Use devres to allocate the dedicated deferred_tx_wq polling workqueue so
as to automatically trigger the proper resource release on error path.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Fixes: 5a3b7185c4 ("firmware: arm_scmi: Add atomic mode support to virtio transport")
Signed-off-by: Cristian Marussi <cristian.marussi@arm.com>
Link: https://lore.kernel.org/r/20221028140833.280091-6-cristian.marussi@arm.com
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
SCMI virtio transport device managed allocations must use the main
platform device in devres operations instead of the channel devices.
Cc: Peter Hilber <peter.hilber@opensynergy.com>
Fixes: 46abe13b5e ("firmware: arm_scmi: Add virtio transport")
Signed-off-by: Cristian Marussi <cristian.marussi@arm.com>
Link: https://lore.kernel.org/r/20221028140833.280091-5-cristian.marussi@arm.com
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
SCMI Rx channels are optional and they can fail to be setup when not
present but anyway channels setup routines must bail-out on memory errors.
Make channels setup, and related probing, fail when memory errors are
reported on Rx channels.
Fixes: 5c8a47a5a9 ("firmware: arm_scmi: Make scmi core independent of the transport type")
Signed-off-by: Cristian Marussi <cristian.marussi@arm.com>
Link: https://lore.kernel.org/r/20221028140833.280091-4-cristian.marussi@arm.com
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
SCMI transports based on shared memory, at start of transmissions, have
to wait for the shared Tx channel area to be eventually freed by the
SCMI platform before accessing the channel. In fact the channel is owned
by the SCMI platform until marked as free by the platform itself and,
as such, cannot be used by the agent until relinquished.
As a consequence a badly misbehaving SCMI platform firmware could lock
the channel indefinitely and make the kernel side SCMI stack loop
forever waiting for such channel to be freed, possibly hanging the
whole boot sequence.
Add a timeout to the existent Tx waiting spin-loop so that, when the
system ends up in this situation, the SCMI stack can at least bail-out,
nosily warn the user, and abort the transmission.
Reported-by: YaxiongTian <iambestgod@outlook.com>
Suggested-by: YaxiongTian <iambestgod@outlook.com>
Cc: Vincent Guittot <vincent.guittot@linaro.org>
Cc: Etienne Carriere <etienne.carriere@linaro.org>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Cristian Marussi <cristian.marussi@arm.com>
Link: https://lore.kernel.org/r/20221028140833.280091-3-cristian.marussi@arm.com
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Suppress the capability to unbind the core SCMI driver since all the
SCMI stack protocol drivers depend on it.
Fixes: aa4f886f38 ("firmware: arm_scmi: add basic driver infrastructure for SCMI")
Signed-off-by: Cristian Marussi <cristian.marussi@arm.com>
Link: https://lore.kernel.org/r/20221028140833.280091-2-cristian.marussi@arm.com
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Platform drivers .remove callbacks are not supposed to fail and report
errors. Such errors are indeed ignored by the core platform drivers
and the driver unbind process is anyway completed.
The SCMI core platform driver as it is now, instead, bails out reporting
an error in case of an explicit unbind request.
Fix the removal path by adding proper device links between the core SCMI
device and the SCMI protocol devices so that a full SCMI stack unbind is
triggered when the core driver is removed. The remove process does not
bail out anymore on the anomalous conditions triggered by an explicit
unbind but the user is still warned.
Reported-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Cristian Marussi <cristian.marussi@arm.com>
Link: https://lore.kernel.org/r/20221028140833.280091-1-cristian.marussi@arm.com
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
- Terminate infinite loop in SD-UHS voltage switch
MMC host:
- hsq: Fix kernel crash in the recovery path
- moxart: Fix bus width configurations
- sdhci: Fix kernel panic for cqe irq
ARM_SCMI:
- Fixup clock management by reverting "firmware: arm_scmi: Add clock
management to the SCMI power domain"
-----BEGIN PGP SIGNATURE-----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=F5JH
-----END PGP SIGNATURE-----
Merge tag 'mmc-v6.0-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc
Pull MMC fixes from Ulf Hansson:
"A couple of MMC fixes. This time there is also a fix for the ARM SCMI
firmware driver, which has been acked by Sudeep Holla, the maintainer.
MMC core:
- Terminate infinite loop in SD-UHS voltage switch
MMC host:
- hsq: Fix kernel crash in the recovery path
- moxart: Fix bus width configurations
- sdhci: Fix kernel panic for cqe irq
ARM_SCMI:
- Fixup clock management by reverting 'firmware: arm_scmi: Add clock
management to the SCMI power domain'"
* tag 'mmc-v6.0-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc:
mmc: hsq: Fix data stomping during mmc recovery
Revert "firmware: arm_scmi: Add clock management to the SCMI power domain"
mmc: core: Terminate infinite loop in SD-UHS voltage switch
mmc: moxart: fix 4-bit bus width and remove 8-bit bus width
mmc: sdhci: Fix host->cmd is null
This reverts commit a3b884cef8 ("firmware: arm_scmi: Add clock management
to the SCMI power domain").
Using the GENPD_FLAG_PM_CLK tells genpd to gate/ungate the consumer
device's clock(s) during runtime suspend/resume through the PM clock API.
More precisely, in genpd_runtime_resume() the clock(s) for the consumer
device would become ungated prior to the driver-level ->runtime_resume()
callbacks gets invoked.
This behaviour isn't a good fit for all platforms/drivers. For example, a
driver may need to make some preparations of its device in its
->runtime_resume() callback, like calling clk_set_rate() before the
clock(s) should be ungated. In these cases, it's easier to let the clock(s)
to be managed solely by the driver, rather than at the PM domain level.
For these reasons, let's drop the use GENPD_FLAG_PM_CLK for the SCMI PM
domain, as to enable it to be more easily adopted across ARM platforms.
Fixes: a3b884cef8 ("firmware: arm_scmi: Add clock management to the SCMI power domain")
Cc: Nicolas Pitre <npitre@baylibre.com>
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Peng Fan <peng.fan@nxp.com>
Acked-by: Sudeep Holla <sudeep.holla@arm.com>
Link: https://lore.kernel.org/r/20220919122033.86126-1-ulf.hansson@linaro.org
Currently, when removing the SCMI PM driver not all the resources
registered with genpd subsystem are properly de-registered.
As a side effect of this after a driver unload/load cycle you get a
splat with a few warnings like this:
| debugfs: Directory 'BIG_CPU0' with parent 'pm_genpd' already present!
| debugfs: Directory 'BIG_CPU1' with parent 'pm_genpd' already present!
| debugfs: Directory 'LITTLE_CPU0' with parent 'pm_genpd' already present!
| debugfs: Directory 'LITTLE_CPU1' with parent 'pm_genpd' already present!
| debugfs: Directory 'LITTLE_CPU2' with parent 'pm_genpd' already present!
| debugfs: Directory 'LITTLE_CPU3' with parent 'pm_genpd' already present!
| debugfs: Directory 'BIG_SSTOP' with parent 'pm_genpd' already present!
| debugfs: Directory 'LITTLE_SSTOP' with parent 'pm_genpd' already present!
| debugfs: Directory 'DBGSYS' with parent 'pm_genpd' already present!
| debugfs: Directory 'GPUTOP' with parent 'pm_genpd' already present!
Add a proper scmi_pm_domain_remove callback to the driver in order to
take care of all the needed cleanups not handled by devres framework.
Link: https://lore.kernel.org/r/20220817172731.1185305-7-cristian.marussi@arm.com
Signed-off-by: Cristian Marussi <cristian.marussi@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
SCMI Reset protocol specification allows the asynchronous reset request
only when an autonomous reset action is specified. Reset requests based
on explicit assert/deassert of signals should not be served
asynchronously.
Current implementation will instead issue an asynchronous request in any
case, as long as the reset domain had advertised to support asynchronous
resets.
Avoid requesting the asynchronous resets when the reset action is not
of the autonomous type, even if the target reset domain does, in general,
support the asynchronous requests.
Link: https://lore.kernel.org/r/20220817172731.1185305-6-cristian.marussi@arm.com
Fixes: 95a15d80aa ("firmware: arm_scmi: Add RESET protocol in SCMI v2.0")
Signed-off-by: Cristian Marussi <cristian.marussi@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Accessing reset domains descriptors by the index upon the SCMI drivers
requests through the SCMI reset operations interface can potentially
lead to out-of-bound violations if the SCMI driver misbehave.
Add an internal consistency check before any such domains descriptors
accesses.
Link: https://lore.kernel.org/r/20220817172731.1185305-5-cristian.marussi@arm.com
Signed-off-by: Cristian Marussi <cristian.marussi@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Accessing sensor domains descriptors by the index upon the SCMI drivers
requests through the SCMI sensor operations interface can potentially
lead to out-of-bound violations if the SCMI driver misbehave.
Add an internal consistency check before any such domains descriptors
accesses.
Link: https://lore.kernel.org/r/20220817172731.1185305-4-cristian.marussi@arm.com
Signed-off-by: Cristian Marussi <cristian.marussi@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
SCMI protocols abstract and expose a number of protocol specific
resources like clocks, sensors and so on. Information about such
specific domain resources are generally exposed via an `info_get`
protocol operation.
Improve the sanity check on these operations where needed.
Link: https://lore.kernel.org/r/20220817172731.1185305-3-cristian.marussi@arm.com
Signed-off-by: Cristian Marussi <cristian.marussi@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
- Make cpufreq_show_cpus() more straightforward (Viresh Kumar).
- Drop unnecessary CPU hotplug locking from store() used by cpufreq
sysfs attributes (Viresh Kumar).
- Make the ACPI cpufreq driver support the boost control interface on
Zhaoxin/Centaur processors (Tony W Wang-oc).
- Print a warning message on attempts to free an active cpufreq policy
which should never happen (Viresh Kumar).
- Fix grammar in the Kconfig help text for the loongson2 cpufreq
driver (Randy Dunlap).
- Use cpumask_var_t for an on-stack CPU mask in the ondemand cpufreq
governor (Zhao Liu).
- Add trace points for guest_halt_poll_ns grow/shrink to the haltpoll
cpuidle driver (Eiichi Tsukata).
- Modify intel_idle to treat C1 and C1E as independent idle states on
Sapphire Rapids (Artem Bityutskiy).
- Extend support for wakeirq to callback wrappers used during system
suspend and resume (Ulf Hansson).
- Defer waiting for device probe before loading a hibernation image
till the first actual device access to avoid possible deadlocks
reported by syzbot (Tetsuo Handa).
- Unify device_init_wakeup() for PM_SLEEP and !PM_SLEEP (Bjorn
Helgaas).
- Add Raptor Lake-P to the list of processors supported by the Intel
RAPL driver (George D Sworo).
- Add Alder Lake-N and Raptor Lake-P to the list of processors for
which Power Limit4 is supported in the Intel RAPL driver (Sumeet
Pawnikar).
- Make pm_genpd_remove() check genpd_debugfs_dir against NULL before
attempting to remove it (Hsin-Yi Wang).
- Change the Energy Model code to represent power in micro-Watts and
adjust its users accordingly (Lukasz Luba).
- Add new devfreq driver for Mediatek CCI (Cache Coherent
Interconnect) (Johnson Wang).
- Convert the Samsung Exynos SoC Bus bindings to DT schema of
exynos-bus.c (Krzysztof Kozlowski).
- Address kernel-doc warnings by adding the description for unused
fucntion parameters in devfreq core (Mauro Carvalho Chehab).
- Use NULL to pass a null pointer rather than zero according to the
function propotype in imx-bus.c (Colin Ian King).
- Print error message instead of error interger value in
tegra30-devfreq.c (Dmitry Osipenko).
- Add checks to prevent setting negative frequency QoS limits for
CPUs (Shivnandan Kumar).
- Update the pm-graph suite of utilities to the latest revision 5.9
including multiple improvements (Todd Brandt).
- Drop pme_interrupt reference from the PCI power management
documentation (Mario Limonciello).
-----BEGIN PGP SIGNATURE-----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=XeLV
-----END PGP SIGNATURE-----
Merge tag 'pm-5.20-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management updates from Rafael Wysocki:
"These are mostly minor improvements all over including new CPU IDs for
the Intel RAPL driver, an Energy Model rework to use micro-Watt as the
power unit, cpufreq fixes and cleanus, cpuidle updates, devfreq
updates, documentation cleanups and a new version of the pm-graph
suite of utilities.
Specifics:
- Make cpufreq_show_cpus() more straightforward (Viresh Kumar).
- Drop unnecessary CPU hotplug locking from store() used by cpufreq
sysfs attributes (Viresh Kumar).
- Make the ACPI cpufreq driver support the boost control interface on
Zhaoxin/Centaur processors (Tony W Wang-oc).
- Print a warning message on attempts to free an active cpufreq
policy which should never happen (Viresh Kumar).
- Fix grammar in the Kconfig help text for the loongson2 cpufreq
driver (Randy Dunlap).
- Use cpumask_var_t for an on-stack CPU mask in the ondemand cpufreq
governor (Zhao Liu).
- Add trace points for guest_halt_poll_ns grow/shrink to the haltpoll
cpuidle driver (Eiichi Tsukata).
- Modify intel_idle to treat C1 and C1E as independent idle states on
Sapphire Rapids (Artem Bityutskiy).
- Extend support for wakeirq to callback wrappers used during system
suspend and resume (Ulf Hansson).
- Defer waiting for device probe before loading a hibernation image
till the first actual device access to avoid possible deadlocks
reported by syzbot (Tetsuo Handa).
- Unify device_init_wakeup() for PM_SLEEP and !PM_SLEEP (Bjorn
Helgaas).
- Add Raptor Lake-P to the list of processors supported by the Intel
RAPL driver (George D Sworo).
- Add Alder Lake-N and Raptor Lake-P to the list of processors for
which Power Limit4 is supported in the Intel RAPL driver (Sumeet
Pawnikar).
- Make pm_genpd_remove() check genpd_debugfs_dir against NULL before
attempting to remove it (Hsin-Yi Wang).
- Change the Energy Model code to represent power in micro-Watts and
adjust its users accordingly (Lukasz Luba).
- Add new devfreq driver for Mediatek CCI (Cache Coherent
Interconnect) (Johnson Wang).
- Convert the Samsung Exynos SoC Bus bindings to DT schema of
exynos-bus.c (Krzysztof Kozlowski).
- Address kernel-doc warnings by adding the description for unused
function parameters in devfreq core (Mauro Carvalho Chehab).
- Use NULL to pass a null pointer rather than zero according to the
function propotype in imx-bus.c (Colin Ian King).
- Print error message instead of error interger value in
tegra30-devfreq.c (Dmitry Osipenko).
- Add checks to prevent setting negative frequency QoS limits for
CPUs (Shivnandan Kumar).
- Update the pm-graph suite of utilities to the latest revision 5.9
including multiple improvements (Todd Brandt).
- Drop pme_interrupt reference from the PCI power management
documentation (Mario Limonciello)"
* tag 'pm-5.20-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (27 commits)
powercap: RAPL: Add Power Limit4 support for Alder Lake-N and Raptor Lake-P
PM: QoS: Add check to make sure CPU freq is non-negative
PM: hibernate: defer device probing when resuming from hibernation
intel_idle: make SPR C1 and C1E be independent
cpufreq: ondemand: Use cpumask_var_t for on-stack cpu mask
cpufreq: loongson2: fix Kconfig "its" grammar
pm-graph v5.9
cpufreq: Warn users while freeing active policy
cpufreq: scmi: Support the power scale in micro-Watts in SCMI v3.1
firmware: arm_scmi: Get detailed power scale from perf
Documentation: EM: Switch to micro-Watts scale
PM: EM: convert power field to micro-Watts precision and align drivers
PM / devfreq: tegra30: Add error message for devm_devfreq_add_device()
PM / devfreq: imx-bus: use NULL to pass a null pointer rather than zero
PM / devfreq: shut up kernel-doc warnings
dt-bindings: interconnect: samsung,exynos-bus: convert to dtschema
PM / devfreq: mediatek: Introduce MediaTek CCI devfreq driver
dt-bindings: interconnect: Add MediaTek CCI dt-bindings
PM: domains: Ensure genpd_debugfs_dir exists before remove
PM: runtime: Extend support for wakeirq for force_suspend|resume
...
In SCMI v3.1 the power scale can be in micro-Watts. The upper layers, e.g.
cpufreq and EM should handle received power values properly (upscale when
needed). Thus, provide an interface which allows to check what is the
scale for power values. The old interface allowed to distinguish between
bogo-Watts and milli-Watts only (which was good for older SCMI spec).
Acked-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Lukasz Luba <lukasz.luba@arm.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Add SCMIv3.1 powercap protocol fast channel support using common helpers
provided by the SCMI core with scmi_proto_helpers_ops operations.
Link: https://lore.kernel.org/r/20220704102241.2988447-5-cristian.marussi@arm.com
Signed-off-by: Cristian Marussi <cristian.marussi@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Generalize existing fast channel support used in the perf protocol and
make it available to possibly any protocol refactoring the common code
into a couple of new scmi_proto_helpers_ops routines.
Make perf protocol use this new infrastructure.
No functional change.
Link: https://lore.kernel.org/r/20220704102241.2988447-4-cristian.marussi@arm.com
Signed-off-by: Cristian Marussi <cristian.marussi@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Add support for SCMI v3.1 powercap protocol, with the exception of powercap
fast channels, exposing all the new related powercap protocol operations as
usual in include/linux/scmi_protocol.h.
Link: https://lore.kernel.org/r/20220704102241.2988447-3-cristian.marussi@arm.com
Signed-off-by: Cristian Marussi <cristian.marussi@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Add an SCMI System Power control driver to handle platform's requests
carried by SYSTEM_POWER_STATE_NOTIFIER notifications: such platform
requested system-wide power state transitions are handled accordingly,
gracefully or forcefully, depending on the notifications' message flags.
Graceful requests are relayed to userspace using the same Kernel API used
to handle ACPI Shutdown bus events.
Link: https://lore.kernel.org/r/20220704101933.2981635-5-cristian.marussi@arm.com
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Cristian Marussi <cristian.marussi@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Add a method to get hold of a protocol, causing it to be initialized and
its resource accounting updated, without getting access to its operations
and handle.
Some protocols, like SCMI SystemPower, do not expose any protocol ops to
the kernel OSPM agent but still need to be at least initialized. This
helper avoids the need to invoke a full devm_get_protocol() only to get
the protocol initialized while throwing away unused the protocol ops and
handle.
Link: https://lore.kernel.org/r/20220704101933.2981635-4-cristian.marussi@arm.com
Signed-off-by: Cristian Marussi <cristian.marussi@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Add support for SCMIv3.1 System Power optional timeout field while
dispatching SYSTEM_POWER_STATE_NOTIFIER notification.
Link: https://lore.kernel.org/r/20220704101933.2981635-3-cristian.marussi@arm.com
Signed-off-by: Cristian Marussi <cristian.marussi@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
In order to minimize SCMI platform fw-side complexity, only one single SCMI
platform should be in charge of SCMI SystemPower protocol communications
with the OSPM. Enforce the existence of one single unique device associated
with SystemPower protocol across any possible number of SCMI platforms, and
warn if a system tries to register different SystemPower devices from
multiple platforms.
Link: https://lore.kernel.org/r/20220704101933.2981635-2-cristian.marussi@arm.com
Signed-off-by: Cristian Marussi <cristian.marussi@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Add full message tracing for all transmitted and successfully received SCMI
commands, replies and notifications.
Link: https://lore.kernel.org/r/20220630173135.2086631-3-cristian.marussi@arm.com
Signed-off-by: Cristian Marussi <cristian.marussi@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Replace the deprecated ida_simple_{get,remove} with ida_{alloc,free}.
Link: https://lore.kernel.org/r/20220616055052.4559-1-liubo03@inspur.com
Signed-off-by: Bo Liu <liubo03@inspur.com>
[sudeep.holla: Replace ida_alloc_min with ida_alloc as suggested by Cristian]
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Some protocols check the response size with the expected value but optee
shared memory doesn't return such size whereas it is available in the
optee output buffer.
As an example, the base protocol compares the response size with the
expected result when requesting the list of protocol which triggers a
warning with optee shared memory:
arm-scmi firmware:scmi0: Malformed reply - real_sz:116 calc_sz:4 (loop_num_ret:4)
Save the output buffer length and use it when fetching the answer.
Link: https://lore.kernel.org/r/20220624074549.3298-1-vincent.guittot@linaro.org
Reviewed-by: Etienne Carriere <etienne.carriere@linaro.org>
Reviewed-by: Cristian Marussi <cristian.marussi@arm.com>
Signed-off-by: Vincent Guittot <vincent.guittot@linaro.org>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
A reply to CLOCK_DESCRIBE_RATES issued against a non rate-discrete clock
should be composed of a triplet of rates descriptors (min/max/step)
returned all in one reply message.
This is not always the case when dealing with some SCMI server deployed in
the wild: relax such constraint while maintaining memory safety by checking
carefully the returned payload size.
While at that cleanup a stale debug printout.
Link: https://lore.kernel.org/r/20220616170347.2800771-1-cristian.marussi@arm.com
Fixes: 7bc7caafe6 ("firmware: arm_scmi: Use common iterators in the clock protocol")
Tested-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Cristian Marussi <cristian.marussi@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
scmi_voltage_descriptors_get() will incorrecly return an error code if
the last iteration of the for loop that retrieves the descriptors is
skipped due to an error. Skipping an iteration in the loop is not an
error, but the `ret` value from the last iteration will be propagated
when the function returns.
Fix by not saving return values that should not be propagated. This
solution also minimizes the risk of future patches accidentally
re-introducing this bug.
Link: https://lore.kernel.org/r/20220610140055.31491-1-ludvig.parsson@axis.com
Reviewed-by: Cristian Marussi <cristian.marussi@arm.com>
Signed-off-by: Ludvig Pärsson <ludvig.parsson@axis.com>
[sudeep.holla: Removed unneeded reset_rx_to_maxsz and check for return
value from scmi_voltage_levels_get as suggested by Cristian]
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Commit b260fccaeb ("firmware: arm_scmi: Add SCMI v3.1 protocol extended
names support") moved all the name string buffers to use the extended buffer
size of 64 instead of the required 16 bytes. While that should be fine if
the firmware terminates the string before 16 bytes, there is possibility
of copying random data if the name is not NULL terminated by the firmware.
SCMI base protocol agent_name/vendor_id/sub_vendor_id are defined by the
specification as NULL-terminated ASCII strings up to 16-bytes in length.
The underlying buffers and message descriptors are currently bigger than
needed; resize them to fit only the strictly needed 16 bytes to avoid
any possible leaks when reading data from the firmware.
Change the size argument of strlcpy to use SCMI_SHORT_NAME_MAX_SIZE always
when dealing with short domain names, so as to limit the possibility that
an ill-formed non-NULL terminated short reply from the SCMI platform
firmware can leak stale content laying in the underlying transport shared
memory area.
While at that, convert all strings handling routines to use the preferred
strscpy.
Link: https://lore.kernel.org/r/20220608095530.497879-1-cristian.marussi@arm.com
Fixes: b260fccaeb ("firmware: arm_scmi: Add SCMI v3.1 protocol extended names support")
Signed-off-by: Cristian Marussi <cristian.marussi@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Avoid to invoke SENSOR_AXIS_NAME_GET on sensors that have not declared at
least one of their axes as supporting extended names.
Since the returned list of axes supporting extended names is not
necessarily comprising all the existing axes of the specified sensor,
take care also to properly pick the axis descriptor from the ID embedded
in the response.
Link: https://lore.kernel.org/r/20220608164051.2326087-1-cristian.marussi@arm.com
Fixes: 802b0bed01 ("firmware: arm_scmi: Add SCMI v3.1 SENSOR_AXIS_NAME_GET support")
Cc: Peter Hilber <peter.hilber@opensynergy.com>
Cc: Sudeep Holla <sudeep.holla@arm.com>
Reviewed-by: Peter Hilber <peter.hilber@opensynergy.com>
Signed-off-by: Cristian Marussi <cristian.marussi@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
While using SCMI iterators helpers a few local automatic variables are
defined but then used only as input for sizeof operators.
cppcheck is fooled to complain about this with:
| drivers/firmware/arm_scmi/sensors.c:341:48: warning: Variable 'msg' is
| not assigned a value. [unassignedVariable]
| struct scmi_msg_sensor_list_update_intervals *msg;
Even though this is an innocuos warning, since the uninitialized variable
is at the end never used in the reported cases, fix these occurences all
over SCMI stack to avoid keeping unneeded objects on the stack.
Link: https://lore.kernel.org/r/20220530115237.277077-1-cristian.marussi@arm.com
Cc: Dan Carpenter <dan.carpenter@oracle.com>
Cc: Sudeep Holla <sudeep.holla@arm.com>
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Cristian Marussi <cristian.marussi@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Even though malformed replies from firmware must be treated carefully to
avoid memory corruption in the kernel, some out-of-spec SCMI replies can
be tolerated to avoid breaking existing deployed system, as long as they
won't cause memory issues.
Relax the sanity checks on the recieved protocol list in the base protocol
to avoid breaking one of the deployed platform whose firmware is not easily
upgradable currently.
Link: https://lore.kernel.org/r/20220523171559.472112-1-cristian.marussi@arm.com
Cc: Etienne Carriere <etienne.carriere@linaro.org>
Cc: Sudeep Holla <sudeep.holla@arm.com>
Reported-by: Nicolas Frattaroli <frattaroli.nicolas@gmail.com>
Tested-By: Frank Wunderlich <frank-w@public-files.de>
Acked-by: Michael Riesch <michael.riesch@wolfvision.net>
Acked-by: Etienne Carriere <etienne.carriere@linaro.org>
Signed-off-by: Cristian Marussi <cristian.marussi@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
A few dereferences could happen before the iterator pointer argument was
checked for NULL, causing the following smatch warnings:
drivers/firmware/arm_scmi/driver.c:1214 scmi_iterator_run() warn: variable
dereferenced before check 'i' (see line 1210)
Fix by moving the checks early and dropping some unneeded local references.
No functional change.
Link: https://lore.kernel.org/r/20220503121047.3590340-1-cristian.marussi@arm.com
Reported-by: kernel test robot <lkp@intel.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Cristian Marussi <cristian.marussi@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Add support for TEE shared memory in optee scmi transport. When using
tee shared memory, scmi optee transport manages SCMI messages using
msg protocol(from msg.c) in shared memory, whereas smt(from shmem.c)
protocol is used with static IOMEM based shared buffers.
Link: https://lore.kernel.org/r/20220425085127.2009-1-etienne.carriere@linaro.org
Reviewed-by: Cristian Marussi <cristian.marussi@arm.com>
Signed-off-by: Etienne Carriere <etienne.carriere@linaro.org>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Add SCMI v3.1 voltage protocol support for asynchronous VOLTAGE_LEVEL_SET
command.
Note that, if a voltage domain is advertised to support the asynchronous
version of VOLTAGE_LEVEL_SET, the command will be issued asynchronously
unless explicitly requested to use the synchronous version by setting the
mode to SCMI_VOLTAGE_LEVEL_SET_SYNC when calling voltage_ops->level_set.
The SCMI regulator driver level_set invocation has been left unchanged
so that it will transparently use the asynchronous version if available.
Link: https://lore.kernel.org/r/20220330150551.2573938-21-cristian.marussi@arm.com
Signed-off-by: Cristian Marussi <cristian.marussi@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Starting with SCMI v3.1, the PERFORMANCE_LIMITS_SET command allows a user
to request only one between max and min ranges to be changed, while leaving
the other untouched if set to zero in the request. Anyway SCMI v3.1 states
also explicitly that you cannot leave both of those unchanged (zeroed) when
issuing such command, so add a proper check for this condition.
Link: https://lore.kernel.org/r/20220330150551.2573938-23-cristian.marussi@arm.com
Signed-off-by: Cristian Marussi <cristian.marussi@arm.com>
[sudeep.holla: Dropped check for v3.0 and above to make the check
unconditional, updated the subject accordingly]
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Add SCMI v3.1 internal support for parsing message attributes reporting
the capability of a performance domain to report power-cost in microwatts.
Link: https://lore.kernel.org/r/20220330150551.2573938-22-cristian.marussi@arm.com
Cc: Lukasz Luba <lukasz.luba@arm.com>
Reviewed-by: Lukasz Luba <lukasz.luba@arm.com>
Signed-off-by: Cristian Marussi <cristian.marussi@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
SCMI specification defines some commands as optionally issued over multiple
messages in order to overcome possible limitations in payload size enforced
by the configured underlyinng transport.
Introduce some common protocol helpers to provide a unified solution for
issuing such SCMI multi-part commands.
Link: https://lore.kernel.org/r/20220330150551.2573938-14-cristian.marussi@arm.com
Signed-off-by: Cristian Marussi <cristian.marussi@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
The clock_enable_latency field in CLOCK_ATTRIBUTES response message has
been added only since SCMI v3.1. Use the advertised SCMI clock protocol
version as a proper condition check for parsing it, instead of the bare
message length lookup.
Link: https://lore.kernel.org/r/20220330150551.2573938-13-cristian.marussi@arm.com
Signed-off-by: Cristian Marussi <cristian.marussi@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
As per the spec, the clock_enable_delay is the worst case latency
incurred by the platform to enable the clock. The value of 0 indicates
that the platform doesn't support the same and must be considered as
maximum latency for practical purposes.
Currently the value of 0 is assigned as is and is propogated to the clock
framework which can assume that the clock can support atomic enable operation.
Link: https://lore.kernel.org/r/20220428122913.1654821-1-sudeep.holla@arm.com
Fixes: 18f295b758 ("firmware: arm_scmi: Add support for clock_enable_latency")
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Using the common protocol helper implementation add support for all new
SCMIv3.1 extended names commands related to all protocols with the
exception of SENSOR_AXIS_GET_NAME.
Link: https://lore.kernel.org/r/20220330150551.2573938-12-cristian.marussi@arm.com
Signed-off-by: Cristian Marussi <cristian.marussi@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Introduce a new set of common protocol operations bound to the protocol
handle structure so that can be invoked by the protocol implementation code
even when protocols are built as distinct loadable kernel module without
the need of exporting new symbols, like already done with scmi_xfer_ops.
Add at first, as new common protocol helper, an .extended_name_get helper
which will ease implementation and will avoid code duplication when adding
new SCMIv3.1 per-protocol _NAME_GET commands.
Link: https://lore.kernel.org/r/20220330150551.2573938-11-cristian.marussi@arm.com
Signed-off-by: Cristian Marussi <cristian.marussi@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Move some SCMI protocol specific definitions from common.h into a the new
dedicated protocols.h header so that SCMI protocols core code can include
only what it needs; this is going to be useful to avoid the risk of growing
indefinitely the dimension of common.h, especially when introducing some
common protocols helper functions.
Header common.h will continue to be included by SCMI core and transport
layers.
Link: https://lore.kernel.org/r/20220330150551.2573938-10-cristian.marussi@arm.com
Signed-off-by: Cristian Marussi <cristian.marussi@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Cristian Marussi
Linus Torvalds
Ulf Hansson
Lukasz Luba
Bo Liu
Vincent Guittot
Ludvig Pärsson
Etienne Carriere
Sudeep Holla