Convert the current documentation for the TT flags in proper
kerneldoc and improve it by adding an explanation for each
of the flags.
Signed-off-by: Antonio Quartulli <antonio@open-mesh.com>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
With this patch a node sends IPv4 multicast packets to nodes which
have a BATADV_MCAST_WANT_ALL_IPV4 flag set and IPv6 multicast packets
to nodes which have a BATADV_MCAST_WANT_ALL_IPV6 flag set, too.
Why is this needed? There are scenarios involving bridges where
multicast report snooping and multicast TT announcements are not
sufficient, which would lead to packet loss for some nodes otherwise:
MLDv1 and IGMPv1/IGMPv2 have a suppression mechanism
for multicast listener reports. When we have an MLDv1/IGMPv1/IGMPv2
querier behind a bridge then our snooping bridge is potentially not
going to see any reports even though listeners exist because according
to RFC4541 such reports are only forwarded to multicast routers:
-----------------------------------------------------------
---------------
{Querier}---|Snoop. Switch|----{Listener}
---------------
\ ^
-------
| br0 | < ???
-------
\
_-~---~_
_-~/ ~-_
~ batman-adv \-----{Sender}
\~_ cloud ~/
-~~__-__-~_/
I) MLDv1 Query: {Querier} -> flooded
II) MLDv1 Report: {Listener} -> {Querier}
-> br0 cannot detect the {Listener}
=> Packets from {Sender} need to be forwarded to all
detected listeners and MLDv1/IGMPv1/IGMPv2 queriers.
-----------------------------------------------------------
Note that we do not need to explicitly forward to MLDv2/IGMPv3 queriers,
because these protocols have no report suppression: A bridge has no
trouble detecting MLDv2/IGMPv3 listeners.
Even though we do not support bridges yet we need to provide the
according infrastructure already to not break compatibility later.
Signed-off-by: Linus Lüssing <linus.luessing@web.de>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
With this patch a node may additionally perform the dropping or
unicasting behaviour for a link-local IPv4 and link-local-all-nodes
IPv6 multicast packet, too.
The extra counter and BATADV_MCAST_WANT_ALL_UNSNOOPABLES flag is needed
because with a future bridge snooping support integration a node with a
bridge on top of its soft interface is not able to reliably detect its
multicast listeners for IPv4 link-local and the IPv6
link-local-all-nodes addresses anymore (see RFC4541, section 2.1.2.2
and section 3).
Even though this new flag does make "no difference" now, it'll ensure
a seamless integration of multicast bridge support without needing to
break compatibility later.
Also note, that even with multicast bridge support it won't be possible
to optimize 224.0.0.x and ff02::1 towards nodes with bridges, they will
always receive these ranges.
Signed-off-by: Linus Lüssing <linus.luessing@web.de>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
If the soft interface of a node is not part of a bridge then a node
announces a new multicast TVLV: The existence of this TVLV
signalizes that this node is announcing all of its multicast listeners
via the translation table infrastructure.
Signed-off-by: Linus Lüssing <linus.luessing@web.de>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
A client sending packets which mark matches the value
configured via sysfs has to be identified as isolated using
the TT_CLIENT_ISOLA flag.
The match is mask based, meaning that only bits set in the
mask are compared with those in the mark value.
If the configured mask is equal to 0 no operation is
performed.
Such flag is then advertised within the classic client
announcement mechanism.
Signed-off-by: Antonio Quartulli <antonio@open-mesh.com>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
As suggested by checkpatch, remove all the references to the
FSF address since the kernel already has one reference in
its documentation.
In this way it is easier to update it in case of future
changes.
Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Make struct batadv_tvlv_tt_change a multiple 4 bytes long
to avoid padding on any architecture.
Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Since this is a mac address and always 48 bit, and we can assume that
it is always aligned to 2-byte boundaries, add a pack(2) pragma.
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
struct batadv_icmp_header currently has a size of 17, which
will be padded to 20 on some architectures. Fix this by
unrolling the header into the parent structures.
Moreover keep the ICMP parsing functions as generic as they
are now by using a stub icmp_header struct during packet
parsing.
Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
The size of the batadv_header of 3 is problematic on some architectures
which automatically pad all structures to a 32 bit boundary. To not lose
performance by packing this struct, better embed it into the various
host structures.
Reported-by: Russell King <linux@arm.linux.org.uk>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
The compiler may decide to pad the structure, and then it does not
have the expected size of 46 byte. Fix this by moving it in the
pragma pack(2) part of the code.
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
Instead of handling icmp packets only up to length of icmp_packet_rr,
the code should handle any icmp length size. Therefore the length
truncating is moved to when the packet is actually sent to userspace
(this does not support lengths longer than icmp_packet_rr yet). Longer
packets are forwarded without truncating.
This patch also cleans up some parts where the icmp header struct could
be used instead of other icmp_packet(_rr) structs to make the code more
readable.
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
Flags covered by TT_SYNC_MASK are kept in sync among the
nodes in the network and therefore they have to be
considered while computing the global/local table CRC.
In this way a generic originator is able to understand if
its table contains the correct flags or not.
Bits from 4 to 7 in the TT flags fields are now reserved for
"synchronized" flags only.
This allows future developers to add more flags of this type
without breaking compatibility.
It's important to note that not all the remote TT flags are
synchronised. This comes from the fact that some flags are
used to inject an information once only.
Signed-off-by: Antonio Quartulli <antonio@open-mesh.com>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
This change allows nodes to handle the TT table on a
per-VLAN basis. This is needed because nodes may have to
store only some of the global entries advertised by another
node.
In this scenario such nodes would re-create only a partial
global table and would not be able to compute a correct CRC
anymore.
This patch splits the logic and introduces one CRC per VLAN.
In this way a node fetching only some entries belonging to
some VLANs is still able to compute the needed CRCs and
still check the table correctness.
With this patch the shape of the TVLV-TT is changed too
because now a node needs to advertise all the CRCs of all
the VLANs that it is wired to.
The debug output of the local Translation Table now shows
the CRC along with each entry since there is not a common
value for the entire table anymore.
Signed-off-by: Antonio Quartulli <antonio@open-mesh.com>
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
To make the translation table code VLAN-aware, each entry
must carry the VLAN ID which it belongs to. This patch adds
such attribute to the related TT structures.
Signed-off-by: Antonio Quartulli <antonio@open-mesh.com>
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
the icmp and the icmp_rr packets share the same initial
fields since they use the same code to be processed and
forwarded.
Extract the common fields and put them into a separate
struct so that future ICMP packets can be easily added
without bloating the packet definition.
However, keep the seqno field outside of the newly created
common header because future ICMP types may require a
bigger sequence number space.
This change breaks compatibility due to fields reordering
in the ICMP headers.
Signed-off-by: Antonio Quartulli <antonio@open-mesh.com>
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
Fragments arriving at their destination are buffered for later merge.
Merged packets are passed to the main receive function as had they never
been fragmented.
Fragments are forwarded without merging if the MTU of the outgoing
interface is smaller than the size of the merged packet.
Signed-off-by: Martin Hundebøll <martin@hundeboll.net>
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
Remove the existing fragmentation code before adding the new version
and delete unicast.{h,c}.
batadv_unicast_send_skb() is moved to send.c and renamed to
batadv_send_skb_unicast().
fragmentation entry in sysfs (bat_priv->fragmentation) is kept for use in
the new fragmentation code.
BATADV_UNICAST_FRAG packet type is renamed to BATADV_FRAG for use in the
new fragmentation code.
Signed-off-by: Martin Hundebøll <martin@hundeboll.net>
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
The vis flag is not needed anymore, and since we do a compat bump we
can start with the first bit again
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
As we decreased the struct size from 26 to 24 byte, we can remove
__packed as the compiler will not add any more padding.
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
Reordering the packet type numbers allows us to handle unicast
packets in a general way - even if we don't know the specific packet
type, we can still forward it. There was already code handling
this for a couple of unicast packets, and this is the more
generalized version to do that.
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
This is replaced by a userspace program, we don't need this
functionality to bloat the kernel.
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
Client flags from bit 0 to 7 are sent over the wire.
BATADV_TT_CLIENT_TEMP is a local flag and is not supposed
to be sent to the network. Therefore it has occupy a
higher bit.
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
CRC32C has to be preferred to CRC16 because of its possible
HW native support and because of the reduced collision
probability. With this change the Translation Table
component now uses CRC32C to compute the local and global
table checksum.
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
Instead of generating roaming specific packets the TVLV unicast API is
used to send roaming information.
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
Instead of generating TT specific packets the TVLV unicast API is used
to send translation table data.
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
The translation table meta data (version number, crc checksum, etc)
as well as the translation table diff propgated within OGMs now uses
the newly introduced tvlv infrastructure.
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
Create DAT container to announce DAT capabilities (if enabled).
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
Prior to this patch batman-adv read the advertised uplink bandwidth
from userspace and compressed this information into a single byte
called "gateway class".
Now the download & upload bandwidth information is sent as-is. No
userspace change is necessary since the sysfs API always allowed
to specify a bandwidth.
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
Signed-off-by: Spyros Gasteratos <morfeas3000@gmail.com>
Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
The goal is to provide the infrastructure for sending, receiving and
parsing information 'containers' while preserving backward
compatibility. TVLV (based on the commonly known Type Length Value
technique) was chosen as the format for those containers. Even if a
node does not know the tvlv type of a certain container it can simply
skip the current container and proceed with the next. Past experience
has shown features evolve over time, so a 'version' field was added
right from the start to allow differentiating between feature
variants - hence the name: T(ype) V(ersion) L(ength) V(alue).
This patch introduces the basic TVLV infrastructure:
* register / unregister tvlv containers to be sent with each OGM
(on primary interfaces only)
* register / unregister callback handlers to be called upon
finding the corresponding tvlv type in a tvlv buffer
* unicast tvlv send / receive API calls
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
Signed-off-by: Spyros Gasteratos <morfeas3000@gmail.com>
Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
With this change batman-adv is breaking compatibility with
older versions and it is moving to compat-version 15.
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
Signed-off-by: Martin Hundebøll <martin@hundeboll.net>
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
Add a htonl() in network_coding.c when reading the sequence number
from received ogm_packet, to avoid wrong byte ordering when comparing
with a host value. This bug was introduced in
3ed7ada3f0bbcd058567bc0a8f9729a73eba7db6 ("batman-adv: network coding -
detect coding nodes and remove these after timeout").
Change the type of coded_packet->coded_len from uint16 to __be16 to
avoid wrong assumptions about endianness in later uses. Introduced in
c3289f3650d34b60296000a629c99f2488f7c3dd ("batman-adv: network coding -
code and transmit packets if possible").
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Martin Hundebøll <martin@hundeboll.net>
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
Before adding forward-skbs to the coding buffer, the buffer is searched
for a potential coding opportunity. If one is found, the two packets are
network coded and transmitted right away. If not, the forward-skb is
added to the buffer.
Network coded packets are transmitted with information about the two
receivers and the two coded packets. The first receiver is given by the
MAC header, while the second is given in the payload/bat-header. The
second receiver uses promiscuous mode to receive the packet and check
the second destination.
Signed-off-by: Martin Hundebøll <martin@hundeboll.net>
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
The ETH_P_BATMAN ethertype is now defined kernel-wide. Use it instead
of the private BATADV_ETH_P_BATMAN define.
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
All packet headers in front of an ethernet header have to be completely
divisible by 2 but not by 4 to make the payload after the ethernet header again
4 bytes boundary aligned.
A packing of 2 is necessary to avoid extra padding at the end of the struct
caused by a structure member which is larger than two bytes. Otherwise the
structure would not fulfill the previously mentioned rule to avoid the
misalignment of the payload after the ethernet header. It may also lead to
leakage of information when the padding it not initialized before sending.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
ARP messages are now parsed to make it possible to trigger special actions
depending on their types (snooping).
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
The current unicast packet type does not contain the orig source address. This
patches add a new unicast packet (called UNICAST_4ADDR) which provides two new
fields: the originator source address and the subtype (the type of the data
contained in the packet payload). The former is useful to identify the node
which injected the packet into the network and the latter is useful to avoid
creating new unicast packet types in the future: a macro defining a new subtype
will be enough.
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
Headers which are already perfectly aligned and create a 4 byte boundary
non-ethernet header payload can have the __packed attribute removed. The
__packed attribute doesn't change the appeareance of the packet for these
headers because no extra padding is necessary to align the data members. The
compiler will also create slightly faster code for loads of multi-byte members.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
With the current TT mechanism a new client joining the network is not
immediately able to communicate with other hosts because its MAC address has not
been announced yet. This situation holds until the first OGM containing its
joining event will be spread over the mesh network.
This behaviour can be acceptable in networks where the originator interval is a
small value (e.g. 1sec) but if that value is set to an higher time (e.g. 5secs)
the client could suffer from several malfunctions like DHCP client timeouts,
etc.
This patch adds an early detection mechanism that makes nodes in the network
able to recognise "not yet announced clients" by means of the broadcast packets
they emitted on connection (e.g. ARP or DHCP request). The added client will
then be confirmed upon receiving the OGM claiming it or purged if such OGM
is not received within a fixed amount of time.
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
for consistency reasons within the code and with the documentation,
we should always call it "claim" and "unclaim".
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
batman-adv doesn't follow the style for multiline comments that David S. Miller
prefers. All comments should be reformatted to follow this consistent style to
make the code slightly more readable.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
just keep it net-endian all along
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
[lindner_marek@yahoo.de: fix checkpatch warnings]
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Antonio Quartulli
Linus Lüssing
Simon Wunderlich
Antonio Quartulli
Martin Hundebøll
Simon Wunderlich
Simon Wunderlich
Antonio Quartulli
Marek Lindner
Sven Eckelmann
Al Viro