* 'agp-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/agp-2.6:
agp/intel-agp: Set dma_mask for capable chipsets before agp_add_bridge()
We should set this before calling agp_add_bridge() so that it's done
before we map the scratch page too.
This should probably fix the regression reported as k.o. bug #14627.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (42 commits)
cxgb3: fix premature page unmap
ibm_newemac: Fix EMACx_TRTR[TRT] bit shifts
vlan: Fix register_vlan_dev() error path
gro: Fix illegal merging of trailer trash
sungem: Fix Serdes detection.
net: fix mdio section mismatch warning
ppp: fix BUG on non-linear SKB (multilink receive)
ixgbe: Fixing EEH handler to handle more than one error
net: Fix the rollback test in dev_change_name()
Revert "isdn: isdn_ppp: Use SKB list facilities instead of home-grown implementation."
TI Davinci EMAC : Fix Console Hang when bringing the interface down
smsc911x: Fix Console Hang when bringing the interface down.
mISDN: fix error return in HFCmulti_init()
forcedeth: mac address fix
r6040: fix version printing
Bluetooth: Fix regression with L2CAP configuration in Basic Mode
Bluetooth: Select Basic Mode as default for SOCK_SEQPACKET
Bluetooth: Set general bonding security for ACL by default
r8169: Fix receive buffer length when MTU is between 1515 and 1536
can: add the missing netlink get_xstats_size callback
...
Calling the START_ISO ioctl with a nonnegative cycle paramater has
never worked. Last night I got around to figuring out why. Most of
this patch is a big comment explaining why we enable an interrupt
source then don't actually do anything when we get one. As the
comment says, we should do more, but we don't have a way to tell
userspace what happened. . .
Signed-off-by: Jay Fenlason <fenlason@redhat.com>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de> (edited comment)
* 'sh/for-2.6.32' of git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6:
sh: Fixup last users of irq_chip->typename
uio: pm_runtime_disable is needed if failed
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty-2.6:
tty: cp210x: Fix carrier handling
tty_port: If we are opened non blocking we still need to raise the carrier
unmap Rx page only when guaranteed that this page won't be
used anymore to allocate rx page chunks.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The TRT bit shifts were reversed for EMAC4 and non-EMAC4 during the
port from ibm_emac to ibm_newemac. This patch corrects that error.
Signed-off-by: Dave Mitchell <dmitchell@appliedmicro.com>
Acked-by: Feng Kan <fkan@appliedmicro.com>
Acked-by: Prodyut Hazarika <phazarika@appliedmicro.com>
Acked-by: Stefan Roese <sr@denx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Dave,
Attached is an update of my patch against the cpufreq fixes branch.
Before applying the patch I compiled and booted the tree to see if the panic
was still there -- to my surprise it was not. This is because of the conversion
of cpufreq_cpu_governor to a char[].
While the panic is kaput, the problem of stale data continues and my patch is
still valid. It is possible to end up with the wrong governor after hotplug
events because CPUFREQ_DEFAULT_GOVERNOR is statically linked to a default,
while the cpu siblings may have had a different governor assigned by a user.
ie) the patch is still needed in order to keep the governors assigned
properly when hotplugging devices
Signed-off-by: Prarit Bhargava <prarit@redhat.com>
Signed-off-by: Dave Jones <davej@redhat.com>
ondemand and conservative governors are messing up time units in the
code path where NO_HZ is not enabled and ignore_nice is set. The walltime
idletime stored is in jiffies and nice time calculation is happening in
microseconds.
The problem was reported and diagnosed by Alexander here.
http://marc.info/?l=linux-kernel&m=125752550404513&w=2
The patch below fixes this thinko.
Reported-by: Alexander Miller <Miller@fmi.uni-stuttgart.de>
Tested-by: Alexander Miller <Miller@fmi.uni-stuttgart.de>
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Dave Jones <davej@redhat.com>
Currently on governer backup/restore path we storing governor's pointer.
This is wrong because one may unload governor's module after cpu goes
offline. As result use-after-free will take place on restored cpu.
It is not easy to exploit this bug, but still we have to close this
issue ASAP. Issue was introduced by following commit
084f349394
##TESTCASE##
#!/bin/sh -x
modprobe acpi_cpufreq
# Any non default governor, in may case it is "ondemand"
modprobe cpufreq_ondemand
echo ondemand > /sys/devices/system/cpu/cpu0/cpufreq/scaling_governor
rmmod acpi_cpufreq
rmmod cpufreq_ondemand
modprobe acpi_cpufreq # << use-after-free here.
Signed-off-by: Dmitry Monakhov <dmonakhov@openvz.org>
Signed-off-by: Dave Jones <davej@redhat.com>
The return should be negative on errors
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Cc: Sudhakar Rajashekhara <sudhakar.raj@ti.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Return a negative error value instead of a positive
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: dmitry pervushin <dpervushin@embeddedalley.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add D-Link DWM-162-U5 device id 1e0e:ce16 into option driver. The device
has 4 interfaces, of which 1 is handled by storage and the other 3 by
option driver.
The device appears first as CD-only 05c6:2100 device and must be
switched to 1e0e:ce16 mode either by using "eject CD" or usb_modeswitch.
The MessageContent for usb_modeswitch.conf is:
"55534243e0c26a85000000000000061b000000020000000000000000000000"
Signed-off-by: Zhang Le <r0bertz@gentoo.org>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1299b) fixes a bug in an error-handling path of usbmon's
binary interface. The storage area for URB data is divided into
fixed-size blocks. If an URB's data can't be copied, the area
reserved for it should be decreased to the size of the truncated
information (rounded up to a block boundary). Rounding up the amount
to be removed and subtracting it from the reserved size is definitely
the wrong thing to do.
Also, when the data for an isochronous URB can't be copied, we can
still copy the isoc packet descriptors. In fact the current code does
copy the descriptors, but then sets the capture length to 0 so they
remain inaccessible. The capture length should be reduced to the
length of the descriptors, not set to 0.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Pete Zaitcev <zaitcev@redhat.com>
CC: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The scratchpad_free() function uses xhci->page_size to free some memory
with pci_free_consistent(). However, the page_size is set to zero before
the call, causing kernel oopses on driver unload. Call scratchpad_free()
before setting xhci->page_size to zero.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Acked-by: John Youn <John.Youn@synopsys.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The trb_in_td() function in the xHCI driver is supposed to translate a
physical transfer buffer request (TRB) into a virtual pointer to the ring
segment that TRB is in.
Unfortunately, a mistake in this function may cause endless loops as the
driver searches through the linked list of ring segments over and over
again. Fix a couple bugs that may lead to loops or bad output:
1. Bail out if we get a NULL pointer when translating the segment's
private structure and the starting DMA address of the segment chunk. If
this happens, we've been handed a starting TRB pointer from a different
ring.
2. Make sure the function works when there's multiple segments in the
ring. In the while loop to search through the ring segments, use the
current segment variable (cur_seg), rather than the starting segment
variable (start_seg) that is passed in.
3. Stop searching the ring if we've run through all the segments in the
ring.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
If the xHCI driver fails during the memory initialization, xhci->ir_set
may not be a valid pointer. Check that it points to valid DMA'able memory
before writing to that address during the memory freeing process.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Am Donnerstag, 10. September 2009 15:43:53 schrieb Dietmar Hilbrich:
> Hello,
>
> i have the following problem with the cdc-acm - driver:
>
> I'm using the driver with an "Ericsson F3507G" on a Thinkpad T400.
>
> If a disable the device (with the RFKill-Switch) while it is used by a
> programm like ppp, the driver doesn't seem to correctly clean up the tty,
> even after the program has been closed)
>
> The tty is still active (e.g. there still exists an entry in
> /sys/dev/char/166:0 if ttyACM0 was used) and if a reacticate the device,
> this device entry will be skipped and the Device-Nodes ttyACM1, ttyACM2
> and ttyACM3 will be used.
>
> This problem was introduced with the commit
> 10077d4a66 (before 2.6.31-rc1) and still
> exists in 2.6.31.
>
> I was able the fix this problem with the following patch:
>
> diff --git a/drivers/usb/class/cdc-acm.c b/drivers/usb/class/cdc-acm.c
> index 2bfc41e..0970d2f 100644
> --- a/drivers/usb/class/cdc-acm.c
> +++ b/drivers/usb/class/cdc-acm.c
> @@ -676,6 +676,7 @@ static void acm_tty_hangup(struct tty_struct *tty)
> struct acm *acm = tty->driver_data;
> tty_port_hangup(&acm->port);
> acm_port_down(acm, 0);
> + acm_tty_unregister(acm);
> }
I have the same problem with cdc-acm (I'm using a Samsung SGH-U900): when I
unplug it from the USB port during a PPP connection, the ppp daemon gets the
hangup correctly (and closes the device), but the struct acm corresponding to
the device disconnected is not freed. Hence reconnecting the device results in
creation of /dev/ttyACM(x+1). The same happens when the system is hibernated
during a PPP connection.
This memory leak is due to the fact that when the tty is hung up,
tty_port_close_start() returns always zero, and acm_tty_close() never reaches
the point where acm_tty_unregister() is called.
Here is a fix for this.
Signed-off-by: Francesco Lavra <francescolavra@interfree.it>
Acked-by: Oliver Neukum <oliver@neukum.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
If acm_rx_tasklet() gets called before tty_port_block_til_ready()
returns, then bulk IN urbs may not be sent. This fixes it.
Signed-off-by: Henry Gebhardt <gebhardt@astro.uni-tuebingen.de>
Acked-by: Oliver Neukum <oliver@neukum.org>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The following patch in the driver is required to avoid USB 1.1 device
failures that may occur due to requests from USB OHCI controllers may
be overwritten if the latency for any pending request by the USB
controller is very long (in the range of milliseconds).
Signed-off-by: Libin Yang <libin.yang@amd.com>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Original discussion:
http://thread.gmane.org/gmane.linux.usb.general/23217/focus=23248
or
http://marc.info/?l=linux-usb&m=125553790714133&w=29a68e39d4a broke carrier handling so that a
cp210x setup which needed the carrier lines set up (non CLOCAL) which did
not make a call which set the termios bits left the lines down even if
CLOCAL was not asserted.
Fix this not by reverting but by adding the proper dtr_rts and
carrier_raised methods. This both sets the modem lines properly and also
implements the correct blocking semantics for the port as required by
POSIX.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Reported-by: Karl Hiramoto <karl@hiramoto.org>
Tested-by: Karl Hiramoto <karl@hiramoto.org>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Original discussion:
http://thread.gmane.org/gmane.linux.usb.general/23217/focus=23248
or
http://marc.info/?l=linux-usb&m=125553790714133&w=2
The tty_port code inherited a bug common to various drivers it was based
upon. If the tty is opened O_NONBLOCK we do not wait for the carrier to be
raised but we must still raise our modem lines if appropriate.
(There is a second question here about whether we should do so if CLOCAL is
set but that can wait)
Signed-off-by: Alan Cox <alan@linux.intel.com>
Reported-by: Karl Hiramoto <karl@hiramoto.org>
Tested-by: Karl Hiramoto <karl@hiramoto.org>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-rc-fixes-2.6:
[SCSI] bfa: declare MODULE_FIRMWARE
[SCSI] gdth: Prevent negative offsets in ioctl CVE-2009-3080
[SCSI] libsas: do not set res = 0 in sas_ex_discover_dev()
[SCSI] Fix incorrect reporting of host protection capabilities
[SCSI] pmcraid: Fix ppc64 driver build for using cpu_to_le32 on U8 data type
[SCSI] ipr: add workaround for MSI interrupts on P7
[SCSI] scsi_transport_fc: Fix WARN message for FC passthru failure paths
[SCSI] bfa: fix test in bfad_os_fc_host_init()
* master.kernel.org:/home/rmk/linux-2.6-arm:
[ARM] pxa: ensure mfp is in correct range in mfp_{read,write}
[ARM] pxa/hx4700: fix hx4700 touchscreen pressure values
ARM: 5787/1: U300 COH 901 331 fixes
ARM: Fix warning in sa1100-flash.c
[ARM] Kirkwood: disable propagation of mbus error to the CPU local bus
[ARM] pxa: fix incorrect mfp_to_gpio() conversion
[ARM] pxa/colibri: fix AC97 ifdefs and add missing include
[ARM] pxa: fix missing underscores in mfp-pxa910.h
[ARM] pxa: fix interrupts number calculation when CONFIG_PXA_HAVE_ISA_IRQS=y
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/lrg/voltage-2.6:
dereferencing freed memory regulator_fixed_voltage_remove()
regulator: Fix check of unsigned return value and transmit errors in wm831x_gp_ldo_get_mode()
regulator: Handle missing constraints in _regulator_disable()
* 'for-linus' of git://git.o-hand.com/linux-rpurdie-leds:
leds-gpio: fix possible crash on OF device unbinding
backlight: Fix backlight limiting on spitz/corgi devices
backlight: lcd - Fix wrong sizeof
* 'hostprogs-wmissing-prototypes' of git://git.kernel.org/pub/scm/linux/kernel/git/josh/linux-misc:
Makefile: Add -Wmising-prototypes to HOSTCFLAGS
oss: Mark loadhex static in hex2hex.c
dtc: Mark various internal functions static
dtc: Set "noinput" in the lexer to avoid an unused function
drm: radeon: Mark several functions static in mkregtable
arch/sparc/boot/*.c: Mark various internal functions static
arch/powerpc/boot/addRamDisk.c: Mark several internal functions static
arch/alpha/boot/tools/objstrip.c: Mark "usage" static
Documentation/vm/page-types.c: Declare checked_open static
genksyms: Mark is_reserved_word static
kconfig: Mark various internal functions static
kconfig: Make zconf.y work with current bison
We need to look for the 'shared-pins' property to get
this right.
Based upon a patch by Hermann Lauer.
Signed-off-by: David S. Miller <davem@davemloft.net>
This fixes the following warning:
WARNING: drivers/net/phy/built-in.o(.devexit.text+0x70): Section mismatch in reference from the function .mdio_gpio_bus_destroy() to the function .devinit.text:.mdio_gpio_bus_deinit()
The function __devexit .mdio_gpio_bus_destroy() references
a function __devinit .mdio_gpio_bus_deinit().
This is often seen when error handling in the exit function
uses functionality in the init path.
The fix is often to remove the __devinit annotation of
.mdio_gpio_bus_deinit() so it may be used outside an init section.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
PPP does not correctly call pskb_may_pull() on all necessary receive paths
before reading the PPP protocol, thus causing PPP to report seemingly
random 'unsupported protocols' and eventually trigger BUG_ON(skb->len <
skb->data_len) in skb_pull_rcsum() when receiving multilink protocol in
non-linear skbs.
ppp_receive_nonmp_frame() does not call pskb_may_pull() before reading the
protocol number. For the non-mp receive path this is not a problem, as
this check is done in ppp_receive_frame(). For the mp receive path,
ppp_mp_reconstruct() usually copies the data into a new linear skb.
However, in the case where the frame is made up of a single mp fragment,
the mp header is pulled and the existing skb used. This skb was then
passed to ppp_receive_nonmp_frame() without checking if the encapsulated
protocol header could safely be read.
Signed-off-by: Ben McKeegan <ben@netservers.co.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
After commmit 4b77b0a2ba EEH breaks
after the second error, since it calls pci_restore_state()
but it returns 0, since pci->state_saved is false.
So, this patch just call pci_save_state() after pci_restore_state().
Signed-off-by: Breno Leitao <leitao@linux.vnet.ibm.com>
Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Panasonic CF-72 uses 6-byte protocol and does not need to be tied
to a particular port.
Signed-off-by: Abner Holsinger <9zabner@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Commit b7802c5c1e ("Input: psmouse - use boolean type") caused the
synaptics_hardware variable to be completely useless, as it is
constantly set to 'true' throughout the whole psmouse_extensions().
This was caused by the following hunk in the commit in question
- int synaptics_hardware = 0;
+ bool synaptics_hardware = true;
which is wrong and causes driver to issue extra reset when falling
back to bare PS/2 protocol.
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
This will fix some small issues with the COH 901 331 RTC driver:
- Interrupt is disabled after alarm so that we don't fire
multiple interrupts.
- We return 0 from the coh901331_alarm_irq_enable() ridding
a compile warning.
- We alter the name in the U300 device registry to match that
of the driver so they sucessfully resolve.
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
drivers/mtd/maps/sa1100-flash.c: In function 'sa1100_probe_subdev':
drivers/mtd/maps/sa1100-flash.c:214: warning: format '%d' expects type 'int', but argument 3 has type 'uint64_t'
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Don't dereference drvdata after it has been freed.
regards,
dan carpenter
Signed-off-by: Dan Carpenter <error27@gmail.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
If there are leds present in the OF tree, but the GPIOs for (some) of
them are unavailable, led_data doesn't get populated with correct
devices. Then, on device unbinding, one can crash the kernel.
Workaround this by setting led->gpio to invalid value early.
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Richard Purdie <rpurdie@linux.intel.com>
On spitz (& similar) machines, if battery is running low, backlight
needs
to be limited to lower step. Unfortunately, current code uses &= for
limiting, turning backlight off completely for some backlight settings.
Fix that.
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Richard Purdie <rpurdie@linux.intel.com>
Which is why I have always preferred sizeof(struct foo) over
sizeof(var).
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Richard Purdie <rpurdie@linux.intel.com>
The adt7475 driver creates pwm#_auto_channel_temp attributes instead
of the standard pwm#_auto_channels_temp. Fix it.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Cc: Jordan Crouse <jordan@cosmicpenguin.net>
The comment says that limits are cached for 60 seconds but the code
actually caches them for only 2 seconds. Align the code on the
comment, as 60 seconds makes more sense.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Cc: Jordan Crouse <jordan@cosmicpenguin.net>
The logic of temperature fault flags is wrong, it shows faults when
there are none and vice versa. Fix it.
I can't believe this has been broken since the driver was added, 8
months ago, basically breaking temp1 and temp3, and nobody ever
complained.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Cc: Jordan Crouse <jordan@cosmicpenguin.net>
Avoid registering channels that have zero divider settings in them, as this
will only lead to kernel OOPS from divide-by-zero when the sysfs entry is
read.
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
If ret is unsigned, the checks for negative wm831x_reg_read() return values
are wrong. The error value should be transmitted to its caller, e.g.
wm831x_gp_ldo_get_status() which tests for a negative return value.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
In the NAPI poll function(emac_poll), check for netif_running()
is unnecassary. In addition to associated runtime overhead, it
also results in a continuous softirq loop when the interface is
brought down under heavy traffic(tested wit Traffic Generator).
Once the interface is disabled, the poll function always returns
zero(with the check for netif_running) and napi_complete() would
never get called resulting in softirq loop.
Signed-off-by: Sriramakrishnan <srk@ti.com>
Acked-by: Chaithrika U S <chaithrika@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the NAPI poll function, check for netif_running() is unnecassary.
In addition to associated runtime overhead, it also results in
continuous softirq loop when the interface is brought down under heavy
traffic(tested with Traffic Generator).Once the interface is disabled,
the poll function always returns zero(with the check for netif_running)
and napi_complete() would never get called resulting in softirq loop.
Signed-off-by: Sriramakrishnan <srk@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The returned error should stay negative
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Acked-by: Karsten Keil <keil@b1-systems.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the existing random_ether_addr() to generate random MAC
instead of doing it by-hand.
Signed-off-by: Stanislav O. Bezzubtsev <stas@lvk.cs.msu.su>
Signed-off-by: David S. Miller <davem@davemloft.net>
The version string already contains the printk level
specifying it again results in the following message
being printed:
<6>r6040: RDC R6040 NAPI ...
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
* git://git.infradead.org/users/dwmw2/iommu-2.6.32:
intel-iommu: Support PCIe hot-plug
intel-iommu: Obey coherent_dma_mask for alloc_coherent on passthrough
intel-iommu: Check for 'DMAR at zero' BIOS error earlier.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: psmouse - remove unneeded '\n' from psmouse.proto parameter
Input: atkbd - restore LED state at reconnect
Input: force LED reset on resume
Input: fix locking in memoryless force-feedback devices
* 'for-linus' of git://neil.brown.name/md:
md/raid5: Allow dirty-degraded arrays to be assembled when only party is degraded.
Don't unconditionally set in_sync on newly added device in raid5_reshape
md: allow v0.91 metadata to record devices as being active but not in-sync.
md: factor out updating of 'recovery_offset'.
* 'for-linus' of git://git390.marist.edu/pub/scm/linux-2.6:
[S390] s390: fix single stepping on svc0
[S390] sclp: undo quiesce handler override on resume
[S390] reset cputime accounting after IPL from NSS
[S390] monreader: fix use after free bug with suspend/resume
If the waker is killed before it can replay outstanding URBs, these URBs
won't be freed or will be replayed at the next open. This patch closes
the window by explicitely discarding outstanding URBs.
Signed-off-by: Oliver Neukum <oliver@neukum.org>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In r8169 driver MTU is used to calculate receive buffer size.
Receive buffer size is used to configure hardware incoming packet filter.
For jumbo frames:
Receive buffer size = Max frame size = MTU + 14 (ethernet header) + 4
(vlan header) + 4 (ethernet checksum) = MTU + 22
Bug:
driver for all MTU up to 1536 use receive buffer size 1536
As you can see from formula, this mean all IP packets > 1536 - 22
(for vlan tagged, 1536 - 18 for not tagged) are dropped by hardware
filter.
Example:
host_good> ifconfig eth0 mtu 1536
host_r8169> ifconfig eth0 mtu 1536
host_good> ping host_r8169
Ok
host_good> ping -s 1500 host_r8169
Fail
host_good> ifconfig eth0 mtu 7000
host_r8169> ifconfig eth0 mtu 7000
host_good> ping -s 1500 host_r8169
Ok
Bonus: got rid of magic number 8
Signed-off-by: Raimonds Cicans <ray@apollo.lv>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the missing "get_xstats_size" callback for the
netlink interface, which is required if "fill_xstats" is used,
as pointed out by Patrick McHardy.
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In 2.6.32-rc the new EMS USB CAN driver was contributed and added the Kconfig
entry right behind an entry of the same *vendor*. This teared the SJA1000
based driver selection into pieces.
This fix cleans up the 2.6.32-rc Kconfig files for the CAN drivers and moves
the SJA1000 and USB Kconfig portions into the belonging directories.
As there are many new CAN drivers in the queue getting this cleanup into
2.6.32-rc would massively reduce the problems for the upcoming drivers.
Thanks,
Oliver
Signed-off-by: Oliver Hartkopp <oliver@hartkopp.net>
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Due commit 4b77b0a2ba, it is not more
possible to pci_restore_state() more than once without calling
pci_save_state() in the middle.
Actually running a ethtool test on s2io makes the card inactive,
and it needs to unload/reload the module to fix.
This patch just save the state just after it restore in order to
keep the old behaviour
Signed-off-by: Breno Leitao <leitao@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit b8ecd988b1.
Due to poor API call balancing by me, this commit not only broke ipw2200
if it can't find it's firmware, it broke ipw2100 basically anytime you
removed the module. At this point in the cycle, let's just put it back
to a sane state and try again next time...
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In a system where the ctrl-alt-del init action initiated by signal
quiesce suspends the machine the quiesce handler override for
_machine_restart, _machine_halt and _machine_power_off needs to be
undone, otherwise the override is still present in the resumed
system. The next shutdown would then load the quiesce state psw
instead of performing the correct shutdown action.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The monreader device driver doesn't set dev->driver_data to NULL after
freeing the corresponding data structure. This leads to a use after
free bug in the freeze/thaw suspend/resume functions after the device
has been opened and closed once. Fix this by clearing dev->driver_data
in the close() function.
Signed-off-by: Gerald Schaefer <gerald.schaefer@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
No need to export those device attributes.
In fact, without this patch, we can trip over a build error if cciss
is a built-in and another driver also declares and exports attributes
with the same name.
You'll see errors like:
drivers/scsi/built-in.o: multiple definition of `dev_attr_lunid'
drivers/block/built-in.o: first defined here
Cc: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: Alex Chiang <achiang@hp.com>
Cc: <mike.miller@hp.com>
Cc: Jens Axboe <jens.axboe@oracle.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
The get parameter function should return a string without a life-feed.
Otherwise you'll see additional empty line in sysfs parameters file.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Even though input core tells us to restore LED state and repeat rate
at resume keyboard may be reconnected either by request from userspace
(via sysfs) or just by pulling it from the box and plugging it back in.
In these cases we still need to restore state ourselves.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
We should be sending EV_LED event down to drivers upon resume even in cases
when in-kernel state of the LED is off since device could come up with some
leds turned on.
Reported-and-tested-by: Mikko Vinni <mmvinni@yahoo.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Normally is it not safe to allow a raid5 that is both dirty and
degraded to be assembled without explicit request from that admin, as
it can cause hidden data corruption.
This is because 'dirty' means that the parity cannot be trusted, and
'degraded' means that the parity needs to be used.
However, if the device that is missing contains only parity, then
there is no issue and assembly can continue.
This particularly applies when a RAID5 is being converted to a RAID6
and there is an unclean shutdown while the conversion is happening.
So check for whether the degraded space only contains parity, and
in that case, allow the assembly.
Signed-off-by: NeilBrown <neilb@suse.de>
When a reshape finds that it can add spare devices into the array,
those devices might already be 'in_sync' if they are beyond the old
size of the array, or they might not if they are within the array.
The first case happens when we change an N-drive RAID5 to an
N+1-drive RAID5.
The second happens when we convert an N-drive RAID5 to an
N+1-drive RAID6.
So set the flag more carefully.
Also, ->recovery_offset is only meaningful when the flag is clear,
so only set it in that case.
This change needs the preceding two to ensure that the non-in_sync
device doesn't get evicted from the array when it is stopped, in the
case where v0.90 metadata is used.
Signed-off-by: NeilBrown <neilb@suse.de>
This is a combination that didn't really make sense before.
However when a reshape is converting e.g. raid5 -> raid6, the extra
device is not fully in-sync, but is certainly active and contains
important data.
So allow that start to be meaningful and in particular get
the 'recovery_offset' value (which is needed for any non-in-sync
active device) from the reshape_position.
Signed-off-by: NeilBrown <neilb@suse.de>
Add new CPU host bridge id, needed for support Ironlake graphics
device with it. No change for graphics device itself, so no need to
update drm/i915.
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Add more display registers save/restore to fix unstable issues
during S4 testing on Ironlake. And DPLL_B_MD should not be restored
on Ironlake.
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
The master irq control in DE must be disabled before irq handling,
and enable after the process. This fixes the irq stall issue on
Ironlake.
Cc: Stable Team <stable@kernel.org>
Signed-off-by: Zou, Nanhai <nanhai.zou@intel.com>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
PPS events must be recorded according to PPS's mode settings.
If a process asks for (i.e.) capture-assert events only, when the PPS
client calls the pps_event() function to save the current PPS event, we
should verify the event type and then discard unwanted ones.
Also, without this patch userland processes waiting for a specific PPS
event (assert or clear but not both) may be awakened at wrong time.
Signed-off-by: Rodolfo Giometti <giometti@linux.it>
Tested-by: William S. Brasher <billb958@door.net>
Tested-by: Reg Clemens <clemens@dwf.com>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Userland programs may read/write PPS parameters at same time and these
operations may corrupt PPS data.
Signed-off-by: Rodolfo Giometti <giometti@linux.it>
Tested-by: Reg Clemens <clemens@dwf.com>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
TASK_INTERRUPTIBLE and friends are now only available after including
<linux/sched.h>, so include it when needed.
bus_id is no longer available/necessary, so remove that.
Android pmem driver is not available in mainline, so remove its hooks
from drivers/video.
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In case of failure, device_create() returns not NULL but the error code.
The current code checks for non-NULL though which causes kernel oops in
sysfs_create_group() when device_create() fails. Check for error using
IS_ERR() and propagate the error value using PTR_ERR() instead of fixed
-ENODEV code returned now...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
v3020_mmio_read_bit() always returns 0 when left_shift > 7.
v3020_mmio_read_bit()'s return type is (unsigned char). The code returns
a value masked by (1 << left_shift) that is casted to the return type. If
left_shift is larger than 7, the cast will always result in a 0 return
value. The problem was discovered with left_shift = 16, and the included
patch corrects the problem.
The bug was introduced in the last (Apr 3 2009) commit of the file, kernel
versions 2.6.30 and later.
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Paul Gortmaker <p_gortmaker@yahoo.com>
Cc: Raphael Assenat <raph@8d.com>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
drivers/rtc/rtc-vr41xx.c: In function 'vr41xx_rtc_irq_set_freq':
drivers/rtc/rtc-vr41xx.c:217: warning: comparison of distinct pointer types lacks a cast
drivers/rtc/rtc-vr41xx.c:217: warning: right shift count >= width of type
drivers/rtc/rtc-vr41xx.c:217: warning: passing argument 1 of '__div64_32' from incompatible pointer type
include/asm-generic/div64.h:35: note: expected 'uint64_t *' but argument is of type 'long unsigned int *'
Signed-off-by: Yoichi Yuasa <yuasa@linux-mips.org>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Paul Gortmaker <p_gortmaker@yahoo.com>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The config FB_PRE_INIT_FB entry in drivers/video/Kconfig pushes all entries
below it out of the menuconfig selection. Fix this.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This seems to be a different model (with a different PCI ID) than the
"Quatro" card that is also in the list.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
struct uart_port::iobase is unsigned long, so use %lx as printk format
specifier.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
According to Documentation/rtc.txt, RTC_WKALM_SET sets the alarm time and
enables/disables the alarm. We implement RTC_WKALM_SET through
pcf50633_rtc_set_alarm. The enabling/disabling part was missing.
Signed-off-by: Werner Almesberger <werner@openmoko.org>
Reported-by: Michael 'Mickey' Lauer <mickey@openmoko.org>
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Cc: Paul Gortmaker <p_gortmaker@yahoo.com>
Cc: Balaji Rao <balajirrao@openmoko.org>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The PCF50633 stores a month value of 1-12, but the kernel wants 0-11.
Signed-off-by: Rask Ingemann Lambertsen <rask@sygehus.dk>
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Cc: Paul Gortmaker <p_gortmaker@yahoo.com>
Cc: Balaji Rao <balajirrao@openmoko.org>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
at91sam9g45 non ES lots have an alternate pixel clock calculation formula.
Introduce this one with condition on the cpu_is_xxxxx() macros.
Newer 9g45 SOC will not have good pixel clock calculation without this
fix.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: Krzysztof Helt <krzysztof.h1@wp.pl>
Cc: Haavard Skinnemoen <hskinnemoen@atmel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix wrong bit mask for blanking register. Due to the error a CRT monitor
blanks off due to wrong frequency (out of range) instead of PM signal
(vertical and horizontal frequencies cut off).
Just compare the mask with bits set in the switch(blank) clause below the
changed line.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Remove fb_save_state() and fb_restore_state operations from frame buffer layer.
They are used only in two drivers:
1. savagefb - and cause bug #11248
2. uvesafb
Usage of these operations is misunderstood in both drivers so kill these
operations, fix the bug #11248 and avoid confusion in the future.
Tested on Savage 3D/MV card and the patch fixes the bug #11248.
The frame buffer layer uses these funtions during switch between graphics
and text mode of the console, but these drivers saves state before
switching of the frame buffer (in the fb_open) and after releasing it (in
the fb_release). This defeats the purpose of these operations.
Addresses http://bugzilla.kernel.org/show_bug.cgi?id=11248
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Reported-by: Jochen Hein <jochen@jochen.org>
Tested-by: Jochen Hein <jochen@jochen.org>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Michal Januszewski <spock@gentoo.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
To support PCIe hot plug in IOMMU, we register a notifier to respond to device
change action.
When the notifier gets BUS_NOTIFY_UNBOUND_DRIVER, it removes the device
from its DMAR domain.
A hot added device will be added into an IOMMU domain when it first does IOMMU
op. So there is no need to add more code for hot add.
Without the patch, after a hot-remove, a hot-added device on the same
slot will not work.
Signed-off-by: Fenghua Yu <fenghua.yu@intel.com>
Tested-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The model for IOMMU passthrough is that decent devices that can cope
with DMA to all of memory get passthrough; crappy devices with a limited
dma_mask don't -- they get to use the IOMMU anyway.
This is done on the basis that IOMMU passthrough is usually wanted for
performance reasons, and it's only the decent PCI devices that you
really care about performance for, while the crappy 32-bit ones like
your USB controller can just use the IOMMU and you won't really care.
Unfortunately, the check for this was only looking at dev->dma_mask, not
at dev->coherent_dma_mask. And some devices have a 32-bit
coherent_dma_mask even though they have a full 64-bit dma_mask.
Even more unfortunately, fixing that simple oversight would upset
certain broken HP devices. Not only do they have a 32-bit
coherent_dma_mask, but they also have a tendency to do stray DMA to
unmapped addresses. And then they die when they take the DMA fault they
so richly deserve.
So if we do the 'correct' fix, it'll mean that affected users have to
disable IOMMU support completely on "a large percentage of servers from
a major vendor."
Personally, I have little sympathy -- given that this is the _same_
'major vendor' who is shipping machines which claim to have IOMMU
support but have obviously never _once_ booted a VT-d capable OS to do
any form of QA. But strictly speaking, it _would_ be a regression even
though it only ever worked by fluke.
For 2.6.33, we'll come up with a quirk which gives swiotlb support
for this particular device, and other devices with an inadequate
coherent_dma_mask will just get normal IOMMU mapping.
The simplest fix for 2.6.32, though, is just to jump through some hoops
to try to allocate coherent DMA memory for such devices in a place that
they can reach. We'd use dma_generic_alloc_coherent() for this if it
existed on IA64.
Signed-off-by: Alex Williamson <alex.williamson@hp.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Each device has its own 'recovery_offset' showing how far
recovery has progressed on the device.
As the only real significance of this is that fact that it can
be stored in the metadata and recovered at restart, and as
only 1.x metadata can do this, we were only updating
'recovery_offset' to 'curr_resync_completed' when updating
v1.x metadata.
But this is wrong, and we will shortly make limited use of this
field in v0.90 metadata.
So move the update into common code.
Signed-off-by: NeilBrown <neilb@suse.de>
Rafael debugged a resume-time hang (with oopses in workqueue handling)
on his laptop that was due to the 'waker' workqueue entry being
disconnected and then released without the workqueue entry having been
synchronized.
Several people were involved, with Oleg Nesterov doing a debugging patch
showing what workqueue entry was corrupt etc.
This was a regression introduced by commit 7bee549e19 ("Bluetooth: Add
USB autosuspend support to btusb driver") as Rafael points out (not
actually bisected, but it became clear once the bug was found).
Tested-and-reported-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Oliver Neukum <oliver@neukum.org>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Tejun Heo <tj@kernel.org>
Cc: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6:
x86/PCI: Adjust GFP mask handling for coherent allocations
PCI ASPM: fix oops on root port removal
* 'drm-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6: (52 commits)
drm/kms: Init the CRTC info fields for modes forced from the command line.
drm/radeon/r600: CS parser updates
drm/radeon/kms: add debugfs for power management for AtomBIOS devices
drm/radeon/kms: initial mode validation support
drm/radeon/kms/atom/dce3: call transmitter init on mode set
drm/radeon/kms: store detailed connector info
drm/radeon/kms/atom/dce3: fix up usPixelClock calculation for Transmitter tables
drm/radeon/kms/r600: fix rs880 support v2
drm/radeon/kms/r700: fix some typos in chip init
drm/radeon/kms: remove some misleading debugging output
drm/radeon/kms: stop putting VRAM at 0 in MC space on r600s.
drm/radeon/kms: disable D1VGA and D2VGA if enabled
drm/radeon/kms: Don't RMW CP_RB_CNTL
drm/radeon/kms: fix coherency issues on AGP cards.
drm/radeon/kms: fix rc410 suspend/resume.
drm/radeon/kms: add quirk for hp dc5750
drm/radeon/kms/atom: fix potential oops in spread spectrum code
drm/kms: typo fix
drm/radeon/kms/atom: Make card_info per device
drm/radeon/kms/atom: Fix DVO support
...
* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-2.6: (27 commits)
V4L/DVB (13314): saa7134: set ts_force_val for the Hauppauge WinTV HVR-1150
V4L/DVB (13313): saa7134: add support for FORCE_TS_VALID mode for mpeg ts input
V4L/DVB (13311): uvcvideo: Fix compilation warning with 2.6.32 due to type mismatch with abs()
V4L/DVB (13309): uvcvideo: Ignore the FIX_BANDWIDTH for compressed video
V4L/DVB (13287): ce6230 - saa7164-cmd: Fix wrong sizeof
V4L/DVB (13286): pxa-camera: Fix missing sched.h
V4L/DVB (13264): gspca_mr97310a: Change vstart for CIF sensor type 1 cams
V4L/DVB (13257): gspca - m5602-s5k4aa: Add vflip for Fujitsu Amilo Xi 2528
V4L/DVB (13256): gspca - m5602-s5k4aa: Add another MSI GX700 vflip quirk
V4L/DVB (13255): gspca - m5602-s5k4aa: Add vflip quirk for the Bruneinit laptop
V4L/DVB (13240): firedtv: fix regression: tuning fails due to bogus error return
V4L/DVB (13237): firedtv: length field corrupt in ca2host if length>127
V4L/DVB (13230): s2255drv: Don't conditionalize video buffer completion on waiting processes
V4L/DVB (13202): smsusb: add autodetection support for three additional Hauppauge USB IDs
V4L/DVB (13190): em28xx: fix panic that can occur when starting audio streaming
V4L/DVB (13170): bttv: Fix reversed polarity error when switching video standard
V4L/DVB (13169): bttv: Fix potential out-of-order field processing
V4L/DVB (13167): pt1: Fix a compile error on arm
V4L/DVB (13132): fix use-after-free Oops, resulting from a driver-core API change
V4L/DVB (13131): pxa_camera: fix camera pixel format configuration
...
A negative offset could be used to index before the event buffer and
lead to a security breach.
Signed-off-by: Dave Jones <davej@redhat.com>
Cc: Stable Tree <stable@kernel.org>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Now that input core acquires dev->event_lock spinlock and disables
interrupts when propagating input events, using spin_lock_bh() in
ff-memless driver is not allowed. Actually, the timer_lock itself
is not needed anymore, we should simply use dev->event_lock
as well.
Also do a small cleanup in force-feedback core.
Reported-by: kerneloops.org
Reported-by: http://www.kerneloops.org/searchweek.php?search=ml_ff_set_gain
Reported-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Turn on RTS/CTS for HT to prevent uCode TX fifo underrun
This is fix for
http://bugzilla.intellinuxwireless.org/show_bug.cgi?id=2103
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Tested-by: Jiajia Zheng <jiajia.zheng@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When 802.11g was introduced, we had RTS/CTS and CTS-to-Self protection
mechanisms. In an HT Beacon, HT stations use the "Operating Mode" field
in the HT Information Element to determine whether or not to use
protection.
The Operating Mode field has 4 possible settings: 0-3:
Mode 0: If all stations in the BSS are 20/40 MHz HT capable, or if the
BSS is 20/40 MHz capable, or if all stations in the BSS are 20 MHz HT
stations in a 20 MHz BSS
Mode 1: used if there are non-HT stations or APs using the primary or
secondary channels
Mode 2: if only HT stations are associated in the BSS and at least one
20 MHz HT station is associated.
Mode 3: used if one or more non-HT stations are associated in the BSS.
When in operating modes 1 or 3, and the Use_Protection field is 1 in the
Beacon's ERP IE, all HT transmissions must be protected using RTS/CTS or
CTS-to-Self.
By default, CTS-to-self is the preferred protection mechanism for less
overhead and higher throughput; but using the full RTS/CTS will better
protect the inner exchange from interference, especially in
highly-congested environment.
For 6000 series WIFI NIC, RTS/CTS protection mechanism is the
recommended choice for HT traffic based on the HW design.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Configuration of wake-on-lan for unicast, multicast, broadcast, physical
activity was not working. Kernel panic issue was there when user tries to
disable WOL. Fixed them.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Due to a missing header include, sparse generates the following warnings:
CHECK drivers/net/wireless/rtl818x/rtl8187_rfkill.c
warning: symbol 'rtl8187_rfkill_init' was not declared. Should it be static?
warning: symbol 'rtl8187_rfkill_poll' was not declared. Should it be static?
warning: symbol 'rtl8187_rfkill_exit' was not declared. Should it be static?
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Setup the GPIOs for the BenQ Joybook netbook.
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add GPIO configuration for the Compaq CQ60 laptop
Reported-by: David Dreggors <ddreggors@jumptv.com>
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We should not zero out the multicast hash when configuring
the operating mode, since a zero value means all multicast
frames will get dropped. Also, ath5k_mode_setup() gets
called after any reset, so the hash already set up in
configure_filter() is lost.
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ops->set_tim() must be atomic, so b43 trying to acquire a mutex leads
to a kernel crash. This patch trades an easy to trigger crash in AP
mode for an unlikely race condition. According to Michael, the real
fix would be to allow set_tim() to sleep, since b43 is not the only
driver that needs to sleep in all callbacks.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The scan function was using 32 bit access which does not
work on 16bit CF cards.
This patch corrects this by doing two 16 bit reads like
ssb_pcmcia_read32 already does.
mb -- Removed locking. That early in init there's no need for locking.
Signed-off-by: Martin Fuzzey <mfuzzey@gmail.com>
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The commit d79c326 ("gpio-addr-flash: new driver for GPIO assisted
flash addressing") removed two lines from the Makefile by accident.
Though I'm not sure how this accident happened, this patch reverts the
removal.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Chris Wright has some patches which let us fall back to swiotlb nicely
if IOMMU initialisation fails. But those are a bit much for 2.6.32.
Instead, let's shift the check for the biggest problem, the HP and Acer
BIOS bug which reports a DMAR at physical address zero. That one can
actually be checked much earlier -- before we even admit to having
detected an IOMMU in the first place. So the swiotlb init goes ahead as
we want.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
* 'i2c-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jdelvare/staging:
i2c: Add an interface to lock/unlock an I2C bus segment
i2c-piix4: Modify code name SB900 to Hudson-2
* 'for-linus' of git://neil.brown.name/md:
md/raid5: make sure curr_sync_completes is uptodate when reshape starts
md: don't clear endpoint for resync when resync is interrupted.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (34 commits)
net/fsl_pq_mdio: add module license GPL
can: fix WARN_ON dump in net/core/rtnetlink.c:rtmsg_ifinfo()
can: should not use __dev_get_by_index() without locks
hisax: remove bad udelay call to fix build error on ARM
ipip: Fix handling of DF packets when pmtudisc is OFF
qlge: Set PCIe reset type for EEH to fundamental.
qlge: Fix early exit from mbox cmd complete wait.
ixgbe: fix traffic hangs on Tx with ioatdma loaded
ixgbe: Fix checking TFCS register for TXOFF status when DCB is enabled
ixgbe: Fix gso_max_size for 82599 when DCB is enabled
macsonic: fix crash on PowerBook 520
NET: cassini, fix lock imbalance
ems_usb: Fix byte order issues on big endian machines
be2net: Bug fix to send config commands to hardware after netdev_register
be2net: fix to set proper flow control on resume
netfilter: xt_connlimit: fix regression caused by zero family value
rt2x00: Don't queue ieee80211 work after USB removal
Revert "ipw2200: fix oops on missing firmware"
decnet: netdevice refcount leak
netfilter: nf_nat: fix NAT issue in 2.6.30.4+
...
* 'sh/for-2.6.32' of git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6:
sh: Replace old style lock initializer
sh: Account for cache aliases in flush_icache_range()
sh: unwinder: Fix up invalid PC refetch in dwarf unwinder.
serial: sh-sci: disable callback typo fix
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6:
ACPI: sleep: another HP/Compaq DMI entries for init_set_sci_en_on_resume
ACPI: add DMI entry for SCI_EN resume quirk on HP dv4
thermal: sysfs-api.txt - document passive attribute for thermal zones
thermal: sysfs-api.txt - reformat for improved readability
acpi: thermal: Add EOL to the trip_point_N_type strings
ACPI: Move dereference after NULL test
ACPICA: avoid "Info: mapping multiple BARs. Your kernel is fine."
ACPI: add __cpuinit to acpi_processor_add()
acpi-power-meter: Don't leak ACPI error codes to userspace
eeepc-laptop: don't enable camera at startup if it's already on.
Revert "eeepc-laptop: Prevent a panic when disabling RT2860 wireless when associated"
ACPI: clean up video.c boundary checks and types
or it will taint the kernel and fail to load becuase
of_address_to_resource() is GPL only.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
On older kernels, e.g. 2.6.27, a WARN_ON dump in rtmsg_ifinfo()
is thrown when the CAN device is registered due to insufficient
skb space, as reported by various users. This patch adds the
rtnl_link_ops "get_size" to fix the problem. I think this patch
is required for more recent kernels as well, even if no WARN_ON
dumps are triggered. Maybe we also need "get_xstats_size" for
the CAN xstats.
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Hauppauge WinTV HVR-1150 retail boards require the FORCE_TS_VALID bit
to be set in order to function properly. This change will work on the early
revisions on the board as well, but the final revision will not function
without this change.
Signed-off-by: Michael Krufky <mkrufky@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
When FORCE_TS_VALID mode is enabled, the saa713x will accept MPEG TS input
without requiring TS_VALID set high. This is required for some new boards
to function properly, due to the hardware design implementation.
The configuration is toggled within the board setup configuration. Boards
that do not have this bit set will function as before with no change.
Signed-off-by: Michael Krufky <mkrufky@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The abs() macro has changed in 2.6.32 and returns a long instead of an
int. Fix the driver to avoid compilation warnings.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The FIX_BANDWIDTH quirk tries to work around cameras requesting the
maximum bandwidth regardless of the image size by computing a bandwidth
estimate. This works only for uncompressed frames.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Which is why I have always preferred sizeof(struct foo) over
sizeof(var).
Cc: Antti Palosaari <crope@iki.fi>
Acked-by: Steven Toth <stoth@kernellabs.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Douglas Schilling Landgraf <dougsland@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
gspca_mr97310a: Change vstart for CIF sensor type 1 cams
This fixes the distortion at the end of the frame, and avoids the bad frame
dropping done because of this distortion, trippling the framerate!
Signed-off-by: Theodore Kilgore <kilgota@banach.math.auburn.edu>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Adds a vflip quirk for the Fujitsu Amilo Xi 2528. Thanks to Evgeny for the report.
Signed-off-by: Erik Andrén <erik.andren@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Adds another vflip quirk for the MSI GX700.
Thanks to John Katzmaier for reporting.
Signed-off-by: Erik Andrén <erik.andren@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Adds a vflip quirk for the Bruneinit laptop. Thanks to Jörg for the report
Signed-off-by: Erik Andrén <erik.andren@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Since 2.6.32(-rc1), DVB core checks the return value of
dvb_frontend_ops.set_frontend. Now it becomes apparent that firedtv
always returned a bogus value from its set_frontend method.
CC: stable@kernel.org
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This solves a problem in firedtv that has become major for Swedish DVB-T
users the last month or so. It will most likely solve issues seen by
other users as well.
If the length of an AVC message is greater than 127, the length field
should be encoded in LV mode instead of V mode. V mode can only be used
if the length is 127 or less. This patch ensures that the CA_PMT
message is always encoded in LV mode so PMT message of greater lengths
can be supported.
Signed-off-by: Henrik Kurelid <henrik@kurelid.se>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The s2255 driver had logic which aborted processing of a video frame
if there was no process waiting on the video buffer in question. That
simply doesn't work when the application is doing things in an
asynchronous manner. If the application went to the trouble to queue
the buffer in the first place, then the driver should always attempt
to complete it - even if the application at that moment has its
attention turned elsewhere. Applications which always blocked waiting
for I/O on the capture device would not have been affected by this.
Applications which *mostly* blocked waiting for I/O on the capture
device probably only would have been somewhat affected (frame lossage,
at a rate which goes up as the application blocks less). Applications
which never blocked on the capture device (e.g. polling only) however
would never have been able to receive any video frames, since in that
case this "is anyone waiting on this?" check on the buffer never would
have evalutated true. This patch just deletes that harmful check
against the buffer's wait queue.
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
CC: stable@kernel.org
Add support for three new Hauppauge Device USB IDs:
2040:b900
2040:b910
2040:c000
Signed-off-by: Michael Krufky <mkrufky@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Because the counters were not reset when starting up streaming, they would
be reused from the previous run. This can result in cases such that when the
second instance of streaming starts up, the "cnt" variable in
em28xx_audio_isocirq() can end up being negative, resulting in attempting to
write to memory before the start of runtime->dma_area (as well as having a
negative number of bytes to copy).
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
CC: stable@kernel.org
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The bttv driver function which handles switching of the video standard
(set_tvnorm() in bttv-driver.c) includes a check which can optionally
also reset the cropping configuration to a default value. It is
"optional" based on a comparison of the cropcap parameters of the
previous vs the newly requested video standard. The comparison is
being done with a memcmp(), a function which only returns a true value
if the comparison actually fails.
This if-statement appears to have been written to assume wrong
memcmp() semantics. That is, it was re-initializing the cropping
configuration only if the new video standard did NOT have different
cropcap values. That doesn't make any sense. One definitely should
reset things if the cropcap parameters are different - if there's any
comparison to made at all.
The effect of this problem was that a transition from, say, PAL to
NTSC would leave in place old cropping setup that made sense for the
PAL geometry but not for NTSC. If the application doesn't care about
cropping it also won't try to reset the cropping configuration,
resulting in an improperly cropped video frame. In the case I was
testing this actually caused black video frames to be displayed.
Another interesting effect of this bug is that if one does something
which does NOT change the video standard and this function is run,
then the cropping setup gets reset anyway - again because of the
backwards comparison. It turns out that just running anything which
merely opens and closes the video device node (e.g. v4l-info) will
cause this to happen. One can argue that simply opening the device
node and not doing anything to it should not mess with any of its
state - but because of this behavior, any TV app which does such
things (e.g. xawtv) probably therefore doesn't see the problem.
The solution is to fix the sense of the if-statement. It's easy to
see how this mistake could have been made given how memcmp() works.
The patch is therefore removal of a single "!" character from the
if-statement in set_tvnorm in bttv-driver.c.
Signed-off-by: Mike Isely <isely@pobox.com>
CC: stable@kernel.org
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
There is a subtle interaction in the bttv driver which can result in
fields being repeatedly processed out of order. This is a problem
specifically when running in V4L2_FIELD_ALTERNATE mode (probably the
most common case).
1. The determination of which fields are associated with which buffers
happens in videobuf, before the bttv driver gets a chance to queue the
corresponding DMA. Thus by the point when the DMA is queued for a
given buffer, the algorithm has to do the queuing based on the
buffer's already assigned field type - not based on which field is
"next" in the video stream.
2. The driver normally tries to queue both the top and bottom fields
at the same time (see bttv_irq_next_video()). It tries to sort out
top vs bottom by looking at the field type for the next 2 available
buffers and assigning them appropriately.
3. However the bttv driver *always* actually processes the top field
first. There's even an interrupt set aside for specifically
recognizing when the top field has been processed so that it can be
marked done even while the bottom field is still being DMAed.
Given all of the above, if one gets into a situation where
bttv_irq_next_video() gets entered when the first available buffer has
been pre-associated as a bottom field, then the function is going to
process the buffers out of order. That first available buffer will be
put into the bottom field slot and the buffer after that will be put
into the top field slot. Problem is, since the top field is always
processed first by the driver, then that second buffer (the one after
the first available buffer) will be the first one to be finished.
Because of the strict fifo handling of all video buffers, then that
top field won't be seen by the app until after the bottom field is
also processed. Worse still, the app will get back the
chronologically later bottom field first, *before* the top field is
received. The buffer's timestamps will even be backwards.
While not fatal to most TV apps, this behavior can subtlely degrade
userspace deinterlacing (probably will cause jitter). That's probably
why it has gone unnoticed. But it will also cause serious problems if
the app in question discards all but the latest received buffer (a
latency minimizing tactic) - causing one field to only ever be
displayed since the other is now always late. Unfortunately once you
get into this state, you're stuck this way - because having consumed
two buffers, now the next time around the "first" available buffer
will again be a bottom field and the same thing happens.
How can we get into this state? In a perfect world, where there's
always a few free buffers queued to the driver, it should be
impossible. However if something disrupts streaming, e.g. if the
userspace app can't queue free buffers fast enough for a moment due
perhaps to a CPU scheduling glitch, then the driver can get
momentarily starved and some number of fields will be dropped. That's
OK. But if an odd number of fields get dropped, then that "first"
available buffer might be the bottom field and now we're stuck...
This patch fixes that problem by deliberately only setting up a single
field for one frame if we don't get a top field as the first available
buffer. By purposely skipping the other field, then we only handle a
single buffer thus bringing things back into proper sync (i.e. top
field first) for the next frame. To do this we just drop the few
lines in bttv_irq_next_video() that attempt to set up the second
buffer when that second buffer isn't for the bottom field.
This is definitely a problem in when in V4L2_FIELD_ALTERNATE mode. In
the other modes this change either has no effect or doesn't harm
things any further anyway.
Signed-off-by: Mike Isely <isely@pobox.com>
CC: stable@kernel.org
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The lack of #include <linux/vmalloc.h> caused a compile error on some
architectures.
Signed-off-by: HIRANO Takahito <hiranotaka@zng.info>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Commit b402843787 has broken again re-use of
device objects across device_register() / device_unregister() cycles. Fix
soc-camera by nullifying the struct after device_unregister().
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Fix a bug in cropping calculation, when the client is also scaling the image.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
When we call gspca_frame_add, it returns a pointer to the frame passed in,
unless we call it with LAST_PACKET, when it will return a pointer to a
new frame in which to store the frame data for the next frame.
The frame pointer was not updated in stv06xx and ov518.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
While having tda18271 module set with debug=17 (cal & info prints) and
cal=0 (delay calibration process until first use) - I discovered that
during the calibration process, if the frequency test for 69750000
returned a bcal of 0 (see tda18721-fe.c in tda18271_powerscan func) that
the tuner wouldn't be able to pickup any of the frequencies in the range
(all the other frequencies bands returned bcal=1). I spent some time
going over the code and the NXP's tda18271 spec (ver.4 of it i think) and
adding a lot of debug prints and walking/stepping through the calibration
process. I found that when the powerscan fails to find a frequency, the
rf calibration is not run and the default value is supposed to be used in
its place (pulled from the RF_CAL_map table) - but something was getting
goofed up there.
Now, my c coding skills are very rusty, but i think root of the problem is
a signedness issue with the math operation for calculating the rf_a1 and
rf_a2 values in tda18271_rf_tracking_filters_init func, which results in
values like 20648 for rf_a1 (when it should probably have a value like 0,
or so slightly negative that it should be zero - this bad value for rf_a1
would in turn makes the approx calc within
tda18271c2_rf_tracking_filters_correction go out of whack). The simplest
solution i found was to explicitly convert the signedness of the
denominator to avoid the implicit conversion. The values placed into the
u32 rf_freq array should never exceed about 900mhz, so i think the s32 max
value shouldn't be an issue in this case.
I've tested it out a little, and even when i get a bcal=0 with the
modified code, the default calibration value gets used, rf_a1 is zero, and
the tuner seems to lock on the stream and mythtv seems to play it fine.
Signed-off-by: Seth Barry <seth@cyberseth.com>
Signed-off-by: Michael Krufky <mkrufky@kernellabs.com>
CC: stable@kernel.org
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Multiplication by 62500 causes an overflow in the 32 bit freq variable,
which is later divided by 1000 when using FM radio.
This patch prevents the overflow by scaling the frequency value correctly
upfront. Thanks to Henk Vergonet for spotting the problem and providing
a preliminary patch, which this changeset was based upon.
Cc: Henk Vergonet <Henk.Vergonet@gmail.com>
Signed-off-by: Michael Krufky <mkrufky@kernellabs.com>
CC: stable@kernel.org
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Fixing kernel oops when driver attemps to load xc2028 firmware.
Note by djh: the patch contribute by Martin is a port of a fix I made during
the PCTV 340e development. It's a temporary workaround that fixes a regression
(an OOPS condition) and the real fix should be in the code that manages the
i2c master on the dib7000p. But this fix does address the immmediate
regression and should be merged upstream until we do a cleaner fix.
Signed-off-by: Martin Samek <martin@marsark.sytes.net>
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
CC: stable@kernel.org
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
git commit db48138f6b changed by accident the
assignment of certain USB IDs to their device-specific-handlers.
Thanks to Edward Sheldrake for finding this regression
Signed-off-by: Patrick Boettcher <pboettcher@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Some drivers need to be able to prevent access to an I2C bus segment
for a specific period of time. Add an interface for them to do so
without twiddling with i2c-core internals.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Ben Hutchings <bhutchings@solarflare.com>
The hisax ISDN driver fails to build on ARM with CONFIG_HISAX_ELSA:
| drivers/built-in.o: In function `modem_set_dial':
| drivers/isdn/hisax/elsa_ser.c:535: undefined reference to `__bad_udelay'
| drivers/isdn/hisax/elsa_ser.c:544: undefined reference to `__bad_udelay'
| drivers/built-in.o: In function `modem_set_init':
| drivers/isdn/hisax/elsa_ser.c:486: undefined reference to `__bad_udelay'
| [...]
According to the comment in arch/arm/include/asm/delay.h, __bad_udelay
is specifically designed on ARM to produce a build failure when udelay
is called with a value > 2000.
Signed-off-by: Martin Michlmayr <tbm@cyrius.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This device requires a fundamental reset when recovering from EEH.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This line was accidentally left out of the previous commit #
da03945140 ("qlge: Fix firmware mailbox
command timeout.").
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When ioatdma was loaded we we were unable to transmit traffic. We weren't
using the correct registers in ixgbe_update_tx_dca for 82599 systems.
Likewise in ixgbe_configure_tx() we weren't disabling the arbiter before
modifying MTQC.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When DCB is enabled, the ixgbe_check_tx_hang() should check the corresponding
TC's TXOFF in TFCS based on the TC that the tx ring belongs to. Adds a
function to map from the tx_ring hw reg_idx to the correspodning TC and read
TFCS accordingly.
Signed-off-by: Yi Zou <yi.zou@intel.com>
Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 32k gso_max_size when DCB is enabled is for 82598 only, not for 82599.
Signed-off-by: Yi Zou <yi.zou@intel.com>
Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
No-one seems to know where the PowerBook 500 series store their ethernet
MAC addresses. So, rather than crash, use a MAC address from the SONIC
CAM. Failing that, generate a random one.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stanse found that one error path in cas_open omits to unlock pm_mutex.
Fix that.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
CPC-USB is using a ARM7 core with little endian byte order. The "id" field
in can_msg needs byte order conversion from/to CPU byte order.
Signed-off-by: Sebastian Haas <haas@ems-wuensche.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sending config commands to be2 hardware before netdev_register is
completed, is sometimes causing the async link notification to arrive
even before the driver is ready to handle it. The commands for vlan
config and flow control settings can infact wait till be_open.
This patch takes care of that.
Signed-off-by: Ajit Khaparde <ajitk@serverengines.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If be2 goes into suspend after a user changes the flow control settings,
we are not programming them back after resume. This patch takes care of it.
We now get the flow control settings before going to suspend mode and
then apply them during resume.
Signed-off-by: Ajit Khaparde <ajitk@serverengines.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix the following BUG_ON() problem reported by Alex Chiang.
This problem happened when removing PCIe root port using PCI logical
hotplug operation.
The immediate cause of this problem is that the pointer to invalid
data structure is passed to pcie_update_aspm_capable() by
pcie_aspm_exit_link_state(). When pcie_aspm_exit_link_state() received
a pointer to root port link, it unconfigures the root port link and
frees its data structure at first. At this point, there are not links
to configure under the root port and the data structure for root port
link is already freed. So pcie_aspm_exit_link_state() must not call
pcie_update_aspm_capable() and pcie_config_aspm_path().
This patch fixes the problem by changing pcie_aspm_exit_link_state()
not to call pcie_update_aspm_capable() and pcie_config_aspm_path() if
the specified link is root port link.
------------[ cut here ]------------
kernel BUG at drivers/pci/pcie/aspm.c:606!
invalid opcode: 0000 [#1] SMP DEBUG_PAGEALLOC
last sysfs file: /sys/devices/pci0000:40/0000:40:13.0/remove
CPU 1
Modules linked in: shpchp
Pid: 9345, comm: sysfsd Not tainted 2.6.32-rc5 #98 ProLiant DL785 G6
RIP: 0010:[<ffffffff811df69b>] [<ffffffff811df69b>] pcie_update_aspm_capable+0x15/0xbe
RSP: 0018:ffff88082a2f5ca0 EFLAGS: 00010202
RAX: 0000000000000e77 RBX: ffff88182cc3e000 RCX: ffff88082a33d006
RDX: 0000000000000001 RSI: ffffffff811dff4a RDI: ffff88182cc3e000
RBP: ffff88082a2f5cc0 R08: ffff88182cc3e000 R09: 0000000000000000
R10: ffff88182fc00180 R11: ffff88182fc00198 R12: ffff88182cc3e000
R13: 0000000000000000 R14: ffff88182cc3e000 R15: ffff88082a2f5e20
FS: 00007f259a64b6f0(0000) GS:ffff880864600000(0000) knlGS:0000000000000000
CS: 0010 DS: 0018 ES: 0018 CR0: 000000008005003b
CR2: 00007feb53f73da0 CR3: 000000102cc94000 CR4: 00000000000006e0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000ffff0ff0 DR7: 0000000000000400
Process sysfsd (pid: 9345, threadinfo ffff88082a2f4000, task ffff88082a33cf00)
Stack:
ffff88182cc3e000 ffff88182cc3e000 0000000000000000 ffff88082a33cf00
<0> ffff88082a2f5cf0 ffffffff811dff52 ffff88082a2f5cf0 ffff88082c525168
<0> ffff88402c9fd2f8 ffff88402c9fd2f8 ffff88082a2f5d20 ffffffff811d7db2
Call Trace:
[<ffffffff811dff52>] pcie_aspm_exit_link_state+0xf5/0x11e
[<ffffffff811d7db2>] pci_stop_bus_device+0x76/0x7e
[<ffffffff811d7d67>] pci_stop_bus_device+0x2b/0x7e
[<ffffffff811d7e4f>] pci_remove_bus_device+0x15/0xb9
[<ffffffff811dcb8c>] remove_callback+0x29/0x3a
[<ffffffff81135aeb>] sysfs_schedule_callback_work+0x15/0x6d
[<ffffffff81072790>] worker_thread+0x19d/0x298
[<ffffffff8107273b>] ? worker_thread+0x148/0x298
[<ffffffff81135ad6>] ? sysfs_schedule_callback_work+0x0/0x6d
[<ffffffff810765c0>] ? autoremove_wake_function+0x0/0x38
[<ffffffff810725f3>] ? worker_thread+0x0/0x298
[<ffffffff8107629e>] kthread+0x7d/0x85
[<ffffffff8102eafa>] child_rip+0xa/0x20
[<ffffffff8102e4bc>] ? restore_args+0x0/0x30
[<ffffffff81076221>] ? kthread+0x0/0x85
[<ffffffff8102eaf0>] ? child_rip+0x0/0x20
Code: 89 e5 8a 50 48 31 c0 c0 ea 03 83 e2 07 e8 b2 de fe ff c9 48 98 c3 55 48 89 e5 41 56 49 89 fe 41 55 41 54 53 48 83 7f 10 00 74 04 <0f> 0b eb fe 48 8b 05 da 7d 63 00 4c 8d 60 e8 4c 89 e1 eb 24 4c
RIP [<ffffffff811df69b>] pcie_update_aspm_capable+0x15/0xbe
RSP <ffff88082a2f5ca0>
---[ end trace 6ae0f65bdeab8555 ]---
Reported-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Tested-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
This prevents the rt2x00 driver from queueing ieee80211 work after the
USB card has been removed, preventing a kernel panic.
Signed-off-by: Sean Cross <sean@chumby.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We should not set res to 0 in function sas_ex_discover_dev in order to let
it discover it further when wide port hotplug in .
Signed-off-by: Tom Peng <tom_peng@usish.com>
Signed-off-by: Jack Wang <jack_wang@usish.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Fix a reported ppc64 driver build issue. Removed cpu_to_le32 conversion
usage for flags in struct pmcraid_ioadl_desc. This was breaking the driver build in ppc64.
drivers/scsi/pmcraid.c: In function 'pmcraid_request_sense':
drivers/scsi/pmcraid.c:2254: warning: large integer implicitly truncated
to unsigned type
Signed-off-by: Anil Ravindranath<anil_ravindranath@pmc-sierra.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
This patch adds some additional logic to the interrupt service routine to fix
a potential problem where an MSI interrupt does not get cleared the first time.
Signed-off-by: Wayne Boyer <wayneb@linux.vnet.ibm.com>
Acked-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
This reverts commit 6029336426.
Ok, we really do need to revert this, even with Bart's sis5513.c
fix in there.
The problem is that several driver's ->set_pio_mode() method
depends upon the drive->media type being set properly. Most
of them use this to enable prefetching, which can only be done
for disk media.
But the commit being reverted here calls ->set_pio_mode() before
it's setup. Actually it considers everything disk because that
is the default media type set by ide_port_init_devices_data().
The set of drivers that depend upon the media type in their
->set_pio_method() are:
drivers/ide/alim15x3.c
drivers/ide/it8172.c
drivers/ide/it8213.c
drivers/ide/pdc202xx_old.c
drivers/ide/piix.c
drivers/ide/qd65xx.c
drivers/ide/sis5513.c
drivers/ide/slc90e66.c
And it is possible that we could fix this by guarding the prefetching
and other media dependent setting changes with a test on
IDE_PFLAG_PROBING in hwif->port_flags, that's simply too risky for
2.6.32-rcX and -stable.
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes the missing battery on sleep problem for yet another HP laptop
("HP Pavilion dv4").
Fixes:
http://bugzilla.kernel.org/show_bug.cgi?id=13449
Signed-off-by: Gustavo Maciel Dias Vieira <gustavo@sagui.org>
Signed-off-by: Len Brown <len.brown@intel.com>
This value is visible through sysfs and is used by mdadm
when it manages a reshape (backing up data that is about to be
rearranged). So it is important that it is always correct.
Current it does not get updated properly when a reshape
starts which can cause problems when assembling an array
that is in the middle of being reshaped.
This is suitable for 2.6.31.y stable kernels.
Cc: stable@kernel.org
Signed-off-by: NeilBrown <neilb@suse.de>
If a 'sync_max' has been set (via sysfs), it is wrong to clear it
until a resync (or reshape or recovery ...) actually reached that
point.
So if a resync is interrupted (e.g. by device failure),
leave 'resync_max' unchanged.
This is particularly important for 'reshape' operations that do not
change the size of the array. For such operations mdadm needs to
monitor the reshape taking rolling backups of the section being
reshaped. If resync_max gets cleared, the reshape can get ahead of
mdadm and then the backups that mdadm creates are useless.
This is suitable for 2.6.31.y stable kernels.
Cc: stable@kernel.org
Signed-off-by: NeilBrown <neilb@suse.de>
Generally this is done at post, but might not always be done
with softboot or for connectors on docking stations.
Could probably be done once when the driver loads/resumes
rather than on each mode set.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This will be useful for mode validation and certain
atom tables.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Lots of cases were wrong or missing.
v2: rebased against drm-next
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Make the trip_point_N_type sysfs files return a string ending in EOL for
consistency with other sysfs files.
Signed-off-by: Amit Kucheria <amit.kucheria@canonical.com>
Acked-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Len Brown <len.brown@intel.com>
If the NULL test on pr is needed, then the dereference should be after the
NULL test.
A simplified version of the semantic match that detects this problem is as
follows (http://coccinelle.lip6.fr/):
// <smpl>
@match exists@
expression x, E;
identifier fld;
@@
* x->fld
... when != \(x = E\|&x\)
* x == NULL
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Len Brown <len.brown@intel.com>
This brings some hardware workaround for HDMI port on PCH (Ibex Peak),
which fixes unstable issues like during rotation.
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Ensure that memory mappings created for operation regions
do not cross page boundaries. Crossing a page boundary
while mapping regions can cause warnings if the pages have different attributes.
Such regions are probably BIOS bugs, and this is the workaround.
http://bugzilla.kernel.org/show_bug.cgi?id=14445
[Kernel summit hacking hour]
Signed-off-by: Bob Moore <robert.moore@intel.com>
Acked-by: Suresh Siddha <suresh.b.siddha@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
When the ideal error range can't be reached, this will safely use
a most closed one. Clean up some dumb codes in DPLL function too.
This fixes DPLL clock issue against one monitor at 1680x1050@60hz.
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Annote acpi_processor_add with cpuinit since it calls a cpuinit function
acpi_processor_power_init and fixes a section mismatch warning.
We were warned by the following warning:
LD drivers/acpi/processor.o
WARNING: drivers/acpi/processor.o(.text+0x1829): Section mismatch in
reference from the function acpi_processor_add() to the function
.cpuinit.text:acpi_processor_power_init()
The function acpi_processor_add() references
the function __cpuinit acpi_processor_power_init().
This is often because acpi_processor_add lacks a __cpuinit
annotation or the annotation of acpi_processor_power_init is wrong.
Signed-off-by: Rakib Mullick <rakib.mullick@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Len Brown <len.brown@intel.com>
Linus Torvalds
David Woodhouse
Jay Fenlason
Divy Le Ray
Dave Mitchell
Prarit Bhargava
Pallipadi, Venkatesh
Dmitry Monakhov
Roel Kluin
Zhang Le
Alan Stern
Sarah Sharp
Francesco Lavra
Henry Gebhardt
Libin Yang
Alan Cox
Dan Williams
David S. Miller
Stephen Rothwell
Ben McKeegan
Breno Leitao
Abner Holsinger
Jiri Kosina
Linus Walleij
Russell King
Dan Carpenter
Dmitry Eremin-Solenikov
Pavel Machek
Jean Delvare
Ben Dooks
Mark Brown
Sriram
Stanislav O. Bezzubtsev
Florian Fainelli
Josh Triplett
Oliver Neukum
Raimonds Cicans
Wolfgang Grandegger
Oliver Hartkopp
Larry Finger
John W. Linville
Martin Schwidefsky
Gerald Schaefer
Alex Chiang
Takashi Iwai
Dmitry Torokhov
NeilBrown
Kuninori Morimoto
Zhenyu Wang
Zou, Nanhai
Rodolfo Giometti
Sergei Shtylyov
Scott Valentine
Yoichi Yuasa
Guennadi Liakhovetski
Ladislav Michl
Lennert Buytenhek
Werner Almesberger
Rask Ingemann Lambertsen
Nicolas Ferre
Krzysztof Helt
Fenghua Yu
Alex Williamson
Ben Hutchings
Dave Jones
Wey-Yi Guy
Bing Zhao
Bob Copeland
Felix Fietkau
Martin Fuzzey
Denis Turischev
Francisco Jerez
Alex Deucher
Atsushi Nemoto
David Woodhouse
Sebastian Siewior
Michael Krufky
Laurent Pinchart
Jonathan Cameron
Theodore Kilgore
Erik Andrén
Stefan Richter
Henrik Kurelid
Mike Isely
Devin Heitmueller
HIRANO Takahito
Hans de Goede
Seth Barry
Martin Samek
Patrick Boettcher
Crane Cai
Martin Michlmayr
Ron Mercer
Don Skidmore
Yi Zou
Finn Thain
Jiri Slaby
Sebastian Haas
Ajit Khaparde
Kenji Kaneshige
Sean Cross
jack wang
Anil Ravindranath
Wayne Boyer
Brian King
Sathya Perla
Magnus Damm
Len Brown
Vaibhav Verma
Rafał Miłecki
Gustavo Maciel Dias Vieira
Amit Kucheria
Julia Lawall
Bob Moore
Rakib Mullick