sk_validate_xmit_skb() and drivers depend on the sk member of
struct sk_buff to identify segments requiring encryption.
Any operation which removes or does not preserve the original TLS
socket such as skb_orphan() or skb_clone() will cause clear text
leaks.
Make the TCP socket underlying an offloaded TLS connection
mark all skbs as decrypted, if TLS TX is in offload mode.
Then in sk_validate_xmit_skb() catch skbs which have no socket
(or a socket with no validation) and decrypted flag set.
Note that CONFIG_SOCK_VALIDATE_XMIT, CONFIG_TLS_DEVICE and
sk->sk_validate_xmit_skb are slightly interchangeable right now,
they all imply TLS offload. The new checks are guarded by
CONFIG_TLS_DEVICE because that's the option guarding the
sk_buff->decrypted member.
Second, smaller issue with orphaning is that it breaks
the guarantee that packets will be delivered to device
queues in-order. All TLS offload drivers depend on that
scheduling property. This means skb_orphan_partial()'s
trick of preserving partial socket references will cause
issues in the drivers. We need a full orphan, and as a
result netem delay/throttling will cause all TLS offload
skbs to be dropped.
Reusing the sk_buff->decrypted flag also protects from
leaking clear text when incoming, decrypted skb is redirected
(e.g. by TC).
See commit 0608c69c9a ("bpf: sk_msg, sock{map|hash} redirect
through ULP") for justification why the internal flag is safe.
The only location which could leak the flag in is tcp_bpf_sendmsg(),
which is taken care of by clearing the previously unused bit.
v2:
- remove superfluous decrypted mark copy (Willem);
- remove the stale doc entry (Boris);
- rely entirely on EOR marking to prevent coalescing (Boris);
- use an internal sendpages flag instead of marking the socket
(Boris).
v3 (Willem):
- reorganize the can_skb_orphan_partial() condition;
- fix the flag leak-in through tcp_bpf_sendmsg.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Acked-by: Willem de Bruijn <willemb@google.com>
Reviewed-by: Boris Pismenny <borisp@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
socket->wq is assign-once, set when we are initializing both
struct socket it's in and struct socket_wq it points to. As the
matter of fact, the only reason for separate allocation was the
ability to RCU-delay freeing of socket_wq. RCU-delaying the
freeing of socket itself gets rid of that need, so we can just
fold struct socket_wq into the end of struct socket and simplify
the life both for sock_alloc_inode() (one allocation instead of
two) and for tun/tap oddballs, where we used to embed struct socket
and struct socket_wq into the same structure (now - embedding just
the struct socket).
Note that reference to struct socket_wq in struct sock does remain
a reference - that's unchanged.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
>From linux-3.7, (commit 5640f76858 "net: use a per task frag
allocator") TCP sendmsg() has preferred using order-3 allocations.
While it gives good results for most cases, we had reports
that heavy uses of TCP over loopback were hitting a spinlock
contention in page allocations/freeing.
This commits adds a sysctl so that admins can opt-in
for order-0 allocations. Hopefully mm layer might optimize
order-3 allocations in the future since it could give us
a nice boost (see 8 lines of following benchmark)
The following benchmark shows a win when more than 8 TCP_STREAM
threads are running (56 x86 cores server in my tests)
for thr in {1..30}
do
sysctl -wq net.core.high_order_alloc_disable=0
T0=`./super_netperf $thr -H 127.0.0.1 -l 15`
sysctl -wq net.core.high_order_alloc_disable=1
T1=`./super_netperf $thr -H 127.0.0.1 -l 15`
echo $thr:$T0:$T1
done
1: 49979: 37267
2: 98745: 76286
3: 141088: 110051
4: 177414: 144772
5: 197587: 173563
6: 215377: 208448
7: 241061: 234087
8: 267155: 263373
9: 295069: 297402
10: 312393: 335213
11: 340462: 368778
12: 371366: 403954
13: 412344: 443713
14: 426617: 473580
15: 474418: 507861
16: 503261: 538539
17: 522331: 563096
18: 532409: 567084
19: 550824: 605240
20: 525493: 641988
21: 564574: 665843
22: 567349: 690868
23: 583846: 710917
24: 588715: 736306
25: 603212: 763494
26: 604083: 792654
27: 602241: 796450
28: 604291: 797993
29: 611610: 833249
30: 577356: 841062
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Feng Tang reported a performance regression after introduction
of per TCP socket tx/rx caches, for TCP over loopback (netperf)
There is high chance the regression is caused by a change on
how well the 32 KB per-thread page (current->task_frag) can
be recycled, and lack of pcp caches for order-3 pages.
I could not reproduce the regression myself, cpus all being
spinning on the mm spinlocks for page allocs/freeing, regardless
of enabling or disabling the per tcp socket caches.
It seems best to disable the feature by default, and let
admins enabling it.
MM layer either needs to provide scalable order-3 pages
allocations, or could attempt a trylock on zone->lock if
the caller only attempts to get a high-order page and is
able to fallback to order-0 ones in case of pressure.
Tests run on a 56 cores host (112 hyper threads)
- 35.49% netperf [kernel.vmlinux] [k] queued_spin_lock_slowpath
- 35.49% queued_spin_lock_slowpath
- 18.18% get_page_from_freelist
- __alloc_pages_nodemask
- 18.18% alloc_pages_current
skb_page_frag_refill
sk_page_frag_refill
tcp_sendmsg_locked
tcp_sendmsg
inet_sendmsg
sock_sendmsg
__sys_sendto
__x64_sys_sendto
do_syscall_64
entry_SYSCALL_64_after_hwframe
__libc_send
+ 17.31% __free_pages_ok
+ 31.43% swapper [kernel.vmlinux] [k] intel_idle
+ 9.12% netperf [kernel.vmlinux] [k] copy_user_enhanced_fast_string
+ 6.53% netserver [kernel.vmlinux] [k] copy_user_enhanced_fast_string
+ 0.69% netserver [kernel.vmlinux] [k] queued_spin_lock_slowpath
+ 0.68% netperf [kernel.vmlinux] [k] skb_release_data
+ 0.52% netperf [kernel.vmlinux] [k] tcp_sendmsg_locked
0.46% netperf [kernel.vmlinux] [k] _raw_spin_lock_irqsave
Fixes: 472c2e07ee ("tcp: add one skb cache for tx")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Feng Tang <feng.tang@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of relying on rps_needed, it is safer to use a separate
static key, since we do not want to enable TCP rx_skb_cache
by default. This feature can cause huge increase of memory
usage on hosts with millions of sockets.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 3029 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190527070032.746973796@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It is illegal to change arbitrary fields in skb_shared_info if the
skb is cloned.
Before calling skb_zcopy_clear() we need to ensure this rule,
therefore we need to move the test from sk_stream_alloc_skb()
to sk_wmem_free_skb()
Fixes: 4f661542a4 ("tcp: fix zerocopy and notsent_lowat issues")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Diagnosed-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After allowing a bpf prog to
- directly read the skb->sk ptr
- get the fullsock bpf_sock by "bpf_sk_fullsock()"
- get the bpf_tcp_sock by "bpf_tcp_sock()"
- get the listener sock by "bpf_get_listener_sock()"
- avoid duplicating the fields of "(bpf_)sock" and "(bpf_)tcp_sock"
into different bpf running context.
this patch is another effort to make bpf's network programming
more intuitive to do (together with memory and performance benefit).
When bpf prog needs to store data for a sk, the current practice is to
define a map with the usual 4-tuples (src/dst ip/port) as the key.
If multiple bpf progs require to store different sk data, multiple maps
have to be defined. Hence, wasting memory to store the duplicated
keys (i.e. 4 tuples here) in each of the bpf map.
[ The smallest key could be the sk pointer itself which requires
some enhancement in the verifier and it is a separate topic. ]
Also, the bpf prog needs to clean up the elem when sk is freed.
Otherwise, the bpf map will become full and un-usable quickly.
The sk-free tracking currently could be done during sk state
transition (e.g. BPF_SOCK_OPS_STATE_CB).
The size of the map needs to be predefined which then usually ended-up
with an over-provisioned map in production. Even the map was re-sizable,
while the sk naturally come and go away already, this potential re-size
operation is arguably redundant if the data can be directly connected
to the sk itself instead of proxy-ing through a bpf map.
This patch introduces sk->sk_bpf_storage to provide local storage space
at sk for bpf prog to use. The space will be allocated when the first bpf
prog has created data for this particular sk.
The design optimizes the bpf prog's lookup (and then optionally followed by
an inline update). bpf_spin_lock should be used if the inline update needs
to be protected.
BPF_MAP_TYPE_SK_STORAGE:
-----------------------
To define a bpf "sk-local-storage", a BPF_MAP_TYPE_SK_STORAGE map (new in
this patch) needs to be created. Multiple BPF_MAP_TYPE_SK_STORAGE maps can
be created to fit different bpf progs' needs. The map enforces
BTF to allow printing the sk-local-storage during a system-wise
sk dump (e.g. "ss -ta") in the future.
The purpose of a BPF_MAP_TYPE_SK_STORAGE map is not for lookup/update/delete
a "sk-local-storage" data from a particular sk.
Think of the map as a meta-data (or "type") of a "sk-local-storage". This
particular "type" of "sk-local-storage" data can then be stored in any sk.
The main purposes of this map are mostly:
1. Define the size of a "sk-local-storage" type.
2. Provide a similar syscall userspace API as the map (e.g. lookup/update,
map-id, map-btf...etc.)
3. Keep track of all sk's storages of this "type" and clean them up
when the map is freed.
sk->sk_bpf_storage:
------------------
The main lookup/update/delete is done on sk->sk_bpf_storage (which
is a "struct bpf_sk_storage"). When doing a lookup,
the "map" pointer is now used as the "key" to search on the
sk_storage->list. The "map" pointer is actually serving
as the "type" of the "sk-local-storage" that is being
requested.
To allow very fast lookup, it should be as fast as looking up an
array at a stable-offset. At the same time, it is not ideal to
set a hard limit on the number of sk-local-storage "type" that the
system can have. Hence, this patch takes a cache approach.
The last search result from sk_storage->list is cached in
sk_storage->cache[] which is a stable sized array. Each
"sk-local-storage" type has a stable offset to the cache[] array.
In the future, a map's flag could be introduced to do cache
opt-out/enforcement if it became necessary.
The cache size is 16 (i.e. 16 types of "sk-local-storage").
Programs can share map. On the program side, having a few bpf_progs
running in the networking hotpath is already a lot. The bpf_prog
should have already consolidated the existing sock-key-ed map usage
to minimize the map lookup penalty. 16 has enough runway to grow.
All sk-local-storage data will be removed from sk->sk_bpf_storage
during sk destruction.
bpf_sk_storage_get() and bpf_sk_storage_delete():
------------------------------------------------
Instead of using bpf_map_(lookup|update|delete)_elem(),
the bpf prog needs to use the new helper bpf_sk_storage_get() and
bpf_sk_storage_delete(). The verifier can then enforce the
ARG_PTR_TO_SOCKET argument. The bpf_sk_storage_get() also allows to
"create" new elem if one does not exist in the sk. It is done by
the new BPF_SK_STORAGE_GET_F_CREATE flag. An optional value can also be
provided as the initial value during BPF_SK_STORAGE_GET_F_CREATE.
The BPF_MAP_TYPE_SK_STORAGE also supports bpf_spin_lock. Together,
it has eliminated the potential use cases for an equivalent
bpf_map_update_elem() API (for bpf_prog) in this patch.
Misc notes:
----------
1. map_get_next_key is not supported. From the userspace syscall
perspective, the map has the socket fd as the key while the map
can be shared by pinned-file or map-id.
Since btf is enforced, the existing "ss" could be enhanced to pretty
print the local-storage.
Supporting a kernel defined btf with 4 tuples as the return key could
be explored later also.
2. The sk->sk_lock cannot be acquired. Atomic operations is used instead.
e.g. cmpxchg is done on the sk->sk_bpf_storage ptr.
Please refer to the source code comments for the details in
synchronization cases and considerations.
3. The mem is charged to the sk->sk_omem_alloc as the sk filter does.
Benchmark:
---------
Here is the benchmark data collected by turning on
the "kernel.bpf_stats_enabled" sysctl.
Two bpf progs are tested:
One bpf prog with the usual bpf hashmap (max_entries = 8192) with the
sk ptr as the key. (verifier is modified to support sk ptr as the key
That should have shortened the key lookup time.)
Another bpf prog is with the new BPF_MAP_TYPE_SK_STORAGE.
Both are storing a "u32 cnt", do a lookup on "egress_skb/cgroup" for
each egress skb and then bump the cnt. netperf is used to drive
data with 4096 connected UDP sockets.
BPF_MAP_TYPE_HASH with a modifier verifier (152ns per bpf run)
27: cgroup_skb name egress_sk_map tag 74f56e832918070b run_time_ns 58280107540 run_cnt 381347633
loaded_at 2019-04-15T13:46:39-0700 uid 0
xlated 344B jited 258B memlock 4096B map_ids 16
btf_id 5
BPF_MAP_TYPE_SK_STORAGE in this patch (66ns per bpf run)
30: cgroup_skb name egress_sk_stora tag d4aa70984cc7bbf6 run_time_ns 25617093319 run_cnt 390989739
loaded_at 2019-04-15T13:47:54-0700 uid 0
xlated 168B jited 156B memlock 4096B map_ids 17
btf_id 6
Here is a high-level picture on how are the objects organized:
sk
┌──────┐
│ │
│ │
│ │
│*sk_bpf_storage─────▶ bpf_sk_storage
└──────┘ ┌───────┐
┌───────────┤ list │
│ │ │
│ │ │
│ │ │
│ └───────┘
│
│ elem
│ ┌────────┐
├─▶│ snode │
│ ├────────┤
│ │ data │ bpf_map
│ ├────────┤ ┌─────────┐
│ │map_node│◀─┬─────┤ list │
│ └────────┘ │ │ │
│ │ │ │
│ elem │ │ │
│ ┌────────┐ │ └─────────┘
└─▶│ snode │ │
├────────┤ │
bpf_map │ data │ │
┌─────────┐ ├────────┤ │
│ list ├───────▶│map_node│ │
│ │ └────────┘ │
│ │ │
│ │ elem │
└─────────┘ ┌────────┐ │
┌─▶│ snode │ │
│ ├────────┤ │
│ │ data │ │
│ ├────────┤ │
│ │map_node│◀─┘
│ └────────┘
│
│
│ ┌───────┐
sk └──────────│ list │
┌──────┐ │ │
│ │ │ │
│ │ │ │
│ │ └───────┘
│*sk_bpf_storage───────▶bpf_sk_storage
└──────┘
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
The SIOCGSTAMP/SIOCGSTAMPNS ioctl commands are implemented by many
socket protocol handlers, and all of those end up calling the same
sock_get_timestamp()/sock_get_timestampns() helper functions, which
results in a lot of duplicate code.
With the introduction of 64-bit time_t on 32-bit architectures, this
gets worse, as we then need four different ioctl commands in each
socket protocol implementation.
To simplify that, let's add a new .gettstamp() operation in
struct proto_ops, and move ioctl implementation into the common
sock_ioctl()/compat_sock_ioctl_trans() functions that these all go
through.
We can reuse the sock_get_timestamp() implementation, but generalize
it so it can deal with both native and compat mode, as well as
timeval and timespec structures.
Acked-by: Stefan Schmidt <stefan@datenfreihafen.org>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Acked-by: Marc Kleine-Budde <mkl@pengutronix.de>
Link: https://lore.kernel.org/lkml/CAK8P3a038aDQQotzua_QtKGhq8O9n+rdiz2=WDCp82ys8eUT+A@mail.gmail.com/
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
fcntl(fd, F_SETOWN, getpid()) selects the recipient of SIGURG signals
that are delivered when out-of-band data arrives on socket fd.
If an SMC socket program makes use of such an fcntl() call, it fails
in case of fallback to TCP-mode. In case of fallback the traffic is
processed with the internal TCP socket. Propagating field "file" from the
SMC socket to the internal TCP socket fixes the issue.
Reviewed-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
My recent patch had at least three problems :
1) TX zerocopy wants notification when skb is acknowledged,
thus we need to call skb_zcopy_clear() if the skb is
cached into sk->sk_tx_skb_cache
2) Some applications might expect precise EPOLLOUT
notifications, so we need to update sk->sk_wmem_queued
and call sk_mem_uncharge() from sk_wmem_free_skb()
in all cases. The SOCK_QUEUE_SHRUNK flag must also be set.
3) Reuse of saved skb should have used skb_cloned() instead
of simply checking if the fast clone has been freed.
Fixes: 472c2e07ee ("tcp: add one skb cache for tx")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Willem de Bruijn <willemb@google.com>
Cc: Soheil Hassas Yeganeh <soheil@google.com>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Tested-by: Holger Hoffstätte <holger@applied-asynchrony.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Often times, recvmsg() system calls and BH handling for a particular
TCP socket are done on different cpus.
This means the incoming skb had to be allocated on a cpu,
but freed on another.
This incurs a high spinlock contention in slab layer for small rpc,
but also a high number of cache line ping pongs for larger packets.
A full size GRO packet might use 45 page fragments, meaning
that up to 45 put_page() can be involved.
More over performing the __kfree_skb() in the recvmsg() context
adds a latency for user applications, and increase probability
of trapping them in backlog processing, since the BH handler
might found the socket owned by the user.
This patch, combined with the prior one increases the rpc
performance by about 10 % on servers with large number of cores.
(tcp_rr workload with 10,000 flows and 112 threads reach 9 Mpps
instead of 8 Mpps)
This also increases single bulk flow performance on 40Gbit+ links,
since in this case there are often two cpus working in tandem :
- CPU handling the NIC rx interrupts, feeding the receive queue,
and (after this patch) freeing the skbs that were consumed.
- CPU in recvmsg() system call, essentially 100 % busy copying out
data to user space.
Having at most one skb in a per-socket cache has very little risk
of memory exhaustion, and since it is protected by socket lock,
its management is essentially free.
Note that if rps/rfs is used, we do not enable this feature, because
there is high chance that the same cpu is handling both the recvmsg()
system call and the TCP rx path, but that another cpu did the skb
allocations in the device driver right before the RPS/RFS logic.
To properly handle this case, it seems we would need to record
on which cpu skb was allocated, and use a different channel
to give skbs back to this cpu.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On hosts with a lot of cores, RPC workloads suffer from heavy contention on slab spinlocks.
20.69% [kernel] [k] queued_spin_lock_slowpath
5.64% [kernel] [k] _raw_spin_lock
3.83% [kernel] [k] syscall_return_via_sysret
3.48% [kernel] [k] __entry_text_start
1.76% [kernel] [k] __netif_receive_skb_core
1.64% [kernel] [k] __fget
For each sendmsg(), we allocate one skb, and free it at the time ACK packet comes.
In many cases, ACK packets are handled by another cpus, and this unfortunately
incurs heavy costs for slab layer.
This patch uses an extra pointer in socket structure, so that we try to reuse
the same skb and avoid these expensive costs.
We cache at most one skb per socket so this should be safe as far as
memory pressure is concerned.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We prefer static_branch_unlikely() over static_key_false() these days.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When using fanouts with AF_PACKET, the demux functions such as
fanout_demux_cpu will return an index in the fanout socket array, which
corresponds to the selected socket.
The ordering of this array depends on the order the sockets were added
to a given fanout group, so for FANOUT_CPU this means sockets are bound
to cpus in the order they are configured, which is OK.
However, when stopping then restarting the interface these sockets are
bound to, the sockets are reassigned to the fanout group in the reverse
order, due to the fact that they were inserted at the head of the
interface's AF_PACKET socket list.
This means that traffic that was directed to the first socket in the
fanout group is now directed to the last one after an interface restart.
In the case of FANOUT_CPU, traffic from CPU0 will be directed to the
socket that used to receive traffic from the last CPU after an interface
restart.
This commit introduces a helper to add a socket at the tail of a list,
then uses it to register AF_PACKET sockets.
Note that this changes the order in which sockets are listed in /proc and
with sock_diag.
Fixes: dc99f60069 ("packet: Add fanout support")
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The netfilter conflicts were rather simple overlapping
changes.
However, the cls_tcindex.c stuff was a bit more complex.
On the 'net' side, Cong is fixing several races and memory
leaks. Whilst on the 'net-next' side we have Vlad adding
the rtnl-ness support.
What I've decided to do, in order to resolve this, is revert the
conversion over to using a workqueue that Cong did, bringing us back
to pure RCU. I did it this way because I believe that either Cong's
races don't apply with have Vlad did things, or Cong will have to
implement the race fix slightly differently.
Signed-off-by: David S. Miller <davem@davemloft.net>
With many active TCP sockets, fat TCP sockets could fool
__sk_mem_raise_allocated() thanks to an overflow.
They would increase their share of the memory, instead
of decreasing it.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Al Viro mentioned (Message-ID
<20170626041334.GZ10672@ZenIV.linux.org.uk>)
that there is probably a race condition
lurking in accesses of sk_stamp on 32-bit machines.
sock->sk_stamp is of type ktime_t which is always an s64.
On a 32 bit architecture, we might run into situations of
unsafe access as the access to the field becomes non atomic.
Use seqlocks for synchronization.
This allows us to avoid using spinlocks for readers as
readers do not need mutual exclusion.
Another approach to solve this is to require sk_lock for all
modifications of the timestamps. The current approach allows
for timestamps to have their own lock: sk_stamp_lock.
This allows for the patch to not compete with already
existing critical sections, and side effects are limited
to the paths in the patch.
The addition of the new field maintains the data locality
optimizations from
commit 9115e8cd2a ("net: reorganize struct sock for better data
locality")
Note that all the instances of the sk_stamp accesses
are either through the ioctl or the syscall recvmsg.
Signed-off-by: Deepa Dinamani <deepa.kernel@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Lots of conflicts, by happily all cases of overlapping
changes, parallel adds, things of that nature.
Thanks to Stephen Rothwell, Saeed Mahameed, and others
for their guidance in these resolutions.
Signed-off-by: David S. Miller <davem@davemloft.net>
SOF_TIMESTAMPING_OPT_ID is supported on TCP, UDP and RAW sockets.
But it was missing on RAW with IPPROTO_IP, PF_PACKET and CAN.
Add skb_setup_tx_timestamp that configures both tx_flags and tskey
for these paths that do not need corking or use bytestream keys.
Fixes: 09c2d251b7 ("net-timestamp: add key to disambiguate concurrent datagrams")
Signed-off-by: Willem de Bruijn <willemb@google.com>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
TCP_NOTSENT_LOWAT socket option or sysctl was added in linux-3.12
as a step to enable bigger tcp sndbuf limits.
It works reasonably well, but the following happens :
Once the limit is reached, TCP stack generates
an [E]POLLOUT event for every incoming ACK packet.
This causes a high number of context switches.
This patch implements the strategy David Miller added
in sock_def_write_space() :
- If TCP socket has a notsent_lowat constraint of X bytes,
allow sendmsg() to fill up to X bytes, but send [E]POLLOUT
only if number of notsent bytes is below X/2
This considerably reduces TCP_NOTSENT_LOWAT overhead,
while allowing to keep the pipe full.
Tested:
100 ms RTT netem testbed between A and B, 100 concurrent TCP_STREAM
A:/# cat /proc/sys/net/ipv4/tcp_wmem
4096 262144 64000000
A:/# super_netperf 100 -H B -l 1000 -- -K bbr &
A:/# grep TCP /proc/net/sockstat
TCP: inuse 203 orphan 0 tw 19 alloc 414 mem 1364904 # This is about 54 MB of memory per flow :/
A:/# vmstat 5 5
procs -----------memory---------- ---swap-- -----io---- -system-- ------cpu-----
r b swpd free buff cache si so bi bo in cs us sy id wa st
0 0 0 256220672 13532 694976 0 0 10 0 28 14 0 1 99 0 0
2 0 0 256320016 13532 698480 0 0 512 0 715901 5927 0 10 90 0 0
0 0 0 256197232 13532 700992 0 0 735 13 771161 5849 0 11 89 0 0
1 0 0 256233824 13532 703320 0 0 512 23 719650 6635 0 11 89 0 0
2 0 0 256226880 13532 705780 0 0 642 4 775650 6009 0 12 88 0 0
A:/# echo 2097152 >/proc/sys/net/ipv4/tcp_notsent_lowat
A:/# grep TCP /proc/net/sockstat
TCP: inuse 203 orphan 0 tw 19 alloc 414 mem 86411 # 3.5 MB per flow
A:/# vmstat 5 5 # check that context switches have not inflated too much.
procs -----------memory---------- ---swap-- -----io---- -system-- ------cpu-----
r b swpd free buff cache si so bi bo in cs us sy id wa st
2 0 0 260386512 13592 662148 0 0 10 0 17 14 0 1 99 0 0
0 0 0 260519680 13592 604184 0 0 512 13 726843 12424 0 10 90 0 0
1 1 0 260435424 13592 598360 0 0 512 25 764645 12925 0 10 90 0 0
1 0 0 260855392 13592 578380 0 0 512 7 722943 13624 0 11 88 0 0
1 0 0 260445008 13592 601176 0 0 614 34 772288 14317 0 10 90 0 0
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit dd979b4df8.
This broke tcp_poll for SMC fallback: An AF_SMC socket establishes an
internal TCP socket for the initial handshake with the remote peer.
Whenever the SMC connection can not be established this TCP socket is
used as a fallback. All socket operations on the SMC socket are then
forwarded to the TCP socket. In case of poll, the file->private_data
pointer references the SMC socket because the TCP socket has no file
assigned. This causes tcp_poll to wait on the wrong socket.
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Borkmann says:
====================
pull-request: bpf-next 2018-10-16
The following pull-request contains BPF updates for your *net-next* tree.
The main changes are:
1) Convert BPF sockmap and kTLS to both use a new sk_msg API and enable
sk_msg BPF integration for the latter, from Daniel and John.
2) Enable BPF syscall side to indicate for maps that they do not support
a map lookup operation as opposed to just missing key, from Prashant.
3) Add bpftool map create command which after map creation pins the
map into bpf fs for further processing, from Jakub.
4) Add bpftool support for attaching programs to maps allowing sock_map
and sock_hash to be used from bpftool, from John.
5) Improve syscall BPF map update/delete path for map-in-map types to
wait a RCU grace period for pending references to complete, from Daniel.
6) Couple of follow-up fixes for the BPF socket lookup to get it
enabled also when IPv6 is compiled as a module, from Joe.
7) Fix a generic-XDP bug to handle the case when the Ethernet header
was mangled and thus update skb's protocol and data, from Jesper.
8) Add a missing BTF header length check between header copies from
user space, from Wenwen.
9) Minor fixups in libbpf to use __u32 instead u32 types and include
proper perf_event.h uapi header instead of perf internal one, from Yonghong.
10) Allow to pass user-defined flags through EXTRA_CFLAGS and EXTRA_LDFLAGS
to bpftool's build, from Jiri.
11) BPF kselftest tweaks to add LWTUNNEL to config fragment and to install
with_addr.sh script from flow dissector selftest, from Anders.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
sk_pacing_rate has beed introduced as a u32 field in 2013,
effectively limiting per flow pacing to 34Gbit.
We believe it is time to allow TCP to pace high speed flows
on 64bit hosts, as we now can reach 100Gbit on one TCP flow.
This patch adds no cost for 32bit kernels.
The tcpi_pacing_rate and tcpi_max_pacing_rate were already
exported as 64bit, so iproute2/ss command require no changes.
Unfortunately the SO_MAX_PACING_RATE socket option will stay
32bit and we will need to add a new option to let applications
control high pacing rates.
State Recv-Q Send-Q Local Address:Port Peer Address:Port
ESTAB 0 1787144 10.246.9.76:49992 10.246.9.77:36741
timer:(on,003ms,0) ino:91863 sk:2 <->
skmem:(r0,rb540000,t66440,tb2363904,f605944,w1822984,o0,bl0,d0)
ts sack bbr wscale:8,8 rto:201 rtt:0.057/0.006 mss:1448
rcvmss:536 advmss:1448
cwnd:138 ssthresh:178 bytes_acked:256699822585 segs_out:177279177
segs_in:3916318 data_segs_out:177279175
bbr:(bw:31276.8Mbps,mrtt:0,pacing_gain:1.25,cwnd_gain:2)
send 28045.5Mbps lastrcv:73333
pacing_rate 38705.0Mbps delivery_rate 22997.6Mbps
busy:73333ms unacked:135 retrans:0/157 rcv_space:14480
notsent:2085120 minrtt:0.013
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert kTLS over to make use of sk_msg interface for plaintext and
encrypted scattergather data, so it reuses all the sk_msg helpers
and data structure which later on in a second step enables to glue
this to BPF.
This also allows to remove quite a bit of open coded helpers which
are covered by the sk_msg API. Recent changes in kTLs 80ece6a03a
("tls: Remove redundant vars from tls record structure") and
4e6d47206c ("tls: Add support for inplace records encryption")
changed the data path handling a bit; while we've kept the latter
optimization intact, we had to undo the former change to better
fit the sk_msg model, hence the sg_aead_in and sg_aead_out have
been brought back and are linked into the sk_msg sgs. Now the kTLS
record contains a msg_plaintext and msg_encrypted sk_msg each.
In the original code, the zerocopy_from_iter() has been used out
of TX but also RX path. For the strparser skb-based RX path,
we've left the zerocopy_from_iter() in decrypt_internal() mostly
untouched, meaning it has been moved into tls_setup_from_iter()
with charging logic removed (as not used from RX). Given RX path
is not based on sk_msg objects, we haven't pursued setting up a
dummy sk_msg to call into sk_msg_zerocopy_from_iter(), but it
could be an option to prusue in a later step.
Joint work with John.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
syzkaller was able to hit the WARN_ON(sock_owned_by_user(sk));
in tcp_close()
While a socket is being closed, it is very possible other
threads find it in rtnetlink dump.
tcp_get_info() will acquire the socket lock for a short amount
of time (slow = lock_sock_fast(sk)/unlock_sock_fast(sk, slow);),
enough to trigger the warning.
Fixes: 67db3e4bfb ("tcp: no longer hold ehash lock while calling tcp_get_info()")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch introduces a new sock flag - SOCK_XDP. This will be used
for notifying the upper layer that XDP program is attached on the
lower socket, and requires for extra headroom.
TUN will be the first user.
Signed-off-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We never use RCU protection for it, just a lot of cargo-cult
rcu_deference_protects calls.
Note that we do keep the kfree_rcu call for it, as the references through
struct sock are RCU protected and thus might require a grace period before
freeing.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Acked-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For any open socket file descriptor sock->sk->sk_wq->wait will always
point to sock->wq->wait. That means we can do the shorter dereference
and removal a NULL check and don't have to not worry about any RCU
protection.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The wait_address argument is always directly derived from the filp
argument, so remove it.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Initialize the cookie in one location to reduce code duplication and
avoid bugs from inconsistent initialization, such as that fixed in
commit 9887cba199 ("ip: limit use of gso_size to udp").
Signed-off-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the socket error queue for reporting dropped packets if the
socket has enabled that feature through the SO_TXTIME API.
Packets are dropped either on enqueue() if they aren't accepted by the
qdisc or on dequeue() if the system misses their deadline. Those are
reported as different errors so applications can react accordingly.
Userspace can retrieve the errors through the socket error queue and the
corresponding cmsg interfaces. A struct sock_extended_err* is used for
returning the error data, and the packet's timestamp can be retrieved by
adding both ee_data and ee_info fields as e.g.:
((__u64) serr->ee_data << 32) + serr->ee_info
This feature is disabled by default and must be explicitly enabled by
applications. Enabling it can bring some overhead for the Tx cycles
of the application.
Signed-off-by: Jesus Sanchez-Palencia <jesus.sanchez-palencia@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch introduces SO_TXTIME. User space enables this option in
order to pass a desired future transmit time in a CMSG when calling
sendmsg(2). The argument to this socket option is a 8-bytes long struct
provided by the uapi header net_tstamp.h defined as:
struct sock_txtime {
clockid_t clockid;
u32 flags;
};
Note that new fields were added to struct sock by filling a 2-bytes
hole found in the struct. For that reason, neither the struct size or
number of cachelines were altered.
Signed-off-by: Richard Cochran <rcochran@linutronix.de>
Signed-off-by: Jesus Sanchez-Palencia <jesus.sanchez-palencia@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support to pick Tx queue based on the Rx queue(s) map
configuration set by the admin through the sysfs attribute
for each Tx queue. If the user configuration for receive queue(s) map
does not apply, then the Tx queue selection falls back to CPU(s) map
based selection and finally to hashing.
Signed-off-by: Amritha Nambiar <amritha.nambiar@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds a new field to sock_common 'skc_rx_queue_mapping'
which holds the receive queue number for the connection. The Rx queue
is marked in tcp_finish_connect() to allow a client app to do
SO_INCOMING_NAPI_ID after a connect() call to get the right queue
association for a socket. Rx queue is also marked in tcp_conn_request()
to allow syn-ack to go on the right tx-queue associated with
the queue on which syn is received.
Signed-off-by: Amritha Nambiar <amritha.nambiar@intel.com>
Signed-off-by: Sridhar Samudrala <sridhar.samudrala@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change 'skc_tx_queue_mapping' field in sock_common structure from
'int' to 'unsigned short' type with ~0 indicating unset and
other positive queue values being set. This will accommodate adding
a new 'unsigned short' field in sock_common in the next patch for
rx_queue_mapping.
Signed-off-by: Amritha Nambiar <amritha.nambiar@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking updates from David Miller:
1) Add Maglev hashing scheduler to IPVS, from Inju Song.
2) Lots of new TC subsystem tests from Roman Mashak.
3) Add TCP zero copy receive and fix delayed acks and autotuning with
SO_RCVLOWAT, from Eric Dumazet.
4) Add XDP_REDIRECT support to mlx5 driver, from Jesper Dangaard
Brouer.
5) Add ttl inherit support to vxlan, from Hangbin Liu.
6) Properly separate ipv6 routes into their logically independant
components. fib6_info for the routing table, and fib6_nh for sets of
nexthops, which thus can be shared. From David Ahern.
7) Add bpf_xdp_adjust_tail helper, which can be used to generate ICMP
messages from XDP programs. From Nikita V. Shirokov.
8) Lots of long overdue cleanups to the r8169 driver, from Heiner
Kallweit.
9) Add BTF ("BPF Type Format"), from Martin KaFai Lau.
10) Add traffic condition monitoring to iwlwifi, from Luca Coelho.
11) Plumb extack down into fib_rules, from Roopa Prabhu.
12) Add Flower classifier offload support to igb, from Vinicius Costa
Gomes.
13) Add UDP GSO support, from Willem de Bruijn.
14) Add documentation for eBPF helpers, from Quentin Monnet.
15) Add TLS tx offload to mlx5, from Ilya Lesokhin.
16) Allow applications to be given the number of bytes available to read
on a socket via a control message returned from recvmsg(), from
Soheil Hassas Yeganeh.
17) Add x86_32 eBPF JIT compiler, from Wang YanQing.
18) Add AF_XDP sockets, with zerocopy support infrastructure as well.
From Björn Töpel.
19) Remove indirect load support from all of the BPF JITs and handle
these operations in the verifier by translating them into native BPF
instead. From Daniel Borkmann.
20) Add GRO support to ipv6 gre tunnels, from Eran Ben Elisha.
21) Allow XDP programs to do lookups in the main kernel routing tables
for forwarding. From David Ahern.
22) Allow drivers to store hardware state into an ELF section of kernel
dump vmcore files, and use it in cxgb4. From Rahul Lakkireddy.
23) Various RACK and loss detection improvements in TCP, from Yuchung
Cheng.
24) Add TCP SACK compression, from Eric Dumazet.
25) Add User Mode Helper support and basic bpfilter infrastructure, from
Alexei Starovoitov.
26) Support ports and protocol values in RTM_GETROUTE, from Roopa
Prabhu.
27) Support bulking in ->ndo_xdp_xmit() API, from Jesper Dangaard
Brouer.
28) Add lots of forwarding selftests, from Petr Machata.
29) Add generic network device failover driver, from Sridhar Samudrala.
* ra.kernel.org:/pub/scm/linux/kernel/git/davem/net-next: (1959 commits)
strparser: Add __strp_unpause and use it in ktls.
rxrpc: Fix terminal retransmission connection ID to include the channel
net: hns3: Optimize PF CMDQ interrupt switching process
net: hns3: Fix for VF mailbox receiving unknown message
net: hns3: Fix for VF mailbox cannot receiving PF response
bnx2x: use the right constant
Revert "net: sched: cls: Fix offloading when ingress dev is vxlan"
net: dsa: b53: Fix for brcm tag issue in Cygnus SoC
enic: fix UDP rss bits
netdev-FAQ: clarify DaveM's position for stable backports
rtnetlink: validate attributes in do_setlink()
mlxsw: Add extack messages for port_{un, }split failures
netdevsim: Add extack error message for devlink reload
devlink: Add extack to reload and port_{un, }split operations
net: metrics: add proper netlink validation
ipmr: fix error path when ipmr_new_table fails
ip6mr: only set ip6mr_table from setsockopt when ip6mr_new_table succeeds
net: hns3: remove unused hclgevf_cfg_func_mta_filter
netfilter: provide udp*_lib_lookup for nf_tproxy
qed*: Utilize FW 8.37.2.0
...
No changes in refcount semantics -- key init is false; replace
static_key_slow_inc|dec with static_branch_inc|dec
static_key_false with static_branch_unlikely
Added a '_key' suffix to memalloc_socks, for better self
documentation.
Signed-off-by: Davidlohr Bueso <dbueso@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
With socket dependent offloads we rely on the netdev to transform
the transmitted packets before sending them to the wire.
When a packet from an offloaded socket is rerouted to a different
device we need to detect it and do the transformation in software.
Signed-off-by: Ilya Lesokhin <ilyal@mellanox.com>
Signed-off-by: Boris Pismenny <borisp@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If kmem case sizes are 32-bit, then usecopy region should be too.
Link: http://lkml.kernel.org/r/20180305200730.15812-21-adobriyan@gmail.com
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Cc: David Miller <davem@davemloft.net>
Cc: Christoph Lameter <cl@linux.com>
Cc: Pekka Enberg <penberg@kernel.org>
Cc: David Rientjes <rientjes@google.com>
Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
== The problem ==
See description of the problem in the initial patch of this patch set.
== The solution ==
The patch provides much more reliable in-kernel solution for the 2nd
part of the problem: making outgoing connecttion from desired IP.
It adds new attach types `BPF_CGROUP_INET4_CONNECT` and
`BPF_CGROUP_INET6_CONNECT` for program type
`BPF_PROG_TYPE_CGROUP_SOCK_ADDR` that can be used to override both
source and destination of a connection at connect(2) time.
Local end of connection can be bound to desired IP using newly
introduced BPF-helper `bpf_bind()`. It allows to bind to only IP though,
and doesn't support binding to port, i.e. leverages
`IP_BIND_ADDRESS_NO_PORT` socket option. There are two reasons for this:
* looking for a free port is expensive and can affect performance
significantly;
* there is no use-case for port.
As for remote end (`struct sockaddr *` passed by user), both parts of it
can be overridden, remote IP and remote port. It's useful if an
application inside cgroup wants to connect to another application inside
same cgroup or to itself, but knows nothing about IP assigned to the
cgroup.
Support is added for IPv4 and IPv6, for TCP and UDP.
IPv4 and IPv6 have separate attach types for same reason as sys_bind
hooks, i.e. to prevent reading from / writing to e.g. user_ip6 fields
when user passes sockaddr_in since it'd be out-of-bound.
== Implementation notes ==
The patch introduces new field in `struct proto`: `pre_connect` that is
a pointer to a function with same signature as `connect` but is called
before it. The reason is in some cases BPF hooks should be called way
before control is passed to `sk->sk_prot->connect`. Specifically
`inet_dgram_connect` autobinds socket before calling
`sk->sk_prot->connect` and there is no way to call `bpf_bind()` from
hooks from e.g. `ip4_datagram_connect` or `ip6_datagram_connect` since
it'd cause double-bind. On the other hand `proto.pre_connect` provides a
flexible way to add BPF hooks for connect only for necessary `proto` and
call them at desired time before `connect`. Since `bpf_bind()` is
allowed to bind only to IP and autobind in `inet_dgram_connect` binds
only port there is no chance of double-bind.
bpf_bind() sets `force_bind_address_no_port` to bind to only IP despite
of value of `bind_address_no_port` socket field.
bpf_bind() sets `with_lock` to `false` when calling to __inet_bind()
and __inet6_bind() since all call-sites, where bpf_bind() is called,
already hold socket lock.
Signed-off-by: Andrey Ignatov <rdna@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Add support for the BPF_F_INGRESS flag in sk_msg redirect helper.
To do this add a scatterlist ring for receiving socks to check
before calling into regular recvmsg call path. Additionally, because
the poll wakeup logic only checked the skb recv queue we need to
add a hook in TCP stack (similar to write side) so that we have
a way to wake up polling socks when a scatterlist is redirected
to that sock.
After this all that is needed is for the redirect helper to
push the scatterlist into the psock receive queue.
Signed-off-by: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Fun set of conflict resolutions here...
For the mac80211 stuff, these were fortunately just parallel
adds. Trivially resolved.
In drivers/net/phy/phy.c we had a bug fix in 'net' that moved the
function phy_disable_interrupts() earlier in the file, whilst in
'net-next' the phy_error() call from this function was removed.
In net/ipv4/xfrm4_policy.c, David Ahern's changes to remove the
'rt_table_id' member of rtable collided with a bug fix in 'net' that
added a new struct member "rt_mtu_locked" which needs to be copied
over here.
The mlxsw driver conflict consisted of net-next separating
the span code and definitions into separate files, whilst
a 'net' bug fix made some changes to that moved code.
The mlx5 infiniband conflict resolution was quite non-trivial,
the RDMA tree's merge commit was used as a guide here, and
here are their notes:
====================
Due to bug fixes found by the syzkaller bot and taken into the for-rc
branch after development for the 4.17 merge window had already started
being taken into the for-next branch, there were fairly non-trivial
merge issues that would need to be resolved between the for-rc branch
and the for-next branch. This merge resolves those conflicts and
provides a unified base upon which ongoing development for 4.17 can
be based.
Conflicts:
drivers/infiniband/hw/mlx5/main.c - Commit 42cea83f95
(IB/mlx5: Fix cleanup order on unload) added to for-rc and
commit b5ca15ad7e (IB/mlx5: Add proper representors support)
add as part of the devel cycle both needed to modify the
init/de-init functions used by mlx5. To support the new
representors, the new functions added by the cleanup patch
needed to be made non-static, and the init/de-init list
added by the representors patch needed to be modified to
match the init/de-init list changes made by the cleanup
patch.
Updates:
drivers/infiniband/hw/mlx5/mlx5_ib.h - Update function
prototypes added by representors patch to reflect new function
names as changed by cleanup patch
drivers/infiniband/hw/mlx5/ib_rep.c - Update init/de-init
stage list to match new order from cleanup patch
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The current implementation of sk_alloc_sg expects scatterlist to always
start at entry 0 and complete at entry MAX_SKB_FRAGS.
Future patches will want to support starting at arbitrary offset into
scatterlist so add an additional sg_start parameters and then default
to the current values in TLS code paths.
Signed-off-by: John Fastabend <john.fastabend@gmail.com>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
The TLS ULP module builds scatterlists from a sock using
page_frag_refill(). This is going to be useful for other ULPs
so move it into sock file for more general use.
In the process remove useless goto at end of while loop.
Signed-off-by: John Fastabend <john.fastabend@gmail.com>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Now when using 'ss' in iproute, kernel would try to load all _diag
modules, which also causes corresponding family and proto modules
to be loaded as well due to module dependencies.
Like after running 'ss', sctp, dccp, af_packet (if it works as a module)
would be loaded.
For example:
$ lsmod|grep sctp
$ ss
$ lsmod|grep sctp
sctp_diag 16384 0
sctp 323584 5 sctp_diag
inet_diag 24576 4 raw_diag,tcp_diag,sctp_diag,udp_diag
libcrc32c 16384 3 nf_conntrack,nf_nat,sctp
As these family and proto modules are loaded unintentionally, it
could cause some problems, like:
- Some debug tools use 'ss' to collect the socket info, which loads all
those diag and family and protocol modules. It's noisy for identifying
issues.
- Users usually expect to drop sctp init packet silently when they
have no sense of sctp protocol instead of sending abort back.
- It wastes resources (especially with multiple netns), and SCTP module
can't be unloaded once it's loaded.
...
In short, it's really inappropriate to have these family and proto
modules loaded unexpectedly when just doing debugging with inet_diag.
This patch is to introduce sock_load_diag_module() where it loads
the _diag module only when it's corresponding family or proto has
been already registered.
Note that we can't just load _diag module without the family or
proto loaded, as some symbols used in _diag module are from the
family or proto module.
v1->v2:
- move inet proto check to inet_diag to avoid a compiling err.
v2->v3:
- define sock_load_diag_module in sock.c and export one symbol
only.
- improve the changelog.
Reported-by: Sabrina Dubroca <sd@queasysnail.net>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Acked-by: Phil Sutter <phil@nwl.cc>
Acked-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since TCP relies on GSO, we do not need this helper anymore.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jakub Kicinski
Al Viro
Eric Dumazet
Thomas Gleixner
Martin KaFai Lau
Arnd Bergmann
David S. Miller
Ursula Braun
Maxime Chevallier
Deepa Dinamani
Willem de Bruijn
Karsten Graul
Daniel Borkmann
Jason Wang
Christoph Hellwig
Jesus Sanchez-Palencia
Richard Cochran
Amritha Nambiar
Linus Torvalds
Davidlohr Bueso
Ilya Lesokhin
Alexey Dobriyan
Andrey Ignatov
John Fastabend
Xin Long