Commit 2e9f60932a ("net: hsr: check skb can contain struct hsr_ethhdr
in fill_frame_info") added the following which resulted in -EINVAL
always being returned:
if (skb->mac_len < sizeof(struct hsr_ethhdr))
return -EINVAL;
mac_len was not being set correctly so this check completely broke
HSR/PRP since it was always 14, not 20.
Set mac_len correctly and modify the mac_len checks to test in the
correct places since sometimes it is legitimately 14.
Fixes: 2e9f60932a ("net: hsr: check skb can contain struct hsr_ethhdr in fill_frame_info")
Signed-off-by: George McCollister <george.mccollister@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for offloading of HSR/PRP (IEC 62439-3) tag insertion
tag removal, duplicate generation and forwarding.
For HSR, insertion involves the switch adding a 6 byte HSR header after
the 14 byte Ethernet header. For PRP it adds a 6 byte trailer.
Tag removal involves automatically stripping the HSR/PRP header/trailer
in the switch. This is possible when the switch also performs auto
deduplication using the HSR/PRP header/trailer (making it no longer
required).
Forwarding involves automatically forwarding between redundant ports in
an HSR. This is crucial because delay is accumulated as a frame passes
through each node in the ring.
Duplication involves the switch automatically sending a single frame
from the CPU port to both redundant ports. This is required because the
inserted HSR/PRP header/trailer must contain the same sequence number
on the frames sent out both redundant ports.
Export is_hsr_master so DSA can tell them apart from other devices in
dsa_slave_changeupper.
Signed-off-by: George McCollister <george.mccollister@gmail.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
DAN-P (Dual Attached Nodes PRP) nodes are expected to receive
traditional IP packets as well as PRP (Parallel Redundancy
Protocol) tagged (trailer) packets. PRP trailer is 6 bytes
of PRP protocol unit called RCT, Redundancy Control Trailer
(RCT) similar to HSR tag. PRP network can have traditional
devices such as bridges/switches or PC attached to it and
should be able to communicate. Regular Ethernet devices treat
the RCT as pads. This patch adds logic to format L2 frames
from network stack to add a trailer (RCT) and send it as
duplicates over the slave interfaces when the protocol is
PRP as per IEC 62439-3. At the ingress, it strips the trailer,
do duplicate detection and rejection and forward a stripped
frame up the network stack. PRP device should accept frames
from Singly Attached Nodes (SAN) and thus the driver mark
the link where the frame came from in the node table.
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Parallel Redundancy Protocol (PRP) is another redundancy protocol
introduced by IEC 63439 standard. It is similar to HSR in many
aspects:-
- Use a pair of Ethernet interfaces to created the PRP device
- Use a 6 byte redundancy protocol part (RCT, Redundancy Check
Trailer) similar to HSR Tag.
- Has Link Redundancy Entity (LRE) that works with RCT to implement
redundancy.
Key difference is that the protocol unit is a trailer instead of a
prefix as in HSR. That makes it inter-operable with tradition network
components such as bridges/switches which treat it as pad bytes,
whereas HSR nodes requires some kind of translators (Called redbox) to
talk to regular network devices. This features allows regular linux box
to be converted to a DAN-P box. DAN-P stands for Dual Attached Node - PRP
similar to DAN-H (Dual Attached Node - HSR).
Add a comment at the header/source code to explicitly state that the
driver files also handles PRP protocol as well.
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix following sparse checker warning:-
net/hsr/hsr_slave.c:38:18: warning: incorrect type in assignment (different base types)
net/hsr/hsr_slave.c:38:18: expected unsigned short [unsigned] [usertype] protocol
net/hsr/hsr_slave.c:38:18: got restricted __be16 [usertype] h_proto
net/hsr/hsr_slave.c:39:25: warning: restricted __be16 degrades to integer
net/hsr/hsr_slave.c:39:57: warning: restricted __be16 degrades to integer
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Acked-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Overlapping header include additions in macsec.c
A bug fix in 'net' overlapping with the removal of 'version'
string in ena_netdev.c
Overlapping test additions in selftests Makefile
Overlapping PCI ID table adjustments in iwlwifi driver.
Signed-off-by: David S. Miller <davem@davemloft.net>
The port->hsr is used in the hsr_handle_frame(), which is a
callback of rx_handler.
hsr master and slaves are initialized in hsr_add_port().
This function initializes several pointers, which includes port->hsr after
registering rx_handler.
So, in the rx_handler routine, un-initialized pointer would be used.
In order to fix this, pointers should be initialized before
registering rx_handler.
Test commands:
ip netns del left
ip netns del right
modprobe -rv veth
modprobe -rv hsr
killall ping
modprobe hsr
ip netns add left
ip netns add right
ip link add veth0 type veth peer name veth1
ip link add veth2 type veth peer name veth3
ip link add veth4 type veth peer name veth5
ip link set veth1 netns left
ip link set veth3 netns right
ip link set veth4 netns left
ip link set veth5 netns right
ip link set veth0 up
ip link set veth2 up
ip link set veth0 address fc:00:00:00:00:01
ip link set veth2 address fc:00:00:00:00:02
ip netns exec left ip link set veth1 up
ip netns exec left ip link set veth4 up
ip netns exec right ip link set veth3 up
ip netns exec right ip link set veth5 up
ip link add hsr0 type hsr slave1 veth0 slave2 veth2
ip a a 192.168.100.1/24 dev hsr0
ip link set hsr0 up
ip netns exec left ip link add hsr1 type hsr slave1 veth1 slave2 veth4
ip netns exec left ip a a 192.168.100.2/24 dev hsr1
ip netns exec left ip link set hsr1 up
ip netns exec left ip n a 192.168.100.1 dev hsr1 lladdr \
fc:00:00:00:00:01 nud permanent
ip netns exec left ip n r 192.168.100.1 dev hsr1 lladdr \
fc:00:00:00:00:01 nud permanent
for i in {1..100}
do
ip netns exec left ping 192.168.100.1 &
done
ip netns exec left hping3 192.168.100.1 -2 --flood &
ip netns exec right ip link add hsr2 type hsr slave1 veth3 slave2 veth5
ip netns exec right ip a a 192.168.100.3/24 dev hsr2
ip netns exec right ip link set hsr2 up
ip netns exec right ip n a 192.168.100.1 dev hsr2 lladdr \
fc:00:00:00:00:02 nud permanent
ip netns exec right ip n r 192.168.100.1 dev hsr2 lladdr \
fc:00:00:00:00:02 nud permanent
for i in {1..100}
do
ip netns exec right ping 192.168.100.1 &
done
ip netns exec right hping3 192.168.100.1 -2 --flood &
while :
do
ip link add hsr0 type hsr slave1 veth0 slave2 veth2
ip a a 192.168.100.1/24 dev hsr0
ip link set hsr0 up
ip link del hsr0
done
Splat looks like:
[ 120.954938][ C0] general protection fault, probably for non-canonical address 0xdffffc0000000006: 0000 [#1]I
[ 120.957761][ C0] KASAN: null-ptr-deref in range [0x0000000000000030-0x0000000000000037]
[ 120.959064][ C0] CPU: 0 PID: 1511 Comm: hping3 Not tainted 5.6.0-rc5+ #460
[ 120.960054][ C0] Hardware name: innotek GmbH VirtualBox/VirtualBox, BIOS VirtualBox 12/01/2006
[ 120.962261][ C0] RIP: 0010:hsr_addr_is_self+0x65/0x2a0 [hsr]
[ 120.963149][ C0] Code: 44 24 18 70 73 2f c0 48 c1 eb 03 48 8d 04 13 c7 00 f1 f1 f1 f1 c7 40 04 00 f2 f2 f2 4
[ 120.966277][ C0] RSP: 0018:ffff8880d9c09af0 EFLAGS: 00010206
[ 120.967293][ C0] RAX: 0000000000000006 RBX: 1ffff1101b38135f RCX: 0000000000000000
[ 120.968516][ C0] RDX: dffffc0000000000 RSI: ffff8880d17cb208 RDI: 0000000000000000
[ 120.969718][ C0] RBP: 0000000000000030 R08: ffffed101b3c0e3c R09: 0000000000000001
[ 120.972203][ C0] R10: 0000000000000001 R11: ffffed101b3c0e3b R12: 0000000000000000
[ 120.973379][ C0] R13: ffff8880aaf80100 R14: ffff8880aaf800f2 R15: ffff8880aaf80040
[ 120.974410][ C0] FS: 00007f58e693f740(0000) GS:ffff8880d9c00000(0000) knlGS:0000000000000000
[ 120.979794][ C0] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 120.980773][ C0] CR2: 00007ffcb8b38f29 CR3: 00000000afe8e001 CR4: 00000000000606f0
[ 120.981945][ C0] Call Trace:
[ 120.982411][ C0] <IRQ>
[ 120.982848][ C0] ? hsr_add_node+0x8c0/0x8c0 [hsr]
[ 120.983522][ C0] ? rcu_read_lock_held+0x90/0xa0
[ 120.984159][ C0] ? rcu_read_lock_sched_held+0xc0/0xc0
[ 120.984944][ C0] hsr_handle_frame+0x1db/0x4e0 [hsr]
[ 120.985597][ C0] ? hsr_nl_nodedown+0x2b0/0x2b0 [hsr]
[ 120.986289][ C0] __netif_receive_skb_core+0x6bf/0x3170
[ 120.992513][ C0] ? check_chain_key+0x236/0x5d0
[ 120.993223][ C0] ? do_xdp_generic+0x1460/0x1460
[ 120.993875][ C0] ? register_lock_class+0x14d0/0x14d0
[ 120.994609][ C0] ? __netif_receive_skb_one_core+0x8d/0x160
[ 120.995377][ C0] __netif_receive_skb_one_core+0x8d/0x160
[ 120.996204][ C0] ? __netif_receive_skb_core+0x3170/0x3170
[ ... ]
Reported-by: syzbot+fcf5dd39282ceb27108d@syzkaller.appspotmail.com
Fixes: c5a7591172 ("net/hsr: Use list_head (and rcu) instead of array for slave devices.")
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the commit e0a4b99773 ("hsr: use upper/lower device infrastructure"),
dev_get() was removed but dev_put() in the error path wasn't removed.
So, if creating hsr interface command is failed, the reference counter leak
of lower interface would occur.
Test commands:
ip link add dummy0 type dummy
ip link add ipvlan0 link dummy0 type ipvlan mode l2
ip link add ipvlan1 link dummy0 type ipvlan mode l2
ip link add hsr0 type hsr slave1 ipvlan0 slave2 ipvlan1
ip link del ipvlan0
Result:
[ 633.271992][ T1280] unregister_netdevice: waiting for ipvlan0 to become free. Usage count = -1
Fixes: e0a4b99773 ("hsr: use upper/lower device infrastructure")
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
netdev_upper_dev_link() is useful to manage lower/upper interfaces.
And this function internally validates looping, maximum depth.
All or most virtual interfaces that could have a real interface
(e.g. macsec, macvlan, ipvlan etc.) use lower/upper infrastructure.
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to access the port list, the hsr_port_get_hsr() is used.
And this is protected by RTNL and RCU.
The hsr_fill_info(), hsr_check_carrier(), hsr_dev_open() and
hsr_get_max_mtu() are protected by RTNL.
So, rcu_read_lock() in these functions are not necessary.
The hsr_handle_frame() also uses rcu_read_lock() but this function
is called by packet path.
It's already protected by RCU.
So, the rcu_read_lock() in hsr_handle_frame() can be removed.
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If HSR uses the extack instead of netdev_info(), users can get
error messages immediately without any checking the kernel message.
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
hsr_del_port() should release all the resources allocated
in hsr_add_port().
As a consequence of this change, hsr_for_each_port() is no
longer safe to work with hsr_del_port(), switch to
list_for_each_entry_safe() as we always hold RTNL lock.
Cc: Arvid Brodin <arvid.brodin@alten.se>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use SPDX-License-Identifier instead of a verbose license text.
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch replaces all instance of NULL checks such as
if (foo == NULL) with if (!foo)
Also
if (foo != NULL) with if (foo)
This is seen when ran checkpatch.pl -f on files under net/hsr
and suggestion is to replace as above.
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes unnecessary paranthesis from the code. This is
seen when ran checkpatch.pl -f option on files under net/hsr.
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes multiple blank lines in the code. This is seen
when ran checkpatch.pl -f option for files under net/hsr
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch makes use of is_vlan_dev() function instead of flag
comparison which is exactly done by is_vlan_dev() helper function.
Signed-off-by: Parav Pandit <parav@mellanox.com>
Reviewed-by: Daniel Jurgens <danielj@mellanox.com>
Acked-by: Stephen Hemminger <stephen@networkplumber.org>
Acked-by: Jon Maxwell <jmaxwell37@gmail.com>
Acked-by: Johannes Thumshirn <jth@kernel.org>
Acked-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for the newer version 1 of the HSR
networking standard. Version 0 is still default and the new
version has to be selected via iproute2.
Main changes are in the supervision frame handling and its
ethertype field.
Signed-off-by: Peter Heise <peter.heise@airbus.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To repeat:
$ sudo ip link del hsr0
BUG: unable to handle kernel NULL pointer dereference at 0000000000000018
IP: [<ffffffff8187f495>] hsr_del_port+0x15/0xa0
etc...
Bug description:
As part of the hsr master device destruction, hsr_del_port() is called for each of
the hsr ports. At each such call, the master device is updated regarding features
and mtu. When the master device is freed before the slave interfaces, master will
be NULL in hsr_del_port(), which led to a NULL pointer dereference.
Additionally, dev_put() was called on the master device itself in hsr_del_port(),
causing a refcnt error.
A third bug in the same code path was that the rtnl lock was not taken before
hsr_del_port() was called as part of hsr_dev_destroy().
The reporter (Nicolas Dichtel) also said: "hsr_netdev_notify() supposes that the
port will always be available when the notification is for an hsr interface. It's
wrong. For example, netdev_wait_allrefs() may resend NETDEV_UNREGISTER.". As a
precaution against this, a check for port == NULL was added in hsr_dev_notify().
Reported-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Fixes: 51f3c60531 ("net/hsr: Move slave init to hsr_slave.c.")
Signed-off-by: Arvid Brodin <arvid.brodin@alten.se>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch removes the separate paths for frames coming from the outside, and
frames sent from the HSR device, and instead makes all frames go through
hsr_forward_skb() in hsr_forward.c. This greatly improves code readability and
also opens up the possibility for future support of the HSR Interlink device
that is the basis for HSR RedBoxes and HSR QuadBoxes, as well as VLAN
compatibility.
Other improvements:
* A reduction in the number of times an skb is copied on machines without
HAVE_EFFICIENT_UNALIGNED_ACCESS, which improves throughput somewhat.
* Headers are now created using the standard eth_header(), and using the
standard hard_header_len.
* Each HSR slave now gets its own private skb, so slave-specific fields can be
correctly set.
Signed-off-by: Arvid Brodin <arvid.brodin@alten.se>
Signed-off-by: David S. Miller <davem@davemloft.net>
Also try to prevent some possible slave dereference race conditions. This is
finalized in the next patch, which abandons the slave array in favour of
a list_head list and list RCU.
Signed-off-by: Arvid Brodin <arvid.brodin@alten.se>
Signed-off-by: David S. Miller <davem@davemloft.net>
Also move the frame receive handler to hsr_slave.c.
Signed-off-by: Arvid Brodin <arvid.brodin@alten.se>
Signed-off-by: David S. Miller <davem@davemloft.net>
George McCollister
Murali Karicheri
David S. Miller
Taehee Yoo
Eric Dumazet
Cong Wang
Parav Pandit
Peter Heise
Arvid Brodin