[ Upstream commit ff91e1b684 ]
The cross-chip notifier boilerplate code meant to check the presence of
ds->ops->port_mrp_add_ring_role before calling it, but checked
ds->ops->port_mrp_add instead, before calling
ds->ops->port_mrp_add_ring_role.
Therefore, a driver which implements one operation but not the other
would trigger a NULL pointer dereference.
There isn't any such driver in DSA yet, so there is no reason to
backport the change. Issue found through code inspection.
Cc: Horatiu Vultur <horatiu.vultur@microchip.com>
Fixes: c595c4330d ("net: dsa: add MRP support")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 92f62485b3 ]
Normally it is expected that the dsa_device_ops :: rcv() method finishes
parsing the DSA tag and consumes it, then never looks at it again.
But commit c0bcf53766 ("net: dsa: ocelot: add hardware timestamping
support for Felix") added support for RX timestamping in a very
unconventional way. On this switch, a partial timestamp is available in
the DSA header, but the driver got away with not parsing that timestamp
right away, but instead delayed that parsing for a little longer:
dsa_switch_rcv():
nskb = cpu_dp->rcv(skb, dev); <------------- not here
-> ocelot_rcv()
...
skb = nskb;
skb_push(skb, ETH_HLEN);
skb->pkt_type = PACKET_HOST;
skb->protocol = eth_type_trans(skb, skb->dev);
...
if (dsa_skb_defer_rx_timestamp(p, skb)) <--- but here
-> felix_rxtstamp()
return 0;
When in felix_rxtstamp(), this driver accounted for the fact that
eth_type_trans() happened in the meanwhile, so it got a hold of the
extraction header again by subtracting (ETH_HLEN + OCELOT_TAG_LEN) bytes
from the current skb->data.
This worked for quite some time but was quite fragile from the very
beginning. Not to mention that having DSA tag parsing split in two
different files, under different folders (net/dsa/tag_ocelot.c vs
drivers/net/dsa/ocelot/felix.c) made it quite non-obvious for patches to
come that they might break this.
Finally, the blamed commit does the following: at the end of
ocelot_rcv(), it checks whether the skb payload contains a VLAN header.
If it does, and this port is under a VLAN-aware bridge, that VLAN ID
might not be correct in the sense that the packet might have suffered
VLAN rewriting due to TCAM rules (VCAP IS1). So we consume the VLAN ID
from the skb payload using __skb_vlan_pop(), and take the classified
VLAN ID from the DSA tag, and construct a hwaccel VLAN tag with the
classified VLAN, and the skb payload is VLAN-untagged.
The big problem is that __skb_vlan_pop() does:
memmove(skb->data + VLAN_HLEN, skb->data, 2 * ETH_ALEN);
__skb_pull(skb, VLAN_HLEN);
aka it moves the Ethernet header 4 bytes to the right, and pulls 4 bytes
from the skb headroom (effectively also moving skb->data, by definition).
So for felix_rxtstamp()'s fragile logic, all bets are off now.
Instead of having the "extraction" pointer point to the DSA header,
it actually points to 4 bytes _inside_ the extraction header.
Corollary, the last 4 bytes of the "extraction" header are in fact 4
stale bytes of the destination MAC address from the Ethernet header,
from prior to the __skb_vlan_pop() movement.
So of course, RX timestamps are completely bogus when the system is
configured in this way.
The fix is actually very simple: just don't structure the code like that.
For better or worse, the DSA PTP timestamping API does not offer a
straightforward way for drivers to present their RX timestamps, but
other drivers (sja1105) have established a simple mechanism to carry
their RX timestamp from dsa_device_ops :: rcv() all the way to
dsa_switch_ops :: port_rxtstamp() and even later. That mechanism is to
simply save the partial timestamp to the skb->cb, and complete it later.
Question: why don't we simply populate the skb's struct
skb_shared_hwtstamps from ocelot_rcv(), and bother with this
complication of propagating the timestamp to felix_rxtstamp()?
Answer: dsa_switch_ops :: port_rxtstamp() answers the question whether
PTP packets need sleepable context to retrieve the full RX timestamp.
Currently felix_rxtstamp() answers "no, thanks" to that question, and
calls ocelot_ptp_gettime64() from softirq atomic context. This is
understandable, since Felix VSC9959 is a PCIe memory-mapped switch, so
hardware access does not require sleeping. But the felix driver is
preparing for the introduction of other switches where hardware access
is over a slow bus like SPI or MDIO:
https://lore.kernel.org/lkml/20210814025003.2449143-1-colin.foster@in-advantage.com/
So I would like to keep this code structure, so the rework needed when
that driver will need PTP support will be minimal (answer "yes, I need
deferred context for this skb's RX timestamp", then the partial
timestamp will still be found in the skb->cb.
Fixes: ea440cd2d9 ("net: dsa: tag_ocelot: use VLAN information from tagging header when available")
Reported-by: Po Liu <po.liu@nxp.com>
Cc: Yangbo Lu <yangbo.lu@nxp.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 232deb3f95 ]
At present, when either of ds->ops->port_fdb_del() or ds->ops->port_mdb_del()
return a non-zero error code, we attempt to save the day and keep the
data structure associated with that switchdev object, as the deletion
procedure did not complete.
However, the way in which we do this is suspicious to the checker in
lib/refcount.c, who thinks it is buggy to increment a refcount that
became zero, and that this is indicative of a use-after-free.
Fixes: 161ca59d39 ("net: dsa: reference count the MDB entries at the cross-chip notifier level")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
When setting up a bridge with stp_state 1, topology changes are not
detected and loops are not blocked. This is because the standard way of
transmitting a packet, based on VLAN IDs redirected by VCAP IS2 to the
right egress port, does not override the port STP state (in the case of
Ocelot switches, that's really the PGID_SRC masks).
To force a packet to be injected into a port that's BLOCKING, we must
send it as a control packet, which means in the case of this tagger to
send it using the manual register injection method. We already do this
for PTP frames, extend the logic to apply to any link-local MAC DA.
Fixes: 7c83a7c539 ("net: dsa: add a second tagger for Ocelot switches based on tag_8021q")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Michael reported that when using the "ocelot-8021q" tagging protocol,
the switch driver module must be manually loaded before the tagging
protocol can be loaded/is available.
This appears to be the same problem described here:
https://lore.kernel.org/netdev/20210908220834.d7gmtnwrorhharna@skbuf/
where due to the fact that DSA tagging protocols make use of symbols
exported by the switch drivers, circular dependencies appear and this
breaks module autoloading.
The ocelot_8021q driver needs the ocelot_can_inject() and
ocelot_port_inject_frame() functions from the switch library. Previously
the wrong approach was taken to solve that dependency: shims were
provided for the case where the ocelot switch library was compiled out,
but that turns out to be insufficient, because the dependency when the
switch lib _is_ compiled is problematic too.
We cannot declare ocelot_can_inject() and ocelot_port_inject_frame() as
static inline functions, because these access I/O functions like
__ocelot_write_ix() which is called by ocelot_write_rix(). Making those
static inline basically means exposing the whole guts of the ocelot
switch library, not ideal...
We already have one tagging protocol driver which calls into the switch
driver during xmit but not using any exported symbol: sja1105_defer_xmit.
We can do the same thing here: create a kthread worker and one work item
per skb, and let the switch driver itself do the register accesses to
send the skb, and then consume it.
Fixes: 0a6f17c6ae ("net: dsa: tag_ocelot_8021q: add support for PTP timestamping")
Reported-by: Michael Walle <michael@walle.cc>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
As explained here:
https://lore.kernel.org/netdev/20210908220834.d7gmtnwrorhharna@skbuf/
DSA tagging protocol drivers cannot depend on symbols exported by switch
drivers, because this creates a circular dependency that breaks module
autoloading.
The tag_ocelot.c file depends on the ocelot_ptp_rew_op() function
exported by the common ocelot switch lib. This function looks at
OCELOT_SKB_CB(skb) and computes how to populate the REW_OP field of the
DSA tag, for PTP timestamping (the command: one-step/two-step, and the
TX timestamp identifier).
None of that requires deep insight into the driver, it is quite
stateless, as it only depends upon the skb->cb. So let's make it a
static inline function and put it in include/linux/dsa/ocelot.h, a
file that despite its name is used by the ocelot switch driver for
populating the injection header too - since commit 40d3f295b5 ("net:
mscc: ocelot: use common tag parsing code with DSA").
With that function declared as static inline, its body is expanded
inside each call site, so the dependency is broken and the DSA tagger
can be built without the switch library, upon which the felix driver
depends.
Fixes: 39e5308b32 ("net: mscc: ocelot: support PTP Sync one-step timestamping")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
It's nice to be able to test a tagging protocol with dsa_loop, but not
at the cost of losing the ability of building the tagging protocol and
switch driver as modules, because as things stand, there is a circular
dependency between the two. Tagging protocol drivers cannot depend on
switch drivers, that is a hard fact.
The reasoning behind the blamed patch was that accessing dp->priv should
first make sure that the structure behind that pointer is what we really
think it is.
Currently the "sja1105" and "sja1110" tagging protocols only operate
with the sja1105 switch driver, just like any other tagging protocol and
switch combination. The only way to mix and match them is by modifying
the code, and this applies to dsa_loop as well (by default that uses
DSA_TAG_PROTO_NONE). So while in principle there is an issue, in
practice there isn't one.
Until we extend dsa_loop to allow user space configuration, treat the
problem as a non-issue and just say that DSA ports found by tag_sja1105
are always sja1105 ports, which is in fact true. But keep the
dsa_port_is_sja1105 function so that it's easy to patch it during
testing, and rely on dead code elimination.
Fixes: 994d2cbb08 ("net: dsa: tag_sja1105: be dsa_loop-safe")
Link: https://lore.kernel.org/netdev/20210908220834.d7gmtnwrorhharna@skbuf/
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The problem is that DSA tagging protocols really must not depend on the
switch driver, because this creates a circular dependency at insmod
time, and the switch driver will effectively not load when the tagging
protocol driver is missing.
The code was structured in the way it was for a reason, though. The DSA
driver-facing API for PTP timestamping relies on the assumption that
two-step TX timestamps are provided by the hardware in an out-of-band
manner, typically by raising an interrupt and making that timestamp
available inside some sort of FIFO which is to be accessed over
SPI/MDIO/etc.
So the API puts .port_txtstamp into dsa_switch_ops, because it is
expected that the switch driver needs to save some state (like put the
skb into a queue until its TX timestamp arrives).
On SJA1110, TX timestamps are provided by the switch as Ethernet
packets, so this makes them be received and processed by the tagging
protocol driver. This in itself is great, because the timestamps are
full 64-bit and do not require reconstruction, and since Ethernet is the
fastest I/O method available to/from the switch, PTP timestamps arrive
very quickly, no matter how bottlenecked the SPI connection is, because
SPI interaction is not needed at all.
DSA's code structure and strict isolation between the tagging protocol
driver and the switch driver break the natural code organization.
When the tagging protocol driver receives a packet which is classified
as a metadata packet containing timestamps, it passes those timestamps
one by one to the switch driver, which then proceeds to compare them
based on the recorded timestamp ID that was generated in .port_txtstamp.
The communication between the tagging protocol and the switch driver is
done through a method exported by the switch driver, sja1110_process_meta_tstamp.
To satisfy build requirements, we force a dependency to build the
tagging protocol driver as a module when the switch driver is a module.
However, as explained in the first paragraph, that causes the circular
dependency.
To solve this, move the skb queue from struct sja1105_private :: struct
sja1105_ptp_data to struct sja1105_private :: struct sja1105_tagger_data.
The latter is a data structure for which hacks have already been put
into place to be able to create persistent storage per switch that is
accessible from the tagging protocol driver (see sja1105_setup_ports).
With the skb queue directly accessible from the tagging protocol driver,
we can now move sja1110_process_meta_tstamp into the tagging driver
itself, and avoid exporting a symbol.
Fixes: 566b18c8b7 ("net: dsa: sja1105: implement TX timestamping for SJA1110")
Link: https://lore.kernel.org/netdev/20210908220834.d7gmtnwrorhharna@skbuf/
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Flip the sign of a return value check, thereby suppressing the following
spurious error:
port 2 failed to notify DSA_NOTIFIER_BRIDGE_LEAVE: -EOPNOTSUPP
... which is emitted when removing an unoffloaded DSA switch port from a
bridge.
Fixes: d371b7c92d ("net: dsa: Unset vlan_filtering when ports leave the bridge")
Signed-off-by: Alvin Šipraga <alsi@bang-olufsen.dk>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20211012112730.3429157-1-alvin@pqrs.dk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
It was a documented fact that ds->ops->change_tag_protocol() offered
rtnetlink mutex protection to the switch driver, since there was an
ASSERT_RTNL right before the call in dsa_switch_change_tag_proto()
(initiated from sysfs).
The blamed commit introduced another call path for
ds->ops->change_tag_protocol() which does not hold the rtnl_mutex.
This is:
dsa_tree_setup
-> dsa_tree_setup_switches
-> dsa_switch_setup
-> dsa_switch_setup_tag_protocol
-> ds->ops->change_tag_protocol()
-> dsa_port_setup
-> dsa_slave_create
-> register_netdevice(slave_dev)
-> dsa_tree_setup_master
-> dsa_master_setup
-> dev->dsa_ptr = cpu_dp
The reason why the rtnl_mutex is held in the sysfs call path is to
ensure that, once the master and all the DSA interfaces are down (which
is required so that no packets flow), they remain down during the
tagging protocol change.
The above calling order illustrates the fact that it should not be risky
to change the initial tagging protocol to the one specified in the
device tree at the given time:
- packets cannot enter the dsa_switch_rcv() packet type handler since
netdev_uses_dsa() for the master will not yet return true, since
dev->dsa_ptr has not yet been populated
- packets cannot enter the dsa_slave_xmit() function because no DSA
interface has yet been registered
So from the DSA core's perspective, holding the rtnl_mutex is indeed not
necessary.
Yet, drivers may need to do things which need rtnl_mutex protection. For
example:
felix_set_tag_protocol
-> felix_setup_tag_8021q
-> dsa_tag_8021q_register
-> dsa_tag_8021q_setup
-> dsa_tag_8021q_port_setup
-> vlan_vid_add
-> ASSERT_RTNL
These drivers do not really have a choice to take the rtnl_mutex
themselves, since in the sysfs case, the rtnl_mutex is already held.
Fixes: deff710703 ("net: dsa: Allow default tag protocol to be overridden from DT")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Similar to commit 6087175b79 ("net: dsa: mt7530: use independent VLAN
learning on VLAN-unaware bridges"), software forwarding between an
unoffloaded LAG port (a bonding interface with an unsupported policy)
and a mv88e6xxx user port directly under a bridge is broken.
We adopt the same strategy, which is to make the standalone ports not
find any ATU entry learned on a bridge port.
Theory: the mv88e6xxx ATU is looked up by FID and MAC address. There are
as many FIDs as VIDs (4096). The FID is derived from the VID when
possible (the VTU maps a VID to a FID), with a fallback to the port
based default FID value when not (802.1Q Mode is disabled on the port,
or the classified VID isn't present in the VTU).
The mv88e6xxx driver makes the following use of FIDs and VIDs:
- the port's DefaultVID (to which untagged & pvid-tagged packets get
classified) is 0 and is absent from the VTU, so this kind of packets is
processed in FID 0, the default FID assigned by mv88e6xxx_setup_port.
- every time a bridge VLAN is created, mv88e6xxx_port_vlan_join() ->
mv88e6xxx_atu_new() associates a FID with that VID which increases
linearly starting from 1. Like this:
bridge vlan add dev lan0 vid 100 # FID 1
bridge vlan add dev lan1 vid 100 # still FID 1
bridge vlan add dev lan2 vid 1024 # FID 2
The FID allocation made by the driver is sub-optimal for the following
reasons:
(a) A standalone port has a DefaultPVID of 0 and a default FID of 0 too.
A VLAN-unaware bridged port has a DefaultPVID of 0 and a default FID
of 0 too. The difference is that the bridged ports may learn ATU
entries, while the standalone port has the requirement that it must
not, and must not find them either. Standalone ports must not use
the same FID as ports belonging to a bridge. All standalone ports
can use the same FID, since the ATU will never have an entry in
that FID.
(b) Multiple VLAN-unaware bridges will all use a DefaultPVID of 0 and a
default FID of 0 on all their ports. The FDBs will not be isolated
between these bridges. Every VLAN-unaware bridge must use the same
FID on all its ports, different from the FID of other bridge ports.
(c) Each bridge VLAN uses a unique FID which is useful for Independent
VLAN Learning, but the same VLAN ID on multiple VLAN-aware bridges
will result in the same FID being used by mv88e6xxx_atu_new().
The correct behavior is for VLAN 1 in br0 to have a different FID
compared to VLAN 1 in br1.
This patch cannot fix all the above. Traditionally the DSA framework did
not care about this, and the reality is that DSA core involvement is
needed for the aforementioned issues to be solved. The only thing we can
solve here is an issue which does not require API changes, and that is
issue (a), aka use a different FID for standalone ports vs ports under
VLAN-unaware bridges.
The first step is deciding what VID and FID to use for standalone ports,
and what VID and FID for bridged ports. The 0/0 pair for standalone
ports is what they used up till now, let's keep using that. For bridged
ports, there are 2 cases:
- VLAN-aware ports will never end up using the port default FID, because
packets will always be classified to a VID in the VTU or dropped
otherwise. The FID is the one associated with the VID in the VTU.
- On VLAN-unaware ports, we _could_ leave their DefaultVID (pvid) at
zero (just as in the case of standalone ports), and just change the
port's default FID from 0 to a different number (say 1).
However, Tobias points out that there is one more requirement to cater to:
cross-chip bridging. The Marvell DSA header does not carry the FID in
it, only the VID. So once a packet crosses a DSA link, if it has a VID
of zero it will get classified to the default FID of that cascade port.
Relying on a port default FID for upstream cascade ports results in
contradictions: a default FID of 0 breaks ATU isolation of bridged ports
on the downstream switch, a default FID of 1 breaks standalone ports on
the downstream switch.
So not only must standalone ports have different FIDs compared to
bridged ports, they must also have different DefaultVID values.
IEEE 802.1Q defines two reserved VID values: 0 and 4095. So we simply
choose 4095 as the DefaultVID of ports belonging to VLAN-unaware
bridges, and VID 4095 maps to FID 1.
For the xmit operation to look up the same ATU database, we need to put
VID 4095 in DSA tags sent to ports belonging to VLAN-unaware bridges
too. All shared ports are configured to map this VID to the bridging
FID, because they are members of that VLAN in the VTU. Shared ports
don't need to have 802.1QMode enabled in any way, they always parse the
VID from the DSA header, they don't need to look at the 802.1Q header.
We install VID 4095 to the VTU in mv88e6xxx_setup_port(), with the
mention that mv88e6xxx_vtu_setup() which was located right below that
call was flushing the VTU so those entries wouldn't be preserved.
So we need to relocate the VTU flushing prior to the port initialization
during ->setup(). Also note that this is why it is safe to assume that
VID 4095 will get associated with FID 1: the user ports haven't been
created, so there is no avenue for the user to create a bridge VLAN
which could otherwise race with the creation of another FID which would
otherwise use up the non-reserved FID value of 1.
[ Currently mv88e6xxx_port_vlan_join() doesn't have the option of
specifying a preferred FID, it always calls mv88e6xxx_atu_new(). ]
mv88e6xxx_port_db_load_purge() is the function to access the ATU for
FDB/MDB entries, and it used to determine the FID to use for
VLAN-unaware FDB entries (VID=0) using mv88e6xxx_port_get_fid().
But the driver only called mv88e6xxx_port_set_fid() once, during probe,
so no surprises, the port FID was always 0, the call to get_fid() was
redundant. As much as I would have wanted to not touch that code, the
logic is broken when we add a new FID which is not the port-based
default. Now the port-based default FID only corresponds to standalone
ports, and FDB/MDB entries belong to the bridging service. So while in
the future, when the DSA API will support FDB isolation, we will have to
figure out the FID based on the bridge number, for now there's a single
bridging FID, so hardcode that.
Lastly, the tagger needs to check, when it is transmitting a VLAN
untagged skb, whether it is sending it towards a bridged or a standalone
port. When we see it is bridged we assume the bridge is VLAN-unaware.
Not because it cannot be VLAN-aware but:
- if we are transmitting from a VLAN-aware bridge we are likely doing so
using TX forwarding offload. That code path guarantees that skbs have
a vlan hwaccel tag in them, so we would not enter the "else" branch
of the "if (skb->protocol == htons(ETH_P_8021Q))" condition.
- if we are transmitting on behalf of a VLAN-aware bridge but with no TX
forwarding offload (no PVT support, out of space in the PVT, whatever),
we would indeed be transmitting with VLAN 4095 instead of the bridge
device's pvid. However we would be injecting a "From CPU" frame, and
the switch won't learn from that - it only learns from "Forward" frames.
So it is inconsequential for address learning. And VLAN 4095 is
absolutely enough for the frame to exit the switch, since we never
remove that VLAN from any port.
Fixes: 57e661aae6 ("net: dsa: mv88e6xxx: Link aggregation support")
Reported-by: Tobias Waldekranz <tobias@waldekranz.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The present code is structured this way due to an incomplete thought
process. In Documentation/networking/switchdev.rst we document that if a
bridge is VLAN-unaware, then the presence or lack of a pvid on a bridge
port (or on the bridge itself, for that matter) should not affect the
ability to receive and transmit tagged or untagged packets.
If the bridge on behalf of which we are sending this packet is
VLAN-aware, then the TX forwarding offload API ensures that the skb will
be VLAN-tagged (if the packet was sent by user space as untagged, it
will get transmitted town to the driver as tagged with the bridge
device's pvid). But if the bridge is VLAN-unaware, it may or may not be
VLAN-tagged. In fact the logic to insert the bridge's PVID came from the
idea that we should emulate what is being done in the VLAN-aware case.
But we shouldn't.
It appears that injecting packets using a VLAN ID of 0 serves the
purpose of forwarding the packets to the egress port with no VLAN tag
added or stripped by the hardware, and no filtering being performed.
So we can simply remove the superfluous logic.
One reason why this logic is broken is that when CONFIG_BRIDGE_VLAN_FILTERING=n,
we call br_vlan_get_pvid_rcu() but that returns an error and we do error
out, dropping all packets on xmit. Not really smart. This is also an
issue when the user deletes the bridge pvid:
$ bridge vlan del dev br0 vid 1 self
As mentioned, in both cases, packets should still flow freely, and they
do just that on any net device where the bridge is not offloaded, but on
mv88e6xxx they don't.
Fixes: d82f8ab0d8 ("net: dsa: tag_dsa: offload the bridge forwarding process")
Reported-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patchwork.kernel.org/project/netdevbpf/patch/20211003155141.2241314-1-andrew@lunn.ch/
Link: https://patchwork.kernel.org/project/netdevbpf/patch/20210928233708.1246774-1-vladimir.oltean@nxp.com/
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The dp->bridge_num is zero-based, with -1 being the encoding for an
invalid value. But dsa_bridge_num_put used to check for an invalid value
by comparing bridge_num with 0, which is of course incorrect.
The result is that the bridge_num will never get cleared by
dsa_bridge_num_put, and further port joins to other bridges will get a
bridge_num larger than the previous one, and once all the available
bridges with TX forwarding offload supported by the hardware get
exhausted, the TX forwarding offload feature is simply disabled.
In the case of sja1105, 7 iterations of the loop below are enough to
exhaust the TX forwarding offload bits, and further bridge joins operate
without that feature.
ip link add br0 type bridge vlan_filtering 1
while :; do
ip link set sw0p2 master br0 && sleep 1
ip link set sw0p2 nomaster && sleep 1
done
This issue is enough of an indication that having the dp->bridge_num
invalid encoding be a negative number is prone to bugs, so this will be
changed to a one-based value, with the dp->bridge_num of zero being the
indication of no bridge. However, that is material for net-next.
Fixes: f5e165e72b ("net: dsa: track unique bridge numbers across all DSA switch trees")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
A packet received on a trunk will have bit 2 set in Forward DSA tagged
frame. Bit 1 can be either 0 or 1 and is otherwise undefined and bit 0
indicates the frame CFI. Masking with 7 thus results in frames as
being identified as being from a trunk when in fact they are not. Fix
the mask to just look at bit 2.
Fixes: 5b60dadb71 ("net: dsa: tag_dsa: Support reception of packets from LAG devices")
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Linux device model permits both the ->shutdown and ->remove driver
methods to get called during a shutdown procedure. Example: a DSA switch
which sits on an SPI bus, and the SPI bus driver calls this on its
->shutdown method:
spi_unregister_controller
-> device_for_each_child(&ctlr->dev, NULL, __unregister);
-> spi_unregister_device(to_spi_device(dev));
-> device_del(&spi->dev);
So this is a simple pattern which can theoretically appear on any bus,
although the only other buses on which I've been able to find it are
I2C:
i2c_del_adapter
-> device_for_each_child(&adap->dev, NULL, __unregister_client);
-> i2c_unregister_device(client);
-> device_unregister(&client->dev);
The implication of this pattern is that devices on these buses can be
unregistered after having been shut down. The drivers for these devices
might choose to return early either from ->remove or ->shutdown if the
other callback has already run once, and they might choose that the
->shutdown method should only perform a subset of the teardown done by
->remove (to avoid unnecessary delays when rebooting).
So in other words, the device driver may choose on ->remove to not
do anything (therefore to not unregister an MDIO bus it has registered
on ->probe), because this ->remove is actually triggered by the
device_shutdown path, and its ->shutdown method has already run and done
the minimally required cleanup.
This used to be fine until the blamed commit, but now, the following
BUG_ON triggers:
void mdiobus_free(struct mii_bus *bus)
{
/* For compatibility with error handling in drivers. */
if (bus->state == MDIOBUS_ALLOCATED) {
kfree(bus);
return;
}
BUG_ON(bus->state != MDIOBUS_UNREGISTERED);
bus->state = MDIOBUS_RELEASED;
put_device(&bus->dev);
}
In other words, there is an attempt to free an MDIO bus which was not
unregistered. The attempt to free it comes from the devres release
callbacks of the SPI device, which are executed after the device is
unregistered.
I'm not saying that the fact that MDIO buses allocated using devres
would automatically get unregistered wasn't strange. I'm just saying
that the commit didn't care about auditing existing call paths in the
kernel, and now, the following code sequences are potentially buggy:
(a) devm_mdiobus_alloc followed by plain mdiobus_register, for a device
located on a bus that unregisters its children on shutdown. After
the blamed patch, either both the alloc and the register should use
devres, or none should.
(b) devm_mdiobus_alloc followed by plain mdiobus_register, and then no
mdiobus_unregister at all in the remove path. After the blamed
patch, nobody unregisters the MDIO bus anymore, so this is even more
buggy than the previous case which needs a specific bus
configuration to be seen, this one is an unconditional bug.
In this case, DSA falls into category (a), it tries to be helpful and
registers an MDIO bus on behalf of the switch, which might be on such a
bus. I've no idea why it does it under devres.
It does this on probe:
if (!ds->slave_mii_bus && ds->ops->phy_read)
alloc and register mdio bus
and this on remove:
if (ds->slave_mii_bus && ds->ops->phy_read)
unregister mdio bus
I _could_ imagine using devres because the condition used on remove is
different than the condition used on probe. So strictly speaking, DSA
cannot determine whether the ds->slave_mii_bus it sees on remove is the
ds->slave_mii_bus that _it_ has allocated on probe. Using devres would
have solved that problem. But nonetheless, the existing code already
proceeds to unregister the MDIO bus, even though it might be
unregistering an MDIO bus it has never registered. So I can only guess
that no driver that implements ds->ops->phy_read also allocates and
registers ds->slave_mii_bus itself.
So in that case, if unregistering is fine, freeing must be fine too.
Stop using devres and free the MDIO bus manually. This will make devres
stop attempting to free a still registered MDIO bus on ->shutdown.
Fixes: ac3a68d566 ("net: phy: don't abuse devres in devm_mdiobus_register()")
Reported-by: Lino Sanfilippo <LinoSanfilippo@gmx.de>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Tested-by: Lino Sanfilippo <LinoSanfilippo@gmx.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since the blamed commit, dsa_tree_teardown_switches() was split into two
smaller functions, dsa_tree_teardown_switches and dsa_tree_teardown_ports.
However, the error path of dsa_tree_setup stopped calling dsa_tree_teardown_ports.
Fixes: a57d8c217a ("net: dsa: flush switchdev workqueue before tearing down CPU/DSA ports")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 86f8b1c01a ("net: dsa: Do not make user port errors fatal")
decided it was fine to ignore errors on certain ports that fail to
probe, and go on with the ports that do probe fine.
Commit fb6ec87f72 ("net: dsa: Fix type was not set for devlink port")
noticed that devlink_port_type_eth_set(dlp, dp->slave); does not get
called, and devlink notices after a timeout of 3600 seconds and prints a
WARN_ON. So it went ahead to unregister the devlink port. And because
there exists an UNUSED port flavour, we actually re-register the devlink
port as UNUSED.
Commit 08156ba430 ("net: dsa: Add devlink port regions support to
DSA") added devlink port regions, which are set up by the driver and not
by DSA.
When we trigger the devlink port deregistration and reregistration as
unused, devlink now prints another WARN_ON, from here:
devlink_port_unregister:
WARN_ON(!list_empty(&devlink_port->region_list));
So the port still has regions, which makes sense, because they were set
up by the driver, and the driver doesn't know we're unregistering the
devlink port.
Somebody needs to tear them down, and optionally (actually it would be
nice, to be consistent) set them up again for the new devlink port.
But DSA's layering stays in our way quite badly here.
The options I've considered are:
1. Introduce a function in devlink to just change a port's type and
flavour. No dice, devlink keeps a lot of state, it really wants the
port to not be registered when you set its parameters, so changing
anything can only be done by destroying what we currently have and
recreating it.
2. Make DSA cache the parameters passed to dsa_devlink_port_region_create,
and the region returned, keep those in a list, then when the devlink
port unregister needs to take place, the existing devlink regions are
destroyed by DSA, and we replay the creation of new regions using the
cached parameters. Problem: mv88e6xxx keeps the region pointers in
chip->ports[port].region, and these will remain stale after DSA frees
them. There are many things DSA can do, but updating mv88e6xxx's
private pointers is not one of them.
3. Just let the driver do it (i.e. introduce a very specific method
called ds->ops->port_reinit_as_unused, which unregisters its devlink
port devlink regions, then the old devlink port, then registers the
new one, then the devlink port regions for it). While it does work,
as opposed to the others, it's pretty horrible from an API
perspective and we can do better.
4. Introduce a new pair of methods, ->port_setup and ->port_teardown,
which in the case of mv88e6xxx must register and unregister the
devlink port regions. Call these 2 methods when the port must be
reinitialized as unused.
Naturally, I went for the 4th approach.
Fixes: 08156ba430 ("net: dsa: Add devlink port regions support to DSA")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Lino reports that on his system with bcmgenet as DSA master and KSZ9897
as a switch, rebooting or shutting down never works properly.
What does the bcmgenet driver have special to trigger this, that other
DSA masters do not? It has an implementation of ->shutdown which simply
calls its ->remove implementation. Otherwise said, it unregisters its
network interface on shutdown.
This message can be seen in a loop, and it hangs the reboot process there:
unregister_netdevice: waiting for eth0 to become free. Usage count = 3
So why 3?
A usage count of 1 is normal for a registered network interface, and any
virtual interface which links itself as an upper of that will increment
it via dev_hold. In the case of DSA, this is the call path:
dsa_slave_create
-> netdev_upper_dev_link
-> __netdev_upper_dev_link
-> __netdev_adjacent_dev_insert
-> dev_hold
So a DSA switch with 3 interfaces will result in a usage count elevated
by two, and netdev_wait_allrefs will wait until they have gone away.
Other stacked interfaces, like VLAN, watch NETDEV_UNREGISTER events and
delete themselves, but DSA cannot just vanish and go poof, at most it
can unbind itself from the switch devices, but that must happen strictly
earlier compared to when the DSA master unregisters its net_device, so
reacting on the NETDEV_UNREGISTER event is way too late.
It seems that it is a pretty established pattern to have a driver's
->shutdown hook redirect to its ->remove hook, so the same code is
executed regardless of whether the driver is unbound from the device, or
the system is just shutting down. As Florian puts it, it is quite a big
hammer for bcmgenet to unregister its net_device during shutdown, but
having a common code path with the driver unbind helps ensure it is well
tested.
So DSA, for better or for worse, has to live with that and engage in an
arms race of implementing the ->shutdown hook too, from all individual
drivers, and do something sane when paired with masters that unregister
their net_device there. The only sane thing to do, of course, is to
unlink from the master.
However, complications arise really quickly.
The pattern of redirecting ->shutdown to ->remove is not unique to
bcmgenet or even to net_device drivers. In fact, SPI controllers do it
too (see dspi_shutdown -> dspi_remove), and presumably, I2C controllers
and MDIO controllers do it too (this is something I have not researched
too deeply, but even if this is not the case today, it is certainly
plausible to happen in the future, and must be taken into consideration).
Since DSA switches might be SPI devices, I2C devices, MDIO devices, the
insane implication is that for the exact same DSA switch device, we
might have both ->shutdown and ->remove getting called.
So we need to do something with that insane environment. The pattern
I've come up with is "if this, then not that", so if either ->shutdown
or ->remove gets called, we set the device's drvdata to NULL, and in the
other hook, we check whether the drvdata is NULL and just do nothing.
This is probably not necessary for platform devices, just for devices on
buses, but I would really insist for consistency among drivers, because
when code is copy-pasted, it is not always copy-pasted from the best
sources.
So depending on whether the DSA switch's ->remove or ->shutdown will get
called first, we cannot really guarantee even for the same driver if
rebooting will result in the same code path on all platforms. But
nonetheless, we need to do something minimally reasonable on ->shutdown
too to fix the bug. Of course, the ->remove will do more (a full
teardown of the tree, with all data structures freed, and this is why
the bug was not caught for so long). The new ->shutdown method is kept
separate from dsa_unregister_switch not because we couldn't have
unregistered the switch, but simply in the interest of doing something
quick and to the point.
The big question is: does the DSA switch's ->shutdown get called earlier
than the DSA master's ->shutdown? If not, there is still a risk that we
might still trigger the WARN_ON in unregister_netdevice that says we are
attempting to unregister a net_device which has uppers. That's no good.
Although the reference to the master net_device won't physically go away
even if DSA's ->shutdown comes afterwards, remember we have a dev_hold
on it.
The answer to that question lies in this comment above device_link_add:
* A side effect of the link creation is re-ordering of dpm_list and the
* devices_kset list by moving the consumer device and all devices depending
* on it to the ends of these lists (that does not happen to devices that have
* not been registered when this function is called).
so the fact that DSA uses device_link_add towards its master is not
exactly for nothing. device_shutdown() walks devices_kset from the back,
so this is our guarantee that DSA's shutdown happens before the master's
shutdown.
Fixes: 2f1e8ea726 ("net: dsa: link interfaces with the DSA master to get rid of lockdep warnings")
Link: https://lore.kernel.org/netdev/20210909095324.12978-1-LinoSanfilippo@gmx.de/
Reported-by: Lino Sanfilippo <LinoSanfilippo@gmx.de>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Tested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
NXP Legal insists that the following are not fine:
- Saying "NXP Semiconductors" instead of "NXP", since the company's
registered name is "NXP"
- Putting a "(c)" sign in the copyright string
- Putting a comma in the copyright string
The only accepted copyright string format is "Copyright <year-range> NXP".
This patch changes the copyright headers in the networking files that
were sent by me, or derived from code sent by me.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sometimes when unbinding the mv88e6xxx driver on Turris MOX, these error
messages appear:
mv88e6085 d0032004.mdio-mii:12: port 1 failed to delete be:79:b4:9e:9e:96 vid 1 from fdb: -2
mv88e6085 d0032004.mdio-mii:12: port 1 failed to delete be:79:b4:9e:9e:96 vid 0 from fdb: -2
mv88e6085 d0032004.mdio-mii:12: port 1 failed to delete d8:58:d7:00:ca:6d vid 100 from fdb: -2
mv88e6085 d0032004.mdio-mii:12: port 1 failed to delete d8:58:d7:00:ca:6d vid 1 from fdb: -2
mv88e6085 d0032004.mdio-mii:12: port 1 failed to delete d8:58:d7:00:ca:6d vid 0 from fdb: -2
(and similarly for other ports)
What happens is that DSA has a policy "even if there are bugs, let's at
least not leak memory" and dsa_port_teardown() clears the dp->fdbs and
dp->mdbs lists, which are supposed to be empty.
But deleting that cleanup code, the warnings go away.
=> the FDB and MDB lists (used for refcounting on shared ports, aka CPU
and DSA ports) will eventually be empty, but are not empty by the time
we tear down those ports. Aka we are deleting them too soon.
The addresses that DSA complains about are host-trapped addresses: the
local addresses of the ports, and the MAC address of the bridge device.
The problem is that offloading those entries happens from a deferred
work item scheduled by the SWITCHDEV_FDB_DEL_TO_DEVICE handler, and this
races with the teardown of the CPU and DSA ports where the refcounting
is kept.
In fact, not only it races, but fundamentally speaking, if we iterate
through the port list linearly, we might end up tearing down the shared
ports even before we delete a DSA user port which has a bridge upper.
So as it turns out, we need to first tear down the user ports (and the
unused ones, for no better place of doing that), then the shared ports
(the CPU and DSA ports). In between, we need to ensure that all work
items scheduled by our switchdev handlers (which only run for user
ports, hence the reason why we tear them down first) have finished.
Fixes: 161ca59d39 ("net: dsa: reference count the MDB entries at the cross-chip notifier level")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20210914134726.2305133-1-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
DSA supports connecting to a phy-handle, and has a fallback to a non-OF
based method of connecting to an internal PHY on the switch's own MDIO
bus, if no phy-handle and no fixed-link nodes were present.
The -ENODEV error code from the first attempt (phylink_of_phy_connect)
is what triggers the second attempt (phylink_connect_phy).
However, when the first attempt returns a different error code than
-ENODEV, this results in an unbalance of calls to phylink_create and
phylink_destroy by the time we exit the function. The phylink instance
has leaked.
There are many other error codes that can be returned by
phylink_of_phy_connect. For example, phylink_validate returns -EINVAL.
So this is a practical issue too.
Fixes: aab9c4067d ("net: dsa: Plug in PHYLINK support")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://lore.kernel.org/r/20210914134331.2303380-1-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
I noticed that only port 0 worked on the RTL8366RB since we
started to use custom tags.
It turns out that the format of egress custom tags is actually
different from ingress custom tags. While the lower bits just
contain the port number in ingress tags, egress tags need to
indicate destination port by setting the bit for the
corresponding port.
It was working on port 0 because port 0 added 0x00 as port
number in the lower bits, and if you do this the packet appears
at all ports, including the intended port. Ooops.
Fix this and all ports work again. Use the define for shifting
the "type A" into place while we're at it.
Tested on the D-Link DIR-685 by sending traffic to each of
the ports in turn. It works.
Fixes: 86dd9868b8 ("net: dsa: tag_rtl4_a: Support also egress tags")
Cc: DENG Qingfang <dqfext@gmail.com>
Cc: Mauri Sandberg <sandberg@mailfence.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduced in commit 38b5beeae7 ("net: dsa: sja1105: prepare tagger
for handling DSA tags and VLAN simultaneously"), the sja1105_xmit_tpid
function solved quite a different problem than our needs are now.
Then, we used best-effort VLAN filtering and we were using the xmit_tpid
to tunnel packets coming from an 8021q upper through the TX VLAN allocated
by tag_8021q to that egress port. The need for a different VLAN protocol
depending on switch revision came from the fact that this in itself was
more of a hack to trick the hardware into accepting tunneled VLANs in
the first place.
Right now, we deny 8021q uppers (see sja1105_prechangeupper). Even if we
supported them again, we would not do that using the same method of
{tunneling the VLAN on egress, retagging the VLAN on ingress} that we
had in the best-effort VLAN filtering mode. It seems rather simpler that
we just allocate a VLAN in the VLAN table that is simply not used by the
bridge at all, or by any other port.
Anyway, I have 2 gripes with the current sja1105_xmit_tpid:
1. When sending packets on behalf of a VLAN-aware bridge (with the new
TX forwarding offload framework) plus untagged (with the tag_8021q
VLAN added by the tagger) packets, we can see that on SJA1105P/Q/R/S
and later (which have a qinq_tpid of ETH_P_8021AD), some packets sent
through the DSA master have a VLAN protocol of 0x8100 and others of
0x88a8. This is strange and there is no reason for it now. If we have
a bridge and are therefore forced to send using that bridge's TPID,
we can as well blend with that bridge's VLAN protocol for all packets.
2. The sja1105_xmit_tpid introduces a dependency on the sja1105 driver,
because it looks inside dp->priv. It is desirable to keep as much
separation between taggers and switch drivers as possible. Now it
doesn't do that anymore.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The sja1105 driver is a bit special in its use of VLAN headers as DSA
tags. This is because in VLAN-aware mode, the VLAN headers use an actual
TPID of 0x8100, which is understood even by the DSA master as an actual
VLAN header.
Furthermore, control packets such as PTP and STP are transmitted with no
VLAN header as a DSA tag, because, depending on switch generation, there
are ways to steer these control packets towards a precise egress port
other than VLAN tags. Transmitting control packets as untagged means
leaving a door open for traffic in general to be transmitted as untagged
from the DSA master, and for it to traverse the switch and exit a random
switch port according to the FDB lookup.
This behavior is a bit out of line with other DSA drivers which have
native support for DSA tagging. There, it is to be expected that the
switch only accepts DSA-tagged packets on its CPU port, dropping
everything that does not match this pattern.
We perhaps rely a bit too much on the switches' hardware dropping on the
CPU port, and place no other restrictions in the kernel data path to
avoid that. For example, sja1105 is also a bit special in that STP/PTP
packets are transmitted using "management routes"
(sja1105_port_deferred_xmit): when sending a link-local packet from the
CPU, we must first write a SPI message to the switch to tell it to
expect a packet towards multicast MAC DA 01-80-c2-00-00-0e, and to route
it towards port 3 when it gets it. This entry expires as soon as it
matches a packet received by the switch, and it needs to be reinstalled
for the next packet etc. All in all quite a ghetto mechanism, but it is
all that the sja1105 switches offer for injecting a control packet.
The driver takes a mutex for serializing control packets and making the
pairs of SPI writes of a management route and its associated skb atomic,
but to be honest, a mutex is only relevant as long as all parties agree
to take it. With the DSA design, it is possible to open an AF_PACKET
socket on the DSA master net device, and blast packets towards
01-80-c2-00-00-0e, and whatever locking the DSA switch driver might use,
it all goes kaput because management routes installed by the driver will
match skbs sent by the DSA master, and not skbs generated by the driver
itself. So they will end up being routed on the wrong port.
So through the lens of that, maybe it would make sense to avoid that
from happening by doing something in the network stack, like: introduce
a new bit in struct sk_buff, like xmit_from_dsa. Then, somewhere around
dev_hard_start_xmit(), introduce the following check:
if (netdev_uses_dsa(dev) && !skb->xmit_from_dsa)
kfree_skb(skb);
Ok, maybe that is a bit drastic, but that would at least prevent a bunch
of problems. For example, right now, even though the majority of DSA
switches drop packets without DSA tags sent by the DSA master (and
therefore the majority of garbage that user space daemons like avahi and
udhcpcd and friends create), it is still conceivable that an aggressive
user space program can open an AF_PACKET socket and inject a spoofed DSA
tag directly on the DSA master. We have no protection against that; the
packet will be understood by the switch and be routed wherever user
space says. Furthermore: there are some DSA switches where we even have
register access over Ethernet, using DSA tags. So even user space
drivers are possible in this way. This is a huge hole.
However, the biggest thing that bothers me is that udhcpcd attempts to
ask for an IP address on all interfaces by default, and with sja1105, it
will attempt to get a valid IP address on both the DSA master as well as
on sja1105 switch ports themselves. So with IP addresses in the same
subnet on multiple interfaces, the routing table will be messed up and
the system will be unusable for traffic until it is configured manually
to not ask for an IP address on the DSA master itself.
It turns out that it is possible to avoid that in the sja1105 driver, at
least very superficially, by requesting the switch to drop VLAN-untagged
packets on the CPU port. With the exception of control packets, all
traffic originated from tag_sja1105.c is already VLAN-tagged, so only
STP and PTP packets need to be converted. For that, we need to uphold
the equivalence between an untagged and a pvid-tagged packet, and to
remember that the CPU port of sja1105 uses a pvid of 4095.
Now that we drop untagged traffic on the CPU port, non-aggressive user
space applications like udhcpcd stop bothering us, and sja1105 effectively
becomes just as vulnerable to the aggressive kind of user space programs
as other DSA switches are (ok, users can also create 8021q uppers on top
of the DSA master in the case of sja1105, but in future patches we can
easily deny that, but it still doesn't change the fact that VLAN-tagged
packets can still be injected over raw sockets).
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As explained in commit e358bef7c3 ("net: dsa: Give drivers the chance
to veto certain upper devices"), the hellcreek driver uses some tricks
to comply with the network stack expectations: it enforces port
separation in standalone mode using VLANs. For untagged traffic,
bridging between ports is prevented by using different PVIDs, and for
VLAN-tagged traffic, it never accepts 8021q uppers with the same VID on
two ports, so packets with one VLAN cannot leak from one port to another.
That is almost fine*, and has worked because hellcreek relied on an
implicit behavior of the DSA core that was changed by the previous
patch: the standalone ports declare the 'rx-vlan-filter' feature as 'on
[fixed]'. Since most of the DSA drivers are actually VLAN-unaware in
standalone mode, that feature was actually incorrectly reflecting the
hardware/driver state, so there was a desire to fix it. This leaves the
hellcreek driver in a situation where it has to explicitly request this
behavior from the DSA framework.
We configure the ports as follows:
- Standalone: 'rx-vlan-filter' is on. An 8021q upper on top of a
standalone hellcreek port will go through dsa_slave_vlan_rx_add_vid
and will add a VLAN to the hardware tables, giving the driver the
opportunity to refuse it through .port_prechangeupper.
- Bridged with vlan_filtering=0: 'rx-vlan-filter' is off. An 8021q upper
on top of a bridged hellcreek port will not go through
dsa_slave_vlan_rx_add_vid, because there will not be any attempt to
offload this VLAN. The driver already disables VLAN awareness, so that
upper should receive the traffic it needs.
- Bridged with vlan_filtering=1: 'rx-vlan-filter' is on. An 8021q upper
on top of a bridged hellcreek port will call dsa_slave_vlan_rx_add_vid,
and can again be vetoed through .port_prechangeupper.
*It is not actually completely fine, because if I follow through
correctly, we can have the following situation:
ip link add br0 type bridge vlan_filtering 0
ip link set lan0 master br0 # lan0 now becomes VLAN-unaware
ip link set lan0 nomaster # lan0 fails to become VLAN-aware again, therefore breaking isolation
This patch fixes that corner case by extending the DSA core logic, based
on this requested attribute, to change the VLAN awareness state of the
switch (port) when it leaves the bridge.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Kurt Kanzenbach <kurt@linutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
There have been multiple independent reports about
dsa_slave_vlan_rx_add_vid being called (and consequently calling the
drivers' .port_vlan_add) when it isn't needed, and sometimes (not
always) causing problems in the process.
Case 1:
mv88e6xxx_port_vlan_prepare is stubborn and only accepts VLANs on
bridged ports. That is understandably so, because standalone mv88e6xxx
ports are VLAN-unaware, and VTU entries are said to be a scarce
resource.
Otherwise said, the following fails lamentably on mv88e6xxx:
ip link add br0 type bridge vlan_filtering 1
ip link set lan3 master br0
ip link add link lan10 name lan10.1 type vlan id 1
[485256.724147] mv88e6085 d0032004.mdio-mii:12: p10: hw VLAN 1 already used by port 3 in br0
RTNETLINK answers: Operation not supported
This has become a worse issue since commit 9b236d2a69 ("net: dsa:
Advertise the VLAN offload netdev ability only if switch supports it").
Up to that point, the driver was returning -EOPNOTSUPP and DSA was
reconverting that error to 0, making the 8021q upper think all is ok
(but obviously the error message was there even prior to this change).
After that change the -EOPNOTSUPP is propagated to vlan_vid_add, and it
is a hard error.
Case 2:
Ports that don't offload the Linux bridge (have a dp->bridge_dev = NULL
because they don't implement .port_bridge_{join,leave}). Understandably,
a standalone port should not offload VLANs either, it should remain VLAN
unaware and any VLAN should be a software VLAN (as long as the hardware
is not quirky, that is).
In fact, dsa_slave_port_obj_add does do the right thing and rejects
switchdev VLAN objects coming from the bridge when that bridge is not
offloaded:
case SWITCHDEV_OBJ_ID_PORT_VLAN:
if (!dsa_port_offloads_bridge_port(dp, obj->orig_dev))
return -EOPNOTSUPP;
err = dsa_slave_vlan_add(dev, obj, extack);
But it seems that the bridge is able to trick us. The __vlan_vid_add
from br_vlan.c has:
/* Try switchdev op first. In case it is not supported, fallback to
* 8021q add.
*/
err = br_switchdev_port_vlan_add(dev, v->vid, flags, extack);
if (err == -EOPNOTSUPP)
return vlan_vid_add(dev, br->vlan_proto, v->vid);
So it says "no, no, you need this VLAN in your life!". And we, naive as
we are, say "oh, this comes from the vlan_vid_add code path, it must be
an 8021q upper, sure, I'll take that". And we end up with that bridge
VLAN installed on our port anyway. But this time, it has the wrong flags:
if the bridge was trying to install VLAN 1 as a pvid/untagged VLAN,
failed via switchdev, retried via vlan_vid_add, we have this comment:
/* This API only allows programming tagged, non-PVID VIDs */
So what we do makes absolutely no sense.
Backtracing a bit, we see the common pattern. We allow the network stack
to think that our standalone ports are VLAN-aware, but they aren't, for
the vast majority of switches. The quirky ones should not dictate the
norm. The dsa_slave_vlan_rx_add_vid and dsa_slave_vlan_rx_kill_vid
methods exist for drivers that need the 'rx-vlan-filter: on' feature in
ethtool -k, which can be due to any of the following reasons:
1. vlan_filtering_is_global = true, and some ports are under a
VLAN-aware bridge while others are standalone, and the standalone
ports would otherwise drop VLAN-tagged traffic. This is described in
commit 061f6a505a ("net: dsa: Add ndo_vlan_rx_{add, kill}_vid
implementation").
2. the ports that are under a VLAN-aware bridge should also set this
feature, for 8021q uppers having a VID not claimed by the bridge.
In this case, the driver will essentially not even know that the VID
is coming from the 8021q layer and not the bridge.
3. Hellcreek. This driver needs it because in standalone mode, it uses
unique VLANs per port to ensure separation. For separation of untagged
traffic, it uses different PVIDs for each port, and for separation of
VLAN-tagged traffic, it never accepts 8021q uppers with the same vid
on two ports.
If a driver does not fall under any of the above 3 categories, there is
no reason why it should advertise the 'rx-vlan-filter' feature, therefore
no reason why it should offload the VLANs added through vlan_vid_add.
This commit fixes the problem by removing the 'rx-vlan-filter' feature
from the slave devices when they operate in standalone mode, and when
they offload a VLAN-unaware bridge.
The way it works is that vlan_vid_add will now stop its processing here:
vlan_add_rx_filter_info:
if (!vlan_hw_filter_capable(dev, proto))
return 0;
So the VLAN will still be saved in the interface's VLAN RX filtering
list, but because it does not declare VLAN filtering in its features,
the 8021q module will return zero without committing that VLAN to
hardware.
This gives the drivers what they want, since it keeps the 8021q VLANs
away from the VLAN table until VLAN awareness is enabled (point at which
the ports are no longer standalone, hence in the mv88e6xxx case, the
check in mv88e6xxx_port_vlan_prepare passes).
Since the issue predates the existence of the hellcreek driver, case 3
will be dealt with in a separate patch.
The main change that this patch makes is to no longer set
NETIF_F_HW_VLAN_CTAG_FILTER unconditionally, but toggle it dynamically
(for most switches, never).
The second part of the patch addresses an issue that the first part
introduces: because the 'rx-vlan-filter' feature is now dynamically
toggled, and our .ndo_vlan_rx_add_vid does not get called when
'rx-vlan-filter' is off, we need to avoid bugs such as the following by
replaying the VLANs from 8021q uppers every time we enable VLAN
filtering:
ip link add link lan0 name lan0.100 type vlan id 100
ip addr add 192.168.100.1/24 dev lan0.100
ping 192.168.100.2 # should work
ip link add br0 type bridge vlan_filtering 0
ip link set lan0 master br0
ping 192.168.100.2 # should still work
ip link set br0 type bridge vlan_filtering 1
ping 192.168.100.2 # should still work but doesn't
As reported by Florian, some drivers look at ds->vlan_filtering in
their .port_vlan_add() implementation. So this patch also makes sure
that ds->vlan_filtering is committed before calling the driver. This is
the reason why it is first committed, then restored on the failure path.
Reported-by: Tobias Waldekranz <tobias@waldekranz.com>
Reported-by: Alvin Šipraga <alsi@bang-olufsen.dk>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Tested-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the driver does not implement .port_bridge_{join,leave}, then we must
fall back to standalone operation on that port, and trigger the error
path of dsa_port_bridge_join. This sets dp->bridge_dev = NULL.
In turn, having a non-NULL dp->bridge_dev when there is no offloading
support makes the following things go wrong:
- dsa_default_offload_fwd_mark make the wrong decision in setting
skb->offload_fwd_mark. It should set skb->offload_fwd_mark = 0 for
ports that don't offload the bridge, which should instruct the bridge
to forward in software. But this does not happen, dp->bridge_dev is
incorrectly set to point to the bridge, so the bridge is told that
packets have been forwarded in hardware, which they haven't.
- switchdev objects (MDBs, VLANs) should not be offloaded by ports that
don't offload the bridge. Standalone ports should behave as packet-in,
packet-out and the bridge should not be able to manipulate the pvid of
the port, or tag stripping on egress, or ingress filtering. This
should already work fine because dsa_slave_port_obj_add has:
case SWITCHDEV_OBJ_ID_PORT_VLAN:
if (!dsa_port_offloads_bridge_port(dp, obj->orig_dev))
return -EOPNOTSUPP;
err = dsa_slave_vlan_add(dev, obj, extack);
but since dsa_port_offloads_bridge_port works based on dp->bridge_dev,
this is again sabotaging us.
All the above work in case the port has an unoffloaded LAG interface, so
this is well exercised code, we should apply it for plain unoffloaded
bridge ports too.
Reported-by: Alvin Šipraga <alsi@bang-olufsen.dk>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For ports that have a NULL dp->bridge_dev, dsa_port_to_bridge_port()
also returns NULL as expected.
Issue #1 is that we are performing a NULL pointer dereference on brport_dev.
Issue #2 is that these are ports on which switchdev_bridge_port_offload
has not been called, so we should not call switchdev_bridge_port_unoffload
on them either.
Both issues are addressed by checking against a NULL brport_dev in
dsa_port_pre_bridge_leave and exiting early.
Fixes: 2f5dc00f7a ("net: bridge: switchdev: let drivers inform which bridge ports are offloaded")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Right now, cross-tree bridging setups work somewhat by mistake.
In the case of cross-tree bridging with sja1105, all switch instances
need to agree upon a common VLAN ID for forwarding a packet that belongs
to a certain bridging domain.
With TX forwarding offload, the VLAN ID is the bridge VLAN for
VLAN-aware bridging, and the tag_8021q TX forwarding offload VID
(a VLAN which has non-zero VBID bits) for VLAN-unaware bridging.
The VBID for VLAN-unaware bridging is derived from the dp->bridge_num
value calculated by DSA independently for each switch tree.
If ports from one tree join one bridge, and ports from another tree join
another bridge, DSA will assign them the same bridge_num, even though
the bridges are different. If cross-tree bridging is supported, this
is an issue.
Modify DSA to calculate the bridge_num globally across all switch trees.
This has the implication for a driver that the dp->bridge_num value that
DSA will assign to its ports might not be contiguous, if there are
boards with multiple DSA drivers instantiated. Additionally, all
bridge_num values eat up towards each switch's
ds->num_fwd_offloading_bridges maximum, which is potentially unfortunate,
and can be seen as a limitation introduced by this patch. However, that
is the lesser evil for now.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for tag_sja1105 running on non-sja1105 DSA ports, by making
sure that every time we dereference dp->priv, we check the switch's
dsa_switch_ops (otherwise we access a struct sja1105_port structure that
is in fact something else).
This adds an unconditional build-time dependency between sja1105 being
built as module => tag_sja1105 must also be built as module. This was
there only for PTP before.
Some sane defaults must also take place when not running on sja1105
hardware. These are:
- sja1105_xmit_tpid: the sja1105 driver uses different VLAN protocols
depending on VLAN awareness and switch revision (when an encapsulated
VLAN must be sent). Default to 0x8100.
- sja1105_rcv_meta_state_machine: this aggregates PTP frames with their
metadata timestamp frames. When running on non-sja1105 hardware, don't
do that and accept all frames unmodified.
- sja1105_defer_xmit: calls sja1105_port_deferred_xmit in sja1105_main.c
which writes a management route over SPI. When not running on sja1105
hardware, bypass the SPI write and send the frame as-is.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
During the development of the blamed patch, the "bool broadcast"
argument of dsa_port_tag_8021q_vlan_{add,del} was originally called
"bool local", and the meaning was the exact opposite.
Due to a rookie mistake where the patch was modified at the last minute
without retesting, the instances of dsa_port_tag_8021q_vlan_{add,del}
are called with the wrong values. During setup and teardown, cross-chip
notifiers should not be broadcast to all DSA trees, while during
bridging, they should.
Fixes: 724395f4dc ("net: dsa: tag_8021q: don't broadcast during setup/teardown")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, on my board with multiple sja1105 switches in disjoint trees
described in commit f66a6a69f9 ("net: dsa: permit cross-chip bridging
between all trees in the system"), rebooting the board triggers the
following benign warnings:
[ 12.345566] sja1105 spi2.0: port 0 failed to notify tag_8021q VLAN 1088 deletion: -ENOENT
[ 12.353804] sja1105 spi2.0: port 0 failed to notify tag_8021q VLAN 2112 deletion: -ENOENT
[ 12.362019] sja1105 spi2.0: port 1 failed to notify tag_8021q VLAN 1089 deletion: -ENOENT
[ 12.370246] sja1105 spi2.0: port 1 failed to notify tag_8021q VLAN 2113 deletion: -ENOENT
[ 12.378466] sja1105 spi2.0: port 2 failed to notify tag_8021q VLAN 1090 deletion: -ENOENT
[ 12.386683] sja1105 spi2.0: port 2 failed to notify tag_8021q VLAN 2114 deletion: -ENOENT
Basically switch 1 calls dsa_tag_8021q_unregister, and switch 1's TX and
RX VLANs cannot be found on switch 2's CPU port.
But why would switch 2 even attempt to delete switch 1's TX and RX
tag_8021q VLANs from its CPU port? Well, because we use dsa_broadcast,
and it is supposed that it had added those VLANs in the first place
(because in dsa_port_tag_8021q_vlan_match, all CPU ports match
regardless of their tree index or switch index).
The two trees probe asynchronously, and when switch 1 probed, it called
dsa_broadcast which did not notify the tree of switch 2, because that
didn't probe yet. But during unbind, switch 2's tree _is_ probed, so it
_is_ notified of the deletion.
Before jumping to introduce a synchronization mechanism between the
probing across disjoint switch trees, let's take a step back and see
whether we _need_ to do that in the first place.
The RX and TX VLANs of switch 1 would be needed on switch 2's CPU port
only if switch 1 and 2 were part of a cross-chip bridge. And
dsa_tag_8021q_bridge_join takes care precisely of that (but if probing
was synchronous, the bridge_join would just end up bumping the VLANs'
refcount, because they are already installed by the setup path).
Since by the time the ports are bridged, all DSA trees are already set
up, and we don't need the tag_8021q VLANs of one switch installed on the
other switches during probe time, the answer is that we don't need to
fix the synchronization issue.
So make the setup and teardown code paths call dsa_port_notify, which
notifies only the local tree, and the bridge code paths call
dsa_broadcast, which let the other trees know as well.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently this error message does not say a lot:
[ 32.693498] DSA: failed to notify tag_8021q VLAN deletion: -ENOENT
[ 32.699725] DSA: failed to notify tag_8021q VLAN deletion: -ENOENT
[ 32.705931] DSA: failed to notify tag_8021q VLAN deletion: -ENOENT
[ 32.712139] DSA: failed to notify tag_8021q VLAN deletion: -ENOENT
[ 32.718347] DSA: failed to notify tag_8021q VLAN deletion: -ENOENT
[ 32.724554] DSA: failed to notify tag_8021q VLAN deletion: -ENOENT
but in this form, it is immediately obvious (at least to me) what the
problem is, even without further looking at the code:
[ 12.345566] sja1105 spi2.0: port 0 failed to notify tag_8021q VLAN 1088 deletion: -ENOENT
[ 12.353804] sja1105 spi2.0: port 0 failed to notify tag_8021q VLAN 2112 deletion: -ENOENT
[ 12.362019] sja1105 spi2.0: port 1 failed to notify tag_8021q VLAN 1089 deletion: -ENOENT
[ 12.370246] sja1105 spi2.0: port 1 failed to notify tag_8021q VLAN 2113 deletion: -ENOENT
[ 12.378466] sja1105 spi2.0: port 2 failed to notify tag_8021q VLAN 1090 deletion: -ENOENT
[ 12.386683] sja1105 spi2.0: port 2 failed to notify tag_8021q VLAN 2114 deletion: -ENOENT
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Create a similar helper for locating the offset to the DSA header
relative to skb->data, and make the existing EtherType header taggers to
use it.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
It seems that protocol tagging driver writers are always surprised about
the formula they use to reach their EtherType header on RX, which
becomes apparent from the fact that there are comments in multiple
drivers that mention the same information.
Create a helper that returns a void pointer to skb->data - 2, as well as
centralize the explanation why that is the case.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Hide away the memmove used by DSA EtherType header taggers to shift the
MAC SA and DA to the left to make room for the header, after they've
called skb_push(). The call to skb_push() is still left explicit in
drivers, to be symmetric with dsa_strip_etype_header, and because not
all callers can be refactored to do it (for example, brcm_tag_xmit_ll
has common code for a pre-Ethernet DSA tag and an EtherType DSA tag).
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
All header taggers open-code a memmove that is fairly not all that
obvious, and we can hide the details behind a helper function, since the
only thing specific to the driver is the length of the header tag.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The blamed commit added a new field to struct switchdev_notifier_fdb_info,
but did not make sure that all call paths set it to something valid.
For example, a switchdev driver may emit a SWITCHDEV_FDB_ADD_TO_BRIDGE
notifier, and since the 'is_local' flag is not set, it contains junk
from the stack, so the bridge might interpret those notifications as
being for local FDB entries when that was not intended.
To avoid that now and in the future, zero-initialize all
switchdev_notifier_fdb_info structures created by drivers such that all
newly added fields to not need to touch drivers again.
Fixes: 2c4eca3ef7 ("net: bridge: switchdev: include local flag in FDB notifications")
Reported-by: Ido Schimmel <idosch@idosch.org>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Tested-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Reviewed-by: Karsten Graul <kgraul@linux.ibm.com>
Link: https://lore.kernel.org/r/20210810115024.1629983-1-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
All kernel devlink implementations call to devlink_alloc() during
initialization routine for specific device which is used later as
a parent device for devlink_register().
Such late device assignment causes to the situation which requires us to
call to device_register() before setting other parameters, but that call
opens devlink to the world and makes accessible for the netlink users.
Any attempt to move devlink_register() to be the last call generates the
following error due to access to the devlink->dev pointer.
[ 8.758862] devlink_nl_param_fill+0x2e8/0xe50
[ 8.760305] devlink_param_notify+0x6d/0x180
[ 8.760435] __devlink_params_register+0x2f1/0x670
[ 8.760558] devlink_params_register+0x1e/0x20
The simple change of API to set devlink device in the devlink_alloc()
instead of devlink_register() fixes all this above and ensures that
prior to call to devlink_register() everything already set.
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Drivers that support both the toggling of address learning and dynamic
FDB flushing (mv88e6xxx, b53, sja1105) currently need to fast-age a port
twice when it leaves a bridge:
- once, when del_nbp() calls br_stp_disable_port() which puts the port
in the BLOCKING state
- twice, when dsa_port_switchdev_unsync_attrs() calls
dsa_port_clear_brport_flags() which disables address learning
The knee-jerk reaction might be to say "dsa_port_clear_brport_flags does
not need to fast-age the port at all", but the thing is, we still need
both code paths to flush the dynamic FDB entries in different situations.
When a DSA switch port leaves a bonding/team interface that is (still) a
bridge port, no del_nbp() will be called, so we rely on
dsa_port_clear_brport_flags() function to restore proper standalone port
functionality with address learning disabled.
So the solution is just to avoid double the work when both code paths
are called in series. Luckily, DSA already caches the STP port state, so
we can skip flushing the dynamic FDB when we disable address learning
and the STP state is one where no address learning takes place at all.
Under that condition, not flushing the FDB is safe because there is
supposed to not be any dynamic FDB entry at all (they were flushed
during the transition towards that state, and none were learned in the
meanwhile).
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 39f3210154 ("net: dsa: don't fast age standalone ports")
assumed that all standalone ports disable address learning, but if the
switch driver implements .port_fast_age but not .port_bridge_flags (like
ksz9477, ksz8795, lantiq_gswip, lan9303), then that might not actually
be true.
So whereas before, the bridge temporarily walking us through the
BLOCKING STP state meant that the standalone ports had a checkpoint to
flush their baggage and start fresh when they join a bridge, after that
commit they no longer do.
Restore the old behavior for these drivers by checking if the switch can
toggle address learning. If it can't, disregard the "do_fast_age"
argument and unconditionally perform fast ageing on STP state changes.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, when DSA performs fast ageing on a port, 'bridge fdb' shows
us that the 'self' entries (corresponding to the hardware bridge, as
printed by dsa_slave_fdb_dump) are deleted, but the 'master' entries
(corresponding to the software bridge) aren't.
Indeed, searching through the bridge driver, neither the
brport_attr_learning handler nor the IFLA_BRPORT_LEARNING handler call
br_fdb_delete_by_port. However, br_stp_disable_port does, which is one
of the paths which DSA uses to trigger a fast ageing process anyway.
There is, however, one other very promising caller of
br_fdb_delete_by_port, and that is the bridge driver's handler of the
SWITCHDEV_FDB_FLUSH_TO_BRIDGE atomic notifier. Currently the s390/qeth
HiperSockets card driver is the only user of this.
I can't say I understand that driver's architecture or interaction with
the bridge, but it appears to not be a switchdev driver in the traditional
sense of the word. Nonetheless, the mechanism it provides is a useful
way for DSA to express the fact that it performs fast ageing too, in a
way that does not change the existing behavior for other drivers.
Cc: Alexandra Winter <wintera@linux.ibm.com>
Cc: Julian Wiedmann <jwi@linux.ibm.com>
Cc: Roopa Prabhu <roopa@nvidia.com>
Cc: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On topology changes, stations that were dynamically learned on ports
that are no longer part of the active topology must be flushed - this is
described by clause "17.11 Updating learned station location information"
of IEEE 802.1D-2004.
However, when address learning on the bridge port is turned off in the
first place, there is nothing to flush, so skip a potentially expensive
operation.
We can finally do this now since DSA is aware of the learning state of
its bridged ports.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently DSA leaves it down to device drivers to fast age the FDB on a
port when address learning is disabled on it. There are 2 reasons for
doing that in the first place:
- when address learning is disabled by user space, through
IFLA_BRPORT_LEARNING or the brport_attr_learning sysfs, what user
space typically wants to achieve is to operate in a mode with no
dynamic FDB entry on that port. But if the port is already up, some
addresses might have been already learned on it, and it seems silly to
wait for 5 minutes for them to expire until something useful can be
done.
- when a port leaves a bridge and becomes standalone, DSA turns off
address learning on it. This also has the nice side effect of flushing
the dynamically learned bridge FDB entries on it, which is a good idea
because standalone ports should not have bridge FDB entries on them.
We let drivers manage fast ageing under this condition because if DSA
were to do it, it would need to track each port's learning state, and
act upon the transition, which it currently doesn't.
But there are 2 reasons why doing it is better after all:
- drivers might get it wrong and not do it (see b53_port_set_learning)
- we would like to flush the dynamic entries from the software bridge
too, and letting drivers do that would be another pain point
So track the port learning state and trigger a fast age process
automatically within DSA.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
DSA drives the procedure to flush dynamic FDB entries from a port based
on the change of STP state: whenever we go from a state where address
learning is enabled (LEARNING, FORWARDING) to a state where it isn't
(LISTENING, BLOCKING, DISABLED), we need to flush the existing dynamic
entries.
However, there are cases when this is not needed. Internally, when a
DSA switch interface is not under a bridge, DSA still keeps it in the
"FORWARDING" STP state. And when that interface joins a bridge, the
bridge will meticulously iterate that port through all STP states,
starting with BLOCKING and ending with FORWARDING. Because there is a
state transition from the standalone version of FORWARDING into the
temporary BLOCKING bridge port state, DSA calls the fast age procedure.
Since commit 5e38c15856 ("net: dsa: configure better brport flags when
ports leave the bridge"), DSA asks standalone ports to disable address
learning. Therefore, there can be no dynamic FDB entries on a standalone
port. Therefore, it does not make sense to flush dynamic FDB entries on
one.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 08cc83cc7f ("net: dsa: add support for BRIDGE_MROUTER
attribute") added an option for users to turn off multicast flooding
towards the CPU if they turn off the IGMP querier on a bridge which
already has enslaved ports (echo 0 > /sys/class/net/br0/bridge/multicast_router).
And commit a8b659e7ff ("net: dsa: act as passthrough for bridge port flags")
simply papered over that issue, because it moved the decision to flood
the CPU with multicast (or not) from the DSA core down to individual drivers,
instead of taking a more radical position then.
The truth is that disabling multicast flooding to the CPU is simply
something we are not prepared to do now, if at all. Some reasons:
- ICMP6 neighbor solicitation messages are unregistered multicast
packets as far as the bridge is concerned. So if we stop flooding
multicast, the outside world cannot ping the bridge device's IPv6
link-local address.
- There might be foreign interfaces bridged with our DSA switch ports
(sending a packet towards the host does not necessarily equal
termination, but maybe software forwarding). So if there is no one
interested in that multicast traffic in the local network stack, that
doesn't mean nobody is.
- PTP over L4 (IPv4, IPv6) is multicast, but is unregistered as far as
the bridge is concerned. This should reach the CPU port.
- The switch driver might not do FDB partitioning. And since we don't
even bother to do more fine-grained flood disabling (such as "disable
flooding _from_port_N_ towards the CPU port" as opposed to "disable
flooding _from_any_port_ towards the CPU port"), this breaks standalone
ports, or even multiple bridges where one has an IGMP querier and one
doesn't.
Reverting the logic makes all of the above work.
Fixes: a8b659e7ff ("net: dsa: act as passthrough for bridge port flags")
Fixes: 08cc83cc7f ("net: dsa: add support for BRIDGE_MROUTER attribute")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Qingfang points out that when a bridge with the default settings is
created and a port joins it:
ip link add br0 type bridge
ip link set swp0 master br0
DSA calls br_multicast_router() on the bridge to see if the br0 device
is a multicast router port, and if it is, it enables multicast flooding
to the CPU port, otherwise it disables it.
If we look through the multicast_router_show() sysfs or at the
IFLA_BR_MCAST_ROUTER netlink attribute, we see that the default mrouter
attribute for the bridge device is "1" (MDB_RTR_TYPE_TEMP_QUERY).
However, br_multicast_router() will return "0" (MDB_RTR_TYPE_DISABLED),
because an mrouter port in the MDB_RTR_TYPE_TEMP_QUERY state may not be
actually _active_ until it receives an actual IGMP query. So, the
br_multicast_router() function should really have been called
br_multicast_router_active() perhaps.
When/if an IGMP query is received, the bridge device will transition via
br_multicast_mark_router() into the active state until the
ip4_mc_router_timer expires after an multicast_querier_interval.
Of course, this does not happen if the bridge is created with an
mcast_router attribute of "2" (MDB_RTR_TYPE_PERM).
The point is that in lack of any IGMP query messages, and in the default
bridge configuration, unregistered multicast packets will not be able to
reach the CPU port through flooding, and this breaks many use cases
(most obviously, IPv6 ND, with its ICMP6 neighbor solicitation multicast
messages).
Leave the multicast flooding setting towards the CPU port down to a driver
level decision.
Fixes: 010e269f91 ("net: dsa: sync up switchdev objects and port attributes when joining the bridge")
Reported-by: DENG Qingfang <dqfext@gmail.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
TX timestamps are sent by SJA1110 as Ethernet packets containing
metadata, so they are received by the tagging driver but must be
processed by the switch driver - the one that is stateful since it
keeps the TX timestamp queue.
This means that there is an sja1110_process_meta_tstamp() symbol
exported by the switch driver which is called by the tagging driver.
There is a shim definition for that function when the switch driver is
not compiled, which does nothing, but that shim is not effective when
the tagging protocol driver is built-in and the switch driver is a
module, because built-in code cannot call symbols exported by modules.
So add an optional dependency between the tagger and the switch driver,
if PTP support is enabled in the switch driver. If PTP is not enabled,
sja1110_process_meta_tstamp() will translate into the shim "do nothing
with these meta frames" function.
Fixes: 566b18c8b7 ("net: dsa: sja1105: implement TX timestamping for SJA1110")
Reported-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vladimir Oltean
Christophe JAILLET
Alvin Šipraga
Andrew Lunn
Linus Walleij
Jakub Kicinski
Leon Romanovsky