Use the macro 'swap()' defined in 'include/linux/minmax.h' to avoid
opencoding it.
Reported-by: Zeal Robot <zealci@zte.com.cn>
Signed-off-by: Yang Guang <yang.guang5@zte.com.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use pci_info instead to avoid unnamed/uninitialized noise:
[197088.688729] sfc 0000:01:00.0: Solarflare NIC detected
[197088.690333] sfc 0000:01:00.0: Part Number : SFN5122F
[197088.729061] sfc 0000:01:00.0 (unnamed net_device) (uninitialized): no SR-IOV VFs probed
[197088.729071] sfc 0000:01:00.0 (unnamed net_device) (uninitialized): no PTP support
Inspired by fa44821a4d ("sfc: don't use netif_info et al before
net_device is registered") from Heiner Kallweit.
Signed-off-by: Erik Ekman <erik@kryo.se>
Acked-by: Martin Habets <habetsm.xilinx@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 1/10GbaseT modes were set up for cards with SFP+ cages in
3497ed8c85 ("sfc: report supported link speeds on SFP connections").
10GbaseT was likely used since no 10G fibre mode existed.
The missing fibre modes for 1/10G were added to ethtool.h in 5711a98221
("net: ethtool: add support for 1000BaseX and missing 10G link modes")
shortly thereafter.
The user guide available at https://support-nic.xilinx.com/wp/drivers
lists support for the following cable and transceiver types in section 2.9:
- QSFP28 100G Direct Attach Cables
- QSFP28 100G SR Optical Transceivers (with SR4 modules listed)
- SFP28 25G Direct Attach Cables
- SFP28 25G SR Optical Transceivers
- QSFP+ 40G Direct Attach Cables
- QSFP+ 40G Active Optical Cables
- QSFP+ 40G SR4 Optical Transceivers
- QSFP+ to SFP+ Breakout Direct Attach Cables
- QSFP+ to SFP+ Breakout Active Optical Cables
- SFP+ 10G Direct Attach Cables
- SFP+ 10G SR Optical Transceivers
- SFP+ 10G LR Optical Transceivers
- SFP 1000BASE‐T Transceivers
- 1G Optical Transceivers
(From user guide issue 28. Issue 16 which also includes older cards like
SFN5xxx/SFN6xxx has matching lists for 1/10/40G transceiver types.)
Regarding SFP+ 10GBASE‐T transceivers the latest guide says:
"Solarflare adapters do not support 10GBASE‐T transceiver modules."
Tested using SFN5122F-R7 (with 2 SFP+ ports). Supported link modes do not change
depending on module used (tested with 1000BASE-T, 1000BASE-BX10, 10GBASE-LR).
Before:
$ ethtool ext
Settings for ext:
Supported ports: [ FIBRE ]
Supported link modes: 1000baseT/Full
10000baseT/Full
Supported pause frame use: Symmetric Receive-only
Supports auto-negotiation: No
Supported FEC modes: Not reported
Advertised link modes: Not reported
Advertised pause frame use: No
Advertised auto-negotiation: No
Advertised FEC modes: Not reported
Link partner advertised link modes: Not reported
Link partner advertised pause frame use: No
Link partner advertised auto-negotiation: No
Link partner advertised FEC modes: Not reported
Speed: 1000Mb/s
Duplex: Full
Auto-negotiation: off
Port: FIBRE
PHYAD: 255
Transceiver: internal
Current message level: 0x000020f7 (8439)
drv probe link ifdown ifup rx_err tx_err hw
Link detected: yes
After:
$ ethtool ext
Settings for ext:
Supported ports: [ FIBRE ]
Supported link modes: 1000baseT/Full
1000baseX/Full
10000baseCR/Full
10000baseSR/Full
10000baseLR/Full
Supported pause frame use: Symmetric Receive-only
Supports auto-negotiation: No
Supported FEC modes: Not reported
Advertised link modes: Not reported
Advertised pause frame use: No
Advertised auto-negotiation: No
Advertised FEC modes: Not reported
Link partner advertised link modes: Not reported
Link partner advertised pause frame use: No
Link partner advertised auto-negotiation: No
Link partner advertised FEC modes: Not reported
Speed: 1000Mb/s
Duplex: Full
Auto-negotiation: off
Port: FIBRE
PHYAD: 255
Transceiver: internal
Supports Wake-on: g
Wake-on: d
Current message level: 0x000020f7 (8439)
drv probe link ifdown ifup rx_err tx_err hw
Link detected: yes
Signed-off-by: Erik Ekman <erik@kryo.se>
Acked-by: Martin Habets <habetsm.xilinx@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Everything except the first 32 bits was lost when the pause flags were
added. This makes the 50000baseCR2 mode flag (bit 34) not appear.
I have tested this with a 10G card (SFN5122F-R7) by modifying it to
return a non-legacy link mode (10000baseCR).
Signed-off-by: Erik Ekman <erik@kryo.se>
Signed-off-by: David S. Miller <davem@davemloft.net>
This big patch sprinkles const on local variables and
function arguments which may refer to netdev->dev_addr.
Commit 406f42fa0d ("net-next: When a bond have a massive amount
of VLANs...") introduced a rbtree for faster Ethernet address look
up. To maintain netdev->dev_addr in this tree we need to make all
the writes to it got through appropriate helpers.
Some of the changes here are not strictly required - const
is sometimes cast off but pointer is not used for writing.
It seems like it's still better to add the const in case
the code changes later or relevant -W flags get enabled
for the build.
No functional changes.
Link: https://lore.kernel.org/r/20211014142432.449314-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Convert Ethernet from ether_addr_copy() to eth_hw_addr_set():
@@
expression dev, np;
@@
- ether_addr_copy(dev->dev_addr, np)
+ eth_hw_addr_set(dev, np)
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert all Ethernet drivers from memcpy(... ETH_ADDR)
to eth_hw_addr_set():
@@
expression dev, np;
@@
- memcpy(dev->dev_addr, np, ETH_ALEN)
+ eth_hw_addr_set(dev, np)
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Previous patch addressed the situation of having some free resources for
xdp tx but not enough for one tx queue per CPU. This patch address the
worst case of not having resources at all for xdp tx.
Instead of using queues dedicated to xdp, normal queues used by network
stack are shared for both cases, using __netif_tx_lock for
synchronization. Also queue stop/restart must be considered in the xdp
path to avoid freezing the queue.
This is not the ideal situation we might want to be, and a performance
penalty is expected both for normal and xdp traffic, but at least XDP
will work in all possible situations (with a warning in the logs),
improving a bit the pain of not knowing in what situations we can use it
and in what situations we cannot.
Signed-off-by: Íñigo Huguet <ihuguet@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If there are not enough resources to allocate one TX queue per core for
XDP TX it was completely disabled.
This patch implements a fallback solution for sharing the available
queues using __netif_tx_lock for synchronization. In the normal case that
there is one TX queue per CPU, no locking is done, as it was before.
With this fallback solution, XDP TX will work in much more cases that
were failing, specially in machines with many CPUs. It's hard for XDP
users to know what features are supported across different NICs and
configurations, so they will benefit on having wider support.
Signed-off-by: Íñigo Huguet <ihuguet@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use pci_vpd_find_ro_info_keyword() to search for keywords in VPD to
simplify the code.
Replace netif_err() with pci_err() because the netdevice isn't registered
yet, which results in very ugly messages.
Use kmemdup_nul() instead of open-coding it.
This is the same as 37838aa437 ("sfc: Search VPD with
pci_vpd_find_ro_info_keyword()"), just for the falcon chip version.
Link: https://lore.kernel.org/r/898282a1-13bd-17bc-2e9a-d3dcd336b46c@gmail.com
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Use pci_vpd_alloc() to dynamically allocate a properly sized buffer and
read the full VPD data into it.
This avoids having to allocate a buffer on the stack, and we don't have to
make any assumptions on VPD size and location of information in VPD.
This is the same as 5119e20fac ("sfc: Read VPD with pci_vpd_alloc()"),
just for the falcon chip version.
Link: https://lore.kernel.org/r/2a8d069e-9516-50d8-6520-2614222c8f5f@gmail.com
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
In order to support more coalesce parameters through netlink,
add two new parameter kernel_coal and extack for .set_coalesce
and .get_coalesce, then some extra info can return to user with
the netlink API.
Signed-off-by: Yufeng Mo <moyufeng@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This is the same as 37838aa437 "sfc: Search VPD with
pci_vpd_find_ro_info_keyword()", just for the falcon chip version.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is the same as 5119e20fac "sfc: Read VPD with pci_vpd_alloc()",
just for the falcon chip version.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use pci_vpd_find_ro_info_keyword() to search for keywords in VPD to
simplify the code.
Replace netif_err() with pci_err() because the netdevice isn't registered
yet, which results in very ugly messages.
Use kmemdup_nul() instead of open-coding it.
Link: https://lore.kernel.org/r/bf5d4ba9-61a9-2bfe-19ec-75472732d74d@gmail.com
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Use pci_vpd_alloc() to dynamically allocate a properly sized buffer and
read the full VPD data into it.
This avoids having to allocate a buffer on the stack, and we don't have to
make any assumptions on VPD size and location of information in VPD.
Link: https://lore.kernel.org/r/e58f1e40-c043-0266-9a0f-e5a7f3f6883c@gmail.com
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The 'imply' keyword does not do what most people think it does, it only
politely asks Kconfig to turn on another symbol, but does not prevent
it from being disabled manually or built as a loadable module when the
user is built-in. In the ICE driver, the latter now causes a link failure:
aarch64-linux-ld: drivers/net/ethernet/intel/ice/ice_main.o: in function `ice_eth_ioctl':
ice_main.c:(.text+0x13b0): undefined reference to `ice_ptp_get_ts_config'
ice_main.c:(.text+0x13b0): relocation truncated to fit: R_AARCH64_CALL26 against undefined symbol `ice_ptp_get_ts_config'
aarch64-linux-ld: ice_main.c:(.text+0x13bc): undefined reference to `ice_ptp_set_ts_config'
ice_main.c:(.text+0x13bc): relocation truncated to fit: R_AARCH64_CALL26 against undefined symbol `ice_ptp_set_ts_config'
aarch64-linux-ld: drivers/net/ethernet/intel/ice/ice_main.o: in function `ice_prepare_for_reset':
ice_main.c:(.text+0x31fc): undefined reference to `ice_ptp_release'
ice_main.c:(.text+0x31fc): relocation truncated to fit: R_AARCH64_CALL26 against undefined symbol `ice_ptp_release'
aarch64-linux-ld: drivers/net/ethernet/intel/ice/ice_main.o: in function `ice_rebuild':
This is a recurring problem in many drivers, and we have discussed
it several times befores, without reaching a consensus. I'm providing
a link to the previous email thread for reference, which discusses
some related problems.
To solve the dependency issue better than the 'imply' keyword, introduce a
separate Kconfig symbol "CONFIG_PTP_1588_CLOCK_OPTIONAL" that any driver
can depend on if it is able to use PTP support when available, but works
fine without it. Whenever CONFIG_PTP_1588_CLOCK=m, those drivers are
then prevented from being built-in, the same way as with a 'depends on
PTP_1588_CLOCK || !PTP_1588_CLOCK' dependency that does the same trick,
but that can be rather confusing when you first see it.
Since this should cover the dependencies correctly, the IS_REACHABLE()
hack in the header is no longer needed now, and can be turned back
into a normal IS_ENABLED() check. Any driver that gets the dependency
wrong will now cause a link time failure rather than being unable to use
PTP support when that is in a loadable module.
However, the two recently added ptp_get_vclocks_index() and
ptp_convert_timestamp() interfaces are only called from builtin code with
ethtool and socket timestamps, so keep the current behavior by stubbing
those out completely when PTP is in a loadable module. This should be
addressed properly in a follow-up.
As Richard suggested, we may want to actually turn PTP support into a
'bool' option later on, preventing it from being a loadable module
altogether, which would be one way to solve the problem with the ethtool
interface.
Fixes: 06c16d89d2 ("ice: register 1588 PTP clock device object for E810 devices")
Link: https://lore.kernel.org/netdev/20210804121318.337276-1-arnd@kernel.org/
Link: https://lore.kernel.org/netdev/CAK8P3a06enZOf=XyZ+zcAwBczv41UuCTz+=0FMf2gBz1_cOnZQ@mail.gmail.com/
Link: https://lore.kernel.org/netdev/CAK8P3a3=eOxE-K25754+fB_-i_0BZzf9a9RfPTX3ppSwu9WZXw@mail.gmail.com/
Link: https://lore.kernel.org/netdev/20210726084540.3282344-1-arnd@kernel.org/
Acked-by: Shannon Nelson <snelson@pensando.io>
Acked-by: Jacob Keller <jacob.e.keller@intel.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20210812183509.1362782-1-arnd@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Most users of ndo_do_ioctl are ethernet drivers that implement
the MII commands SIOCGMIIPHY/SIOCGMIIREG/SIOCSMIIREG, or hardware
timestamping with SIOCSHWTSTAMP/SIOCGHWTSTAMP.
Separate these from the few drivers that use ndo_do_ioctl to
implement SIOCBOND, SIOCBR and SIOCWANDEV commands.
This is a purely cosmetic change intended to help readers find
their way through the implementation.
Cc: Doug Ledford <dledford@redhat.com>
Cc: Jason Gunthorpe <jgg@ziepe.ca>
Cc: Jay Vosburgh <j.vosburgh@gmail.com>
Cc: Veaceslav Falico <vfalico@gmail.com>
Cc: Andy Gospodarek <andy@greyhouse.net>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Vivien Didelot <vivien.didelot@gmail.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Vladimir Oltean <olteanv@gmail.com>
Cc: Leon Romanovsky <leon@kernel.org>
Cc: linux-rdma@vger.kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Jason Gunthorpe <jgg@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If it's not possible to allocate enough channels for XDP, XDP_TX and
XDP_REDIRECT don't work. However, only a message saying that not enough
channels were available was shown, but not saying what are the
consequences in that case. The user didn't know if he/she can use XDP
or not, if the performance is reduced, or what.
Signed-off-by: Íñigo Huguet <ihuguet@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 99ba0ea616 ("sfc: adjust efx->xdp_tx_queue_count with the real
number of initialized queues") intended to fix a problem caused by a
round up when calculating the number of XDP channels and queues.
However, this was not the real problem. The real problem was that the
number of XDP TX queues had been reduced to half in
commit e26ca4b535 ("sfc: reduce the number of requested xdp ev queues"),
but the variable xdp_tx_queue_count had remained the same.
Once the correct number of XDP TX queues is created again in the
previous patch of this series, this also can be reverted since the error
doesn't actually exist.
Only in the case that there is a bug in the code we can have different
values in xdp_queue_number and efx->xdp_tx_queue_count. Because of this,
and per Edward Cree's suggestion, I add instead a WARN_ON to catch if it
happens again in the future.
Note that the number of allocated queues can be higher than the number
of used ones due to the round up, as explained in the existing comment
in the code. That's why we also have to stop increasing xdp_queue_number
beyond efx->xdp_tx_queue_count.
Signed-off-by: Íñigo Huguet <ihuguet@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes: e26ca4b535 sfc: reduce the number of requested xdp ev queues
The buggy commit intended to allocate less channels for XDP in order to
be more unlikely to reach the limit of 32 channels of the driver.
The idea was to use each IRQ/eventqeue for more XDP TX queues than
before, calculating which is the maximum number of TX queues that one
event queue can handle. For example, in EF10 each event queue could
handle up to 8 queues, better than the 4 they were handling before the
change. This way, it would have to allocate half of channels than before
for XDP TX.
The problem is that the TX queues are also contained inside the channel
structs, and there are only 4 queues per channel. Reducing the number of
channels means also reducing the number of queues, resulting in not
having the desired number of 1 queue per CPU.
This leads to getting errors on XDP_TX and XDP_REDIRECT if they're
executed from a high numbered CPU, because there only exist queues for
the low half of CPUs, actually. If XDP_TX/REDIRECT is executed in a low
numbered CPU, the error doesn't happen. This is the error in the logs
(repeated many times, even rate limited):
sfc 0000:5e:00.0 ens3f0np0: XDP TX failed (-22)
This errors happens in function efx_xdp_tx_buffers, where it expects to
have a dedicated XDP TX queue per CPU.
Reverting the change makes again more likely to reach the limit of 32
channels in machines with many CPUs. If this happen, no XDP_TX/REDIRECT
will be possible at all, and we will have this log error messages:
At interface probe:
sfc 0000:5e:00.0: Insufficient resources for 12 XDP event queues (24 other channels, max 32)
At every subsequent XDP_TX/REDIRECT failure, rate limited:
sfc 0000:5e:00.0 ens3f0np0: XDP TX failed (-22)
However, without reverting the change, it makes the user to think that
everything is OK at probe time, but later it fails in an unpredictable
way, depending on the CPU that handles the packet.
It is better to restore the predictable behaviour. If the user sees the
error message at probe time, he/she can try to configure the best way it
fits his/her needs. At least, he/she will have 2 options:
- Accept that XDP_TX/REDIRECT is not available (he/she may not need it)
- Load sfc module with modparam 'rss_cpus' with a lower number, thus
creating less normal RX queues/channels, letting more free resources
for XDP, with some performance penalty.
Anyway, let the calculation of maximum TX queues that can be handled by
a single event queue, and use it only if it's less than the number of TX
queues per channel. This doesn't happen in practice, but could happen if
some constant values are tweaked in the future, such us
EFX_MAX_TXQ_PER_CHANNEL, EFX_MAX_EVQ_SIZE or EFX_MAX_DMAQ_SIZE.
Related mailing list thread:
https://lore.kernel.org/bpf/20201215104327.2be76156@carbon/
Signed-off-by: Íñigo Huguet <ihuguet@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Trivial conflict in net/netfilter/nf_tables_api.c.
Duplicate fix in tools/testing/selftests/net/devlink_port_split.py
- take the net-next version.
skmsg, and L4 bpf - keep the bpf code but remove the flags
and err params.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The sfc driver has rcu_read_lock()/rcu_read_unlock() pairs around XDP
program invocations. However, the actual lifetime of the objects referred
by the XDP program invocation is longer, all the way through to the call to
xdp_do_flush(), making the scope of the rcu_read_lock() too small. This
turns out to be harmless because it all happens in a single NAPI poll
cycle (and thus under local_bh_disable()), but it makes the rcu_read_lock()
misleading.
Rather than extend the scope of the rcu_read_lock(), just get rid of it
entirely. With the addition of RCU annotations to the XDP_REDIRECT map
types that take bh execution into account, lockdep even understands this to
be safe, so there's really no reason to keep it around.
Signed-off-by: Toke Høiland-Jørgensen <toke@redhat.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Edward Cree <ecree.xilinx@gmail.com>
Cc: Martin Habets <habetsm.xilinx@gmail.com>
Link: https://lore.kernel.org/bpf/20210624160609.292325-17-toke@redhat.com
The fail path of efx_ef10_sriov_alloc_vf_vswitching is identical to the
full content of efx_ef10_sriov_free_vf_vswitching, so replace it for a
single call to efx_ef10_sriov_free_vf_vswitching.
Signed-off-by: Íñigo Huguet <ihuguet@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
During SRIOV disabling it is checked wether any VF is currently attached
to a guest, using pci_vfs_assigned function. However, this check only
works with VFs attached with Xen, not with vfio/KVM. Added comments
clarifying this point.
Also, replaced manual check of PCI_DEV_FLAGS_ASSIGNED flag and used the
helper function pci_is_dev_assigned instead.
Signed-off-by: Íñigo Huguet <ihuguet@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If SRIOV cannot be disabled during device removal or module unloading,
return error code so it can be logged properly in the calling function.
Note that this can only happen if any VF is currently attached to a
guest using Xen, but not with vfio/KVM. Despite that in that case the
VFs won't work properly with PF removed and/or the module unloaded, I
have let it as is because I don't know what side effects may have
changing it, and also it seems to be the same that other drivers are
doing in this situation.
In the case of being called during SRIOV reconfiguration, the behavior
hasn't changed because the function is called with force=false.
Signed-off-by: Íñigo Huguet <ihuguet@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If pci_remove was called for a PF with VFs, the removal of the VFs was
called twice from efx_ef10_sriov_fini: one directly with pci_driver->remove
and another implicit by calling pci_disable_sriov, which also perform
the VFs remove. This was leading to crashing the kernel on the second
attempt.
Given that pci_disable_sriov already calls to pci remove function, get
rid of the direct call to pci_driver->remove from the driver.
2 different ways to trigger the bug:
- Create one or more VFs, then attach the PF to a virtual machine (at
least with qemu/KVM)
- Create one or more VFs, then remove the PF with:
echo 1 > /sys/bus/pci/devices/PF_PCI_ID/remove
Removing sfc module does not trigger the error, at least for me, because
it removes the VF first, and then the PF.
Example of a log with the error:
list_del corruption, ffff967fd20a8ad0->next is LIST_POISON1 (dead000000000100)
------------[ cut here ]------------
kernel BUG at lib/list_debug.c:47!
[...trimmed...]
RIP: 0010:__list_del_entry_valid.cold.1+0x12/0x4c
[...trimmed...]
Call Trace:
efx_dissociate+0x1f/0x140 [sfc]
efx_pci_remove+0x27/0x150 [sfc]
pci_device_remove+0x3b/0xc0
device_release_driver_internal+0x103/0x1f0
pci_stop_bus_device+0x69/0x90
pci_stop_and_remove_bus_device+0xe/0x20
pci_iov_remove_virtfn+0xba/0x120
sriov_disable+0x2f/0xe0
efx_ef10_pci_sriov_disable+0x52/0x80 [sfc]
? pcie_aer_is_native+0x12/0x40
efx_ef10_sriov_fini+0x72/0x110 [sfc]
efx_pci_remove+0x62/0x150 [sfc]
pci_device_remove+0x3b/0xc0
device_release_driver_internal+0x103/0x1f0
unbind_store+0xf6/0x130
kernfs_fop_write+0x116/0x190
vfs_write+0xa5/0x1a0
ksys_write+0x4f/0xb0
do_syscall_64+0x5b/0x1a0
entry_SYSCALL_64_after_hwframe+0x65/0xca
Signed-off-by: Íñigo Huguet <ihuguet@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use DEVICE_ATTR_*() helper instead of plain DEVICE_ATTR,
which makes the code a bit shorter and easier to read.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use DEVICE_ATTR_*() helper instead of plain DEVICE_ATTR,
which makes the code a bit shorter and easier to read.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
SFC driver can be configured via modparam to work using MSI-X, MSI or
legacy IRQ interrupts. In the last one, the interrupt was not properly
released on module remove.
It was not freed because the flag irqs_hooked was not set during
initialization in the case of using legacy IRQ.
Example of (trimmed) trace during module remove without this fix:
remove_proc_entry: removing non-empty directory 'irq/125', leaking at least '0000:3b:00.1'
WARNING: CPU: 39 PID: 3658 at fs/proc/generic.c:715 remove_proc_entry+0x15c/0x170
...trimmed...
Call Trace:
unregister_irq_proc+0xe3/0x100
free_desc+0x29/0x70
irq_free_descs+0x47/0x70
mp_unmap_irq+0x58/0x60
acpi_unregister_gsi_ioapic+0x2a/0x40
acpi_pci_irq_disable+0x78/0xb0
pci_disable_device+0xd1/0x100
efx_pci_remove+0xa1/0x1e0 [sfc]
pci_device_remove+0x38/0xa0
__device_release_driver+0x177/0x230
driver_detach+0xcb/0x110
bus_remove_driver+0x58/0xd0
pci_unregister_driver+0x2a/0xb0
efx_exit_module+0x24/0xf40 [sfc]
__do_sys_delete_module.constprop.0+0x171/0x280
? exit_to_user_mode_prepare+0x83/0x1d0
do_syscall_64+0x3d/0x80
entry_SYSCALL_64_after_hwframe+0x44/0xae
RIP: 0033:0x7f9f9385800b
...trimmed...
Signed-off-by: Íñigo Huguet <ihuguet@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix the following kernel build warning when CONFIG_SFC_SRIOV is disabled:
drivers/net/ethernet/sfc/farch.c: In function ‘efx_farch_dimension_resources’:
drivers/net/ethernet/sfc/farch.c:1671:21: warning: variable ‘buftbl_min’ set but not used [-Wunused-but-set-variable]
unsigned vi_count, buftbl_min, total_tx_channels;
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Using netif_info() before the net_device is registered results in ugly
messages like the following:
sfc 0000:01:00.1 (unnamed net_device) (uninitialized): Solarflare NIC detected
Therefore use pci_info() et al until net_device is registered.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
All callers pass 0 as offset. Therefore remove the parameter and use a
fixed offset 0 in pci_vpd_find_tag().
Link: https://lore.kernel.org/r/f62e6e19-5423-2ead-b2bd-62844b23ef8f@gmail.com
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
We're starting from a TXQ label, not a TXQ type, so
efx_channel_get_tx_queue() is inappropriate. This worked by chance,
because labels and types currently match on EF10, but we shouldn't
rely on that.
Fixes: 12804793b1 ("sfc: decouple TXQ type from label")
Signed-off-by: Edward Cree <ecree.xilinx@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We're starting from a TXQ label, not a TXQ type, so
efx_channel_get_tx_queue() is inappropriate (and could return NULL,
leading to panics).
Fixes: 12804793b1 ("sfc: decouple TXQ type from label")
Cc: stable@vger.kernel.org
Signed-off-by: Edward Cree <ecree.xilinx@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We're starting from a TXQ instance number ('qid'), not a TXQ type, so
efx_get_tx_queue() is inappropriate (and could return NULL, leading
to panics).
Fixes: 12804793b1 ("sfc: decouple TXQ type from label")
Reported-by: Trevor Hemsley <themsley@voiceflex.com>
Cc: stable@vger.kernel.org
Signed-off-by: Edward Cree <ecree.xilinx@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Report what appears to be the standard block counts:
- 30.5.1.1.17 aFECCorrectedBlocks
- 30.5.1.1.18 aFECUncorrectableBlocks
Don't report the per-lane symbol counts, if those really
count symbols they are not what the standard calls for
(even if symbols seem like the most useful thing to count.)
Fingers crossed that fec_corrected_errors is not in symbols.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix the following coccicheck warning:
./drivers/net/ethernet/sfc/enum.h:80:7-28: duplicated argument to |
Signed-off-by: Wan Jiabing <wanjiabing@vivo.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some lines of code can be merged into an equivalent 'skb_add_rx_frag()'
call which is less verbose.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Alexei Starovoitov says:
====================
pull-request: bpf-next 2021-03-24
The following pull-request contains BPF updates for your *net-next* tree.
We've added 37 non-merge commits during the last 15 day(s) which contain
a total of 65 files changed, 3200 insertions(+), 738 deletions(-).
The main changes are:
1) Static linking of multiple BPF ELF files, from Andrii.
2) Move drop error path to devmap for XDP_REDIRECT, from Lorenzo.
3) Spelling fixes from various folks.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
s/maintaning/maintaining/
Signed-off-by: Bhaskar Chowdhury <unixbhaskar@gmail.com>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Yang Guang
David S. Miller
Erik Ekman
Jakub Kicinski
Linus Torvalds
Íñigo Huguet
Heiner Kallweit
Yufeng Mo
Arnd Bergmann
Toke Høiland-Jørgensen
YueHaibing
Yang Yingliang
Ignat Korchagin
Edward Cree
Wan Jiabing
Christophe JAILLET
Bhaskar Chowdhury