This patch adds a ASoC machine driver to support the EVAL-ADAU1X81 board
connected to a Analog Devices BF5XX evaluation board.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
This patch adds a ASoC machine driver to support the EVAL-ADAU1X61 board
connected to a Analog Devices BF5XX evaluation board.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
There are a few known (minor) problems with having the support code for both I2C
and SPI in the same module:
* We need to be extra careful to make sure to not build the driver into the
kernel if one of the subsystems is build as a module (Currently only I2C
can be build as a module).
* The module init path error handling is rather ugly. E.g. what should be
done if either the SPI or the I2C driver fails to register. Most drivers
that implement SPI and I2C in the same module currently fallback to
undefined behavior in that case. Splitting the the driver into two
modules, one for each bus, allows the registration of the other bus drive
to continue without problems if one of them fails.
This patch splits the ADAV80X driver into 3 modules. One core module that
implements the device logic, but is independent of the bus method used. And one
module for SPI and I2C each that registers the drivers and sets up the regmap
struct for the bus.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
There are a few known (minor) problems with having the support code for both I2C
and SPI in the same module:
* We need to be extra careful to make sure to not build the driver into the
kernel if one of the subsystems is build as a module (Currently only I2C
can be build as a module).
* The module init path error handling is rather ugly. E.g. what should be
done if either the SPI or the I2C driver fails to register? Most drivers
that implement SPI and I2C in the same module currently fallback to
undefined behavior in that case. Splitting the the driver into two
modules, one for each bus allows the registration of the other bus driver
to continue without problems if one of them fails.
This patch splits the ssm2602 driver into 3 modules. One core module that
implements the device logic, but is independent of the bus method used. And one
module for SPI and I2C each that registers the drivers and sets up the regmap
struct for the bus.
While we are at it also cleanup the include section of the ssm2602 driver and
remove unneeded includes.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
There are a few known (minor) problems with having the support code for both I2C
and SPI in the same module:
* We need to be extra careful to make sure to not build the driver into the
kernel if one of the subsystems is build as a module (Currently only I2C
can be build as a module).
* The module init path error handling is rather ugly. E.g. what should be
done if either the SPI or the I2C driver fails to register? Most drivers
that implement SPI and I2C in the same module currently fallback to
undefined behavior in that case. Splitting the the driver into two
modules, one for each bus, allows the registration of the other bus driver
to continue without problems if one of them fails.
This patch splits the AD193X driver into 3 modules. One core module that
implements the device logic, but is independent of the bus method used. And one
module for SPI and I2C each that registers the drivers and sets up the regmap
struct for the bus.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
Since the machine driver selects the CODEC driver we need to make sure that the
machine driver is only selectable if the CODEC driver can be build. This avoids
build errors under some configurations (which typically only result from
randconfig).
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
Now that the bf5xx-i2s driver supports TDM mode and all users of the bf5xx-tdm
driver have been switch over to using the bf5xx-i2s driver there is no need to
keep the b5fxx-tdm driver around.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The bf5xx-i2s driver now has support for TDM mode and the bf5xx-tdm driver is
going to be removed soon, so switch the driver over to bf5xx-i2s.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The bf5xx-i2s driver now has support for TDM mode and the bf5xx-tdm driver is
going to be removed soon, so switch the driver over to bf5xx-i2s.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This driver enables i2s mode support on blackfin bf6xx platform.
We reuse bf5xx-i2s-pcm.c as its i2s pcm driver because it's the same
for both bf5xx and bf6xx soc.
Signed-off-by: Scott Jiang <scott.jiang.linux@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The SPORT(Serial Port) module on bf6xx soc has a totally different ip
comparing to bf5xx soc. An individual SPORT module consists of two
independently configurable SPORT halves with identical functionality.
Each SPORT half can be configured for either transmitter or receiver.
Signed-off-by: Scott Jiang <scott.jiang.linux@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Add a machine driver to support the EVAL-ADAU1373 board connected to a
Analog Devices BF5XX evaluation board.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Add a machine driver to support the EVAL-ADAV801 and EVAL-ADAV803 boards
connected to a Analog Devices BF5XX evaluation board.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This board has hardware switches for selecting SPI or I2C, so don't
require I2C for this driver.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Add a machine driver to support the ADAU1701 SigmaDSP processors on
Analog Devices BF5XX evaluation boards.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
While I2S/TDM/AC97 DAI is built-in, others are compiled as modules,
SND_BF5XX_SOC_SPORT will be module, then DAI can't get some symbols.
Except that, SND_BF5XX_AC97 depends on SND_BF5XX_SOC_AC97 too.
Signed-off-by: Barry Song <barry.song@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This codec has been obsoleted by ADI, so add appropriate warnings to the
source tree to dissuade people from using in new designs based on driver
support.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Barry Song <21cnbao@gmail.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Some of the Blackfin options don't directly follow the kconfig options
they depend on, so kconfig is unable to display the proper tree. So sort
the options such they expand/collapse properly.
Signed-off-by: Barry Song <barry.song@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
As discussed, the patch uses the original TDM order without rewriting.
For the match between TDM slot number and audio channel number, a new
API need be added.
Signed-off-by: Barry Song <21cnbao@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The I2S DAI driver for blackfin SPORT, but works in TDM mode.
I2S is not a special case of TDM with only left and right two slots for
SPORT interface. I2S coordinates with TDM in SPORT, but not a part of
TDM. TDM require different hardware configuration with I2S, not only
different slot number. One is "Stereo Serial Operation" mode of SPORT,
the other one is "Multichannel Operation" mode. They are incompatible
at the same time.
Hardware and DMA description and data transfer flow are much different
for I2S and TDM. Merging them as a whole will be very ugly and difficult
to maintain.
So we don't define a new DAI type, but give two DAI instances for standard
I2S and TDM, both in I2S-family DAI type. The TDM instance still uses the
I2S-family DAI type.
Signed-off-by: Barry Song <21cnbao@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The dependency on SND_SOC is already fulfilled in sound/soc/Kconfig,
thus no more need in Kconfig of each sub directory.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Cc: Cliff Cai <cliff.cai@analog.com>
Signed-off-by: Mike Frysinger <vapier.adi@gmail.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: Cliff Cai <cliff.cai@analog.com>
Signed-off-by: Mike Frysinger <vapier.adi@gmail.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch provides a option for users to enable multi-channel function support
in Blackfin ASoC driver. Because Blackfin is without MMU, it is easy for us and
the user to enable this function at compiling stage not dynamically on the fly.
Signed-off-by: Cliff Cai <cliff.cai@analog.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
tweak SPORT range for non-BF54x so we get proper behavior for BF52x parts
Signed-off-by: Mike Frysinger <vapier.adi@gmail.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Cliff Cai <cliff.cai@analog.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Lars-Peter Clausen
Mark Brown
Scott Jiang
Mike Frysinger
Barry Song
Sonic Zhang
Barry Song
Matt LaPlante
Takashi Iwai
Mike Frysinger
Cliff Cai