Add option to start DMA component after DAI trigger. This is done
by filling the new struct snd_soc_component_driver::start_dma_last.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Link: https://lore.kernel.org/r/20230228110145.3770525-2-claudiu.beznea@microchip.com
Signed-off-by: Mark Brown <broonie@kernel.org>
When we fail to obtain a DMA channel, don't return a blanket -EINVAL,
instead return the original error code if there's one. This makes
deferring work as it should. Also don't print an error message for
-EPROBE_DEFER.
Fixes: 4ec8179c21 ("ASoC: apple: mca: Postpone requesting of DMA channels")
Signed-off-by: Martin Povišer <povik+lin@cutebit.org>
Link: https://lore.kernel.org/r/20230224153302.45365-3-povik+lin@cutebit.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Fix the reset sequence of reads and writes that we invoke from within
the early trigger. It looks like there never was a SERDES_CONF_SOME_RST
bit that should be involved in the reset sequence, and its presence in
the driver code is a mistake from earlier.
Instead, the reset sequence should go as follows: We should switch the
the SERDES unit's SYNC_SEL mux to the value of 7 (so outside the range
of 1...6 representing cluster's SYNCGEN units), then raise the RST bit
in SERDES_STATUS and wait for it to clear.
Properly resetting the SERDES unit fixes frame desynchronization hazard
in case of long frames (longer than 4 used slots). The desynchronization
manifests itself by rotating the PCM channels.
Fixes: 3df5d0d972 ("ASoC: apple: mca: Start new platform driver")
Signed-off-by: Martin Povišer <povik+lin@cutebit.org>
Link: https://lore.kernel.org/r/20230224153302.45365-2-povik+lin@cutebit.org
Signed-off-by: Mark Brown <broonie@kernel.org>
From within the early trigger we are doing a reset of the SERDES unit,
but the final status read is on a bad address. Add the missing SERDES
unit offset in calculation of the address.
Fixes: 3df5d0d972 ("ASoC: apple: mca: Start new platform driver")
Signed-off-by: Martin Povišer <povik+lin@cutebit.org>
Link: https://lore.kernel.org/r/20230224153302.45365-1-povik+lin@cutebit.org
Signed-off-by: Mark Brown <broonie@kernel.org>
The regulators are supposed to be controlled through the
set_bias_level() component callback. Moreover, the regulators are not
enabled during probe and so, this would lead to a regulator unbalanced
use count.
Fixes: ca514c0f12 ("ASOC: Add ADAU7118 8 Channel PDM-to-I2S/TDM Converter driver")
Signed-off-by: Nuno Sá <nuno.sa@analog.com>
Link: https://lore.kernel.org/r/20230224104551.1139981-1-nuno.sa@analog.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Add mtl_mx98360a_rt5682 driver data for Chrome Rex board support.
Signed-off-by: Dharageswari.R <dharageswari.r@intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Link: https://lore.kernel.org/r/20230220080652.23136-1-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
In mt8188_etdm_clk_src_sel_put() function, val retrieved by FIELD_PREP
is shifted to the corresponding bit filed, so it can compare with the
register value directly.
Originally, the redundant bit shift of the register value results in
the wrong comparison result, so we remove bit shift operation in the
patch.
Fixes: 2babb47774 ("ASoC: mediatek: mt8188: support etdm in platform driver")
Signed-off-by: Trevor Wu <trevor.wu@mediatek.com>
Link: https://lore.kernel.org/r/20230215125017.16044-1-trevor.wu@mediatek.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Remove the sleep control in IRQ thread
and create an individual task to handel it for Jack plug in event.
This commit improves the control of ground switches in the AAD IRQ.
Signed-off-by: David Rau <David.Rau.opensource@dm.renesas.com>
Link: https://lore.kernel.org/r/20230215101045.21456-1-David.Rau.opensource@dm.renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
With the switching to dev_err_probe(), during the conversion
of GPIO calls, the return code is passed is a paratemer to it.
At the same time a copy'n'paste mistake was made, so the wrong
variable has been taken for the error reporting. Fix this.
Fixes: 3ee0d39c50 ("ASoC: soc-ac97: Convert to agnostic GPIO API")
Reported-by: kernel test robot <lkp@intel.com>
Reported-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20230215132343.35547-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
There is no reason to have a separate module for the tables file it just
holds regmap callbacks and register patches used by the main part of the
driver. Remove the separate module and merge it into the main driver
module.
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20230215105818.3315925-1-ckeepax@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Merge series from Peter Ujfalusi <peter.ujfalusi@linux.intel.com>:
The following series will enable the the Low Power Audio (LPA)
playback on Intel platforms when using IPC4.
The support is closely follows how IPC3 supports similar use case.
All depending patches are upstream and our CI have been testing
this feature for some time without issues.
Simplify code by using min helper macro for logical evaluation and value
assignment. The change also facilitates code realignment for improved
readability.
Proposed change is identified using minmax.cocci Coccinelle script.
Signed-off-by: Deepak R Varma <drv@mailo.com>
Link: https://lore.kernel.org/r/Y+p2Hn0nrtHiKwPR@ubun2204.myguest.virtualbox.org
Signed-off-by: Mark Brown <broonie@kernel.org>
The kernel is globally removing the ambiguous 0-length and 1-element
arrays in favor of flexible arrays, so that we can gain both compile-time
and run-time array bounds checking[1]. In this instance, struct
skl_cpr_cfg contains struct skl_cpr_gtw_cfg, which defined "config_data"
as a 1-element array.
However, case present in sound/soc/intel/skylake/skl-topology.h is not a
simple one as the structure takes part in IPC communication. Apparently
original definition missed one field, which while not used by AudioDSP
firmware when there is no additional data, is still expected to be part
of an IPC message. Currently this works because of how 'config_data' is
declared: 'config_data[1]'. Now when one replaces it with a flexible
array there would be one field missing. Update struct declaration to fix
this.
Reported-by: Sasa Ostrouska <casaxa@gmail.com>
Link: https://lore.kernel.org/all/CALFERdwvq5day_sbDfiUsMSZCQu9HG8-SBpOZDNPeMdZGog6XA@mail.gmail.com/
Cc: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Cc: Liam Girdwood <liam.r.girdwood@linux.intel.com>
Cc: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Cc: Bard Liao <yung-chuan.liao@linux.intel.com>
Cc: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Cc: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Cc: Mark Brown <broonie@kernel.org>
Cc: Jaroslav Kysela <perex@perex.cz>
Cc: Takashi Iwai <tiwai@suse.com>
Cc: "Gustavo A. R. Silva" <gustavoars@kernel.org>
Cc: alsa-devel@alsa-project.org
CC: Kees Cook <keescook@chromium.org>
Reviewed-by: Cezary Rojewski <cezary.rojewski@intel.com>
Signed-off-by: Amadeusz Sławiński <amadeuszx.slawinski@linux.intel.com>
Link: https://lore.kernel.org/r/20230213205223.2679357-1-amadeuszx.slawinski@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Variable ret is initialed but is never modified or used except for
returning the initial value 0. The value can be directly returned
instead and the variable definition can be dropped.
Issue identified using returnvar.cocci Coccinelle semantic patch.
Signed-off-by: Deepak R Varma <drv@mailo.com>
Link: https://lore.kernel.org/r/Y+p9r5y9DPSJkPVf@ubun2204.myguest.virtualbox.org
Signed-off-by: Mark Brown <broonie@kernel.org>
The rt5682s driver switches its regmap to cache-only when the
device suspends and back to regular mode on resume. When the
jack detect interrupt fires rt5682s_irq() schedules the jack
detect work. This can result in invalid reads from the regmap
in cache-only mode if the work runs before the device has
resumed:
[ 19.672162] rt5682s 2-001a: ASoC: error at soc_component_read_no_lock on rt5682s.2-001a for register: [0x000000f0] -16
Disable the jack detection interrupt during suspend and
re-enable it on resume. The driver already schedules the
jack detection work on resume, so any state change during
suspend is still handled.
Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Link: https://lore.kernel.org/r/20230209012002.1.Ib4d6481f1d38a6e7b8c9e04913c02ca88c216cf6@changeid
Signed-off-by: Mark Brown <broonie@kernel.org>
Enable d0i3 streaming if all the active streams can
work in d0i3 state and playback is enabled.
Signed-off-by: Rander Wang <rander.wang@intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Link: https://lore.kernel.org/r/20230214103345.30669-6-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Schedule a delayed work for d0i3 entry after every non-pm ipc msg.
Signed-off-by: Rander Wang <rander.wang@intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Link: https://lore.kernel.org/r/20230214103345.30669-5-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The driver shall update the power state to D0i0 before sending
a generic IPC. Power-related IPCs are the exception to the rule,
they may be sent even when the power-state is D0i3
Signed-off-by: Rander Wang <rander.wang@intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Link: https://lore.kernel.org/r/20230214103345.30669-4-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Use set_pm_gate to unify pm gate setting for different
ipc version.
Signed-off-by: Rander Wang <rander.wang@intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Link: https://lore.kernel.org/r/20230214103345.30669-3-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Set_pm_gate depends on ipc version. This patch defines
the ops for both IPC3 and IPC4.
Signed-off-by: Rander Wang <rander.wang@intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Link: https://lore.kernel.org/r/20230214103345.30669-2-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
When the 'ti,gpio-config' property is not defined, the
device_property_count_u32() will return an error, rather than zero.
The current check, only handles a return value of zero, which assumes that
the property is defined and has nothing defined.
This change extends the check to also check for an error case (most likely
to be hit by the case that the 'ti,gpio-config' is not defined).
In case that the 'ti,gpio-config' and the returned 'gpio_count' is not
correct, there is a 'if (gpio_count != ADCX140_NUM_GPIO_CFGS)' check, a few
lines lower that will return -EINVAL.
This means that someone tried to define 'ti,gpio-config', but with the
wrong number of GPIOs.
Fixes: d521432149 ("ASoC: tlv320adcx140: Add support for configuring GPIO pin")
Signed-off-by: Steffen Aschbacher <steffen.aschbacher@stihl.de>
Signed-off-by: Alexandru Ardelean <alex@shruggie.ro>
Link: https://lore.kernel.org/r/20230213073805.14640-1-alex@shruggie.ro
Signed-off-by: Mark Brown <broonie@kernel.org>
Change the function name aw88395_plack_event to aw88395_playback_event
Signed-off-by: Ben Yi <yijiangtao@awinic.com>
Signed-off-by: Weidong Wang <wangweidong.a@awinic.com>
Link: https://lore.kernel.org/r/20230213093649.22928-2-wangweidong.a@awinic.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Commit 2458adb8f9
("SoC: simple-card-utils: set 0Hz to sysclk when shutdown")
added a call to snd_soc_dai_set_sysclk() with 0 Hz frequency. Being
propagated further it causes a division by zero in clk-ep93xx driver:
Division by zero in kernel.
CPU: 0 PID: 52 Comm: aplay Tainted: G W 6.2.0-rc4-... #1
Hardware name: Generic DT based system
unwind_backtrace from show_stack+0x10/0x18
show_stack from dump_stack_lvl+0x28/0x34
dump_stack_lvl from __div0+0x10/0x1c
__div0 from Ldiv0+0x8/0x1c
Ldiv0 from ep93xx_mux_determine_rate+0x78/0x1d0
ep93xx_mux_determine_rate from clk_core_round_rate_nolock+0x48/0xc8
clk_core_round_rate_nolock from clk_core_set_rate_nolock+0x48/0x160
clk_core_set_rate_nolock from clk_set_rate+0x30/0x8c
clk_set_rate from ep93xx_i2s_set_sysclk+0x30/0x6c
ep93xx_i2s_set_sysclk from snd_soc_dai_set_sysclk+0x3c/0xa4
snd_soc_dai_set_sysclk from asoc_simple_shutdown+0xb8/0x164
asoc_simple_shutdown from snd_soc_link_shutdown+0x44/0x54
snd_soc_link_shutdown from soc_pcm_clean+0x78/0x180
soc_pcm_clean from soc_pcm_close+0x28/0x40
soc_pcm_close from snd_pcm_release_substream.part.0+0x3c/0x84
snd_pcm_release_substream.part.0 from snd_pcm_release+0x40/0x88
snd_pcm_release from __fput+0x74/0x278
There has been commit f1879d7b98 ("ASoC: rockchip: ignore 0Hz sysclk"),
but it prepared by far not all drivers.
Signed-off-by: Alexander Sverdlin <alexander.sverdlin@gmail.com>
Link: https://lore.kernel.org/r/20230212220923.258414-1-alexander.sverdlin@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch fixes
1. coding style issues
2. check if the setting was set already in rt712_sdca_mux_put callback
Signed-off-by: Shuming Fan <shumingf@realtek.com>
Link: https://lore.kernel.org/r/20230210082141.24077-1-shumingf@realtek.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Current rsnd silently uses default TDM width if it was strange
settings. It is difficult to notice about it.
This patch indicates warning for it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/87lel6ksqn.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Merge series from Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
From q6dsp side issues are around locking of position pointer and handle
From LPASS codec side most of the staiblity issues were around runtime pm,:
While testing X13s audio, we found multiple stablity issues this patchset
fixes these issues.
From q6dsp side issues are around locking of position pointer and handle
multiple prepare cases along with pulse audio timerbased scheduling workaround.
From LPASS codec side most of the staiblity issues were around runtime pm,
hitting various issues as the codec was firstly resetting the soundwire block
for every clk disable/enable which is taking the slaves out of sync and
resulting in re-enumerating. Second issue was around fsgen clk is not
brining up the codec out of suspend as it was not added after
runtime pm enabled. Final issue was with codec mclk rate which should
have been 192KHz same as npl instead of 96KHz. We were getting lucky as
wsa drivers are setting the same clk to 192KHz.
With this patches, x13s audio is pretty stable.
Merge series from Peter Ujfalusi <peter.ujfalusi@linux.intel.com>:
In a course of creating complicated topologies where multiple output pins of a
copier is enabled, we have discovered that additional configuration needs to be
sent to the firmware to make the use cases working.
Merge series from Herve Codina <herve.codina@bootlin.com>:
The Infineon PEB2466 codec is a programmable DSP-based four channels
codec with filters capabilities.
It also provides signals as GPIOs.
This is the initial codec driver for rt712 SDCA (Jack+Amp topology).
The host should connect with rt712 SdW1 interface.
Signed-off-by: Shuming Fan <shumingf@realtek.com>
Link: https://lore.kernel.org/r/20230207090946.20659-1-shumingf@realtek.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Simple-card/audio-graph-card drivers do not handle MCLK clock when it
is specified in the codec device node. The expectation here is that,
the codec should actually own up the MCLK clock and do necessary setup
in the driver.
This is inspired from,
commit dbf54a9534 ("ASoC: rt5659: Update MCLK rate in set_sysclk()").
Cc: Oder Chiou <oder_chiou@realtek.com>
Signed-off-by: Sameer Pujar <spujar@nvidia.com>
Link: https://lore.kernel.org/r/1675953417-8686-2-git-send-email-spujar@nvidia.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The Infineon PEB2466 codec is a programmable DSP-based four channels
codec with filters capabilities.
It also provides signals as GPIOs.
Signed-off-by: Herve Codina <herve.codina@bootlin.com>
Link: https://lore.kernel.org/r/20230206144904.91078-3-herve.codina@bootlin.com
Signed-off-by: Mark Brown <broonie@kernel.org>
MOD_INIT_INSTANCE IPC for a copier only contains the sink format for
output pin 0. Any additional output pins that are used need to have their
sink format set using the LARGE_CONFIG_SET IPC message.
Otherwise, firmware will report error or crash due to NULL format is used.
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Rander Wang <rander.wang@intel.com>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Link: https://lore.kernel.org/r/20230209142123.17193-3-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Print the queue ID's during bind/unbind errors as well to make it easier
to see what failed exactly.
Signed-off-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Link: https://lore.kernel.org/r/20230209142123.17193-2-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
resetting soundwire block will put the slaves out of sync and result
in re-enumeration during fsgen disable/enable path this is totally
unnecessary and resulting fifo overflows.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20230209122806.18923-8-srinivas.kandagatla@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
For some reason we ended up with incorrect mclk rate which should be
1920000 instead of 96000, So far we were getting lucky as the same clk
is set to 192000 by wsa and va macro. This issue is discovered when there
is no wsa macro active and only rx or tx path is tested.
Fix this by setting correct rate.
Fixes: c39667ddcf ("ASoC: codecs: lpass-tx-macro: add support for lpass tx macro")
Fixes: af3d54b997 ("ASoC: codecs: lpass-rx-macro: add support for lpass rx macro")
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20230209122806.18923-7-srinivas.kandagatla@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
currently q6apm_is_adsp_ready() will only return the cached value of
previous result. If we are unlucky and previous result is not-ready
then the caller will always get not-ready flag.
This is not correct, we should query the dsp of its current state in
irrespective of previous reported state.
Fixes: 47bc8cf60e ("ASoC: qdsp6: audioreach: Add ADSP ready check")
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20230209122806.18923-5-srinivas.kandagatla@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
At the moment, playing audio with PulseAudio with the qdsp6 driver
results in distorted sound. It seems like its timer-based scheduling
does not work properly with qdsp6 since setting tsched=0 in
the PulseAudio configuration avoids the issue.
Apparently this happens when the pointer() callback is not accurate
enough. There is a SNDRV_PCM_INFO_BATCH flag that can be used to stop
PulseAudio from using timer-based scheduling by default.
According to https://www.alsa-project.org/pipermail/alsa-devel/2014-March/073816.html:
The flag is being used in the sense explained in the previous audio
meeting -- the data transfer granularity isn't fine enough but aligned
to the period size (or less).
q6apm-dai reports the position as multiple of
prtd->pcm_count = snd_pcm_lib_period_bytes(substream)
so it indeed just a multiple of the period size.
Therefore adding the flag here seems appropriate and makes audio
work out of the box.
Comment log inspired by Stephan Gerhold sent for q6asm-dai.c few years back.
Fixes: 9b4fe0f1cd ("ASoC: qdsp6: audioreach: add q6apm-dai support")
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20230209122806.18923-4-srinivas.kandagatla@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
It is noticed that the position pointer value seems to get a get corrupted
due to missing locking between updating and reading.
Fix this by adding a spinlock around the position pointer.
Fixes: 9b4fe0f1cd ("ASoC: qdsp6: audioreach: add q6apm-dai support")
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20230209122806.18923-3-srinivas.kandagatla@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
prepare callback can be called multiple times, so unprepare the stream
if its already prepared.
Without this DSP is not happy to setting the params on a already
prepared graph.
Fixes: 9b4fe0f1cd ("ASoC: qdsp6: audioreach: add q6apm-dai support")
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20230209122806.18923-2-srinivas.kandagatla@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Claudiu Beznea
Martin Povišer
Nuno Sá
Dharageswari.R
Trevor Wu
Kiseok Jo
Joseph Hunkeler
Geert Uytterhoeven
David Rau
Andy Shevchenko
Charles Keepax
Mark Brown
Deepak R Varma
Amadeusz Sławiński
Steffen Aschbacher
Matthias Kaehlcke
Rander Wang
Yang Li
Weidong Wang
Alexander Sverdlin
Shuming Fan
Kuninori Morimoto
Sameer Pujar
Herve Codina
Bard Liao
Ranjani Sridharan
Srinivas Kandagatla