Rather than have the MAC drivers manipulate phydev members to indicate
they support Asym Pause, add a helper function.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some MAC hardware cannot support a subset of link modes. e.g. often
1Gbps Full duplex is supported, but Half duplex is not. Add a helper
to remove such a link mode.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a helper for checking whether polling is used to detect PHY status
changes.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some network drivers include functionality to speed down the PHY when
suspending and just waiting for a WoL packet because this saves energy.
This functionality is quite generic, therefore let's factor it out to
phylib.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In struct phy_device we have a number of flags being defined as type
bool. Similar to e.g. struct pci_dev we can save some space by using
bit-fields.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
After commit c59530d0d5 ("net: Move PHY statistics code into PHY
library helpers") we made net/core/ethtool.c reference symbols which are
part of the library which can be modular. David introduced a temporary
fix with 1ecd6e8ad9 ("phy: Temporary build fix after phylib changes.")
which would prevent such modularity.
This is not desireable of course, so instead, just inline the functions
into include/linux/phy.h to keep both options available.
Fixes: c59530d0d5 ("net: Move PHY statistics code into PHY library helpers")
Fixes: 1ecd6e8ad9 ("phy: Temporary build fix after phylib changes.")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to make it possible for network device drivers that do not
necessarily have a phy_device attached, but still report PHY statistics,
have a preliminary refactoring consisting in creating helper functions
that encapsulate the PHY device driver knowledge within PHYLIB.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fun set of conflict resolutions here...
For the mac80211 stuff, these were fortunately just parallel
adds. Trivially resolved.
In drivers/net/phy/phy.c we had a bug fix in 'net' that moved the
function phy_disable_interrupts() earlier in the file, whilst in
'net-next' the phy_error() call from this function was removed.
In net/ipv4/xfrm4_policy.c, David Ahern's changes to remove the
'rt_table_id' member of rtable collided with a bug fix in 'net' that
added a new struct member "rt_mtu_locked" which needs to be copied
over here.
The mlxsw driver conflict consisted of net-next separating
the span code and definitions into separate files, whilst
a 'net' bug fix made some changes to that moved code.
The mlx5 infiniband conflict resolution was quite non-trivial,
the RDMA tree's merge commit was used as a guide here, and
here are their notes:
====================
Due to bug fixes found by the syzkaller bot and taken into the for-rc
branch after development for the 4.17 merge window had already started
being taken into the for-next branch, there were fairly non-trivial
merge issues that would need to be resolved between the for-rc branch
and the for-next branch. This merge resolves those conflicts and
provides a unified base upon which ongoing development for 4.17 can
be based.
Conflicts:
drivers/infiniband/hw/mlx5/main.c - Commit 42cea83f95
(IB/mlx5: Fix cleanup order on unload) added to for-rc and
commit b5ca15ad7e (IB/mlx5: Add proper representors support)
add as part of the devel cycle both needed to modify the
init/de-init functions used by mlx5. To support the new
representors, the new functions added by the cleanup patch
needed to be made non-static, and the init/de-init list
added by the representors patch needed to be modified to
match the init/de-init list changes made by the cleanup
patch.
Updates:
drivers/infiniband/hw/mlx5/mlx5_ib.h - Update function
prototypes added by representors patch to reflect new function
names as changed by cleanup patch
drivers/infiniband/hw/mlx5/ib_rep.c - Update init/de-init
stage list to match new order from cleanup patch
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
For some phy devices, even though they don't support the MMD extended
register access, it does have some side effect if we are trying to
read/write the MMD registers via indirect method. So introduce general
dummy stubs for MMD register access which these devices can use to avoid
such side effect.
Fixes: b6b5e8a691 ("gianfar: Disable EEE autoneg by default")
Signed-off-by: Kevin Hao <haokexin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In 664fcf123a (net: phy: Threaded interrupts allow some simplification)
the phy_interrupt system was changed to use a traditional threaded
interrupt scheme instead of a workqueue approach.
With this change, the phy status check moved into phy_change, which
did not report back to the caller whether or not the interrupt was
handled. This means that, in the case of a shared phy interrupt,
only the first phydev's interrupt registers are checked (since
phy_interrupt() would always return IRQ_HANDLED). This leads to
interrupt storms when it is a secondary device that's actually the
interrupt source.
Signed-off-by: Brad Mouring <brad.mouring@ni.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
All of the conflicts were cases of overlapping changes.
In net/core/devlink.c, we have to make care that the
resouce size_params have become a struct member rather
than a pointer to such an object.
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to remove a fair amount of duplication in the different 10G PHY
drivers, export all gen10g_* functions to be able to make use of those.
While we are at it, rename gen10g_soft_reset() to gen10g_no_soft_reset()
to illustrate what it does.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
commit f5e64032a7 ("net: phy: fix resume handling") changes the
locking semantics for phy_resume() such that the caller now needs to
hold the phy mutex. Not all call sites were adopted to this new
semantic, resulting in warnings from the added
WARN_ON(!mutex_is_locked(&phydev->lock)). Rather than change the
semantics, add a __phy_resume() and restore the old behavior of
phy_resume().
Reported-by: Heiner Kallweit <hkallweit1@gmail.com>
Fixes: f5e64032a7 ("net: phy: fix resume handling")
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Based on the recent introduction of phy_modify add helpers for setting
and clearing bits in PHY registers.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
I see two issues with parameter new_link:
1. It's not needed. See also phy_interrupt(), works w/o this parameter.
phy_mac_interrupt sets the state to PHY_CHANGELINK and triggers the
state machine which then calls phy_read_status. And phy_read_status
updates the link state.
2. phy_mac_interrupt is used in interrupt context and getting the link
state may sleep (at least when having to access the PHY registers
via MDIO bus).
So let's remove it.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Tested-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add phy_modify() convenience accessor to complement the mdiobus
counterpart.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a set of paged phy register accessors which are inherently safe in
their design against other accesses interfering with the paged access.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add unlocked versions of the bus accessors, which allows access to the
bus with all the tracing. These accessors validate that the bus mutex
is held, which is a basic requirement for all mii bus accesses.
Also added is a read-modify-write unlocked accessor with the same
locking requirements.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a helper to convert the result of the autonegotiation advertisment
into the PHYs speed and duplex settings. If the result is full duplex,
also extract the pause mode settings from the link partner advertisment.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add reporting of the MDI swap to the Marvell 10G PHY driver by providing
a generic implementation for the standard 10GBASE-T pair swap register
and polarity register. We also support reading the MDI swap status for
1G and below from a PCS register.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some PHYs need the refclk to be a continuous clock. Therefore they don't
allow turning it off and on again during operation. Nonetheless such a
clock switching is performed by some ETH drivers (namely FEC [1]) for
power saving reasons. An example for an affected PHY is the
SMSC/Microchip LAN8720 in "REF_CLK In Mode".
In order to provide a uniform method to overcome this problem this patch
adds a new phy_driver flag (PHY_RST_AFTER_CLK_EN) and corresponding
function phy_reset_after_clk_enable() to the phylib. These should be
used to trigger reset of the PHY after the refclk is switched on again.
[1] commit e8fcfcd568 ("net: fec: optimize the clock management to save power")
Signed-off-by: Richard Leitner <richard.leitner@skidata.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The PHY devices sometimes do have their reset signal (maybe even power
supply?) tied to some GPIO and sometimes it also does happen that a boot
loader does not leave it deasserted. So far this issue has been attacked
from (as I believe) a wrong angle: by teaching the MAC driver to manipulate
the GPIO in question; that solution, when applied to the device trees, led
to adding the PHY reset GPIO properties to the MAC device node, with one
exception: Cadence MACB driver which could handle the "reset-gpios" prop
in a PHY device subnode. I believe that the correct approach is to teach
the 'phylib' to get the MDIO device reset GPIO from the device tree node
corresponding to this device -- which this patch is doing...
Note that I had to modify the AT803x PHY driver as it would stop working
otherwise -- it made use of the reset GPIO for its own purposes...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Acked-by: Rob Herring <robh@kernel.org>
[geert: Propagate actual errors from fwnode_get_named_gpiod()]
[geert: Avoid destroying initial setup]
[geert: Consolidate GPIO descriptor acquiring code]
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Tested-by: Richard Leitner <richard.leitner@skidata.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add and use phy_interface_mode_is_8023z() helper to identify the
interface modes that use 802.3z negotiation. Use it in phylink's
phylink_mac_an_restart().
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After commits c974bdbc3e "net: phy: Use threaded IRQ, to allow IRQ from
sleeping devices" and 664fcf123a "net: phy: Threaded interrupts allow
some simplification" all relevant code pieces run in process context
anyway and I don't think we need the disabling of interrupts any longer.
Interestingly enough, latter commit already removed the comment
explaining why interrupts need to be temporarily disabled.
On my system phy interrupt mode works fine with this patch.
However I may miss something, especially in the context of shared phy
interrupts, therefore I'd appreciate if more people could test this.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Acked-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
read_status and config_aneg are the only mandatory callbacks and most
of the time the generic implementation is used by drivers.
So make the core fall back to the generic version if a driver doesn't
implement the respective callback.
Also currently the core doesn't seem to verify that drivers implement
the mandatory calls. If a driver doesn't do so we'd just get a NPE.
With this patch this potential issue doesn't exit any longer.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Previously phy_id was u32 and phy_id_mask was unsigned int. As the
phy_id_mask defines the important bits of the phy_id (and is therefore
the same size) these two variables should be the same data type.
Signed-off-by: Richard Leitner <richard.leitner@skidata.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, we create a LED trigger for any link speed known to a PHY.
These triggers only fire when their exact link speed had been negotiated
(they aren't cumulative, that is, they don't fire for "their or any higher"
link speed).
What we are missing, however, is a trigger which will fire on any link
speed known to the PHY. Such trigger can then be used for implementing a
poor man's substitute of the "link" LED on boards that lack it.
Let's add it.
Signed-off-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Signed-off-by: David S. Miller <davem@davemloft.net>
The link between the ethernet MAC and its PHY has become more complex
as the interface evolves. This is especially true with serdes links,
where the part of the PHY is effectively integrated into the MAC.
Serdes links can be connected to a variety of devices, including SFF
modules soldered down onto the board with the MAC, a SFP cage with
a hotpluggable SFP module which may contain a PHY or directly modulate
the serdes signals onto optical media with or without a PHY, or even
a classical PHY connection.
Moreover, the negotiation information on serdes links comes in two
varieties - SGMII mode, where the PHY provides its speed/duplex/flow
control information to the MAC, and 1000base-X mode where both ends
exchange their abilities and each resolve the link capabilities.
This means we need a more flexible means to support these arrangements,
particularly with the hotpluggable nature of SFP, where the PHY can
be attached or detached after the network device has been brought up.
Ethtool information can come from multiple sources:
- we may have a PHY operating in either SGMII or 1000base-X mode, in
which case we take ethtool/mii data directly from the PHY.
- we may have a optical SFP module without a PHY, with the MAC
operating in 1000base-X mode - the ethtool/mii data needs to come
from the MAC.
- we may have a copper SFP module with a PHY whic can't be accessed,
which means we need to take ethtool/mii data from the MAC.
Phylink aims to solve this by providing an intermediary between the
MAC and PHY, providing a safe way for PHYs to be hotplugged, and
allowing a SFP driver to reconfigure the serdes connection.
Phylink also takes over support of fixed link connections, where the
speed/duplex/flow control are fixed, but link status may be controlled
by a GPIO signal. By avoiding the fixed-phy implementation, phylink
can provide a faster response to link events: fixed-phy has to wait for
phylib to operate its state machine, which can take several seconds.
In comparison, phylink takes milliseconds.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
- remove sync status
- rework supported and advertisment handling
- add 1000base-x speed for fixed links
- use functionality exported from phy-core, reworking
__phylink_ethtool_ksettings_set for it
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sometimes, we need to do additional work between the PHY coming up and
marking the carrier present - for example, we may need to wait for the
PHY to MAC link to finish negotiation. This changes phylib to provide
a notification function pointer which avoids the built-in
netif_carrier_on() and netif_carrier_off() functions.
Standard ->adjust_link functionality is provided by hooking a helper
into the new ->phy_link_change method.
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
phy_lookup_setting() provides useful functionality in ethtool code
outside phylib. Move it to phy-core and allow it to be re-used (eg,
in phylink) rather than duplicated elsewhere. Note that this supports
the larger linkmode space.
As we move the phy settings table, we also need to move the guts of
phy_supported_speeds() as well.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Other code would like to make use of this, so make the speed and duplex
string generation visible, and place it in a separate file.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit e5a03bfd87 ("phy: Add an mdio_device structure")
introduced a spurious trailing semicolon. Remove it.
Signed-off-by: Marc Gonzalez <marc_gonzalez@sigmadesigns.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch add set_loopback in phy_driver, which is used by MAC
driver to enable or disable phy loopback. it also add a generic
genphy_loopback function, which use BMCR loopback bit to enable
or disable loopback.
Signed-off-by: Lin Yun Sheng <linyunsheng@huawei.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that the Device Tree binding has been updated, update the PHY
library phy_interface_t and phy_modes to support the "internal" PHY
interface type.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make return value void since function never return meaningfull value
Signed-off-by: Yuval Shaia <yuval.shaia@oracle.com>
Acked-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 4c5e7a2c05 ("dt-bindings: mdio: Clarify binding document")
declared that a MDIO reset GPIO property should have only a single GPIO
reference/specifier, however the supporting code was left intact, still
burdening the kernel with now apparently useless loops -- get rid of them.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
XAUI allows XGMII to reach an extended distance by using a XGXS layer at
each end of the MAC to PHY link, operating over four Serdes lanes.
10GBASE-KR is a single lane Serdes backplane ethernet connection method
with autonegotiation on the link. Some PHYs use this to connect to the
ethernet interface at 10G speeds, switching to other connection types
when utilising slower speeds.
10GBASE-KR is also used for XFI and SFI to connect to XFP and SFP fiber
modules.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
genphy_restart_aneg() can only restart autonegotiation on clause 22
PHYs. Add a phy_restart_aneg() function which selects between the
clause 22 and clause 45 restart functionality depending on the PHY
type and whether the Clause 45 PHY supports the Clause 22 register set.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add generic helpers for 802.3 clause 45 PHYs for >= 10Gbps support.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It's unused, so remove it.
Signed-off-by: Yuval Shaia <yuval.shaia@oracle.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some Ethernet drivers will attach/connect to a PHY device before calling
register_netdevice() which is responsible for calling netdev_register_kobject()
which would do the network device's kobject initialization. In such a case,
sysfs_create_link() would return -ENOENT because the network device's kobject
is not ready yet, and we would fail to connect to the PHY device.
In order to keep things simple and symetrical, we just take the success path as
indicative of the ability to access the network device's kobject, and create
the second link if that's the case.
Fixes: 5568363f0c ("net: phy: Create sysfs reciprocal links for attached_dev/phydev")
Reported-by: Woojung Hung <Woojung.Huh@microchip.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Added helper function that checks phy_mode is RGMII (all variants)
'bool phy_interface_mode_is_rgmii(phy_interface_t mode)'
Changed the following function, to use the above.
'bool phy_interface_is_rgmii(struct phy_device *phydev)'
Signed-off-by: Iyappan Subramanian <isubramanian@apm.com>
Suggested-by: Florian Fainelli <f.fainelli@gmail.com>
Suggested-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit fa8cddaf90 ("net phylib: Remove unnecessary condition check in phy")
removed the only place where the PHY flag PHY_HAS_MAGICANEG was
checked. But it left the flag being set in the drivers. Remove the flag.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Ethernet link on an interrupt driven PHY was not coming up if the Ethernet
cable was plugged before the Ethernet interface was brought up.
The patch trigger PHY state machine to update link state if PHY was requested to
do auto-negotiation and auto-negotiation complete flag already set.
During power-up cycle the PHY do auto-negotiation, generate interrupt and set
auto-negotiation complete flag. Interrupt is handled by PHY state machine but
doesn't update link state because PHY is in PHY_READY state. After some time
MAC bring up, start and request PHY to do auto-negotiation. If there are no new
settings to advertise genphy_config_aneg() doesn't start PHY auto-negotiation.
PHY continue to stay in auto-negotiation complete state and doesn't fire
interrupt. At the same time PHY state machine expect that PHY started
auto-negotiation and is waiting for interrupt from PHY and it won't get it.
Fixes: 321beec504 ("net: phy: Use interrupts when available in NOLINK state")
Signed-off-by: Alexander Kochetkov <al.kochet@gmail.com>
Cc: stable <stable@vger.kernel.org> # v4.9+
Tested-by: Roger Quadros <rogerq@ti.com>
Tested-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some boards [1] leave the PHYs at an invalid state
during system power-up or reset thus causing unreliability
issues with the PHY which manifests as PHY not being detected
or link not functional. To fix this, these PHYs need to be RESET
via a GPIO connected to the PHY's RESET pin.
Some boards have a single GPIO controlling the PHY RESET pin of all
PHYs on the bus whereas some others have separate GPIOs controlling
individual PHY RESETs.
In both cases, the RESET de-assertion cannot be done in the PHY driver
as the PHY will not probe till its reset is de-asserted.
So do the RESET de-assertion in the MDIO bus driver.
[1] - am572x-idk, am571x-idk, a437x-idk
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce a new configuration symbol: MDIO_DEVICE which allows building
the MDIO devices and bus code, without pulling in the entire Ethernet
PHY library and devices code.
PHYLIB nows select MDIO_DEVICE and the relevant Makefile files are
updated to reflect that.
When MDIO_DEVICE (MDIO bus/device only) is selected, but not PHYLIB, we
have mdio-bus.ko as a loadable module, and it does not have a
module_exit() function because the safety of removing a bus class is
unclear.
When both MDIO_DEVICE and PHYLIB are enabled, we need to assemble
everything into a common loadable module: libphy.ko because of nasty
circular dependencies between phy.c, phy_device.c and mdio_bus.c which
are really tough to untangle.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove the indirect MMD read/write methods which are now no longer
necessary.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make phy_(read|write)_mmd() generic 802.3 clause 45 register accessors
for both Clause 22 and Clause 45 PHYs, using either the direct register
reading for Clause 45, or the indirect method for Clause 22 PHYs.
Allow this behaviour to be overriden by PHY drivers where necessary.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the phy_(read|write)__mmd() helpers out of line, they will become
our main MMD accessor functions, and so will be a little more complex.
This complexity doesn't belong in an inline function. Also move the
_indirect variants as well to keep like functionality together.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Generic PHY driver is a catch-all PHY driver and it should preserve
whatever prior initialization has been done by boot loader or firmware
agents. For specific PHY device configuration it is expected that a
specialized PHY driver would take over that role.
Resetting the generic PHY was a bad idea that has lead to several
complaints and downstream workarounds e.g: in OpenWrt/LEDE so restore
the behavior prior to 87aa9f9c61 ("net: phy: consolidate PHY
reset in phy_init_hw()").
Reported-by: Felix Fietkau <nbd@nbd.name>
Fixes: 87aa9f9c61 ("net: phy: consolidate PHY reset in phy_init_hw()")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are number of function calls, originating from user-space,
typically through the Ethernet driver that can make us crash by
dereferencing phydev->drv which will be NULL once we unbind the driver
from the PHY.
There are still functional issues that prevent an unbind then rebind to
work, but these will be addressed separately.
Suggested-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow board support code to collect pre-declarations for MDIO devices by
registering them with mdiobus_register_board_info(). SPI and I2C buses
have a similar feature, we were missing this for MDIO devices, but this
is particularly useful for e.g: MDIO-connected switches which need to
provide their port layout (often board-specific) to a MDIO Ethernet
switch driver.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mv88e6390 ports 9 and 10 supports some additional PHY modes. Add
these modes to the PHY core so they can be used in the binding.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
<linux/phy.h> includes <linux/phy_led_triggers.h>, which is not really
needed. Drop the include from <linux/phy.h>, and add it to all users
that didn't include it explicitly.
Suggested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some bus names are pretty long and do not fit into
17 chars. Increase therefore MII_BUS_ID_SIZE and
phy_fixup.bus_id to larger number. Now mii_bus.id
can host larger name.
Signed-off-by: Volodymyr Bendiuga <volodymyr.bendiuga@gmail.com>
Signed-off-by: Magnus Öberg <magnus.oberg@westermo.se>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
>From : Woojung Huh <woojung.huh@microchip.com>
Add functions to unregister phy fixup for modules.
int phy_unregister_fixup(const char *bus_id, u32 phy_uid, u32 phy_uid_mask)
Unregister phy fixup from phy_fixup_list per bus_id, phy_uid &
phy_uid_mask
int phy_unregister_fixup_for_uid(u32 phy_uid, u32 phy_uid_mask)
Unregister phy fixup from phy_fixup_list.
Use it for fixup registered by phy_register_fixup_for_uid()
int phy_unregister_fixup_for_id(const char *bus_id)
Unregister phy fixup from phy_fixup_list.
Use it for fixup registered by phy_register_fixup_for_id()
Signed-off-by: Woojung Huh <woojung.huh@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add new parameter mdix_ctrl to hold the user configuration.
Existing mdix maintain the current status of MDI(X) crossover performed or
not.
mdix_ctrl can configure either ETH_TP_MDI or ETH_TP_MDI_X orETH_TP_MDI_AUTO.
Signed-off-by: Raju Lakkaraju <Raju.Lakkaraju@microsemi.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds an option to disable EEE advertisement in the generic PHY
by providing a mask of prohibited modes corresponding to the value found in
the MDIO_AN_EEE_ADV register.
On some platforms, PHY Low power idle seems to be causing issues, even
breaking the link some cases. The patch provides a convenient way for these
platforms to disable EEE advertisement and work around the issue.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Tested-by: Yegor Yefremov <yegorslists@googlemail.com>
Tested-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adding get_tunable/set_tunable function pointer to the phy_driver
structure, and uses these function pointers to implement the
ETHTOOL_PHY_GTUNABLE/ETHTOOL_PHY_STUNABLE ioctls.
Signed-off-by: Raju Lakkaraju <Raju.Lakkaraju@microsemi.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Allan W. Nielsen <allan.nielsen@microsemi.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This function just calls into genphy_restart_aneg() to perform an
autonegotation restart.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make phy_aneg_done() available to drivers so that the result of the
auto-negotiation initiated by phy_start_aneg() can be determined.
Remove the local implementation of phy_aneg_done() from the Aeroflex
driver and use the phy library version.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Create an option CONFIG_LED_TRIGGER_PHY (default n), which will create a
set of led triggers for each instantiated PHY device. There is one LED
trigger per link-speed, per-phy.
The triggers are registered during phy_attach and unregistered during
phy_detach.
This allows for a user to configure their system to allow a set of LEDs
not controlled by the phy to represent link state changes on the phy.
LEDS controlled by the phy are unaffected.
For example, we have a board where some of the leds in the
RJ45 socket are controlled by the phy, but others are not. Using the
triggers provided by this patch the leds not controlled by the phy can
be configured to show the current speed of the ethernet connection. The
leds controlled by the phy are unaffected.
Signed-off-by: Josh Cartwright <josh.cartwright@ni.com>
Signed-off-by: Nathan Sullivan <nathan.sullivan@ni.com>
Signed-off-by: Zach Brown <zach.brown@ni.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
phy_supported_speeds provides a means to get a list of all the speeds a
phy device currently supports.
Signed-off-by: Zach Brown <zach.brown@ni.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The PHY interrupts are now handled in a threaded interrupt handler,
which can sleep. The work queue is no longer needed, phy_change() can
be called directly. phy_mac_interrupt() still needs to be safe to call
in interrupt context, so keep the work queue, and use a helper to call
phy_change().
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
adds PHY-mode "trgmii" as an extension for the operation
mode of the PHY interface for PHY_INTERFACE_MODE_TRGMII.
and adds a variable trgmii inside mtk_mac as the indication
to make the difference between the MAC connected to internal
switch or connected to external PHY by the given configuration
on the board and then to perform the corresponding setup on
TRGMII hardware module.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ethtool callbacks {get|set}_link_ksettings are often the same, so
we add two generics functions phy_ethtool_{get|set}_link_ksettings
to avoid writing severals times the same function.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Acked-By: David Decotigny <decot@googlers.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The old ethtool api (get_setting and set_setting) has
generic phy functions phy_ethtool_sset and phy_ethtool_gset.
To supprt the new ethtool api (get_link_ksettings and
set_link_ksettings), we add generic phy function
phy_ethtool_ksettings_get and phy_ethtool_ksettings_set.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit e5a03bfd87 ("phy: Add an mdio_device structure") removed addr,
bus and dev member of the phy_device structure.
This patch remove the documentation about those members.
Signed-off-by: LABBE Corentin <clabbe.montjoie@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Not all devices on an MDIO bus are PHYs. Meaning not all MDIO drivers
are PHY drivers. Add support for generic MDIO drivers.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rather than have each driver set the driver owner field, do it once in
the core code. This will also help with later changes, when the device
structure will move.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rather than have drivers directly manipulate the mii_bus structure,
provide and API for registering and unregistering devices on an MDIO
bus, and performing lookups.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Not all devices attached to an MDIO bus are phys. So add an
mdio_device structure to represent the generic parts of an mdio
device, and place this structure into the phy_device.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Have mdio_alloc() create the array of interrupt numbers, and
initialize it to POLLING. This is what most MDIO drivers want, so
allowing code to be removed from the drivers.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Many Ethernet drivers contain the same netdev_info() print statement
about the attached phy. Move it into the phy device code. Additionally
add a varargs function which can be used to append additional
information.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The address of the device can be determined from the phydev structure,
rather than passing it as a parameter.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a phydev_name() function, to help with moving some structure members
from phy_device.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation for moving some of the phy_device structure members,
add macros for printing errors and debug information.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
These are logically MDIO operations, not phy operations, so move them
into the mdio header.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Within phy.h, an address on an MII bus has been called both addr and
phy_id. phy_id is particularly confusion, since it also means the ID
found in register 3, if the device on the bus is a phy. Consistently
use addr.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ethernet PHYs can maintain statistics, for example errors while idle
and receive errors. Add an ethtool mechanism to retrieve these
statistics, using the same model as MAC statistics.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since nested variants of mdiobus_read/write are used in multiple
drivers, add nested variants in the mdiobus core.
Suggested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a helper to allow ethernet drivers to limit the speed of a phy
(that they are attached to).
This mainly involves factoring out the business-end of
of_set_phy_supported() and exporting a new symbol.
This code seems to be open coded in several places, in several different
variants.
It is is envisaged that this will be used in situations where setting the
"max-speed" property in DT is not appropriate, e.g. because the maximum
speed is not a property of the phy hardware.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a phy_device_remove() function to complement phy_device_register(),
which undoes the effects of phy_device_register() by removing the phy
device from visibility, but not freeing it.
This allows these details to be moved out of the mdio bus code into
the phy code where this action belongs.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Re-implement the mdiobus module refcounting to ensure that we actually
ensure that the mdiobus module code does not go away while we might call
into it.
The old scheme using bus->dev.driver was buggy, because bus->dev is a
class device which never has a struct device_driver associated with it,
and hence the associated code trying to obtain a refcount did nothing
useful.
Instead, take the approach that other subsystems do: pass the module
when calling mdiobus_register(), and record that in the mii_bus struct.
When we need to increment the module use count in the phy code, use
this stored pointer. When the phy is deteched, drop the module
refcount, remembering that the phy device might go away at that point.
This doesn't stop the mii_bus going away while there are in-use phys -
it merely stops the underlying code vanishing.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some Ethernet MAC drivers using the PHY library require the hardcoding
of link parameters when interfaced to a switch device, SFP module,
switch to switch port, etc. This has typically lead to various ad-hoc
implementations looking like this:
- using a "fixed PHY" emulated device, which will provide link
indication towards the Ethernet MAC driver and hardware
- pretend there is no PHY and hardcode link parameters, ala mv643x_eth
Based on that, it is desireable to have the PHY drivers advertise the
correct link parameters, just like regular Ethernet PHYs towards their
CPU Ethernet MAC drivers, however, Ethernet MAC drivers should be able
to tell whether this link should be monitored or not. In the context
of an Ethernet switch, SFP module, switch to switch link, we do not
need to monitor this link since it should be always up.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pass the mdix setting from ethtool down to the phy driver, to allow
driver specific implementations of manually setting the polarity.
Signed-off-by: David Thomson <david.thomson@alliedtelesis.co.nz>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
RGMII interfaces come in 4 different flavors that the PHY library needs
to care about: regular RGMII (no delays), RGMII with either RX or TX
delay, and both. In order to avoid errors of checking only for one type
of RGMII interface and miss the 3 others, introduce a convenience
function which tests for all values.
Suggested-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some PHY devices/switches will not release the turn-around line as they
should do at the end of a MDIO transaction. To help with such
situations, allow MDIO bus drivers to be made aware of such
restrictions.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to avoid double calls to phydev->drv->suspend and resume, keep
track of whether the PHY has already been suspended as a consequence of
a successful call to phy_suspend(). We will use this in our MDIO bus
suspend/resume hooks to avoid a double suspend call.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
has_fixups was introduced to help keeping track of fixups/quirks running
on a PHY device, but we did not update the comment above struct
phy_device accordingly.
Fixes: b0ae009f3d (net: phy: add "has_fixups" boolean property")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch extends the ethtool plugin module eeprom API to support cards
whose phy support is delegated to a separate driver.
The handlers for ETHTOOL_GMODULEINFO and ETHTOOL_GMODULEEEPROM call the
module_info and module_eeprom functions if the phy driver provides them;
otherwise the handlers call the equivalent ethtool_ops functions provided
by network drivers with built-in phy support.
Signed-off-by: Ed Swierk <eswierk@skyportsystems.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add static driver-data field to struct phy_driver, which can be used to
store structured device-type information.
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add helper macro for PHY drivers which do not do anything special in
module init/exit. This will allow us to eliminate a lot of boilerplate
code.
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some PHY drivers might need to access Clause 45 registers in Clause 22
compatibility mode to e.g: properly advertise EEE support when disabled
by default.
Export these two helper functions: phy_read_mmd_indirect() and
phy_write_mmd_indirect() for drivers to use them.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
libphy was originally written assuming all phy devices support clause 45
access extensions to the mmd registers through the indirection registers
located within the first 16 phy registers. This assumption is not true
in all cases, and one specific example is the Micrel ksz9021 10/100/1000
Mbps phy. Using the stmmac driver, accessing the mmd registers to query
and configure energy efficient Ethernet (EEE) features yielded unexpected
behavior.
This patch adds mmd access functions to the phy driver that can be
overriden by the phy specific driver if the phy does not support this
mechanism or uses it's own non-standard access mechanism. By default,
the IEEE Compatible clause 45 access mechanism described in clause 22
is used. With this patch, EEE query/configure functions as expected
using the stmmac and the Micrel ksz9021 phy.
Signed-off-by: Vince Bridgers <vbridgers2013@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a notify callback to inform phy drivers when the core is about to
do its link adjustment. No change for drivers that do not implement
this callback.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a resource managed devm_mdiobus_alloc[_size]()/devm_mdiobus_free()
to automatically clean up MDIO bus alocations made by MDIO drivers,
thus leading to simplified MDIO drivers code.
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Acked-and-tested-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This enables other drivers to call this generic implementation, and then
only do specific details on top of it.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Andrew Lunn
Heiner Kallweit
Florian Fainelli
David S. Miller
Kevin Hao
Brad Mouring
Russell King
Richard Leitner
Sergei Shtylyov
Maciej S. Szmigiero
Russell King
Marc Gonzalez
Lin Yun Sheng
yuval.shaia@oracle.com
Iyappan Subramanian
Alexander Kochetkov
Roger Quadros
Geert Uytterhoeven
Volodymyr Bendiuga
Woojung.Huh@microchip.com
Raju Lakkaraju
jbrunet
Lendacky, Thomas
Zach Brown
Sean Wang
Philippe Reynes
LABBE Corentin
Neil Armstrong
Simon Horman
David Thomson
Ed Swierk
Johan Hovold
Vince Bridgers
Daniel Mack
Grygorii Strashko