sleep(); |
lock_sock(sk_); |
remove_wait_queue(); |
} |
} |
This commit fixes it by adding memory barrier to tipc_sk_proto_rcv()
and tipc_wait_for_cond().
Acked-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: Tung Nguyen <tung.q.nguyen@dektech.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Three conflicts, one of which, for marvell10g.c is non-trivial and
requires some follow-up from Heiner or someone else.
The issue is that Heiner converted the marvell10g driver over to
use the generic c45 code as much as possible.
However, in 'net' a bug fix appeared which makes sure that a new
local mask (MDIO_AN_10GBT_CTRL_ADV_NBT_MASK) with value 0x01e0
is cleared.
Signed-off-by: David S. Miller <davem@davemloft.net>
This commit replaces schedule_timeout() with wait_woken()
in function tipc_wait_for_rcvmsg(). wait_woken() uses
memory barriers in its implementation to avoid potential
race condition when putting a process into sleeping state
and then waking it up.
Acked-by: Ying Xue <ying.xue@windriver.com>
Acked-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: Tung Nguyen <tung.q.nguyen@dektech.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 844cf763fb ("tipc: make macro tipc_wait_for_cond() smp safe")
replaced finish_wait() with remove_wait_queue() but still used
prepare_to_wait(). This causes unnecessary conditional
checking before adding to wait queue in prepare_to_wait().
This commit replaces prepare_to_wait() with add_wait_queue()
as the pair function with remove_wait_queue().
Acked-by: Ying Xue <ying.xue@windriver.com>
Acked-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: Tung Nguyen <tung.q.nguyen@dektech.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
The netfilter conflicts were rather simple overlapping
changes.
However, the cls_tcindex.c stuff was a bit more complex.
On the 'net' side, Cong is fixing several races and memory
leaks. Whilst on the 'net-next' side we have Vlad adding
the rtnl-ness support.
What I've decided to do, in order to resolve this, is revert the
conversion over to using a workqueue that Cong did, bringing us back
to pure RCU. I did it this way because I believe that either Cong's
races don't apply with have Vlad did things, or Cong will have to
implement the race fix slightly differently.
Signed-off-by: David S. Miller <davem@davemloft.net>
When a link endpoint is re-created (e.g. after a node reboot or
interface reset), the link session number is varied by random, the peer
endpoint will be synced with this new session number before the link is
re-established.
However, there is a shortcoming in this mechanism that can lead to the
link never re-established or faced with a failure then. It happens when
the peer endpoint is ready in ESTABLISHING state, the 'peer_session' as
well as the 'in_session' flag have been set, but suddenly this link
endpoint leaves. When it comes back with a random session number, there
are two situations possible:
1/ If the random session number is larger than (or equal to) the
previous one, the peer endpoint will be updated with this new session
upon receipt of a RESET_MSG from this endpoint, and the link can be re-
established as normal. Otherwise, all the RESET_MSGs from this endpoint
will be rejected by the peer. In turn, when this link endpoint receives
one ACTIVATE_MSG from the peer, it will move to ESTABLISHED and start
to send STATE_MSGs, but again these messages will be dropped by the
peer due to wrong session.
The peer link endpoint can still become ESTABLISHED after receiving a
traffic message from this endpoint (e.g. a BCAST_PROTOCOL or
NAME_DISTRIBUTOR), but since all the STATE_MSGs are invalid, the link
will be forced down sooner or later!
Even in case the random session number is larger than the previous one,
it can be that the ACTIVATE_MSG from the peer arrives first, and this
link endpoint moves quickly to ESTABLISHED without sending out any
RESET_MSG yet. Consequently, the peer link will not be updated with the
new session number, and the same link failure scenario as above will
happen.
2/ Another situation can be that, the peer link endpoint was reset due
to any reasons in the meantime, its link state was set to RESET from
ESTABLISHING but still in session, i.e. the 'in_session' flag is not
reset...
Now, if the random session number from this endpoint is less than the
previous one, all the RESET_MSGs from this endpoint will be rejected by
the peer. In the other direction, when this link endpoint receives a
RESET_MSG from the peer, it moves to ESTABLISHING and starts to send
ACTIVATE_MSGs, but all these messages will be rejected by the peer too.
As a result, the link cannot be re-established but gets stuck with this
link endpoint in state ESTABLISHING and the peer in RESET!
Solution:
===========
This link endpoint should not go directly to ESTABLISHED when getting
ACTIVATE_MSG from the peer which may belong to the old session if the
link was re-created. To ensure the session to be correct before the
link is re-established, the peer endpoint in ESTABLISHING state will
send back the last session number in ACTIVATE_MSG for a verification at
this endpoint. Then, if needed, a new and more appropriate session
number will be regenerated to force a re-synch first.
In addition, when a link in ESTABLISHING state is reset, its state will
move to RESET according to the link FSM, along with resetting the
'in_session' flag (and the other data) as a normal link reset, it will
also be deleted if requested.
The solution is backward compatible.
Acked-by: Jon Maloy <jon.maloy@ericsson.com>
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Tuong Lien <tuong.t.lien@dektech.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
When we free skb at tipc_data_input, we return a 'false' boolean.
Then, skb passed to subcalling tipc_link_input in tipc_link_rcv,
<snip>
1303 int tipc_link_rcv:
...
1354 if (!tipc_data_input(l, skb, l->inputq))
1355 rc |= tipc_link_input(l, skb, l->inputq);
</snip>
Fix it by simple changing to a 'true' boolean when skb is being free-ed.
Then, tipc_link_rcv will bypassed to subcalling tipc_link_input as above
condition.
Acked-by: Ying Xue <ying.xue@windriver.com>
Acked-by: Jon Maloy <maloy@donjonn.com>
Signed-off-by: Hoang Le <hoang.h.le@dektech.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
max_rcvbuf_size is no longer used since commit "414574a0af36".
Signed-off-by: Zhaolong Zhang <zhangzl2013@126.com>
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
This patch fixes the following warnings:
net/tipc/link.c:1125:6: warning: this statement may fall through [-Wimplicit-fallthrough=]
net/tipc/socket.c:736:6: warning: this statement may fall through [-Wimplicit-fallthrough=]
net/tipc/socket.c:2418:7: warning: this statement may fall through [-Wimplicit-fallthrough=]
Warning level 3 was used: -Wimplicit-fallthrough=3
This patch is part of the ongoing efforts to enabling
-Wimplicit-fallthrough.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
BUG: KMSAN: uninit-value in tipc_nl_compat_doit+0x404/0xa10 net/tipc/netlink_compat.c:335
CPU: 0 PID: 4514 Comm: syz-executor485 Not tainted 4.16.0+ #87
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Call Trace:
__dump_stack lib/dump_stack.c:17 [inline]
dump_stack+0x185/0x1d0 lib/dump_stack.c:53
kmsan_report+0x142/0x240 mm/kmsan/kmsan.c:1067
__msan_warning_32+0x6c/0xb0 mm/kmsan/kmsan_instr.c:683
tipc_nl_compat_doit+0x404/0xa10 net/tipc/netlink_compat.c:335
tipc_nl_compat_recv+0x164b/0x2700 net/tipc/netlink_compat.c:1153
genl_family_rcv_msg net/netlink/genetlink.c:599 [inline]
genl_rcv_msg+0x1686/0x1810 net/netlink/genetlink.c:624
netlink_rcv_skb+0x378/0x600 net/netlink/af_netlink.c:2447
genl_rcv+0x63/0x80 net/netlink/genetlink.c:635
netlink_unicast_kernel net/netlink/af_netlink.c:1311 [inline]
netlink_unicast+0x166b/0x1740 net/netlink/af_netlink.c:1337
netlink_sendmsg+0x1048/0x1310 net/netlink/af_netlink.c:1900
sock_sendmsg_nosec net/socket.c:630 [inline]
sock_sendmsg net/socket.c:640 [inline]
___sys_sendmsg+0xec0/0x1310 net/socket.c:2046
__sys_sendmsg net/socket.c:2080 [inline]
SYSC_sendmsg+0x2a3/0x3d0 net/socket.c:2091
SyS_sendmsg+0x54/0x80 net/socket.c:2087
do_syscall_64+0x309/0x430 arch/x86/entry/common.c:287
entry_SYSCALL_64_after_hwframe+0x3d/0xa2
RIP: 0033:0x43fda9
RSP: 002b:00007ffd0c184ba8 EFLAGS: 00000213 ORIG_RAX: 000000000000002e
RAX: ffffffffffffffda RBX: 00000000004002c8 RCX: 000000000043fda9
RDX: 0000000000000000 RSI: 0000000020023000 RDI: 0000000000000003
RBP: 00000000006ca018 R08: 00000000004002c8 R09: 00000000004002c8
R10: 00000000004002c8 R11: 0000000000000213 R12: 00000000004016d0
R13: 0000000000401760 R14: 0000000000000000 R15: 0000000000000000
Uninit was created at:
kmsan_save_stack_with_flags mm/kmsan/kmsan.c:278 [inline]
kmsan_internal_poison_shadow+0xb8/0x1b0 mm/kmsan/kmsan.c:188
kmsan_kmalloc+0x94/0x100 mm/kmsan/kmsan.c:314
kmsan_slab_alloc+0x11/0x20 mm/kmsan/kmsan.c:321
slab_post_alloc_hook mm/slab.h:445 [inline]
slab_alloc_node mm/slub.c:2737 [inline]
__kmalloc_node_track_caller+0xaed/0x11c0 mm/slub.c:4369
__kmalloc_reserve net/core/skbuff.c:138 [inline]
__alloc_skb+0x2cf/0x9f0 net/core/skbuff.c:206
alloc_skb include/linux/skbuff.h:984 [inline]
netlink_alloc_large_skb net/netlink/af_netlink.c:1183 [inline]
netlink_sendmsg+0x9a6/0x1310 net/netlink/af_netlink.c:1875
sock_sendmsg_nosec net/socket.c:630 [inline]
sock_sendmsg net/socket.c:640 [inline]
___sys_sendmsg+0xec0/0x1310 net/socket.c:2046
__sys_sendmsg net/socket.c:2080 [inline]
SYSC_sendmsg+0x2a3/0x3d0 net/socket.c:2091
SyS_sendmsg+0x54/0x80 net/socket.c:2087
do_syscall_64+0x309/0x430 arch/x86/entry/common.c:287
entry_SYSCALL_64_after_hwframe+0x3d/0xa2
In tipc_nl_compat_recv(), when the len variable returned by
nlmsg_attrlen() is 0, the message is still treated as a valid one,
which is obviously unresonable. When len is zero, it means the
message not only doesn't contain any valid TLV payload, but also
TLV header is not included. Under this stituation, tlv_type field
in TLV header is still accessed in tipc_nl_compat_dumpit() or
tipc_nl_compat_doit(), but the field space is obviously illegal.
Of course, it is not initialized.
Reported-by: syzbot+bca0dc46634781f08b38@syzkaller.appspotmail.com
Reported-by: syzbot+6bdb590321a7ae40c1a6@syzkaller.appspotmail.com
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
syzbot reported:
BUG: KMSAN: uninit-value in tipc_conn_rcv_sub+0x184/0x950 net/tipc/topsrv.c:373
CPU: 0 PID: 66 Comm: kworker/u4:4 Not tainted 4.17.0-rc3+ #88
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Workqueue: tipc_rcv tipc_conn_recv_work
Call Trace:
__dump_stack lib/dump_stack.c:77 [inline]
dump_stack+0x185/0x1d0 lib/dump_stack.c:113
kmsan_report+0x142/0x240 mm/kmsan/kmsan.c:1067
__msan_warning_32+0x6c/0xb0 mm/kmsan/kmsan_instr.c:683
tipc_conn_rcv_sub+0x184/0x950 net/tipc/topsrv.c:373
tipc_conn_rcv_from_sock net/tipc/topsrv.c:409 [inline]
tipc_conn_recv_work+0x3cd/0x560 net/tipc/topsrv.c:424
process_one_work+0x12c6/0x1f60 kernel/workqueue.c:2145
worker_thread+0x113c/0x24f0 kernel/workqueue.c:2279
kthread+0x539/0x720 kernel/kthread.c:239
ret_from_fork+0x35/0x40 arch/x86/entry/entry_64.S:412
Local variable description: ----s.i@tipc_conn_recv_work
Variable was created at:
tipc_conn_recv_work+0x65/0x560 net/tipc/topsrv.c:419
process_one_work+0x12c6/0x1f60 kernel/workqueue.c:2145
In tipc_conn_rcv_from_sock(), it always supposes the length of message
received from sock_recvmsg() is not smaller than the size of struct
tipc_subscr. However, this assumption is false. Especially when the
length of received message is shorter than struct tipc_subscr size,
we will end up touching uninitialized fields in tipc_conn_rcv_sub().
Reported-by: syzbot+8951a3065ee7fd6d6e23@syzkaller.appspotmail.com
Reported-by: syzbot+75e6e042c5bbf691fc82@syzkaller.appspotmail.com
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a memory leak in case genlmsg_put fails.
Fix this by freeing *args* before return.
Addresses-Coverity-ID: 1476406 ("Resource leak")
Fixes: 46273cf7e0 ("tipc: fix a missing check of genlmsg_put")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
genlmsg_put could fail. The fix inserts a check of its return value, and
if it fails, returns -EMSGSIZE.
Signed-off-by: Kangjie Lu <kjlu@umn.edu>
Signed-off-by: David S. Miller <davem@davemloft.net>
bearer_disable() already calls kfree_rcu() to free struct tipc_bearer,
we don't need to call kfree() again.
Fixes: cb30a63384 ("tipc: refactor function tipc_enable_bearer()")
Reported-by: syzbot+b981acf1fb240c0c128b@syzkaller.appspotmail.com
Cc: Ying Xue <ying.xue@windriver.com>
Cc: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In tipc_nl_compat_sk_dump(), if nla_parse_nested() fails, it could return
an error. To be consistent with other invocations of the function call,
on error, the fix passes the return value upstream.
Signed-off-by: Aditya Pakki <pakki001@umn.edu>
Signed-off-by: David S. Miller <davem@davemloft.net>
Lots of conflicts, by happily all cases of overlapping
changes, parallel adds, things of that nature.
Thanks to Stephen Rothwell, Saeed Mahameed, and others
for their guidance in these resolutions.
Signed-off-by: David S. Miller <davem@davemloft.net>
When sending broadcast message on high load system, there are a lot of
unnecessary packets restranmission. That issue was caused by missing in
initial criteria for retransmission.
To prevent this happen, just initialize this criteria for retransmission
in next 10 milliseconds.
Fixes: 31c4f4cc32 ("tipc: improve broadcast retransmission algorithm")
Acked-by: Ying Xue <ying.xue@windriver.com>
Acked-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: Hoang Le <hoang.h.le@dektech.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
The commit adds the new trace_event for TIPC bearer, L2 device event:
trace_tipc_l2_device_event()
Also, it puts the trace at the tipc_l2_device_event() function, then
the device/bearer events and related info can be traced out during
runtime when needed.
Acked-by: Ying Xue <ying.xue@windriver.com>
Tested-by: Ying Xue <ying.xue@windriver.com>
Acked-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: Tuong Lien <tuong.t.lien@dektech.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
The commit adds the new trace_events for TIPC node object:
trace_tipc_node_create()
trace_tipc_node_delete()
trace_tipc_node_lost_contact()
trace_tipc_node_timeout()
trace_tipc_node_link_up()
trace_tipc_node_link_down()
trace_tipc_node_reset_links()
trace_tipc_node_fsm_evt()
trace_tipc_node_check_state()
Also, enables the traces for the following cases:
- When a node is created/deleted;
- When a node contact is lost;
- When a node timer is timed out;
- When a node link is up/down;
- When all node links are reset;
- When node state is changed;
- When a skb comes and node state needs to be checked/updated.
Acked-by: Ying Xue <ying.xue@windriver.com>
Tested-by: Ying Xue <ying.xue@windriver.com>
Acked-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: Tuong Lien <tuong.t.lien@dektech.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
The commit adds the new trace_events for TIPC socket object:
trace_tipc_sk_create()
trace_tipc_sk_poll()
trace_tipc_sk_sendmsg()
trace_tipc_sk_sendmcast()
trace_tipc_sk_sendstream()
trace_tipc_sk_filter_rcv()
trace_tipc_sk_advance_rx()
trace_tipc_sk_rej_msg()
trace_tipc_sk_drop_msg()
trace_tipc_sk_release()
trace_tipc_sk_shutdown()
trace_tipc_sk_overlimit1()
trace_tipc_sk_overlimit2()
Also, enables the traces for the following cases:
- When user creates a TIPC socket;
- When user calls poll() on TIPC socket;
- When user sends a dgram/mcast/stream message.
- When a message is put into the socket 'sk_receive_queue';
- When a message is released from the socket 'sk_receive_queue';
- When a message is rejected (e.g. due to no port, invalid, etc.);
- When a message is dropped (e.g. due to wrong message type);
- When socket is released;
- When socket is shutdown;
- When socket rcvq's allocation is overlimit (> 90%);
- When socket rcvq + bklq's allocation is overlimit (> 90%);
- When the 'TIPC_ERR_OVERLOAD/2' issue happens;
Note:
a) All the socket traces are designed to be able to trace on a specific
socket by either using the 'event filtering' feature on a known socket
'portid' value or the sysctl file:
/proc/sys/net/tipc/sk_filter
The file determines a 'tuple' for what socket should be traced:
(portid, sock type, name type, name lower, name upper)
where:
+ 'portid' is the socket portid generated at socket creating, can be
found in the trace outputs or the 'tipc socket list' command printouts;
+ 'sock type' is the socket type (1 = SOCK_TREAM, ...);
+ 'name type', 'name lower' and 'name upper' are the service name being
connected to or published by the socket.
Value '0' means 'ANY', the default tuple value is (0, 0, 0, 0, 0) i.e.
the traces happen for every sockets with no filter.
b) The 'tipc_sk_overlimit1/2' event is also a conditional trace_event
which happens when the socket receive queue (and backlog queue) is
about to be overloaded, when the queue allocation is > 90%. Then, when
the trace is enabled, the last skbs leading to the TIPC_ERR_OVERLOAD/2
issue can be traced.
The trace event is designed as an 'upper watermark' notification that
the other traces (e.g. 'tipc_sk_advance_rx' vs 'tipc_sk_filter_rcv') or
actions can be triggerred in the meanwhile to see what is going on with
the socket queue.
In addition, the 'trace_tipc_sk_dump()' is also placed at the
'TIPC_ERR_OVERLOAD/2' case, so the socket and last skb can be dumped
for post-analysis.
Acked-by: Ying Xue <ying.xue@windriver.com>
Tested-by: Ying Xue <ying.xue@windriver.com>
Acked-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: Tuong Lien <tuong.t.lien@dektech.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
The commit adds the new trace_events for TIPC link object:
trace_tipc_link_timeout()
trace_tipc_link_fsm()
trace_tipc_link_reset()
trace_tipc_link_too_silent()
trace_tipc_link_retrans()
trace_tipc_link_bc_ack()
trace_tipc_link_conges()
And the traces for PROTOCOL messages at building and receiving:
trace_tipc_proto_build()
trace_tipc_proto_rcv()
Note:
a) The 'tipc_link_too_silent' event will only happen when the
'silent_intv_cnt' is about to reach the 'abort_limit' value (and the
event is enabled). The benefit for this kind of event is that we can
get an early indication about TIPC link loss issue due to timeout, then
can do some necessary actions for troubleshooting.
For example: To trigger the 'tipc_proto_rcv' when the 'too_silent'
event occurs:
echo 'enable_event:tipc:tipc_proto_rcv' > \
events/tipc/tipc_link_too_silent/trigger
And disable it when TIPC link is reset:
echo 'disable_event:tipc:tipc_proto_rcv' > \
events/tipc/tipc_link_reset/trigger
b) The 'tipc_link_retrans' or 'tipc_link_bc_ack' event is useful to
trace TIPC retransmission issues.
In addition, the commit adds the 'trace_tipc_list/link_dump()' at the
'retransmission failure' case. Then, if the issue occurs, the link
'transmq' along with the link data can be dumped for post-analysis.
These dump events should be enabled by default since it will only take
effect when the failure happens.
The same approach is also applied for the faulty case that the
validation of protocol message is failed.
Acked-by: Ying Xue <ying.xue@windriver.com>
Tested-by: Ying Xue <ying.xue@windriver.com>
Acked-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: Tuong Lien <tuong.t.lien@dektech.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
As for the sake of debugging/tracing, the commit enables tracepoints in
TIPC along with some general trace_events as shown below. It also
defines some 'tipc_*_dump()' functions that allow to dump TIPC object
data whenever needed, that is, for general debug purposes, ie. not just
for the trace_events.
The following trace_events are now available:
- trace_tipc_skb_dump(): allows to trace and dump TIPC msg & skb data,
e.g. message type, user, droppable, skb truesize, cloned skb, etc.
- trace_tipc_list_dump(): allows to trace and dump any TIPC buffers or
queues, e.g. TIPC link transmq, socket receive queue, etc.
- trace_tipc_sk_dump(): allows to trace and dump TIPC socket data, e.g.
sk state, sk type, connection type, rmem_alloc, socket queues, etc.
- trace_tipc_link_dump(): allows to trace and dump TIPC link data, e.g.
link state, silent_intv_cnt, gap, bc_gap, link queues, etc.
- trace_tipc_node_dump(): allows to trace and dump TIPC node data, e.g.
node state, active links, capabilities, link entries, etc.
How to use:
Put the trace functions at any places where we want to dump TIPC data
or events.
Note:
a) The dump functions will generate raw data only, that is, to offload
the trace event's processing, it can require a tool or script to parse
the data but this should be simple.
b) The trace_tipc_*_dump() should be reserved for a failure cases only
(e.g. the retransmission failure case) or where we do not expect to
happen too often, then we can consider enabling these events by default
since they will almost not take any effects under normal conditions,
but once the rare condition or failure occurs, we get the dumped data
fully for post-analysis.
For other trace purposes, we can reuse these trace classes as template
but different events.
c) A trace_event is only effective when we enable it. To enable the
TIPC trace_events, echo 1 to 'enable' files in the events/tipc/
directory in the 'debugfs' file system. Normally, they are located at:
/sys/kernel/debug/tracing/events/tipc/
For example:
To enable the tipc_link_dump event:
echo 1 > /sys/kernel/debug/tracing/events/tipc/tipc_link_dump/enable
To enable all the TIPC trace_events:
echo 1 > /sys/kernel/debug/tracing/events/tipc/enable
To collect the trace data:
cat trace
or
cat trace_pipe > /trace.out &
To disable all the TIPC trace_events:
echo 0 > /sys/kernel/debug/tracing/events/tipc/enable
To clear the trace buffer:
echo > trace
d) Like the other trace_events, the feature like 'filter' or 'trigger'
is also usable for the tipc trace_events.
For more details, have a look at:
Documentation/trace/ftrace.txt
MAINTAINERS | add two new files 'trace.h' & 'trace.c' in tipc
Acked-by: Ying Xue <ying.xue@windriver.com>
Tested-by: Ying Xue <ying.xue@windriver.com>
Acked-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: Tuong Lien <tuong.t.lien@dektech.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
NAME_DISTRIBUTOR messages are transmitted through unicast link on TIPC
2.0, by contrast, the messages are delivered through broadcast link on
TIPC 1.7. But at present, NAME_DISTRIBUTOR messages received by
broadcast link cannot be handled in tipc_rcv() until an unicast message
arrives, which may lead to a significant delay to update name table.
To avoid this delay, we will also deal with broadcast NAME_DISTRIBUTOR
message on broadcast receive path.
Signed-off-by: Zhenbo Gao <zhenbo.gao@windriver.com>
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Similar to commit 143ece654f ("tipc: check tsk->group in tipc_wait_for_cond()")
we have to reload grp->dests too after we re-take the sock lock.
This means we need to move the dsts check after tipc_wait_for_cond()
too.
Fixes: 75da2163db ("tipc: introduce communication groups")
Reported-and-tested-by: syzbot+99f20222fc5018d2b97a@syzkaller.appspotmail.com
Cc: Ying Xue <ying.xue@windriver.com>
Cc: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Acked-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
tipc_wait_for_cond() drops socket lock before going to sleep,
but tsk->group could be freed right after that release_sock().
So we have to re-check and reload tsk->group after it wakes up.
After this patch, tipc_wait_for_cond() returns -ERESTARTSYS when
tsk->group is NULL, instead of continuing with the assumption of
a non-NULL tsk->group.
(It looks like 'dsts' should be re-checked and reloaded too, but
it is a different bug.)
Similar for tipc_send_group_unicast() and tipc_send_group_anycast().
Reported-by: syzbot+10a9db47c3a0e13eb31c@syzkaller.appspotmail.com
Fixes: b7d4263551 ("tipc: introduce flow control for group broadcast messages")
Fixes: ee106d7f94 ("tipc: introduce group anycast messaging")
Fixes: 27bd9ec027 ("tipc: introduce group unicast messaging")
Cc: Ying Xue <ying.xue@windriver.com>
Cc: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When TIPC_NLA_UDP_REMOTE is an IPv6 mcast address but
TIPC_NLA_UDP_LOCAL is an IPv4 address, a NULL-ptr deref is triggered
as the UDP tunnel sock is initialized to IPv4 or IPv6 sock merely
based on the protocol in local address.
We should just error out when the remote address and local address
have different protocols.
Reported-by: syzbot+eb4da3a20fad2e52555d@syzkaller.appspotmail.com
Cc: Ying Xue <ying.xue@windriver.com>
Cc: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Acked-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
tipc_udp_xmit() drops the packet on error, there is no
need to drop it again.
Fixes: ef20cd4dd1 ("tipc: introduce UDP replicast")
Reported-and-tested-by: syzbot+eae585ba2cc2752d3704@syzkaller.appspotmail.com
Cc: Ying Xue <ying.xue@windriver.com>
Cc: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
lock_sock() must be used in process context to be race-free with
other lock_sock() callers, for example, tipc_release(). Otherwise
using the spinlock directly can't serialize a parallel tipc_release().
As it is blocking, we have to hold the sock refcnt before
rhashtable_walk_stop() and release it after rhashtable_walk_start().
Fixes: 07f6c4bc04 ("tipc: convert tipc reference table to use generic rhashtable")
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Cc: Ying Xue <ying.xue@windriver.com>
Cc: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When setting LINK tolerance, node timer interval will be calculated
base on the LINK with lowest tolerance.
But when calculated, the old node timer interval only updated if current
setting value (tolerance/4) less than old ones regardless of number of
links as well as links' lowest tolerance value.
This caused to two cases missing if tolerance changed as following:
Case 1:
1.1/ There is one link (L1) available in the system
1.2/ Set L1's tolerance from 1500ms => lower (i.e 500ms)
1.3/ Then, fallback to default (1500ms) or higher (i.e 2000ms)
Expected:
node timer interval is 1500/4=375ms after 1.3
Result:
node timer interval will not being updated after changing tolerance at 1.3
since its value 1500/4=375ms is not less than 500/4=125ms at 1.2.
Case 2:
2.1/ There are two links (L1, L2) available in the system
2.2/ L1 and L2 tolerance value are 2000ms as initial
2.3/ Set L2's tolerance from 2000ms => lower 1500ms
2.4/ Disable link L2 (bring down its bearer)
Expected:
node timer interval is 2000ms/4=500ms after 2.4
Result:
node timer interval will not being updated after disabling L2 since
its value 2000ms/4=500ms is still not less than 1500/4=375ms at 2.3
although L2 is already not available in the system.
To fix this, we start the node interval calculation by initializing it to
a value larger than any conceivable calculated value. This way, the link
with the lowest tolerance will always determine the calculated value.
Acked-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: Hoang Le <hoang.h.le@dektech.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Trivial conflict in net/core/filter.c, a locally computed
'sdif' is now an argument to the function.
Signed-off-by: David S. Miller <davem@davemloft.net>
We see the following lockdep warning:
[ 2284.078521] ======================================================
[ 2284.078604] WARNING: possible circular locking dependency detected
[ 2284.078604] 4.19.0+ #42 Tainted: G E
[ 2284.078604] ------------------------------------------------------
[ 2284.078604] rmmod/254 is trying to acquire lock:
[ 2284.078604] 00000000acd94e28 ((&n->timer)#2){+.-.}, at: del_timer_sync+0x5/0xa0
[ 2284.078604]
[ 2284.078604] but task is already holding lock:
[ 2284.078604] 00000000f997afc0 (&(&tn->node_list_lock)->rlock){+.-.}, at: tipc_node_stop+0xac/0x190 [tipc]
[ 2284.078604]
[ 2284.078604] which lock already depends on the new lock.
[ 2284.078604]
[ 2284.078604]
[ 2284.078604] the existing dependency chain (in reverse order) is:
[ 2284.078604]
[ 2284.078604] -> #1 (&(&tn->node_list_lock)->rlock){+.-.}:
[ 2284.078604] tipc_node_timeout+0x20a/0x330 [tipc]
[ 2284.078604] call_timer_fn+0xa1/0x280
[ 2284.078604] run_timer_softirq+0x1f2/0x4d0
[ 2284.078604] __do_softirq+0xfc/0x413
[ 2284.078604] irq_exit+0xb5/0xc0
[ 2284.078604] smp_apic_timer_interrupt+0xac/0x210
[ 2284.078604] apic_timer_interrupt+0xf/0x20
[ 2284.078604] default_idle+0x1c/0x140
[ 2284.078604] do_idle+0x1bc/0x280
[ 2284.078604] cpu_startup_entry+0x19/0x20
[ 2284.078604] start_secondary+0x187/0x1c0
[ 2284.078604] secondary_startup_64+0xa4/0xb0
[ 2284.078604]
[ 2284.078604] -> #0 ((&n->timer)#2){+.-.}:
[ 2284.078604] del_timer_sync+0x34/0xa0
[ 2284.078604] tipc_node_delete+0x1a/0x40 [tipc]
[ 2284.078604] tipc_node_stop+0xcb/0x190 [tipc]
[ 2284.078604] tipc_net_stop+0x154/0x170 [tipc]
[ 2284.078604] tipc_exit_net+0x16/0x30 [tipc]
[ 2284.078604] ops_exit_list.isra.8+0x36/0x70
[ 2284.078604] unregister_pernet_operations+0x87/0xd0
[ 2284.078604] unregister_pernet_subsys+0x1d/0x30
[ 2284.078604] tipc_exit+0x11/0x6f2 [tipc]
[ 2284.078604] __x64_sys_delete_module+0x1df/0x240
[ 2284.078604] do_syscall_64+0x66/0x460
[ 2284.078604] entry_SYSCALL_64_after_hwframe+0x49/0xbe
[ 2284.078604]
[ 2284.078604] other info that might help us debug this:
[ 2284.078604]
[ 2284.078604] Possible unsafe locking scenario:
[ 2284.078604]
[ 2284.078604] CPU0 CPU1
[ 2284.078604] ---- ----
[ 2284.078604] lock(&(&tn->node_list_lock)->rlock);
[ 2284.078604] lock((&n->timer)#2);
[ 2284.078604] lock(&(&tn->node_list_lock)->rlock);
[ 2284.078604] lock((&n->timer)#2);
[ 2284.078604]
[ 2284.078604] *** DEADLOCK ***
[ 2284.078604]
[ 2284.078604] 3 locks held by rmmod/254:
[ 2284.078604] #0: 000000003368be9b (pernet_ops_rwsem){+.+.}, at: unregister_pernet_subsys+0x15/0x30
[ 2284.078604] #1: 0000000046ed9c86 (rtnl_mutex){+.+.}, at: tipc_net_stop+0x144/0x170 [tipc]
[ 2284.078604] #2: 00000000f997afc0 (&(&tn->node_list_lock)->rlock){+.-.}, at: tipc_node_stop+0xac/0x19
[...}
The reason is that the node timer handler sometimes needs to delete a
node which has been disconnected for too long. To do this, it grabs
the lock 'node_list_lock', which may at the same time be held by the
generic node cleanup function, tipc_node_stop(), during module removal.
Since the latter is calling del_timer_sync() inside the same lock, we
have a potential deadlock.
We fix this letting the timer cleanup function use spin_trylock()
instead of just spin_lock(), and when it fails to grab the lock it
just returns so that the timer handler can terminate its execution.
This is safe to do, since tipc_node_stop() anyway is about to
delete both the timer and the node instance.
Fixes: 6a939f365b ("tipc: Auto removal of peer down node instance")
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The code for reading ancillary data from a received buffer is assuming
the buffer is linear. To make this assumption true we have to linearize
the buffer before message data is read.
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a link failure is detected locally, the link is reset, the flag
link->in_session is set to false, and a RESET_MSG with the 'stopping'
bit set is sent to the peer.
The purpose of this bit is to inform the peer that this endpoint just
is going down, and that the peer should handle the reception of this
particular RESET message as a local failure. This forces the peer to
accept another RESET or ACTIVATE message from this endpoint before it
can re-establish the link. This again is necessary to ensure that
link session numbers are properly exchanged before the link comes up
again.
If a failure is detected locally at the same time at the peer endpoint
this will do the same, which is also a correct behavior.
However, when receiving such messages, the endpoints will not
distinguish between 'stopping' RESETs and ordinary ones when it comes
to updating session numbers. Both endpoints will copy the received
session number and set their 'in_session' flags to true at the
reception, while they are still expecting another RESET from the
peer before they can go ahead and re-establish. This is contradictory,
since, after applying the validation check referred to below, the
'in_session' flag will cause rejection of all such messages, and the
link will never come up again.
We now fix this by not only handling received RESET/STOPPING messages
as a local failure, but also by omitting to set a new session number
and the 'in_session' flag in such cases.
Fixes: 7ea817f4e8 ("tipc: check session number before accepting link protocol messages")
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, the broadcast retransmission algorithm is using the
'prev_retr' field in struct tipc_link to time stamp the latest broadcast
retransmission occasion. This helps to restrict retransmission of
individual broadcast packets to max once per 10 milliseconds, even
though all other criteria for retransmission are met.
We now move this time stamp to the control block of each individual
packet, and remove other limiting criteria. This simplifies the
retransmission algorithm, and eliminates any risk of logical errors
in selecting which packets can be retransmitted.
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: LUU Duc Canh <canh.d.luu@dektech.com.au>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull AFS updates from Al Viro:
"AFS series, with some iov_iter bits included"
* 'work.afs' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (26 commits)
missing bits of "iov_iter: Separate type from direction and use accessor functions"
afs: Probe multiple fileservers simultaneously
afs: Fix callback handling
afs: Eliminate the address pointer from the address list cursor
afs: Allow dumping of server cursor on operation failure
afs: Implement YFS support in the fs client
afs: Expand data structure fields to support YFS
afs: Get the target vnode in afs_rmdir() and get a callback on it
afs: Calc callback expiry in op reply delivery
afs: Fix FS.FetchStatus delivery from updating wrong vnode
afs: Implement the YFS cache manager service
afs: Remove callback details from afs_callback_break struct
afs: Commit the status on a new file/dir/symlink
afs: Increase to 64-bit volume ID and 96-bit vnode ID for YFS
afs: Don't invoke the server to read data beyond EOF
afs: Add a couple of tracepoints to log I/O errors
afs: Handle EIO from delivery function
afs: Fix TTL on VL server and address lists
afs: Implement VL server rotation
afs: Improve FS server rotation error handling
...
In the iov_iter struct, separate the iterator type from the iterator
direction and use accessor functions to access them in most places.
Convert a bunch of places to use switch-statements to access them rather
then chains of bitwise-AND statements. This makes it easier to add further
iterator types. Also, this can be more efficient as to implement a switch
of small contiguous integers, the compiler can use ~50% fewer compare
instructions than it has to use bitwise-and instructions.
Further, cease passing the iterator type into the iterator setup function.
The iterator function can set that itself. Only the direction is required.
Signed-off-by: David Howells <dhowells@redhat.com>
This reverts commit dd979b4df8.
This broke tcp_poll for SMC fallback: An AF_SMC socket establishes an
internal TCP socket for the initial handshake with the remote peer.
Whenever the SMC connection can not be established this TCP socket is
used as a fallback. All socket operations on the SMC socket are then
forwarded to the TCP socket. In case of poll, the file->private_data
pointer references the SMC socket because the TCP socket has no file
assigned. This causes tcp_poll to wait on the wrong socket.
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We have seen the following race scenario:
1) named_distribute() builds a "bulk" message, containing a PUBLISH
item for a certain publication. This is based on the contents of
the binding tables's 'cluster_scope' list.
2) tipc_named_withdraw() removes the same publication from the list,
bulds a WITHDRAW message and distributes it to all cluster nodes.
3) tipc_named_node_up(), which was calling named_distribute(), sends
out the bulk message built under 1)
4) The WITHDRAW message arrives at the just detected node, finds
no corresponding publication, and is dropped.
5) The PUBLISH item arrives at the same node, is added to its binding
table, and remains there forever.
This arrival disordering was earlier taken care of by the backlog queue,
originally added for a different purpose, which was removed in the
commit referred to below, but we now need a different solution.
In this commit, we replace the rcu lock protecting the 'cluster_scope'
list with a regular RW lock which comprises even the sending of the
bulk message. This both guarantees both the list integrity and the
message sending order. We will later add a commit which cleans up
this code further.
Note that this commit needs recently added commit d3092b2efc ("tipc:
fix unsafe rcu locking when accessing publication list") to apply
cleanly.
Fixes: 37922ea4a3 ("tipc: permit overlapping service ranges in name table")
Reported-by: Tuong Lien Tong <tuong.t.lien@dektech.com.au>
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Got below warning with gcc 8.2 compiler.
net/tipc/topsrv.c: In function ‘tipc_topsrv_start’:
net/tipc/topsrv.c:660:2: warning: ‘strncpy’ specified bound depends on the length of the source argument [-Wstringop-overflow=]
strncpy(srv->name, name, strlen(name) + 1);
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
net/tipc/topsrv.c:660:27: note: length computed here
strncpy(srv->name, name, strlen(name) + 1);
^~~~~~~~~~~~
So change it to correct length and use strscpy.
Signed-off-by: Guoqing Jiang <gqjiang@suse.com>
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
net/sched/cls_api.c has overlapping changes to a call to
nlmsg_parse(), one (from 'net') added rtm_tca_policy instead of NULL
to the 5th argument, and another (from 'net-next') added cb->extack
instead of NULL to the 6th argument.
net/ipv4/ipmr_base.c is a case of a bug fix in 'net' being done to
code which moved (to mr_table_dump)) in 'net-next'. Thanks to David
Ahern for the heads up.
Signed-off-by: David S. Miller <davem@davemloft.net>
We initialize a struct tipc_event allocated on the kernel stack to
zero to avert info leak to user space.
Reported-by: syzbot+057458894bc8cada4dee@syzkaller.appspotmail.com
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The binding table's 'cluster_scope' list is rcu protected to handle
races between threads changing the list and those traversing the list at
the same moment. We have now found that the function named_distribute()
uses the regular list_for_each() macro to traverse the said list.
Likewise, the function tipc_named_withdraw() is removing items from the
same list using the regular list_del() call. When these two functions
execute in parallel we see occasional crashes.
This commit fixes this by adding the missing _rcu() suffixes.
Signed-off-by: Tung Nguyen <tung.q.nguyen@dektech.com.au>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the commit referred to below we added link tolerance as an additional
criteria for declaring broadcast transmission "stale" and resetting the
unicast links to the affected node.
Unfortunately, this 'improvement' introduced two bugs, which each and
one alone cause only limited problems, but combined lead to seemingly
stochastic unicast link resets, depending on the amount of broadcast
traffic transmitted.
The first issue, a missing initialization of the 'tolerance' field of
the receiver broadcast link, was recently fixed by commit 047491ea33
("tipc: set link tolerance correctly in broadcast link").
Ths second issue, where we omit to reset the 'stale_cnt' field of
the same link after a 'stale' period is over, leads to this counter
accumulating over time, and in the absence of the 'tolerance' criteria
leads to the above described symptoms. This commit adds the missing
initialization.
Fixes: a4dc70d46c ("tipc: extend link reset criteria for stale packet retransmission")
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
INADDR_ANY is hard-coded when activating UDP bearer. So, we could not
bind to a specific IP address even with replicast mode using - given
remote ip address instead of using multicast ip address.
In this commit, we fixed it by checking and switch to use appropriate
local ip address.
before:
$netstat -plu
Active Internet connections (only servers)
Proto Recv-Q Send-Q Local Address Foreign Address
udp 0 0 **0.0.0.0:6118** 0.0.0.0:*
after:
$netstat -plu
Active Internet connections (only servers)
Proto Recv-Q Send-Q Local Address Foreign Address
udp 0 0 **10.0.0.2:6118** 0.0.0.0:*
Acked-by: Ying Xue <ying.xue@windriver.com>
Acked-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: Hoang Le <hoang.h.le@dektech.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts were easy to resolve using immediate context mostly,
except the cls_u32.c one where I simply too the entire HEAD
chunk.
Signed-off-by: David S. Miller <davem@davemloft.net>
When booting kernel with LOCKDEP option, below warning info was found:
WARNING: possible recursive locking detected
4.19.0-rc7+ #14 Not tainted
--------------------------------------------
swapper/0/1 is trying to acquire lock:
00000000dcfc0fc8 (&(&list->lock)->rlock#4){+...}, at: spin_lock_bh
include/linux/spinlock.h:334 [inline]
00000000dcfc0fc8 (&(&list->lock)->rlock#4){+...}, at:
tipc_link_reset+0x125/0xdf0 net/tipc/link.c:850
but task is already holding lock:
00000000cbb9b036 (&(&list->lock)->rlock#4){+...}, at: spin_lock_bh
include/linux/spinlock.h:334 [inline]
00000000cbb9b036 (&(&list->lock)->rlock#4){+...}, at:
tipc_link_reset+0xfa/0xdf0 net/tipc/link.c:849
other info that might help us debug this:
Possible unsafe locking scenario:
CPU0
----
lock(&(&list->lock)->rlock#4);
lock(&(&list->lock)->rlock#4);
*** DEADLOCK ***
May be due to missing lock nesting notation
2 locks held by swapper/0/1:
#0: 00000000f7539d34 (pernet_ops_rwsem){+.+.}, at:
register_pernet_subsys+0x19/0x40 net/core/net_namespace.c:1051
#1: 00000000cbb9b036 (&(&list->lock)->rlock#4){+...}, at:
spin_lock_bh include/linux/spinlock.h:334 [inline]
#1: 00000000cbb9b036 (&(&list->lock)->rlock#4){+...}, at:
tipc_link_reset+0xfa/0xdf0 net/tipc/link.c:849
stack backtrace:
CPU: 0 PID: 1 Comm: swapper/0 Not tainted 4.19.0-rc7+ #14
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.10.2-1 04/01/2014
Call Trace:
__dump_stack lib/dump_stack.c:77 [inline]
dump_stack+0x1af/0x295 lib/dump_stack.c:113
print_deadlock_bug kernel/locking/lockdep.c:1759 [inline]
check_deadlock kernel/locking/lockdep.c:1803 [inline]
validate_chain kernel/locking/lockdep.c:2399 [inline]
__lock_acquire+0xf1e/0x3c60 kernel/locking/lockdep.c:3411
lock_acquire+0x1db/0x520 kernel/locking/lockdep.c:3900
__raw_spin_lock_bh include/linux/spinlock_api_smp.h:135 [inline]
_raw_spin_lock_bh+0x31/0x40 kernel/locking/spinlock.c:168
spin_lock_bh include/linux/spinlock.h:334 [inline]
tipc_link_reset+0x125/0xdf0 net/tipc/link.c:850
tipc_link_bc_create+0xb5/0x1f0 net/tipc/link.c:526
tipc_bcast_init+0x59b/0xab0 net/tipc/bcast.c:521
tipc_init_net+0x472/0x610 net/tipc/core.c:82
ops_init+0xf7/0x520 net/core/net_namespace.c:129
__register_pernet_operations net/core/net_namespace.c:940 [inline]
register_pernet_operations+0x453/0xac0 net/core/net_namespace.c:1011
register_pernet_subsys+0x28/0x40 net/core/net_namespace.c:1052
tipc_init+0x83/0x104 net/tipc/core.c:140
do_one_initcall+0x109/0x70a init/main.c:885
do_initcall_level init/main.c:953 [inline]
do_initcalls init/main.c:961 [inline]
do_basic_setup init/main.c:979 [inline]
kernel_init_freeable+0x4bd/0x57f init/main.c:1144
kernel_init+0x13/0x180 init/main.c:1063
ret_from_fork+0x3a/0x50 arch/x86/entry/entry_64.S:413
The reason why the noise above was complained by LOCKDEP is because we
nested to hold l->wakeupq.lock and l->inputq->lock in tipc_link_reset
function. In fact it's unnecessary to move skb buffer from l->wakeupq
queue to l->inputq queue while holding the two locks at the same time.
Instead, we can move skb buffers in l->wakeupq queue to a temporary
list first and then move the buffers of the temporary list to l->inputq
queue, which is also safe for us.
Fixes: 3f32d0be6c ("tipc: lock wakeup & inputq at tipc_link_reset()")
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Acked-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In tipc_sk_filter_rcv(), when we detect protocol messages with error we
call tipc_sk_conn_proto_rcv() and let it reset the connection and notify
the socket by calling sk->sk_state_change().
However, tipc_sk_filter_rcv() may have been called from the function
tipc_backlog_rcv(), in which case the socket lock is held and the socket
already awake. This means that the sk_state_change() call is ignored and
the error notification lost. Now the receive queue will remain empty and
the socket sleeps forever.
In this commit, we convert the protocol message into a connection abort
message and enqueue it into the socket's receive queue. By this addition
to the above state change we cover all conditions.
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Parthasarathy Bhuvaragan <parthasarathy.bhuvaragan@ericsson.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the patch referred to below we added link tolerance as an additional
criteria for declaring broadcast transmission "stale" and resetting the
affected links.
However, the 'tolerance' field of the broadcast link is never set, and
remains at zero. This renders the whole commit without the intended
improving effect, but luckily also with no negative effect.
In this commit we add the missing initialization.
Fixes: a4dc70d46c ("tipc: extend link reset criteria for stale packet retransmission")
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Minor conflict in net/core/rtnetlink.c, David Ahern's bug fix in 'net'
overlapped the renaming of a netlink attribute in net-next.
Signed-off-by: David S. Miller <davem@davemloft.net>
The initial session number when a link is created is based on a random
value, taken from struct tipc_net->random. It is then incremented for
each link reset to avoid mixing protocol messages from different link
sessions.
However, when a bearer is reset all its links are deleted, and will
later be re-created using the same random value as the first time.
This means that if the link never went down between creation and
deletion we will still sometimes have two subsequent sessions with
the same session number. In virtual environments with potentially
long transmission times this has turned out to be a real problem.
We now fix this by randomizing the session number each time a link
is created.
With a session number size of 16 bits this gives a risk of session
collision of 1/64k. To reduce this further, we also introduce a sanity
check on the very first STATE message arriving at a link. If this has
an acknowledge value differing from 0, which is logically impossible,
we ignore the message. The final risk for session collision is hence
reduced to 1/4G, which should be sufficient.
Signed-off-by: LUU Duc Canh <canh.d.luu@dektech.com.au>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We see the following scenario:
1) Link endpoint B on node 1 discovers that its peer endpoint is gone.
Since there is a second working link, failover procedure is started.
2) Link endpoint A on node 1 sends a FAILOVER message to peer endpoint
A on node 2. The node item 1->2 goes to state FAILINGOVER.
3) Linke endpoint A/2 receives the failover, and is supposed to take
down its parallell link endpoint B/2, while producing a FAILOVER
message to send back to A/1.
4) However, B/2 has already been deleted, so no FAILOVER message can
created.
5) Node 1->2 remains in state FAILINGOVER forever, refusing to receive
any messages that can bring B/1 up again. We are left with a non-
redundant link between node 1 and 2.
We fix this with letting endpoint A/2 build a dummy FAILOVER message
to send to back to A/1, so that the situation can be resolved.
Signed-off-by: LUU Duc Canh <canh.d.luu@dektech.com.au>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Default socket receive buffer size for a listener socket is 2Mb. For
each arriving empty SYN, the linux kernel allocates a 768 bytes buffer.
This means that a listener socket can serve maximum 2700 simultaneous
empty connection setup requests before it hits a receive buffer
overflow, and much fewer if the SYN is carrying any significant
amount of data.
When this happens the setup request is rejected, and the client
receives an ECONNREFUSED error.
This commit mitigates this problem by letting the client socket try to
retransmit the SYN message multiple times when it sees it rejected with
the code TIPC_ERR_OVERLOAD. Retransmission is done at random intervals
in the range of [100 ms, setup_timeout / 4], as many times as there is
room for within the setup timeout limit.
Signed-off-by: Tung Nguyen <tung.q.nguyen@dektech.com.au>
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Messages intended for intitating a connection are currently
indistinguishable from regular datagram messages. The TIPC
protocol specification defines bit 17 in word 0 as a SYN bit
to allow sanity check of such messages in the listening socket,
but this has so far never been implemented.
We do that in this commit.
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We refactor the function tipc_sk_filter_connect(), both to make it
more readable and as a preparation for the next commit.
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We refactor this function as a preparation for the coming commits in
the same series.
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The function tipc_msg_reverse() is reversing the header of a message
while reusing the original buffer. We have seen at several occasions
that this may have unfortunate side effects when the buffer to be
reversed is a clone.
In one of the following commits we will again need to reverse cloned
buffers, so this is the right time to permanently eliminate this
problem. In this commit we let the said function always consume the
original buffer and replace it with a new one when applicable.
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In tipc_link_reset() we copy the wakeup queue to input queue using
skb_queue_splice_init(link->wakeupq, link->inputq).
This is performed without holding any locks. The lists might be
simultaneously be accessed by other cpu threads in tipc_sk_rcv(),
something leading to to random missing packets.
Signed-off-by: Parthasarathy Bhuvaragan <parthasarathy.bhuvaragan@ericsson.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If we detect that under lying carrier detects errors and goes down,
we reset the bearer.
Signed-off-by: Parthasarathy Bhuvaragan <parthasarathy.bhuvaragan@ericsson.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the case of implicit connect message with data > 1K, the flow
control accounting is incorrect. At this state, the socket does not
know the peer nodes capability and falls back to legacy flow control
by return 1, however the receiver of this message will perform the
new block accounting. This leads to a slack and eventually traffic
disturbance.
In this commit, we perform tipc_node_get_capabilities() at implicit
connect and perform accounting based on the peer's capability.
Signed-off-by: Parthasarathy Bhuvaragan <parthasarathy.bhuvaragan@ericsson.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When __tipc_dump_start() fails with running out of memory,
we have no reason to continue, especially we should avoid
calling tipc_dump_done().
Fixes: 8f5c5fcf35 ("tipc: call start and done ops directly in __tipc_nl_compat_dumpit()")
Reported-and-tested-by: syzbot+3f8324abccfbf8c74a9f@syzkaller.appspotmail.com
Cc: Jon Maloy <jon.maloy@ericsson.com>
Cc: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
An SKB is not on a list if skb->next is NULL.
Codify this convention into a helper function and use it
where we are dequeueing an SKB and need to mark it as such.
Signed-off-by: David S. Miller <davem@davemloft.net>
__tipc_nl_compat_dumpit() uses a netlink_callback on stack,
so the only way to align it with other ->dumpit() call path
is calling tipc_dump_start() and tipc_dump_done() directly
inside it. Otherwise ->dumpit() would always get NULL from
cb->args[].
But tipc_dump_start() uses sock_net(cb->skb->sk) to retrieve
net pointer, the cb->skb here doesn't set skb->sk, the net pointer
is saved in msg->net instead, so introduce a helper function
__tipc_dump_start() to pass in msg->net.
Ying pointed out cb->args[0...3] are already used by other
callbacks on this call path, so we can't use cb->args[0] any
more, use cb->args[4] instead.
Fixes: 9a07efa9ae ("tipc: switch to rhashtable iterator")
Reported-and-tested-by: syzbot+e93a2c41f91b8e2c7d9b@syzkaller.appspotmail.com
Cc: Jon Maloy <jon.maloy@ericsson.com>
Cc: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Before we unlock the sock in tipc_release(), we have to
detach sk->sk_socket from sk, otherwise a parallel
tipc_sk_fill_sock_diag() could stil read it after we
free this socket.
Fixes: c30b70deb5 ("tipc: implement socket diagnostics for AF_TIPC")
Reported-and-tested-by: syzbot+48804b87c16588ad491d@syzkaller.appspotmail.com
Cc: Jon Maloy <jon.maloy@ericsson.com>
Cc: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Trivial fix for two spelling mistakes.
Signed-off-by: Zhenbo Gao <zhenbo.gao@windriver.com>
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove the following obsolete parameter comments of tipc_topsrv struct:
@rcvbuf_cache
@tipc_conn_new
@tipc_conn_release
@tipc_conn_recvmsg
@imp
@type
Add the comments for the missing parameters below of tipc_topsrv struct:
@awork
@listener
Remove the unused or duplicated parameter comments of tipc_conn struct:
@outqueue_lock
@rx_action
Signed-off-by: Zhenbo Gao <zhenbo.gao@windriver.com>
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
syzbot reported a use-after-free in tipc_group_fill_sock_diag(),
where tipc_group_fill_sock_diag() still reads tsk->group meanwhile
tipc_group_delete() just deletes it in tipc_release().
tipc_nl_sk_walk() aims to lock this sock when walking each sock
in the hash table to close race conditions with sock changes like
this one, by acquiring tsk->sk.sk_lock.slock spinlock, unfortunately
this doesn't work at all. All non-BH call path should take
lock_sock() instead to make it work.
tipc_nl_sk_walk() brutally iterates with raw rht_for_each_entry_rcu()
where RCU read lock is required, this is the reason why lock_sock()
can't be taken on this path. This could be resolved by switching to
rhashtable iterator API's, where taking a sleepable lock is possible.
Also, the iterator API's are friendly for restartable calls like
diag dump, the last position is remembered behind the scence,
all we need to do here is saving the iterator into cb->args[].
I tested this with parallel tipc diag dump and thousands of tipc
socket creation and release, no crash or memory leak.
Reported-by: syzbot+b9c8f3ab2994b7cd1625@syzkaller.appspotmail.com
Cc: Jon Maloy <jon.maloy@ericsson.com>
Cc: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
rhashtable_walk_exit() must be paired with rhashtable_walk_enter().
Fixes: 40f9f43970 ("tipc: Fix tipc_sk_reinit race conditions")
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In function tipc_dest_push, the 32bit variables 'node' and 'port'
are stored separately in uppper and lower part of 64bit 'value'.
Then this value is assigned to dst->value which is a union like:
union
{
struct {
u32 port;
u32 node;
};
u64 value;
}
This works on little-endian machines like x86 but fails on big-endian
machines.
The fix remove the 'value' stack parameter and even the 'value'
member of the union in tipc_dest, assign the 'node' and 'port' member
directly with the input parameter to avoid the endian issue.
Fixes: a80ae5306a ("tipc: improve destination linked list")
Signed-off-by: Zhenbo Gao <zhenbo.gao@windriver.com>
Acked-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: Haiqing Bai <Haiqing.Bai@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 9faa89d4ed ("tipc: make function tipc_net_finalize() thread
safe") tries to make it thread safe to set node address, so it uses
node_list_lock lock to serialize the whole process of setting node
address in tipc_net_finalize(). But it causes the following interrupt
unsafe locking scenario:
CPU0 CPU1
---- ----
rht_deferred_worker()
rhashtable_rehash_table()
lock(&(&ht->lock)->rlock)
tipc_nl_compat_doit()
tipc_net_finalize()
local_irq_disable();
lock(&(&tn->node_list_lock)->rlock);
tipc_sk_reinit()
rhashtable_walk_enter()
lock(&(&ht->lock)->rlock);
<Interrupt>
tipc_disc_rcv()
tipc_node_check_dest()
tipc_node_create()
lock(&(&tn->node_list_lock)->rlock);
*** DEADLOCK ***
When rhashtable_rehash_table() holds ht->lock on CPU0, it doesn't
disable BH. So if an interrupt happens after the lock, it can create
an inverse lock ordering between ht->lock and tn->node_list_lock. As
a consequence, deadlock might happen.
The reason causing the inverse lock ordering scenario above is because
the initial purpose of node_list_lock is not designed to do the
serialization of node address setting.
As cmpxchg() can guarantee CAS (compare-and-swap) process is atomic,
we use it to replace node_list_lock to ensure setting node address can
be atomically finished. It turns out the potential deadlock can be
avoided as well.
Fixes: 9faa89d4ed ("tipc: make function tipc_net_finalize() thread safe")
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Acked-by: Jon Maloy <maloy@donjonn.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Variables 'tn' and 'oport' are being assigned but are never used hence
they are redundant and can be removed.
Cleans up clang warnings:
warning: variable 'oport' set but not used [-Wunused-but-set-variable]
warning: variable 'tn' set but not used [-Wunused-but-set-variable]
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The wait_address argument is always directly derived from the filp
argument, so remove it.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
tipc_bcast_init() is never called in atomic context.
It calls kzalloc() with GFP_ATOMIC, which is not necessary.
GFP_ATOMIC can be replaced with GFP_KERNEL.
This is found by a static analysis tool named DCNS written by myself.
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
tipc_nametbl_init() is never called in atomic context.
It calls kzalloc() with GFP_ATOMIC, which is not necessary.
GFP_ATOMIC can be replaced with GFP_KERNEL.
This is found by a static analysis tool named DCNS written by myself.
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
when tipc_own_id failed to obtain node identity,dev_put should
be call before return -EINVAL.
Fixes: 682cd3cf94 ("tipc: confgiure and apply UDP bearer MTU on running links")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes the following sparse warnings:
net/tipc/link.c:376:5: warning: symbol 'link_bc_rcv_gap' was not declared. Should it be static?
net/tipc/link.c:823:6: warning: symbol 'link_prepare_wakeup' was not declared. Should it be static?
net/tipc/link.c:959:6: warning: symbol 'tipc_link_advance_backlog' was not declared. Should it be static?
net/tipc/link.c:1009:5: warning: symbol 'tipc_link_retrans' was not declared. Should it be static?
net/tipc/monitor.c:687:5: warning: symbol '__tipc_nl_add_monitor_peer' was not declared. Should it be static?
net/tipc/group.c:230:20: warning: symbol 'tipc_group_find_member' was not declared. Should it be static?
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The commit referred to below introduced an update of the link
capabilities field that is not safe. Given the recently added
feature to remove idle node and link items after 5 minutes, there
is a small risk that the update will happen at the very moment the
targeted link is being removed. To avoid this we have to perform
the update inside the node item's write lock protection.
Fixes: 9012de5089 ("tipc: add sequence number check for link STATE messages")
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After commit eb929a91b2 ("tipc: improve poll() for group member socket"),
it is no longer used.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Acked-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
tipc_link_is_active is no longer used and can be removed.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Acked-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In some virtual environments we observe a significant higher number of
packet reordering and delays than we have been used to traditionally.
This makes it necessary with stricter checks on incoming link protocol
messages' session number, which until now only has been validated for
RESET messages.
Since the other two message types, ACTIVATE and STATE messages also
carry this number, it is easy to extend the validation check to those
messages.
We also introduce a flag indicating if a link has a valid peer session
number or not. This eliminates the mixing of 32- and 16-bit arithmethics
we are currently using to achieve this.
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some switch infrastructures produce huge amounts of packet duplicates.
This becomes a problem if those messages are STATE/NACK protocol
messages, causing unnecessary retransmissions of already accepted
packets.
We now introduce a unique sequence number per STATE protocol message
so that duplicates can be identified and ignored. This will also be
useful when tracing such cases, and to avert replay attacks when TIPC
is encrypted.
For compatibility reasons we have to introduce a new capability flag
TIPC_LINK_PROTO_SEQNO to handle this new feature.
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently a link is declared stale and reset if there has been 100
repeated attempts to retransmit the same packet. However, in certain
infrastructures we see that packet (NACK) duplicates and delays may
cause such retransmit attempts to occur at a high rate, so that the
peer doesn't have a reasonable chance to acknowledge the reception
before the 100-limit is hit. This may take much less than the
stipulated link tolerance time, and despite that probe/probe replies
otherwise go through as normal.
We now extend the criteria for link reset to also being time based.
I.e., we don't reset the link until the link tolerance time is passed
AND we have made 100 retransmissions attempts.
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The setting of the node address is not thread safe, meaning that
two discoverers may decide to set it simultanously, with a duplicate
entry in the name table as result. We fix that with this commit.
Fixes: 25b0b9c4e8 ("tipc: handle collisions of 32-bit node address hash values")
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The duplicate address discovery protocol is not safe against two
discoverers running in parallel. The one executing first after the
trial period is over will set the node address and change its own
message type to DSC_REQ_MSG. The one executing last may find that the
node address is already set, and never change message type, with the
result that its links may never be established.
In this commmit we ensure that the message type always is set correctly
after the trial period is over.
Fixes: 25b0b9c4e8 ("tipc: handle collisions of 32-bit node address hash values")
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With the duplicate address discovery protocol for tipc nodes addresses
we introduced a one second trial period before a node is allocated a
hash number to use as address.
Unfortunately, we miss to handle the case when a regular LINK REQUEST/
RESPONSE arrives from a cluster node during the trial period. Such
messages are not ignored as they should be, leading to links setup
attempts while the node still has no address.
Fixes: 25b0b9c4e8 ("tipc: handle collisions of 32-bit node address hash values")
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The function for checking if there is an node address conflict is
supposed to return a suggestion for a new address if it finds a
conflict, and zero otherwise. But in case the peer being checked
is previously unknown it does instead return a "suggestion" for
the checked address itself. This results in a DSC_TRIAL_FAIL_MSG
being sent unecessarily to the peer, and sometimes makes the trial
period starting over again.
Fixes: 25b0b9c4e8 ("tipc: handle collisions of 32-bit node address hash values")
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Warning level 2 was used: -Wimplicit-fallthrough=2
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Simple overlapping changes in stmmac driver.
Adjust skb_gro_flush_final_remcsum function signature to make GRO list
changes in net-next, as per Stephen Rothwell's example merge
resolution.
Signed-off-by: David S. Miller <davem@davemloft.net>
This commit extends the existing TIPC socket diagnostics framework
for information related to TIPC group communication.
Acked-by: Ying Xue <ying.xue@windriver.com>
Acked-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: GhantaKrishnamurthy MohanKrishna <mohan.krishna.ghanta.krishnamurthy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A peer node is considered down if there are no
active links (or) lost contact to the node. In current implementation,
a peer node instance is deleted either if
a) TIPC module is removed (or)
b) Application can use a netlink/iproute2 interface to delete a
specific down node.
Thus, a down node instance lives in the system forever, unless the
application explicitly removes it.
We fix this by deleting the nodes which are down for
a specified amount of time (5 minutes).
Existing node supervision timer is used to achieve this.
Acked-by: Ying Xue <ying.xue@windriver.com>
Acked-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: GhantaKrishnamurthy MohanKrishna <mohan.krishna.ghanta.krishnamurthy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In single-link usage, the function tipc_node_timeout() still iterates
over the whole link array to handle each link. Given that the maximum
number of bearers are 3, there are 2 redundant iterations with lock
grab/release. Since this function is executing very frequently it makes
sense to optimize it.
This commit adds conditional checking to exit from the loop if the
known number of configured links has already been accessed.
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Tung Nguyen <tung.q.nguyen@dektech.com.au>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The function tipc_msg_extract() is using skb_clone() to clone inner
messages from a message bundle buffer. Although this method is safe,
it has an undesired effect that each buffer clone inherits the
true-size of the bundling buffer. As a result, the buffer clone
almost always ends up with being copied anyway by the message
validation function. This makes the cloning into a sub-optimization.
In this commit we take the consequence of this realization, and copy
each inner message to a separately allocated buffer up front in the
extraction function.
As a bonus we can now eliminate the two cases where we had to copy
re-routed packets that may potentially go out on the wire again.
Signed-off-by: Tung Nguyen <tung.q.nguyen@dektech.com.au>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The poll() changes were not well thought out, and completely
unexplained. They also caused a huge performance regression, because
"->poll()" was no longer a trivial file operation that just called down
to the underlying file operations, but instead did at least two indirect
calls.
Indirect calls are sadly slow now with the Spectre mitigation, but the
performance problem could at least be largely mitigated by changing the
"->get_poll_head()" operation to just have a per-file-descriptor pointer
to the poll head instead. That gets rid of one of the new indirections.
But that doesn't fix the new complexity that is completely unwarranted
for the regular case. The (undocumented) reason for the poll() changes
was some alleged AIO poll race fixing, but we don't make the common case
slower and more complex for some uncommon special case, so this all
really needs way more explanations and most likely a fundamental
redesign.
[ This revert is a revert of about 30 different commits, not reverted
individually because that would just be unnecessarily messy - Linus ]
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Christoph Hellwig <hch@lst.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull networking updates from David Miller:
1) Add Maglev hashing scheduler to IPVS, from Inju Song.
2) Lots of new TC subsystem tests from Roman Mashak.
3) Add TCP zero copy receive and fix delayed acks and autotuning with
SO_RCVLOWAT, from Eric Dumazet.
4) Add XDP_REDIRECT support to mlx5 driver, from Jesper Dangaard
Brouer.
5) Add ttl inherit support to vxlan, from Hangbin Liu.
6) Properly separate ipv6 routes into their logically independant
components. fib6_info for the routing table, and fib6_nh for sets of
nexthops, which thus can be shared. From David Ahern.
7) Add bpf_xdp_adjust_tail helper, which can be used to generate ICMP
messages from XDP programs. From Nikita V. Shirokov.
8) Lots of long overdue cleanups to the r8169 driver, from Heiner
Kallweit.
9) Add BTF ("BPF Type Format"), from Martin KaFai Lau.
10) Add traffic condition monitoring to iwlwifi, from Luca Coelho.
11) Plumb extack down into fib_rules, from Roopa Prabhu.
12) Add Flower classifier offload support to igb, from Vinicius Costa
Gomes.
13) Add UDP GSO support, from Willem de Bruijn.
14) Add documentation for eBPF helpers, from Quentin Monnet.
15) Add TLS tx offload to mlx5, from Ilya Lesokhin.
16) Allow applications to be given the number of bytes available to read
on a socket via a control message returned from recvmsg(), from
Soheil Hassas Yeganeh.
17) Add x86_32 eBPF JIT compiler, from Wang YanQing.
18) Add AF_XDP sockets, with zerocopy support infrastructure as well.
From Björn Töpel.
19) Remove indirect load support from all of the BPF JITs and handle
these operations in the verifier by translating them into native BPF
instead. From Daniel Borkmann.
20) Add GRO support to ipv6 gre tunnels, from Eran Ben Elisha.
21) Allow XDP programs to do lookups in the main kernel routing tables
for forwarding. From David Ahern.
22) Allow drivers to store hardware state into an ELF section of kernel
dump vmcore files, and use it in cxgb4. From Rahul Lakkireddy.
23) Various RACK and loss detection improvements in TCP, from Yuchung
Cheng.
24) Add TCP SACK compression, from Eric Dumazet.
25) Add User Mode Helper support and basic bpfilter infrastructure, from
Alexei Starovoitov.
26) Support ports and protocol values in RTM_GETROUTE, from Roopa
Prabhu.
27) Support bulking in ->ndo_xdp_xmit() API, from Jesper Dangaard
Brouer.
28) Add lots of forwarding selftests, from Petr Machata.
29) Add generic network device failover driver, from Sridhar Samudrala.
* ra.kernel.org:/pub/scm/linux/kernel/git/davem/net-next: (1959 commits)
strparser: Add __strp_unpause and use it in ktls.
rxrpc: Fix terminal retransmission connection ID to include the channel
net: hns3: Optimize PF CMDQ interrupt switching process
net: hns3: Fix for VF mailbox receiving unknown message
net: hns3: Fix for VF mailbox cannot receiving PF response
bnx2x: use the right constant
Revert "net: sched: cls: Fix offloading when ingress dev is vxlan"
net: dsa: b53: Fix for brcm tag issue in Cygnus SoC
enic: fix UDP rss bits
netdev-FAQ: clarify DaveM's position for stable backports
rtnetlink: validate attributes in do_setlink()
mlxsw: Add extack messages for port_{un, }split failures
netdevsim: Add extack error message for devlink reload
devlink: Add extack to reload and port_{un, }split operations
net: metrics: add proper netlink validation
ipmr: fix error path when ipmr_new_table fails
ip6mr: only set ip6mr_table from setsockopt when ip6mr_new_table succeeds
net: hns3: remove unused hclgevf_cfg_func_mta_filter
netfilter: provide udp*_lib_lookup for nf_tproxy
qed*: Utilize FW 8.37.2.0
...
Pull aio updates from Al Viro:
"Majority of AIO stuff this cycle. aio-fsync and aio-poll, mostly.
The only thing I'm holding back for a day or so is Adam's aio ioprio -
his last-minute fixup is trivial (missing stub in !CONFIG_BLOCK case),
but let it sit in -next for decency sake..."
* 'work.aio-1' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (46 commits)
aio: sanitize the limit checking in io_submit(2)
aio: fold do_io_submit() into callers
aio: shift copyin of iocb into io_submit_one()
aio_read_events_ring(): make a bit more readable
aio: all callers of aio_{read,write,fsync,poll} treat 0 and -EIOCBQUEUED the same way
aio: take list removal to (some) callers of aio_complete()
aio: add missing break for the IOCB_CMD_FDSYNC case
random: convert to ->poll_mask
timerfd: convert to ->poll_mask
eventfd: switch to ->poll_mask
pipe: convert to ->poll_mask
crypto: af_alg: convert to ->poll_mask
net/rxrpc: convert to ->poll_mask
net/iucv: convert to ->poll_mask
net/phonet: convert to ->poll_mask
net/nfc: convert to ->poll_mask
net/caif: convert to ->poll_mask
net/bluetooth: convert to ->poll_mask
net/sctp: convert to ->poll_mask
net/tipc: convert to ->poll_mask
...
The bpf syscall and selftests conflicts were trivial
overlapping changes.
The r8169 change involved moving the added mdelay from 'net' into a
different function.
A TLS close bug fix overlapped with the splitting of the TLS state
into separate TX and RX parts. I just expanded the tests in the bug
fix from "ctx->conf == X" into "ctx->tx_conf == X && ctx->rx_conf
== X".
Signed-off-by: David S. Miller <davem@davemloft.net>
In commit be47e41d77 ("tipc: fix use-after-free in tipc_nametbl_stop")
we fixed a problem caused by premature release of service range items.
That fix is correct, and solved the problem. However, it doesn't address
the root of the problem, which is that we don't lookup the tipc_service
-> service_range -> publication items in the correct hierarchical
order.
In this commit we try to make this right, and as a side effect obtain
some code simplification.
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After the introduction of a 128-bit node identity it may be difficult
for a user to correlate between this identity and the generated node
hash address.
We now try to make this easier by introducing a new ioctl() call for
fetching a node identity by using the hash value as key. This will
be particularly useful when we extend some of the commands in the
'tipc' tool, but we also expect regular user applications to need
this feature.
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 36a50a989e ("tipc: fix infinite loop when dumping link monitor
summary") intended to fix a problem with user tool looping when max
number of bearers are enabled.
Unfortunately, the wrong version of the commit was posted, so the
problem was not solved at all.
This commit adds the missing part.
Fixes: 36a50a989e ("tipc: fix infinite loop when dumping link monitor summary")
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, we have option to configure MTU of UDP media. The configured
MTU takes effect on the links going up after that moment. I.e, a user
has to reset bearer to have new value applied across its links. This is
confusing and disturbing on a running cluster.
We now introduce the functionality to change the default UDP bearer MTU
in struct tipc_bearer. Additionally, the links are updated dynamically,
without any need for a reset, when bearer value is changed. We leverage
the existing per-link functionality and the design being symetrical to
the confguration of link tolerance.
Acked-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: GhantaKrishnamurthy MohanKrishna <mohan.krishna.ghanta.krishnamurthy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In previous commit, we changed the default emulated MTU for UDP bearers
to 14k.
This commit adds the functionality to set/change the default value
by configuring new MTU for UDP media. UDP bearer(s) have to be disabled
and enabled back for the new MTU to take effect.
Acked-by: Ying Xue <ying.xue@windriver.com>
Acked-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: GhantaKrishnamurthy MohanKrishna <mohan.krishna.ghanta.krishnamurthy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, all bearers are configured with MTU value same as the
underlying L2 device. However, in case of bearers with media type
UDP, higher throughput is possible with a fixed and higher emulated
MTU value than adapting to the underlying L2 MTU.
In this commit, we introduce a parameter mtu in struct tipc_media
and a default value is set for UDP. A default value of 14k
was determined by experimentation and found to have a higher throughput
than 16k. MTU for UDP bearers are assigned the above set value of
media MTU.
Acked-by: Ying Xue <ying.xue@windriver.com>
Acked-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: GhantaKrishnamurthy MohanKrishna <mohan.krishna.ghanta.krishnamurthy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When configuring the number of used bearers to MAX_BEARER and issuing
command "tipc link monitor summary", the command enters infinite loop
in user space.
This issue happens because function tipc_nl_node_dump_monitor() returns
the wrong 'prev_bearer' value when all potential monitors have been
scanned.
The correct behavior is to always try to scan all monitors until either
the netlink message is full, in which case we return the bearer identity
of the affected monitor, or we continue through the whole bearer array
until we can return MAX_BEARERS. This solution also caters for the case
where there may be gaps in the bearer array.
Signed-off-by: Tung Nguyen <tung.q.nguyen@dektech.com.au>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When we delete a service item in tipc_nametbl_stop() we loop over
all service ranges in the service's RB tree, and for each service
range we loop over its pertaining publications while calling
tipc_service_remove_publ() for each of them.
However, tipc_service_remove_publ() has the side effect that it also
removes the comprising service range item when there are no publications
left. This leads to a "use-after-free" access when the inner loop
continues to the next iteration, since the range item holding the list
we are looping no longer exists.
We fix this by moving the delete of the service range item outside
the said function. Instead, we now let the two functions calling it
test if the list is empty and perform the removal when that is the
case.
Reported-by: syzbot+d64b64afc55660106556@syzkaller.appspotmail.com
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
syzbot reported a crash in __tipc_nl_net_set() caused by NULL dereference.
We need to check that both TIPC_NLA_NET_NODEID and TIPC_NLA_NET_NODEID_W1
are present.
We also need to make sure userland provided u64 attributes.
Fixes: d50ccc2d39 ("tipc: add 128-bit node identifier")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Jon Maloy <jon.maloy@ericsson.com>
Cc: Ying Xue <ying.xue@windriver.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Before syzbot/KMSAN bites, add the missing policy for TIPC_NLA_NET_ADDR
Fixes: 27c2141672 ("tipc: add net set to new netlink api")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Jon Maloy <jon.maloy@ericsson.com>
Cc: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Tuong Lien
Jon Maloy
Taehee Yoo
Sabrina Dubroca
Tung Nguyen
John Rutherford
Hoang Le
David S. Miller
Matt Bennett
Colin Ian King
Geert Uytterhoeven
Eric Dumazet
Jiri Pirko
Xin Long
Chris Packham
Taras Kondratiuk
Christophe JAILLET
Linus Torvalds
Matteo Croce
Mauro Carvalho Chehab
Thomas Gleixner
Junwei Hu
Parthasarathy Bhuvaragan
Johannes Berg
Michal Kubecek
Jie Liu
David Ahern
Wei Yongjun
Erik Hugne
Kangjie Lu
Zhaolong Zhang
Gustavo A. R. Silva
YueHaibing
Ying Xue
Cong Wang
Aditya Pakki
Zhenbo Gao
Jon Maloy
LUU Duc Canh
David Howells
Karsten Graul
Guoqing Jiang
Parthasarathy Bhuvaragan
Haiqing Bai
Christoph Hellwig
Jia-Ju Bai
GhantaKrishnamurthy MohanKrishna
Kees Cook