Pull operating performance points (OPP) framework fixes for 5.9-rc4 from
Viresh Kumar:
"This fixes reference counting for OPP tables. Few patches are getting
queued (for various subsystems) for 5.10 which depend on this to be
fixed first."
* 'opp/fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/vireshk/pm:
opp: Don't drop reference for an OPP table that was never parsed
dev_pm_opp_remove_table() should drop a reference to the OPP table only
if the DT OPP table was parsed earlier with a call to
dev_pm_opp_of_add_table() earlier. Else it may end up dropping the
reference to the OPP table, which was added as a result of other calls
like dev_pm_opp_set_clkname(). And would hence result in undesirable
behavior later on when caller would try to free the resource again.
Fixes: 03758d6026 ("opp: Replace list_kref with a local counter")
Reported-by: Naresh Kamboju <naresh.kamboju@linaro.org>
Reported-by: Anders Roxell <anders.roxell@linaro.org>
Tested-by: Naresh Kamboju <naresh.kamboju@linaro.org>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
dev_pm_opp_set_rate() can now be called with freq = 0 in order
to either drop performance or bandwidth votes or to disable
regulators on platforms which support them.
In such cases, a subsequent call to dev_pm_opp_set_rate() with
the same frequency ends up returning early because 'old_freq == freq'
Instead make it fall through and put back the dropped performance
and bandwidth votes and/or enable back the regulators.
Cc: v5.3+ <stable@vger.kernel.org> # v5.3+
Fixes: cd7ea58286 ("opp: Make dev_pm_opp_set_rate() handle freq = 0 to drop performance votes")
Reported-by: Sajida Bhanu <sbhanu@codeaurora.org>
Reviewed-by: Sibi Sankar <sibis@codeaurora.org>
Reported-by: Matthias Kaehlcke <mka@chromium.org>
Tested-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Rajendra Nayak <rnayak@codeaurora.org>
[ Viresh: Don't skip clk_set_rate() and massaged changelog ]
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
We get the opp_table pointer at the top of the function and so we should
put the pointer at the end of the function like all other exit paths
from this function do.
Cc: v5.8+ <stable@vger.kernel.org> # v5.8+
Fixes: b00e667a6d ("opp: Remove bandwidth votes when target_freq is zero")
Reviewed-by: Rajendra Nayak <rnayak@codeaurora.org>
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
[ Viresh: Split the patch into two ]
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
We get the opp_table pointer at the top of the function and so we should
put the pointer at the end of the function like all other exit paths
from this function do.
Cc: v5.7+ <stable@vger.kernel.org> # v5.7+
Fixes: aca48b61f9 ("opp: Manage empty OPP tables with clk handle")
Reviewed-by: Rajendra Nayak <rnayak@codeaurora.org>
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
[ Viresh: Split the patch into two ]
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Pull ARM cpufreq driver changes for v5.9-rc1 from Viresh Kumar:
"Here are the details:
- Adaptive voltage scaling (AVS) support and minor cleanups for
brcmstb driver (Florian Fainelli and Markus Mayer).
- A new tegra driver and cleanup for the existing one (Sumit Gupta and
Jon Hunter).
- Bandwidth level support for Qcom driver along with OPP changes (Sibi
Sankar).
- Cleanups to sti, cpufreq-dt, ap806, CPPC drivers (Viresh Kumar, Lee
Jones, Ivan Kokshaysky, Sven Auhagen, and Xin Hao).
- Make schedutil default governor for ARM (Valentin Schneider).
- Fix dependency issues for imx (Walter Lozano).
- Cleanup around cached_resolved_idx in cpufreq core (Viresh Kumar)."
* 'cpufreq/arm/linux-next' of git://git.kernel.org/pub/scm/linux/kernel/git/vireshk/pm:
cpufreq: make schedutil the default for arm and arm64
cpufreq: cached_resolved_idx can not be negative
cpufreq: Add Tegra194 cpufreq driver
dt-bindings: arm: Add NVIDIA Tegra194 CPU Complex binding
cpufreq: imx: Select NVMEM_IMX_OCOTP
cpufreq: sti-cpufreq: Fix some formatting and misspelling issues
cpufreq: tegra186: Simplify probe return path
cpufreq: CPPC: Reuse caps variable in few routines
cpufreq: ap806: fix cpufreq driver needs ap cpu clk
cpufreq: cppc: Reorder code and remove apply_hisi_workaround variable
cpufreq: dt: fix oops on armada37xx
cpufreq: brcmstb-avs-cpufreq: send S2_ENTER / S2_EXIT commands to AVS
cpufreq: brcmstb-avs-cpufreq: Support polling AVS firmware
cpufreq: brcmstb-avs-cpufreq: more flexible interface for __issue_avs_command()
cpufreq: qcom: Disable fast switch when scaling DDR/L3
cpufreq: qcom: Update the bandwidth levels on frequency change
OPP: Add and export helper to set bandwidth
cpufreq: blacklist SC7180 in cpufreq-dt-platdev
cpufreq: blacklist SDM845 in cpufreq-dt-platdev
Add and export 'dev_pm_opp_set_bw' to set the bandwidth
levels associated with an OPP.
Signed-off-by: Sibi Sankar <sibis@codeaurora.org>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Export dev_pm_opp_adjust_voltage() as it may be used by modules later
on.
Signed-off-by: Valdis Kletnieks <valdis.kletnieks@vt.edu>
[ Viresh: Rewrote commit log ]
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
We already drop several votes when target_freq is set to zero, drop
bandwidth votes as well.
Reported-by: Sibi Sankar <sibis@codeaurora.org>
Reviewed-by: Georgi Djakov <georgi.djakov@linaro.org>
Tested-by: Georgi Djakov <georgi.djakov@linaro.org>
Reviewed-by: Sibi Sankar <sibis@codeaurora.org>
Tested-by: Sibi Sankar <sibis@codeaurora.org>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Add enable regulators to dev_pm_opp_set_regulators() and disable
regulators to dev_pm_opp_put_regulators(). Even if bootloader
leaves regulators enabled, they should be enabled in kernel in
order to increase the reference count.
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Clément Péron <peron.clem@gmail.com>
Tested-by: Clément Péron <peron.clem@gmail.com>
Signed-off-by: Kamil Konieczny <k.konieczny@samsung.com>
[ Viresh: Enable the regulator only after it is programmed and add a
flag to track its status. ]
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Reorder the code a bit to make it more readable. Add additional comment
as well.
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Clément Péron <peron.clem@gmail.com>
Tested-by: Clément Péron <peron.clem@gmail.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
If the OPP bandwidth values are populated, we want to switch also the
interconnect bandwidth in addition to frequency and voltage.
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Sibi Sankar <sibis@codeaurora.org>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
The OPP bindings now support bandwidth values, so add support to parse it
from device tree and store it into the new dev_pm_opp_icc_bw struct, which
is part of the dev_pm_opp.
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
[ Viresh: Create _read_bw() and use it, renamed _of_find_icc_paths() to
dev_pm_opp_of_find_icc_paths(), exported it and made opp_table
argument optional. Also drop the depends on from Kconfig. ]
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
The opp-hz DT property is not mandatory and we may use another property
as a key in the OPP table. Add helper functions to simplify the reading
and comparing the keys.
Signed-off-by: Saravana Kannan <saravanak@google.com>
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Sibi Sankar <sibis@codeaurora.org>
[ Viresh: Removed an unnecessary comment ]
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
With OPP core now supporting DVFS for IO devices, we have instances of
IO devices (same IP block) which require an OPP on some platforms/SoCs
while just needing to scale the clock on some others.
In order to avoid conditional code in every driver which supports such
devices (to check for availability of OPPs and then deciding to do
either dev_pm_opp_set_rate() or clk_set_rate()) add support to manage
empty OPP tables with a clk handle.
This makes dev_pm_opp_set_rate() equivalent of a clk_set_rate() for
devices with just a clk and no OPPs specified, and makes
dev_pm_opp_set_rate(0) bail out without throwing an error.
Signed-off-by: Rajendra Nayak <rnayak@codeaurora.org>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
A kref or refcount isn't the right tool to be used here for counting
number of devices that are sharing the static OPPs created for the OPP
table. For example, we are reinitializing the kref again, after it
reaches a value of 0 and frees the resources, if the static OPPs get
added for the same OPP table structure (as the OPP table structure was
never freed). That is messy and very unclear.
This patch makes parsed_static_opps an unsigned integer and uses it to
count the number of users of the static OPPs. The increment and
decrement to parsed_static_opps is done under opp_table->lock now to
make sure no races are possible if the OPP table is getting added and
removed in parallel (which doesn't happen in practice, but can in
theory).
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
On some SoCs the Adaptive Voltage Scaling (AVS) technique is
employed to optimize the operating voltage of a device. At a
given frequency, the hardware monitors dynamic factors and either
makes a suggestion for how much to adjust a voltage for the
current frequency, or it automatically adjusts the voltage
without software intervention. Add an API to the OPP library for
the former case, so that AVS type devices can update the voltages
for an OPP when the hardware determines the voltage should
change. The assumption is that drivers like CPUfreq or devfreq
will register for the OPP notifiers and adjust the voltage
according to suggestions that AVS makes.
This patch is derived from [1] submitted by Stephen.
[1] https://lore.kernel.org/patchwork/patch/599279/
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
[Roger Lu: Changed to rcu less implementation]
Signed-off-by: Roger Lu <roger.lu@mediatek.com>
[s.nawrocki@samsung.com: added handling of OPP min/max voltage]
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
All the drivers, which use the OPP framework control regulators, which
are already enabled. Typically those regulators are also system critical,
due to providing power to CPU core or system buses. It turned out that
there are cases, where calling regulator_enable() on such boot-enabled
regulator has side-effects and might change its initial voltage due to
performing initial voltage balancing without all restrictions from the
consumers. Until this issue becomes finally solved in regulator core,
avoid calling regulator_enable()/disable() from the OPP framework.
This reverts commit 7f93ff73f7.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Add enable regulators to dev_pm_opp_set_regulators() and disable
regulators to dev_pm_opp_put_regulators(). Even if bootloader
leaves regulators enabled, they should be enabled in kernel in
order to increase the reference count.
Signed-off-by: Kamil Konieczny <k.konieczny@partner.samsung.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
The list_kref was added for static OPPs and to track their users. The
kref is initialized while the static OPPs are added, but removed
unconditionally even if the static OPPs were never added. This causes
refcount mismatch warnings currently.
Fix that by always initializing the kref when the OPP table is first
initialized. The refcount is later incremented only for the second user
onwards.
Fixes: d0e8ae6c26 ("OPP: Create separate kref for static OPPs list")
Reported-by: Rajendra Nayak <rnayak@codeaurora.org>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Since the performance states in the OPP table are unique, implement a
dev_pm_opp_find_level_exact() in order to be able to fetch a specific OPP.
Signed-off-by: Niklas Cassel <niklas.cassel@linaro.org>
[ Viresh: Updated commit log ]
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
The cpufreq drivers don't need to do runtime PM operations on the
virtual devices returned by dev_pm_domain_attach_by_name() and so the
virtual devices weren't shared with the callers of
dev_pm_opp_attach_genpd() earlier.
But the IO device drivers would want to do that. This patch updates the
prototype of dev_pm_opp_attach_genpd() to accept another argument to
return the pointer to the array of genpd virtual devices.
Reported-by: Rajendra Nayak <rnayak@codeaurora.org>
Tested-by: Rajendra Nayak <rnayak@codeaurora.org>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
A device may have multiple power-domains and not all of them may be
scalable (i.e. support performance states). But
dev_pm_opp_attach_genpd() doesn't take that into account currently.
Fix that by not verifying the names argument with "power-domain-names"
DT property and finding the index into the required-opps array. The
names argument will anyway get verified later on when we call
dev_pm_domain_attach_by_name().
Fixes: 6319aee10e ("opp: Attach genpds to devices from within OPP core")
Reported-by: Rajendra Nayak <rnayak@codeaurora.org>
Tested-by: Rajendra Nayak <rnayak@codeaurora.org>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Pull operating performance points (OPP) framework changes for v5.3
from Viresh Kumar:
"This pull request contains:
- OPP core changes to support a wider range of devices, like IO
devices (Rajendra Nayak and Stehpen Boyd).
- Fixes around genpd_virt_devs (Viresh Kumar).
- Fix for platform with set_opp() callback (Dmitry Osipenko)."
* 'opp/linux-next' of git://git.kernel.org/pub/scm/linux/kernel/git/vireshk/pm:
opp: Don't use IS_ERR on invalid supplies
opp: Make dev_pm_opp_set_rate() handle freq = 0 to drop performance votes
opp: Don't overwrite rounded clk rate
opp: Allocate genpd_virt_devs from dev_pm_opp_attach_genpd()
opp: Attach genpds to devices from within OPP core
_set_opp_custom() receives a set of OPP supplies as its arguments and
the caller of it passes NULL when the supplies are not valid. But
_set_opp_custom(), by mistake, checks for error by performing
IS_ERR(old_supply) on it which will always evaluate to false.
The problem was spotted during of testing of upcoming update for the
NVIDIA Tegra CPUFreq driver.
Cc: stable <stable@vger.kernel.org>
Fixes: 7e535993fa ("OPP: Separate out custom OPP handler specific code")
Reported-by: Marc Dietrich <marvin24@gmx.de>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
[ Viresh: Massaged changelog ]
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Based on 2 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation #
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 4122 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Enrico Weigelt <info@metux.net>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190604081206.933168790@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For devices with performance state, we use dev_pm_opp_set_rate() to set
the appropriate clk rate and the performance state.
We do need a way to remove the performance state vote when we idle the
device and turn the clocks off. Use dev_pm_opp_set_rate() with freq = 0
to achieve this.
Signed-off-by: Rajendra Nayak <rnayak@codeaurora.org>
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
[ Viresh: Updated _set_required_opps() to handle the !opp case ]
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
The OPP table normally contains 'fmax' values corresponding to the
voltage or performance levels of each OPP, but we don't necessarily want
all the devices to run at fmax all the time. Running at fmax makes sense
for devices like CPU/GPU, which have a finite amount of work to do and
since a specific amount of energy is consumed at an OPP, its better to
run at the highest possible frequency for that voltage value.
On the other hand, we have IO devices which need to run at specific
frequencies only for their proper functioning, instead of maximum
possible frequency.
The OPP core currently roundup to the next possible OPP for a frequency
and select the fmax value. To support the IO devices by the OPP core,
lets do the roundup to fetch the voltage or performance state values,
but not use the OPP frequency value. Rather use the value returned by
clk_round_rate().
The current user, cpufreq, of dev_pm_opp_set_rate() already does the
rounding to the next OPP before calling this routine and it won't
have any side affects because of this change.
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Rajendra Nayak <rnayak@codeaurora.org>
[ Viresh: Massaged changelog, added comment and use temp_opp variable
instead ]
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Currently the space for the array of virtual devices is allocated along
with the OPP table, but that isn't going to work well from now onwards.
For single power domain case, a driver can either use the original
device structure for setting the performance state (if genpd attached
with dev_pm_domain_attach()) or use the virtual device structure (if
genpd attached with dev_pm_domain_attach_by_name(), which returns the
virtual device) and so we can't know in advance if we are going to need
genpd_virt_devs array or not.
Lets delay the allocation a bit and do it along with
dev_pm_opp_attach_genpd() rather. The deallocation is done from
dev_pm_opp_detach_genpd().
Tested-by: Niklas Cassel <niklas.cassel@linaro.org>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
The OPP core requires the virtual device pointers to set performance
state on behalf of the device, for the multiple power domain case. The
genpd API (dev_pm_domain_attach_by_name()) has evolved now to support
even the single power domain case and that lets us add common code for
handling both the cases more efficiently.
The virtual device structure returned by dev_pm_domain_attach_by_name()
isn't normally used by the cpufreq drivers as they don't manage power
on/off of the domains and so is only useful for the OPP core.
This patch moves all the complexity into the OPP core to make the end
drivers simple. The earlier APIs dev_pm_opp_{set|put}_genpd_virt_dev()
are reworked into dev_pm_opp_{attach|detach}_genpd(). The new helper
dev_pm_opp_attach_genpd() accepts a NULL terminated array of strings
which contains names of all the genpd's to attach. It then attaches all
the domains and saves the pointers to the virtual devices. The other
helper undo the work done by this helper.
Tested-by: Niklas Cassel <niklas.cassel@linaro.org>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
This patch introduces a new helper routine in the OPP core, which
returns the OPP with the highest frequency which has voltage less than
or equal to the target voltage passed to the helper.
Signed-off-by: Andrew-sh.Cheng <andrew-sh.cheng@mediatek.com>
[ Viresh: Massaged the commit log and renamed the helper with some
cleanups. ]
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
At boot up, CPUFreq core performs a sanity check to see if the system is
running at a frequency defined in the frequency table of the CPU. If so,
we try to find a valid frequency (lowest frequency greater than the
currently programmed frequency) from the table and set it. When the call
reaches dev_pm_opp_set_rate(), it calls _find_freq_ceil(opp_table,
&old_freq) to find the previously configured OPP and this call also
updates the old_freq. This eventually sets the old_freq == freq (new
target requested by cpufreq core) and we skip updating the performance
state in this case.
Fix this by also updating the performance state when the old_freq ==
freq.
Fixes: ca1b5d77b1 ("OPP: Configure all required OPPs")
Cc: v5.0 <stable@vger.kernel.org> # v5.0
Reported-by: Niklas Cassel <niklas.cassel@linaro.org>
Tested-by: Jorge Ramirez-Ortiz <jorge.ramirez-ortiz@linaro.org>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
- Update the PM-runtime framework to use ktime instead of
jiffies for accounting (Thara Gopinath, Vincent Guittot).
- Optimize the autosuspend code in the PM-runtime framework
somewhat (Ladislav Michl).
- Add a PM core flag to mark devices that don't need any form of
power management (Sudeep Holla).
- Introduce driver API documentation for cpuidle and add a new
cpuidle governor for tickless systems (Rafael Wysocki).
- Add Jacobsville support to the intel_idle driver (Zhang Rui).
- Clean up a cpuidle core header file and the cpuidle-dt and ACPI
processor-idle drivers (Yangtao Li, Joseph Lo, Yazen Ghannam).
- Add new cpufreq driver for Armada 8K (Gregory Clement).
- Fix and clean up cpufreq core (Rafael Wysocki, Viresh Kumar,
Amit Kucheria).
- Add support for light-weight tear-down and bring-up of CPUs to the
cpufreq core and use it in the cpufreq-dt driver (Viresh Kumar).
- Fix cpu_cooling Kconfig dependencies, add support for CPU cooling
auto-registration to the cpufreq core and use it in multiple
cpufreq drivers (Amit Kucheria).
- Fix some minor issues and do some cleanups in the davinci,
e_powersaver, ap806, s5pv210, qcom and kryo cpufreq drivers
(Bartosz Golaszewski, Gustavo Silva, Julia Lawall, Paweł Chmiel,
Taniya Das, Viresh Kumar).
- Add a Hisilicon CPPC quirk to the cppc_cpufreq driver (Xiongfeng
Wang).
- Clean up the intel_pstate and acpi-cpufreq drivers (Erwan Velu,
Rafael Wysocki).
- Clean up multiple cpufreq drivers (Yangtao Li).
- Update cpufreq-related MAINTAINERS entries (Baruch Siach, Lukas
Bulwahn).
- Add support for exposing the Energy Model via debugfs and make
multiple cpufreq drivers register an Energy Model to support
energy-aware scheduling (Quentin Perret, Dietmar Eggemann,
Matthias Kaehlcke).
- Add Ice Lake mobile and Jacobsville support to the Intel RAPL
power-capping driver (Gayatri Kammela, Zhang Rui).
- Add a power estimation helper to the operating performance points
(OPP) framework and clean up a core function in it (Quentin Perret,
Viresh Kumar).
- Make minor improvements in the generic power domains (genpd), OPP
and system suspend frameworks and in the PM core (Aditya Pakki,
Douglas Anderson, Greg Kroah-Hartman, Rafael Wysocki, Yangtao Li).
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=TSKG
-----END PGP SIGNATURE-----
Merge tag 'pm-5.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management updates from Rafael Wysocki:
"These are PM-runtime framework changes to use ktime instead of jiffies
for accounting, new PM core flag to mark devices that don't need any
form of power management, cpuidle updates including driver API
documentation and a new governor, cpufreq updates including a new
driver for Armada 8K, thermal cleanups and more, some energy-aware
scheduling (EAS) enabling changes, new chips support in the intel_idle
and RAPL drivers and assorted cleanups in some other places.
Specifics:
- Update the PM-runtime framework to use ktime instead of jiffies for
accounting (Thara Gopinath, Vincent Guittot)
- Optimize the autosuspend code in the PM-runtime framework somewhat
(Ladislav Michl)
- Add a PM core flag to mark devices that don't need any form of
power management (Sudeep Holla)
- Introduce driver API documentation for cpuidle and add a new
cpuidle governor for tickless systems (Rafael Wysocki)
- Add Jacobsville support to the intel_idle driver (Zhang Rui)
- Clean up a cpuidle core header file and the cpuidle-dt and ACPI
processor-idle drivers (Yangtao Li, Joseph Lo, Yazen Ghannam)
- Add new cpufreq driver for Armada 8K (Gregory Clement)
- Fix and clean up cpufreq core (Rafael Wysocki, Viresh Kumar, Amit
Kucheria)
- Add support for light-weight tear-down and bring-up of CPUs to the
cpufreq core and use it in the cpufreq-dt driver (Viresh Kumar)
- Fix cpu_cooling Kconfig dependencies, add support for CPU cooling
auto-registration to the cpufreq core and use it in multiple
cpufreq drivers (Amit Kucheria)
- Fix some minor issues and do some cleanups in the davinci,
e_powersaver, ap806, s5pv210, qcom and kryo cpufreq drivers
(Bartosz Golaszewski, Gustavo Silva, Julia Lawall, Paweł Chmiel,
Taniya Das, Viresh Kumar)
- Add a Hisilicon CPPC quirk to the cppc_cpufreq driver (Xiongfeng
Wang)
- Clean up the intel_pstate and acpi-cpufreq drivers (Erwan Velu,
Rafael Wysocki)
- Clean up multiple cpufreq drivers (Yangtao Li)
- Update cpufreq-related MAINTAINERS entries (Baruch Siach, Lukas
Bulwahn)
- Add support for exposing the Energy Model via debugfs and make
multiple cpufreq drivers register an Energy Model to support
energy-aware scheduling (Quentin Perret, Dietmar Eggemann, Matthias
Kaehlcke)
- Add Ice Lake mobile and Jacobsville support to the Intel RAPL
power-capping driver (Gayatri Kammela, Zhang Rui)
- Add a power estimation helper to the operating performance points
(OPP) framework and clean up a core function in it (Quentin Perret,
Viresh Kumar)
- Make minor improvements in the generic power domains (genpd), OPP
and system suspend frameworks and in the PM core (Aditya Pakki,
Douglas Anderson, Greg Kroah-Hartman, Rafael Wysocki, Yangtao Li)"
* tag 'pm-5.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (80 commits)
cpufreq: kryo: Release OPP tables on module removal
cpufreq: ap806: add missing of_node_put after of_device_is_available
cpufreq: acpi-cpufreq: Report if CPU doesn't support boost technologies
cpufreq: Pass updated policy to driver ->setpolicy() callback
cpufreq: Fix two debug messages in cpufreq_set_policy()
cpufreq: Reorder and simplify cpufreq_update_policy()
cpufreq: Add kerneldoc comments for two core functions
PM / core: Add support to skip power management in device/driver model
cpufreq: intel_pstate: Rework iowait boosting to be less aggressive
cpufreq: intel_pstate: Eliminate intel_pstate_get_base_pstate()
cpufreq: intel_pstate: Avoid redundant initialization of local vars
powercap/intel_rapl: add Ice Lake mobile
ACPI / processor: Set P_LVL{2,3} idle state descriptions
cpufreq / cppc: Work around for Hisilicon CPPC cpufreq
ACPI / CPPC: Add a helper to get desired performance
cpufreq: davinci: move configuration to include/linux/platform_data
cpufreq: speedstep: convert BUG() to BUG_ON()
cpufreq: powernv: fix missing check of return value in init_powernv_pstates()
cpufreq: longhaul: remove unneeded semicolon
cpufreq: pcc-cpufreq: remove unneeded semicolon
..
* Add Qualcomm RPMh power domain driver and related changes
* Fix issues with sleep/wake sets and batch API in RPMh
* Update MAINTAINERS Qualcomm entry
* Fixup RMTFS-mem sysfs and uevents
* Fix error handling in GSBI
* Add SMD-RPM compatible entry for SDM660
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=CcrU
-----END PGP SIGNATURE-----
Merge tag 'qcom-drivers-for-5.1' of git://git.kernel.org/pub/scm/linux/kernel/git/agross/linux into arm/drivers
Qualcomm ARM Based Driver Updates for v5.1
* Add Qualcomm RPMh power domain driver and related changes
* Fix issues with sleep/wake sets and batch API in RPMh
* Update MAINTAINERS Qualcomm entry
* Fixup RMTFS-mem sysfs and uevents
* Fix error handling in GSBI
* Add SMD-RPM compatible entry for SDM660
* tag 'qcom-drivers-for-5.1' of git://git.kernel.org/pub/scm/linux/kernel/git/agross/linux:
soc: qcom: smd-rpm: Add sdm660 compatible
soc: qcom: gsbi: Fix error handling in gsbi_probe()
soc: qcom: rpmh: Avoid accessing freed memory from batch API
drivers: qcom: rpmh: avoid sending sleep/wake sets immediately
soc: qcom: rmtfs-mem: Make sysfs attributes world-readable
soc: qcom: rmtfs-mem: Add class to enable uevents
soc: qcom: update config dependencies for QCOM_RPMPD
soc: qcom: rpmpd: Drop family A RPM dependency
MAINTAINERS: update list of qcom drivers
soc: qcom: rpmhpd: Mark mx as a parent for cx
soc: qcom: rpmhpd: Add RPMh power domain driver
soc: qcom: rpmpd: Add support for get/set performance state
soc: qcom: rpmpd: Add a Power domain driver to model corners
dt-bindings: power: Add qcom rpm power domain driver bindings
OPP: Add support for parsing the 'opp-level' property
dt-bindings: opp: Introduce opp-level bindings
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Pull operating performance points (OPP) framework updates for v5.1
from Viresh Kumar:
"This pull request contains following changes:
- Introduced new OPP helper for power-estimation and used it in
several cpufreq drivers (Quentin Perret, Matthias Kaehlcke, Dietmar
Eggemann, and Yangtao Li).
- OPP Debugfs cleanup (Greg KH).
- OPP core cleanup (Viresh Kumar)."
* 'opp/linux-next' of git://git.kernel.org/pub/scm/linux/kernel/git/vireshk/pm:
cpufreq: OMAP: Register an Energy Model
cpufreq: imx6q: Register an Energy Model
opp: no need to check return value of debugfs_create functions
cpufreq: mediatek: Register an Energy Model
cpufreq: scmi: Register an Energy Model
cpufreq: arm_big_little: Register an Energy Model
cpufreq: scpi: Register an Energy Model
cpufreq: dt: Register an Energy Model
PM / OPP: Introduce a power estimation helper
PM / OPP: Remove unused parameter of _generic_set_opp_clk_only()
When calling debugfs functions, there is no need to ever check the
return value. The function can work or not, but the code logic should
never do something different based on this.
Cc: Viresh Kumar <vireshk@kernel.org>
Cc: Nishanth Menon <nm@ti.com>
Cc: Stephen Boyd <sboyd@kernel.org>
Cc: linux-pm@vger.kernel.org
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
The previous frequency value isn't getting used in the routine
_generic_set_opp_clk_only(), drop it.
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Now that the OPP bindings are updated to include an optional
'opp-level' property, add support to parse it from device tree
and store it as part of dev_pm_opp structure.
Also add and export an helper 'dev_pm_opp_get_level()' that can be
used to get the level value read from device tree when present.
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rajendra Nayak <rnayak@codeaurora.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Since the commit 2a4eb7358a "OPP: Don't remove dynamic OPPs from
_dev_pm_opp_remove_table()", dynamically created OPP aren't
automatically removed anymore by dev_pm_opp_cpumask_remove_table(). This
affects the scpi and scmi cpufreq drivers which no longer free OPPs on
failures or on invocations of the policy->exit() callback.
Create a generic OPP helper dev_pm_opp_remove_all_dynamic() which can be
called from these drivers instead of dev_pm_opp_cpumask_remove_table().
In dev_pm_opp_remove_all_dynamic(), we need to make sure that the
opp_list isn't getting accessed simultaneously from other parts of the
OPP core while the helper is freeing dynamic OPPs, i.e. we can't drop
the opp_table->lock while traversing through the OPP list. And to
accomplish that, this patch also creates _opp_kref_release_unlocked()
which can be called from this new helper with the opp_table lock already
held.
Cc: 4.20 <stable@vger.kernel.org> # v4.20
Reported-by: Valentin Schneider <valentin.schneider@arm.com>
Fixes: 2a4eb7358a "OPP: Don't remove dynamic OPPs from _dev_pm_opp_remove_table()"
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Tested-by: Valentin Schneider <valentin.schneider@arm.com>
Reviewed-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
dev_pm_genpd_set_performance_state() needs to handle performance state
propagation going forward. Currently this routine only gets the required
performance state of the device's genpd as an argument, but it doesn't
know how to translate that to master genpd(s) of the device's genpd.
Introduce a new helper dev_pm_opp_xlate_performance_state() which will
be used to translate from performance state of a device (or genpd
sub-domain) to another device (or master genpd).
Normally the src_table (of genpd sub-domain) will have the
"required_opps" property set to point to one of the OPPs in the
dst_table (of master genpd), but in some cases the genpd and its master
have one to one mapping of performance states and so none of them have
the "required-opps" property set. Return the performance state of the
src_table as it is in such cases.
Tested-by: Rajendra Nayak <rnayak@codeaurora.org>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
There is one case where we may end up with no "supply" directory for the
OPPs in debugfs. That happens when the OPP core isn't managing the
regulators for the device and the device's OPP do have microvolt
property. It happens because the opp_table->regulator_count remains set
to 0 and the debugfs routines don't add any supply directory in such a
case.
This commit fixes that by setting opp_table->regulator_count to 1 in
that particular case. But to make everything work nicely and not break
other parts of the core, regulator_count is defined as "int" now instead
of "unsigned int" and it can have different special values now. It is
set to -1 initially to mark it "uninitialized" and later only we set it
to 0 or positive values after checking how many supplies are there.
This also helps in finding the bugs where only few of the OPPs have the
"opp-microvolt" property set and not all.
Fixes: 1fae788ed6 ("PM / OPP: Don't create debugfs "supply-0" directory unnecessarily")
Reported-by: Quentin Perret <quentin.perret@arm.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
The value of opp_table->regulator_count is not very consistent right now
and it may end up being 0 while we do have a "opp-microvolt" property in
the OPP table. It was kept that way as we used to check if any
regulators are set with the OPP core for a device or not using value of
regulator_count.
Lets use opp_table->regulators for that purpose as the meaning of
regulator_count is going to change in the later patches.
Reported-by: Quentin Perret <quentin.perret@arm.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Now that all the infrastructure is in place to support multiple required
OPPs, lets switch over to using it.
A new internal routine _set_required_opps() takes care of updating
performance state for all the required OPPs. With this the performance
state updates are supported even when the end device needs to configure
regulators as well, that wasn't the case earlier.
The pstates were earlier stored in the end device's OPP structures, that
also changes now as those values are stored in the genpd's OPP
structures. And so we switch over to using
pm_genpd_opp_to_performance_state() instead of
of_genpd_opp_to_performance_state() to get performance state for the
genpd OPPs.
The routine _generic_set_opp_domain() is not required anymore and is
removed.
On errors we don't try to recover by reverting to old settings as things
are really complex now and the calls here should never really fail
unless there is a bug. There is no point increasing the complexity, for
code which will never be executed.
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Multiple generic power domains for a consumer device are supported with
the help of virtual devices, which are created for each consumer device
- genpd pair. These are the device structures which are attached to the
power domain and are required by the OPP core to set the performance
state of the genpd.
The helpers added by this commit are required to be called once for each
of these virtual devices. These are required only if multiple domains
are available for a device, otherwise the actual device structure will
be used instead by the OPP core.
The new helpers also support the complex cases where the consumer device
wouldn't always require all the domains. For example, a camera may
require only one power domain during normal operations but two during
high resolution operations. The consumer driver can call
dev_pm_opp_put_genpd_virt_dev(high_resolution_genpd_virt_dev) if it is
currently operating in the normal mode and doesn't have any performance
requirements from the genpd which manages high resolution power
requirements. The consumer driver can later call
dev_pm_opp_set_genpd_virt_dev(high_resolution_genpd_virt_dev) once it
switches back to the high resolution mode.
The new helpers differ from other OPP set/put helpers as the new ones
can be called with OPPs initialized for the table as we may need to call
them on the fly because of the complex case explained above. For this
reason it is possible that the genpd virt_dev structure may be used in
parallel while the new helpers are running and a new mutex is added to
protect against that. We didn't use the existing opp_table->lock mutex
as that is widely used in the OPP core and we will need this lock in the
dev_pm_opp_set_rate() helper while changing OPP and we need to make sure
there is not much contention while doing that as that's the hotpath.
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
An earlier commit populated the OPP tables from the "required-opps"
property, this commit populates the individual OPPs. This is repeated
for each OPP in the OPP table and these populated OPPs will be used by
later commits.
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
The current implementation works only for the case where a single
phandle is present in the "required-opps" property, while DT allows
multiple phandles to be present there.
This patch adds new infrastructure to parse all the phandles present in
"required-opps" property and save pointers of the required OPP's OPP
tables. These will be used by later commits.
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Create a separate routine to take care of custom set_opp() handler
specific stuff.
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Return error number instead of 0 on failures.
Fixes: a1e8c13600 ("PM / OPP: "opp-hz" is optional for power domains")
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Rafael J. Wysocki
Viresh Kumar
Rajendra Nayak
Stephen Boyd
Sibi Sankar
Andrew-sh.Cheng
Valdis Klētnieks
Kamil Konieczny
Georgi Djakov
Saravana Kannan
Stephen Boyd
Marek Szyprowski
k.konieczny@partner.samsung.com
Niklas Cassel
Dmitry Osipenko
Thomas Gleixner
Linus Torvalds
Arnd Bergmann
Greg Kroah-Hartman