One of the first steps of log recovery is to check for the special
case of a zeroed log. If the first cycle in the log is zero or the
tail portion of the log is zeroed, the head is set to the first
instance of cycle 0. xlog_find_zeroed() includes a sanity check that
enforces that the first cycle in the log must be 1 if the last cycle
is 0. While this is true in most cases, the check is not totally
valid because it doesn't consider the case where the filesystem
crashed after a partial/out of order log buffer completion that
wraps around the end of the physical log.
For example, consider a filesystem that has completed most of the
first cycle of the log, reaches the end of the physical log and
splits the next single log buffer write into two in order to wrap
around the end of the log. If these I/Os are reordered, the second
(wrapped) I/O completes and the first happens to fail, the log is
left in a state where the last cycle of the log is 0 and the first
cycle is 2. This causes the xlog_find_zeroed() sanity check to fail
and prevents the filesystem from mounting. This situation has been
reproduced on particular systems via repeated runs of generic/475.
This is an expected state that log recovery already knows how to
deal with, however. Since the log is still partially zeroed, the
head is detected correctly and points to a valid tail. The
subsequent stale block detection clears blocks beyond the head up to
the tail (within a maximum range), with the express purpose of
clearing such out of order writes. As expected, this removes the out
of order cycle 2 blocks at the physical start of the log.
In other words, the only thing that prevents a clean mount and
recovery of the filesystem in this scenario is the specific (last ==
0 && first != 1) sanity check in xlog_find_zeroed(). Since the log
head/tail are now independently validated via cycle, log record and
CRC checks, this highly specific first cycle check is of dubious
value. Remove it and rely on the higher level validation to
determine whether log content is sane and recoverable.
Signed-off-by: Brian Foster <bfoster@redhat.com>
Reviewed-by: Dave Chinner <dchinner@redhat.com>
Signed-off-by: Dave Chinner <david@fromorbit.com>
All callers pass ->t_dfops of the associated transactions. Refactor
the helpers to receive the transactions and facilitate further
cleanups between xfs_defer_ops and xfs_trans.
Signed-off-by: Brian Foster <bfoster@redhat.com>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Log intent recovery is the last user of an external (on-stack)
dfops. The pattern exists because the dfops is used to collect
additional deferred operations queued during the whole recovery
sequence. The dfops is finished with a new transaction after intent
recovery completes.
We already have a mechanism to create an empty, container-like
transaction to support the scrub infrastructure. We can reuse that
mechanism here to drop the final user of external dfops. This
facilitates folding dfops state (i.e., dop_low) into the
transaction, the elimination of now unused external dfops support
and also eliminates the only caller of __xfs_defer_cancel().
Replace the on-stack dfops with an empty transaction and pass it
around to the various helpers that queue and finish deferred
operations during intent recovery.
Signed-off-by: Brian Foster <bfoster@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Replace the IRELE macro with a proper function so that we can do proper
typechecking and so that we can stop open-coding iput in scrub, which
means that we'll be able to ftrace inode lifetimes going through scrub
correctly.
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Reviewed-by: Carlos Maiolino <cmaiolino@redhat.com>
Reviewed-by: Brian Foster <bfoster@redhat.com>
Every caller of xfs_defer_finish() now passes the transaction and
its associated ->t_dfops. The xfs_defer_ops parameter is therefore
no longer necessary and can be removed.
Since most xfs_defer_finish() callers also have to consider
xfs_defer_cancel() on error, update the latter to also receive the
transaction for consistency. The log recovery code contains an
outlier case that cancels a dfops directly without an available
transaction. Retain an internal wrapper to support this outlier case
for the time being.
Signed-off-by: Brian Foster <bfoster@redhat.com>
Reviewed-by: Bill O'Donnell <billodo@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
At this point, the transaction subsystem completely manages deferred
items internally such that the common and boilerplate
xfs_trans_alloc() -> xfs_defer_init() -> xfs_defer_finish() ->
xfs_trans_commit() sequence can be replaced with a simple
transaction allocation and commit.
Remove all such boilerplate deferred ops code. In doing so, we
change each case over to use the dfops in the transaction and
specifically eliminate:
- The on-stack dfops and associated xfs_defer_init() call, as the
internal dfops is initialized on transaction allocation.
- xfs_bmap_finish() calls that precede a final xfs_trans_commit() of
a transaction.
- xfs_defer_cancel() calls in error handlers that precede a
transaction cancel.
The only deferred ops calls that remain are those that are
non-deterministic with respect to the final commit of the associated
transaction or are open-coded due to special handling.
Signed-off-by: Brian Foster <bfoster@redhat.com>
Reviewed-by: Bill O'Donnell <billodo@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
bmap and refcount intent processing associates a dfops from the
caller with a local transaction to collect all deferred items for
post-processing. Use the internal dfops in both of these functions
and move the deferred items to the parent dfops before the
transaction commits.
Signed-off-by: Brian Foster <bfoster@redhat.com>
Reviewed-by: Bill O'Donnell <billodo@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
xlog_finish_defer_ops() processes the deferred operations collected
over the entire intent recovery sequence. We can't xfs_defer_init()
here because the dfops is already populated. Attach it manually and
eliminate the last caller of xfs_defer_finish() that doesn't pass
->t_dfops.
Signed-off-by: Brian Foster <bfoster@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Bill O'Donnell <billodo@redhat.com>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
The buffer I/O submission path consists of separate function calls
per type. The buffer I/O type is already controlled via buffer
state (XBF_ASYNC), however, so there is no real need for separate
submission functions.
Combine the buffer submission functions into a single function that
processes the buffer appropriately based on XBF_ASYNC. Retain an
internal helper with a conditional wait parameter to continue to
support batched !XBF_ASYNC submission/completion required by delwri
queues.
Suggested-by: Christoph Hellwig <hch@infradead.org>
Signed-off-by: Brian Foster <bfoster@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
All but one caller of xfs_defer_init() passes in the ->t_firstblock
of the associated transaction. The one outlier is
xlog_recover_process_intents(), which simply passes a dummy value
because a valid pointer is required. This firstblock variable can
simply be removed.
At this point we could remove the xfs_defer_init() firstblock
parameter and initialize ->t_firstblock directly. Even that is not
necessary, however, because ->t_firstblock is automatically
reinitialized in the new transaction on a transaction roll. Since
xfs_defer_init() should never occur more than once on a particular
transaction (since the corresponding finish will roll it), replace
the reinit from xfs_defer_init() with an assert that verifies the
transaction has a NULLFSBLOCK firstblock.
Signed-off-by: Brian Foster <bfoster@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Most callers of xfs_defer_init() immediately attach the dfops
structure to a transaction. Add a transaction parameter to eliminate
much of this boilerplate code. This also helps self-document the
fact that many codepaths now expect a dfops pointer implicitly via
xfs_trans->t_dfops.
Signed-off-by: Brian Foster <bfoster@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
do_mod() is a hold-over from when we have different sizes for file
offsets and and other internal values for 40 bit XFS filesystems.
Hence depending on build flags variables passed to do_mod() could
change size. We no longer support those small format filesystems and
hence everything is of fixed size theses days, even on 32 bit
platforms.
As such, we can convert all the do_mod() callers to platform
optimised modulus operations as defined by linux/math64.h.
Individual conversions depend on the types of variables being used.
Signed-Off-By: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Get rid of the MIN/MAX macros and just use the native min/max macros
directly in the XFS code.
Signed-Off-By: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Brian Foster <bfoster@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Remove the verbose license text from XFS files and replace them
with SPDX tags. This does not change the license of any of the code,
merely refers to the common, up-to-date license files in LICENSES/
This change was mostly scripted. fs/xfs/Makefile and
fs/xfs/libxfs/xfs_fs.h were modified by hand, the rest were detected
and modified by the following command:
for f in `git grep -l "GNU General" fs/xfs/` ; do
echo $f
cat $f | awk -f hdr.awk > $f.new
mv -f $f.new $f
done
And the hdr.awk script that did the modification (including
detecting the difference between GPL-2.0 and GPL-2.0+ licenses)
is as follows:
$ cat hdr.awk
BEGIN {
hdr = 1.0
tag = "GPL-2.0"
str = ""
}
/^ \* This program is free software/ {
hdr = 2.0;
next
}
/any later version./ {
tag = "GPL-2.0+"
next
}
/^ \*\// {
if (hdr > 0.0) {
print "// SPDX-License-Identifier: " tag
print str
print $0
str=""
hdr = 0.0
next
}
print $0
next
}
/^ \* / {
if (hdr > 1.0)
next
if (hdr > 0.0) {
if (str != "")
str = str "\n"
str = str $0
next
}
print $0
next
}
/^ \*/ {
if (hdr > 0.0)
next
print $0
next
}
// {
if (hdr > 0.0) {
if (str != "")
str = str "\n"
str = str $0
next
}
print $0
}
END { }
$
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Explicitly pass the buffer length to xfs_corruption_error() instead of
assuming XFS_CORRUPTION_DUMP_LEN so that we avoid dumping off the end
of the buffer.
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Reviewed-by: Dave Chinner <dchinner@redhat.com>
Long ago the flags argument was used to determine whether to issue warnings
about corruptions, but that's done elsewhere now and the flag is unused
here, so remove it.
Signed-off-by: Eric Sandeen <sandeen@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Today if we run xfs_fsr and crash[1], log replay can fail because
the recovery code tries to instantiate the donor inode from
disk to replay the swapext, but it's been deleted and we get
verifier failures when we try to read the inode off disk with
i_mode == 0.
This fixes both sides: We don't log the swapext change if the
inode has been deleted, and we don't try to recover it either.
[1] or if systemd doesn't cleanly unmount root, as it is wont
to do ...
Signed-off-by: Eric Sandeen <sandeen@redhat.com>
Reviewed-by: Brian Foster <bfoster@redhat.com>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
This is a simple rename, except that xa_ail becomes ail_head.
Signed-off-by: Matthew Wilcox <mawilcox@microsoft.com>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
The memcpy is guarded by a check which is performed a right before we
call xfs_log_dinode_to_disk. At this point we are sure this check will
always be false otherwise we would have errored out. So let's remove
this dead weight.
Signed-off-by: Nikolay Borisov <nborisov@suse.com>
Reviewed-by: Carlos Maiolino <cmaiolino@redhat.com>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
The dmevmask structure member is a dmapi leftover; it's
set here and there but never actually used. Remove it.
Signed-off-by: Eric Sandeen <sandeen@redhat.com>
Reviewed-by: Bill O'Donnell <billodo@redhat.com>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
By splitting the b_fspriv field into two different fields (b_log_item
and b_li_list). It's possible to get rid of an old ABI workaround, by
using the new b_log_item field to store xfs_buf_log_item separated from
the log items attached to the buffer, which will be linked in the new
b_li_list field.
This way, there is no more need to reorder the log items list to place
the buf_log_item at the beginning of the list, simplifying a bit the
logic to handle buffer IO.
This also opens the possibility to change buffer's log items list into a
proper list_head.
b_log_item field is still defined as a void *, because it is still used
by the log buffers to store xlog_in_core structures, and there is no
need to add an extra field on xfs_buf just for xlog_in_core.
Signed-off-by: Carlos Maiolino <cmaiolino@redhat.com>
Reviewed-by: Bill O'Donnell <billodo@redhat.com>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
[darrick: minor style changes]
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Starting with commit 57e734423a ("vsprintf: refactor %pK code out of
pointer"), the behavior of the raw '%p' printk format specifier was
changed to print a 32-bit hash of the pointer value to avoid leaking
kernel pointers into dmesg. For most situations that's good.
This is /undesirable/ behavior when we're trying to debug XFS, however,
so define a PTR_FMT that prints the actual pointer when we're in debug
mode.
Note that %p for tracepoints still prints the raw pointer, so in the
long run we could consider rewriting some of these messages as
tracepoints.
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Reviewed-by: Dave Chinner <dchinner@redhat.com>
Since %p prepends "0x" to the outputted string, we can drop the prefix.
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Reviewed-by: Dave Chinner <dchinner@redhat.com>
Rename xfs_dqcheck to xfs_dquot_verify and make it return an
xfs_failaddr_t like every other structure verifier function.
This enables us to check on-disk quotas in the same way that we check
everything else. Callers are now responsible for logging errors, as
XFS_QMOPT_DOWARN goes away.
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Reviewed-by: Dave Chinner <dchinner@redhat.com>
Replace the current haphazard dir2 shortform verifier callsites with a
centralized verifier function that can be called either with the default
verifier functions or with a custom set. This helps us strengthen
integrity checking while providing us with flexibility for repair tools.
xfs_repair wants this to be able to supply its own verifier functions
when trying to fix possibly corrupt metadata.
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Reviewed-by: Dave Chinner <dchinner@redhat.com>
As part of testing log recovery with dm_log_writes, Amir Goldstein
discovered an error in the deferred ops recovery that lead to corruption
of the filesystem metadata if a reflink+rmap filesystem happened to shut
down midway through a CoW remap:
"This is what happens [after failed log recovery]:
"Phase 1 - find and verify superblock...
"Phase 2 - using internal log
" - zero log...
" - scan filesystem freespace and inode maps...
" - found root inode chunk
"Phase 3 - for each AG...
" - scan (but don't clear) agi unlinked lists...
" - process known inodes and perform inode discovery...
" - agno = 0
"data fork in regular inode 134 claims CoW block 376
"correcting nextents for inode 134
"bad data fork in inode 134
"would have cleared inode 134"
Hou Tao dissected the log contents of exactly such a crash:
"According to the implementation of xfs_defer_finish(), these ops should
be completed in the following sequence:
"Have been done:
"(1) CUI: Oper (160)
"(2) BUI: Oper (161)
"(3) CUD: Oper (194), for CUI Oper (160)
"(4) RUI A: Oper (197), free rmap [0x155, 2, -9]
"Should be done:
"(5) BUD: for BUI Oper (161)
"(6) RUI B: add rmap [0x155, 2, 137]
"(7) RUD: for RUI A
"(8) RUD: for RUI B
"Actually be done by xlog_recover_process_intents()
"(5) BUD: for BUI Oper (161)
"(6) RUI B: add rmap [0x155, 2, 137]
"(7) RUD: for RUI B
"(8) RUD: for RUI A
"So the rmap entry [0x155, 2, -9] for COW should be freed firstly,
then a new rmap entry [0x155, 2, 137] will be added. However, as we can see
from the log record in post_mount.log (generated after umount) and the trace
print, the new rmap entry [0x155, 2, 137] are added firstly, then the rmap
entry [0x155, 2, -9] are freed."
When reconstructing the internal log state from the log items found on
disk, it's required that deferred ops replay in exactly the same order
that they would have had the filesystem not gone down. However,
replaying unfinished deferred ops can create /more/ deferred ops. These
new deferred ops are finished in the wrong order. This causes fs
corruption and replay crashes, so let's create a single defer_ops to
handle the subsequent ops created during replay, then use one single
transaction at the end of log recovery to ensure that everything is
replayed in the same order as they're supposed to be.
Reported-by: Amir Goldstein <amir73il@gmail.com>
Analyzed-by: Hou Tao <houtao1@huawei.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Tested-by: Amir Goldstein <amir73il@gmail.com>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
We already did it in the forward declaration, but not for the function
body itself.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Remove xfs_inode_log_format_t now that xfs_inode_log_format is
explicitly padded and therefore is a real on-disk structure. This
enables xfs/122 to check the size of the structure.
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Reviewed-by: Dave Chinner <dchinner@redhat.com>
It is possible for mkfs to format very small filesystems with too
small of an internal log with respect to the various minimum size
and block count requirements. If this occurs when the log happens to
be smaller than the scan window used for cycle verification and the
scan wraps the end of the log, the start_blk calculation in
xlog_find_head() underflows and leads to an attempt to scan an
invalid range of log blocks. This results in log recovery failure
and a failed mount.
Since there may be filesystems out in the wild with this kind of
geometry, we cannot simply refuse to mount. Instead, cap the scan
window for cycle verification to the size of the physical log. This
ensures that the cycle verification proceeds as expected when the
scan wraps the end of the log.
Reported-by: Zorro Lang <zlang@redhat.com>
Signed-off-by: Brian Foster <bfoster@redhat.com>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
mkfs has a historical problem where it can format very small
filesystems with too small of a physical log. Under certain
conditions, log recovery of an associated filesystem can end up
passing garbage parameter values to some of the cycle and log record
verification functions due to bugs in log recovery not dealing with
such filesystems properly. This results in attempts to read from
bogus/underflowed log block addresses.
Since the buffer read may ultimately succeed, log recovery can
proceed with bogus data and otherwise go off the rails and crash.
One example of this is a negative last_blk being passed to
xlog_find_verify_log_record() causing us to skip the loop, pass a
NULL head pointer to xlog_header_check_mount() and crash.
Improve the xlog buffer verification to address this problem. We
already verify xlog buffer length, so update this mechanism to also
sanity check for a valid log relative block address and otherwise
return an error. Pass a fixed, valid log block address from
xlog_get_bp() since the target address will be validated when the
buffer is read. This ensures that any bogus log block address/length
calculations lead to graceful mount failure rather than risking a
crash or worse if recovery proceeds with bogus data.
Reported-by: Zorro Lang <zlang@redhat.com>
Signed-off-by: Brian Foster <bfoster@redhat.com>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Remove the dead code dealing with the UUID fork format that was never
implemented in Linux (and neither in IRIX as far as I know).
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Fix up all the compiler warnings that have crept in.
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Torn write detection and tail overwrite detection can shift the log
head and tail respectively in the event of CRC mismatch or
corruption errors. Add a high-level log recovery tracepoint to dump
the final log head/tail and make those values easily attainable in
debug/diagnostic situations.
Signed-off-by: Brian Foster <bfoster@redhat.com>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Torn write and tail overwrite detection both trigger only on
-EFSBADCRC errors. While this is the most likely failure scenario
for each condition, -EFSCORRUPTED is still possible in certain cases
depending on what ends up on disk when a torn write or partial tail
overwrite occurs. For example, an invalid log record h_len can lead
to an -EFSCORRUPTED error when running the log recovery CRC pass.
Therefore, update log head and tail verification to trigger the
associated head/tail fixups in the event of -EFSCORRUPTED errors
along with -EFSBADCRC. Also, -EFSCORRUPTED can currently be returned
from xlog_do_recovery_pass() before rhead_blk is initialized if the
first record encountered happens to be corrupted. This leads to an
incorrect 'first_bad' return value. Initialize rhead_blk earlier in
the function to address that problem as well.
Signed-off-by: Brian Foster <bfoster@redhat.com>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
If we consider the case where the tail (T) of the log is pinned long
enough for the head (H) to push and block behind the tail, we can
end up blocked in the following state without enough free space (f)
in the log to satisfy a transaction reservation:
0 phys. log N
[-------HffT---H'--T'---]
The last good record in the log (before H) refers to T. The tail
eventually pushes forward (T') leaving more free space in the log
for writes to H. At this point, suppose space frees up in the log
for the maximum of 8 in-core log buffers to start flushing out to
the log. If this pushes the head from H to H', these next writes
overwrite the previous tail T. This is safe because the items logged
from T to T' have been written back and removed from the AIL.
If the next log writes (H -> H') happen to fail and result in
partial records in the log, the filesystem shuts down having
overwritten T with invalid data. Log recovery correctly locates H on
the subsequent mount, but H still refers to the now corrupted tail
T. This results in log corruption errors and recovery failure.
Since the tail overwrite results from otherwise correct runtime
behavior, it is up to log recovery to try and deal with this
situation. Update log recovery tail verification to run a CRC pass
from the first record past the tail to the head. This facilitates
error detection at T and moves the recovery tail to the first good
record past H' (similar to truncating the head on torn write
detection). If corruption is detected beyond the range possibly
affected by the max number of iclogs, the log is legitimately
corrupted and log recovery failure is expected.
Signed-off-by: Brian Foster <bfoster@redhat.com>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Log tail verification currently only occurs when torn writes are
detected at the head of the log. This was introduced because a
change in the head block due to torn writes can lead to a change in
the tail block (each log record header references the current tail)
and the tail block should be verified before log recovery proceeds.
Tail corruption is possible outside of torn write scenarios,
however. For example, partial log writes can be detected and cleared
during the initial head/tail block discovery process. If the partial
write coincides with a tail overwrite, the log tail is corrupted and
recovery fails.
To facilitate correct handling of log tail overwites, update log
recovery to always perform tail verification. This is necessary to
detect potential tail overwrite conditions when torn writes may not
have occurred. This changes normal (i.e., no torn writes) recovery
behavior slightly to detect and return CRC related errors near the
tail before actual recovery starts.
Signed-off-by: Brian Foster <bfoster@redhat.com>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
The high-level log recovery algorithm consists of two loops that
walk the physical log and process log records from the tail to the
head. The first loop handles the case where the tail is beyond the
head and processes records up to the end of the physical log. The
subsequent loop processes records from the beginning of the physical
log to the head.
Because log records can wrap around the end of the physical log, the
first loop mentioned above must handle this case appropriately.
Records are processed from in-core buffers, which means that this
algorithm must split the reads of such records into two partial
I/Os: 1.) from the beginning of the record to the end of the log and
2.) from the beginning of the log to the end of the record. This is
further complicated by the fact that the log record header and log
record data are read into independent buffers.
The current handling of each buffer correctly splits the reads when
either the header or data starts before the end of the log and wraps
around the end. The data read does not correctly handle the case
where the prior header read wrapped or ends on the physical log end
boundary. blk_no is incremented to or beyond the log end after the
header read to point to the record data, but the split data read
logic triggers, attempts to read from an invalid log block and
ultimately causes log recovery to fail. This can be reproduced
fairly reliably via xfstests tests generic/047 and generic/388 with
large iclog sizes (256k) and small (10M) logs.
If the record header read has pushed beyond the end of the physical
log, the subsequent data read is actually contiguous. Update the
data read logic to detect the case where blk_no has wrapped, mod it
against the log size to read from the correct address and issue one
contiguous read for the log data buffer. The log record is processed
as normal from the buffer(s), the loop exits after the current
iteration and the subsequent loop picks up with the first new record
after the start of the log.
Signed-off-by: Brian Foster <bfoster@redhat.com>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
- Avoid quotacheck deadlocks
- Fix transaction overflows when bunmapping fragmented files
- Refactor directory readahead
- Allow admin to configure if ASSERT is fatal
- Improve transaction usage detail logging during overflows
- Minor cleanups
- Don't leak log items when the log shuts down
- Remove double-underscore typedefs
- Various preparation for online scrubbing
- Introduce new error injection configuration sysfs knobs
- Refactor dq_get_next to use extent map directly
- Fix problems with iterating the page cache for unwritten data
- Implement SEEK_{HOLE,DATA} via iomap
- Refactor XFS to use iomap SEEK_HOLE and SEEK_DATA
- Don't use MAXPATHLEN to check on-disk symlink target lengths
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=/GZI
-----END PGP SIGNATURE-----
Merge tag 'xfs-4.13-merge-5' of git://git.kernel.org/pub/scm/fs/xfs/xfs-linux
Pull XFS updates from Darrick Wong:
"Here are some changes for you for 4.13. For the most part it's fixes
for bugs and deadlock problems, and preparation for online fsck in
some future merge window.
- Avoid quotacheck deadlocks
- Fix transaction overflows when bunmapping fragmented files
- Refactor directory readahead
- Allow admin to configure if ASSERT is fatal
- Improve transaction usage detail logging during overflows
- Minor cleanups
- Don't leak log items when the log shuts down
- Remove double-underscore typedefs
- Various preparation for online scrubbing
- Introduce new error injection configuration sysfs knobs
- Refactor dq_get_next to use extent map directly
- Fix problems with iterating the page cache for unwritten data
- Implement SEEK_{HOLE,DATA} via iomap
- Refactor XFS to use iomap SEEK_HOLE and SEEK_DATA
- Don't use MAXPATHLEN to check on-disk symlink target lengths"
* tag 'xfs-4.13-merge-5' of git://git.kernel.org/pub/scm/fs/xfs/xfs-linux: (48 commits)
xfs: don't crash on unexpected holes in dir/attr btrees
xfs: rename MAXPATHLEN to XFS_SYMLINK_MAXLEN
xfs: fix contiguous dquot chunk iteration livelock
xfs: Switch to iomap for SEEK_HOLE / SEEK_DATA
vfs: Add iomap_seek_hole and iomap_seek_data helpers
vfs: Add page_cache_seek_hole_data helper
xfs: remove a whitespace-only line from xfs_fs_get_nextdqblk
xfs: rewrite xfs_dq_get_next_id using xfs_iext_lookup_extent
xfs: Check for m_errortag initialization in xfs_errortag_test
xfs: grab dquots without taking the ilock
xfs: fix semicolon.cocci warnings
xfs: Don't clear SGID when inheriting ACLs
xfs: free cowblocks and retry on buffered write ENOSPC
xfs: replace log_badcrc_factor knob with error injection tag
xfs: convert drop_writes to use the errortag mechanism
xfs: remove unneeded parameter from XFS_TEST_ERROR
xfs: expose errortag knobs via sysfs
xfs: make errortag a per-mountpoint structure
xfs: free uncommitted transactions during log recovery
xfs: don't allow bmap on rt files
...
Log recovery allocates in-core transaction and member item data
structures on-demand as it processes the on-disk log. Transactions
are allocated on first encounter on-disk and stored in a hash table
structure where they are easily accessible for subsequent lookups.
Transaction items are also allocated on demand and are attached to
the associated transactions.
When a commit record is encountered in the log, the transaction is
committed to the fs and the in-core structures are freed. If a
filesystem crashes or shuts down before all in-core log buffers are
flushed to the log, however, not all transactions may have commit
records in the log. As expected, the modifications in such an
incomplete transaction are not replayed to the fs. The in-core data
structures for the partial transaction are never freed, however,
resulting in a memory leak.
Update xlog_do_recovery_pass() to first correctly initialize the
hash table array so empty lists can be distinguished from populated
lists on function exit. Update xlog_recover_free_trans() to always
remove the transaction from the list prior to freeing the associated
memory. Finally, walk the hash table of transaction lists as the
last step before it goes out of scope and free any transactions that
may remain on the lists. This prevents a memory leak of partial
transactions in the log.
Signed-off-by: Brian Foster <bfoster@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
This is a purely mechanical patch that removes the private
__{u,}int{8,16,32,64}_t typedefs in favor of using the system
{u,}int{8,16,32,64}_t typedefs. This is the sed script used to perform
the transformation and fix the resulting whitespace and indentation
errors:
s/typedef\t__uint8_t/typedef __uint8_t\t/g
s/typedef\t__uint/typedef __uint/g
s/typedef\t__int\([0-9]*\)_t/typedef int\1_t\t/g
s/__uint8_t\t/__uint8_t\t\t/g
s/__uint/uint/g
s/__int\([0-9]*\)_t\t/__int\1_t\t\t/g
s/__int/int/g
/^typedef.*int[0-9]*_t;$/d
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Use the common helper uuid_is_null() and remove the xfs specific
helper uuid_is_nil().
The common helper does not check for the NULL pointer value as
xfs helper did, but xfs code never calls the helper with a pointer
that can be NULL.
Conform comments and warning strings to use the term 'null uuid'
instead of 'nil uuid', because this is the terminology used by
lib/uuid.c and its users. It is also the terminology used in
userspace by libuuid and xfsprogs.
Signed-off-by: Amir Goldstein <amir73il@gmail.com>
[hch: remove now unused uuid.[ch]]
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Brian Foster <bfoster@redhat.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Fix typos and add the following to the scripts/spelling.txt:
intialisation||initialisation
intialised||initialised
intialise||initialise
This commit does not intend to change the British spelling itself.
Link: http://lkml.kernel.org/r/1481573103-11329-18-git-send-email-yamada.masahiro@socionext.com
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Nick Piggin reported that the CRC overhead in an fsync heavy
workload was higher than expected on a Power8 machine. Part of this
was to do with the fact that the power8 CRC implementation is not
efficient for CRC lengths of less than 512 bytes, and so the way we
split the CRCs over the CRC field means a lot of the CRCs are
reduced to being less than than optimal size.
To optimise this, change the CRC update mechanism to zero the CRC
field first, and then compute the CRC in one pass over the buffer
and write the result back into the buffer. We can do this safely
because anything writing a CRC has exclusive access to the buffer
the CRC is being calculated over.
We leave the CRC verify code the same - it still splits the CRC
calculation - because we do not want read-only operations modifying
the underlying buffer. This is because read-only operations may not
have an exclusive access to the buffer guaranteed, and so temporary
modifications could leak out to to other processes accessing the
buffer concurrently.
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Dave Chinner <david@fromorbit.com>
We've missed properly setting the buffer type for
an AGI transaction in 3 spots now, so just move it
into xfs_read_agi() and set it if we are in a transaction
to avoid the problem in the future.
This is similar to how it is done in i.e. the dir3
and attr3 read functions.
Signed-off-by: Eric Sandeen <sandeen@redhat.com>
Reviewed-by: Brian Foster <bfoster@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Dave Chinner <david@fromorbit.com>
xlog_recover_clear_agi_bucket didn't set the
type to XFS_BLFT_AGI_BUF, so we got a warning during log
replay (or an ASSERT on a debug build).
XFS (md0): Unknown buffer type 0!
XFS (md0): _xfs_buf_ioapply: no ops on block 0xaea8802/0x1
Fix this, as was done in f19b872b for 2 other locations
with the same problem.
cc: <stable@vger.kernel.org> # 3.10 to current
Signed-off-by: Eric Sandeen <sandeen@redhat.com>
Reviewed-by: Brian Foster <bfoster@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Dave Chinner <david@fromorbit.com>
Since xfsprogs dropped ushort in favor of unsigned short, do that
here too.
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Reviewed-by: Dave Chinner <dchinner@redhat.com>
Signed-off-by: Dave Chinner <david@fromorbit.com>
Log recovery will iget an inode to replay BUI items and iput the inode
when it's done. Unfortunately, if the inode was unlinked, the iput
will see that i_nlink == 0 and decide to truncate & free the inode,
which prevents us from replaying subsequent BUIs. We can't skip the
BUIs because we have to replay all the redo items to ensure that
atomic operations complete.
Since unlinked inode recovery will reap the inode anyway, we can
safely introduce a new inode flag to indicate that an inode is in this
'unlinked recovery' state and should not be auto-reaped in the
drop_inode path.
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Provide a mechanism for higher levels to create BUI/BUD items, submit
them to the log, and a stub function to deal with recovered BUI items.
These parts will be connected to the rmapbt in a later patch.
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Identify refcountbt blocks in the log correctly so that we can
validate them during log recovery.
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Brian Foster
Darrick J. Wong
Dave Chinner
Eric Sandeen
Matthew Wilcox
Nikolay Borisov
Eric Sandeen
Carlos Maiolino
Christoph Hellwig
Linus Torvalds
Amir Goldstein
Masahiro Yamada
Dave Chinner