* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6:
b44: Use kernel DMA addresses for the kernel DMA API
forcedeth: Fix resume from hibernation regression.
xfrm: fix fragmentation on inter family tunnels
ibm_newemac: Fix dangerous struct assumption
gigaset: documentation update
gigaset: in file ops, check for device disconnect before anything else
bas_gigaset: use tasklet_hi_schedule for timing critical tasklets
net/802/fddi.c: add MODULE_LICENSE
smsc911x: remove unused #include <linux/version.h>
axnet_cs: fix phy_id detection for bogus Asix chip.
bnx2: Use request_firmware()
b44: Fix sizes passed to b44_sync_dma_desc_for_{device,cpu}()
socket: use percpu_add() while updating sockets_in_use
virtio_net: Set the mac config only when VIRITO_NET_F_MAC
myri_sbus: use request_firmware
e1000: fix loss of multicast packets
vxge: should include tcp.h
Conflict in firmware/WHENCE (SCSI vs net firmware)
The socket_post_accept() hook is not currently used by any in-tree modules
and its existence continues to cause problems by confusing people about
what can be safely accomplished using this hook. If a legitimate need for
this hook arises in the future it can always be reintroduced.
Signed-off-by: Paul Moore <paul.moore@hp.com>
Signed-off-by: James Morris <jmorris@namei.org>
* 'bkl-removal' of git://git.lwn.net/linux-2.6:
Rationalize fasync return values
Move FASYNC bit handling to f_op->fasync()
Use f_lock to protect f_flags
Rename struct file->f_ep_lock
Removing the BKL from FASYNC handling ran into the challenge of keeping the
setting of the FASYNC bit in filp->f_flags atomic with regard to calls to
the underlying fasync() function. Andi Kleen suggested moving the handling
of that bit into fasync(); this patch does exactly that. As a result, we
have a couple of internal API changes: fasync() must now manage the FASYNC
bit, and it will be called without the BKL held.
As it happens, every fasync() implementation in the kernel with one
exception calls fasync_helper(). So, if we make fasync_helper() set the
FASYNC bit, we can avoid making any changes to the other fasync()
functions - as long as those functions, themselves, have proper locking.
Most fasync() implementations do nothing but call fasync_helper() - which
has its own lock - so they are easily verified as correct. The BKL had
already been pushed down into the rest.
The networking code has its own version of fasync_helper(), so that code
has been augmented with explicit FASYNC bit handling.
Cc: Al Viro <viro@ZenIV.linux.org.uk>
Cc: David Miller <davem@davemloft.net>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
The overlap with the old SO_TIMESTAMP[NS] options is handled so
that time stamping in software (net_enable_timestamp()) is
enabled when SO_TIMESTAMP[NS] and/or SO_TIMESTAMPING_RX_SOFTWARE
is set. It's disabled if all of these are off.
Signed-off-by: Patrick Ohly <patrick.ohly@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next-2.6: (1429 commits)
net: Allow dependancies of FDDI & Tokenring to be modular.
igb: Fix build warning when DCA is disabled.
net: Fix warning fallout from recent NAPI interface changes.
gro: Fix potential use after free
sfc: If AN is enabled, always read speed/duplex from the AN advertising bits
sfc: When disabling the NIC, close the device rather than unregistering it
sfc: SFT9001: Add cable diagnostics
sfc: Add support for multiple PHY self-tests
sfc: Merge top-level functions for self-tests
sfc: Clean up PHY mode management in loopback self-test
sfc: Fix unreliable link detection in some loopback modes
sfc: Generate unique names for per-NIC workqueues
802.3ad: use standard ethhdr instead of ad_header
802.3ad: generalize out mac address initializer
802.3ad: initialize ports LACPDU from const initializer
802.3ad: remove typedef around ad_system
802.3ad: turn ports is_individual into a bool
802.3ad: turn ports is_enabled into a bool
802.3ad: make ntt bool
ixgbe: Fix set_ringparam in ixgbe to use the same memory pools.
...
Fixed trivial IPv4/6 address printing conflicts in fs/cifs/connect.c due
to the conversion to %pI (in this networking merge) and the addition of
doing IPv6 addresses (from the earlier merge of CIFS).
The kernel_accept() does not hold the module refcount of newsock->ops->owner,
so we need __module_get(newsock->ops->owner) code after call kernel_accept()
by hand.
In sunrpc, the module refcount is missing to hold. So this cause kernel panic.
Used following script to reproduct:
while [ 1 ];
do
mount -t nfs4 192.168.0.19:/ /mnt
touch /mnt/file
umount /mnt
lsmod | grep ipv6
done
This patch fixed the problem by add __module_get(newsock->ops->owner) to
kernel_accept(). So we do not need to used __module_get(newsock->ops->owner)
in every place when used kernel_accept().
Signed-off-by: Wei Yongjun <yjwei@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
fs/nfsd/nfs4recover.c
Manually fixed above to use new creds API functions, e.g.
nfs4_save_creds().
Signed-off-by: James Morris <jmorris@namei.org>
Introduce a new accept4() system call. The addition of this system call
matches analogous changes in 2.6.27 (dup3(), evenfd2(), signalfd4(),
inotify_init1(), epoll_create1(), pipe2()) which added new system calls
that differed from analogous traditional system calls in adding a flags
argument that can be used to access additional functionality.
The accept4() system call is exactly the same as accept(), except that
it adds a flags bit-mask argument. Two flags are initially implemented.
(Most of the new system calls in 2.6.27 also had both of these flags.)
SOCK_CLOEXEC causes the close-on-exec (FD_CLOEXEC) flag to be enabled
for the new file descriptor returned by accept4(). This is a useful
security feature to avoid leaking information in a multithreaded
program where one thread is doing an accept() at the same time as
another thread is doing a fork() plus exec(). More details here:
http://udrepper.livejournal.com/20407.html "Secure File Descriptor Handling",
Ulrich Drepper).
The other flag is SOCK_NONBLOCK, which causes the O_NONBLOCK flag
to be enabled on the new open file description created by accept4().
(This flag is merely a convenience, saving the use of additional calls
fcntl(F_GETFL) and fcntl (F_SETFL) to achieve the same result.
Here's a test program. Works on x86-32. Should work on x86-64, but
I (mtk) don't have a system to hand to test with.
It tests accept4() with each of the four possible combinations of
SOCK_CLOEXEC and SOCK_NONBLOCK set/clear in 'flags', and verifies
that the appropriate flags are set on the file descriptor/open file
description returned by accept4().
I tested Ulrich's patch in this thread by applying against 2.6.28-rc2,
and it passes according to my test program.
/* test_accept4.c
Copyright (C) 2008, Linux Foundation, written by Michael Kerrisk
<mtk.manpages@gmail.com>
Licensed under the GNU GPLv2 or later.
*/
#define _GNU_SOURCE
#include <unistd.h>
#include <sys/syscall.h>
#include <sys/socket.h>
#include <netinet/in.h>
#include <stdlib.h>
#include <fcntl.h>
#include <stdio.h>
#include <string.h>
#define PORT_NUM 33333
#define die(msg) do { perror(msg); exit(EXIT_FAILURE); } while (0)
/**********************************************************************/
/* The following is what we need until glibc gets a wrapper for
accept4() */
/* Flags for socket(), socketpair(), accept4() */
#ifndef SOCK_CLOEXEC
#define SOCK_CLOEXEC O_CLOEXEC
#endif
#ifndef SOCK_NONBLOCK
#define SOCK_NONBLOCK O_NONBLOCK
#endif
#ifdef __x86_64__
#define SYS_accept4 288
#elif __i386__
#define USE_SOCKETCALL 1
#define SYS_ACCEPT4 18
#else
#error "Sorry -- don't know the syscall # on this architecture"
#endif
static int
accept4(int fd, struct sockaddr *sockaddr, socklen_t *addrlen, int flags)
{
printf("Calling accept4(): flags = %x", flags);
if (flags != 0) {
printf(" (");
if (flags & SOCK_CLOEXEC)
printf("SOCK_CLOEXEC");
if ((flags & SOCK_CLOEXEC) && (flags & SOCK_NONBLOCK))
printf(" ");
if (flags & SOCK_NONBLOCK)
printf("SOCK_NONBLOCK");
printf(")");
}
printf("\n");
#if USE_SOCKETCALL
long args[6];
args[0] = fd;
args[1] = (long) sockaddr;
args[2] = (long) addrlen;
args[3] = flags;
return syscall(SYS_socketcall, SYS_ACCEPT4, args);
#else
return syscall(SYS_accept4, fd, sockaddr, addrlen, flags);
#endif
}
/**********************************************************************/
static int
do_test(int lfd, struct sockaddr_in *conn_addr,
int closeonexec_flag, int nonblock_flag)
{
int connfd, acceptfd;
int fdf, flf, fdf_pass, flf_pass;
struct sockaddr_in claddr;
socklen_t addrlen;
printf("=======================================\n");
connfd = socket(AF_INET, SOCK_STREAM, 0);
if (connfd == -1)
die("socket");
if (connect(connfd, (struct sockaddr *) conn_addr,
sizeof(struct sockaddr_in)) == -1)
die("connect");
addrlen = sizeof(struct sockaddr_in);
acceptfd = accept4(lfd, (struct sockaddr *) &claddr, &addrlen,
closeonexec_flag | nonblock_flag);
if (acceptfd == -1) {
perror("accept4()");
close(connfd);
return 0;
}
fdf = fcntl(acceptfd, F_GETFD);
if (fdf == -1)
die("fcntl:F_GETFD");
fdf_pass = ((fdf & FD_CLOEXEC) != 0) ==
((closeonexec_flag & SOCK_CLOEXEC) != 0);
printf("Close-on-exec flag is %sset (%s); ",
(fdf & FD_CLOEXEC) ? "" : "not ",
fdf_pass ? "OK" : "failed");
flf = fcntl(acceptfd, F_GETFL);
if (flf == -1)
die("fcntl:F_GETFD");
flf_pass = ((flf & O_NONBLOCK) != 0) ==
((nonblock_flag & SOCK_NONBLOCK) !=0);
printf("nonblock flag is %sset (%s)\n",
(flf & O_NONBLOCK) ? "" : "not ",
flf_pass ? "OK" : "failed");
close(acceptfd);
close(connfd);
printf("Test result: %s\n", (fdf_pass && flf_pass) ? "PASS" : "FAIL");
return fdf_pass && flf_pass;
}
static int
create_listening_socket(int port_num)
{
struct sockaddr_in svaddr;
int lfd;
int optval;
memset(&svaddr, 0, sizeof(struct sockaddr_in));
svaddr.sin_family = AF_INET;
svaddr.sin_addr.s_addr = htonl(INADDR_ANY);
svaddr.sin_port = htons(port_num);
lfd = socket(AF_INET, SOCK_STREAM, 0);
if (lfd == -1)
die("socket");
optval = 1;
if (setsockopt(lfd, SOL_SOCKET, SO_REUSEADDR, &optval,
sizeof(optval)) == -1)
die("setsockopt");
if (bind(lfd, (struct sockaddr *) &svaddr,
sizeof(struct sockaddr_in)) == -1)
die("bind");
if (listen(lfd, 5) == -1)
die("listen");
return lfd;
}
int
main(int argc, char *argv[])
{
struct sockaddr_in conn_addr;
int lfd;
int port_num;
int passed;
passed = 1;
port_num = (argc > 1) ? atoi(argv[1]) : PORT_NUM;
memset(&conn_addr, 0, sizeof(struct sockaddr_in));
conn_addr.sin_family = AF_INET;
conn_addr.sin_addr.s_addr = htonl(INADDR_LOOPBACK);
conn_addr.sin_port = htons(port_num);
lfd = create_listening_socket(port_num);
if (!do_test(lfd, &conn_addr, 0, 0))
passed = 0;
if (!do_test(lfd, &conn_addr, SOCK_CLOEXEC, 0))
passed = 0;
if (!do_test(lfd, &conn_addr, 0, SOCK_NONBLOCK))
passed = 0;
if (!do_test(lfd, &conn_addr, SOCK_CLOEXEC, SOCK_NONBLOCK))
passed = 0;
close(lfd);
exit(passed ? EXIT_SUCCESS : EXIT_FAILURE);
}
[mtk.manpages@gmail.com: rewrote changelog, updated test program]
Signed-off-by: Ulrich Drepper <drepper@redhat.com>
Tested-by: Michael Kerrisk <mtk.manpages@gmail.com>
Acked-by: Michael Kerrisk <mtk.manpages@gmail.com>
Cc: <linux-api@vger.kernel.org>
Cc: <linux-arch@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Wrap access to task credentials so that they can be separated more easily from
the task_struct during the introduction of COW creds.
Change most current->(|e|s|fs)[ug]id to current_(|e|s|fs)[ug]id().
Change some task->e?[ug]id to task_e?[ug]id(). In some places it makes more
sense to use RCU directly rather than a convenient wrapper; these will be
addressed by later patches.
Signed-off-by: David Howells <dhowells@redhat.com>
Reviewed-by: James Morris <jmorris@namei.org>
Acked-by: Serge Hallyn <serue@us.ibm.com>
Cc: netdev@vger.kernel.org
Signed-off-by: James Morris <jmorris@namei.org>
Removed duplicated #include <rdma/ib_verbs.h> in net/9p/trans_rdma.c
and #include <linux/thread_info.h> in net/socket.c
Signed-off-by: Jianjun Kong <jianjun@zeuux.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
As it is, all instances of ->release() for files that have ->fasync()
need to remember to evict file from fasync lists; forgetting that
creates a hole and we actually have a bunch that *does* forget.
So let's keep our lives simple - let __fput() check FASYNC in
file->f_flags and call ->fasync() there if it's been set. And lose that
crap in ->release() instances - leaving it there is still valid, but we
don't have to bother anymore.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Some code here depends on CONFIG_KMOD to not try to load
protocol modules or similar, replace by CONFIG_MODULES
where more than just request_module depends on CONFIG_KMOD
and and also use try_then_request_module in ebtables.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
The reasons for disabling paccept() are as follows:
* The API is more complex than needed. There is AFAICS no demonstrated
use case that the sigset argument of this syscall serves that couldn't
equally be served by the use of pselect/ppoll/epoll_pwait + traditional
accept(). Roland seems to concur with this opinion
(http://thread.gmane.org/gmane.linux.kernel/723953/focus=732255). I
have (more than once) asked Ulrich to explain otherwise
(http://thread.gmane.org/gmane.linux.kernel/723952/focus=731018), but he
does not respond, so one is left to assume that he doesn't know of such
a case.
* The use of a sigset argument is not consistent with other I/O APIs
that can block on a single file descriptor (e.g., read(), recv(),
connect()).
* The behavior of paccept() when interrupted by a signal is IMO strange:
the kernel restarts the system call if SA_RESTART was set for the
handler. I think that it should not do this -- that it should behave
consistently with paccept()/ppoll()/epoll_pwait(), which never restart,
regardless of SA_RESTART. The reasoning here is that the very purpose
of paccept() is to wait for a connection or a signal, and that
restarting in the latter case is probably never useful. (Note: Roland
disagrees on this point, believing that rather paccept() should be
consistent with accept() in its behavior wrt EINTR
(http://thread.gmane.org/gmane.linux.kernel/723953/focus=732255).)
I believe that instead, a simpler API, consistent with Ulrich's other
recent additions, is preferable:
accept4(int fd, struct sockaddr *sa, socklen_t *salen, ind flags);
(This simpler API was originally proposed by Ulrich:
http://thread.gmane.org/gmane.linux.network/92072)
If this simpler API is added, then if we later decide that the sigset
argument really is required, then a suitable bit in 'flags' could be added
to indicate the presence of the sigset argument.
At this point, I am hoping we either will get a counter-argument from
Ulrich about why we really do need paccept()'s sigset argument, or that he
will resubmit the original accept4() patch.
Signed-off-by: Michael Kerrisk <mtk.manpages@gmail.com>
Cc: David Miller <davem@davemloft.net>
Cc: Davide Libenzi <davidel@xmailserver.org>
Cc: Alan Cox <alan@redhat.com>
Cc: Ulrich Drepper <drepper@redhat.com>
Cc: Jakub Jelinek <jakub@redhat.com>
Cc: Roland McGrath <roland@redhat.com>
Cc: Oleg Nesterov <oleg@tv-sign.ru>
Cc: Christoph Hellwig <hch@lst.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Kmem cache passed to constructor is only needed for constructors that are
themselves multiplexeres. Nobody uses this "feature", nor does anybody uses
passed kmem cache in non-trivial way, so pass only pointer to object.
Non-trivial places are:
arch/powerpc/mm/init_64.c
arch/powerpc/mm/hugetlbpage.c
This is flag day, yes.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Acked-by: Pekka Enberg <penberg@cs.helsinki.fi>
Acked-by: Christoph Lameter <cl@linux-foundation.org>
Cc: Jon Tollefson <kniht@linux.vnet.ibm.com>
Cc: Nick Piggin <nickpiggin@yahoo.com.au>
Cc: Matt Mackall <mpm@selenic.com>
[akpm@linux-foundation.org: fix arch/powerpc/mm/hugetlbpage.c]
[akpm@linux-foundation.org: fix mm/slab.c]
[akpm@linux-foundation.org: fix ubifs]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch adds test that ensure the boundary conditions for the various
constants introduced in the previous patches is met. No code is generated.
[akpm@linux-foundation.org: fix alpha]
Signed-off-by: Ulrich Drepper <drepper@redhat.com>
Acked-by: Davide Libenzi <davidel@xmailserver.org>
Cc: Michael Kerrisk <mtk.manpages@googlemail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Some platforms do not have support to restore the signal mask in the
return path from a syscall. For those platforms syscalls like pselect are
not defined at all. This is, I think, not a good choice for paccept()
since paccept() adds more value on top of accept() than just the signal
mask handling.
Therefore this patch defines a scaled down version of the sys_paccept
function for those platforms. It returns -EINVAL in case the signal mask
is non-NULL but behaves the same otherwise.
Note that I explicitly included <linux/thread_info.h>. I saw that it is
currently included but indirectly two levels down. There is too much risk
in relying on this. The header might change and then suddenly the
function definition would change without anyone immediately noticing.
Signed-off-by: Ulrich Drepper <drepper@redhat.com>
Cc: Davide Libenzi <davidel@xmailserver.org>
Cc: Michael Kerrisk <mtk.manpages@googlemail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch is by far the most complex in the series. It adds a new syscall
paccept. This syscall differs from accept in that it adds (at the userlevel)
two additional parameters:
- a signal mask
- a flags value
The flags parameter can be used to set flag like SOCK_CLOEXEC. This is
imlpemented here as well. Some people argued that this is a property which
should be inherited from the file desriptor for the server but this is against
POSIX. Additionally, we really want the signal mask parameter as well
(similar to pselect, ppoll, etc). So an interface change in inevitable.
The flag value is the same as for socket and socketpair. I think diverging
here will only create confusion. Similar to the filesystem interfaces where
the use of the O_* constants differs, it is acceptable here.
The signal mask is handled as for pselect etc. The mask is temporarily
installed for the thread and removed before the call returns. I modeled the
code after pselect. If there is a problem it's likely also in pselect.
For architectures which use socketcall I maintained this interface instead of
adding a system call. The symmetry shouldn't be broken.
The following test must be adjusted for architectures other than x86 and
x86-64 and in case the syscall numbers changed.
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
#include <errno.h>
#include <fcntl.h>
#include <pthread.h>
#include <signal.h>
#include <stdio.h>
#include <unistd.h>
#include <netinet/in.h>
#include <sys/socket.h>
#include <sys/syscall.h>
#ifndef __NR_paccept
# ifdef __x86_64__
# define __NR_paccept 288
# elif defined __i386__
# define SYS_PACCEPT 18
# define USE_SOCKETCALL 1
# else
# error "need __NR_paccept"
# endif
#endif
#ifdef USE_SOCKETCALL
# define paccept(fd, addr, addrlen, mask, flags) \
({ long args[6] = { \
(long) fd, (long) addr, (long) addrlen, (long) mask, 8, (long) flags }; \
syscall (__NR_socketcall, SYS_PACCEPT, args); })
#else
# define paccept(fd, addr, addrlen, mask, flags) \
syscall (__NR_paccept, fd, addr, addrlen, mask, 8, flags)
#endif
#define PORT 57392
#define SOCK_CLOEXEC O_CLOEXEC
static pthread_barrier_t b;
static void *
tf (void *arg)
{
pthread_barrier_wait (&b);
int s = socket (AF_INET, SOCK_STREAM, 0);
struct sockaddr_in sin;
sin.sin_family = AF_INET;
sin.sin_addr.s_addr = htonl (INADDR_LOOPBACK);
sin.sin_port = htons (PORT);
connect (s, (const struct sockaddr *) &sin, sizeof (sin));
close (s);
pthread_barrier_wait (&b);
s = socket (AF_INET, SOCK_STREAM, 0);
sin.sin_port = htons (PORT);
connect (s, (const struct sockaddr *) &sin, sizeof (sin));
close (s);
pthread_barrier_wait (&b);
pthread_barrier_wait (&b);
sleep (2);
pthread_kill ((pthread_t) arg, SIGUSR1);
return NULL;
}
static void
handler (int s)
{
}
int
main (void)
{
pthread_barrier_init (&b, NULL, 2);
struct sockaddr_in sin;
pthread_t th;
if (pthread_create (&th, NULL, tf, (void *) pthread_self ()) != 0)
{
puts ("pthread_create failed");
return 1;
}
int s = socket (AF_INET, SOCK_STREAM, 0);
int reuse = 1;
setsockopt (s, SOL_SOCKET, SO_REUSEADDR, &reuse, sizeof (reuse));
sin.sin_family = AF_INET;
sin.sin_addr.s_addr = htonl (INADDR_LOOPBACK);
sin.sin_port = htons (PORT);
bind (s, (struct sockaddr *) &sin, sizeof (sin));
listen (s, SOMAXCONN);
pthread_barrier_wait (&b);
int s2 = paccept (s, NULL, 0, NULL, 0);
if (s2 < 0)
{
puts ("paccept(0) failed");
return 1;
}
int coe = fcntl (s2, F_GETFD);
if (coe & FD_CLOEXEC)
{
puts ("paccept(0) set close-on-exec-flag");
return 1;
}
close (s2);
pthread_barrier_wait (&b);
s2 = paccept (s, NULL, 0, NULL, SOCK_CLOEXEC);
if (s2 < 0)
{
puts ("paccept(SOCK_CLOEXEC) failed");
return 1;
}
coe = fcntl (s2, F_GETFD);
if ((coe & FD_CLOEXEC) == 0)
{
puts ("paccept(SOCK_CLOEXEC) does not set close-on-exec flag");
return 1;
}
close (s2);
pthread_barrier_wait (&b);
struct sigaction sa;
sa.sa_handler = handler;
sa.sa_flags = 0;
sigemptyset (&sa.sa_mask);
sigaction (SIGUSR1, &sa, NULL);
sigset_t ss;
pthread_sigmask (SIG_SETMASK, NULL, &ss);
sigaddset (&ss, SIGUSR1);
pthread_sigmask (SIG_SETMASK, &ss, NULL);
sigdelset (&ss, SIGUSR1);
alarm (4);
pthread_barrier_wait (&b);
errno = 0 ;
s2 = paccept (s, NULL, 0, &ss, 0);
if (s2 != -1 || errno != EINTR)
{
puts ("paccept did not fail with EINTR");
return 1;
}
close (s);
puts ("OK");
return 0;
}
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
[akpm@linux-foundation.org: make it compile]
[akpm@linux-foundation.org: add sys_ni stub]
Signed-off-by: Ulrich Drepper <drepper@redhat.com>
Acked-by: Davide Libenzi <davidel@xmailserver.org>
Cc: Michael Kerrisk <mtk.manpages@googlemail.com>
Cc: <linux-arch@vger.kernel.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Roland McGrath <roland@redhat.com>
Cc: Kyle McMartin <kyle@mcmartin.ca>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch adds support for flag values which are ORed to the type passwd
to socket and socketpair. The additional code is minimal. The flag
values in this implementation can and must match the O_* flags. This
avoids overhead in the conversion.
The internal functions sock_alloc_fd and sock_map_fd get a new parameters
and all callers are changed.
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
#include <fcntl.h>
#include <stdio.h>
#include <unistd.h>
#include <netinet/in.h>
#include <sys/socket.h>
#define PORT 57392
/* For Linux these must be the same. */
#define SOCK_CLOEXEC O_CLOEXEC
int
main (void)
{
int fd;
fd = socket (PF_INET, SOCK_STREAM, 0);
if (fd == -1)
{
puts ("socket(0) failed");
return 1;
}
int coe = fcntl (fd, F_GETFD);
if (coe == -1)
{
puts ("fcntl failed");
return 1;
}
if (coe & FD_CLOEXEC)
{
puts ("socket(0) set close-on-exec flag");
return 1;
}
close (fd);
fd = socket (PF_INET, SOCK_STREAM|SOCK_CLOEXEC, 0);
if (fd == -1)
{
puts ("socket(SOCK_CLOEXEC) failed");
return 1;
}
coe = fcntl (fd, F_GETFD);
if (coe == -1)
{
puts ("fcntl failed");
return 1;
}
if ((coe & FD_CLOEXEC) == 0)
{
puts ("socket(SOCK_CLOEXEC) does not set close-on-exec flag");
return 1;
}
close (fd);
int fds[2];
if (socketpair (PF_UNIX, SOCK_STREAM, 0, fds) == -1)
{
puts ("socketpair(0) failed");
return 1;
}
for (int i = 0; i < 2; ++i)
{
coe = fcntl (fds[i], F_GETFD);
if (coe == -1)
{
puts ("fcntl failed");
return 1;
}
if (coe & FD_CLOEXEC)
{
printf ("socketpair(0) set close-on-exec flag for fds[%d]\n", i);
return 1;
}
close (fds[i]);
}
if (socketpair (PF_UNIX, SOCK_STREAM|SOCK_CLOEXEC, 0, fds) == -1)
{
puts ("socketpair(SOCK_CLOEXEC) failed");
return 1;
}
for (int i = 0; i < 2; ++i)
{
coe = fcntl (fds[i], F_GETFD);
if (coe == -1)
{
puts ("fcntl failed");
return 1;
}
if ((coe & FD_CLOEXEC) == 0)
{
printf ("socketpair(SOCK_CLOEXEC) does not set close-on-exec flag for fds[%d]\n", i);
return 1;
}
close (fds[i]);
}
puts ("OK");
return 0;
}
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Signed-off-by: Ulrich Drepper <drepper@redhat.com>
Acked-by: Davide Libenzi <davidel@xmailserver.org>
Cc: Michael Kerrisk <mtk.manpages@googlemail.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Use sockaddr_storage{} for generic socket address storage
and ensures proper alignment.
Use sockaddr{} for pointers to omit several casts.
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Next we can kill the hacks in fs/compat_ioctl.c and also
dispatch compat ioctls down into the driver and 80211 protocol
helper layers in order to handle iw_point objects embedded in
stream replies which need to be translated.
Signed-off-by: David S. Miller <davem@davemloft.net>
After the removal of the Solaris binary emulation the exports of
move_addr_to_{kernel,user} are no longer used.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
There's already some stuff on the struct net, that should better
be folded into netns_core structure. I'm making the per-proto inuse
counter be per-net also, which is also a candidate for this, so
introduce this structure and populate it a bit.
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce per-sock inlines: sock_net(), sock_net_set()
and per-inet_timewait_sock inlines: twsk_net(), twsk_net_set().
Without CONFIG_NET_NS, no namespace other than &init_net exists.
Let's explicitly define them to help compiler optimizations.
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
This is a narrow pedantry :) but the dlci_ioctl_hook check and call
should not be parted with the mutex lock.
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes a segmentation fault when trying to splice from a non-TCP socket.
Signed-off-by: Rémi Denis-Courmont <rdenis@simphalempin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Just move the variable on the struct net and adjust
its usage.
Others sysctls from sys.net.core table are more
difficult to virtualize (i.e. make them per-namespace),
but I'll look at them as well a bit later.
Signed-off-by: Pavel Emelyanov <xemul@oenvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The sock_wake_async() performs a bit different actions
depending on "how" argument. Unfortunately this argument
ony has numerical magic values.
I propose to give names to their constants to help people
reading this function callers understand what's going on
without looking into this function all the time.
I suppose this is 2.6.25 material, but if it's not (or the
naming seems poor/bad/awful), I can rework it against the
current net-2.6 tree.
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some time ago a sockfd_lookup_light was introduced and
most of the socket.c file was patched to use it. However
two routines were left - sys_sendto and sys_recvfrom.
Patch them as well, since this helper does exactly what
these two need.
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
...and fix a couple of bugs in the NBD, CIFS and OCFS2 socket handlers.
Looking at the sock->op->shutdown() handlers, it looks as if all of them
take a SHUT_RD/SHUT_WR/SHUT_RDWR argument instead of the
RCV_SHUTDOWN/SEND_SHUTDOWN arguments.
Add a helper, and then define the SHUT_* enum to ensure that kernel users
of shutdown() don't get confused.
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Acked-by: Mark Fasheh <mark.fasheh@oracle.com>
Acked-by: David Howells <dhowells@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If either of the two sock_alloc_fd() calls fail, we
forget to update 'err' and thus we'll erroneously
return zero in these cases.
Based upon a report and patch from Rich Paul, and
commentary from Chuck Ebbert.
Signed-off-by: David S. Miller <davem@davemloft.net>
Why do we need r/o bind mounts?
This feature allows a read-only view into a read-write filesystem. In the
process of doing that, it also provides infrastructure for keeping track of
the number of writers to any given mount.
This has a number of uses. It allows chroots to have parts of filesystems
writable. It will be useful for containers in the future because users may
have root inside a container, but should not be allowed to write to
somefilesystems. This also replaces patches that vserver has had out of the
tree for several years.
It allows security enhancement by making sure that parts of your filesystem
read-only (such as when you don't trust your FTP server), when you don't want
to have entire new filesystems mounted, or when you want atime selectively
updated. I've been using the following script to test that the feature is
working as desired. It takes a directory and makes a regular bind and a r/o
bind mount of it. It then performs some normal filesystem operations on the
three directories, including ones that are expected to fail, like creating a
file on the r/o mount.
This patch:
Some filesystems forego the vfs and may_open() and create their own 'struct
file's.
This patch creates a couple of helper functions which can be used by these
filesystems, and will provide a unified place which the r/o bind mount code
may patch.
Also, rename an existing, static-scope init_file() to a less generic name.
Signed-off-by: Dave Hansen <haveblue@us.ibm.com>
Cc: Christoph Hellwig <hch@lst.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Slab constructors currently have a flags parameter that is never used. And
the order of the arguments is opposite to other slab functions. The object
pointer is placed before the kmem_cache pointer.
Convert
ctor(void *object, struct kmem_cache *s, unsigned long flags)
to
ctor(struct kmem_cache *s, void *object)
throughout the kernel
[akpm@linux-foundation.org: coupla fixes]
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
If kernel_accept() returns an error, it may pass back a pointer to
freed memory (which the caller should ignore). Make it pass back NULL
instead for better safety.
Signed-off-by: Tony Battersby <tonyb@cybernetics.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix a bunch of sparse warnings. Mostly about 0 used as
NULL pointer, and shadowed variable declarations.
One notable case was that hash size should have been unsigned.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch makes most of the generic device layer network
namespace safe. This patch makes dev_base_head a
network namespace variable, and then it picks up
a few associated variables. The functions:
dev_getbyhwaddr
dev_getfirsthwbytype
dev_get_by_flags
dev_get_by_name
__dev_get_by_name
dev_get_by_index
__dev_get_by_index
dev_ioctl
dev_ethtool
dev_load
wireless_process_ioctl
were modified to take a network namespace argument, and
deal with it.
vlan_ioctl_set and brioctl_set were modified so their
hooks will receive a network namespace argument.
So basically anthing in the core of the network stack that was
affected to by the change of dev_base was modified to handle
multiple network namespaces. The rest of the network stack was
simply modified to explicitly use &init_net the initial network
namespace. This can be fixed when those components of the network
stack are modified to handle multiple network namespaces.
For now the ifindex generator is left global.
Fundametally ifindex numbers are per namespace, or else
we will have corner case problems with migration when
we get that far.
At the same time there are assumptions in the network stack
that the ifindex of a network device won't change. Making
the ifindex number global seems a good compromise until
the network stack can cope with ifindex changes when
you change namespaces, and the like.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds
Eric Dumazet
Paul Moore
Al Viro
Jonathan Corbet
Patrick Ohly
Heiko Carstens
James Morris
David S. Miller
Wei Yongjun
Ulrich Drepper
David Howells
Jianjun Kong
Johannes Berg
Michael Kerrisk
Alexey Dobriyan
YOSHIFUJI Hideaki
Adrian Bunk
Pavel Emelyanov
Rémi Denis-Courmont
Jens Axboe
Trond Myklebust
David S. Miller
Dave Hansen
Christoph Lameter
Tony Battersby
Stephen Hemminger
Eric W. Biederman