On many laptops setting a different LPM policy then unknown /
max_performance can lead to power-savings of 1.0 - 1.5 Watts (when idle).
Modern ultrabooks idle around 6W (at 50% screen brightness), 1.0 - 1.5W
is a significant chunk of this.
There are some performance / latency costs to enabling LPM by default,
so it is desirable to make it possible to set a different LPM policy
for mobile / laptop variants of chipsets / "South Bridges" vs their
desktop / server counterparts. Also enabling LPM by default is not
entirely without risk of regressions. At least min_power is known to
cause issues with some disks, including some reports of data corruption.
This commits adds a new ahci.mobile_lpm_policy kernel cmdline option,
which defaults to a new SATA_MOBILE_LPM_POLICY Kconfig option so that
Linux distributions can choose to set a LPM policy for mobile chipsets
by default.
The reason to have both a kernel cmdline option and a Kconfig default
value for it, is to allow easy overriding of the default to allow
trouble-shooting without needing to rebuild the kernel.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Add PCI ids for Intel Bay Trail, Cherry Trail and Apollo Lake AHCI
SATA controllers. This commit is a preparation patch for allowing a
different default sata link powermanagement policy for mobile chipsets.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Intel uses different SATA PCI ids for the Desktop and Mobile SKUs of their
chipsets. For older models the comment describing which chipset the PCI id
is for, aksi indicates when we're dealing with a mobile SKU. Extend the
comments for recent chipsets to also indicate mobile SKUs.
The information this commit adds comes from Intel's chipset datasheets.
This commit is a preparation patch for allowing a different default
sata link powermanagement policy for mobile chipsets.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
During hotplug, it is possible for 6Gbps link speed to be limited all
the way down to 1.5 Gbps which may lead to a slower link speed when
drive is re-connected.
This behavior has been seen on a Intel Lewisburg SATA controller
(8086:a1d2) with HGST HUH728080ALE600 drive where SATA link speed was
limited to 1.5 Gbps and when re-connected the link came up 3.0 Gbps.
This patch was retested on above configuration and showed the
hotplugged link to come back online at max speed (6Gbps). I did not
see the downgrade when testing on Intel C600/X79, but retested patched
linux-4.14-rc5 kernel and didn't see any side effects from this
change. Also, successfully retested hotplug on port multiplier 3Gbps
link.
tj: Minor comment updates.
Signed-off-by: David Milburn <dmilburn@redhat.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
The driver name "ahci" is already used by the ahci platform driver.
This leads to the following error:
Error: Driver 'ahci' is already registered, aborting...
Change the name to ahci-mtk to fix this.
Signed-off-by: Matthias Brugger <mbrugger@suse.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
These PP2C and PP3C registers control the configuration of the PHY
control OOB timing for the COMINIT/COMWAKE parameters respectively
for sata port. Overwrite default values with calculated ones to get
better OOB timing.
Signed-off-by: Tang Yuantian <andy.tang@nxp.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Make these pdc2027x_*_timing structures const as it is never modified.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Here, The function pdc_hardware_init always return zero. So it is not
necessary to check its return value.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Pull libata updates from Tejun Heo:
"Nothing too interesting or alarming. Other than a new power saving
mode addition to ahci and crash fix on a tracepoint, all changes are
trivial or device-specific"
* 'for-4.15' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata: (22 commits)
ahci: imx: Handle increased read failures for IMX53 temperature sensor in low frequency mode.
ata: sata_dwc_460ex: Propagate platform device ID to DMA driver
ata: fixes kernel crash while tracing ata_eh_link_autopsy event
ata: pata_pdc2027x: Fix space before '[' error.
libata: fix spelling mistake: 'ambigious' -> 'ambiguous'
ata: ceva: Add SMMU support for SATA IP
ata: ceva: Correct the suspend and resume logic for SATA
ata: ceva: Correct the AXI bus configuration for SATA ports
ata: ceva: Add CCI support for SATA if CCI is enabled
ata: ceva: Make RxWaterMark value as module parameter
ata: ceva: Disable Device Sleep capability
ata: ceva: Add gen 3 mode support in driver
ata: ceva: Move sata port phy oob settings to device-tree
devicetree: bindings: Add sata port phy config parameters in ahci-ceva
ata: mark expected switch fall-throughs
ata: sata_mv: remove a redundant assignment to pointer ehi
ahci: Add support for Cavium's fifth generation SATA controller
ata: sata_rcar: Use of_device_get_match_data() helper
libata: make ata_port_type const
libata: make static arrays const, reduces object code size
...
Pull timer updates from Thomas Gleixner:
"Yet another big pile of changes:
- More year 2038 work from Arnd slowly reaching the point where we
need to think about the syscalls themself.
- A new timer function which allows to conditionally (re)arm a timer
only when it's either not running or the new expiry time is sooner
than the armed expiry time. This allows to use a single timer for
multiple timeout requirements w/o caring about the first expiry
time at the call site.
- A new NMI safe accessor to clock real time for the printk timestamp
work. Can be used by tracing, perf as well if required.
- A large number of timer setup conversions from Kees which got
collected here because either maintainers requested so or they
simply got ignored. As Kees pointed out already there are a few
trivial merge conflicts and some redundant commits which was
unavoidable due to the size of this conversion effort.
- Avoid a redundant iteration in the timer wheel softirq processing.
- Provide a mechanism to treat RTC implementations depending on their
hardware properties, i.e. don't inflict the write at the 0.5
seconds boundary which originates from the PC CMOS RTC to all RTCs.
No functional change as drivers need to be updated separately.
- The usual small updates to core code clocksource drivers. Nothing
really exciting"
* 'timers-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (111 commits)
timers: Add a function to start/reduce a timer
pstore: Use ktime_get_real_fast_ns() instead of __getnstimeofday()
timer: Prepare to change all DEFINE_TIMER() callbacks
netfilter: ipvs: Convert timers to use timer_setup()
scsi: qla2xxx: Convert timers to use timer_setup()
block/aoe: discover_timer: Convert timers to use timer_setup()
ide: Convert timers to use timer_setup()
drbd: Convert timers to use timer_setup()
mailbox: Convert timers to use timer_setup()
crypto: Convert timers to use timer_setup()
drivers/pcmcia: omap1: Fix error in automated timer conversion
ARM: footbridge: Fix typo in timer conversion
drivers/sgi-xp: Convert timers to use timer_setup()
drivers/pcmcia: Convert timers to use timer_setup()
drivers/memstick: Convert timers to use timer_setup()
drivers/macintosh: Convert timers to use timer_setup()
hwrng/xgene-rng: Convert timers to use timer_setup()
auxdisplay: Convert timers to use timer_setup()
sparc/led: Convert timers to use timer_setup()
mips: ip22/32: Convert timers to use timer_setup()
...
Extended testing has shown that the imx ahci driver sometimes requires
more than the 100 attempts currently alotted in the driver to perform a
successful temperature reading when running at minimum (throttled) CPU
frequency.
Debugging suggests that the read cycle can take 160 attempts (which given
that the driver averages 80 readings from the ADC equates to one failure
on each read).
Increase the attempt limit to 200 in order to greatly reduce the
likelihood of the driver failing to perform a temperature reading,
especially at low CPU frequency.
Signed-off-by: Egor Starkov <egor.starkov@ge.com>
Signed-off-by: Martyn Welch <martyn.welch@collabora.co.uk>
Signed-off-by: Tejun Heo <tj@kernel.org>
Propagate platform device ID to DMA driver to distinguish relationship
between DMA and SATA instances.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
When tracing ata link error event, the kernel crashes when the disk is
removed due to NULL pointer access by trace_ata_eh_link_autopsy API.
This occurs as the dev is NULL when the disk disappeared. This patch
fixes this crash by calling trace_ata_eh_link_autopsy only if "dev"
is not NULL.
v2 changes:
Removed direct passing "link" pointer instead of "dev" in trace API.
Signed-off-by: Rameshwar Prasad Sahu <rsahu@apm.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Fixes: 255c03d15a ("libata: Add tracepoints")
Cc: stable@vger.kernel.org # v4.1+
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
AXI master interface in CEVA AHCI controller requires two unique
Write/Read ID tags per port. This is because, ahci controller uses
different AXI ID[3:0] bits for identifying non-data transfers(like
reading descriptors, updating PRD tables, etc) and data transfers
(like sending/receiving FIS).To make SMMU work with SATA we need to
add correct SMMU stream id for SATA. SMMU stream id for SATA is
determined based on the AXI ID[1:0] as shown below
SATA SMMU ID = <TBU number>, 0011, 00, 00, AXI ID[1:0]
Note: SATA in ZynqMp uses TBU1 so TBU number = 0x1, so
SMMU ID = 001, 0011, 00, 00, AXI ID[1:0]
Since we have four different AXI ID[3:0] (2 for port0 & 2 for port1
as said above) we get four different SMMU stream id's combinations
for SATA. These AXI ID can be configured using PAXIC register.
In this patch we assumed the below AXI ID values
Read ID/ Write ID for Non-Data Port0 transfers = 0
Read ID/ Write ID for Data Port0 transfers = 1
Read ID/ Write ID for Non-Data Port1 transfers = 2
Read ID/ Write ID for Data Port1 transfers = 3
Based on the above values,SMMU stream ID's for SATA will be 0x4c0 &
0x4c1 for PORT0, 0x4c2 & 0x4c3 for PORT1. These values needed to be
added to iommus dts property. This patch does the same.
Signed-off-by: Anurag Kumar Vulisha <anuragku@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
The present suspend code disables the port interrupts
and stops the HBA. On resume it enables the interrupts and HBA.
This works fine until the FPD power domain is not off.
If FPD is off then the ceva vendor specific configurations like
OOB, AXI settings are lost, they need to be re-programmed and
also since SERDES is also in FPD , SATA lane phy init needs to
be called again (which is not happening in the present sequence)
Because of this incorrect sequence SATA fails to work on resume.
This patch corrects the code to make Suspend & Resume work in normal
and FPD off cases.
Signed-off-by: Anurag Kumar Vulisha <anuragku@xilinx.com>
Reviewed-by: Shubhrajyoti Datta <shubhraj@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Previously PAXIC register was programmed before configuring PCFG
register. PCFG should be programmed with the address of the port
for which PAXIC should be configured for.
This was not happening before, so only one port PAXIC was written
correctly and the other port was having wrong value.
This patch moves the PXAIC register write after configuring PCFG,
doing so will correct the axi bus settings for sata port0 & port1.
Signed-off-by: Anurag Kumar Vulisha <anuragku@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
This patch adds support for CCI in SATA controller if CCI is
enabled in design. This patch will add CCI settings for SATA
if "dma-coherent" dts property is added.
Signed-off-by: Anurag Kumar Vulisha <anuragku@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
This patch updates the driver to make Rx Fifo water mark value
as a module parameter.
Signed-off-by: Anurag Kumar Vulisha <anuragku@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Since CEVA controller does not support Device Sleep capability,
we need to clear that feature by clearing the DEVSLP bit in word78
of IDENTIFY DEVICE data. This patch does the same.
Signed-off-by: Anurag Kumar Vulisha <anuragku@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
This patch sets gen 3 mode as default mode in ahci_ceva driver.
Signed-off-by: Anurag Kumar Vulisha <anuragku@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
In SATA Speed negotiation happens with OOB(Out of Band) signals. These OOB
signal timing values are configured through vendor specific registers in the
SATA controller. These OOB timings depends on the generator and detector clock
frequency, which varies from board to board (ex: ep108 and zc1751 has different
clock frequencies).
To avoid maintaing these OOB settings in the driver, it is better to move these
settings to the device-tree node and read from the device-tree.
This patch does the same.
Signed-off-by: Anurag Kumar Vulisha <anuragku@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
In cases where a "drop through" comment was already in place, I replaced
it with a proper "fall through" comment, which is what GCC is expecting
to find.
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
The pointer ehi is being assigned to a value that is never read
and is redundant. Clean up the code and move the ehi declaration
and initialization to the code block where it is used. Cleans up
clang warning: Value stored to 'ehi' is never read
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
In preparation for unconditionally passing the struct timer_list pointer to
all timer callbacks, switch to using the new timer_setup() and from_timer()
to pass the timer pointer explicitly. Adds a pointer back to link
structure.
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Tejun Heo <tj@kernel.org>
Cc: linux-ide@vger.kernel.org
Link: https://lkml.kernel.org/r/20171016215658.GA101965@beast
In preparation for unconditionally passing the struct timer_list pointer to
all timer callbacks, switch to using the new timer_setup() and from_timer()
to pass the timer pointer explicitly.
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Tejun Heo <tj@kernel.org>
Cc: linux-ide@vger.kernel.org
Link: https://lkml.kernel.org/r/20171005004842.GA23011@beast
This patch adds support for Cavium's fifth generation SATA controller.
It is an on-chip controller and complies with AHCI 1.3.1. As the
controller uses 64-bit addresses it cannot use the standard AHCI BAR5
and so uses BAR4.
Signed-off-by: Radha Mohan Chintakuntla <rchintakuntla@cavium.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Use the of_device_get_match_data() helper instead of open coding.
Note that the sata_rcar driver is used with DT only, so there's always a
valid match.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
ahci_pci_reset_controller() calls ahci_reset_controller(), which may
fail, but ignores the result code and always returns success. This
may result in failures like below
ahci 0000:02:00.0: version 3.0
ahci 0000:02:00.0: enabling device (0000 -> 0003)
ahci 0000:02:00.0: SSS flag set, parallel bus scan disabled
ahci 0000:02:00.0: controller reset failed (0xffffffff)
ahci 0000:02:00.0: failed to stop engine (-5)
... repeated many times ...
ahci 0000:02:00.0: failed to stop engine (-5)
Unable to handle kernel paging request at virtual address ffff0000093f9018
...
PC is at ahci_stop_engine+0x5c/0xd8 [libahci]
LR is at ahci_deinit_port.constprop.12+0x1c/0xc0 [libahci]
...
[<ffff000000a17014>] ahci_stop_engine+0x5c/0xd8 [libahci]
[<ffff000000a196b4>] ahci_deinit_port.constprop.12+0x1c/0xc0 [libahci]
[<ffff000000a197d8>] ahci_init_controller+0x80/0x168 [libahci]
[<ffff000000a260f8>] ahci_pci_init_controller+0x60/0x68 [ahci]
[<ffff000000a26f94>] ahci_init_one+0x75c/0xd88 [ahci]
[<ffff000008430324>] local_pci_probe+0x3c/0xb8
[<ffff000008431728>] pci_device_probe+0x138/0x170
[<ffff000008585e54>] driver_probe_device+0x2dc/0x458
[<ffff0000085860e4>] __driver_attach+0x114/0x118
[<ffff000008583ca8>] bus_for_each_dev+0x60/0xa0
[<ffff000008585638>] driver_attach+0x20/0x28
[<ffff0000085850b0>] bus_add_driver+0x1f0/0x2a8
[<ffff000008586ae0>] driver_register+0x60/0xf8
[<ffff00000842f9b4>] __pci_register_driver+0x3c/0x48
[<ffff000000a3001c>] ahci_pci_driver_init+0x1c/0x1000 [ahci]
[<ffff000008083918>] do_one_initcall+0x38/0x120
where an obvious hardware level failure results in an unnecessary 15 second
delay and a subsequent crash.
So record the result code of ahci_reset_controller() and relay it, rather
than ignoring it.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Tejun Heo <tj@kernel.org>
Make this const as it is only stored in the const field of a device
structure. Make the declaration in header const too.
Structure found using Coccinelle and changes done by hand.
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Don't populate const arrayis on the stack, instead make them static.
Makes the object code smaller by over 260 bytes:
Before:
text data bss dec hex filename
64864 5948 4128 74940 124bc drivers/ata/libata-scsi.o
After:
text data bss dec hex filename
64183 6364 4128 74675 123b3 drivers/ata/libata-scsi.o
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Fujitsu-Siemens Lifebook S6120 misdetects the cable type for some
drives. The problematic one in this case is an mSATA SSD hooked up via a
mSATA->PATA bridge. With regular hard disks the detection seems to work
correctly.
Strangely an older Lifebook model (S6020) detects the cable as 80c
with the mSATA SSD, even if using the exact same flex cable.
Cc: Tejun Heo <tj@kernel.org>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
pio is initialized and the data is never read, instead it is almost
immediately being updated to a new value. Fix this by removing the
initialization.
Detected by scan-build:
"warning: Value stored to 'pio' during its initialization is never read"
Fixes: 669a5db411 ("[libata] Add a bunch of PATA drivers")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
As described by Matthew Garret quite a while back:
https://mjg59.dreamwidth.org/34868.html
Intel CPUs starting with the Haswell generation need SATA links to power
down for the "package" part of the CPU to reach low power-states like
PC7 / P8 which bring a significant power-saving with them.
The default max_performance lpm policy does not allow for these high
PC states, both the medium_power and min_power policies do allow this.
The min_power policy saves significantly more power, but there are some
reports of some disks / SSDs not liking min_power leading to system
crashes and in some cases even data corruption has been reported.
Matthew has found a document documenting the default settings of
Intel's IRST Windows driver with which most laptops ship:
https://www-ssl.intel.com/content/dam/doc/reference-guide/sata-devices-implementation-recommendations.pdf
Matthew wrote a patch changing med_power to match those defaults, but
that never got anywhere as some people where reporting issues with the
patch-set that patch was a part of.
This commit is another attempt to make the default IRST driver settings
available under Linux, but instead of changing medium_power and
potentially introducing regressions, this commit adds a new
med_power_with_dipm setting which is identical to the existing
medium_power accept that it enables dipm on top, which makes it match
the Windows IRST driver settings, which should hopefully be safe to
use on most devices.
The med_power_with_dipm setting is close to min_power, except that:
a) It does not use host-initiated slumber mode (ASP not set),
but it does allow device-initiated slumber
b) It does not enable DevSlp mode
On my T440s test laptop I get the following power savings when idle:
medium_power 0.9W
med_power_with_dipm 1.2W
min_power 1.2W
Suggested-by: Matthew Garrett <mjg59@srcf.ucam.org>
Cc: Matthew Garrett <mjg59@srcf.ucam.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
gcc-7 warns about the result of a constant multiplication used as
a boolean:
drivers/ata/libata-core.c: In function 'ata_timing_quantize':
drivers/ata/libata-core.c:3164:30: warning: '*' in boolean context, suggest '&&' instead [-Wint-in-bool-context]
This slightly rearranges the macro to simplify the code and avoid
the warning at the same time.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Tejun Heo <tj@kernel.org>
Pull libata updates from Tejun Heo:
"Except for the ahci fix that fixes a boot issue, nothing major in this
pull request. Some new platform controller support and device specific
changes"
* 'for-4.14' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata:
libata: zpodd: make arrays cdb static, reduces object code size
ahci: don't use MSI for devices with the silly Intel NVMe remapping scheme
dt-bindings: ata: add DT bindings for MediaTek SATA controller
ata: mediatek: add support for MediaTek SATA controller
pata_octeon_cf: use of_property_read_{bool|u32}()
cs5536: add support for IDE controller variant
ata: sata_gemini: Introduce explicit IDE pin control
ata: sata_gemini: Retire custom pin control
ata: ahci_platform: Add shutdown handler
ata: sata_gemini: explicitly request exclusive reset control
ata: Drop unnecessary static
ata: Convert to using %pOF instead of full_name
Don't populate the arrays cdb on the stack, instead make them static.
Makes the object code smaller by 230 bytes:
Before:
text data bss dec hex filename
3797 240 0 4037 fc5 drivers/ata/libata-zpodd.o
After:
text data bss dec hex filename
3407 400 0 3807 edf drivers/ata/libata-zpodd.o
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Intel AHCI controllers that also hide NVMe devices in their bar
can't use MSI interrupts, so disable them.
Reported-by: John Loy <john.robert.loy@gmail.com>
Tested-by: John Loy <john.robert.loy@gmail.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Fixes: d684a90d38 ("ahci: per-port msix support")
Cc: stable@vger.kernel.org # v4.5+
Signed-off-by: Tejun Heo <tj@kernel.org>
Pull RCU updates from Ingo Molnad:
"The main RCU related changes in this cycle were:
- Removal of spin_unlock_wait()
- SRCU updates
- RCU torture-test updates
- RCU Documentation updates
- Extend the sys_membarrier() ABI with the MEMBARRIER_CMD_PRIVATE_EXPEDITED variant
- Miscellaneous RCU fixes
- CPU-hotplug fixes"
* 'core-rcu-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (63 commits)
arch: Remove spin_unlock_wait() arch-specific definitions
locking: Remove spin_unlock_wait() generic definitions
drivers/ata: Replace spin_unlock_wait() with lock/unlock pair
ipc: Replace spin_unlock_wait() with lock/unlock pair
exit: Replace spin_unlock_wait() with lock/unlock pair
completion: Replace spin_unlock_wait() with lock/unlock pair
doc: Set down RCU's scheduling-clock-interrupt needs
doc: No longer allowed to use rcu_dereference on non-pointers
doc: Add RCU files to docbook-generation files
doc: Update memory-barriers.txt for read-to-write dependencies
doc: Update RCU documentation
membarrier: Provide expedited private command
rcu: Remove exports from rcu_idle_exit() and rcu_idle_enter()
rcu: Add warning to rcu_idle_enter() for irqs enabled
rcu: Make rcu_idle_enter() rely on callers disabling irqs
rcu: Add assertions verifying blocked-tasks list
rcu/tracing: Set disable_rcu_irq_enter on rcu_eqs_exit()
rcu: Add TPS() protection for _rcu_barrier_trace strings
rcu: Use idle versions of swait to make idle-hack clear
swait: Add idle variants which don't contribute to load average
...
This reverts commit 35f0b6a779.
We now conditionalize issuing of READ LOG PAGE on the TRUSTED
COMPUTING SUPPORTED bit in the identity data and this shouldn't be
necessary.
Signed-off-by: Tejun Heo <tj@kernel.org>
ATA-8 and later mirrors the TRUSTED COMPUTING SUPPORTED bit in word 48 of
the IDENTIFY DEVICE data. Check this before issuing a READ LOG PAGE
command to avoid issues with buggy devices. The only downside is that
we can't support Security Send / Receive for a device with an older
revision due to the conflicting use of this field in earlier
specifications.
tj: The reason we need this is because some devices which don't
support READ LOG PAGE lock up after getting issued that command.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Tested-by: David Ahern <dsahern@gmail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
This adds support the AHCI-compliant Serial ATA controller present
on MediaTek SoCs.
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Tejun Heo <tj@kernel.org>
The Octeon CF driver basically open-codes of_property_read_{bool|u32}()
using of_{find|get}_property() calls in its probe() method. Using the
modern DT APIs saves 2 LoCs and 16 bytes of object code (MIPS gcc 3.4.3).
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Ido reported that reading the log page on his systems fails,
so quirk it as it won't support ZBC or security protocols.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reported-by: Ido Schimmel <idosch@mellanox.com>
Tested-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
There is no agreed-upon definition of spin_unlock_wait()'s semantics,
and it appears that all callers could do just as well with a lock/unlock
pair. This commit therefore eliminates the spin_unlock_wait() call and
associated else-clause and hoists the then-clause's lock and unlock out of
the "if" statement. This should be safe from a performance perspective
because according to Tejun there should be few if any drivers that don't
set their own error handler.
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Acked-by: Tejun Heo <tj@kernel.org>
Cc: <linux-ide@vger.kernel.org>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Andrea Parri <parri.andrea@gmail.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
'rc' is known to be 0 at this point.
If 'platform_get_resource()' or 'devm_ioremap()' fail, return -ENOMEM
instead of 0 which means success.
tj: Changed error code from -ENOMEM to -ENODEV for get_resource
failure as suggested by Sergei.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Several legacy devices such as Geode-based Cisco ASA appliances
and DB800 development board do possess CS5536 IDE controller
with different PCI id than existing one. Using pata_generic is
not always feasible as at least DB800 requires MSR quirk from
pata_cs5536 to be used with vendor firmware.
Signed-off-by: Andrey Korolyov <andrey@xdel.ru>
CC: stable@vger.kernel.org
Signed-off-by: Tejun Heo <tj@kernel.org>
The IDE pins are managed by the pin controller, if we want to
use these, we need to ask the pin controller to explicitly enable
them as by default, these pins are used for other business and
most users just rely on the SATA bridge.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Tejun Heo <tj@kernel.org>
I added a proper pin control driver for the Gemini SoC, so retire
this custom code and rely on the pin controller to set up the pads.
The "IOMUX" which is routing signals between the ATA and SATA
bridge inside of the chip is not about pin control and remains in
place.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Tejun Heo <tj@kernel.org>
The newly introduced ahci_platform_shutdown() method is called during
system shutdown to disable host controller DMA and interrupts in order
to avoid potentially corrupting or otherwise interfering with a new
kernel being started with kexec.
Signed-off-by: Nate Watterson <nwatters@codeaurora.org>
Signed-off-by: Tejun Heo <tj@kernel.org>
Commit a53e35db70 ("reset: Ensure drivers are explicit when requesting
reset lines") started to transition the reset control request API calls
to explicitly state whether the driver needs exclusive or shared reset
control behavior. Convert all drivers requesting exclusive resets to the
explicit API call so the temporary transition helpers can be removed.
No functional changes.
Cc: linux-ide@vger.kernel.org
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Tejun Heo <tj@kernel.org>
Drop static on a local variable, when the variable is initialized before
any possible use. Thus, the static has no benefit.
The semantic patch that fixes this problem is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@bad exists@
position p;
identifier x;
type T;
@@
static T x@p;
...
x = <+...x...+>
@@
identifier x;
expression e;
type T;
position p != bad.p;
@@
-static
T x@p;
... when != x
when strict
?x = e;
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Tejun Heo <tj@kernel.org>
The kerneldoc comments for a couple of functions in drivers/ata/libata-eh.c
had fallen behind the current implementation, resulting in these doc build
warnings:
./drivers/ata/libata-eh.c:1449: warning: No description found for parameter 'link'
./drivers/ata/libata-eh.c:1449: warning: Excess function parameter 'ap' description in 'ata_eh_done'
./drivers/ata/libata-eh.c:1590: warning: No description found for parameter 'qc'
./drivers/ata/libata-eh.c:1590: warning: Excess function parameter 'dev' description in 'ata_eh_request_sense'
Update the comments and make the warnings go away.
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Tejun Heo <tj@kernel.org>
My static checker complains that "devno" can be negative, meaning that
we read before the start of the loop. I've looked at the code, and I
think the warning is right. This come from /proc so it's root only or
it would be quite a quite a serious bug. The call tree looks like this:
proc_scsi_write() <- gets id and channel from simple_strtoul()
-> scsi_add_single_device() <- calls shost->transportt->user_scan()
-> ata_scsi_user_scan()
-> ata_find_dev()
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: stable@vger.kernel.org # all versions at this point
Now that we have a custom printf format specifier, convert users of
full_name to use %pOF instead. This is preparation to remove storing
of the full path string for each node.
Signed-off-by: Rob Herring <robh@kernel.org>
Cc: Tejun Heo <tj@kernel.org>
Cc: linux-ide@vger.kernel.org
Signed-off-by: Tejun Heo <tj@kernel.org>
Add fallback compatibility string for R-Car Gen 2 and 3.
In the case of Renesas R-Car hardware we know that there are generations of
SoCs, e.g. Gen 1 and 2. But beyond that its not clear what the relationship
between IP blocks might be. For example, I believe that r8a7790 is older
than r8a7791 but that doesn't imply that the latter is a descendant of the
former or vice versa.
We can, however, by examining the documentation and behaviour of the
hardware at run-time observe that the current driver implementation appears
to be compatible with the IP blocks on SoCs within a given generation.
For the above reasons and convenience when enabling new SoCs a
per-generation fallback compatibility string scheme being adopted for
drivers for Renesas SoCs.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Acked-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Tejun Heo <tj@kernel.org>
The warning message "READ LOG DMA EXT failed, trying unqueued" in
ata_read_log_page() as well as the macro name ATA_HORKAGE_NO_NCQ_LOG
are confusing: the command READ LOG DMA EXT is not an queued NCQ command
unless it is encapsulated in a RECEIVE FPDMA QUEUED command.
From ACS-4 READ LOG DMA EXT description:
"The device processes the READ LOG DMA EXT command in the NCQ feature
set environment (see 4.13.6) if the READ LOG DMA EXT command is
encapsulated in a RECEIVE FPDMA QUEUED command (see 7.30) with the
inputs encapsulated as shown in 7.23.6."
To avoid confusion, fix the warning messsage to mention switching to PIO and
not "unqueued" and rename the macro ATA_HORKAGE_NO_NCQ_LOG to
ATA_HORKAGE_NO_DMA_LOG.
Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
We cannot build the new ftide010 code without also building the faraday
sata bridge driver:
drivers/ata/pata_ftide010.o: In function `pata_ftide010_probe':
pata_ftide010.c:(.text+0x2b8): undefined reference to `gemini_sata_bridge_get'
pata_ftide010.c:(.text+0x32c): undefined reference to `gemini_sata_get_muxmode'
pata_ftide010.c:(.text+0x358): undefined reference to `gemini_sata_bridge_enabled'
drivers/ata/pata_ftide010.o: In function `pata_ftide010_gemini_port_stop':
pata_ftide010.c:(.text+0x520): undefined reference to `gemini_sata_stop_bridge'
drivers/ata/pata_ftide010.o: In function `pata_ftide010_gemini_port_start':
pata_ftide010.c:(.text+0x5bc): undefined reference to `gemini_sata_start_bridge'
This adjusts the Kconfig dependencies accordingly.
Fixes: be4e456ed3 ("ata: Add driver for Faraday Technology FTIDE010")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Tejun Heo <tj@kernel.org>
Pull libata updates from Tejun Heo:
- Christoph added support for TCG OPAL self encrypting disks
- Minwoo added support for ATA PASS-THROUGH(32)
- Linus Walleij removed spurious drvdata assignments in some drivers
- Support for a few new device and other fixes
* 'for-4.13' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata: (33 commits)
sd: add support for TCG OPAL self encrypting disks
libata: fix build warning from unused goto label
libata: Support for an ATA PASS-THROUGH(32) command.
ahci: Add Device ID for ASMedia 1061R and 1062R
sata_via: Enable optional hotplug on VT6420
ata: ahci_brcm: Avoid writing to read-only registers
libata: Add the AHCI_HFLAG_NO_WRITE_TO_RO flag
libata: Add the AHCI_HFLAG_YES_ALPM flag
ata: ftide010: fix resource printing
libata: make the function name in comment match the actual function
ata: sata_rcar: make of_device_ids const.
ata: pata_octeon_cf: make of_device_ids const.
libata: Convert bare printks to pr_cont
libahci: wrong comments in ahci_do_softreset()
ata: declare ata_port_info structures as const
ata: Add driver for Faraday Technology FTIDE010
ata: Add DT bindings for the Gemini SATA bridge
ata: Add DT bindings for Faraday Technology FTIDE010
libata: implement SECURITY PROTOCOL IN/OUT
libata: factor out a ata_identify_page_supported helper
...
- Rework suspend-to-idle to allow it to take wakeup events signaled
by the EC into account on ACPI-based platforms in order to properly
support power button wakeup from suspend-to-idle on recent Dell
laptops (Rafael Wysocki).
That includes the core suspend-to-idle code rework, support for
the Low Power S0 _DSM interface, and support for the ACPI INT0002
Virtual GPIO device from Hans de Goede (required for USB keyboard
wakeup from suspend-to-idle to work on some machines).
- Stop trying to export the current CPU frequency via /proc/cpuinfo
on x86 as that is inaccurate and confusing (Len Brown).
- Rework the way in which the current CPU frequency is exported by
the kernel (over the cpufreq sysfs interface) on x86 systems with
the APERF and MPERF registers by always using values read from
these registers, when available, to compute the current frequency
regardless of which cpufreq driver is in use (Len Brown).
- Rework the PCI/ACPI device wakeup infrastructure to remove the
questionable and artificial distinction between "devices that
can wake up the system from sleep states" and "devices that can
generate wakeup signals in the working state" from it, which
allows the code to be simplified quite a bit (Rafael Wysocki).
- Fix the wakeup IRQ framework by making it use SRCU instead of
RCU which doesn't allow sleeping in the read-side critical
sections, but which in turn is expected to be allowed by the
IRQ bus locking infrastructure (Thomas Gleixner).
- Modify some computations in the intel_pstate driver to avoid
rounding errors resulting from them (Srinivas Pandruvada).
- Reduce the overhead of the intel_pstate driver in the HWP
(hardware-managed P-states) mode and when the "performance"
P-state selection algorithm is in use by making it avoid
registering scheduler callbacks in those cases (Len Brown).
- Rework the energy_performance_preference sysfs knob in
intel_pstate by changing the values that correspond to
different symbolic hint names used by it (Len Brown).
- Make it possible to use more than one cpuidle driver at the same
time on ARM (Daniel Lezcano).
- Make it possible to prevent the cpuidle menu governor from using
the 0 state by disabling it via sysfs (Nicholas Piggin).
- Add support for FFH (Fixed Functional Hardware) MWAIT in ACPI C1
on AMD systems (Yazen Ghannam).
- Make the CPPC cpufreq driver take the lowest nonlinear performance
information into account (Prashanth Prakash).
- Add support for hi3660 to the cpufreq-dt driver, fix the
imx6q driver and clean up the sfi, exynos5440 and intel_pstate
drivers (Colin Ian King, Krzysztof Kozlowski, Octavian Purdila,
Rafael Wysocki, Tao Wang).
- Fix a few minor issues in the generic power domains (genpd)
framework and clean it up somewhat (Krzysztof Kozlowski,
Mikko Perttunen, Viresh Kumar).
- Fix a couple of minor issues in the operating performance points
(OPP) framework and clean it up somewhat (Viresh Kumar).
- Fix a CONFIG dependency in the hibernation core and clean it up
slightly (Balbir Singh, Arvind Yadav, BaoJun Luo).
- Add rk3228 support to the rockchip-io adaptive voltage scaling
(AVS) driver (David Wu).
- Fix an incorrect bit shift operation in the RAPL power capping
driver (Adam Lessnau).
- Add support for the EPP field in the HWP (hardware managed
P-states) control register, HWP.EPP, to the x86_energy_perf_policy
tool and update msr-index.h with HWP.EPP values (Len Brown).
- Fix some minor issues in the turbostat tool (Len Brown).
- Add support for AMD family 0x17 CPUs to the cpupower tool and fix
a minor issue in it (Sherry Hurwitz).
- Assorted cleanups, mostly related to the constification of some
data structures (Arvind Yadav, Joe Perches, Kees Cook, Krzysztof
Kozlowski).
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iQIcBAABCAAGBQJZWrICAAoJEILEb/54YlRxZYMQAIRhfbyDxKq+ByvSilUS8kTA
AItwJ8FFzykhiwN75Cqabg4rAGyWma7IRs1vzU7zeC1aEQIn+bTQtvk+utZNI+g2
ANFlDha20q/sXsP/CDMMTIAdW9tSOC0TOvFI9s2V2Y8dJZhoekO4ctx34FAfUS5d
Ao6rwSAWCMsCXcGaTAlqTA+TEJmBG7u6Iq6hq6ngltoFwOv3mWWBVn52VVaJ7SMp
9/IPbbLGMFAedrgEBRGCR+MME1xZZpvcZIJaTt1Mgn7Cx3cJaysIUAvqY/SsvFGq
5FcUTcF2qpK3+AGawiAxZIjvOBsGRtIwqKinNIzYWs/NjiIdzmgVAmTeuPtTqp+5
HFehUdtkFcnuDnLqSNzAaZUa7tw84cJkwnbVMnesx0MkG6rZ1SeL22E2Sabpcdsh
3Yo1ThzJSxi59DhiiE92EQnNCEjmCldRy+8q5Ag035muxl6EJYvuNBMnZv/BMCUn
ltSNOrmps1DlN+Col8ORIeNzQ1YjYzWMqKAYzSbyccm4ug/iSHx0/DuESmQ4GTlF
YCwkmqyWiHrBwpl51jc+4a7SGlMmKRqU+MJes0CjagaaqoUAb8qeBOpzEJ0yNwjZ
wtI41l6blE6kbMD3yqGdCfiB2S7GlPVoxa15eX1wRyLH3fLjwwrzJirEaiBS86tI
1PzHZEOmBlh3DYC6DBKA
=Wsph
-----END PGP SIGNATURE-----
Merge tag 'pm-4.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management updates from Rafael Wysocki:
"The big ticket items here are the rework of suspend-to-idle in order
to add proper support for power button wakeup from it on recent Dell
laptops and the rework of interfaces exporting the current CPU
frequency on x86.
In addition to that, support for a few new pieces of hardware is
added, the PCI/ACPI device wakeup infrastructure is simplified
significantly and the wakeup IRQ framework is fixed to unbreak the IRQ
bus locking infrastructure.
Also, there are some functional improvements for intel_pstate, tools
updates and small fixes and cleanups all over.
Specifics:
- Rework suspend-to-idle to allow it to take wakeup events signaled
by the EC into account on ACPI-based platforms in order to properly
support power button wakeup from suspend-to-idle on recent Dell
laptops (Rafael Wysocki).
That includes the core suspend-to-idle code rework, support for the
Low Power S0 _DSM interface, and support for the ACPI INT0002
Virtual GPIO device from Hans de Goede (required for USB keyboard
wakeup from suspend-to-idle to work on some machines).
- Stop trying to export the current CPU frequency via /proc/cpuinfo
on x86 as that is inaccurate and confusing (Len Brown).
- Rework the way in which the current CPU frequency is exported by
the kernel (over the cpufreq sysfs interface) on x86 systems with
the APERF and MPERF registers by always using values read from
these registers, when available, to compute the current frequency
regardless of which cpufreq driver is in use (Len Brown).
- Rework the PCI/ACPI device wakeup infrastructure to remove the
questionable and artificial distinction between "devices that can
wake up the system from sleep states" and "devices that can
generate wakeup signals in the working state" from it, which allows
the code to be simplified quite a bit (Rafael Wysocki).
- Fix the wakeup IRQ framework by making it use SRCU instead of RCU
which doesn't allow sleeping in the read-side critical sections,
but which in turn is expected to be allowed by the IRQ bus locking
infrastructure (Thomas Gleixner).
- Modify some computations in the intel_pstate driver to avoid
rounding errors resulting from them (Srinivas Pandruvada).
- Reduce the overhead of the intel_pstate driver in the HWP
(hardware-managed P-states) mode and when the "performance" P-state
selection algorithm is in use by making it avoid registering
scheduler callbacks in those cases (Len Brown).
- Rework the energy_performance_preference sysfs knob in intel_pstate
by changing the values that correspond to different symbolic hint
names used by it (Len Brown).
- Make it possible to use more than one cpuidle driver at the same
time on ARM (Daniel Lezcano).
- Make it possible to prevent the cpuidle menu governor from using
the 0 state by disabling it via sysfs (Nicholas Piggin).
- Add support for FFH (Fixed Functional Hardware) MWAIT in ACPI C1 on
AMD systems (Yazen Ghannam).
- Make the CPPC cpufreq driver take the lowest nonlinear performance
information into account (Prashanth Prakash).
- Add support for hi3660 to the cpufreq-dt driver, fix the imx6q
driver and clean up the sfi, exynos5440 and intel_pstate drivers
(Colin Ian King, Krzysztof Kozlowski, Octavian Purdila, Rafael
Wysocki, Tao Wang).
- Fix a few minor issues in the generic power domains (genpd)
framework and clean it up somewhat (Krzysztof Kozlowski, Mikko
Perttunen, Viresh Kumar).
- Fix a couple of minor issues in the operating performance points
(OPP) framework and clean it up somewhat (Viresh Kumar).
- Fix a CONFIG dependency in the hibernation core and clean it up
slightly (Balbir Singh, Arvind Yadav, BaoJun Luo).
- Add rk3228 support to the rockchip-io adaptive voltage scaling
(AVS) driver (David Wu).
- Fix an incorrect bit shift operation in the RAPL power capping
driver (Adam Lessnau).
- Add support for the EPP field in the HWP (hardware managed
P-states) control register, HWP.EPP, to the x86_energy_perf_policy
tool and update msr-index.h with HWP.EPP values (Len Brown).
- Fix some minor issues in the turbostat tool (Len Brown).
- Add support for AMD family 0x17 CPUs to the cpupower tool and fix a
minor issue in it (Sherry Hurwitz).
- Assorted cleanups, mostly related to the constification of some
data structures (Arvind Yadav, Joe Perches, Kees Cook, Krzysztof
Kozlowski)"
* tag 'pm-4.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (69 commits)
cpufreq: Update scaling_cur_freq documentation
cpufreq: intel_pstate: Clean up after performance governor changes
PM: hibernate: constify attribute_group structures.
cpuidle: menu: allow state 0 to be disabled
intel_idle: Use more common logging style
PM / Domains: Fix missing default_power_down_ok comment
PM / Domains: Fix unsafe iteration over modified list of domains
PM / Domains: Fix unsafe iteration over modified list of domain providers
PM / Domains: Fix unsafe iteration over modified list of device links
PM / Domains: Handle safely genpd_syscore_switch() call on non-genpd device
PM / Domains: Call driver's noirq callbacks
PM / core: Drop run_wake flag from struct dev_pm_info
PCI / PM: Simplify device wakeup settings code
PCI / PM: Drop pme_interrupt flag from struct pci_dev
ACPI / PM: Consolidate device wakeup settings code
ACPI / PM: Drop run_wake from struct acpi_device_wakeup_flags
PM / QoS: constify *_attribute_group.
PM / AVS: rockchip-io: add io selectors and supplies for rk3228
powercap/RAPL: prevent overridding bits outside of the mask
PM / sysfs: Constify attribute groups
...
around. Highlights include:
- Conversion of a bunch of security documentation into RST
- The conversion of the remaining DocBook templates by The Amazing
Mauro Machine. We can now drop the entire DocBook build chain.
- The usual collection of fixes and minor updates.
-----BEGIN PGP SIGNATURE-----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=cVjZ
-----END PGP SIGNATURE-----
Merge tag 'docs-4.13' of git://git.lwn.net/linux
Pull documentation updates from Jonathan Corbet:
"There has been a fair amount of activity in the docs tree this time
around. Highlights include:
- Conversion of a bunch of security documentation into RST
- The conversion of the remaining DocBook templates by The Amazing
Mauro Machine. We can now drop the entire DocBook build chain.
- The usual collection of fixes and minor updates"
* tag 'docs-4.13' of git://git.lwn.net/linux: (90 commits)
scripts/kernel-doc: handle DECLARE_HASHTABLE
Documentation: atomic_ops.txt is core-api/atomic_ops.rst
Docs: clean up some DocBook loose ends
Make the main documentation title less Geocities
Docs: Use kernel-figure in vidioc-g-selection.rst
Docs: fix table problems in ras.rst
Docs: Fix breakage with Sphinx 1.5 and upper
Docs: Include the Latex "ifthen" package
doc/kokr/howto: Only send regression fixes after -rc1
docs-rst: fix broken links to dynamic-debug-howto in kernel-parameters
doc: Document suitability of IBM Verse for kernel development
Doc: fix a markup error in coding-style.rst
docs: driver-api: i2c: remove some outdated information
Documentation: DMA API: fix a typo in a function name
Docs: Insert missing space to separate link from text
doc/ko_KR/memory-barriers: Update control-dependencies example
Documentation, kbuild: fix typo "minimun" -> "minimum"
docs: Fix some formatting issues in request-key.rst
doc: ReSTify keys-trusted-encrypted.txt
doc: ReSTify keys-request-key.txt
...
Just wire up the generic TCG OPAL infrastructure to the SCSI disk driver
and the Security In/Out commands.
Note that I don't know of any actual SCSI disks that do support TCG OPAL,
but this is required to support ATA disks through libata.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
b1ffbf854e ("libata: Support for an ATA PASS-THROUGH(32) command.")
introduced an unused goto label. Remove it.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Tejun Heo <tj@kernel.org>
Currently, there are two separate ways of handling device wakeup
settings in the ACPI core, depending on whether this is runtime
wakeup or system wakeup (from sleep states). However, after the
previous commit eliminating the run_wake ACPI device wakeup flag,
there is no difference between the two any more at the ACPI level,
so they can be combined.
For this reason, introduce acpi_pm_set_device_wakeup() to replace both
acpi_pm_device_run_wake() and acpi_pm_device_sleep_wake() and make it
check the ACPI device object's wakeup.valid flag to determine whether
or not the device can be set up to generate wakeup signals.
Also notice that zpodd_enable/disable_run_wake() only call
device_set_run_wake() because acpi_pm_device_run_wake() called
device_run_wake(), which is not done by acpi_pm_set_device_wakeup(),
so drop the now redundant device_set_run_wake() calls from there.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
SAT-4(SCSI/ATA Translation) supports for an ata pass-thru(32).
This patch will allow to translate an ata pass-thru(32) SCSI cmd
to an ATA cmd.
Signed-off-by: Minwoo Im <dn3108@gmail.com>
Reviewed-by: Bart Van Assche <bart.vanassche@wdc.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
VT6420 seems to have the same hotplug capability as VT6421.
However, enabling hotplug needs to expose SCR registers which can cause
problems. It works for me but might break elsewhere. So add a module
parameter vt6420_hotplug to enable this feature.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Tejun Heo <tj@kernel.org>
This commit makes use of the AHCI_HFLAG_YES_ALPM flag to prevent
the driver from writing to the read-only Host Capability register.
It also sets the AHCI_HFLAG_NO_WRITE_TO_RO flag to prevent the AHCI
library from writing to read-only registers.
Signed-off-by: Doug Berger <opendmb@gmail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
While most hardware will simply ignore a write to a read-only register,
some hardware will signal an abort if this occurs.
This commit introduces the flag AHCI_HFLAG_NO_WRITE_TO_RO to prevent the
AHCI library from attempting to write to the HOST_CAP, HOST_CAP2, and
HOST_PORTS_IMPL registers which may be read-only.
Signed-off-by: Doug Berger <opendmb@gmail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Some hardware is capable of supporting Aggresive Link Power Management
even though it is not indicated by the Host Capability register.
This commit adds the AHCI_HFLAG_YES_ALPM flag to the AHCI library to
allow indication of this quirk when the Host Capability register is
Read Only and therefore cannot be changed.
Signed-off-by: Doug Berger <opendmb@gmail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
The new driver uses an incorrect format string for resource_size_t:
drivers/ata/pata_ftide010.c: In function 'pata_ftide010_probe':
drivers/ata/pata_ftide010.c:520:17: warning: format '%x' expects argument of type 'unsigned int', but argument 5 has type 'resource_size_t {aka long long unsigned int}' [-Wformat=]
The nicest way to print the address is to pretty-print the resource
using %pR.
Fixes: be4e456ed3 ("ata: Add driver for Faraday Technology FTIDE010")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Tejun Heo <tj@kernel.org>
The function name used to be ata_scsiop_mode_select() but renamed to
ata_scsi_mode_select_xlat(). Update the comment accordingly.
tj: Minor commit desc update.
Signed-off-by: Minwoo Im <dn3108@gmail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
of_device_ids are not supposed to change at runtime. All functions
working with of_device_ids provided by <linux/of.h> work with const
of_device_ids. So mark the non-const structs as const.
File size before:
text data bss dec hex filename
3946 2296 0 6242 1862 drivers/ata/sata_rcar.o
File size after constify sata_rcar_match.
text data bss dec hex filename
5554 696 0 6250 186a drivers/ata/sata_rcar.o
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
of_device_ids are not supposed to change at runtime. All functions
working with of_device_ids provided by <linux/of.h> work with const
of_device_ids. So mark the non-const structs as const.
File size before:
text data bss dec hex filename
465 696 4 1165 48d drivers/ata/pata_octeon_cf.o
File size after constify octeon_cf_match.
text data bss dec hex filename
865 280 4 1149 47d drivers/ata/pata_octeon_cf.o
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Linus Torvalds changed the behavior of printks without KERN_<LEVEL>.
Convert the continuation prints to use pr_cont.
At the same time, convert the existing printks with KERN_<LEVEL> to
pr_<level>
Miscellanea:
o Coalesce a multiline format
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
AHCI 1.3.1 Spec says that software shall build two H2D register
FISes in the command list to send a software reset.
The comments in ahci_do_softreset() is currently D2H instead of H2D.
Signed-off-by: Minwoo Im <dn3108@gmail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
ata_port_info structures are either copied to other objects or their
references are stored in objects of type const. So, ata_port_info
structures having similar usage pattern can be made const.
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
This adds a driver for the Faraday Technology FTIDE010
PATA IP block.
When used with the Storlink/Storm/Cortina Systems Gemini
SoC, the PATA interface is accompanied by a PATA<->SATA
bridge, so while the device appear as a PATA controller,
it attaches physically to SATA disks, and also has a
designated memory area with registers to set up the bridge.
The Gemini SATA bridge is separated into its own driver
file to make things modular and make it possible to reuse
the PATA driver as stand-alone on other systems than the
Gemini.
dmesg excerpt from the D-Link DIR-685 storage router:
gemini-sata-bridge 46000000.sata: SATA ID 00000e00, PHY ID: 01000100
gemini-sata-bridge 46000000.sata: set up the Gemini IDE/SATA nexus
ftide010 63000000.ata: set up Gemini PATA0
ftide010 63000000.ata: device ID 00000500, irq 26, io base 0x63000000
ftide010 63000000.ata: SATA0 (master) start
gemini-sata-bridge 46000000.sata: SATA0 PHY ready
scsi host0: pata-ftide010
ata1: PATA max UDMA/133 irq 26
ata1.00: ATA-8: INTEL SSDSA2CW120G3, 4PC10302, max UDMA/133
ata1.00: 234441648 sectors, multi 1: LBA48 NCQ (depth 0/32)
ata1.00: configured for UDMA/133
scsi 0:0:0:0: Direct-Access ATA INTEL SSDSA2CW12 0302 PQ: 0 ANSI: 5
ata1.00: Enabling discard_zeroes_data
sd 0:0:0:0: [sda] 234441648 512-byte logical blocks: (120 GB/112 GiB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Write cache: enabled, read cache:
enabled, doesn't support DPO or FUA
ata1.00: Enabling discard_zeroes_data
ata1.00: Enabling discard_zeroes_data
sd 0:0:0:0: [sda] Attached SCSI disk
After this I can flawlessly mount and read/write copy etc files
from /dev/sda[n].
Cc: John Feng-Hsin Chiang <john453@faraday-tech.com>
Cc: Greentime Hu <green.hu@gmail.com>
Acked-by: Hans Ulli Kroll <ulli.kroll@googlemail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
tj: Updated line continuation style for consistency as pointed out by
Sergei.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Cc: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
It is core functionality, and only one of the users is in the EH code.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Tejun Heo <tj@kernel.org>
Ls1088a is new introduced arm-based soc with sata support with
following features:
* Complies with the serial ATA 3.0 specification
and the AHCI 1.3.1 specification
* Contains a high-speed descriptor-based DMA controller
* Supports the following:
* Speeds of 1.5 Gb/s (first-generation SATA),
3 Gb/s (second-generation SATA), and 6 Gb/s (third-generation SATA)
* FIS-based switching
* Native command queuing (NCQ) commands
* Port multiplier operation
* Asynchronous notification
* SATA Vendor BIST mode
Signed-off-by: Tang Yuantian <andy.tang@nxp.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
ata_parse_force_one() was incorrectly comparing @p to @endp when it
should have been comparing @id. The only consequence is that it may
end up using an invalid port number in "libata.force" module param
instead of rejecting it.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Petru-Florin Mihancea <petrum@gmail.com>
Link: https://bugzilla.kernel.org/show_bug.cgi?id=195785
ata_host_alloc_pinfo() assigns the host pointer to the
struct device * drvdata, do not assign it a second time.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Tejun Heo <tj@kernel.org>
ata_host_alloc_pinfo() assigns the host pointer to the
struct device * drvdata, do not assign it a second time.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Tejun Heo <tj@kernel.org>
ata_host_alloc_pinfo() assigns the host pointer to the
struct device * drvdata, do not assign it a second time.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Tejun Heo <tj@kernel.org>
ata_host_alloc_pinfo() assigns the host pointer to the
struct device * drvdata, do not assign it a second time.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Tejun Heo <tj@kernel.org>
ata_host_alloc_pinfo() assigns the host pointer to the
struct device * drvdata, do not assign drv_data like this.
Since ata_host_alloc_pinfo() is called after this site, the
correct value is set eventually, but this assignment is just
plain pointless.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Tejun Heo <tj@kernel.org>
ata_host_alloc_pinfo() assigns the host pointer to the
struct device * drvdata, do not assign it a second time.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Tejun Heo <tj@kernel.org>
This reverts commit 368e5fbdfc.
devm_ioremap_resource() enforces that there are no overlapping
resources, where as devm_ioremap() does not. The sata phy driver needs
a subset of the sata IO address space, so maps some of the sata
address space. As a result, sata_mv now fails to probe, reporting it
cannot get its resources, and so we don't have any SATA disks.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Cc: stable@vger.kernel.org # v4.11+
Signed-off-by: Tejun Heo <tj@kernel.org>
The libata documentation is now using ReST. Update references
to it to point to the new place.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Acked-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
When platform_get_irq() fails, it returns an error code, which
libahci_platform and replaces it by -EINVAL. This commit fixes that by
propagating the error code. It fixes the situation where
platform_get_irq() returns -EPROBE_DEFER because the interrupt
controller is not available yet, and generally looks like the right
thing to do.
We pay attention to not show the "no irq" message when we are in an
EPROBE_DEFER situation, because the driver probing will be retried
later on, once the interrupt controller becomes available to provide
the interrupt.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Here, Clock enable can failed. So adding an error check for
clk_prepare_enable.
tj: minor style updates
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
(Correction in this resend: fixed function name acer_sa5_271_workaround; fixed
the always-true condition in the function; fixed description.)
On the Acer Switch Alpha 12 (model number: SA5-271), the internal SSD may not
get detected because the port_map and CAP.nr_ports combination causes the driver
to skip the port that is actually connected to the SSD. More specifically,
either all SATA ports are identified as DUMMY, or all ports get ``link down''
and never get up again.
This problem occurs occasionally. When this problem occurs, CAP may hold a
value of 0xC734FF00 or 0xC734FF01 and port_map may hold a value of 0x00 or 0x01.
When this problem does not occur, CAP holds a value of 0xC734FF02 and port_map
may hold a value of 0x07. Overriding the CAP value to 0xC734FF02 and port_map to
0x7 significantly reduces the occurrence of this problem.
Link: https://bugzilla.kernel.org/attachment.cgi?id=253091
Signed-off-by: Sui Chen <suichen6@gmail.com>
Tested-by: Damian Ivanov <damianatorrpm@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Tejun Heo <tj@kernel.org>
The XPFO [1] patchset may unmap pages from physmap if they happened to be
destined for userspace. If such a page is unmapped, it needs to be
remapped. Rather than test if a page is in the highmem/xpfo unmapped state,
Christoph suggested [2] that we simply always map the page.
v2: * drop comment about bounce buffer
* don't save IRQs before kmap/unmap
* formatting
[1]: https://lkml.org/lkml/2016/11/4/245
[2]: https://lkml.org/lkml/2016/11/4/253
Suggested-and-reviewed-by: Christoph Hellwig <hch@infradead.org>
Signed-off-by: Tycho Andersen <tycho@docker.com>
CC: Juerg Haefliger <juerg.haefliger@hpe.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
The libata documentation is now using ReST. Update references
to it to point to the new place.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Driver updates for ARM SoCs.
* Reset subsystem, merged through arm-soc by tradition:
- Make bool drivers explicitly non-modular
- New support for i.MX7 and Arria10 reset controllers
* PATA driver for Palmchip BK371 (acked by Tejun)
* Power domain drivers for i.MX (GPC, GPCv2)
- Moved out of mach-imx for GPC
- Bunch of tweaks, fixes, etc
* PMC support for Tegra186
* SoC detection support for Renesas RZ/G1H and RZ/G1N
* Move Tegra flow controller driver from mach directory to drivers/soc
- (Power management / CPU power driver)
* Misc smaller tweaks for other platforms
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJZEAZuAAoJEIwa5zzehBx3jCEP/1dcXY746rQoOMUDPyWF5+SZ
w0l8dHUQhu4WjNGryfb9DbyiE3d6xlvPVzr9AJeAg6c5I+iikgeogS0XHNpWCU96
FR1Ftb6zo8DIaGognBL9bK5HM7NXjd/EKBkMk0Ggs9/NRFUnakkbpdfivsl2BACx
mCGo15+kbgQSQsMJtd5/KfsgY5h7lXJG0fZ8LV5E1E5BSa/AofZtKVgCKfhbd0zV
gQqm7xfxtURHtucc7MYNEoKNk5rlrZhOlG6DdG0d6+rscCBrmL1I5giqm8y24+wW
z+JJuk21+oVtltLz09JuX51xur3CGyJ+qNJdRPE1P1Udn7wj5zA+ew9qqJi1cgNf
63tBxooBpH6R8dGcOfjKECD6lBBqBr/Dd8ReWbMyn0XF1HMAxgpfPtExu9WcDzGu
9Fr/shUiEA3jqhbzSy6DCHugpnHPdHPyY64MqzisgOEVsituQ7MSefTIGSNusDlk
K36I7j93mDAF5y2fTXqbjZKoRuu6KCySvGDXzBqGwhcNzUQk14iPwjtMDZ/l9Raj
sQJCUxHntUovHs+VTCwS7ahqZyn0VRNx2bt1aJXNHKzuUovpA9/X5X9HCRZJDovB
0bCGQZ124+H/VsWvSjVtIh7oknU3vSQJPxS6KLKoi3rvywuqW562lGjCTqvjBJKD
FMZ5NA8VoWXM2rgTDOyx
=B43K
-----END PGP SIGNATURE-----
Merge tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC driver updates from Olof Johansson:
"Driver updates for ARM SoCs:
Reset subsystem, merged through arm-soc by tradition:
- Make bool drivers explicitly non-modular
- New support for i.MX7 and Arria10 reset controllers
PATA driver for Palmchip BK371 (acked by Tejun)
Power domain drivers for i.MX (GPC, GPCv2)
- Moved out of mach-imx for GPC
- Bunch of tweaks, fixes, etc
PMC support for Tegra186
SoC detection support for Renesas RZ/G1H and RZ/G1N
Move Tegra flow controller driver from mach directory to drivers/soc
- (Power management / CPU power driver)
Misc smaller tweaks for other platforms"
* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (60 commits)
soc: pm-domain: Fix the mangled urls
soc: renesas: rcar-sysc: Add support for R-Car H3 ES2.0
soc: renesas: rcar-sysc: Add support for fixing up power area tables
soc: renesas: Register SoC device early
soc: imx: gpc: add workaround for i.MX6QP to the GPC PD driver
dt-bindings: imx-gpc: add i.MX6 QuadPlus compatible
soc: imx: gpc: add defines for domain index
soc: imx: Add GPCv2 power gating driver
dt-bindings: Add GPCv2 power gating driver
ARM/clk: move the ICST library to drivers/clk
ARM: plat-versatile: remove stale clock header
ARM: keystone: Drop PM domain support for k2g
soc: ti: Add ti_sci_pm_domains driver
dt-bindings: Add TI SCI PM Domains
PM / Domains: Do not check if simple providers have phandle cells
PM / Domains: Add generic data pointer to genpd data struct
soc/tegra: Add initial flowctrl support for Tegra132/210
soc/tegra: flowctrl: Add basic platform driver
soc/tegra: Move Tegra flowctrl driver
ARM: tegra: Remove unnecessary inclusion of flowctrl header
...
Pull libata updates from Tejun Heo:
"The biggest core change is removal of SCT WRITE SAME support, which
never worked properly.
Other than that, trivial updates in core code and specific embedded
driver updates"
* 'for-4.12' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata:
libata: remove SCT WRITE SAME support
libata: reject passthrough WRITE SAME requests
dt-bindings: ata: add DT bindings for ahci-dm816 SATA controller
ata: ahci: add support for DaVinci DM816 SATA controller
pata: remove the at91 driver
libata: make ata_sg_clean static over again
libata: use setup_deferrable_timer
ata: allow subsystem to be used on m32r and s390 archs
Delete redundant return value check of platform_get_resource()
ata: constify of_device_id structures
This was already disabled a while ago because it caused I/O errors,
and it's severly getting into the way of the discard / write zeroes
rework.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
The WRITE SAME to TRIM translation rewrites the DATA OUT buffer. While
the SCSI code accomodates for this by passing a read-writable buffer
userspace applications don't cater for this behavior. In fact it can
be used to rewrite e.g. a readonly file through mmap and should be
considered as a security fix.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Cc: stable@vger.kernel.org
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Clear IORDYINT, INTRSTAT and DMAERROR bits of BMISP register
(value '1' needs to be written to the bit to clear it).
Suggested-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Acked-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
This reverts commit 5946fdaee4.
The original commit's assumption that the secondary port is
unconnected turns out to be false.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Markku Pesonen <tourula@gmail.com>
Fixes: 5946fdaee4 ("pata_atiixp: Don't use unconnected secondary port on SB600/SB700")
Cc: Darren Stevens <darren@stevens-zone.net>
This SATA controller is quite similar to the one present on the DA850
SoC, but the PHY configuration is different and it supports two HBA
ports.
The IP suffers from the same PMP issue the DA850 does - if we enable
PMP but don't use it - softreset fails. Appropriate workaround was
implemented in this driver as well.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
This driver is orphan since commit b2026f708e ("ARM: at91: remove
at91sam9260/at91sam9g20 legacy board support"). Given that nobody cared
adding DT support to it, it probably means it's no longer used and is
thus a good candidate for removal.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Fixes the following sparse warning:
drivers/ata/libata-core.c:4913:6: warning: symbol 'ata_sg_clean' was not
declared. Should it be static?
Signed-off-by: Jason Yan <yanaijie@huawei.com>
Use setup_deferrable_timer() instead of init_timer_deferrable() to
simplify the code.
Signed-off-by: Geliang Tang <geliangtang@gmail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Sata ecc is controlled by only 1 bit which is 24bit in big-endian
in ecc register. So only setting 24bit to disable sata ecc prevents
other bits from being overwritten in ecc register.
Signed-off-by: Tang Yuantian <andy.tang@nxp.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Both archs should work just fine with libata subsystem nowadays.
Suggested-by: Christoph Hellwig <hch@infradead.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Delete error handling from the result of a call to platform_get_resource()
when the value is immediately passed to devm_ioremap_resource().
Signed-off-by: Belen Sarabia <belensarabia@gmail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
ata_sff_qc_issue() expects upper layers to never issue commands on a
command protocol that it doesn't implement. While the assumption
holds fine with the usual IO path, nothing filters based on the
command protocol in the passthrough path (which was added later),
allowing the warning to be tripped with a passthrough command with the
right (well, wrong) protocol.
Failing with AC_ERR_SYSTEM is the right thing to do anyway. Remove
the unnecessary WARN.
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Link: http://lkml.kernel.org/r/CACT4Y+bXkvevNZU8uP6X0QVqsj6wNoUA_1exfTSOzc+SmUtMOA@mail.gmail.com
Signed-off-by: Tejun Heo <tj@kernel.org>
Without this patch, failed probe would not free resources like irq.
ata port tdev object currently hold a reference to the ata port
object. Therefore the ata port object release function will not get
called until the ata_tport_release is called. But that would never
happen, releasing the last reference of ata port dev is done by
scsi_host_release, which is called by ata_host_release when the ata
port object is released.
The ata device objects actually do not need to explicitly hold a
reference to their real counterpart, given the transport objects are
the children of these objects and device_add() is call for each child.
We know the parent will not be deleted until we call the child's
device_del().
Reported-by: Matthew Whitehead <tedheadster@gmail.com>
Tested-by: Matthew Whitehead <tedheadster@gmail.com>
Suggested-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Gwendal Grignou <gwendal@chromium.org>
Signed-off-by: Tejun Heo <tj@kernel.org>
Declare of_device_id structures as const as they are either passed to
the macro MODULE_DEVICE_TABLE or stored in the of_match_table field of a
device_driver structure. This field is of type const, so of_device_id
structures having this property can be made const too.
Cross compiled the files drivers/ata/pata_macio.c and
drivers/ata/pata_mpc52xx.c for powerpc architecture.
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
This is the set of stuff that didn't quite make the initial pull and a
set of fixes for stuff which did. The new stuff is basically lpfc
(nvme), qedi and aacraid. The fixes cover a lot of previously
submitted stuff, the most important of which probably covers some of
the failing irq vectors allocation and other fallout from having the
SCSI command allocated as part of the block allocation functions.
Signed-off-by: James E.J. Bottomley <jejb@linux.vnet.ibm.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=e+6v
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull more SCSI updates from James Bottomley:
"This is the set of stuff that didn't quite make the initial pull and a
set of fixes for stuff which did.
The new stuff is basically lpfc (nvme), qedi and aacraid. The fixes
cover a lot of previously submitted stuff, the most important of which
probably covers some of the failing irq vectors allocation and other
fallout from having the SCSI command allocated as part of the block
allocation functions"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (59 commits)
scsi: qedi: Fix memory leak in tmf response processing.
scsi: aacraid: remove redundant zero check on ret
scsi: lpfc: use proper format string for dma_addr_t
scsi: lpfc: use div_u64 for 64-bit division
scsi: mac_scsi: Fix MAC_SCSI=m option when SCSI=m
scsi: cciss: correct check map error.
scsi: qla2xxx: fix spelling mistake: "seperator" -> "separator"
scsi: aacraid: Fixed expander hotplug for SMART family
scsi: mpt3sas: switch to pci_alloc_irq_vectors
scsi: qedf: fixup compilation warning about atomic_t usage
scsi: remove scsi_execute_req_flags
scsi: merge __scsi_execute into scsi_execute
scsi: simplify scsi_execute_req_flags
scsi: make the sense header argument to scsi_test_unit_ready mandatory
scsi: sd: improve TUR handling in sd_check_events
scsi: always zero sshdr in scsi_normalize_sense
scsi: scsi_dh_emc: return success in clariion_std_inquiry()
scsi: fix memory leak of sdpk on when gd fails to allocate
scsi: sd: make sd_devt_release() static
scsi: qedf: Add QLogic FastLinQ offload FCoE driver framework.
...
Fix typos and add the following to the scripts/spelling.txt:
followings||following
While we are here, add a missing colon in the boilerplate in DT binding
documents. The "you SoC" in allwinner,sunxi-pinctrl.txt was fixed as
well.
I reworded "as the followings:" to "as follows:" for
drivers/usb/gadget/udc/renesas_usb3.c.
Link: http://lkml.kernel.org/r/1481573103-11329-32-git-send-email-yamada.masahiro@socionext.com
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Driver updates for ARM SoCs.
A handful of driver changes this time around. The larger changes are:
- Reset drivers for hi3660 and zx2967
- AHCI driver for Davinci, acked by Tejun and brought in here due to
platform dependencies
- Cleanups of atmel-ebi (External Bus Interface)
- Tweaks for Rockchip GRF (General Register File) usage (kitchensink misc
register range on the SoCs)
- PM domains changes for support of two new ZTE SoCs (zx296718 and zx2967)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJYrM7/AAoJEIwa5zzehBx3qisP/18NwvbYvC3rMza7k+TEU66n
vuEF9KW5GhUpQPbNIsTer5qHhC7ZgL7RoR/H7mpZcCxfhYiNXuUaOv8TMGK+WTLQ
HH6QTs4mARLh1IrRcog1hoElzzqMVxaQgODeaaG1DcPvTqHWsQurbXsf17tCQOri
nWKyxFpLNlu0kktkGb5JWrM4XBjU9KsW7LME9H86wG8HmB6+mcT5ddeYwW5nD8cG
txXgmMjdTEKcpbeTg3cAzL4504auhIl4R9uK+8dc1sw+e9T0nXNDS9IkmLPwWtSR
u8q6zQ3zReoDw4jGUgPP0ILHudfQsiMdWS+P2hw/krpbtLlQ+irHDVa1VA3NLiUT
9aG9cNTYRMo3ct22YEeWsnAC04XOxpCsqHTR+UWuZaBmf3eoMIXnsafTuwLzqKlQ
Ent/4eFPInMAzDH8Kaf1Hh0918qkgF2bNlshem11TccQKvHP+qCoHk6mKGxwEj5k
E1UEG4S6k6zNqjLwmTBBbk8sLMl/WVo6RMSMz+JflatgPmVZco4EX2O73iKGAJVU
5GfHIUG9Yl4+aTIUORu59cWxOCApK0kqERrFKe412BMurXlLfqVcr/H2tiiuWnn1
cEJ9d+uBd8IxTIQX0iEYGUAkX97mhxGUYdqGQuGJSV+MOfWX1zNP1sI4EscLGKQj
sDDZScCaguM4xE20Jum1
=od7u
-----END PGP SIGNATURE-----
Merge tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC driver updates from Arnd Bergmann:
"Driver updates for ARM SoCs.
A handful of driver changes this time around. The larger changes are:
- Reset drivers for hi3660 and zx2967
- AHCI driver for Davinci, acked by Tejun and brought in here due to
platform dependencies
- Cleanups of atmel-ebi (External Bus Interface)
- Tweaks for Rockchip GRF (General Register File) usage (kitchensink
misc register range on the SoCs)
- PM domains changes for support of two new ZTE SoCs (zx296718 and
zx2967)"
* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (53 commits)
soc: samsung: pmu: Add register defines for pad retention control
reset: make zx2967 explicitly non-modular
reset: core: fix reset_control_put
soc: samsung: pm_domains: Read domain name from the new label property
soc: samsung: pm_domains: Remove message about failed memory allocation
soc: samsung: pm_domains: Remove unused name field
soc: samsung: pm_domains: Use full names in subdomains registration log
sata: ahci-da850: un-hardcode the MPY bits
sata: ahci-da850: add a workaround for controller instability
sata: ahci: export ahci_do_hardreset() locally
sata: ahci-da850: implement a workaround for the softreset quirk
sata: ahci-da850: add device tree match table
sata: ahci-da850: get the sata clock using a connection id
soc: samsung: pmu: Remove duplicated define for ARM_L2_OPTION register
memory: atmel-ebi: Enable the SMC clock if specified
soc: samsung: pmu: Remove unused and duplicated defines
memory: atmel-ebi: Properly handle multiple reference to the same CS
memory: atmel-ebi: Fix the test to enable generic SMC logic
soc: samsung: pm_domains: Add new Exynos5433 compatible
soc: samsung: pmu: Add dummy support for Exynos5433 SoC
...
All but one caller want the decoded sense header, so offer the existing
__scsi_execute helper as the public scsi_execute API to simply the
callers.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Pull libata updates from Tejun Heo:
- Bartlomiej added pata_falcon
- Christoph is trying to remove use of static 4k buf. It's still WIP
- config cleanup around HAS_DMA
- other fixes and driver-specific changes
* 'for-4.11' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata: (29 commits)
ata: pata_of_platform: using of_property_read_u32() helper
pata_atiixp: Don't use unconnected secondary port on SB600/SB700
libata-sff: Don't scan disabled ports when checking for legacy mode.
pata_octeon_cf: remove unused local variables from octeon_cf_set_piomode()
ahci: qoriq: added ls2088a platforms support
ahci: qoriq: report error when ecc register address is missing in dts
ahci: qoriq: added a condition to enable dma coherence
Revert "libata: switch to dynamic allocation instead of ata_scsi_rbuf"
ahci: imx: fix building without hwmon or thermal
ata: add Atari Falcon PATA controller driver
ata: pass queued command to ->sff_data_xfer method
ata: allow subsystem to be used on m68k arch
libata: switch to dynamic allocation instead of ata_scsi_rbuf
libata: don't call ata_scsi_rbuf_fill for command without a response buffer
libata: call ->scsi_done from ata_scsi_simulate
libata: remove the done callback from ata_scsi_args
libata: move struct ata_scsi_args to libata-scsi.c
libata: avoid global response buffer in atapi_qc_complete
libata-eh: Use switch() instead of sparse array for protocol strings
ata: sata_mv: Convert to devm_ioremap_resource()
...
This update includes the usual round of major driver updates (ncr5380,
ufs, lpfc, be2iscsi, hisi_sas, storvsc, cxlflash, aacraid,
megaraid_sas, ). There's also an assortment of minor fixes and the
major update of switching a bunch of drivers to pci_alloc_irq_vectors
from Christoph.
Signed-off-by: James E.J. Bottomley <jejb@linux.vnet.ibm.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=cBQx
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI updates from James Bottomley:
"This update includes the usual round of major driver updates (ncr5380,
ufs, lpfc, be2iscsi, hisi_sas, storvsc, cxlflash, aacraid,
megaraid_sas, ...).
There's also an assortment of minor fixes and the major update of
switching a bunch of drivers to pci_alloc_irq_vectors from Christoph"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (188 commits)
scsi: megaraid_sas: handle dma_addr_t right on 32-bit
scsi: megaraid_sas: array overflow in megasas_dump_frame()
scsi: snic: switch to pci_irq_alloc_vectors
scsi: megaraid_sas: driver version upgrade
scsi: megaraid_sas: Change RAID_1_10_RMW_CMDS to RAID_1_PEER_CMDS and set value to 2
scsi: megaraid_sas: Indentation and smatch warning fixes
scsi: megaraid_sas: Cleanup VD_EXT_DEBUG and SPAN_DEBUG related debug prints
scsi: megaraid_sas: Increase internal command pool
scsi: megaraid_sas: Use synchronize_irq to wait for IRQs to complete
scsi: megaraid_sas: Bail out the driver load if ld_list_query fails
scsi: megaraid_sas: Change build_mpt_mfi_pass_thru to return void
scsi: megaraid_sas: During OCR, if get_ctrl_info fails do not continue with OCR
scsi: megaraid_sas: Do not set fp_possible if TM capable for non-RW syspdIO, change fp_possible to bool
scsi: megaraid_sas: Remove unused pd_index from megasas_build_ld_nonrw_fusion
scsi: megaraid_sas: megasas_return_cmd does not memset IO frame to zero
scsi: megaraid_sas: max_fw_cmds are decremented twice, remove duplicate
scsi: megaraid_sas: update can_queue only if the new value is less
scsi: megaraid_sas: Change max_cmd from u32 to u16 in all functions
scsi: megaraid_sas: set pd_after_lb from MR_BuildRaidContext and initialize pDevHandle to MR_DEVHANDLE_INVALID
scsi: megaraid_sas: latest controller OCR capability from FW before sending shutdown DCMD
...
Instead define the timeout behavior purely based on the host_template
eh_timed_out method and wire up the existing transport implementations
in the host templates. This also clears up the confusion that the
transport template method overrides the host template one, so some
drivers have to re-override the transport template one.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Tyrel Datwyler <tyreld@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This can be used to check for fs vs non-fs requests and basically
removes all knowledge of BLOCK_PC specific from the block layer,
as well as preparing for removing the cmd_type field in struct request.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@fb.com>
All platforms using this driver now register the SATA refclk. Remove
the hardcoded default value from the driver and instead read the rate
of the external clock and calculate the required MPY value from it.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Acked-by: Tejun Heo <tj@kernel.org>
[nsekhar@ti.com: fix checkpatch warning about an unneeded else]
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
We have a use case with the da850 SATA controller where at PLL0
frequency of 456MHz (needed to properly service the LCD controller)
the chip becomes unstable and the hardreset operation is ignored the
first time 50% of times.
The sata core driver already retries to resume the link because some
controllers ignore writes to the SControl register, but just retrying
the resume operation doesn't work - we need to issue he phy/wake reset
again to make it work.
Reimplement ahci_hardreset() in the driver and poke the controller a
couple times before really giving up.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
We need a way to retrieve the information about the online state of
the link in the ahci-da850 driver.
Create a new function: ahci_do_hardreset() which is called from
ahci_hardreset() for backwards compatibility, but has an additional
argument: 'online' - which can be used to check if the link is online
after this function returns.
The new routine will be used in the ahci-da850 driver to avoid code
duplication when implementing a workaround for tha da850 SATA
controller quirk/instability.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
There's an issue with the da850 SATA controller: if port multiplier
support is compiled in, but we're connecting the drive directly to
the SATA port on the board, the drive can't be detected.
To make SATA work on the da850-lcdk board: first try to softreset
with pmp - if the operation fails with -EBUSY, retry without pmp.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
We're using device tree for da850-lcdk. Add the match table to allow
to probe the driver.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
In preparation for using two clocks in the driver (the sysclk2-based
clock and the external REFCLK), check if we got the functional clock
after calling ahci_platform_get_resources(). If not, retry calling
clk_get() with con_id specified.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
And require all drivers that want to support BLOCK_PC to allocate it
as the first thing of their private data. To support this the legacy
IDE and BSG code is switched to set cmd_size on their queues to let
the block layer allocate the additional space.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@fb.com>
The SB600 and SB700 southbridge chips from ATI/AMD only have
connections for the primary IDE port. As these chips have unique
pci device ID's use these to mark the secondary port as 'dummy'
Signed-off-by: Darren Stevens <darren@stevens-zone.net>
Signed-off-by: Tejun Heo <tj@kernel.org>
libata-sff.c checks for legacy mode by testing if both primary and
secondary ports on a controller are in legacy mode and selects legacy
if either one is. However on some south bridge chips (e.g AMD
SB600/SB700) the secondary port is not wired, and when it is disabled
by setting the disable bit in the PCI header it appears as a fixed
legacy port.
Prevent incorrect detection by not testing ports that are marked as
'dummy'
tj: Addressed Sergei's review points. Other style edits.
Signed-off-by: Darren Stevens <darren@stevens-zone.net>
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
@t1 and @t2i are calculated along with @t2 but never used. Drop them.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: David Binderman <dcb314@hotmail.com>
Ls2088a is new introduced arm-based soc with sata support with
following features:
1. Complies with the serial ATA 3.0 specification and the AHCI 1.3.1
specification
2. Contains a high-speed descriptor-based DMA controller
3. Supports the following:
a. Speeds of 1.5 Gb/s (first-generation SATA), 3 Gb/s
(second-generation SATA), and 6 Gb/s (third-generation SATA)
b. FIS-based switching
c. Native command queuing (NCQ) commands
d. Port multiplier operation
e. Asynchronous notification
f. SATA BIST mode
Signed-off-by: Tang Yuantian <yuantian.tang@nxp.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
For ls1021a, and armv8 chasis 2 socs, sata ecc must be disabled.
If ecc register is not found in sata node in dts, report error.
This is a chip erratum described as bellow:
The Read DMA operations get early termination indication from the
controller. This issue is observed as CRC error in the status registers.
The issue is due to address collision at address 0 in the dual port
memory. The read is a dummy read to flush out the header, but due to
collision the controller logs the mbit error reported by the ECC check
logic. This results in the early termination of the Read DMA operation
by the controller. The issue happens to all the interface
speeds(GEN1/2/3) for all the products.
Workaround:
Disable ECC feature on those platforms.
Signed-off-by: Tang Yuantian <yuantian.tang@nxp.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Enable DMA coherence in SATA controller on condition that
dma-coherent property exists in sata node in DTS.
Signed-off-by: Tang Yuantian <yuantian.tang@nxp.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
This reverts commit a234f7395c.
The commit tried to get rid of the shared global SCSI response buffer.
Unfortunately, it added blocking allocation to atomic path. Revert it
for now.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Christoph Hellwig <hch@lst.de>
When CONFIG_HWMON is disabled, we now get a link failure:
ERROR: "devm_hwmon_device_register_with_groups" [drivers/ata/ahci_imx.ko] undefined!
drivers/ata/ahci_imx.o: In function `imx_ahci_probe':
ahci_imx.c:(.text.imx_ahci_probe+0x304): undefined reference to `devm_thermal_zone_of_sensor_register'
This makes the code calling into the hwmon subsystem compile-time
conditional, and adds a Kconfig dependency to avoid the corner
case of having HWMON=m and AHCI_IMX=y, by forcing AHCI_IMX=m in this
case. The thermal subsystem already has a check in its header, but
that also doesn't cover the THERMAL=m case, so we need a somewhat
complex Kconfig expression to handle all cases.
Fixes: 54643a83b4 ("ahci: imx: Add imx53 SATA temperature sensor support")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Reviewed-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Add Atari Falcon PATA controller driver. The major difference
when compared to legacy IDE's falconide host driver is that we
are using polled PIO mode and thus avoiding the need for STDMA
locking magic altogether.
Tested under ARAnyM emulator.
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
For Atari Falcon PATA support we need to check the current command
in its ->sff_data_xfer method. Update core code and all users
accordingly.
There should be no functional changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
When libata was merged m68k lacked IOMAP support. This has not been
true for a long time now so allow subsystem to be used on m68k.
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Tejun Heo <tj@kernel.org>
Note of the emulated commands in the pageout/pagein path, so just do
a GFP_NOIO dynamic allocation.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Tejun Heo <tj@kernel.org>
No need to copy a zeroed buffer to the caller if the command is defined
to not have a response in the SCSI spec.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Tejun Heo <tj@kernel.org>
We always need to call ->scsi_done after we've finished emulating a
command, so do it in a single place at the end of ata_scsi_simulate.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Tejun Heo <tj@kernel.org>
It's always the scsi_done callback, and we can get at that easily
in the place where ->done is called.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Tejun Heo <tj@kernel.org>
It's only used in libata-scsi.c, so move it closer to the users.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Tejun Heo <tj@kernel.org>
We only need to look at 4 bytes of the inquiry response for ATAPI
devices. Instead of using the global ata_scsi_rbuf just use a
a stack buffer. Also factor the fixup into it's own little helper
function to make it more readable.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Tejun Heo <tj@kernel.org>
Replace the sparse 256-pointer array for looking up protocol strings by
a switch() statement to reduce kernel size.
According to bloat-o-meter, this saves 910 bytes on m68k (32-bit), and
1892 bytes on arm64 (64-bit).
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Tejun Heo <tj@kernel.org>
Convert to devm_ioremap_resource() which provides more consistent error
handling.
Note that devm_ioremap_resource() provides its own error messages.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Here, If devm_ioremap will fail. It will return NULL.
Then hpriv->base = NULL - 0x20000; Kernel can run into
a NULL-pointer dereference. This error check will avoid
NULL pointer dereference.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: stable@vger.kernel.org
For an ATA device supporting the sense data reporting feature set, a
failed command will trigger the execution of ata_eh_request_sense if
the result task file of the failed command has the ATA_SENSE bit set
(sense data available bit). ata_eh_request_sense executes the REQUEST
SENSE DATA EXT command to retrieve the sense data of the failed
command. On success of REQUEST SENSE DATA EXT, the ATA_SENSE bit will
NOT be set (the command succeeded) but ata_eh_request_sense
nevertheless tests the availability of sense data by testing that bit
presence in the result tf of the REQUEST SENSE DATA EXT command. This
leads us to falsely assume that request sense data failed and to the
warning message:
atax.xx: request sense failed stat 50 emask 0
Upon success of REQUEST SENSE DATA EXT, set the ATA_SENSE bit in the
result task file command so that sense data can be returned by
ata_eh_request_sense.
Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: stable@vger.kernel.org
Add a hwmon entry to get the temperature from the die of imx53
SATA.
The original patch was made by Richard Zhu for kernel 2.6.x:
ENGR00134041-MX53-Add-the-SATA-AHCI-temperature-monitor.patch
Signed-off-by: Fabien Lahoudere <fabien.lahoudere@collabora.co.uk>
Signed-off-by: Tejun Heo <tj@kernel.org>
Marko reports that CX1-JB512-HP shows the same timeout issues as
CX1-JB256-HP. Let's apply MAX_SEC_128 to all devices in the series.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Marko Koski-Vähälä <marko@koski-vahala.com>
Cc: stable@vger.kernel.org # v3.19+
acpi_get_object_info() allocates the returned structure, which the
caller has to free when the call succeeds. Free it when appropriate.
Fixes: c9802a4be6 ("ata: ahci_xgene: Add AHCI Support for 2nd HW version of APM X-Gene SoC AHCI SATA Host controller.")
Signed-off-by: Michał Kępień <kernel@kempniu.pl>
Signed-off-by: Tejun Heo <tj@kernel.org>
If NO_DMA=y:
ERROR: "bad_dma_ops" [drivers/ata/libata.ko] undefined!
To fix this, protect the DMA code by #ifdef CONFIG_HAS_DMA, and provide
dummies of ata_sg_clean() and ata_sg_setup() for the !CONFIG_HAS_DMA
case.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Tejun Heo <tj@kernel.org>
Commit 70e6ad0c6d ("[PATCH] libata: prepare ata_sg_clean() for
invocation from EH") made ata_sg_clean() global, but no user outside
libata-core.c has ever materialized.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Tejun Heo <tj@kernel.org>
Pull another libata patch from Tejun Heo:
"One more patch from Adam added.
It makes libata skip probing for NCQ prio unless the feature is
explicitly requested by the user. This is necessary because some
controllers lock up after the optional feature is probed"
* 'for-4.10' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata:
ata: avoid probing NCQ Prio Support if not explicitly requested
Previously, when the ata device was being initialized we were
probing for NCQ prio support by checking the identify information
and also checking the log page that holds information about ncq prio
support.
This caused an error on an Intel HBA so the code is now updated to
only probe for NCQ prio support when the sysfs variable controlling
NCQ prio support is enabled.
tj: Update formatting, switch to spin_[un]lock_irq() and update
locking a bit, use REVALIDATE instead of RESET, and return -EIO
instead of -EINVAL on config failure.
Signed-off-by: Adam Manzanares <adam.manzanares@wdc.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Pull libata updates from Tejun Heo:
- Adam added opt-in ATA command priority support.
- There are machines which hide multiple nvme devices behind an ahci
BAR. Dan Williams proposed a solution to force-switch the mode but
deemed too hackishd. People are gonna discuss the proper way to
handle the situation in nvme standard meetings. For now, detect and
warn about the situation.
- Low level driver specific changes.
Christoph Hellwig pipes in about the hidden nvme warning:
"I wish that was the case. We've pretty much agreed that we'll want to
implement it as a virtual PCIe root bridge, similar to Intels other
'innovation' VMD that we work around that way.
But Intel management has apparently decided that they don't want to
spend more cycles on this now that Lenovo has an optional BIOS that
doesn't force this broken mode anymore, and no one outside of Intel
has enough information to implement something like this.
So for now I guess this warning is it, until Intel reconsideres and
spends resources on fixing up the damage their Chipset people caused"
* 'for-4.10' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata:
ahci: warn about remapped NVMe devices
ahci-remap.h: add ahci remapping definitions
nvme: move NVMe class code to pci_ids.h
pata: imx: support controller modes up to PIO4
pata: imx: add support of setting timings for PIO modes
pata: imx: set controller PIO mode with .set_piomode callback
pata: imx: sort headers out
ata: set ncq_prio_enabled iff device has support
ata: ATA Command Priority Disabled By Default
ata: Enabling ATA Command Priorities
block: Add iocontext priority to request
ahci: qoriq: added ls1046a platform support
It's another busy cycle for the docs tree, as the sphinx conversion
continues. Highlights include:
- Further work on PDF output, which remains a bit of a pain but should be
more solid now.
- Five more DocBook template files converted to Sphinx. Only 27 to go...
Lots of plain-text files have also been converted and integrated.
- Images in binary formats have been replaced with more source-friendly
versions.
- Various bits of organizational work, including the renaming of various
files discussed at the kernel summit.
- New documentation for the device_link mechanism.
...and, of course, lots of typo fixes and small updates.
-----BEGIN PGP SIGNATURE-----
iQIcBAABAgAGBQJYTbl7AAoJEI3ONVYwIuV63NIP/REwzThnGWFJMRSuq8Ieq2r9
sFSQsaGTGlhyKiDoEooo+SO/Za3uTonjK+e7WZg8mhdiEdamta5aociU/71C1Yy/
T9ur0FhcGblrvZ1NidSDvCLwuECZOMMei7mgLZ9a+KCpc4ANqqTVZSUm1blKcqhF
XelhVXxBa0ar35l/pVzyCxkdNXRWXv+MJZE8hp5XAdTdr11DS7UY9zrZdH31axtf
BZlbYJrvB8WPydU6myTjRpirA17Hu7uU64MsL3bNIEiRQ+nVghEzQC8uxeUCvfVx
r0H5AgGGQeir+e8GEv2T20SPZ+dumXs+y/HehKNb3jS3gV0mo+pKPeUhwLIxr+Zh
QY64gf+jYf5ISHwAJRnU0Ima72ehObzSbx9Dko10nhq2OvbR5f83gjz9t9jKYFU7
RDowICA8lwqyRbHRoVfyoW8CpVhWFpMFu3yNeJMckeTish3m7ANqzaWslbsqIP5G
zxgFMIrVVSbeae+sUeygtEJAnWI09aZ4tuaUXYtGWwu6ikC/3aV6DryP4bthG2LF
A19uV4nMrLuuh8g2wiTHHjMfjYRwvSn+f9yaolwJhwyNDXQzRPy+ZJ3W/6olOkXC
bAxTmVRCW5GA/fmSrfXmW1KbnxlWfP2C62hzZQ09UHxzTHdR97oFLDQdZhKo1uwf
pmSJR0hVeRUmA4uw6+Su
=A0EV
-----END PGP SIGNATURE-----
Merge tag 'docs-4.10' of git://git.lwn.net/linux
Pull documentation update from Jonathan Corbet:
"These are the documentation changes for 4.10.
It's another busy cycle for the docs tree, as the sphinx conversion
continues. Highlights include:
- Further work on PDF output, which remains a bit of a pain but
should be more solid now.
- Five more DocBook template files converted to Sphinx. Only 27 to
go... Lots of plain-text files have also been converted and
integrated.
- Images in binary formats have been replaced with more
source-friendly versions.
- Various bits of organizational work, including the renaming of
various files discussed at the kernel summit.
- New documentation for the device_link mechanism.
... and, of course, lots of typo fixes and small updates"
* tag 'docs-4.10' of git://git.lwn.net/linux: (193 commits)
dma-buf: Extract dma-buf.rst
Update Documentation/00-INDEX
docs: 00-INDEX: document directories/files with no docs
docs: 00-INDEX: remove non-existing entries
docs: 00-INDEX: add missing entries for documentation files/dirs
docs: 00-INDEX: consolidate process/ and admin-guide/ description
scripts: add a script to check if Documentation/00-INDEX is sane
Docs: change sh -> awk in REPORTING-BUGS
Documentation/core-api/device_link: Add initial documentation
core-api: remove an unexpected unident
ppc/idle: Add documentation for powersave=off
Doc: Correct typo, "Introdution" => "Introduction"
Documentation/atomic_ops.txt: convert to ReST markup
Documentation/local_ops.txt: convert to ReST markup
Documentation/assoc_array.txt: convert to ReST markup
docs-rst: parse-headers.pl: cleanup the documentation
docs-rst: fix media cleandocs target
docs-rst: media/Makefile: reorganize the rules
docs-rst: media: build SVG from graphviz files
docs-rst: replace bayer.png by a SVG image
...
SCT Write Same support had been introduced with
commit 7b20309428 ("libata: Add support for SCT Write Same")
Some problems, namely excessive userspace segfaults, had been reported at
http://lkml.kernel.org/r/20160908192736.GA4356@gmail.com
This lead to commit 0ce1b18c42 ("libata: Some drives failing on
SCT Write Same") which strived to disable SCT Write Same on !ZAC devices.
Due to the way this was done and to the logic in sd_config_write_same(),
this didn't work for those devices that have
->max_ws_blocks > SD_MAX_WS10_BLOCKS: for these, ->no_write_same and
->max_write_same_sectors would still be non-zero,
but ->ws10 == ->ws16 == 0. This would cause sd_setup_write_same_cmnd() to
demultiplex REQ_OP_WRITE_SAME requests to WRITE_SAME, and these in turn
aren't supported by libata-scsi:
EXT4-fs (dm-1): Delayed block allocation failed for inode 2625094 at
logical offset 2032 with max blocks 2 with error 121
EXT4-fs (dm-1): This should not happen!! Data will be lost
121 == EREMOTEIO is what scsi_io_completion() asserts in case of
invalid opcodes.
Back to the original problem of userspace segfaults: this can be tracked
down to ata_format_sct_write_same() overwriting the input page. Sometimes,
this page is ZERO_PAGE(0) which ceases to be filled with zeros from that
point on. Since ZERO_PAGE(0) is used for userspace .bss mappings, code of
the following is doomed:
static char *a = NULL; /* .bss */
...
if (a)
*a = 'a';
This problem is not solved by disabling SCT Write Same for !ZAC devices
only.
It can certainly be fixed, but the final release is quite close -- so
disable SCT Write Same for all ATA devices rather than introducing some
SCT key buffer allocation schemes at this point.
Fixes: 7b20309428 ("libata: Add support for SCT Write Same")
Signed-off-by: Nicolai Stange <nicstange@gmail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Some Intel ahci implementations have a completely broken remapping mode
where they hide one or more NVMe devices behind the bar of an AHCI device.
Intel refuses to let the OS reprogram the BIOS to switch out of this
mode at runtime, and so far we're not come up with another good way
to undo the mess that the Chipset people created. So for now the only
thing we can do is to alert users about this situation and switch to the
faster and much saner so called "AHCI" mode insted of the RAID mode in
the BIOS so that the BIOS does not hide the NVMe devices from us.
The sitation is even worse as at least one vendor (thanks a lot Lenovo..)
has started hardcoding their BIOS into the "RAID" mode even for laptops
that don't use AHCI _at all_ and just have a single NVMe device. For now
there is an unspported Linux-only BIOS that undoes this braindamage,
but we'll have to see if things are getting better or worse from here.
Based on an earlier patch from Dan Williams <dan.j.williams@intel.com>.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Tejun Heo <tj@kernel.org>
If the nr-ports property is missing ata_host_alloc_pinfo is called with
n_ports = 0. This results in host->ports[0] = NULL which later makes
mv_init_host() oops when dereferencing this pointer.
Instead be a bit more cooperative and fail the probing with an error
message.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Tejun Heo <tj@kernel.org>
Don't try to guess what the errors from pci_irq_alloc_vectors mean, as
that's too fragile. Instead always try allocating a single vector
when multi-MSI mode fails. This makes various intel Desktop and
Laptop CPUs use MSI again.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reported-by: Michael Marley <michael@michaelmarley.com>
Tested-by: Michael Marley <michael@michaelmarley.com>
Fixes: 0b9e2988ab ("ahci: use pci_alloc_irq_vectors")
Signed-off-by: Tejun Heo <tj@kernel.org>
-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJYHmoCAAoJEHm+PkMAQRiG7RMIAI2i7Y5hpL5yCxK5AFaL4u/G
KxXfp1B1UanUTgjOmd7zGqtDYcFX9t7GTTUFixQ7/9Opr4PD9qbnatoDGSc3xjbT
msDgA1B78F1/Q3kHWfeGq32MihQ4mj5NwUCo+igUcUvvWG7mHgzErj/Nh5RoobQX
p/izdpTbrw3GX6xXB8olbG7XWHaVye/+TT3q6+gmgm8I/QEujcLeGoycE0zlhPN8
FG/JX76At/+ZM2Py7Oxo3k+oKL9CHrtOQYDp/wN0uslV5eYvvkZz0/M1HMOGZt+c
gZU5jzM17K7C4Nzo06WAuBU9wUBGc25m+cPicLlOmljnzfU+f50SKaDjZq3p7QI=
=2KUF
-----END PGP SIGNATURE-----
Merge tag 'v4.9-rc4' into sound
Bring in -rc4 patches so I can successfully merge the sound doc changes.
Having timing settings for all supported by the controller PIO modes
now it is possible to expand its PIO mask.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
The controller is capable to operate in up to PIO4 mode, however
before the change the driver relies on timing settings done by
a bootloader for PIO0 mode only. The change adds more flexibility
in PIO mode selection at runtime and makes the driver to work even if
bootloader does not preset ATA timings.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Convert .set_mode callback function to more specific .set_piomode,
the driver does not have support of DMA modes, thus a simpler version
of the callback is preferred.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
There's a typo in ata_gen_passthru_sense(), where the first byte
would be overwritten incorrectly later on.
Reported-by: Charles Machalow <csm10495@gmail.com>
Signed-off-by: Hannes Reinecke <hare@suse.com>
Fixes: 11093cb1ef ("libata-scsi: generate correct ATA pass-through sense")
Cc: stable@vger.kernel.org # v4.7+
Signed-off-by: Tejun Heo <tj@kernel.org>
We need to make sure hpriv->irq is set properly if we don't use per-port
vectors, so switch from blindly assigning pdev->irq to using
pci_irq_vector, which handles all interrupt types correctly.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reported-by: Robert Richter <robert.richter@cavium.com>
Tested-by: Robert Richter <robert.richter@cavium.com>
Tested-by: David Daney <ddaney.cavm@gmail.com>
Fixes: 0b9e2988ab ("ahci: use pci_alloc_irq_vectors")
Signed-off-by: Tejun Heo <tj@kernel.org>
The previous patch renamed several files that are cross-referenced
along the Kernel documentation. Adjust the links to point to
the right places.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
commit 17a51f12 ("ahci: only try to use multi-MSI mode if there is more
than 1 port") lead to a case where nvec isn't initialized before it's
used. Fix this by moving the check into the n_ports conditional.
Reported-and-reviewed-by Colin Ian King <colin.king@canonical.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Tejun Heo <tj@kernel.org>
We previously had a check to see if the device has support for
prioritized ncq commands and a check to see if a device flag
is set, through a sysfs variable, in order to send a prioritized
command.
This patch only allows the sysfs variable to be set if the device
supports prioritized commands enabling one check in ata_build_rw_tf
in order to determine whether or not to send a prioritized command.
This patch depends on ata: ATA Command Priority Disabled By Default
tj: Minor subject and formatting updates.
Signed-off-by: Adam Manzanares <adam.manzanares@wdc.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Add a sysfs entry to turn on priority information being passed
to a ATA device. By default this feature is turned off.
This patch depends on ata: Enabling ATA Command Priorities
tj: Renamed ncq_prio_on to ncq_prio_enable and removed trivial
ata_ncq_prio_on() and open-coded the test.
Signed-off-by: Adam Manzanares <adam.manzanares@hgst.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
This patch checks to see if an ATA device supports NCQ command priorities.
If so and the user has specified an iocontext that indicates
IO_PRIO_CLASS_RT then we build a tf with a high priority command.
This is done to improve the tail latency of commands that are high
priority by passing priority to the device.
tj: Removed trivial ata_ncq_prio_enabled() and open-coded the test.
Signed-off-by: Adam Manzanares <adam.manzanares@hgst.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
We should only try to allocate multiple MSI or MSI-X vectors if the device
actually has multiple ports. Otherwise pci_alloc_irq_vectors will return
a single vector due to n_ports = 1, in which case we shouldn't set the
AHCI_HFLAG_MULTI_MSI flag.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Fixes: 0b9e2988 ("ahci: use pci_alloc_irq_vectors")
Reported-by: Emmanuel Benisty <benisty.e@gmail.com>
Tested-by: Emmanuel Benisty <benisty.e@gmail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
This reverts commit 640847298e ("ahci: qoriq: Disable NCQ
on ls2080a SoC")
The erratum has been fixed in ls2080a v2.0 and later soc.
In reality, customer will not get any ls2080a v1.0 soc. Neither apply
to any products. So reverting this commit won't create any side effect.
Blacklisting v2.0 could also be a option, but that needs to check the
soc version which is not suitable in the driver.
Signed-off-by: Tang Yuantian <yuantian.tang@nxp.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Replacing dma_pool_alloc and memset with a single call to dma_pool_zalloc
Signed-off-by: Harman Kalra <harman4linux@gmail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Restrict support SCT Write Same to devices which also support ZAC where
support is required.
Reported-by: Mike Krinkin <krinkin.m.u@gmail.com>
Signed-off-by: Shaun Tancheff <shaun.tancheff@seagate.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Use the new pci_alloc_irq_vectors API to allocate MSI-X and MSI vectors.
The big advantage over the old code is that we can use the same API for
MSI and MSI-X, and that we don't need to store the MSI-X vector mapping
in driver-private data structures.
This first conversion keeps the probe order as-is: MSI-X multi vector,
MSI multi vector, MSI single vector, MSI-X single vector and last a
single least legacy interrupt line. There is one small change of
behavior: we now check the "MSI Revert to Single Message" flag for
MSI-X in addition to MSI.
Because the API to find the Linux IRQ number for a MSI/MSI-X vector
is PCI specific, but libahaci is bus-agnostic I had to a
get_irq_vector function pointer to struct ahci_host_priv. The
alternative would be to move the multi-vector case of ahci_host_activate
to ahci.c and just call ata_host_activate directly from the others
users of ahci_host_activate.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Tejun Heo <tj@kernel.org>
Ninja32 needs to set some flags to indicate it does 32bit IO. However it currently assigns this which
loses the initializing flag and causes a warning spew. Fix it to use a logical or as is intended.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Tested-by: Ellmar Stelnberger <estellnb@elstel.org>
Signed-off-by: Tejun Heo <tj@kernel.org>
Use non DMA write log when ATA_DFLAG_PIO is set.
Signed-off-by: Shaun Tancheff <shaun.tancheff@seagate.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Acked-by: Tejun Heo <tj@kernel.org>
Correct handling of devices with sector_size other that 512 bytes.
In the case of a 4Kn device sector_size it is possible to describe a much
larger DSM Trim than the current fixed default of 512 bytes.
This patch assumes the minimum descriptor is sector_size and fills out
the descriptor accordingly.
The ACS-2 specification is quite clear that the DSM command payload is
sized as number of 512 byte transfers so a 4Kn device will operate
correctly without this patch.
Signed-off-by: Shaun Tancheff <shaun.tancheff@seagate.com>
Acked-by: Tejun Heo <tj@kernel.org>
SATA drives may support write same via SCT. This is useful
for setting the drive contents to a specific pattern (0's).
Translate a SCSI WRITE SAME 16 command to be either a DSM TRIM
command or an SCT Write Same command.
Based on the UNMAP flag:
- When set translate to DSM TRIM
- When not set translate to SCT Write Same
Signed-off-by: Shaun Tancheff <shaun.tancheff@seagate.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Acked-by: Tejun Heo <tj@kernel.org>
Safely overwriting the attached page to ATA format from the SCSI formatted
variant.
Signed-off-by: Shaun Tancheff <shaun.tancheff@seagate.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Acked-by: Tejun Heo <tj@kernel.org>
irq already contains the interrupt number for the port, don't add the
port index to it.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Tejun Heo <tj@kernel.org>
Fixes: d684a90d38 ("ahci: per-port msix support")
Cc: stable@vger.kernel.org v4.5+
Despite ST AHCI version = 1.3, reading HOST_PORTS_IMPL
returns 0. So force_port_map to 1 by using ports-implemented
DT property.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
By default the SATA IP on the qoriq SoCs does not generating
coherent/snoopable transactions. This patch enable it in the
sata axicc register.
In addition, the dma-coherent property must be set on the
SATA controller nodes.
Signed-off-by: Tang Yuantian <yuantian.tang@nxp.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
The default values for Port Phy2Cfg register and
Port Phy3Cfg register are better, no need to overwrite them.
Signed-off-by: Tang Yuantian <yuantian.tang@nxp.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
scsi_done() was called repeatedly and apparently because of that,
the kernel would call trace when we touch the Control mode page:
Call Trace:
[<ffffffff812ea0d2>] dump_stack+0x63/0x81
[<ffffffff81079cfb>] __warn+0xcb/0xf0
[<ffffffff81079e2d>] warn_slowpath_null+0x1d/0x20
[<ffffffffa00f51b0>] ata_eh_finish+0xe0/0xf0 [libata]
[<ffffffffa00fb830>] sata_pmp_error_handler+0x640/0xa50 [libata]
[<ffffffffa00470ed>] ahci_error_handler+0x1d/0x70 [libahci]
[<ffffffffa00f55f0>] ata_scsi_port_error_handler+0x430/0x770 [libata]
[<ffffffffa00eff8d>] ? ata_scsi_cmd_error_handler+0xdd/0x160 [libata]
[<ffffffffa00f59d7>] ata_scsi_error+0xa7/0xf0 [libata]
[<ffffffffa00913ba>] scsi_error_handler+0xaa/0x560 [scsi_mod]
[<ffffffffa0091310>] ? scsi_eh_get_sense+0x180/0x180 [scsi_mod]
[<ffffffff81098eb8>] kthread+0xd8/0xf0
[<ffffffff815d913f>] ret_from_fork+0x1f/0x40
[<ffffffff81098de0>] ? kthread_worker_fn+0x170/0x170
---[ end trace 8b7501047e928a17 ]---
Removed the unnecessary code and let ata_scsi_translate() do the job.
Also, since ata_mselect_control() has no ATA command to send to the
device, ata_scsi_mode_select_xlat() should return 1 for it, so that
ata_scsi_translate() will finish early to avoid ata_qc_issue().
Signed-off-by: Tom Yan <tom.ty89@gmail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
ata_mselect_*() would initialize a char array for storing a copy of
the current mode page. However, char could be signed char. In that
case, bytes larger than 127 would be converted to negative number.
For example, 0xff from def_control_mpage[] would become -1. This
prevented ata_mselect_control() from working at all, since when it
did the read-only bits check, there would always be a mismatch.
Signed-off-by: Tom Yan <tom.ty89@gmail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
- LED driver for TI LP3952 6-Channel Color LED
LED core improvements:
- Only descend into leds directory when CONFIG_NEW_LEDS is set
- Add no-op gpio_led_register_device when LED subsystem is disabled
- MAINTAINERS: Add file patterns for led device tree bindings
LED Trigger core improvements:
- return error if invalid trigger name is provided via sysfs
LED class drivers improvements
- is31fl32xx: define complete i2c_device_id table
- is31fl32xx: fix typo in id and match table names
- leds-gpio: Set of_node for created LED devices
- pca9532: Add device tree support
Conversion of IDE trigger to common disk trigger:
- leds: convert IDE trigger to common disk trigger
- leds: documentation: 'ide-disk' to 'disk-activity'
- unicore32: use the new LED disk activity trigger
- parisc: use the new LED disk activity trigger
- mips: use the new LED disk activity trigger
- arm: use the new LED disk activity trigger
- powerpc: use the new LED disk activity trigger
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.17 (GNU/Linux)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=8lmX
-----END PGP SIGNATURE-----
Merge tag 'leds_for_4.8' of git://git.kernel.org/pub/scm/linux/kernel/git/j.anaszewski/linux-leds
Pull LED updates from Jacek Anaszewski:
"New LED class driver:
- LED driver for TI LP3952 6-Channel Color LED
LED core improvements:
- Only descend into leds directory when CONFIG_NEW_LEDS is set
- Add no-op gpio_led_register_device when LED subsystem is disabled
- MAINTAINERS: Add file patterns for led device tree bindings
LED Trigger core improvements:
- return error if invalid trigger name is provided via sysfs
LED class drivers improvements
- is31fl32xx: define complete i2c_device_id table
- is31fl32xx: fix typo in id and match table names
- leds-gpio: Set of_node for created LED devices
- pca9532: Add device tree support
Conversion of IDE trigger to common disk trigger:
- leds: convert IDE trigger to common disk trigger
- leds: documentation: 'ide-disk' to 'disk-activity'
- unicore32: use the new LED disk activity trigger
- parisc: use the new LED disk activity trigger
- mips: use the new LED disk activity trigger
- arm: use the new LED disk activity trigger
- powerpc: use the new LED disk activity trigger"
* tag 'leds_for_4.8' of git://git.kernel.org/pub/scm/linux/kernel/git/j.anaszewski/linux-leds:
leds: is31fl32xx: define complete i2c_device_id table
leds: is31fl32xx: fix typo in id and match table names
leds: LED driver for TI LP3952 6-Channel Color LED
leds: leds-gpio: Set of_node for created LED devices
leds: triggers: return error if invalid trigger name is provided via sysfs
leds: Only descend into leds directory when CONFIG_NEW_LEDS is set
leds: Add no-op gpio_led_register_device when LED subsystem is disabled
unicore32: use the new LED disk activity trigger
parisc: use the new LED disk activity trigger
mips: use the new LED disk activity trigger
arm: use the new LED disk activity trigger
powerpc: use the new LED disk activity trigger
leds: documentation: 'ide-disk' to 'disk-activity'
leds: convert IDE trigger to common disk trigger
leds: pca9532: Add device tree support
MAINTAINERS: Add file patterns for led device tree bindings
Pull core block updates from Jens Axboe:
- the big change is the cleanup from Mike Christie, cleaning up our
uses of command types and modified flags. This is what will throw
some merge conflicts
- regression fix for the above for btrfs, from Vincent
- following up to the above, better packing of struct request from
Christoph
- a 2038 fix for blktrace from Arnd
- a few trivial/spelling fixes from Bart Van Assche
- a front merge check fix from Damien, which could cause issues on
SMR drives
- Atari partition fix from Gabriel
- convert cfq to highres timers, since jiffies isn't granular enough
for some devices these days. From Jan and Jeff
- CFQ priority boost fix idle classes, from me
- cleanup series from Ming, improving our bio/bvec iteration
- a direct issue fix for blk-mq from Omar
- fix for plug merging not involving the IO scheduler, like we do for
other types of merges. From Tahsin
- expose DAX type internally and through sysfs. From Toshi and Yigal
* 'for-4.8/core' of git://git.kernel.dk/linux-block: (76 commits)
block: Fix front merge check
block: do not merge requests without consulting with io scheduler
block: Fix spelling in a source code comment
block: expose QUEUE_FLAG_DAX in sysfs
block: add QUEUE_FLAG_DAX for devices to advertise their DAX support
Btrfs: fix comparison in __btrfs_map_block()
block: atari: Return early for unsupported sector size
Doc: block: Fix a typo in queue-sysfs.txt
cfq-iosched: Charge at least 1 jiffie instead of 1 ns
cfq-iosched: Fix regression in bonnie++ rewrite performance
cfq-iosched: Convert slice_resid from u64 to s64
block: Convert fifo_time from ulong to u64
blktrace: avoid using timespec
block/blk-cgroup.c: Declare local symbols static
block/bio-integrity.c: Add #include "blk.h"
block/partition-generic.c: Remove a set-but-not-used variable
block: bio: kill BIO_MAX_SIZE
cfq-iosched: temporarily boost queue priority for idle classes
block: drbd: avoid to use BIO_MAX_SIZE
block: bio: remove BIO_MAX_SECTORS
...
Pull libata updates from Tejun Heo:
"libata saw quite a bit of activities in this cycle:
- SMR drive support still being worked on
- bug fixes and improvements to misc SCSI command emulation
- some low level driver updates"
* 'for-4.8' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata: (39 commits)
libata-scsi: better style in ata_msense_*()
AHCI: Clear GHC.IS to prevent unexpectly asserting INTx
ata: sata_dwc_460ex: remove redundant dev_err call
ata: define ATA_PROT_* in terms of ATA_PROT_FLAG_*
libata: remove ATA_PROT_FLAG_DATA
libata: remove ata_is_nodata
ata: make lba_{28,48}_ok() use ATA_MAX_SECTORS{,_LBA48}
libata-scsi: minor cleanup for ata_scsi_zbc_out_xlat
libata-scsi: Fix ZBC management out command translation
libata-scsi: Fix translation of REPORT ZONES command
ata: Handle ATA NCQ NO-DATA commands correctly
libata-eh: decode all taskfile protocols
ata: fixup ATA_PROT_NODATA
libsas: use ata_is_ncq() and ata_has_dma() accessors
libata: use ata_is_ncq() accessors
libata: return boolean values from ata_is_*
libata-scsi: avoid repeated calculation of number of TRIM ranges
libata-scsi: reject WRITE SAME (16) with n_block that exceeds limit
libata-scsi: rename ata_msense_ctl_mode() to ata_msense_control()
libata-scsi: fix D_SENSE bit relection in control mode page
...
Pull libata fix from Tejun Heo:
"Another fallout from max_sectors bump a couple years ago. The lite-on
optical drive times out on large requests"
* 'for-4.7-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata:
libata: LITE-ON CX1-JB256-HP needs lower max_sectors
`changeable` is the "version" of mode page requested by the user.
It will be less confusing/misleading if we do not check it
"together" with the setting bits of the drive.
Not to mention that we currently have ata_mselect_*() implemented
in a way that each of them will serve exclusively a particular bit
on each page. The old style will hence make the condition look even
more unnecessarily arcane if the ata_msense_*() is reflecting more
than one bit.
Signed-off-by: Tom Yan <tom.ty89@gmail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Due to PCI subsystem behaviour, unloading AHCI driver will disable
MSI and enable INTx. When HBA supports MSIx or Multiple MSI, Driver's
irq handler doesn't clear GHC.IS register. It works well when reading or
writing data and GHC.IS is always non-zero. But when unloading driver
(or any other operation which causes disable MSIx and enable INTx), PCI
subsystem uses config write(Rx04.bit10) to enable INTx. Because
GHC.IS is non-zero, HBA will falsely assume some port needs interrupt
service. Then it asserts INTx. To make things worse, when AHCI controller
shares the same interrupt pin with other PCI device, that PCI device's ISR
will be called and nobody de-asserts previous INTx.
This patch clears GHC.IS in ahci_port_stop() even when using MSIx or
MMSI to prevent this case. It ensures GHC.IS is zero before PCI subsystem
enables INTx.
tj: Minor updates to the comment.
Signed-off-by: Raymond Pang <raymond_rule@hotmail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
There is a error message within devm_ioremap_resource
already, so remove the dev_err call to avoid redundant
error message.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Tejun Heo <tj@kernel.org>
This avoid the need to always translate between the two in ata_prot_flags
and generally cleans up the taskfile protocol usage.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Tejun Heo <tj@kernel.org>
The reset_all variable name is misleading as this bit is also applicable to
open, close, and finish actions. So rename that variable to "all" and remove
the unnecessary mask operation that's already done earlier.
Signed-off-by: Damien Le Moal <damien.lemoal@hgst.com>
[hch: split from the previous patch]
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Tejun Heo <tj@kernel.org>
The subcommand for NCQ NON-DATA must be specified in the feature
(low byte), not the high-order count byte. Also make sure to properly
cast the all bit to a u16 before shiting it by 8 to avoid undefined
behavior.
Signed-off-by: Damien Le Moal <damien.lemoal@hgst.com>
[hch: split the original patch into two, updated changelog]
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Tejun Heo <tj@kernel.org>
Include reporting options when translating REPORT ZONES commmand to
ATA NCQ, and make sure we only look at the actually specified bits
in the CDB for the options.
Signed-off-by: Damien Le Moal <damien.lemoal@hgst.com>
[hch: update patch description]
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Tejun Heo <tj@kernel.org>
Add a new taskfile protocol ATA_PROT_NCQ_NODATA to handle
ATA NCQ NO-DATA commands correctly.
And fixup ata_scsi_zbc_out_xlat() to use it.
Signed-off-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Tejun Heo <tj@kernel.org>
Some taskfile protocol values where missing in ata_eh_link_report().
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Tejun Heo <tj@kernel.org>
The taskfile protocol is a numeric value, and can not be ORed. Currently
this is harmless as the protocol is always zeroed before, but if it ever
has a non-zero value the ORing would create incorrect results.
Signed-off-by: Hannes Reinecke <hare@suse.de>
[hch: updated patch description]
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Tejun Heo <tj@kernel.org>
Use accessor functions instead of the raw value.
Signed-off-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Tejun Heo <tj@kernel.org>
Currently libata statically allows only 1-block (512-byte) payload
for each TRIM command. Each payload can carry 64 TRIM ranges since
each range requires 8 bytes.
It is silly to keep doing the calculation (512 / 8) in different
places. Hence, define the new ATA_MAX_TRIM_RNUM for the result.
Signed-off-by: Tom Yan <tom.ty89@gmail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Currently if a WRITE SAME (16) command is issued to the SATL with
"number of blocks" that is larger than the "Maximum write same length"
(which is the maximum number of blocks per TRIM command allowed in
libata, currently 65535 * 512 / 8 blocks), the SATL will accept the
command and translate it to a TRIM command with the upper limit.
However, according to SBC (as of sbc4r11.pdf), the "device server"
should terminate the command with "Invalid field in CDB" in that case.
Signed-off-by: Tom Yan <tom.ty89@gmail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
To make it consistent with the recently added ata_mselect_control().
We probably shouldn't have the word "mode" in its name anyway, since
that's not the case for other ata_msense_*() / ata_mselect_*() either.
Signed-off-by: Tom Yan <tom.ty89@gmail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
The bit should always be set to 1 when the requested version of
page is "changeable" because we've made it so in ata_mselect_control().
Also, it should always be set to 1 if ATA_DFLAG_D_SENSE is set (when
the requested version of page is "current" or "default").
Signed-off-by: Tom Yan <tom.ty89@gmail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
According to the HPT366 data sheet, PCI config space dword 0x40-0x43
bits 11:8 specify the primary drive cmd_high_time, however,
currently just 3 bits of the 4 are being used because the mask
is 0x700 and not 0x0f00. Fix the mask, allowing for the 40MHz clock
to be detected.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
The comment suggests we should be having an SPC-3 version descriptor
but the 0260h is the code for "SPC-2 (no version claimed)". Correct
it to 0300h so that it has the "SPC-3 (no version claimed)" descriptor.
Note that we are claiming SPC-3 version compatibility in the VERSION
field of the standard INQUIRY data. Therefore, I assume the typo was
on the code but not on the comment.
Signed-off-by: Tom Yan <tom.ty89@gmail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Avoid performance bottleneck when being SCSI pass-through'd to
virtual machines with other OSes (e.g. Windows) via virtio-scsi
and scsi-block in qemu.
Ref.: https://github.com/YanVugenfirer/kvm-guest-drivers-windows/issues/63
Signed-off-by: Tom Yan <tom.ty89@gmail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Without this fix, the DRA bit of the caching mode page would not
be updated when the read look-ahead feature is toggled (e.g. with
`smartctl --set`), but will only be until, for example, the write
cache feature is touched.
Signed-off-by: Tom Yan <tom.ty89@gmail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Commit 856c466393 ("libata: support device-managed ZAC devices")
had the line that "bumps" the VERSION field in standard INQUIRY data
removed. Add it back and claim SPC-5 version compatibility, which
matches with the current version descriptor "SPC-5 (no version claimed)"
that is used for ZAC devices.
Signed-off-by: Tom Yan <tom.ty89@gmail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
It does not make sense and is confusing to respond with "Invalid
field in CDB" while we have no support at all implemented for
FORMAT UNIT. It is decent to let it go to the default, which
will respond with "Invalid command operation code" instead.
Signed-off-by: Tom Yan <tom.ty89@gmail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Pull libata fixes from Tejun Heo:
"Two trivial fixes - one for a bug in the allocation failure path and
the other a compiler warning fix"
* 'for-4.7-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata:
ata: sata_mv: fix mis-conversion in mv_write_cached_reg()
ata: fix return value check in ahci_seattle_get_port_info()
Note that `&acdev->host->lock' and `qc->ap->lock' denote the same lock, and it's
particularly confusing to spin_lock on the former but spin_unlock on the latter.
Signed-off-by: Iago Abal <mail@iagoabal.eu>
Signed-off-by: Tejun Heo <tj@kernel.org>
This patch converts the IDE specific LED trigger to a generic disk
activity LED trigger. The libata core is now a trigger source just
like before the IDE disk driver. It's merely a replacement of the
string ide by disk.
The patch is taken from http://dev.gentoo.org/~josejx/ata.patch and is
widely used by any ibook/powerbook owners with great satisfaction.
Likewise, it is very often used successfully on different ARM platforms.
Unlike the original patch, the existing 'ide-disk' trigger is still
available for backward compatibility. That reduce the amount of patches
in affected device trees out of the mainline kernel. For further
development, the new name 'disk-activity' should be used.
Cc: Joseph Jezak <josejx@gentoo.org>
Cc: Jörg Sommer <joerg@alea.gnuu.de>
Cc: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Stephan Linz <linz@li-pro.net>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Fix the signed issue in mv_write_cached_reg() where the laddr
is assigned from a (long)addr instead of (unsigned long)addr.
Fixes the following warnings:
drivers/ata/sata_mv.c:989:26: warning: cast removes address space of expression
drivers/ata/sata_mv.c:989:26: warning: cast removes address space of expression
drivers/ata/sata_mv.c:989:26: warning: cast removes address space of expression
drivers/ata/sata_mv.c:989:26: warning: cast removes address space of expression
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Signed-off-by: Tejun Heo <tj@kernel.org>
The sysfs file for the libata error handling has multiple issues
in the way it prints time stamps:
* it prints a 9-digit nanosecond value using a %06lu format string,
which drops some leading zeroes
* it converts a 64-bit jiffes value to a timespec using
jiffies_to_timespec(), which takes a 'long' argument, so the
result is wrong after a jiffies overflow (49 days).
* we try to avoid using timespec because that generally overflows
in 2038, although this particular usage is ok.
This replaces the jiffies_to_timespec call with an open-coded
implementation that gets it right.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Tejun Heo <tj@kernel.org>
Hans de Goede
David Milburn
Matthias Brugger
Yuantian Tang
Arvind Yadav
Albert Pool
Linus Torvalds
Egor Starkov
Andy Shevchenko
Rameshwar Prasad Sahu
Greg Kroah-Hartman
Anurag Kumar Vulisha
Gustavo A. R. Silva
Colin Ian King
Kees Cook
Radha Mohan Chintakuntla
Geert Uytterhoeven
Ard Biesheuvel
Bhumika Goyal
Ville Syrjälä
Arnd Bergmann
Christoph Hellwig
Tejun Heo
Ryder Lee
Sergei Shtylyov
Ingo Molnar
Paul E. McKenney
Christophe JAILLET
Andrey Korolyov
Linus Walleij
Nate Watterson
Philipp Zabel
Julia Lawall
Jonathan Corbet
Dan Carpenter
Rob Herring
Simon Horman
Kefeng Wang
Damien Le Moal
Rafael J. Wysocki
Minwoo Im
Shawn Lin
Ondrej Zary
Doug Berger
Joe Perches
Andrew Lunn
Mauro Carvalho Chehab
Thomas Petazzoni
Sui Chen
Tycho Andersen
Bartlomiej Zolnierkiewicz
Bartosz Golaszewski
Boris Brezillon
Jason Yan
Geliang Tang
Belen Sarabia
Gwendal Grignou
Masahiro Yamada
Jens Axboe
Darren Stevens
Tang Yuantian
Geert Uytterhoeven
Uwe Kleine-König
Csaba Kertesz
Michał Kępień
Adam Manzanares
Nicolai Stange
Uwe Kleine-König
Vladimir Zapolskiy
Hannes Reinecke
Adam Manzanares
Harman Kalra
Shaun Tancheff
Alan Cox
Patrice Chotard
Tom Yan
Pang Raymond
Wei Yongjun
Damien Le Moal
Iago Abal
Stephan Linz
James Bottomley
Ben Dooks
Yendapally Reddy Dhananjaya Reddy