Граф коммитов

1570 Коммитов

Автор SHA1 Сообщение Дата
Quentin Schulz 3fa528b768 net: phy: mscc: fix deadlock in vsc85xx_default_config
The vsc85xx_default_config function called in the vsc85xx_config_init
function which is used by VSC8530, VSC8531, VSC8540 and VSC8541 PHYs
mistakenly calls phy_read and phy_write in-between phy_select_page and
phy_restore_page.

phy_select_page and phy_restore_page actually take and release the MDIO
bus lock and phy_write and phy_read take and release the lock to write
or read to a PHY register.

Let's fix this deadlock by using phy_modify_paged which handles
correctly a read followed by a write in a non-standard page.

Fixes: 6a0bfbbe20 ("net: phy: mscc: migrate to phy_select/restore_page functions")
Signed-off-by: Quentin Schulz <quentin.schulz@bootlin.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
2018-11-23 22:34:40 -08:00
Martin Schiller df5a8ec64e net: phy: mdio-gpio: Fix working over slow can_sleep GPIOs
Up until commit 7e5fbd1e07 ("net: mdio-gpio: Convert to use gpiod
functions where possible"), the _cansleep variants of the gpio_ API was
used. After that commit and the change to gpiod_ API, the _cansleep()
was dropped. This then results in WARN_ON() when used with GPIO
devices which do sleep. Add back the _cansleep() to avoid this.

Fixes: 7e5fbd1e07 ("net: mdio-gpio: Convert to use gpiod functions where possible")
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2018-11-17 21:11:51 -08:00
David S. Miller 160396a722 Revert "net: phy: mdio-gpio: Fix working over slow can_sleep GPIOs"
This reverts commit dfa0d55ff6.

Discussion still ongoing, I shouldn't have applied this.

Signed-off-by: David S. Miller <davem@davemloft.net>
2018-11-16 23:04:37 -08:00
Martin Schiller dfa0d55ff6 net: phy: mdio-gpio: Fix working over slow can_sleep GPIOs
This commit re-enables support for slow GPIO pins. It was initially
introduced by commit 2d6c9091ab ("net: mdio-gpio: support access that
may sleep") and got lost by commit 7e5fbd1e07 ("net: mdio-gpio:
Convert to use gpiod functions where possible").

Also add a warning about slow GPIO pins like it is done in i2c-gpio.

Signed-off-by: Martin Schiller <ms@dev.tdt.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
2018-11-16 20:25:22 -08:00
Tao Ren 042cb56478 net: phy: Allow BCM54616S PHY to setup internal TX/RX clock delay
This patch allows users to enable/disable internal TX and/or RX clock
delay for BCM54616S PHYs so as to satisfy RGMII timing specifications.

On a particular platform, whether TX and/or RX clock delay is required
depends on how PHY connected to the MAC IP. This requirement can be
specified through "phy-mode" property in the platform device tree.

The patch is inspired by commit 733336262b ("net: phy: Allow BCM5481x
PHYs to setup internal TX/RX clock delay").

Signed-off-by: Tao Ren <taoren@fb.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2018-11-06 11:16:58 -08:00
Holger Hoffstätte 0432e83319 net: phy: realtek: fix RTL8201F sysfs name
Since 4.19 the following error in sysfs has appeared when using the
r8169 NIC driver:

$cd /sys/module/realtek/drivers
$ls -l
ls: cannot access 'mdio_bus:RTL8201F 10/100Mbps Ethernet': No such file or directory
[..garbled dir entries follow..]

Apparently the forward slash in "10/100Mbps Ethernet" is interpreted
as directory separator that leads nowhere, and was introduced in commit
513588dd44 ("net: phy: realtek: add RTL8201F phy-id and functions").

Fix this by removing the offending slash in the driver name.

Other drivers in net/phy seem to have the same problem, but I cannot
test/verify them.

Fixes: 513588dd44 ("net: phy: realtek: add RTL8201F phy-id and functions")
Signed-off-by: Holger Hoffstätte <holger@applied-asynchrony.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
2018-11-04 16:43:17 -08:00
Andrew Lunn f802912d42 net: phy: genphy_10g_driver: Avoid NULL pointer dereference
This driver got missed during the recent change of .features from a
u32 to a pointer to a Linux bitmap. Change the initialisation from 0
to PHY_10GBIT_FEATURES so removing the danger of a NULL pointer
dereference.

Fixes: 719655a149 ("net: phy: Replace phy driver features u32 with link_mode bitmap")
Reported-by: Jose Abreu <jose.abreu@synopsys.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
2018-10-25 16:19:09 -07:00
Linus Torvalds 50b825d7e8 Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next
Pull networking updates from David Miller:

 1) Add VF IPSEC offload support in ixgbe, from Shannon Nelson.

 2) Add zero-copy AF_XDP support to i40e, from Björn Töpel.

 3) All in-tree drivers are converted to {g,s}et_link_ksettings() so we
    can get rid of the {g,s}et_settings ethtool callbacks, from Michal
    Kubecek.

 4) Add software timestamping to veth driver, from Michael Walle.

 5) More work to make packet classifiers and actions lockless, from Vlad
    Buslov.

 6) Support sticky FDB entries in bridge, from Nikolay Aleksandrov.

 7) Add ipv6 version of IP_MULTICAST_ALL sockopt, from Andre Naujoks.

 8) Support batching of XDP buffers in vhost_net, from Jason Wang.

 9) Add flow dissector BPF hook, from Petar Penkov.

10) i40e vf --> generic iavf conversion, from Jesse Brandeburg.

11) Add NLA_REJECT netlink attribute policy type, to signal when users
    provide attributes in situations which don't make sense. From
    Johannes Berg.

12) Switch TCP and fair-queue scheduler over to earliest departure time
    model. From Eric Dumazet.

13) Improve guest receive performance by doing rx busy polling in tx
    path of vhost networking driver, from Tonghao Zhang.

14) Add per-cgroup local storage to bpf

15) Add reference tracking to BPF, from Joe Stringer. The verifier can
    now make sure that references taken to objects are properly released
    by the program.

16) Support in-place encryption in TLS, from Vakul Garg.

17) Add new taprio packet scheduler, from Vinicius Costa Gomes.

18) Lots of selftests additions, too numerous to mention one by one here
    but all of which are very much appreciated.

19) Support offloading of eBPF programs containing BPF to BPF calls in
    nfp driver, frm Quentin Monnet.

20) Move dpaa2_ptp driver out of staging, from Yangbo Lu.

21) Lots of u32 classifier cleanups and simplifications, from Al Viro.

22) Add new strict versions of netlink message parsers, and enable them
    for some situations. From David Ahern.

23) Evict neighbour entries on carrier down, also from David Ahern.

24) Support BPF sk_msg verdict programs with kTLS, from Daniel Borkmann
    and John Fastabend.

25) Add support for filtering route dumps, from David Ahern.

26) New igc Intel driver for 2.5G parts, from Sasha Neftin et al.

27) Allow vxlan enslavement to bridges in mlxsw driver, from Ido
    Schimmel.

28) Add queue and stack map types to eBPF, from Mauricio Vasquez B.

29) Add back byte-queue-limit support to r8169, with all the bug fixes
    in other areas of the driver it works now! From Florian Westphal and
    Heiner Kallweit.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (2147 commits)
  tcp: add tcp_reset_xmit_timer() helper
  qed: Fix static checker warning
  Revert "be2net: remove desc field from be_eq_obj"
  Revert "net: simplify sock_poll_wait"
  net: socionext: Reset tx queue in ndo_stop
  net: socionext: Add dummy PHY register read in phy_write()
  net: socionext: Stop PHY before resetting netsec
  net: stmmac: Set OWN bit for jumbo frames
  arm64: dts: stratix10: Support Ethernet Jumbo frame
  tls: Add maintainers
  net: ethernet: ti: cpsw: unsync mcast entries while switch promisc mode
  octeontx2-af: Support for NIXLF's UCAST/PROMISC/ALLMULTI modes
  octeontx2-af: Support for setting MAC address
  octeontx2-af: Support for changing RSS algorithm
  octeontx2-af: NIX Rx flowkey configuration for RSS
  octeontx2-af: Install ucast and bcast pkt forwarding rules
  octeontx2-af: Add LMAC channel info to NIXLF_ALLOC response
  octeontx2-af: NPC MCAM and LDATA extract minimal configuration
  octeontx2-af: Enable packet length and csum validation
  octeontx2-af: Support for VTAG strip and capture
  ...
2018-10-24 06:47:44 +01:00
Linus Torvalds 114b5f8f7e This is the bulk of GPIO changes for the v4.20 series:
Core changes:
 
 - A patch series from Hans Verkuil to make it possible to
   enable/disable IRQs on a GPIO line at runtime and drive GPIO
   lines as output without having to put/get them from scratch.
   The irqchip callbacks have been improved so that they can
   use only the fastpatch callbacks to enable/disable irqs
   like any normal irqchip, especially the gpiod_lock_as_irq()
   has been improved to be callable in fastpath context.
   A bunch of rework had to be done to achieve this but it is
   a big win since I never liked to restrict this to slowpath.
   The only call requireing slowpath was try_module_get() and
   this is kept at the .request_resources() slowpath callback.
   In the GPIO CEC driver this is a big win sine a single
   line is used for both outgoing and incoming traffic, and
   this needs to use IRQs for incoming traffic while actively
   driving the line for outgoing traffic.
 
 - Janusz Krzysztofik improved the GPIO array API to pass a
   "cookie" (struct gpio_array) and a bitmap for setting or
   getting multiple GPIO lines at once. This improvement
   orginated in a specific need to speed up an OMAP1 driver and
   has led to a much better API and real performance gains
   when the state of the array can be used to bypass a lot
   of checks and code when we want things to go really fast.
   The previous code would minimize the number of calls
   down to the driver callbacks assuming the CPU speed was
   orders of magnitude faster than the I/O latency, but this
   assumption was wrong on several platforms: what we needed
   to do was to profile and improve the speed on the hot
   path of the array functions and this change is now
   completed.
 
 - Clean out the painful and hard to grasp BNF experiments
   from the device tree bindings. Future approaches are looking
   into using JSON schema for this purpose. (Rob Herring
   is floating a patch series.)
 
 New drivers:
 
 - The RCAR driver now supports r8a774a1 (RZ/G2M).
 
 - Synopsys GPIO via CREGs driver.
 
 Major improvements:
 
 - Modernization of the EP93xx driver to use irqdomain and
   other contemporary concepts.
 
 - The ingenic driver has been merged into the Ingenic pin
   control driver and removed from the GPIO subsystem.
 
 - Debounce support in the ftgpio010 driver.
 -----BEGIN PGP SIGNATURE-----
 
 iQIcBAABAgAGBQJbzdyOAAoJEEEQszewGV1zfYcP/0HBEAOPhHD/i5OQxfKs1msh
 mFT/t/IbTmRpCgbEv4CDx4Kc/InE0sUnQr1TL/1WvU6uObM6Ncxq5Z90MvyrgzYu
 BqQHq2k2tORvkVSNRxcfD/BAAoo1EerXts1kDhutvdKfepfS6DxpENwzvsFgkVlq
 2jj1cdZztjv8A+9cspHDpQP+jDvl1VSc10nR5fRu1TttSpUwzRJaB30NBNXJmMJc
 5KUr67lEbsQRPsBvFErU11bydPqhfT+pXmODcfIwS0EtATQ8WC5mkSb/Ooei0fvT
 oZ7uR3Os8tMf7isOKssEyFabKwhnfOEt6TBt9em0TfUtInOo0Dc7r8TfBcn57fyZ
 xg2R9DQEVRfac8bjhF/BI5KHuN9IMGDDvj6XApumQVliZbISRjMnh3jte6RpcV0A
 Ejqz8FeDY13qvEdOnW1EPpwmXdDVWiEAq0ebGLStKNls+/4gB2HmyxGUOzJf+og5
 hujsxcJzGQqjCe0moeY/1d7vsy0ZjbHoS+p5fy79U212y2O7onEzFU92AX89bxKC
 rx2eCNmiZxCUy1nqu8edO62VnH6QdnqG3o+a4DJfCSHPvFM/E/NX9zHemZubQQ4I
 rYXNy4bL4tEG9cqWMfBxWrpiDZw7H6l8kXwdZG8IMyRU9BcKu96amgZ+jBXwzoaB
 JZelAAUWB9APghJYFr7o
 =YosT
 -----END PGP SIGNATURE-----

Merge tag 'gpio-v4.20-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio

Pull GPIO updates from Linus Walleij:
 "This is the bulk of GPIO changes for the v4.20 series:

  Core changes:

   - A patch series from Hans Verkuil to make it possible to
     enable/disable IRQs on a GPIO line at runtime and drive GPIO lines
     as output without having to put/get them from scratch.

     The irqchip callbacks have been improved so that they can use only
     the fastpatch callbacks to enable/disable irqs like any normal
     irqchip, especially the gpiod_lock_as_irq() has been improved to be
     callable in fastpath context.

     A bunch of rework had to be done to achieve this but it is a big
     win since I never liked to restrict this to slowpath. The only call
     requireing slowpath was try_module_get() and this is kept at the
     .request_resources() slowpath callback. In the GPIO CEC driver this
     is a big win sine a single line is used for both outgoing and
     incoming traffic, and this needs to use IRQs for incoming traffic
     while actively driving the line for outgoing traffic.

   - Janusz Krzysztofik improved the GPIO array API to pass a "cookie"
     (struct gpio_array) and a bitmap for setting or getting multiple
     GPIO lines at once.

     This improvement orginated in a specific need to speed up an OMAP1
     driver and has led to a much better API and real performance gains
     when the state of the array can be used to bypass a lot of checks
     and code when we want things to go really fast.

     The previous code would minimize the number of calls down to the
     driver callbacks assuming the CPU speed was orders of magnitude
     faster than the I/O latency, but this assumption was wrong on
     several platforms: what we needed to do was to profile and improve
     the speed on the hot path of the array functions and this change is
     now completed.

   - Clean out the painful and hard to grasp BNF experiments from the
     device tree bindings. Future approaches are looking into using JSON
     schema for this purpose. (Rob Herring is floating a patch series.)

  New drivers:

   - The RCAR driver now supports r8a774a1 (RZ/G2M).

   - Synopsys GPIO via CREGs driver.

  Major improvements:

   - Modernization of the EP93xx driver to use irqdomain and other
     contemporary concepts.

   - The ingenic driver has been merged into the Ingenic pin control
     driver and removed from the GPIO subsystem.

   - Debounce support in the ftgpio010 driver"

* tag 'gpio-v4.20-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (116 commits)
  gpio: Clarify kerneldoc on gpiochip_set_chained_irqchip()
  gpio: Remove unused 'irqchip' argument to gpiochip_set_cascaded_irqchip()
  gpio: Drop parent irq assignment during cascade setup
  mmc: pwrseq_simple: Fix incorrect handling of GPIO bitmap
  gpio: fix SNPS_CREG kconfig dependency warning
  gpiolib: Initialize gdev field before is used
  gpio: fix kernel-doc after devres.c file rename
  gpio: fix doc string for devm_gpiochip_add_data() to not talk about irq_chip
  gpio: syscon: Fix possible NULL ptr usage
  gpiolib: Show correct direction from the beginning
  pinctrl: msm: Use init_valid_mask exported function
  gpiolib: Add init_valid_mask exported function
  GPIO: add single-register GPIO via CREG driver
  dt-bindings: Document the Synopsys GPIO via CREG bindings
  gpio: mockup: use device properties instead of platform_data
  gpio: Slightly more helpful debugfs
  gpio: omap: Remove set but not used variable 'dev'
  gpio: omap: drop omap_gpio_list
  Accept partial 'gpio-line-names' property.
  gpio: omap: get rid of the conditional PM runtime calls
  ...
2018-10-23 08:45:05 +01:00
Andrew Lunn 92c9d5627a net: phy: phy_support_sym_pause: Clear Asym Pause
When indicating the MAC supports Symmetric Pause, clear the Asymmetric
Pause bit, which could of been already set is the PHY supports it.

Reported-by: Labbe Corentin <clabbe@baylibre.com>
Fixes: c306ad3618 ("net: ethernet: Add helper for MACs which support pause")
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Corentin Labbe <clabbe@baylibre.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2018-10-22 19:38:22 -07:00
Wolfram Sang 2c67e33de2 net: phy: mdio-mux-bcm-iproc: simplify getting .driver_data
We should get 'driver_data' from 'struct device' directly. Going via
platform_device is an unneeded step back and forth.

Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
2018-10-21 21:10:12 -07:00
Yuiko Oshino bff5b4b373 net: phy: micrel: add Microchip KSZ9131 initial driver
Add support for Microchip Technology KSZ9131 10/100/1000 Ethernet PHY

Signed-off-by: Yuiko Oshino <yuiko.oshino@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2018-10-19 17:02:23 -07:00
Gustavo A. R. Silva 47d20212aa net: phy: mscc: fix memory leak in vsc8574_config_pre_init
In case memory resources for *fw* were successfully allocated,
release them before return.

Addresses-Coverity-ID: 1473968 ("Resource leak")
Fixes: 00d70d8e0e ("net: phy: mscc: add support for VSC8574 PHY")
Reviewed-by: Quentin Schulz <quentin.schulz@bootlin.com>
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2018-10-17 22:08:55 -07:00
Gustavo A. R. Silva e519869af3 net: phy: mscc: fix signedness bug in vsc85xx_downshift_get
Currently, the error handling for the call to function
phy_read_paged() doesn't work because *reg_val* is of
type u16 (16 bits, unsigned), which makes it impossible
for it to hold a value less than 0.

Fix this by changing the type of variable *reg_val* to int.

Addresses-Coverity-ID: 1473970 ("Unsigned compared against 0")
Fixes: 6a0bfbbe20 ("net: phy: mscc: migrate to phy_select/restore_page functions")
Reviewed-by: Quentin Schulz <quentin.schulz@bootlin.com>
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2018-10-17 22:08:55 -07:00
Heiner Kallweit c45d715065 net: phy: merge phy_start_aneg and phy_start_aneg_priv
After commit 9f2959b6b5 ("net: phy: improve handling delayed work")
the sync parameter isn't needed any longer in phy_start_aneg_priv().
This allows to merge phy_start_aneg() and phy_start_aneg_priv().

Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2018-10-15 23:13:07 -07:00
Heiner Kallweit eb4c470a15 net: phy: simplify handling of PHY_RESUMING in state machine
Simplify code for handling state PHY_RESUMING, no functional change
intended.

Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2018-10-15 22:06:38 -07:00
Heiner Kallweit 74fb5e25a3 net: phy: improve handling of PHY_RUNNING in state machine
Handling of state PHY_RUNNING seems to be more complex than it needs
to be. If not polling, then we don't have to do anything, we'll
receive an interrupt and go to state PHY_CHANGELINK once the link
goes down. If polling and link is down, we don't have to go the
extra mile over PHY_CHANGELINK and call phy_read_status() again
but can set status PHY_NOLINK directly.

Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2018-10-15 22:06:38 -07:00
Heiner Kallweit 6384e48323 net: phy: trigger state machine immediately in phy_start_machine
When starting the state machine there may be work to be done
immediately, e.g. if the initial state is PHY_UP then the state
machine may trigger an autonegotiation. Having said that I see no need
to wait a second until the state machine is run first time.

Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2018-10-15 22:00:06 -07:00
David S. Miller d864991b22 Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net
Conflicts were easy to resolve using immediate context mostly,
except the cls_u32.c one where I simply too the entire HEAD
chunk.

Signed-off-by: David S. Miller <davem@davemloft.net>
2018-10-12 21:38:46 -07:00
Sebastian Andrzej Siewior 052858663d net: phy: sfp: remove sfp_mutex's definition
The sfp_mutex variable is defined but never used in this file. Not even
in the commit that introduced that variable.

Remove sfp_mutex, it has no purpose.

Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
2018-10-11 12:10:06 -07:00
Quentin Schulz 00d70d8e0e net: phy: mscc: add support for VSC8574 PHY
The VSC8574 PHY is a 4-ports PHY that is 10/100/1000BASE-T, 100BASE-FX,
1000BASE-X and triple-speed copper SFP capable, can communicate with
the MAC via SGMII, QSGMII or 1000BASE-X, supports WOL, downshifting and
can set the blinking pattern of each of its 4 LEDs, supports SyncE as
well as HP Auto-MDIX detection.

This adds support for 10/100/1000BASE-T, SGMII/QSGMII link with the MAC,
WOL, downshifting, HP Auto-MDIX detection and blinking pattern for its 4
LEDs.

The VSC8574 has also an internal Intel 8051 microcontroller whose
firmware needs to be patched when the PHY is reset. If the 8051's
firmware has the expected CRC, its patching can be skipped. The
microcontroller can be accessed from any port of the PHY, though the CRC
function can only be done through the PHY that is the base PHY of the
package (internal address 0) due to a limitation of the firmware.

The GPIO register bank is a set of registers that are common to all PHYs
in the package. So any modification in any register of this bank affects
all PHYs of the package.

If the PHYs haven't been reset before booting the Linux kernel and were
configured to use interrupts for e.g. link status updates, it is
required to clear the interrupts mask register of all PHYs before being
able to use interrupts with any PHY. The first PHY of the package that
will be init will take care of clearing all PHYs interrupts mask
registers. Thus, we need to keep track of the init sequence in the
package, if it's already been done or if it's to be done.

Most of the init sequence of a PHY of the package is common to all PHYs
in the package, thus we use the SMI broadcast feature which enables us
to propagate a write in one register of one PHY to all PHYs in the same
package.

Signed-off-by: Quentin Schulz <quentin.schulz@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2018-10-08 10:31:28 -07:00
Quentin Schulz a5afc16780 net: phy: mscc: add support for VSC8584 PHY
The VSC8584 PHY is a 4-ports PHY that is 10/100/1000BASE-T, 100BASE-FX,
1000BASE-X and triple-speed copper SFP capable, can communicate with the
MAC via SGMII, QSGMII or 1000BASE-X, supports downshifting and can set
the blinking pattern of each of its 4 LEDs, supports hardware offloading
of MACsec and supports SyncE as well as HP Auto-MDIX detection.

This adds support for 10/100/1000BASE-T, SGMII/QSGMII link with the MAC,
downshifting, HP Auto-MDIX detection and blinking pattern for its 4
LEDs.

The VSC8584 has also an internal Intel 8051 microcontroller whose
firmware needs to be patched when the PHY is reset. If the 8051's
firmware has the expected CRC, its patching can be skipped. The
microcontroller can be accessed from any port of the PHY, though the CRC
function can only be done through the PHY that is the base PHY of the
package (internal address 0) due to a limitation of the firmware.

The GPIO register bank is a set of registers that are common to all PHYs
in the package. So any modification in any register of this bank affects
all PHYs of the package.

If the PHYs haven't been reset before booting the Linux kernel and were
configured to use interrupts for e.g. link status updates, it is
required to clear the interrupts mask register of all PHYs before being
able to use interrupts with any PHY. The first PHY of the package that
will be init will take care of clearing all PHYs interrupts mask
registers. Thus, we need to keep track of the init sequence in the
package, if it's already been done or if it's to be done.

Most of the init sequence of a PHY of the package is common to all PHYs
in the package, thus we use the SMI broadcast feature which enables us
to propagate a write in one register of one PHY to all PHYs in the same
package.

The revA of the VSC8584 PHY (which is not and will not be publicly
released) should NOT patch the firmware of the microcontroller or it'll
make things worse, the easiest way is just to not support it.

Signed-off-by: Quentin Schulz <quentin.schulz@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2018-10-08 10:31:28 -07:00
Quentin Schulz 629ea0f140 net: phy: mscc: remove unneeded temporary variable
Here, the rc variable is either used only for the condition right after
the assignment or right before being used as the return value of the
function it's being used in.

So let's remove this unneeded temporary variable whenever possible.

Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Quentin Schulz <quentin.schulz@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2018-10-08 10:29:21 -07:00
Quentin Schulz 6f0430c78c net: phy: mscc: shorten `x != 0` condition to `x`
`if (x != 0)` is basically a more verbose version of `if (x)` so let's
use the latter so it's consistent throughout the whole driver.

Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Quentin Schulz <quentin.schulz@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2018-10-08 10:29:21 -07:00
Quentin Schulz b7d373c500 net: phy: mscc: remove unneeded parenthesis
The == operator precedes the || operator, so we can remove the
parenthesis around (a == b) || (c == d).

The condition is rather explicit and short so removing the parenthesis
definitely does not make it harder to read.

Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Quentin Schulz <quentin.schulz@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2018-10-08 10:29:21 -07:00
Raju Lakkaraju 96dae01f27 net: phy: mscc: Add EEE init sequence
Microsemi PHYs (VSC 8530/31/40/41) need to update the Energy Efficient
Ethernet initialization sequence.
In order to avoid certain link state errors that could result in link
drops and packet loss, the physical coding sublayer (PCS) must be
updated with settings related to EEE in order to improve performance.

Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Raju Lakkaraju <Raju.Lakkaraju@microchip.com>
Signed-off-by: Quentin Schulz <quentin.schulz@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2018-10-08 10:29:21 -07:00
Raju Lakkaraju f76178dc52 net: phy: mscc: add ethtool statistics counters
There are a few counters available in the PHY: receive errors, false
carriers, link disconnects, media CRC errors and valids counters.

So let's expose those in the PHY driver.

Use the priv structure as the next PHY to be supported has a few
additional counters.

Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Raju Lakkaraju <Raju.Lakkaraju@microsemi.com>
Signed-off-by: Quentin Schulz <quentin.schulz@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2018-10-08 10:29:21 -07:00
Quentin Schulz 6a0bfbbe20 net: phy: mscc: migrate to phy_select/restore_page functions
The Microsemi PHYs have multiple banks of registers (called pages).
Registers can only be accessed from one page, if we need a register from
another page, we need to switch the page and the registers of all other
pages are not accessible anymore.

Basically, to read register 5 from page 0, 1, 2, etc., you do the same
phy_read(phydev, 5); but you need to set the desired page beforehand.

In order to guarantee that two concurrent functions do not change the
page, we need to do some locking per page. This can be achieved with the
use of phy_select_page and phy_restore_page functions but phy_write/read
calls in-between those two functions shall be replaced by their
lock-free alternative __phy_write/read.

Let's migrate this driver to those functions.

Suggested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Quentin Schulz <quentin.schulz@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2018-10-08 10:29:20 -07:00
David S. Miller 72438f8cef Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net 2018-10-06 14:43:42 -07:00
Baruch Siach 7e41837527 net: phy: phylink: fix SFP interface autodetection
When connecting SFP PHY to phylink use the detected interface.
Otherwise, the link fails to come up when the configured 'phy-mode'
differs from the SFP detected mode.

Move most of phylink_connect_phy() into __phylink_connect_phy(), and
leave phylink_connect_phy() as a wrapper. phylink_sfp_connect_phy() can
now pass the SFP detected PHY interface to __phylink_connect_phy().

This fixes 1GB SFP module link up on eth3 of the Macchiatobin board that
is configured in the DT to "2500base-x" phy-mode.

Fixes: 9525ae8395 ("phylink: add phylink infrastructure")
Suggested-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
2018-10-05 01:04:12 -07:00
David S. Miller 6f41617bf2 Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net
Minor conflict in net/core/rtnetlink.c, David Ahern's bug fix in 'net'
overlapped the renaming of a netlink attribute in net-next.

Signed-off-by: David S. Miller <davem@davemloft.net>
2018-10-03 21:00:17 -07:00
Rob Herring 024926def6 net: phy: Convert to using %pOFn instead of device_node.name
In preparation to remove the node name pointer from struct device_node,
convert printf users to use the %pOFn format specifier.

Cc: Andrew Lunn <andrew@lunn.ch>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: netdev@vger.kernel.org
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2018-10-01 23:29:37 -07:00
Heiner Kallweit 9f2959b6b5 net: phy: improve handling delayed work
Using mod_delayed_work() allows to simplify handling delayed work and
removes the need for the sync parameter in phy_trigger_machine().
Also introduce a helper phy_queue_state_machine() to encapsulate the
low-level delayed work calls. No functional change intended.

Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2018-10-01 23:14:10 -07:00
Andrew Lunn 719655a149 net: phy: Replace phy driver features u32 with link_mode bitmap
This is one step in allowing phylib to make use of link_mode bitmaps,
instead of u32 for supported and advertised features. Convert the phy
drivers to use bitmaps to indicates the features they support.

Build bitmap equivalents of the u32 values at runtime, and have the
drivers point to the appropriate bitmap. These bitmaps are shared, and
we don't want a driver to modify them. So mark them __ro_after_init.

Within phylib, the features bitmap is currently turned back into a
u32. This will be removed once the whole of phylib, and the drivers
are converted to use bitmaps.

Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
2018-10-01 22:55:36 -07:00
Andrew Lunn c4fabb8b3c net: phy: Add phydev_info()
Add phydev_info() and make use of it within the phy drivers and core
code.

Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
2018-10-01 22:55:36 -07:00
Andrew Lunn ab2a605fa6 net: phy: Add phydev_warn()
Not all new style LINK_MODE bits can be converted into old style
SUPPORTED bits. We need to warn when such a conversion is attempted.
Add a helper for this.

Convert all pr_warn() calls to phydev_warn() where possible.

Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2018-10-01 22:55:35 -07:00
Andrew Lunn b31cdffa23 net: phy: Move linkmode helpers to somewhere public
phylink has some useful helpers to working with linkmode bitmaps.
Move them to there own header so other code can use them.

Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2018-10-01 22:55:35 -07:00
Arnd Bergmann 9b97123a58 net: phy: mdio-bcm-unimac: mark PM functions as __maybe_unused
The newly added runtime-pm support causes a harmless warning
when CONFIG_PM is disabled:

drivers/net/phy/mdio-bcm-unimac.c:330:12: error: 'unimac_mdio_resume' defined but not used [-Werror=unused-function]
 static int unimac_mdio_resume(struct device *d)
drivers/net/phy/mdio-bcm-unimac.c:321:12: error: 'unimac_mdio_suspend' defined but not used [-Werror=unused-function]
 static int unimac_mdio_suspend(struct device *d)

Marking the functions as __maybe_unused is the easiest workaround
and avoids adding #ifdef checks.

Fixes: b78ac6ecd1 ("net: phy: mdio-bcm-unimac: Allow configuring MDIO clock divider")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
2018-09-28 10:25:11 -07:00
Arnd Bergmann 31bae7dad3 phy: mscc: fix printf format
gcc points out that the length of the temporary buffer may not be sufficient for
large numbers of leds:

drivers/net/phy/mscc.c: In function 'vsc85xx_probe':
drivers/net/phy/mscc.c:460:45: error: '-mode' directive writing 5 bytes into a region of size between 0 and 9 [-Werror=format-overflow=]
   ret = sprintf(led_dt_prop, "vsc8531,led-%d-mode", i);
                                             ^~~~~
drivers/net/phy/mscc.c:460:9: note: 'sprintf' output between 19 and 28 bytes into a destination of size 22
   ret = sprintf(led_dt_prop, "vsc8531,led-%d-mode", i);
         ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

While we can make a reasonable assumption that the number of LEDs is small,
the cost of making the buffer a little bigger is insignificant as well.

Fixes: 11bfdabb7f ("net: phy: mscc: factorize code for LEDs mode")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2018-09-28 10:25:11 -07:00
Andrew Lunn 3e32247448 net: phy: sfp: Fix unregistering of HWMON SFP device
A HWMON device is only registered is the SFP module supports the
diagnostic page and is complient to SFF8472. Don't unconditionally
unregister the hwmon device when the SFP module is remove, otherwise
we access data structures which don't exist.

Reported-by: Florian Fainelli <f.fainelli@gmail.com>
Fixes: 1323061a01 ("net: phy: sfp: Add HWMON support for module sensors")
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2018-09-26 20:23:31 -07:00
Heiner Kallweit 93f41e67dc net: phy: fix WoL handling when suspending the PHY
Core of the problem is that phy_suspend() suspends the PHY when it
should not because of WoL. phy_suspend() checks for WoL already, but
this works only if the PHY driver handles WoL (what is rarely the case).
Typically WoL is handled by the MAC driver.

This patch uses new member wol_enabled of struct net_device as
additional criteria in the check when not to suspend the PHY because
of WoL.

Last but not least change phy_detach() to call phy_suspend() before
attached_dev is set to NULL. phy_suspend() accesses attached_dev
when checking whether the MAC driver activated WoL.

Fixes: f1e911d5d0 ("r8169: add basic phylib support")
Fixes: e8cfd9d6c7 ("net: phy: call state machine synchronously in phy_stop")
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2018-09-26 20:04:11 -07:00
David S. Miller d31d1d03aa Revert "net: phy: fix WoL handling when suspending the PHY"
This reverts commit e0511f6c1c.

I commited the wrong version of these changes.

Signed-off-by: David S. Miller <davem@davemloft.net>
2018-09-26 20:01:36 -07:00
Heiner Kallweit e0511f6c1c net: phy: fix WoL handling when suspending the PHY
Actually there's nothing wrong with the two changes marked as "Fixes",
they just revealed a problem which has been existing before.
After having switched r8169 to phylib it was reported that WoL from
shutdown doesn't work any longer (WoL from suspend isn't affected).
Reason is that during shutdown phy_disconnect()->phy_detach()->
phy_suspend() is called.
A similar issue occurs when the phylib state machine calls
phy_suspend() when handling state PHY_HALTED.

Core of the problem is that phy_suspend() suspends the PHY when it
should not due to WoL. phy_suspend() checks for WoL already, but this
works only if the PHY driver handles WoL (what is rarely the case).
Typically WoL is handled by the MAC driver.

phylib knows about this and handles it in mdio_bus_phy_may_suspend(),
but that's used only when suspending the system, not in other cases
like shutdown.

Therefore factor out the relevant check from
mdio_bus_phy_may_suspend() to a new function phy_may_suspend() and
use it in phy_suspend().

Last but not least change phy_detach() to call phy_suspend() before
attached_dev is set to NULL. phy_suspend() accesses attached_dev
when checking whether the MAC driver activated WoL.

Fixes: f1e911d5d0 ("r8169: add basic phylib support")
Fixes: e8cfd9d6c7 ("net: phy: call state machine synchronously in phy_stop")
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2018-09-26 20:00:16 -07:00
David S. Miller 4b1bd69769 net: phy: marvell: Fix build.
Local variable 'autoneg' doesn't even exist:

drivers/net/phy/marvell.c: In function 'm88e1121_config_aneg':
drivers/net/phy/marvell.c:468:25: error: 'autoneg' undeclared (first use in this function); did you mean 'put_net'?
  if (phydev->autoneg != autoneg || changed) {
                         ^~~~~~~

Fixes: d6ab933647 ("net: phy: marvell: Avoid unnecessary soft reset")
Reported-by:Vakul Garg <vakul.garg@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2018-09-25 22:41:31 -07:00
Florian Fainelli d6ab933647 net: phy: marvell: Avoid unnecessary soft reset
The BMCR.RESET bit on the Marvell PHYs has a special meaning in that
it commits the register writes into the HW for it to latch and be
configured appropriately. Doing software resets causes link drops, and
this is unnecessary disruption if nothing changed.

Determine from marvell_set_polarity()'s return code whether the register value
was changed and if it was, propagate that to the logic that hits the software
reset bit.

This avoids doing unnecessary soft reset if the PHY is configured in
the same state it was previously, this also eliminates the need for a
m88e1111_config_aneg() function since it now is the same as
marvell_config_aneg().

Tested-by: Wang, Dongsheng <dongsheng.wang@hxt-semitech.com>
Tested-by: Chris Healy <cphealy@gmail.com>
Tested-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Clemens Gruber <clemens.gruber@pqgruber.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2018-09-25 20:26:45 -07:00
Florian Fainelli 6e2d85ec05 net: phy: Stop with excessive soft reset
While consolidating the PHY reset in phy_init_hw() an unconditionaly
BMCR soft-reset I became quite trigger happy with those. This was later
on deactivated for the Generic PHY driver on the premise that a prior
software entity (e.g: bootloader) might have applied workarounds in
commit 0878fff1f4 ("net: phy: Do not perform software reset for
Generic PHY").

Since we have a hook to wire-up a soft_reset callback, just use that and
get rid of the call to genphy_soft_reset() entirely. This speeds up
initialization and link establishment for most PHYs out there that do
not require a reset.

Fixes: 87aa9f9c61 ("net: phy: consolidate PHY reset in phy_init_hw()")
Tested-by: Wang, Dongsheng <dongsheng.wang@hxt-semitech.com>
Tested-by: Chris Healy <cphealy@gmail.com>
Tested-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Clemens Gruber <clemens.gruber@pqgruber.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2018-09-25 20:26:45 -07:00
David S. Miller a06ee256e5 Merge ra.kernel.org:/pub/scm/linux/kernel/git/davem/net
Version bump conflict in batman-adv, take what's in net-next.

iavf conflict, adjustment of netdev_ops in net-next conflicting
with poll controller method removal in net.

Signed-off-by: David S. Miller <davem@davemloft.net>
2018-09-25 10:35:29 -07:00
Florian Fainelli b78ac6ecd1 net: phy: mdio-bcm-unimac: Allow configuring MDIO clock divider
Allow the configuration of the MDIO clock divider when the Device Tree
contains 'clock-frequency' property (similar to I2C and SPI buses).
Because the hardware may have lost its state during suspend/resume,
re-apply the MDIO clock divider upon resumption.

Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2018-09-21 19:08:24 -07:00
Heiner Kallweit 075ddebc32 net: phy: don't reschedule state machine when PHY is halted
When being in state PHY_HALTED we don't have to reschedule the
state machine, phy_start() will start it again.

Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2018-09-21 18:59:29 -07:00
Antoine Tenart aeeb2e8fde net: phy: phylink: ensure the carrier is off when starting phylink
Phylink made an assumption about the carrier state being down when
calling phylink_start(). If this assumption isn't satisfied, the
internal phylink state could misbehave and a net device could end up not
being functional.

This patch fixes this by explicitly calling netif_carrier_off() in
phylink_start().

Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Acked-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
2018-09-19 21:15:01 -07:00