MacBookPro5,1 is not able to reboot unless reboot=pci is set.
This patch forces it through a DMI quirk specific to this
device.
Signed-off-by: Ozan Çağlayan <ozan@pardus.org.tr>
LKML-Reference: <1249403971-6543-1-git-send-email-ozan@pardus.org.tr>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
With CONFIG_STACK_PROTECTOR turned on, VMI doesn't boot with
more than one processor. The problem is with the gs value not
being initialized correctly when registering the secondary
processor for VMI's case.
The patch below initializes the gs value for the AP to
__KERNEL_STACK_CANARY. Without this the secondary processor
keeps on taking a GP on every gs access.
Signed-off-by: Alok N Kataria <akataria@vmware.com>
Cc: <stable@kernel.org> # for v2.6.30.x
LKML-Reference: <1249425262.18955.40.camel@ank32.eng.vmware.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86: Work around compilation warning in arch/x86/kernel/apm_32.c
x86, UV: Complete IRQ interrupt migration in arch_enable_uv_irq()
x86, 32-bit: Fix double accounting in reserve_top_address()
x86: Don't use current_cpu_data in x2apic phys_pkg_id
x86, UV: Fix UV apic mode
x86, UV: Fix macros for accessing large node numbers
x86, UV: Delete mapping of MMR rangs mapped by BIOS
x86, UV: Handle missing blade-local memory correctly
x86: fix assembly constraints in native_save_fl()
x86, msr: execute on the correct CPU subset
x86: Fix assert syntax in vmlinux.lds.S
x86: Make 64-bit efi_ioremap use ioremap on MMIO regions
x86: Add quirk to make Apple MacBook5,2 use reboot=pci
x86: Fix CPA memtype reserving in the set_pages_array*() cases
x86, pat: Fix set_memory_wc related corruption
x86: fix section mismatch for i386 init code
The following fix was initially inspired by David Howells fix
few days back:
http://lkml.org/lkml/2009/7/9/109
However, Ingo disapproves such fixes as it's dangerous (it can
hide future, relevant warnings) - in something as
performance-uncritical.
So, initialize 'err' to '0' to work around a GCC false positive
warning:
http://lkml.org/lkml/2009/7/18/89
Signed-off-by: Subrata Modak<subrata@linux.vnet.ibm.com>
Cc: Sachin P Sant <sachinp@linux.vnet.ibm.com>
Cc: David Howells <dhowells@redhat.com>
Cc: Balbir Singh <balbir@linux.vnet.ibm.com>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
LKML-Reference: <20090721023226.31855.67236.sendpatchset@subratamodak.linux.ibm.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
In uv_setup_irq(), the call to create_irq() initially assigns
IRQ vectors to cpu 0. The subsequent call to
assign_irq_vector() in arch_enable_uv_irq() migrates the IRQ to
another cpu and frees the cpu 0 vector - at least it will be
freed as soon as the "IRQ move" completes.
arch_enable_uv_irq() needs to send a cleanup IPI to complete
the IRQ move. Otherwise, assignment of GRU interrupts on large
systems (>200 cpus) will exhaust the cpu 0 interrupt vectors
and initialization of the GRU driver will fail.
Signed-off-by: Jack Steiner <steiner@sgi.com>
LKML-Reference: <20090720142840.GA8885@sgi.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
With VMALLOC_END included in the calculation of MAXMEM (as of
2.6.28) it is no longer correct to also bump __VMALLOC_RESERVE
in reserve_top_address(). Doing so results in needlessly small
lowmem.
Signed-off-by: Jan Beulich <jbeulich@novell.com>
LKML-Reference: <4A71DD2A020000780000D482@vpn.id2.novell.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Change SGI UV default apicid mode to "physical". This is
required to match settings in the UV hub chip.
Signed-off-by: Jack Steiner <steiner@sgi.com>
LKML-Reference: <20090727143856.GA8905@sgi.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
The UV chipset automatically supplies the upper bits on nodes
being referenced by MMR accesses. These bit can be deleted from
the hub addressing macros.
Signed-off-by: Jack Steiner <steiner@sgi.com>
LKML-Reference: <20090727143808.GA8076@sgi.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
The UV BIOS has added additional MMR ranges that are mapped via
EFI virtual mode mappings. These ranges should be deleted from
ranges mapped by uv_system_init().
Signed-off-by: Jack Steiner <steiner@sgi.com>
Cc: linux-mm@kvack.org
LKML-Reference: <20090727143656.GA7698@sgi.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
UV blades may not have any blade-local memory. Add a field
(nid) to the UV blade structure to indicates whether the node
has local memory. This is needed by the GRU driver (pushed
separately).
Signed-off-by: Jack Steiner <steiner@sgi.com>
Cc: linux-mm@kvack.org
LKML-Reference: <20090727143507.GA7006@sgi.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
From Gabe Black in bugzilla 13888:
native_save_fl is implemented as follows:
11static inline unsigned long native_save_fl(void)
12{
13 unsigned long flags;
14
15 asm volatile("# __raw_save_flags\n\t"
16 "pushf ; pop %0"
17 : "=g" (flags)
18 : /* no input */
19 : "memory");
20
21 return flags;
22}
If gcc chooses to put flags on the stack, for instance because this is
inlined into a larger function with more register pressure, the offset
of the flags variable from the stack pointer will change when the
pushf is performed. gcc doesn't attempt to understand that fact, and
address used for pop will still be the same. It will write to
somewhere near flags on the stack but not actually into it and
overwrite some other value.
I saw this happen in the ide_device_add_all function when running in a
simulator I work on. I'm assuming that some quirk of how the simulated
hardware is set up caused the code path this is on to be executed when
it normally wouldn't.
A simple fix might be to change "=g" to "=r".
Reported-by: Gabe Black <spamforgabe@umich.edu>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Cc: Stable Team <stable@kernel.org>
Make rdmsr_on_cpus/wrmsr_on_cpus execute on the current CPU only if it
is in the supplied bitmask.
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Older versions of binutils did not accept the naked "ASSERT" syntax;
it is considered an expression whose value needs to be assigned to
something.
Reported-tested-and-fixed-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
The latest Apple MacBook (MacBook5,2) doesn't reboot successfully
under Linux; neither the EFI reboot method nor the default method
using the keyboard controller works (the system just hangs and doesn't
reset). However, the method using the "PCI reset register" at 0xcf9
does work.
This adds a quirk to detect this machine via DMI and force the
reboot_type to BOOT_CF9. With this it reboots successfully without
requiring a command-line option. Note that the EFI code forces
reboot_type to BOOT_EFI when the machine is booted via EFI, but this
overrides that since the core_initcall runs after the EFI
initialization code.
Signed-off-by: Paul Mackerras <paulus@samba.org>
LKML-Reference: <19062.56420.501516.316181@cargo.ozlabs.ibm.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
The code was incorrectly reserving memtypes using the page
virtual address instead of the physical address. Furthermore,
the code was not ignoring highmem pages as it ought to.
( upstream does not pass in highmem pages yet - but upcoming
graphics code will do it and there's no reason to not handle
this properly in the CPA APIs.)
Fixes: http://bugzilla.kernel.org/show_bug.cgi?id=13884
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Acked-by: Suresh Siddha <suresh.b.siddha@intel.com>
Cc: <stable@kernel.org>
Cc: dri-devel@lists.sourceforge.net
Cc: venkatesh.pallipadi@intel.com
LKML-Reference: <1249284345-7654-1-git-send-email-thellstrom@vmware.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Changeset 3869c4aa18
that went in after 2.6.30-rc1 was a seemingly small change to _set_memory_wc()
to make it complaint with SDM requirements. But, introduced a nasty bug, which
can result in crash and/or strange corruptions when set_memory_wc is used.
One such crash reported here
http://lkml.org/lkml/2009/7/30/94
Actually, that changeset introduced two bugs.
* change_page_attr_set() takes &addr as first argument and can the addr value
might have changed on return, even for single page change_page_attr_set()
call. That will make the second change_page_attr_set() in this routine
operate on unrelated addr, that can eventually cause strange corruptions
and bad page state crash.
* The second change_page_attr_set() call, before setting _PAGE_CACHE_WC, should
clear the earlier _PAGE_CACHE_UC_MINUS, as otherwise cache attribute will not
be WC (will be UC instead).
The patch below fixes both these problems. Sending a single patch to fix both
the problems, as the change is to the same line of code. The change to have a
addr_copy is not very clean. But, it is simpler than making more changes
through various routines in pageattr.c.
A huge thanks to Jerome for reporting this problem and providing a simple test
case that helped us root cause the problem.
Reported-by: Jerome Glisse <glisse@freedesktop.org>
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
LKML-Reference: <20090730214319.GA1889@linux-os.sc.intel.com>
Acked-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Every so often, after code shuffles, I need to go through and unbitrot
the Lguest Journey (see drivers/lguest/README). Since we now use RCU in
a simple form in one place I took the opportunity to expand that explanation.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Paul McKenney <paulmck@linux.vnet.ibm.com>
I don't really notice it (except to begrudge the extra vertical
space), but Ingo does. And he pointed out that one excuse of lguest
is as a teaching tool, it should set a good example.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Cc: Ingo Molnar <mingo@redhat.com>
* 'drm-radeon-kms' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6: (35 commits)
drm/radeon: set fb aperture sizes for framebuffer handoff.
drm/ttm: fix highuser vs dma32 confusion.
drm/radeon: Fix size used for benchmarking BO copies.
drm/radeon: Add radeon.test parameter for running BO GPU copy tests.
drm/radeon/kms: allow interruptible waits for objects.
drm/ttm: powerpc: Fix Highmem cache flushing.
x86: Export kmap_atomic_prot() needed for TTM.
drm/ttm: Fix ttm in-kernel copying of pages with non-standard caching attributes.
drm/ttm: Fix an oops and sync object leak.
drm/radeon/kms: vram sizing on certain r100 chips needs workaround.
drm/radeon: Pay more attention to object placement requested by userspace.
drm/radeon: Fall back to evicting BOs with memcpy if necessary.
drm/radeon: Don't unreserve twice on failure to validate.
drm/radeon/kms: fix bandwidth computation on avivo hardware
drm/radeon/kms: add initial colortiling support.
drm/radeon/kms: fix hotspot handling on pre-avivo chips
drm/radeon/kms: enable frac fb divs on rs600/rs690/rs740
drm/radeon/kms: add PLL flag to prefer frequencies <= the target freq
drm/radeon/kms: block RN50 from using 3D engine.
drm/radeon/kms: fix VRAM sizing like DDX does it.
...
This functionality is needed to kmap_atomic() highmem pages that may
potentially have or are about to set up other mappings with
non-standard caching attributes.
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Startup code for i386 in arch/x86/kernel/head_32.S is using the
reference variable initial_code that is located in the .cpuinit.data
section. If CONFIG_HOTPLUG_CPU is enabled, startup code is not in an
init section and can be called later too. In this case the reference
initial_code must be kept too. This patch fixes this. See below for
the section mismatch warning.
WARNING: vmlinux.o(.cpuinit.data+0x0): Section mismatch in reference
from the variable initial_code to the function
.init.text:i386_start_kernel()
The variable __cpuinitdata initial_code references
a function __init i386_start_kernel().
If i386_start_kernel is only used by initial_code then
annotate i386_start_kernel with a matching annotation.
Signed-off-by: Robert Richter <robert.richter@amd.com>
LKML-Reference: <1248716632-26844-1-git-send-email-robert.richter@amd.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86: geode: Mark mfgpt irq IRQF_TIMER to prevent resume failure
x86, amd: Don't probe for extended APIC ID if APICs are disabled
x86, mce: Rename incorrect macro name "CONFIG_X86_THRESHOLD"
x86-64: Fix bad_srat() to clear all state
x86, mce: Fix set_trigger() accessor
x86: Fix movq immediate operand constraints in uaccess.h
x86: Fix movq immediate operand constraints in uaccess_64.h
x86: Add reboot fixup for SBC-fitPC2
x86: Include all of .data.* sections in _edata on 64-bit
x86: Add quirk for Intel DG45ID board to avoid low memory corruption
mm: Pass virtual address to [__]p{te,ud,md}_free_tlb()
Upcoming paches to support the new 64-bit "BookE" powerpc architecture
will need to have the virtual address corresponding to PTE page when
freeing it, due to the way the HW table walker works.
Basically, the TLB can be loaded with "large" pages that cover the whole
virtual space (well, sort-of, half of it actually) represented by a PTE
page, and which contain an "indirect" bit indicating that this TLB entry
RPN points to an array of PTEs from which the TLB can then create direct
entries. Thus, in order to invalidate those when PTE pages are deleted,
we need the virtual address to pass to tlbilx or tlbivax instructions.
The old trick of sticking it somewhere in the PTE page struct page sucks
too much, the address is almost readily available in all call sites and
almost everybody implemets these as macros, so we may as well add the
argument everywhere. I added it to the pmd and pud variants for consistency.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: David Howells <dhowells@redhat.com> [MN10300 & FRV]
Acked-by: Nick Piggin <npiggin@suse.de>
Acked-by: Martin Schwidefsky <schwidefsky@de.ibm.com> [s390]
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Timer interrupts are excluded from being disabled during suspend. The
clock events code manages the disabling of clock events on its own
because the timer interrupt needs to be functional before the resume
code reenables the device interrupts.
The mfgpt timer request its interrupt without setting the IRQF_TIMER
flag so suspend_device_irqs() disables it as well which results in a
fatal resume failure.
Adding IRQF_TIMER to the interupt flags when requesting the mrgpt
timer interrupt solves the problem.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
LKML-Reference: <new-submission>
Cc: Andres Salomon <dilinger@debian.org>
Cc: stable@kernel.org
* 'perf-counters-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/peterz/linux-2.6-perf: (31 commits)
perf_counter tools: Give perf top inherit option
perf_counter tools: Fix vmlinux symbol generation breakage
perf_counter: Detect debugfs location
perf_counter: Add tracepoint support to perf list, perf stat
perf symbol: C++ demangling
perf: avoid structure size confusion by using a fixed size
perf_counter: Fix throttle/unthrottle event logging
perf_counter: Improve perf stat and perf record option parsing
perf_counter: PERF_SAMPLE_ID and inherited counters
perf_counter: Plug more stack leaks
perf: Fix stack data leak
perf_counter: Remove unused variables
perf_counter: Make call graph option consistent
perf_counter: Add perf record option to log addresses
perf_counter: Log vfork as a fork event
perf_counter: Synthesize VDSO mmap event
perf_counter: Make sure we dont leak kernel memory to userspace
perf_counter tools: Fix index boundary check
perf_counter: Fix the tracepoint channel to perfcounters
perf_counter, x86: Extend perf_counter Pentium M support
...
If we've logically disabled apics, don't probe the PCI space for the
AMD extended APIC ID.
[ Impact: prevent boot crash under Xen. ]
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Reported-by: Bastian Blank <bastian@waldi.eu.org>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
CONFIG_X86_THRESHOLD used in arch/x86/kernel/irqinit.c is always
undefined. Rename it to the correct name "CONFIG_X86_MCE_THRESHOLD".
Signed-off-by: Hidehiro Kawai <hidehiro.kawai.ez@hitachi.com>
Reviewed-by: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Cc: Andi Kleen <andi@firstfloor.org>
LKML-Reference: <4A667FD4.3010509@hitachi.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Need to clear both nodes and nodes_add state for start/end.
Signed-off-by: Andi Kleen <ak@linux.intel.com>
LKML-Reference: <20090718065657.GA2898@basil.fritz.box>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Cc: stable@kernel.org
Fix the condition checking the result of strchr() (which previously
could result in an oops), and make the function return the number of
bytes actively used.
[ Impact: fix oops ]
Signed-off-by: Jan Beulich <jbeulich@novell.com>
Cc: Andi Kleen <andi@firstfloor.org>
LKML-Reference: <4A5F04B7020000780000AB59@vpn.id2.novell.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
The movq instruction, generated by __put_user_asm() when used for
64-bit data, takes a sign-extended immediate ("e") not a zero-extended
immediate ("Z").
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Cc: Uros Bizjak <ubizjak@gmail.com>
Cc: stable@kernel.org
arch/x86/include/asm/uaccess_64.h uses wrong asm operand constraint
("ir") for movq insn. Since movq sign-extends its immediate operand,
"er" constraint should be used instead.
Attached patch changes all uses of __put_user_asm in uaccess_64.h to use
"er" when "q" insn suffix is involved.
Patch was compile tested on x86_64 with defconfig.
Signed-off-by: Uros Bizjak <ubizjak@gmail.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Cc: stable@kernel.org
The CompuLab SBC-fitPC2 board needs to reboot via BIOS.
Signed-off-by: Denis Turischev <denis@compulab.co.il>
Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
The .data.read_mostly and .data.cacheline_aligned sections
aren't covered by the _sdata .. _edata range on x86-64. This
affects kmemleak reporting leading to possible false
positives by not scanning the whole data section.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Tested-by: Alexey Fisher <bug-track@fisher-privat.net>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Cc: Pekka Enberg <penberg@cs.helsinki.fi>
LKML-Reference: <1247565175.28240.37.camel@pc1117.cambridge.arm.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Cc: Sam Ravnborg <sam@ravnborg.org>
AMI BIOS with low memory corruption was found on Intel DG45ID
board (Bug 13710). Add this board to the blacklist - in the
(somewhat optimistic) hope of future boards/BIOSes from Intel
not having this bug.
Also see:
http://bugzilla.kernel.org/show_bug.cgi?id=13736
Signed-off-by: Alexey Fisher <bug-track@fisher-privat.net>
Cc: ykzhao <yakui.zhao@intel.com>
Cc: alan@lxorguk.ukuu.org.uk
Cc: <stable@kernel.org>
LKML-Reference: <1247660169-4503-1-git-send-email-bug-track@fisher-privat.net>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Avoid the following:
[ 0.012093] WARNING: at arch/x86/kernel/apic/apic.c:249 native_apic_write_dummy+0x2f/0x40()
Rather than chase each new cpuid-detected feature, just lie about the highest
valid CPUID so this code is never run.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
when building 32-bit, I see this ..
arch/x86/kernel/pvclock.c:63:7: warning: "__x86_64__" is not defined
Signed-off-by: Dave Jones <davej@redhat.com>
LKML-Reference: <20090713201437.GA12165@redhat.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The variable apic_numaq placed in noninit section references the
function wakeup_secondary_cpu_via_nmi(), which is in __cpuinit
section. Thus causes a section mismatch warning. To avoid such
mismatch we mark apic_numaq as __refdata.
We were warned by the following warning:
WARNING: arch/x86/kernel/built-in.o(.data+0x932c): Section mismatch in
reference from the variable apic_numaq to the function
.cpuinit.text:wakeup_secondary_cpu_via_nmi()
Signed-off-by: Rakib Mullick <rakib.mullick@gmail.com>
LKML-Reference: <b9df5fa10907120407p6b4f67dtf4d563155488188a@mail.gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
The variable apic_es7000_cluster references the function __cpuinit
wakeup_secondary_cpu_via_mip() from a noninit section. So we've been
warned by the following warning. To avoid possible collision between
init/noninit, its best to mark the variable as __refdata.
We were warned by the following warning:
LD arch/x86/kernel/apic/built-in.o
WARNING: arch/x86/kernel/apic/built-in.o(.data+0x198c): Section
mismatch in reference from the variable apic_es7000_cluster to the
function .cpuinit.text:wakeup_secondary_cpu_via_mip()
Signed-off-by: Rakib Mullick <rakib.mullick@gmail.com>
LKML-Reference: <b9df5fa10907120404k6279a10ch5e9682432272706f@mail.gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
I've attached a patch to remove the Pentium M special casing of
EMON and as noticed at least with my Pentium M the hardware PMU
now works:
Performance counter stats for '/bin/ls /var/tmp':
1.809988 task-clock-msecs # 0.125 CPUs
1 context-switches # 0.001 M/sec
0 CPU-migrations # 0.000 M/sec
224 page-faults # 0.124 M/sec
1425648 cycles # 787.656 M/sec
912755 instructions # 0.640 IPC
Vince suggested that this code was trying to address erratum
Y17 in Pentium-M's:
http://download.intel.com/support/processors/mobile/pm/sb/25266532.pdf
But that erratum (related to IA32_MISC_ENABLES.7) does not
affect perfcounters as we dont use this toggle to disable RDPMC
and WRMSR/RDMSR access to performance counters. We keep cr4's
bit 8 (X86_CR4_PCE) clear so unprivileged RDPMC access is not
allowed anyway.
Cc: Vince Weaver <vince@deater.net>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Stephane Eranian <eranian@googlemail.com>
LKML-Reference: <new-submission>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Since commit 5fd29d6c ("printk: clean up handling of log-levels
and newlines"), the kernel logs segfaults like:
<6>gnome-power-man[24509]: segfault at 20 ip 00007f9d4950465a sp 00007fffbb50fc70 error 4 in libgobject-2.0.so.0.2103.0[7f9d494f7000+45000]
with the extra "<6>" being KERN_INFO. This happens because the
printk in show_signal_msg() started with KERN_CONT and then
used "%s" to pass in the real level; and KERN_CONT is no longer
an empty string, and printk only pays attention to the level at
the very beginning of the format string.
Therefore, remove the KERN_CONT from this printk, since it is
now actively causing problems (and never really made any
sense).
Signed-off-by: Roland Dreier <roland@digitalvampire.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
LKML-Reference: <874otjitkj.fsf@shaolin.home.digitalvampire.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
* 'core-fixes-for-linus-2' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
dma-debug: Fix the overlap() function to be correct and readable
oprofile: reset bt_lost_no_mapping with other stats
x86/oprofile: rename kernel parameter for architectural perfmon to arch_perfmon
signals: declare sys_rt_tgsigqueueinfo in syscalls.h
rcu: Mark Hierarchical RCU no longer experimental
dma-debug: Put all hash-chain locks into the same lock class
dma-debug: fix off-by-one error in overlap function
* 'perfcounters-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (50 commits)
perf report: Add "Fractal" mode output - support callchains with relative overhead rate
perf_counter tools: callchains: Manage the cumul hits on the fly
perf report: Change default callchain parameters
perf report: Use a modifiable string for default callchain options
perf report: Warn on callchain output request from non-callchain file
x86: atomic64: Inline atomic64_read() again
x86: atomic64: Clean up atomic64_sub_and_test() and atomic64_add_negative()
x86: atomic64: Improve atomic64_xchg()
x86: atomic64: Export APIs to modules
x86: atomic64: Improve atomic64_read()
x86: atomic64: Code atomic(64)_read and atomic(64)_set in C not CPP
x86: atomic64: Fix unclean type use in atomic64_xchg()
x86: atomic64: Make atomic_read() type-safe
x86: atomic64: Reduce size of functions
x86: atomic64: Improve atomic64_add_return()
x86: atomic64: Improve cmpxchg8b()
x86: atomic64: Improve atomic64_read()
x86: atomic64: Move the 32-bit atomic64_t implementation to a .c file
x86: atomic64: The atomic64_t data type should be 8 bytes aligned on 32-bit too
perf report: Annotate variable initialization
...
Pull the initial preempt_count value into a single
definition site.
Maintainers for: alpha, ia64 and m68k, please have a look,
your arch code is funny.
The header magic is a bit odd, but similar to the KERNEL_DS
one, CPP waits with expanding these macros until the
INIT_THREAD_INFO macro itself is expanded, which is in
arch/*/kernel/init_task.c where we've already included
sched.h so we're good.
Cc: tony.luck@intel.com
Cc: rth@twiddle.net
Cc: geert@linux-m68k.org
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Acked-by: Matt Mackall <mpm@selenic.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Ozan Çağlayan
Yinghai Lu
Alok Kataria
Linus Torvalds
Subrata Modak
Jack Steiner
Jan Beulich
H. Peter Anvin
Borislav Petkov
Paul Mackerras
Thomas Hellstrom
Pallipadi, Venkatesh
Rusty Russell
Robert Richter
Benjamin Herrenschmidt
Thomas Gleixner
Jeremy Fitzhardinge
Peter Zijlstra
Hidehiro Kawai
Andi Kleen
Uros Bizjak
Denis Turischev
Catalin Marinas
Alexey Fisher
Matias Zabaljauregui
Dave Jones
Rakib Mullick
Daniel Qarras
Roland Dreier