commit 0363466866 (net offloading: Convert checksums to use
centrally computed features.) mistakenly swapped can_checksum_protocol()
arguments.
This broke IPv6 on bnx2 for instance, on NIC without TCPv6 checksum
offloads.
Reported-by: Hans de Bruin <jmdebruin@xmsnet.nl>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Acked-by: Jesse Gross <jesse@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If a DACL has entries for ACEs for SID Everyone and Authenticated Users,
factor in mask in respective entries during calculation of permissions
for all three, user, group, and other.
http://technet.microsoft.com/en-us/library/bb463216.aspx
Signed-off-by: Shirish Pargaonkar <shirishpargaonkar@gmail.com>
Reviewed-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: Steve French <sfrench@us.ibm.com>
NTLM response length was changed to 16 bytes instead of 24 bytes
that are sent in Tree Connection Request during share-level security
share mounts. Revert it back to 24 bytes.
Reported-and-Tested-by: Grzegorz Ozanski <grzegorz.ozanski@intel.com>
Acked-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: Shirish Pargaonkar <shirishpargaonkar@gmail.com>
Acked-by: Suresh Jayaraman <sjayaraman@suse.de>
Cc: stable@kernel.org
Signed-off-by: Steve French <sfrench@us.ibm.com>
Reviewed-by: Suresh Jayaraman <sjayaraman@suse.de>
Reviewed-by: Pavel Shilovsky <piastryyy@gmail.com>
Signed-off-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: Steve French <sfrench@us.ibm.com>
In later patches, we're going to need to have finer-grained control
over the addition and removal of these structs from the pending_mid_q
and we'll need to be able to call the destructor while holding the
spinlock. Move the locked sections out of both routines and into
the callers. Fix up current callers of DeleteMidQEntry to call a new
routine that dequeues the entry and then destroys it.
Reviewed-by: Suresh Jayaraman <sjayaraman@suse.de>
Reviewed-by: Pavel Shilovsky <piastryyy@gmail.com>
Signed-off-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: Steve French <sfrench@us.ibm.com>
It's an atomic_t and the code accesses the "counter" field in it directly
instead of using atomic_read(). It also is sometimes accessed under a
spinlock and sometimes not. Move it out of the spinlock since we don't need
belt-and-suspenders for something that's just informational.
Reviewed-by: Suresh Jayaraman <sjayaraman@suse.de>
Reviewed-by: Pavel Shilovsky <piastryyy@gmail.com>
Signed-off-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: Steve French <sfrench@us.ibm.com>
The cifsSesInfo pointer is only used to get at the server.
Reviewed-by: Suresh Jayaraman <sjayaraman@suse.de>
Reviewed-by: Pavel Shilovsky <piastryyy@gmail.com>
Signed-off-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: Steve French <sfrench@us.ibm.com>
The TCP_Server_Info is refcounted and every SMB session holds a
reference to it. Thus, smb_ses_list is always going to be empty when
cifsd is coming down. This is dead code.
Reviewed-by: Suresh Jayaraman <sjayaraman@suse.de>
Reviewed-by: Pavel Shilovsky <piastryyy@gmail.com>
Signed-off-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: Steve French <sfrench@us.ibm.com>
If CIFSSMBWrite2 returns -EAGAIN, then the error should be considered
temporary. CIFS should retry the write instead of setting an error on
the mapping and returning.
For WB_SYNC_ALL, just retry the write immediately. In the WB_SYNC_NONE
case, call redirty_page_for_writeback on all of the pages that didn't
get written out and then move on.
Also, fix up the handling of a short write with a successful return
code. MS-CIFS says that 0 bytes_written means ENOSPC or EFBIG. It
doesn't mention what a short, but non-zero write means, so for now
treat it as we would an -EAGAIN return.
Reviewed-by: Suresh Jayaraman <sjayaraman@suse.de>
Reviewed-by: Pavel Shilovsky <piastryyy@gmail.com>
Signed-off-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: Steve French <sfrench@us.ibm.com>
When we get oplock break notification we should set the appropriate
value of OplockLevel field in oplock break acknowledge according to
the oplock level held by the client in this time. As we only can have
level II oplock or no oplock in the case of oplock break, we should be
aware only about clientCanCacheRead field in cifsInodeInfo structure.
Also fix bug connected with wrong interpretation of OplockLevel field
during oplock break notification processing.
Signed-off-by: Pavel Shilovsky <piastryyy@gmail.com>
Cc: <stable@kernel.org>
Signed-off-by: Steve French <sfrench@us.ibm.com>
sound/pci/hda/patch_realtek.c: In function ‘alc_apply_fixup’:
sound/pci/hda/patch_realtek.c:1724:14: warning: unused variable ‘modelname’
snd_printdd() is evaluated only when CONFIG_SND_DEBUG_VERBOSE=y.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Commit a4f740cf, "of/flattree: Add of_flat_dt_match() helper function"
introduced build failures in arch/powerpc/platform/83xx by mistyping
'static' as 'struct' in the compatible string list, and omitting a few
semicolons. This patch fixes it.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
When the lirc drivers were converted over to using memdup_user, I
mistakenly also removed corresponding calls to kfree. Add those back. I
also screwed up on the allocation error check in lirc_serial, using if
(PTR_ERR()) instead of if (IS_ERR()), which broke transmit.
Reported-by: Jiri Fojtasek <jiri.fojtasek@hlohovec.net>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The current hdpvr code kmalloc's a new buffer for every i2c read and
write. Rather than do that, lets allocate a buffer in the driver's
device struct and just use that every time.
The size I've chosen for the buffer is the maximum size I could
ascertain might be used by either ir-kbd-i2c or lirc_zilog, plus a bit
of padding (lirc_zilog may use up to 100 bytes on tx, rounded that up
to 128).
Note that this might also remedy user reports of very sluggish behavior
of IR receive with hdpvr hardware.
v2: make sure (len <= (dev->i2c_buf)) [Jean Delvare]
Reported-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
A number of things going on here, but the end result is that the IR part
on the hdpvr gets enabled, and can be used with ir-kbd-i2c and/or
lirc_zilog.
First up, there are some conditional build fixes that come into play
whether i2c is built-in or modular. Second, we're swapping out
i2c_new_probed_device() for i2c_new_device(), as in my testing, probing
always fails, but we *know* that all hdpvr devices have a z8 chip at
0x70 and 0x71. Third, we're poking at an i2c address directly without a
client, and writing some magic bits to actually turn on this IR part
(this could use some improvement in the future). Fourth, some of the
i2c_adapter storage has been reworked, as the existing implementation
used to lead to an oops following i2c changes c. 2.6.31.
Earlier editions of this patch have been floating around the 'net for a
while, including being patched into Fedora kernels, and they *do* work.
This specific version isn't yet tested, beyond loading ir-kbd-i2c and
confirming that it does bind to the RX address of the hdpvr.
[mchehab@redhat.com: I2C_CLASS_TV_ANALOG is not defined. Fix compilation bug]
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Acked-by: Andy Walls <awalls@md.metrocast.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Fixes an egregious bug in mceusb driver, where the receiver was being
put into idle mode far sooner than it should have, thanks to storing a
timeout value that in us where it should be ns. Basically, the receiver
kept going into idle mode before a trailing space had been fully
received, which was causing problems for some protocols, most notably
manifesting as lirc userspace never receiving a trailing space for any
rc5 signals.
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Fix a bug in v4l2_device_unregister where the sd pointer can be dereferenced
after it was freed.
Normally the i2c adapter is removed before this function is called. Removing
the adapter will also unregister all subdevs on that adapter, so generally
v4l2_device_unregister has nothing to do. However, in the case of a platform
i2c bus that bus is generally not freed.
In that case, after freeing the i2c subdevice the code will fall into the
second block when it tests if the subdev is a SPI device. But by that time
the subdev is already freed and the kernel oopses.
The fix is trivial: continue with the loop after freeing the i2c or spi
subdevice.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Reported-by: Daniel Drake <dsd@laptop.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Zeroing video_device.dev causes a memory leak if video_set_drvdata
was called before video_register_device was called. video_set_drvdata
calls dev_set_drvdata which allocates video_device.dev.p.
memsetting this will prevent freeing of that memory.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
After a detach zero the whole device state to ensure a clean slate
on the next attach.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
v4l2_queryctrl sets the step value based on the control type. That would
be fine if it used the control type stored in the V4L2 kernel control
object, not the one stored in the userspace ioctl structure that has
just been memset to 0. Fix this.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The later makes extensive use of structures defined in the former.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
When queryctrl is called with a V4L2_CID_PRIVATE_BASE control ID, then
currently it is replaced by the real internal ID. This is not according to
the spec so keep the V4L2_CID_PRIVATE_BASE ID in this case.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
VIDIOC_S_CTRL did not check against read-only controls. Even worse, for
controls of type CTRL_CLASS it would cause a kernel oops since those controls
do not have a s_ctrl op.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
When registering an IR Rx device with the I2C subsystem, provide more detailed
information about the IR device and default remote configuration for the IR
driver modules.
Also explicitly register any IR Tx device with the I2C subsystem.
Signed-off-by: Andy Walls <awalls@md.metrocast.net>
Acked-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This reverts a portion of commit
44243fc2ef
A commit for which I errantly recommended that defaults for I2C address
0x71 not be set by ir-kbd-i2c.c
The pvrusb2 and bttv drivers currently rely on ir-kbd-i2c setting
defaults for that address. Until I can get those bridge drivers fixed
to properly send IR_i2c_init_data for boards with Zilog Z8 chips,
just add back the default settings for I2C address 0x71.
Signed-off-by: Andy Walls <awalls@md.metrocast.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The ir_command() function is a do-nothing stub; remove it.
Signed-off-by: Andy Walls <awalls@md.metrocast.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The driver is now structured so that it must handle an IR Tx unit
for a Z8 IR chip, or it refuses to handle that Z8 IR chip. This
allows us to assume that ir->tx != NULL in a few places in the driver,
and also allows us to always report Tx is available to userspace.
Get rid of unneeded tests for ir->tx == NULL and always report that
Tx is available.
Signed-off-by: Andy Walls <awalls@md.metrocast.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The IR Rx polling thread was originally a kernel_thread long ago,
and had only been minimally converted to a kthread. This patch
finishes that conversion by
- cleaning up all the unneeded completions
- destroying the kthread properly by calling kthread_stop()
- changing lirc_thread() to test kthread_should_stop() just before
every point where it may sleep
- reorganizing the lirc_thread() function so it uses fewer lines
- modifying the name of the kthread from "lirc_zilog" to
"zilog-rx-i2c-N", so ps will show which kthread polls
which Zilog Z8 IR unit.
Also some minor tweaks were made to logging emitted by the
ir_probe() function.
Signed-off-by: Andy Walls <awalls@md.metrocast.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch is an extensive rework of the ir_probe() and ir_remove() functions.
It removes all the double binding and allocation problems on module load.
It removes almost all the memory leaks on module exit and on device
instantiation failure. Proper destruction of the Rx polling kthread still
needs investigation and more work, but it is no worse than it already was.
This rework also had side effects that include:
- encapsulation of the ir_devices[] array
- serialization of access to the ir_devices[] array
- semantic change of the module parameter "disable_rx" to "tx_only"
If tx_only is true, the module does not claim the i2c_client for the IR Rx
function, and only claims and handles the i2c_client for the IR Tx function.
This is a first step in providing the option of letting ir-kbd-i2c.c handle
IR Rx function, while lirc_zilog handles the IR Tx function.
Signed-off-by: Andy Walls <awalls@md.metrocast.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Don't make private copies of the i2c clients provided by the I2C
subsystem, don't change the client address field, and don't probe
the client addresses - the bridge driver already did that. This
moves us to the proper I2C and binding model.
Signed-off-by: Andy Walls <awalls@md.metrocast.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This change is a mostly mechanical break of the main struct IR
data structure into common, Rx, and Tx structures. There were some
small logical changes required as well, such as eliminating "is_hdpvr",
to accomplish this.
This change is an intiial step in reworking lirc_zilog to decouple the
Rx and Tx handling as much as possible to fit with the new I2C
binding model. This change actually makes lirc_zilog a little more
broken than it already was - memory deallocation in particular got worse.
However, this change makes the remaining problems easier to see and address.
Signed-off-by: Andy Walls <awalls@md.metrocast.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The only reason to use the lirc_zilog module is for IR Tx, so remove
the possibility of disabling IR Tx. If the user needs only IR Rx,
then the ir-kbd-i2c module works just fine, and doesn't require a
"firmware" image.
Signed-off-by: Andy Walls <awalls@md.metrocast.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Jean Delvare <khali@linux-fr.org> suggested this better
format for debug output in ir_probe().
Signed-off-by: Andy Walls <awalls@md.metrocast.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
After a recent update of xf86-input-evdev and xorg-server, I noticed
that X11 applications did not receive keypresses from the FireDTV
infrared remote control anymore. Instead, the Xorg log featured lots of
"FireDTV remote control: dropping event due to full queue!"
exclamations. The Linux console did not have an issue with the
FireDTV's RC though.
The fix is to insert EV_SYN events after the key-down/-up events.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Rework device init part. Move common code part to a function.
Usefull for register multiple devices like video, radio, vbi etc.
Signed-off-by: Beholder Intl. Ltd. Dmitry Belimov <d.belimov@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Commit e3c9221519 ("[media] radio-aimslab.c: Fix
gcc 4.5+ bug") removed the include, but introduced new callers of msleep():
| drivers/media/radio/radio-aimslab.c: In function ‘rt_decvol’:
| drivers/media/radio/radio-aimslab.c:76: error: implicit declaration of function ‘msleep’
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Fix sparse warning for non-ANSI function declaration:
drivers/media/rc/ir-raw.c:247:30: warning: non-ANSI function declaration of function 'ir_raw_get_allowed_protocols'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Cc: Mauro Carvalho Chehab <mchehab@infradead.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch adds s_power support to adv7175 driver. Power-down is done
by power-down all four DACs.
Signed-off-by: Christian Gmeiner <christian.gmeiner@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
info->num comes from the user. It's type int. If the user passes
in a negative value that would cause memory corruption.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
My initial thinking was that we should default to mouse mode, so people
could use the mouse function to click on something on a login screen,
but a lot of systems where a remote is useful automatically log in a
user and launch a media center application, some of which hide the
mouse, which can be confusing to users if they punch buttons on the
remote and don't see any feedback. Plus, first and foremost, its a
remote, so lets default to being a remote, and only toggle into mouse
mode when the user explicitly asks for it. As a nice side-effect, this
actually simplifies some of the code a fair bit...
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The ene_ir driver was using a private define of MS_TO_NS, which is meant
to be microseconds to nanoseconds. The mceusb driver copied it,
intending to use is a milliseconds to microseconds. Lets move the
defines to a common location, expand and standardize them a touch, so
that we now have:
MS_TO_NS - milliseconds to nanoseconds
MS_TO_US - milliseconds to microseconds
US_TO_NS - microseconds to nanoseconds
Reported-by: David Härdeman <david@hardeman.nu>
CC: Maxim Levitsky <maximlevitsky@gmail.com>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Otherwise, we have a null receive buffer, and the logic all falls down,
goes boom, all ffdc devs wind up as imon IR w/VFD. Oops.
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Eric Dumazet
David S. Miller
Shirish Pargaonkar
Steve French
Jeff Layton
Pavel Shilovsky
Takashi Iwai
Grant Likely
Jarod Wilson
Hans Verkuil
Laurent Pinchart
Andy Walls
Stefan Richter
Dmitri Belimov
Geert Uytterhoeven
Randy Dunlap
Christian Gmeiner
Dan Carpenter