n_gsm is based on the 3GPP 07.010 and its newer version is the 3GPP 27.010.
See https://portal.3gpp.org/desktopmodules/Specifications/SpecificationDetails.aspx?specificationId=1516
The changes from 07.010 to 27.010 are non-functional. Therefore, I refer to
the newer 27.010 here. Chapters 5.4.6.3.4 and 5.1.8.1.3 describe the test
command which can be used to test the mux connection between both sides.
Currently, no algorithm is implemented to make use of this command. This
requires that each multiplexed upper layer protocol supervises the
underlying muxer connection to handle possible connection losses.
Introduce ioctl commands and functions to optionally enable keep alive
handling via the test command as described in chapter 5.4.6.3.4. A single
incrementing octet "ka_num" is being used for unique identification of each
single keep alive packet. Retries will use the same "ka_num" value as the
original packet. Retry count and interval are taken from the general
parameters N2 and T2.
Add usage description and basic example for the new ioctl to the n_gsm
documentation.
Note that support for the test command is mandatory and already present in
the muxer implementation since the very first version.
Also note that the previous ioctl structure gsm_config cannot be extended
due to missing checks against zero of the field "unused".
Signed-off-by: Daniel Starke <daniel.starke@siemens.com>
Link: https://lore.kernel.org/r/20230214122737.1976-1-daniel.starke@siemens.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add support for the TIOCMIWAIT ioctl on the virtual ttys. This enables the
user to wait for virtual modem signals like RING.
More work is needed to support also TIOCGICOUNT.
Signed-off-by: Daniel Starke <daniel.starke@siemens.com>
Link: https://lore.kernel.org/r/20230206114606.2133-4-daniel.starke@siemens.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The status lines ring and carrier detect are used by the modem to signal
incoming calls (RING) or an established connection (CD). This is
implemented as physical lines on a standard RS232 connection. However,
the muxer protocol encodes these status lines as modem bits IC and DV.
These incoming lines are masked by tty driver (see tty_io.c) and cannot be
set by a user application.
Allow setting RING via TIOCM_OUT1 and CD via TIOCM_OUT2 to allow
implementation of a modem or modem emulator.
Signed-off-by: Daniel Starke <daniel.starke@siemens.com>
Link: https://lore.kernel.org/r/20230206114606.2133-3-daniel.starke@siemens.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Convert various parameter names for ->dtr_rts() and related functions
from onoff, on, and raise to active.
Reviewed-by: Jiri Slaby <jirislaby@kernel.org>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org> # For MMC
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20230117090358.4796-12-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Convert the raise/on parameter in ->dtr_rts() to bool through the
callchain. The parameter is used like bool. In USB serial, there
remains a few implicit bool -> larger type conversions because some
devices use u8 in their control messages.
In moxa_tiocmget(), dtr variable was reused for line status which
requires int so use a separate variable for status.
Reviewed-by: Jiri Slaby <jirislaby@kernel.org>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org> # For MMC
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20230117090358.4796-8-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Return boolean from ->carrier_raised() instead of 0 and 1. Make the
return type change also to tty_port_carrier_raised() that makes the
->carrier_raised() call (+ cd variable in moxa into which its return
value is stored).
Also cleans up a few unnecessary constructs related to this change:
return xx ? 1 : 0;
-> return xx;
if (xx)
return 1;
return 0;
-> return xx;
Reviewed-by: Jiri Slaby <jirislaby@kernel.org>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org> # For MMC
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20230117090358.4796-7-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Due to several bugs caused by timers being re-armed after they are
shutdown and just before they are freed, a new state of timers was added
called "shutdown". After a timer is set to this state, then it can no
longer be re-armed.
The following script was run to find all the trivial locations where
del_timer() or del_timer_sync() is called in the same function that the
object holding the timer is freed. It also ignores any locations where
the timer->function is modified between the del_timer*() and the free(),
as that is not considered a "trivial" case.
This was created by using a coccinelle script and the following
commands:
$ cat timer.cocci
@@
expression ptr, slab;
identifier timer, rfield;
@@
(
- del_timer(&ptr->timer);
+ timer_shutdown(&ptr->timer);
|
- del_timer_sync(&ptr->timer);
+ timer_shutdown_sync(&ptr->timer);
)
... when strict
when != ptr->timer
(
kfree_rcu(ptr, rfield);
|
kmem_cache_free(slab, ptr);
|
kfree(ptr);
)
$ spatch timer.cocci . > /tmp/t.patch
$ patch -p1 < /tmp/t.patch
Link: https://lore.kernel.org/lkml/20221123201306.823305113@linutronix.de/
Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>
Acked-by: Pavel Machek <pavel@ucw.cz> [ LED ]
Acked-by: Kalle Valo <kvalo@kernel.org> [ wireless ]
Acked-by: Paolo Abeni <pabeni@redhat.com> [ networking ]
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
n_gsm is based on the 3GPP 07.010 and its newer version is the 3GPP 27.010.
See https://portal.3gpp.org/desktopmodules/Specifications/SpecificationDetails.aspx?specificationId=1516
The changes from 07.010 to 27.010 are non-functional. Therefore, I refer to
the newer 27.010 here. Chapter 5.1.8.1.1 describes the parameter negotiation
messages and parameters. Chapter 5.4.1 states that the default parameters
are to be used if no negotiation is performed. Chapter 5.4.6.3.1 describes
the encoding of the parameter negotiation message. The meaning of the
parameters and allowed value ranges can be found in chapter 5.7.
Add parameter negotiation support accordingly. DLCI specific parameter
configuration by the user requires additional ioctls. This is subject to
another patch.
Signed-off-by: Daniel Starke <daniel.starke@siemens.com>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20221103091743.2119-3-daniel.starke@siemens.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
n_gsm is based on the 3GPP 07.010 and its newer version is the 3GPP 27.010.
See https://portal.3gpp.org/desktopmodules/Specifications/SpecificationDetails.aspx?specificationId=1516
The changes from 07.010 to 27.010 are non-functional. Therefore, I refer to
the newer 27.010 here. Chapter 5.4.6.3.1 describes the encoding of the
parameter negotiation messages.
Add the parameters used there to 'gsm_mux' and 'gsm_dlci' and initialize both
according to the value ranges and recommended defaults defined in chapter 5.7.
Replace the use of the DLC default values from the 'gsm_mux' fields with the DLC
specific values from the 'gsm_dlci' fields where applicable.
Signed-off-by: Daniel Starke <daniel.starke@siemens.com>
Link: https://lore.kernel.org/r/20221103091743.2119-2-daniel.starke@siemens.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
n_gsm has a minimal protocol overhead of 7 bytes. The current code already
checks whether the configured MRU/MTU size is at least one byte more than
this.
Introduce the macro MIN_MTU to make this value more obvious.
Signed-off-by: Daniel Starke <daniel.starke@siemens.com>
Link: https://lore.kernel.org/r/20221103091743.2119-1-daniel.starke@siemens.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The function gsm_dlci_t1() is a timer handler that runs in an
atomic context, but it calls "kzalloc(..., GFP_KERNEL)" that
may sleep. As a result, the sleep-in-atomic-context bug will
happen. The process is shown below:
gsm_dlci_t1()
gsm_dlci_open()
gsm_modem_update()
gsm_modem_upd_via_msc()
gsm_control_send()
kzalloc(sizeof(.., GFP_KERNEL) //may sleep
This patch changes the gfp_t parameter of kzalloc() from GFP_KERNEL to
GFP_ATOMIC in order to mitigate the bug.
Fixes: e1eaea46bb ("tty: n_gsm line discipline")
Signed-off-by: Duoming Zhou <duoming@zju.edu.cn>
Link: https://lore.kernel.org/r/20221002040709.27849-1-duoming@zju.edu.cn
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit c9ab053e56.
The above commit is reverted as it was a prerequisite for tx_mutex
introduction and tx_mutex has been removed as it does not correctly
work in order to protect tx data.
Signed-off-by: Fedor Pchelkin <pchelkin@ispras.ru>
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Reviewed-by: Daniel Starke <daniel.starke@siemens.com>
Link: https://lore.kernel.org/r/20221008110221.13645-3-pchelkin@ispras.ru
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 902e02ea93.
The above commit is reverted as the usage of tx_mutex seems not to solve
the problem described in 902e02ea93 ("tty: n_gsm: avoid call of sleeping
functions from atomic context") and just moves the bug to another place.
Signed-off-by: Fedor Pchelkin <pchelkin@ispras.ru>
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Reviewed-by: Daniel Starke <daniel.starke@siemens.com>
Link: https://lore.kernel.org/r/20221008110221.13645-2-pchelkin@ispras.ru
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A debug bit to output a complete transmission dump exists. Sometimes only
the user frames are relevant. Add an additional bit which limits the
transmission dump output to user data frames if set.
Signed-off-by: Daniel Starke <daniel.starke@siemens.com>
Link: https://lore.kernel.org/r/20220831073800.7459-6-daniel.starke@siemens.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Introduce defines to name the various debug bits used within the code to
improve readability and to make its specific use clear.
Signed-off-by: Daniel Starke <daniel.starke@siemens.com>
Link: https://lore.kernel.org/r/20220831073800.7459-5-daniel.starke@siemens.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Move the content of gsm_control_transmit() to a new function
gsm_control_command() with a more generic signature and analog to
gsm_control_reply(). Use this within gsm_control_transmit().
This is needed to simplify upcoming functional additions.
Signed-off-by: Daniel Starke <daniel.starke@siemens.com>
Link: https://lore.kernel.org/r/20220831073800.7459-4-daniel.starke@siemens.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add a macro which defines the possible number of virtual devices for n_gsm
to improve code readability.
Reviewed-by: Jiri Slaby <jirislaby@kernel.org>
Signed-off-by: Daniel Starke <daniel.starke@siemens.com>
Link: https://lore.kernel.org/r/20220831073800.7459-2-daniel.starke@siemens.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add an enumeration for the gsm mux encoding types to improve code
readability and to avoid invalid values. Only two values are defined by the
standard:
- basic option mode
- advanced option mode (uses ISO HDLC standard transparency mechanism)
Signed-off-by: Daniel Starke <daniel.starke@siemens.com>
Link: https://lore.kernel.org/r/20220831073800.7459-1-daniel.starke@siemens.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Syzkaller reports the following problem:
BUG: sleeping function called from invalid context at kernel/printk/printk.c:2347
in_atomic(): 1, irqs_disabled(): 1, non_block: 0, pid: 1105, name: syz-executor423
3 locks held by syz-executor423/1105:
#0: ffff8881468b9098 (&tty->ldisc_sem){++++}-{0:0}, at: tty_ldisc_ref_wait+0x22/0x90 drivers/tty/tty_ldisc.c:266
#1: ffff8881468b9130 (&tty->atomic_write_lock){+.+.}-{3:3}, at: tty_write_lock drivers/tty/tty_io.c:952 [inline]
#1: ffff8881468b9130 (&tty->atomic_write_lock){+.+.}-{3:3}, at: do_tty_write drivers/tty/tty_io.c:975 [inline]
#1: ffff8881468b9130 (&tty->atomic_write_lock){+.+.}-{3:3}, at: file_tty_write.constprop.0+0x2a8/0x8e0 drivers/tty/tty_io.c:1118
#2: ffff88801b06c398 (&gsm->tx_lock){....}-{2:2}, at: gsmld_write+0x5e/0x150 drivers/tty/n_gsm.c:2717
irq event stamp: 3482
hardirqs last enabled at (3481): [<ffffffff81d13343>] __get_reqs_available+0x143/0x2f0 fs/aio.c:946
hardirqs last disabled at (3482): [<ffffffff87d39722>] __raw_spin_lock_irqsave include/linux/spinlock_api_smp.h:108 [inline]
hardirqs last disabled at (3482): [<ffffffff87d39722>] _raw_spin_lock_irqsave+0x52/0x60 kernel/locking/spinlock.c:159
softirqs last enabled at (3408): [<ffffffff87e01002>] asm_call_irq_on_stack+0x12/0x20
softirqs last disabled at (3401): [<ffffffff87e01002>] asm_call_irq_on_stack+0x12/0x20
Preemption disabled at:
[<0000000000000000>] 0x0
CPU: 2 PID: 1105 Comm: syz-executor423 Not tainted 5.10.137-syzkaller #0
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.12.0-1 04/01/2014
Call Trace:
__dump_stack lib/dump_stack.c:77 [inline]
dump_stack+0x107/0x167 lib/dump_stack.c:118
___might_sleep.cold+0x1e8/0x22e kernel/sched/core.c:7304
console_lock+0x19/0x80 kernel/printk/printk.c:2347
do_con_write+0x113/0x1de0 drivers/tty/vt/vt.c:2909
con_write+0x22/0xc0 drivers/tty/vt/vt.c:3296
gsmld_write+0xd0/0x150 drivers/tty/n_gsm.c:2720
do_tty_write drivers/tty/tty_io.c:1028 [inline]
file_tty_write.constprop.0+0x502/0x8e0 drivers/tty/tty_io.c:1118
call_write_iter include/linux/fs.h:1903 [inline]
aio_write+0x355/0x7b0 fs/aio.c:1580
__io_submit_one fs/aio.c:1952 [inline]
io_submit_one+0xf45/0x1a90 fs/aio.c:1999
__do_sys_io_submit fs/aio.c:2058 [inline]
__se_sys_io_submit fs/aio.c:2028 [inline]
__x64_sys_io_submit+0x18c/0x2f0 fs/aio.c:2028
do_syscall_64+0x33/0x40 arch/x86/entry/common.c:46
entry_SYSCALL_64_after_hwframe+0x61/0xc6
The problem happens in the following control flow:
gsmld_write(...)
spin_lock_irqsave(&gsm->tx_lock, flags) // taken a spinlock on TX data
con_write(...)
do_con_write(...)
console_lock()
might_sleep() // -> bug
As far as console_lock() might sleep it should not be called with
spinlock held.
The patch replaces tx_lock spinlock with mutex in order to avoid the
problem.
Found by Linux Verification Center (linuxtesting.org) with Syzkaller.
Fixes: 32dd59f969 ("tty: n_gsm: fix race condition in gsmld_write()")
Cc: stable <stable@kernel.org>
Signed-off-by: Fedor Pchelkin <pchelkin@ispras.ru>
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Link: https://lore.kernel.org/r/20220829131640.69254-3-pchelkin@ispras.ru
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A kick_timer timer_list is replaced with kick_timeout delayed_work to be
able to synchronize with mutexes as a prerequisite for the introduction
of tx_mutex.
Found by Linux Verification Center (linuxtesting.org) with Syzkaller.
Fixes: c568f7086c ("tty: n_gsm: fix missing timer to handle stalled links")
Cc: stable <stable@kernel.org>
Reviewed-by: Jiri Slaby <jirislaby@kernel.org>
Suggested-by: Hillf Danton <hdanton@sina.com>
Signed-off-by: Fedor Pchelkin <pchelkin@ispras.ru>
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Link: https://lore.kernel.org/r/20220829131640.69254-2-pchelkin@ispras.ru
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
syzbot is reporting use of uninitialized spinlock at gsmld_write() [1], for
commit 32dd59f969 ("tty: n_gsm: fix race condition in gsmld_write()")
allows accessing gsm->tx_lock before gsm_activate_mux() initializes it.
Since object initialization should be done right after allocation in order
to avoid accessing uninitialized memory, move initialization of
timer/work/waitqueue/spinlock from gsmld_open()/gsm_activate_mux() to
gsm_alloc_mux().
Link: https://syzkaller.appspot.com/bug?extid=cf155def4e717db68a12 [1]
Fixes: 32dd59f969 ("tty: n_gsm: fix race condition in gsmld_write()")
Reported-by: syzbot <syzbot+cf155def4e717db68a12@syzkaller.appspotmail.com>
Tested-by: syzbot <syzbot+cf155def4e717db68a12@syzkaller.appspotmail.com>
Cc: stable <stable@kernel.org>
Acked-by: Jiri Slaby <jirislaby@kernel.org>
Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Link: https://lore.kernel.org/r/2110618e-57f0-c1ce-b2ad-b6cacef3f60e@I-love.SAKURA.ne.jp
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A null pointer dereference can happen when attempting to access the
"gsm->receive()" function in gsmld_receive_buf(). Currently, the code
assumes that gsm->recieve is only called after MUX activation.
Since the gsmld_receive_buf() function can be accessed without the need to
initialize the MUX, the gsm->receive() function will not be set and a
NULL pointer dereference will occur.
Fix this by avoiding the call to "gsm->receive()" in case the function is
not initialized by adding a sanity check.
Call Trace:
<TASK>
gsmld_receive_buf+0x1c2/0x2f0 drivers/tty/n_gsm.c:2861
tiocsti drivers/tty/tty_io.c:2293 [inline]
tty_ioctl+0xa75/0x15d0 drivers/tty/tty_io.c:2692
vfs_ioctl fs/ioctl.c:51 [inline]
__do_sys_ioctl fs/ioctl.c:870 [inline]
__se_sys_ioctl fs/ioctl.c:856 [inline]
__x64_sys_ioctl+0x193/0x200 fs/ioctl.c:856
do_syscall_x64 arch/x86/entry/common.c:50 [inline]
do_syscall_64+0x35/0xb0 arch/x86/entry/common.c:80
entry_SYSCALL_64_after_hwframe+0x63/0xcd
Link: https://syzkaller.appspot.com/bug?id=bdf035c61447f8c6e0e6920315d577cb5cc35ac5
Fixes: 01aecd9171 ("tty: n_gsm: fix tty registration before control channel open")
Cc: stable <stable@kernel.org>
Reported-and-tested-by: syzbot+e3563f0c94e188366dbb@syzkaller.appspotmail.com
Signed-off-by: Mazin Al Haddad <mazinalhaddad05@gmail.com>
Link: https://lore.kernel.org/r/20220814015211.84180-1-mazinalhaddad05@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There should be no reason to adjust old ktermios which is going to get
discarded anyway.
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20220816115739.10928-9-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
gsmld_poll() currently fails to handle the following corner cases correctly:
- remote party closed the associated tty
Add the missing checks and map those to EPOLLHUP.
Reorder the checks to group them by their reaction.
Fixes: e1eaea46bb ("tty: n_gsm line discipline")
Signed-off-by: Daniel Starke <daniel.starke@siemens.com>
Link: https://lore.kernel.org/r/20220707113223.3685-4-daniel.starke@siemens.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The current implementation constipates all transmission paths during flow
control except for flow control frames. However, these may not be located
at the beginning of the transmission queue of the control channel.
Ensure that flow control frames in the transmission queue for the control
channel are always handled even if constipated by skipping through other
messages.
Fixes: 0af021678d ("tty: n_gsm: fix deadlock and link starvation in outgoing data path")
Signed-off-by: Daniel Starke <daniel.starke@siemens.com>
Link: https://lore.kernel.org/r/20220707113223.3685-3-daniel.starke@siemens.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
n_gsm is based on the 3GPP 07.010 and its newer version is the 3GPP 27.010.
See https://portal.3gpp.org/desktopmodules/Specifications/SpecificationDetails.aspx?specificationId=1516
The changes from 07.010 to 27.010 are non-functional. Therefore, I refer to
the newer 27.010 here. Chapter 5.3.3 defines the DM response. There exists
no DM command. However, the current implementation incorrectly sends DM as
command in case of unexpected UIH frames in gsm_queue().
Correct this behavior by always sending DM as response.
Fixes: e1eaea46bb ("tty: n_gsm line discipline")
Signed-off-by: Daniel Starke <daniel.starke@siemens.com>
Link: https://lore.kernel.org/r/20220707113223.3685-2-daniel.starke@siemens.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
n_gsm is based on the 3GPP 07.010 and its newer version is the 3GPP 27.010.
See https://portal.3gpp.org/desktopmodules/Specifications/SpecificationDetails.aspx?specificationId=1516
The changes from 07.010 to 27.010 are non-functional. Therefore, I refer to
the newer 27.010 here. Chapter 5.7.3 states that the valid range for the
maximum number of retransmissions (N2) is from 0 to 255 (both including).
gsm_dlci_t1() handles this number incorrectly by performing N2 - 1
retransmission attempts. Setting N2 to zero results in more than 255
retransmission attempts.
Fix gsm_dlci_t1() to comply with 3GPP 27.010.
Fixes: e1eaea46bb ("tty: n_gsm line discipline")
Signed-off-by: Daniel Starke <daniel.starke@siemens.com>
Link: https://lore.kernel.org/r/20220707113223.3685-1-daniel.starke@siemens.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Within gsm_activate_mux() all timers and locks are initiated before the
actual resource for the control channel is allocated. This can lead to race
conditions.
Allocate the control channel DLCI object first to avoid race conditions.
Fixes: e1eaea46bb ("tty: n_gsm line discipline")
Signed-off-by: Daniel Starke <daniel.starke@siemens.com>
Link: https://lore.kernel.org/r/20220701122332.2039-2-daniel.starke@siemens.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The current implementation queues up new control and user packets as needed
and processes this queue down to the ldisc in the same code path.
That means that the upper and the lower layer are hard coupled in the code.
Due to this deadlocks can happen as seen below while transmitting data,
especially during ldisc congestion. Furthermore, the data channels starve
the control channel on high transmission load on the ldisc.
Introduce an additional control channel data queue to prevent timeouts and
link hangups during ldisc congestion. This is being processed before the
user channel data queue in gsm_data_kick(), i.e. with the highest priority.
Put the queue to ldisc data path into a workqueue and trigger it whenever
new data has been put into the transmission queue. Change
gsm_dlci_data_sweep() accordingly to fill up the transmission queue until
TX_THRESH_HI. This solves the locking issue, keeps latency low and provides
good performance on high data load.
Note that now all packets from a DLCI are removed from the internal queue
if the associated DLCI was closed. This ensures that no data is sent by the
introduced write task to an already closed DLCI.
BUG: spinlock recursion on CPU#0, test_v24_loop/124
lock: serial8250_ports+0x3a8/0x7500, .magic: dead4ead, .owner: test_v24_loop/124, .owner_cpu: 0
CPU: 0 PID: 124 Comm: test_v24_loop Tainted: G O 5.18.0-rc2 #3
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.15.0-1 04/01/2014
Call Trace:
<IRQ>
dump_stack_lvl+0x34/0x44
do_raw_spin_lock+0x76/0xa0
_raw_spin_lock_irqsave+0x72/0x80
uart_write_room+0x3b/0xc0
gsm_data_kick+0x14b/0x240 [n_gsm]
gsmld_write_wakeup+0x35/0x70 [n_gsm]
tty_wakeup+0x53/0x60
tty_port_default_wakeup+0x1b/0x30
serial8250_tx_chars+0x12f/0x220
serial8250_handle_irq.part.0+0xfe/0x150
serial8250_default_handle_irq+0x48/0x80
serial8250_interrupt+0x56/0xa0
__handle_irq_event_percpu+0x78/0x1f0
handle_irq_event+0x34/0x70
handle_fasteoi_irq+0x90/0x1e0
__common_interrupt+0x69/0x100
common_interrupt+0x48/0xc0
asm_common_interrupt+0x1e/0x40
RIP: 0010:__do_softirq+0x83/0x34e
Code: 2a 0a ff 0f b7 ed c7 44 24 10 0a 00 00 00 48 c7 c7 51 2a 64 82 e8 2d
e2 d5 ff 65 66 c7 05 83 af 1e 7e 00 00 fb b8 ff ff ff ff <49> c7 c2 40 61
80 82 0f bc c5 41 89 c4 41 83 c4 01 0f 84 e6 00 00
RSP: 0018:ffffc90000003f98 EFLAGS: 00000286
RAX: 00000000ffffffff RBX: 0000000000000000 RCX: 0000000000000000
RDX: 0000000000000000 RSI: ffffffff82642a51 RDI: ffffffff825bb5e7
RBP: 0000000000000200 R08: 00000008de3271a8 R09: 0000000000000000
R10: 0000000000000001 R11: 0000000000000000 R12: 0000000000000000
R13: 0000000000000030 R14: 0000000000000000 R15: 0000000000000000
? __do_softirq+0x73/0x34e
irq_exit_rcu+0xb5/0x100
common_interrupt+0xa4/0xc0
</IRQ>
<TASK>
asm_common_interrupt+0x1e/0x40
RIP: 0010:_raw_spin_unlock_irqrestore+0x2e/0x50
Code: 00 55 48 89 fd 48 83 c7 18 53 48 89 f3 48 8b 74 24 10 e8 85 28 36 ff
48 89 ef e8 cd 58 36 ff 80 e7 02 74 01 fb bf 01 00 00 00 <e8> 3d 97 33 ff
65 8b 05 96 23 2b 7e 85 c0 74 03 5b 5d c3 0f 1f 44
RSP: 0018:ffffc9000020fd08 EFLAGS: 00000202
RAX: 0000000000000000 RBX: 0000000000000246 RCX: 0000000000000000
RDX: 0000000000000004 RSI: ffffffff8257fd74 RDI: 0000000000000001
RBP: ffff8880057de3a0 R08: 00000008de233000 R09: 0000000000000000
R10: 0000000000000001 R11: 0000000000000000 R12: 0000000000000000
R13: 0000000000000100 R14: 0000000000000202 R15: ffff8880057df0b8
? _raw_spin_unlock_irqrestore+0x23/0x50
gsmtty_write+0x65/0x80 [n_gsm]
n_tty_write+0x33f/0x530
? swake_up_all+0xe0/0xe0
file_tty_write.constprop.0+0x1b1/0x320
? n_tty_flush_buffer+0xb0/0xb0
new_sync_write+0x10c/0x190
vfs_write+0x282/0x310
ksys_write+0x68/0xe0
do_syscall_64+0x3b/0x90
entry_SYSCALL_64_after_hwframe+0x44/0xae
RIP: 0033:0x7f3e5e35c15c
Code: 8b 7c 24 08 89 c5 e8 c5 ff ff ff 89 ef 89 44 24 08 e8 58 bc 02 00 8b
44 24 08 48 83 c4 10 5d c3 48 63 ff b8 01 00 00 00 0f 05 <48> 3d 00 f0 ff
ff 76 10 48 8b 15 fd fc 05 00 f7 d8 64 89 02 48 83
RSP: 002b:00007ffcee77cd18 EFLAGS: 00000246 ORIG_RAX: 0000000000000001
RAX: ffffffffffffffda RBX: 00007ffcee77cd70 RCX: 00007f3e5e35c15c
RDX: 0000000000000100 RSI: 00007ffcee77cd90 RDI: 0000000000000003
RBP: 0000000000000100 R08: 0000000000000000 R09: 7efefefefefefeff
R10: 00007f3e5e3bddeb R11: 0000000000000246 R12: 00007ffcee77ce8f
R13: 0000000000000001 R14: 000056214404e010 R15: 00007ffcee77cd90
</TASK>
Fixes: e1eaea46bb ("tty: n_gsm line discipline")
Signed-off-by: Daniel Starke <daniel.starke@siemens.com>
Link: https://lore.kernel.org/r/20220701122332.2039-1-daniel.starke@siemens.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The function may be used by the user directly and also by the n_gsm
internal functions. They can lead into a race condition which results in
interleaved frames if both are writing at the same time. The receiving side
is not able to decode those interleaved frames correctly.
Add a lock around the low side tty write to avoid race conditions and frame
interleaving between user originated writes and n_gsm writes.
Fixes: e1eaea46bb ("tty: n_gsm line discipline")
Signed-off-by: Daniel Starke <daniel.starke@siemens.com>
Link: https://lore.kernel.org/r/20220701061652.39604-9-daniel.starke@siemens.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In the current implementation control packets are re-transmitted even if
the control channel closed down during T2. This is wrong.
Check whether the control channel is open before re-transmitting any
packets. Note that control channel open/close is handled by T1 and not T2
and remains unaffected by this.
Fixes: e1eaea46bb ("tty: n_gsm line discipline")
Signed-off-by: Daniel Starke <daniel.starke@siemens.com>
Link: https://lore.kernel.org/r/20220701061652.39604-7-daniel.starke@siemens.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
n_gsm is based on the 3GPP 07.010 and its newer version is the 3GPP 27.010.
See https://portal.3gpp.org/desktopmodules/Specifications/SpecificationDetails.aspx?specificationId=1516
The changes from 07.010 to 27.010 are non-functional. Therefore, I refer to
the newer 27.010 here. Chapter 5.4.6.3.6 states that FCoff stops the
transmission on all channels except the control channel. This is already
implemented in gsm_data_kick(). However, chapter 5.4.8.1 explains that this
shall result in the same behavior as software flow control on the ldisc in
advanced option mode. That means only flow control frames shall be sent
during flow off. The current implementation does not consider this case.
Change gsm_data_kick() to send only flow control frames if constipated to
abide the standard. gsm_read_ea_val() and gsm_is_flow_ctrl_msg() are
introduced as helper functions for this.
It is planned to use gsm_read_ea_val() in later code cleanups for other
functions, too.
Fixes: c01af4fec2 ("n_gsm : Flow control handling in Mux driver")
Signed-off-by: Daniel Starke <daniel.starke@siemens.com>
Link: https://lore.kernel.org/r/20220701061652.39604-5-daniel.starke@siemens.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The current implementation does not handle the situation that no data is in
the internal queue and needs to be sent out while the user tty fifo is
full.
Add a timer that moves more data from user tty down to the internal queue
which is then serialized on the ldisc. This timer is triggered if no data
was moved from a user tty to the internal queue within 10 * T1.
Fixes: e1eaea46bb ("tty: n_gsm line discipline")
Signed-off-by: Daniel Starke <daniel.starke@siemens.com>
Link: https://lore.kernel.org/r/20220701061652.39604-4-daniel.starke@siemens.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
1) The function drains the fifo for the given user tty/DLCI without
considering 'TX_THRESH_HI' and different to gsm_dlci_data_output_framed(),
which moves only one packet from the user side to the internal transmission
queue. We can only handle one packet at a time here if we want to allow
DLCI priority handling in gsm_dlci_data_sweep() to avoid link starvation.
2) Furthermore, the additional header octet from convergence layer type 2
is not counted against MTU. It is part of the UI/UIH frame message which
needs to be limited to MTU. Hence, it is wrong not to consider this octet.
3) Finally, the waiting user tty is not informed about freed space in its
send queue.
Take at most one packet worth of data out of the DLCI fifo to fix 1).
Limit the max user data size per packet to MTU - 1 in case of convergence
layer type 2 to leave space for the control signal octet which is added in
the later part of the function. This fixes 2).
Add tty_port_tty_wakeup() to wake up the user tty if new write space has
been made available to fix 3).
Fixes: 268e526b93 ("tty/n_gsm: avoid fifo overflow in gsm_dlci_data_output")
Signed-off-by: Daniel Starke <daniel.starke@siemens.com>
Link: https://lore.kernel.org/r/20220701061652.39604-3-daniel.starke@siemens.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The current implementation registers/deregisters the user ttys at mux
attach/detach. That means that the user devices are available before any
control channel is open. However, user channel initialization requires an
open control channel. Furthermore, the user is not informed if the mux
restarts due to configuration changes.
Put the registration/deregistration procedure into separate function to
improve readability.
Move registration to mux activation and deregistration to mux cleanup to
keep the user devices only open as long as a control channel exists. The
user will be informed via the device driver if the mux was reconfigured in
a way that required a mux re-activation.
This makes it necessary to add T2 initialization to gsmld_open() for the
ldisc open code path (not the reconfiguration code path) to avoid deletion
of an uninitialized T2 at mux cleanup.
Fixes: d50f6dcaf2 ("tty: n_gsm: expose gsmtty device nodes at ldisc open time")
Signed-off-by: Daniel Starke <daniel.starke@siemens.com>
Link: https://lore.kernel.org/r/20220701061652.39604-2-daniel.starke@siemens.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
After setting up the control channel on both sides the responder side may
want to open a virtual tty to listen on until the initiator starts an
application on a user channel. The current implementation allows the
open() but no other operation, like termios. These fail with EINVAL.
The responder sided application has no means to detect an open by the
initiator sided application this way. And the initiator sided applications
usually expect the responder sided application to listen on the user
channel upon open.
Set the user channel into half-open state on responder side once a user
application opens the virtual tty to allow IO operations on it.
Furthermore, keep the user channel constipated until the initiator side
opens it to give the responder sided application the chance to detect the
new connection and to avoid data loss if the responder sided application
starts sending before the user channel is open.
Fixes: e1eaea46bb ("tty: n_gsm line discipline")
Signed-off-by: Daniel Starke <daniel.starke@siemens.com>
Link: https://lore.kernel.org/r/20220701061652.39604-1-daniel.starke@siemens.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Dan Carpenter <dan.carpenter@oracle.com> reported the following Smatch
warning:
drivers/tty/n_gsm.c:720 gsm_data_kick()
warn: sleeping in atomic context
This is because gsm_control_message() is holding a spin lock so
gsm_hex_dump_bytes() needs to use GFP_ATOMIC instead of GFP_KERNEL.
Fixes: 925ea0fa52 ("tty: n_gsm: Fix packet data hex dump output")
Cc: stable <stable@kernel.org>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Link: https://lore.kernel.org/r/20220523155052.57129-1-tony@atomide.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The module param debug for n_gsm uses KERN_INFO level, but the hexdump
now uses KERN_DEBUG level. This started after commit 091cb0994e
("lib/hexdump: make print_hex_dump_bytes() a nop on !DEBUG builds").
We now use dynamic_hex_dump() unless DEBUG is set.
This causes no packets to be seen with modprobe n_gsm debug=0x1f unlike
earlier. Let's fix this by adding gsm_hex_dump_bytes() that calls
print_hex_dump() with KERN_INFO to match what n_gsm is doing with the
other debug related output.
Fixes: 091cb0994e ("lib/hexdump: make print_hex_dump_bytes() a nop on !DEBUG builds")
Cc: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Link: https://lore.kernel.org/r/20220512131506.1216-1-tony@atomide.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
gsmtty_write() does not prevent the user to use the full fifo size of 4096
bytes as allocated in gsm_dlci_alloc(). However, gsmtty_write_room() tries
to limit the return value by 'TX_SIZE' and returns a negative value if the
fifo has more than 'TX_SIZE' bytes stored. This is obviously wrong as
'TX_SIZE' is defined as 512.
Define 'TX_SIZE' to the fifo size and use it accordingly for allocation to
keep the current behavior. Return the correct remaining size of the fifo in
gsmtty_write_room() via kfifo_avail().
Fixes: e1eaea46bb ("tty: n_gsm line discipline")
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Starke <daniel.starke@siemens.com>
Link: https://lore.kernel.org/r/20220504081733.3494-3-daniel.starke@siemens.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The current implementation activates the mux if it was restarted and opens
the control channel if the mux was previously closed and we are now acting
as initiator instead of responder, which is the default setting.
This has two issues.
1) No mux is activated if we keep all default values and only switch to
initiator. The control channel is not allocated but will be opened next
which results in a NULL pointer dereference.
2) Switching the configuration after it was once configured while keeping
the initiator value the same will not reopen the control channel if it was
closed due to parameter incompatibilities. The mux remains dead.
Fix 1) by always activating the mux if it is dead after configuration.
Fix 2) by always opening the control channel after mux activation.
Fixes: e1eaea46bb ("tty: n_gsm line discipline")
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Starke <daniel.starke@siemens.com>
Link: https://lore.kernel.org/r/20220504081733.3494-2-daniel.starke@siemens.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
'len' is decreased after each octet that has its EA bit set to 0, which
means that the value is encoded with additional octets. However, the final
octet does not decreases 'len' which results in 'len' being one byte too
long. A buffer over-read may occur in tty_insert_flip_string() as it tries
to read one byte more than the passed content size of 'data'.
Decrease 'len' also for the final octet which has the EA bit set to 1 to
write the correct number of bytes from the internal receive buffer to the
virtual tty.
Fixes: 2e124b4a39 ("TTY: switch tty_flip_buffer_push")
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Starke <daniel.starke@siemens.com>
Link: https://lore.kernel.org/r/20220504081733.3494-1-daniel.starke@siemens.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
'size' may be used uninitialized in gsm_dlci_modem_output() if called with
an adaption that is neither 1 nor 2. The function is currently only called
by gsm_modem_upd_via_data() and only for adaption 2.
Properly handle every invalid case by returning -EINVAL to silence the
compiler warning and avoid future regressions.
Fixes: c19ffe00fe ("tty: n_gsm: fix invalid use of MSC in advanced option")
Cc: stable@vger.kernel.org
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Daniel Starke <daniel.starke@siemens.com>
Link: https://lore.kernel.org/r/20220425104726.7986-1-daniel.starke@siemens.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
n_gsm is based on the 3GPP 07.010 and its newer version is the 3GPP 27.010.
See https://portal.3gpp.org/desktopmodules/Specifications/SpecificationDetails.aspx?specificationId=1516
The changes from 07.010 to 27.010 are non-functional. Therefore, I refer to
the newer 27.010 here. Chapter 5.4.8.1 states that XON/XOFF characters
shall be used instead of Fcon/Fcoff command in advanced option mode to
handle flow control. Chapter 5.4.8.2 describes how XON/XOFF characters
shall be handled. Basic option mode only used Fcon/Fcoff commands and no
XON/XOFF characters. These are treated as data bytes here.
The current implementation uses the gsm_mux field 'constipated' to handle
flow control from the remote peer and the gsm_dlci field 'constipated' to
handle flow control from each DLCI. The later is unrelated to this patch.
The gsm_mux field is correctly set for Fcon/Fcoff commands in
gsm_control_message(). However, the same is not true for XON/XOFF
characters in gsm1_receive().
Disable software flow control handling in the tty to allow explicit
handling by n_gsm.
Add the missing handling in advanced option mode for gsm_mux in
gsm1_receive() to comply with the standard.
This patch depends on the following commit:
Commit 8838b2af23 ("tty: n_gsm: fix SW flow control encoding/handling")
Fixes: e1eaea46bb ("tty: n_gsm line discipline")
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Starke <daniel.starke@siemens.com>
Link: https://lore.kernel.org/r/20220422071025.5490-3-daniel.starke@siemens.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>