Граф коммитов

58 Коммитов

Автор SHA1 Сообщение Дата
Thomas Gleixner 09c434b8a0 treewide: Add SPDX license identifier for more missed files
Add SPDX license identifiers to all files which:

 - Have no license information of any form

 - Have MODULE_LICENCE("GPL*") inside which was used in the initial
   scan/conversion to ignore the file

These files fall under the project license, GPL v2 only. The resulting SPDX
license identifier is:

  GPL-2.0-only

Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-05-21 10:50:45 +02:00
David Woodhouse 9bbe60a67b atm: Preserve value of skb->truesize when accounting to vcc
ATM accounts for in-flight TX packets in sk_wmem_alloc of the VCC on
which they are to be sent. But it doesn't take ownership of those
packets from the sock (if any) which originally owned them. They should
remain owned by their actual sender until they've left the box.

There's a hack in pskb_expand_head() to avoid adjusting skb->truesize
for certain skbs, precisely to avoid messing up sk_wmem_alloc
accounting. Ideally that hack would cover the ATM use case too, but it
doesn't — skbs which aren't owned by any sock, for example PPP control
frames, still get their truesize adjusted when the low-level ATM driver
adds headroom.

This has always been an issue, it seems. The truesize of a packet
increases, and sk_wmem_alloc on the VCC goes negative. But this wasn't
for normal traffic, only for control frames. So I think we just got away
with it, and we probably needed to send 2GiB of LCP echo frames before
the misaccounting would ever have caused a problem and caused
atm_may_send() to start refusing packets.

Commit 14afee4b60 ("net: convert sock.sk_wmem_alloc from atomic_t to
refcount_t") did exactly what it was intended to do, and turned this
mostly-theoretical problem into a real one, causing PPPoATM to fail
immediately as sk_wmem_alloc underflows and atm_may_send() *immediately*
starts refusing to allow new packets.

The least intrusive solution to this problem is to stash the value of
skb->truesize that was accounted to the VCC, in a new member of the
ATM_SKB(skb) structure. Then in atm_pop_raw() subtract precisely that
value instead of the then-current value of skb->truesize.

Fixes: 158f323b98 ("net: adjust skb->truesize in pskb_expand_head()")
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Tested-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
2018-06-17 08:27:01 +09:00
Kees Cook 6da2ec5605 treewide: kmalloc() -> kmalloc_array()
The kmalloc() function has a 2-factor argument form, kmalloc_array(). This
patch replaces cases of:

        kmalloc(a * b, gfp)

with:
        kmalloc_array(a * b, gfp)

as well as handling cases of:

        kmalloc(a * b * c, gfp)

with:

        kmalloc(array3_size(a, b, c), gfp)

as it's slightly less ugly than:

        kmalloc_array(array_size(a, b), c, gfp)

This does, however, attempt to ignore constant size factors like:

        kmalloc(4 * 1024, gfp)

though any constants defined via macros get caught up in the conversion.

Any factors with a sizeof() of "unsigned char", "char", and "u8" were
dropped, since they're redundant.

The tools/ directory was manually excluded, since it has its own
implementation of kmalloc().

The Coccinelle script used for this was:

// Fix redundant parens around sizeof().
@@
type TYPE;
expression THING, E;
@@

(
  kmalloc(
-	(sizeof(TYPE)) * E
+	sizeof(TYPE) * E
  , ...)
|
  kmalloc(
-	(sizeof(THING)) * E
+	sizeof(THING) * E
  , ...)
)

// Drop single-byte sizes and redundant parens.
@@
expression COUNT;
typedef u8;
typedef __u8;
@@

(
  kmalloc(
-	sizeof(u8) * (COUNT)
+	COUNT
  , ...)
|
  kmalloc(
-	sizeof(__u8) * (COUNT)
+	COUNT
  , ...)
|
  kmalloc(
-	sizeof(char) * (COUNT)
+	COUNT
  , ...)
|
  kmalloc(
-	sizeof(unsigned char) * (COUNT)
+	COUNT
  , ...)
|
  kmalloc(
-	sizeof(u8) * COUNT
+	COUNT
  , ...)
|
  kmalloc(
-	sizeof(__u8) * COUNT
+	COUNT
  , ...)
|
  kmalloc(
-	sizeof(char) * COUNT
+	COUNT
  , ...)
|
  kmalloc(
-	sizeof(unsigned char) * COUNT
+	COUNT
  , ...)
)

// 2-factor product with sizeof(type/expression) and identifier or constant.
@@
type TYPE;
expression THING;
identifier COUNT_ID;
constant COUNT_CONST;
@@

(
- kmalloc
+ kmalloc_array
  (
-	sizeof(TYPE) * (COUNT_ID)
+	COUNT_ID, sizeof(TYPE)
  , ...)
|
- kmalloc
+ kmalloc_array
  (
-	sizeof(TYPE) * COUNT_ID
+	COUNT_ID, sizeof(TYPE)
  , ...)
|
- kmalloc
+ kmalloc_array
  (
-	sizeof(TYPE) * (COUNT_CONST)
+	COUNT_CONST, sizeof(TYPE)
  , ...)
|
- kmalloc
+ kmalloc_array
  (
-	sizeof(TYPE) * COUNT_CONST
+	COUNT_CONST, sizeof(TYPE)
  , ...)
|
- kmalloc
+ kmalloc_array
  (
-	sizeof(THING) * (COUNT_ID)
+	COUNT_ID, sizeof(THING)
  , ...)
|
- kmalloc
+ kmalloc_array
  (
-	sizeof(THING) * COUNT_ID
+	COUNT_ID, sizeof(THING)
  , ...)
|
- kmalloc
+ kmalloc_array
  (
-	sizeof(THING) * (COUNT_CONST)
+	COUNT_CONST, sizeof(THING)
  , ...)
|
- kmalloc
+ kmalloc_array
  (
-	sizeof(THING) * COUNT_CONST
+	COUNT_CONST, sizeof(THING)
  , ...)
)

// 2-factor product, only identifiers.
@@
identifier SIZE, COUNT;
@@

- kmalloc
+ kmalloc_array
  (
-	SIZE * COUNT
+	COUNT, SIZE
  , ...)

// 3-factor product with 1 sizeof(type) or sizeof(expression), with
// redundant parens removed.
@@
expression THING;
identifier STRIDE, COUNT;
type TYPE;
@@

(
  kmalloc(
-	sizeof(TYPE) * (COUNT) * (STRIDE)
+	array3_size(COUNT, STRIDE, sizeof(TYPE))
  , ...)
|
  kmalloc(
-	sizeof(TYPE) * (COUNT) * STRIDE
+	array3_size(COUNT, STRIDE, sizeof(TYPE))
  , ...)
|
  kmalloc(
-	sizeof(TYPE) * COUNT * (STRIDE)
+	array3_size(COUNT, STRIDE, sizeof(TYPE))
  , ...)
|
  kmalloc(
-	sizeof(TYPE) * COUNT * STRIDE
+	array3_size(COUNT, STRIDE, sizeof(TYPE))
  , ...)
|
  kmalloc(
-	sizeof(THING) * (COUNT) * (STRIDE)
+	array3_size(COUNT, STRIDE, sizeof(THING))
  , ...)
|
  kmalloc(
-	sizeof(THING) * (COUNT) * STRIDE
+	array3_size(COUNT, STRIDE, sizeof(THING))
  , ...)
|
  kmalloc(
-	sizeof(THING) * COUNT * (STRIDE)
+	array3_size(COUNT, STRIDE, sizeof(THING))
  , ...)
|
  kmalloc(
-	sizeof(THING) * COUNT * STRIDE
+	array3_size(COUNT, STRIDE, sizeof(THING))
  , ...)
)

// 3-factor product with 2 sizeof(variable), with redundant parens removed.
@@
expression THING1, THING2;
identifier COUNT;
type TYPE1, TYPE2;
@@

(
  kmalloc(
-	sizeof(TYPE1) * sizeof(TYPE2) * COUNT
+	array3_size(COUNT, sizeof(TYPE1), sizeof(TYPE2))
  , ...)
|
  kmalloc(
-	sizeof(TYPE1) * sizeof(THING2) * (COUNT)
+	array3_size(COUNT, sizeof(TYPE1), sizeof(TYPE2))
  , ...)
|
  kmalloc(
-	sizeof(THING1) * sizeof(THING2) * COUNT
+	array3_size(COUNT, sizeof(THING1), sizeof(THING2))
  , ...)
|
  kmalloc(
-	sizeof(THING1) * sizeof(THING2) * (COUNT)
+	array3_size(COUNT, sizeof(THING1), sizeof(THING2))
  , ...)
|
  kmalloc(
-	sizeof(TYPE1) * sizeof(THING2) * COUNT
+	array3_size(COUNT, sizeof(TYPE1), sizeof(THING2))
  , ...)
|
  kmalloc(
-	sizeof(TYPE1) * sizeof(THING2) * (COUNT)
+	array3_size(COUNT, sizeof(TYPE1), sizeof(THING2))
  , ...)
)

// 3-factor product, only identifiers, with redundant parens removed.
@@
identifier STRIDE, SIZE, COUNT;
@@

(
  kmalloc(
-	(COUNT) * STRIDE * SIZE
+	array3_size(COUNT, STRIDE, SIZE)
  , ...)
|
  kmalloc(
-	COUNT * (STRIDE) * SIZE
+	array3_size(COUNT, STRIDE, SIZE)
  , ...)
|
  kmalloc(
-	COUNT * STRIDE * (SIZE)
+	array3_size(COUNT, STRIDE, SIZE)
  , ...)
|
  kmalloc(
-	(COUNT) * (STRIDE) * SIZE
+	array3_size(COUNT, STRIDE, SIZE)
  , ...)
|
  kmalloc(
-	COUNT * (STRIDE) * (SIZE)
+	array3_size(COUNT, STRIDE, SIZE)
  , ...)
|
  kmalloc(
-	(COUNT) * STRIDE * (SIZE)
+	array3_size(COUNT, STRIDE, SIZE)
  , ...)
|
  kmalloc(
-	(COUNT) * (STRIDE) * (SIZE)
+	array3_size(COUNT, STRIDE, SIZE)
  , ...)
|
  kmalloc(
-	COUNT * STRIDE * SIZE
+	array3_size(COUNT, STRIDE, SIZE)
  , ...)
)

// Any remaining multi-factor products, first at least 3-factor products,
// when they're not all constants...
@@
expression E1, E2, E3;
constant C1, C2, C3;
@@

(
  kmalloc(C1 * C2 * C3, ...)
|
  kmalloc(
-	(E1) * E2 * E3
+	array3_size(E1, E2, E3)
  , ...)
|
  kmalloc(
-	(E1) * (E2) * E3
+	array3_size(E1, E2, E3)
  , ...)
|
  kmalloc(
-	(E1) * (E2) * (E3)
+	array3_size(E1, E2, E3)
  , ...)
|
  kmalloc(
-	E1 * E2 * E3
+	array3_size(E1, E2, E3)
  , ...)
)

// And then all remaining 2 factors products when they're not all constants,
// keeping sizeof() as the second factor argument.
@@
expression THING, E1, E2;
type TYPE;
constant C1, C2, C3;
@@

(
  kmalloc(sizeof(THING) * C2, ...)
|
  kmalloc(sizeof(TYPE) * C2, ...)
|
  kmalloc(C1 * C2 * C3, ...)
|
  kmalloc(C1 * C2, ...)
|
- kmalloc
+ kmalloc_array
  (
-	sizeof(TYPE) * (E2)
+	E2, sizeof(TYPE)
  , ...)
|
- kmalloc
+ kmalloc_array
  (
-	sizeof(TYPE) * E2
+	E2, sizeof(TYPE)
  , ...)
|
- kmalloc
+ kmalloc_array
  (
-	sizeof(THING) * (E2)
+	E2, sizeof(THING)
  , ...)
|
- kmalloc
+ kmalloc_array
  (
-	sizeof(THING) * E2
+	E2, sizeof(THING)
  , ...)
|
- kmalloc
+ kmalloc_array
  (
-	(E1) * E2
+	E1, E2
  , ...)
|
- kmalloc
+ kmalloc_array
  (
-	(E1) * (E2)
+	E1, E2
  , ...)
|
- kmalloc
+ kmalloc_array
  (
-	E1 * E2
+	E1, E2
  , ...)
)

Signed-off-by: Kees Cook <keescook@chromium.org>
2018-06-12 16:19:22 -07:00
Tina Ruchandani d750dbdc07 atm: mpoa: remove 32-bit timekeeping
net/atm/mpoa_* files use 'struct timeval' to store event
timestamps. struct timeval uses a 32-bit seconds field which will
overflow in the year 2038 and beyond. Morever, the timestamps are being
compared only to get seconds elapsed, so struct timeval which stores
a seconds and microseconds field is an overkill. This patch replaces
the use of struct timeval with time64_t to store a 64-bit seconds field.

Signed-off-by: Tina Ruchandani <ruchandani.tina@gmail.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
2017-11-30 09:26:32 -05:00
Kees Cook 1e9aa74ecd net/atm/mpc: Avoid open-coded assignment of timer callback function
Instead of a single function assignment, just fold this into DEFINE_TIMER().

Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Kees Cook <keescook@chromium.org>
2017-11-21 15:46:44 -08:00
Linus Torvalds 5bbcc0f595 Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next
Pull networking updates from David Miller:
 "Highlights:

   1) Maintain the TCP retransmit queue using an rbtree, with 1GB
      windows at 100Gb this really has become necessary. From Eric
      Dumazet.

   2) Multi-program support for cgroup+bpf, from Alexei Starovoitov.

   3) Perform broadcast flooding in hardware in mv88e6xxx, from Andrew
      Lunn.

   4) Add meter action support to openvswitch, from Andy Zhou.

   5) Add a data meta pointer for BPF accessible packets, from Daniel
      Borkmann.

   6) Namespace-ify almost all TCP sysctl knobs, from Eric Dumazet.

   7) Turn on Broadcom Tags in b53 driver, from Florian Fainelli.

   8) More work to move the RTNL mutex down, from Florian Westphal.

   9) Add 'bpftool' utility, to help with bpf program introspection.
      From Jakub Kicinski.

  10) Add new 'cpumap' type for XDP_REDIRECT action, from Jesper
      Dangaard Brouer.

  11) Support 'blocks' of transformations in the packet scheduler which
      can span multiple network devices, from Jiri Pirko.

  12) TC flower offload support in cxgb4, from Kumar Sanghvi.

  13) Priority based stream scheduler for SCTP, from Marcelo Ricardo
      Leitner.

  14) Thunderbolt networking driver, from Amir Levy and Mika Westerberg.

  15) Add RED qdisc offloadability, and use it in mlxsw driver. From
      Nogah Frankel.

  16) eBPF based device controller for cgroup v2, from Roman Gushchin.

  17) Add some fundamental tracepoints for TCP, from Song Liu.

  18) Remove garbage collection from ipv6 route layer, this is a
      significant accomplishment. From Wei Wang.

  19) Add multicast route offload support to mlxsw, from Yotam Gigi"

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (2177 commits)
  tcp: highest_sack fix
  geneve: fix fill_info when link down
  bpf: fix lockdep splat
  net: cdc_ncm: GetNtbFormat endian fix
  openvswitch: meter: fix NULL pointer dereference in ovs_meter_cmd_reply_start
  netem: remove unnecessary 64 bit modulus
  netem: use 64 bit divide by rate
  tcp: Namespace-ify sysctl_tcp_default_congestion_control
  net: Protect iterations over net::fib_notifier_ops in fib_seq_sum()
  ipv6: set all.accept_dad to 0 by default
  uapi: fix linux/tls.h userspace compilation error
  usbnet: ipheth: prevent TX queue timeouts when device not ready
  vhost_net: conditionally enable tx polling
  uapi: fix linux/rxrpc.h userspace compilation errors
  net: stmmac: fix LPI transitioning for dwmac4
  atm: horizon: Fix irq release error
  net-sysfs: trigger netlink notification on ifalias change via sysfs
  openvswitch: Using kfree_rcu() to simplify the code
  openvswitch: Make local function ovs_nsh_key_attr_size() static
  openvswitch: Fix return value check in ovs_meter_cmd_features()
  ...
2017-11-15 11:56:19 -08:00
Kees Cook 5c658e19a7 net: atm/mpc: Stop using open-coded timer .data field
In preparation for unconditionally passing the struct timer_list pointer to
all timer callbacks, switch to using an explicit static variable to hold
additional expiration details.

Cc: "David S. Miller" <davem@davemloft.net>
Cc: Bhumika Goyal <bhumirks@gmail.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Alexey Dobriyan <adobriyan@gmail.com>
Cc: "Reshetova, Elena" <elena.reshetova@intel.com>
Cc: netdev@vger.kernel.org
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2017-10-25 13:07:37 +09:00
Kees Cook ba42179350 net: atm: Convert timers to use timer_setup()
In preparation for unconditionally passing the struct timer_list pointer to
all timer callbacks, switch to using the new timer_setup() and from_timer()
to pass the timer pointer explicitly. Also drops a redundant initialization
that is already set up by DEFINE_TIMER.

Cc: "David S. Miller" <davem@davemloft.net>
Cc: Hans Liljestrand <ishkamiel@gmail.com>
Cc: "Reshetova, Elena" <elena.reshetova@intel.com>
Cc: Bhumika Goyal <bhumirks@gmail.com>
Cc: Johannes Berg <johannes.berg@intel.com>
Cc: Roopa Prabhu <roopa@cumulusnetworks.com>
Cc: Augusto Mecking Caringi <augustocaringi@gmail.com>
Cc: Jarod Wilson <jarod@redhat.com>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Alexey Dobriyan <adobriyan@gmail.com>
Cc: netdev@vger.kernel.org
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2017-10-18 12:40:27 +01:00
Kees Cook 1d27e3e225 timer: Remove expires and data arguments from DEFINE_TIMER
Drop the arguments from the macro and adjust all callers with the
following script:

  perl -pi -e 's/DEFINE_TIMER\((.*), 0, 0\);/DEFINE_TIMER($1);/g;' \
    $(git grep DEFINE_TIMER | cut -d: -f1 | sort -u | grep -v timer.h)

Signed-off-by: Kees Cook <keescook@chromium.org>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org> # for m68k parts
Acked-by: Guenter Roeck <linux@roeck-us.net> # for watchdog parts
Acked-by: David S. Miller <davem@davemloft.net> # for networking parts
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Kalle Valo <kvalo@codeaurora.org> # for wireless parts
Acked-by: Arnd Bergmann <arnd@arndb.de>
Cc: linux-mips@linux-mips.org
Cc: Petr Mladek <pmladek@suse.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Lai Jiangshan <jiangshanlai@gmail.com>
Cc: Sebastian Reichel <sre@kernel.org>
Cc: Kalle Valo <kvalo@qca.qualcomm.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: linux1394-devel@lists.sourceforge.net
Cc: Chris Metcalf <cmetcalf@mellanox.com>
Cc: linux-s390@vger.kernel.org
Cc: linux-wireless@vger.kernel.org
Cc: "James E.J. Bottomley" <jejb@linux.vnet.ibm.com>
Cc: Wim Van Sebroeck <wim@iguana.be>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Ursula Braun <ubraun@linux.vnet.ibm.com>
Cc: Viresh Kumar <viresh.kumar@linaro.org>
Cc: Harish Patil <harish.patil@cavium.com>
Cc: Stephen Boyd <sboyd@codeaurora.org>
Cc: Michael Reed <mdr@sgi.com>
Cc: Manish Chopra <manish.chopra@cavium.com>
Cc: Len Brown <len.brown@intel.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: linux-pm@vger.kernel.org
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Tejun Heo <tj@kernel.org>
Cc: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Cc: John Stultz <john.stultz@linaro.org>
Cc: Mark Gross <mark.gross@intel.com>
Cc: linux-watchdog@vger.kernel.org
Cc: linux-scsi@vger.kernel.org
Cc: "Martin K. Petersen" <martin.petersen@oracle.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: "Rafael J. Wysocki" <rjw@rjwysocki.net>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Stefan Richter <stefanr@s5r6.in-berlin.de>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: netdev@vger.kernel.org
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: linuxppc-dev@lists.ozlabs.org
Cc: Sudip Mukherjee <sudipm.mukherjee@gmail.com>
Link: https://lkml.kernel.org/r/1507159627-127660-11-git-send-email-keescook@chromium.org
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
2017-10-05 15:01:20 +02:00
Bhumika Goyal 800bb47e71 net: atm: make atmdev_ops const
Make these const as they are only stored in the ops field of a atm_dev
structure, which is const.
Done using Coccinelle.

Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2017-08-09 22:43:50 -07:00
Reshetova, Elena 14afee4b60 net: convert sock.sk_wmem_alloc from atomic_t to refcount_t
refcount_t type and corresponding API should be
used instead of atomic_t when the variable is used as
a reference counter. This allows to avoid accidental
refcounter overflows that might lead to use-after-free
situations.

Signed-off-by: Elena Reshetova <elena.reshetova@intel.com>
Signed-off-by: Hans Liljestrand <ishkamiel@gmail.com>
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: David Windsor <dwindsor@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2017-07-01 07:39:08 -07:00
Alexey Dobriyan 5b5e0928f7 lib/vsprintf.c: remove %Z support
Now that %z is standartised in C99 there is no reason to support %Z.
Unlike %L it doesn't even make format strings smaller.

Use BUILD_BUG_ON in a couple ATM drivers.

In case anyone didn't notice lib/vsprintf.o is about half of SLUB which
is in my opinion is quite an achievement.  Hopefully this patch inspires
someone else to trim vsprintf.c more.

Link: http://lkml.kernel.org/r/20170103230126.GA30170@avx2
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Cc: Andy Shevchenko <andy.shevchenko@gmail.com>
Cc: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2017-02-27 18:43:47 -08:00
Colin Ian King 0d135e4f26 net: atm: remove redundant null pointer check on dev->name
dev->name is a char array of IFNAMSIZ elements, hence can never be
null, so the null pointer check is redundant. Remove it.

Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2016-08-18 21:03:48 -07:00
David S. Miller fa2dbdc253 net: Pass a "more" indication down into netdev_start_xmit() code paths.
For now it will always be false.

Signed-off-by: David S. Miller <davem@davemloft.net>
2014-09-01 17:39:55 -07:00
David S. Miller 4798248e4e net: Add ops->ndo_xmit_flush()
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-08-24 23:02:45 -07:00
David S. Miller 676d23690f net: Fix use after free by removing length arg from sk_data_ready callbacks.
Several spots in the kernel perform a sequence like:

	skb_queue_tail(&sk->s_receive_queue, skb);
	sk->sk_data_ready(sk, skb->len);

But at the moment we place the SKB onto the socket receive queue it
can be consumed and freed up.  So this skb->len access is potentially
to freed up memory.

Furthermore, the skb->len can be modified by the consumer so it is
possible that the value isn't accurate.

And finally, no actual implementation of this callback actually uses
the length argument.  And since nobody actually cared about it's
value, lots of call sites pass arbitrary values in such as '0' and
even '1'.

So just remove the length argument from the callback, that way there
is no confusion whatsoever and all of these use-after-free cases get
fixed as a side effect.

Based upon a patch by Eric Dumazet and his suggestion to audit this
issue tree-wide.

Signed-off-by: David S. Miller <davem@davemloft.net>
2014-04-11 16:15:36 -04:00
Julia Lawall 84275593ac atm: replace del_timer by del_timer_sync
Use del_timer_sync to ensure that the timer is stopped on all CPUs before
the driver exists.

This change was suggested by Thomas Gleixner.

The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)

// <smpl>
@r@
declarer name module_exit;
identifier ex;
@@

module_exit(ex);

@@
identifier r.ex;
@@

ex(...) {
  <...
- del_timer
+ del_timer_sync
    (...)
  ...>
}
// </smpl>

Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-03-27 15:28:06 -04:00
Joe Perches 116e853f7f atm: Use ether_addr_copy
Use ether_addr_copy instead of memcpy(a, b, ETH_ALEN) to
save some cycles on arm and powerpc.

Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-01-21 18:13:04 -08:00
Jiri Pirko 351638e7de net: pass info struct via netdevice notifier
So far, only net_device * could be passed along with netdevice notifier
event. This patch provides a possibility to pass custom structure
able to provide info that event listener needs to know.

Signed-off-by: Jiri Pirko <jiri@resnulli.us>

v2->v3: fix typo on simeth
	shortened dev_getter
	shortened notifier_info struct name
v1->v2: fix notifier_call parameter in call_netdevice_notifier()
Signed-off-by: David S. Miller <davem@davemloft.net>
2013-05-28 13:11:01 -07:00
Joe Perches 150238ebb4 atm: Convert compare_ether_addr to ether_addr_equal
Use the new bool function ether_addr_equal to add
some clarity and reduce the likelihood for misuse
of compare_ether_addr for sorting.

Done via cocci script:

$ cat compare_ether_addr.cocci
@@
expression a,b;
@@
-	!compare_ether_addr(a, b)
+	ether_addr_equal(a, b)

@@
expression a,b;
@@
-	compare_ether_addr(a, b)
+	!ether_addr_equal(a, b)

@@
expression a,b;
@@
-	!ether_addr_equal(a, b) == 0
+	ether_addr_equal(a, b)

@@
expression a,b;
@@
-	!ether_addr_equal(a, b) != 0
+	!ether_addr_equal(a, b)

@@
expression a,b;
@@
-	ether_addr_equal(a, b) == 0
+	!ether_addr_equal(a, b)

@@
expression a,b;
@@
-	ether_addr_equal(a, b) != 0
+	ether_addr_equal(a, b)

@@
expression a,b;
@@
-	!!ether_addr_equal(a, b)
+	ether_addr_equal(a, b)

Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2012-05-09 20:49:17 -04:00
Joe Perches ea11073387 net: Remove casts of void *
Unnecessary casts of void * clutter the code.

These are the remainder casts after several specific
patches to remove netdev_priv and dev_priv.

Done via coccinelle script:

$ cat cast_void_pointer.cocci
@@
type T;
T *pt;
void *pv;
@@

- pt = (T *)pv;
+ pt = pv;

Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Paul Moore <paul.moore@hp.com>
Signed-off-by: David S. Miller <davem@conan.davemloft.net>
2011-06-16 23:19:27 -04:00
Michal Marek 36a9f77e50 atm: Drop __TIME__ usage
The kernel already prints its build timestamp during boot, no need to
repeat it in random drivers and produce different object files each
time.

Acked-by: David S. Miller <davem@davemloft.net>
Cc: netdev@vger.kernel.org
Signed-off-by: Michal Marek <mmarek@suse.cz>
2011-05-26 09:46:47 +02:00
Shan Wei 4c306a9291 net: kill unused macros
These macros never be used, so remove them.

Signed-off-by: Shan Wei <shanwei@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-12-19 21:59:35 -08:00
Jiri Slaby 5518b29f22 ATM: mpc, fix use after free
Stanse found that mpc_push frees skb and then it dereferences it. It
is a typo, new_skb should be dereferenced there.

Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-10-11 11:05:42 -07:00
Joe Perches 3fa21e07e6 net: Remove unnecessary returns from void function()s
This patch removes from net/ (but not any netfilter files)
all the unnecessary return; statements that precede the
last closing brace of void functions.

It does not remove the returns that are immediately
preceded by a label as gcc doesn't like that.

Done via:
$ grep -rP --include=*.[ch] -l "return;\n}" net/ | \
  xargs perl -i -e 'local $/ ; while (<>) { s/\n[ \t\n]+return;\n}/\n}/g; print; }'

Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-05-17 23:23:14 -07:00
Tejun Heo 5a0e3ad6af include cleanup: Update gfp.h and slab.h includes to prepare for breaking implicit slab.h inclusion from percpu.h
percpu.h is included by sched.h and module.h and thus ends up being
included when building most .c files.  percpu.h includes slab.h which
in turn includes gfp.h making everything defined by the two files
universally available and complicating inclusion dependencies.

percpu.h -> slab.h dependency is about to be removed.  Prepare for
this change by updating users of gfp and slab facilities include those
headers directly instead of assuming availability.  As this conversion
needs to touch large number of source files, the following script is
used as the basis of conversion.

  http://userweb.kernel.org/~tj/misc/slabh-sweep.py

The script does the followings.

* Scan files for gfp and slab usages and update includes such that
  only the necessary includes are there.  ie. if only gfp is used,
  gfp.h, if slab is used, slab.h.

* When the script inserts a new include, it looks at the include
  blocks and try to put the new include such that its order conforms
  to its surrounding.  It's put in the include block which contains
  core kernel includes, in the same order that the rest are ordered -
  alphabetical, Christmas tree, rev-Xmas-tree or at the end if there
  doesn't seem to be any matching order.

* If the script can't find a place to put a new include (mostly
  because the file doesn't have fitting include block), it prints out
  an error message indicating which .h file needs to be added to the
  file.

The conversion was done in the following steps.

1. The initial automatic conversion of all .c files updated slightly
   over 4000 files, deleting around 700 includes and adding ~480 gfp.h
   and ~3000 slab.h inclusions.  The script emitted errors for ~400
   files.

2. Each error was manually checked.  Some didn't need the inclusion,
   some needed manual addition while adding it to implementation .h or
   embedding .c file was more appropriate for others.  This step added
   inclusions to around 150 files.

3. The script was run again and the output was compared to the edits
   from #2 to make sure no file was left behind.

4. Several build tests were done and a couple of problems were fixed.
   e.g. lib/decompress_*.c used malloc/free() wrappers around slab
   APIs requiring slab.h to be added manually.

5. The script was run on all .h files but without automatically
   editing them as sprinkling gfp.h and slab.h inclusions around .h
   files could easily lead to inclusion dependency hell.  Most gfp.h
   inclusion directives were ignored as stuff from gfp.h was usually
   wildly available and often used in preprocessor macros.  Each
   slab.h inclusion directive was examined and added manually as
   necessary.

6. percpu.h was updated not to include slab.h.

7. Build test were done on the following configurations and failures
   were fixed.  CONFIG_GCOV_KERNEL was turned off for all tests (as my
   distributed build env didn't work with gcov compiles) and a few
   more options had to be turned off depending on archs to make things
   build (like ipr on powerpc/64 which failed due to missing writeq).

   * x86 and x86_64 UP and SMP allmodconfig and a custom test config.
   * powerpc and powerpc64 SMP allmodconfig
   * sparc and sparc64 SMP allmodconfig
   * ia64 SMP allmodconfig
   * s390 SMP allmodconfig
   * alpha SMP allmodconfig
   * um on x86_64 SMP allmodconfig

8. percpu.h modifications were reverted so that it could be applied as
   a separate patch and serve as bisection point.

Given the fact that I had only a couple of failures from tests on step
6, I'm fairly confident about the coverage of this conversion patch.
If there is a breakage, it's likely to be something in one of the arch
headers which should be easily discoverable easily on most builds of
the specific arch.

Signed-off-by: Tejun Heo <tj@kernel.org>
Guess-its-ok-by: Christoph Lameter <cl@linux-foundation.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>
2010-03-30 22:02:32 +09:00
Joe Perches b50c2ea72a net/atm: Cleanup dprint/ddprintk #defines and uses
Move "mpoa:%s: ", __func__/__FILE__ to #defines
Remove mpoa __func__/__FILE__ from dprintk uses
Add and use #define dprint_cont where appropriate

Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-01-26 21:16:05 -08:00
Joe Perches 5710044073 net/atm/mpc.c: checkpatch cleanups
Convert #include <asm... to #include <linux...
Add printk argument verification to dprintk and ddprintk
Spacing cleanups
Mostly 80 column wrapped.
printk->pr_info and pr_cont
Moved labels to column 1
Move trailing statements to new lines
switch/case cleanups
	remove unnecessary breaks after returns
Remove unnecessary braces around single line statements

Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-01-26 21:16:00 -08:00
Joe Perches 99824461ea net/atm: Convert printk to pr_<level>
Add #define pr_fmt(fmt) KBUILD_MODNAME ":%s: " fmt, __func__
Remove function names from output
Use single line pr_debug instead of broken multiple uses without newline

Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-01-26 21:15:56 -08:00
Stephen Hemminger 3c805a22a3 convert ATM drivers to netdev_tx_t
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-09-01 01:13:10 -07:00
Patrick McHardy ec634fe328 net: convert remaining non-symbolic return values in ndo_start_xmit() functions
This patch converts the remaining occurences of raw return values to their
symbolic counterparts in ndo_start_xmit() functions that were missed by the
previous automatic conversion.

Additionally code that assumed the symbolic value of NETDEV_TX_OK to be zero
is changed to explicitly use NETDEV_TX_OK.

Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-07-05 19:23:38 -07:00
Stephen Hemminger 788dee0a95 atm: convert mpc device to using netdev_ops
This converts the mpc device to using new netdevice_ops.
Compile tested only, needs more than usual review since
device was swaping pointers around etc.

Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Acked-by: Chas Williams <chas@cmf.nrl.navy.mil>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-03-21 19:19:12 -07:00
Wang Chen b74ca3a896 netdevice: Kill netdev->priv
This is the last shoot of this series.
After I removing all directly reference of netdev->priv, I am killing
"priv" of "struct net_device" and fixing relative comments/docs.

Anyone will not be allowed to reference netdev->priv directly.
If you want to reference the memory of private data, use netdev_priv()
instead.
If the private data is not allocted when alloc_netdev(), use
netdev->ml_priv to point that memory after you creating that private
data.

Signed-off-by: Wang Chen <wangchen@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2008-12-08 01:14:16 -08:00
Wang Chen 524ad0a791 netdevice: safe convert to netdev_priv() #part-4
We have some reasons to kill netdev->priv:
1. netdev->priv is equal to netdev_priv().
2. netdev_priv() wraps the calculation of netdev->priv's offset, obviously
   netdev_priv() is more flexible than netdev->priv.
But we cann't kill netdev->priv, because so many drivers reference to it
directly.

This patch is a safe convert for netdev->priv to netdev_priv(netdev).
Since all of the netdev->priv is only for read.
But it is too big to be sent in one mail.
I split it to 4 parts and make every part smaller than 100,000 bytes,
which is max size allowed by vger.

Signed-off-by: Wang Chen <wangchen@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2008-11-12 23:39:10 -08:00
Harvey Harrison 21454aaad3 net: replace NIPQUAD() in net/*/
Using NIPQUAD() with NIPQUAD_FMT, %d.%d.%d.%d or %u.%u.%u.%u
can be replaced with %pI4

Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2008-10-31 00:54:56 -07:00
David Howells cba5cbd155 atm: fix const assignment/discard warnings in the ATM networking driver
Fix const assignment/discard warnings in the ATM networking driver.

The lane2_assoc_ind() function needed its arguments changing to match changes
in the lane2_ops struct (patch 61c33e0129
"atm: use const where reasonable").

Signed-off-by: David Howells <dhowells@redhat.com>
Acked-by: Chas Williams <chas@cmf.nrl.navy.mil>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2008-07-30 16:31:46 -07:00
YOSHIFUJI Hideaki 721499e893 netns: Use net_eq() to compare net-namespaces for optimization.
Without CONFIG_NET_NS, namespace is always &init_net.
Compiler will be able to omit namespace comparisons with this patch.

Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2008-07-19 22:34:43 -07:00
YOSHIFUJI Hideaki c346dca108 [NET] NETNS: Omit net_device->nd_net without CONFIG_NET_NS.
Introduce per-net_device inlines: dev_net(), dev_net_set().
Without CONFIG_NET_NS, no namespace other than &init_net exists.
Let's explicitly define them to help compiler optimizations.

Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
2008-03-26 04:39:53 +09:00
Herbert Xu 1c9b7aa1eb [ATM]: Check IP header validity in mpc_send_packet
Al went through the ip_fast_csum callers and found this piece of code
that did not validate the IP header.  While root crashing the machine
by sending bogus packets through raw or AF_PACKET sockets isn't that
serious, it is still nice to react gracefully.

This patch ensures that the skb has enough data for an IP header and
that the header length field is valid.

Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
2008-01-09 03:51:59 -08:00
Eric W. Biederman 881d966b48 [NET]: Make the device list and device lookups per namespace.
This patch makes most of the generic device layer network
namespace safe.  This patch makes dev_base_head a
network namespace variable, and then it picks up
a few associated variables.  The functions:
dev_getbyhwaddr
dev_getfirsthwbytype
dev_get_by_flags
dev_get_by_name
__dev_get_by_name
dev_get_by_index
__dev_get_by_index
dev_ioctl
dev_ethtool
dev_load
wireless_process_ioctl

were modified to take a network namespace argument, and
deal with it.

vlan_ioctl_set and brioctl_set were modified so their
hooks will receive a network namespace argument.

So basically anthing in the core of the network stack that was
affected to by the change of dev_base was modified to handle
multiple network namespaces.  The rest of the network stack was
simply modified to explicitly use &init_net the initial network
namespace.  This can be fixed when those components of the network
stack are modified to handle multiple network namespaces.

For now the ifindex generator is left global.

Fundametally ifindex numbers are per namespace, or else
we will have corner case problems with migration when
we get that far.

At the same time there are assumptions in the network stack
that the ifindex of a network device won't change.  Making
the ifindex number global seems a good compromise until
the network stack can cope with ifindex changes when
you change namespaces, and the like.

Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2007-10-10 16:49:10 -07:00
Eric W. Biederman e9dc865340 [NET]: Make device event notification network namespace safe
Every user of the network device notifiers is either a protocol
stack or a pseudo device.  If a protocol stack that does not have
support for multiple network namespaces receives an event for a
device that is not in the initial network namespace it quite possibly
can get confused and do the wrong thing.

To avoid problems until all of the protocol stacks are converted
this patch modifies all netdev event handlers to ignore events on
devices that are not in the initial network namespace.

As the rest of the code is made network namespace aware these
checks can be removed.

Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2007-10-10 16:49:09 -07:00
Milind Arun Choudhary 4ef8d0aeaf [NET]: SPIN_LOCK_UNLOCKED cleanup in drivers/atm, net
SPIN_LOCK_UNLOCKED cleanup,use __SPIN_LOCK_UNLOCKED instead

Signed-off-by: Milind Arun Choudhary <milindchoudhary@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2007-04-26 01:37:44 -07:00
Arnaldo Carvalho de Melo 27d7ff46a3 [SK_BUFF]: Introduce skb_copy_to_linear_data{_offset}
To clearly state the intent of copying to linear sk_buffs, _offset being a
overly long variant but interesting for the sake of saving some bytes.

Signed-off-by: Arnaldo Carvalho de Melo <acme@ghostprotocols.net>
2007-04-25 22:28:29 -07:00
Arnaldo Carvalho de Melo eddc9ec53b [SK_BUFF]: Introduce ip_hdr(), remove skb->nh.iph
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2007-04-25 22:25:10 -07:00
Arnaldo Carvalho de Melo c1d2bbe1cd [SK_BUFF]: Introduce skb_reset_network_header(skb)
For the common, open coded 'skb->nh.raw = skb->data' operation, so that we can
later turn skb->nh.raw into a offset, reducing the size of struct sk_buff in
64bit land while possibly keeping it as a pointer on 32bit.

This one touches just the most simple case, next will handle the slightly more
"complex" cases.

Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2007-04-25 22:24:46 -07:00
YOSHIFUJI Hideaki f7d57453d2 [NET] ATM: Fix whitespace errors.
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2007-02-10 23:19:16 -08:00
Arnaldo Carvalho de Melo 2afe37cdff [ATM]: Use kmemdup & kzalloc where applicable
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
2006-12-02 21:30:13 -08:00
Al Viro 30d492da73 [ATM]: Annotations.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
2006-12-02 21:22:55 -08:00
Al Viro b4229934bd [ATM]: use NIPQUAD instead of open-coding it
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
2006-09-28 17:54:00 -07:00
Adrian Bunk 69263bcfb5 [ATM]: proper prototypes in net/atm/mpc.h (and reduce ifdef clutter)
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Chas Williams <chas@cmf.nrl.navy.mil>
Signed-off-by: David S. Miller <davem@davemloft.net>
2006-09-22 15:19:13 -07:00