Fixes a v4l2-compliance error: setting audmode to a value other than mono
or stereo for a radio device should map to MODE_STEREO.
The spec specifies that for radio devices only mono and stereo audmodes are
valid. If the user specifies another audmode in v4l2_tuner, then that should
be mapped to valid audmode. That didn't happen here.
Note that tuner drivers might decide to limit the possible audmode even
further if it only supports mono. In that case the tuner driver can set
audmode to mono. However, that new value wasn't copied back to t->audmode,
and that has been fixed as well in this patch.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch adds a v4l2 core helper function that can be used as
the log_status handler for subdevs that only need to log state
of the v4l2 controls owned by the subdev's control handler.
Signed-off-by: Sylwester Nawrocki <sylvester.nawrocki@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add a v4l2 core helper function that can be used as the subdev
.subscribe_event handler. This allows to eliminate some boilerplate
from drivers that are only handling the control events.
Signed-off-by: Sylwester Nawrocki <sylvester.nawrocki@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add a v4l2 core helper function that can be used as the subdev
.unsubscribe_event handler. This allows to eliminate some
boilerplate from drivers that are only handling the control events.
Signed-off-by: Sylwester Nawrocki <sylvester.nawrocki@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch adds a helper function that allows to modify range,
i.e. minimum, maximum, step and default value of a v4l2 control,
after the control has been created and initialized. This is helpful
in situations when range of a control depends on user configurable
parameters, e.g. camera sensor absolute exposure time depending on
an output image resolution and frame rate.
v4l2_ctrl_modify_range() function allows to modify range of an
INTEGER, BOOL, MENU, INTEGER_MENU and BITMASK type controls.
Based on a patch from Hans Verkuil http://patchwork.linuxtv.org/patch/8654.
Signed-off-by: Sylwester Nawrocki <sylvester.nawrocki@gmail.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
* v4l_for_linus: (464 commits)
[media] uvcvideo: Set error_idx properly for S_EXT_CTRLS failures
[media] uvcvideo: Cleanup leftovers of partial revert
[media] uvcvideo: Return -EACCES when trying to set a read-only control
Linux 3.8-rc3
mm: reinstante dropped pmd_trans_splitting() check
cred: Remove tgcred pointer from struct cred
drm/ttm: fix fence locking in ttm_buffer_object_transfer
ARM: clps711x: Fix bad merge of clockevents setup
ARM: highbank: save and restore L2 cache and GIC on suspend
ARM: highbank: add a power request clear
ARM: highbank: fix secondary boot and hotplug
ARM: highbank: fix typos with hignbank in power request functions
ARM: dts: fix highbank cpu mpidr values
ARM: dts: add device_type prop to cpu nodes on Calxeda platforms
drm/prime: drop reference on imported dma-buf come from gem
xen/netfront: improve truesize tracking
ARM: mx5: Fix MX53 flexcan2 clock
ARM: OMAP2+: am33xx-hwmod: Fix wrongly terminated am33xx_usbss_mpu_irqs array
sctp: fix Kconfig bug in default cookie hmac selection
EDAC: Cleanup device deregistering path
...
Conflicts:
drivers/media/pci/dm1105/dm1105.c
drivers/media/platform/soc_camera/mx2_camera.c
Add a configuration option for v4l2-int-device so it is only compiled when
necessary, which is only by omap24xxcam and tcm825x drivers.
Signed-off-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
It has been over 3 years since the V4L2_CID_[HV]CENTER were deprecated.
Clean up the DocBook and remove the V4L2_CID_VCENTER_DEPRECATED,
V4L2_CID_VCENTER_DEPRECATED control related paragraphs.
Remove the V4L2_CID_[HV]CENTER controls definitions from v4l2-controls.h,
these controls are not used by any driver in the mainline now.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Single-planar V4L2 buffers are converted to multi-planar vb2 buffers
with a single plane when queued. The plane data_offset field is not
available in the single-planar API and must be set to 0 for all output
buffers.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
When subdev registration fails the subdev v4l2_dev field is left to a
non-NULL value. Later calls to v4l2_device_unregister_subdev() will
consider the subdev as registered and will module_put() the subdev
module without any matching module_get().
Fix this by setting the subdev v4l2_dev field to NULL in
v4l2_device_register_subdev() when the function fails.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: stable@vger.kernel.org
Acked-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Sometimes platform/bridge drivers need to be notified when a control from
a sub-device changes value. In order to support this a notify callback was
added.
[dheitmueller@kernellabs.com: fix merge conflict in v4l2-ctrls.c]
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Set buffer timestamp flags for videobuf, videobuf2 and drivers that use
neither.
Signed-off-by: Sakari Ailus <sakari.ailus@iki.fi>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
v4l2_get_timestamp() produces a monotonic timestamp but unlike
ktime_get_ts(), it uses struct timeval instead of struct timespec, saving
the drivers the conversion job when getting timestamps for v4l2_buffer's
timestamp field.
Signed-off-by: Sakari Ailus <sakari.ailus@iki.fi>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The mem2mem core doesn't change struct m2m_ops, provided by the driver,
make references to it const.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The right solution is to remove the architecture dependency on
dma_common_get_sgtable(). Revert this patch to apply the right one.
This reverts commit 93049b9368.
As reported by Stephen:
> After merging the v4l-dvb tree, today's linux-next build (x86_64
> allmodconfig) failed like this:
>
> ERROR: "dma_common_get_sgtable" [drivers/media/v4l2-core/videobuf2-dma-contig.ko] undefined!
>
> Caused by commit 9ef2cbeb81 ("[media] v4l: vb2-dma-contig: add support
> for DMABUF exporting"). dma_common_get_sgtable() is called from the
> inline dma_get_sgtable_attrs() and dma_get_sgtable_attrs() is "called
> from" dma_get_sgtable(). dma_common_get_sgtable() is only defined if
> ARCH_HAS_DMA_DECLARE_COHERENT_MEMORY is set which depends on
> CONFIG_HAVE_GENERIC_DMA_COHERENT being set which it isn't for this build.
The simplest fix is to just not support DMABUF with vb2-contig, on archs
where this symbol doesn't exist. Some latter patch can rewrite it to
support this outside -arm.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Most operations on DMA and DMABUF framework require the size of a buffer to be
page aligned. This patch guarantees the requirement is satisfied for all
vb2-dma-contig buffers.
Signed-off-by: Tomasz Stanislawski <t.stanislaws@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The DMA transfer must be aligned to a specific value. If userptr is not aligned
to DMA requirements then unexpected corruptions of the memory may occur before
or after a buffer. To prevent such situations, all unligned userptr buffers
are rejected at VIDIOC_QBUF.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch adds taking reference to the device for MMAP buffers.
Such buffers, may be exported using DMABUF mechanism. If the driver that
created a queue is unloaded then the queue is released, the device might be
released too. However, buffers cannot be released if they are referenced by
DMABUF descriptor(s). The device pointer kept in a buffer must be valid for the
whole buffer's lifetime. Therefore MMAP buffers should take a reference to the
device to avoid risk of dangling pointers.
Signed-off-by: Tomasz Stanislawski <t.stanislaws@samsung.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Tested-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch adds support for exporting a dma-contig buffer using
DMABUF interface.
Signed-off-by: Tomasz Stanislawski <t.stanislaws@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Tested-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch adds extension to videobuf2-core. It allow to export an mmap buffer
as a DMABUF file descriptor.
Signed-off-by: Tomasz Stanislawski <t.stanislaws@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Tested-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch adds extension to V4L2 api. A new ioctl VIDIOC_EXPBUF is added. The
ioctl is used to export an mmap buffer as a DMABUF file descriptor.
Signed-off-by: Tomasz Stanislawski <t.stanislaws@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Tested-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Let mmap method to use dma_mmap_coherent call. Moreover, this patch removes
vb2_mmap_pfn_range from videobuf2 helpers as it was suggested by Laurent
Pinchart. The function is no longer used in vb2 code.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Tomasz Stanislawski <t.stanislaws@samsung.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch adds support for importing DMABUF files for
vmalloc allocator in Videobuf2.
Signed-off-by: Tomasz Stanislawski <t.stanislaws@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Tested-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch makes changes for adding dma-contig as a dma_buf user. It provides
function implementations for the {attach, detach, map, unmap}_dmabuf()
mem_ops of DMABUF memory type.
[author of the original patch]
[integration with refactored dma-contig allocator]
Signed-off-by: Sumit Semwal <sumit.semwal@ti.com>
Signed-off-by: Sumit Semwal <sumit.semwal@linaro.org>
Signed-off-by: Tomasz Stanislawski <t.stanislaws@samsung.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Tested-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch adds support for prepare/finish callbacks in VB2 allocators. These
callback are used for buffer flushing.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Tested-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch introduces usage of dma_map_sg to map memory behind
a userspace pointer to a device as dma-contiguous mapping.
This patch contains some of the code kindly provided by Marek Szyprowski
<m.szyprowski@samsung.com> and Kamil Debski <k.debski@samsung.com> and Andrzej
Pietrasiewicz <andrzej.p@samsung.com>. Kind thanks for bug reports from Laurent
Pinchart <laurent.pinchart@ideasonboard.com> and Seung-Woo Kim
<sw0312.kim@samsung.com>.
Signed-off-by: Tomasz Stanislawski <t.stanislaws@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch removes a reference to alloc_ctx from an instance of a DMA
contiguous buffer. It helps to avoid a risk of a dangling pointer if the
context is released while the buffer is still valid. Moreover it removes one
dereference step while accessing a device structure.
Signed-off-by: Tomasz Stanislawski <t.stanislaws@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Tested-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Adding DMABUF memory type causes videobuf to complain about not using it
in some switch cases. This patch removes these warnings.
Signed-off-by: Sumit Semwal <sumit.semwal@ti.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Tested-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch adds support for DMABUF memory type in videobuf2. It calls relevant
APIs of dma_buf for v4l reqbuf / qbuf / dqbuf operations.
For this version, the support is for videobuf2 as a user of the shared buffer;
so the allocation of the buffer is done outside of V4L2. [A sample allocator of
dma-buf shared buffer is given at [1]]
[1]: Rob Clark's DRM:
https://github.com/robclark/kernel-omap4/commits/drmplane-dmabuf
[original work in the PoC for buffer sharing]
Signed-off-by: Tomasz Stanislawski <t.stanislaws@samsung.com>
Signed-off-by: Sumit Semwal <sumit.semwal@ti.com>
Signed-off-by: Sumit Semwal <sumit.semwal@linaro.org>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Tested-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Adds DMABUF memory type to v4l framework. Also adds the related file
descriptor in v4l2_plane and v4l2_buffer.
[original work in the PoC for buffer sharing]
Signed-off-by: Tomasz Stanislawski <t.stanislaws@samsung.com>
Signed-off-by: Sumit Semwal <sumit.semwal@ti.com>
Signed-off-by: Sumit Semwal <sumit.semwal@linaro.org>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Tested-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
v4l2_subdev_link_validate_get_format() retrieves the remote pad format
depending on the entity type and prints a warning if the entity type is
not supported. The type check doesn't take the subtype into account, and
thus always prints a warning for device node types, even when supported.
Fix it.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Update contact information to correspond my e-mail address changes.
Signed-off-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
See following thread for rationale:
http://www.spinics.net/lists/linux-media/msg52462.html
Tested by compilation only.
Signed-off-by: Nicolas Thery <nicolas.thery@st.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Pull second set of media updates from Mauro Carvalho Chehab:
"Despite its size, most of the stuff here is trivial. This series
contains:
- s5p-mfc: additions at the driver and at the core to support H.264
hardware codec;
- Some improvements at s5p and davinci embedded drivers;
- Some V4L2 compliance fixes applied on a few drivers;
- Several random trivial patches, including several fixes and a few
new board support additions;
Notes:
1) Some Exynos media patches were dependent on some -arm fixes that
got merged on changeset 782cd9e. That's why this pull request is
based that changeset.
2) As promised, I reviewed the pending VB2 DMABUF series.
While setting a test environment, it was noticed that the upstream
support for Samsung Exynos 4 boards (smdk310 and Origen) are
broken upstream, likely due to regressions: both defconfigs are
wrong and regulator settings for both boards are broken. That,
allied with some bug at the dummy regulator driver, causes OOPSes
during boot time.
Long story short: even fixing the above, the proposed patches
OOPSed when running the DMABUF test. Not sure yet if the OOPSes
are due to some other undetected regressions, or due to some bug
on the patches.
Due to the above, DMABUF patches for vb2 got NACKed for 3.7."
* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (109 commits)
[media] m5mols: Add missing #include <linux/sizes.h>
[media] stk1160: Add support for S-Video input
Revert "[media] omap3isp: Replace cpu_is_omap3630() with ISP revision check"
[media] dvb: LNA implementation changes
[media] v4l2-ioctl: fix W=1 warnings
[media] v4l2-ioctl: add blocks check for VIDIOC_SUBDEV_G/S_EDID
[media] omap3isp: Fix compilation error in ispreg.h
[media] rc-msi-digivox-ii: Add full scan keycodes
[media] cx25821: testing the wrong variable
[media] tda18271-common: hold the I2C adapter during write transfers
[media] ds3000: add module parameter to force firmware upload
[media] drivers/media: Remove unnecessary semicolon
[media] winbond: remove space from driver name
[media] iguanair: cannot send data from the stack
[media] omap3isp: Replace cpu_is_omap3630() with ISP revision check
[media] dvb-usb: print small buffers via %*ph
[media] uvc: Add return code check at vb2_queue_init()
[media] em28xx: Replace memcpy with struct assignment
[media] bt8xx: Add video4linux control V4L2_CID_COLOR_KILLER
[media] mem2mem_testdev: Use devm_kzalloc() in probe
...
Conflicts:
arch/arm/mach-davinci/include/mach/da8xx.h
A long time ago, in v2.4, VM_RESERVED kept swapout process off VMA,
currently it lost original meaning but still has some effects:
| effect | alternative flags
-+------------------------+---------------------------------------------
1| account as reserved_vm | VM_IO
2| skip in core dump | VM_IO, VM_DONTDUMP
3| do not merge or expand | VM_IO, VM_DONTEXPAND, VM_HUGETLB, VM_PFNMAP
4| do not mlock | VM_IO, VM_DONTEXPAND, VM_HUGETLB, VM_PFNMAP
This patch removes reserved_vm counter from mm_struct. Seems like nobody
cares about it, it does not exported into userspace directly, it only
reduces total_vm showed in proc.
Thus VM_RESERVED can be replaced with VM_IO or pair VM_DONTEXPAND | VM_DONTDUMP.
remap_pfn_range() and io_remap_pfn_range() set VM_IO|VM_DONTEXPAND|VM_DONTDUMP.
remap_vmalloc_range() set VM_DONTEXPAND | VM_DONTDUMP.
[akpm@linux-foundation.org: drivers/vfio/pci/vfio_pci.c fixup]
Signed-off-by: Konstantin Khlebnikov <khlebnikov@openvz.org>
Cc: Alexander Viro <viro@zeniv.linux.org.uk>
Cc: Carsten Otte <cotte@de.ibm.com>
Cc: Chris Metcalf <cmetcalf@tilera.com>
Cc: Cyrill Gorcunov <gorcunov@openvz.org>
Cc: Eric Paris <eparis@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Hugh Dickins <hughd@google.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: James Morris <james.l.morris@oracle.com>
Cc: Jason Baron <jbaron@redhat.com>
Cc: Kentaro Takeda <takedakn@nttdata.co.jp>
Cc: Matt Helsley <matthltc@us.ibm.com>
Cc: Nick Piggin <npiggin@kernel.dk>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Robert Richter <robert.richter@amd.com>
Cc: Suresh Siddha <suresh.b.siddha@intel.com>
Cc: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Cc: Venkatesh Pallipadi <venki@google.com>
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Since the prt_names() macro is always called with an unsigned index the
((a) >= 0) condition is always true and gives a compiler warning when
compiling with W=1.
Rewrite the macro to avoid that warning, but cast the index to unsigned
just in case it is ever called with a signed argument.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The maximum size of an EDID is 32768 bytes, which is 32768 / 128 = 256 blocks.
Return -EINVAL if blocks > 256 to ensure that the memory allocation is sane.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The core code for PREPARE_BUF didn't take the multiplanar case into account,
which might cause page faults. Handle PREPARE_BUF just like QUERYBUF and
QBUF/DQBUF.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
length should be set to num_planes in __fill_v4l2_buffer(). That way the
caller knows how many planes there are in the buffer.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The plane verification should be done before actually queuing or
dequeuing buffers, so move it out of __fill_v4l2_buffer and __fill_vb_buffer
and call it as a separate step.
This also makes it possible to change the return type of __fill_v4l2/vb_buffer
to void.
The dqbuf case took some special care: before removing a buffer from the
done_list you have to verify that the receiving v4l2_buffer has enough room
for all the planes. The number of planes can differ between buffers due to the
fact that buffers for other formats can be prepared using VIDIOC_PREPARE_BUF.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Reviewed-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Tested-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add helper function v4l2_ctrl_new_std_menu_items(), which adds
a standard menu control, with driver specific menu.
Signed-off-by: Lad, Prabhakar <prabhakar.lad@ti.com>
Signed-off-by: Manjunath Hadli <manjunath.hadli@ti.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
add V4L2_CID_TEST_PATTERN of type menu, which determines
the internal test pattern selected by the device.
Signed-off-by: Lad, Prabhakar <prabhakar.lad@ti.com>
Signed-off-by: Manjunath Hadli <manjunath.hadli@ti.com>
Acked-by: Sakari Ailus <sakari.ailus@iki.fi>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
With a filter function you can control more precisely which controls
are added. This is useful in particular for radio device nodes for
combined TV/Radio cards where you want to show just the radio-specific
controls and not controls like brightness.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The vidioc_overlay op needs an unsigned int, not an unsigned int pointer.
So we need a small function that dereferences the unsigned int pointer.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This replaces BUG_ON() calls with WARN_ON(), and returns
EINVAL if some parameter is NULL, as suggested by Jonathan and Mauro.
The BUG_ON() call is too drastic to be used in this case.
See the full discussion here:
http://www.spinics.net/lists/linux-media/msg52462.html
Signed-off-by: Ezequiel Garcia <elezegarcia@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
We want to check the contents not the array itself versus NULL
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Check against q->fileio to see if the queue owner should be set or not.
The former check against the return value of read or write is wrong, since
read/write can return an error, even if the queue is in streaming mode.
For example, EAGAIN when in non-blocking mode.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This makes it easier to read and also ties in more closely with the
profile concept.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The ioctl validity checks have been improved and now take vfl_type
and vfl_dir into account.
During the 2012 Media Workshop it was decided that these improved
v4l2 core checks should be added as they simplified drivers and
made drivers behave consistently.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Write-only ioctls should have a const argument in the ioctl op.
Do this conversion for vidioc_(un)subscribe_event.
Adding const for write-only ioctls was decided during the 2012 Media Workshop.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The 'custom' timings are no longer just for custom timings, but also for standard
CEA/VESA timings. So rename to V4L2_IN/OUT_CAP_DV_TIMINGS.
The old define is still kept for backwards compatibility.
This decision was taken during the 2012 Media Workshop.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Currently the core code looks at tvnorms to see whether ENUMSTD
or G_PARM should be enabled. This is not a good check for drivers
that support the STD API on one input and the DV Timings API on another.
In that case tvnorms may be 0.
Instead check whether s_std is present (for ENUMSTD) or whether g_std or
current_norm is present for g_parm.
Also, in the enumstd core function return ENODATA if tvnorms is 0,
because in that case the current input does not support the STD API
and ENUMSTD should return ENODATA for that.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Reviewed-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This buffer type isn't used at all, and since it is effectively undefined
what it should do it is deprecated. The define still exists, but any
internal support for such buffers is removed.
The decisions to deprecate this was taken during the 2012 Media Workshop.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Use list_first_entry instead of list_entry which makes the intention
of the code more clear.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Pawel Osciak <pawel@osciak.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
These helper functions get and set a 64-bit control's value from within
a driver. They are similar to v4l2_ctrl_[gs]_ctrl() but operate on
64-bit integer controls instead of 32-bit controls.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
These two helper functions detect whether the analog video timings detected
by the video receiver match the VESA CVT or GTF standards.
They basically do the inverse of the CVT and GTF modeline calculations.
This patch also adds a helper function that will determine the aspect ratio
based on the provided EDID values. This aspect ratio can be given to the GTF
helper function.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add the v4l_match_dv_timings function that can be used to compare two
v4l2_dv_timings structs.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)
iQEcBAABAgAGBQJQNUEyAAoJEHm+PkMAQRiGs+sH/iLtdAVcfBfUwdmGV0qDXbVE
L3gCg3IERPCSaQo8qsT3zujdLAQ2HsiMs73jbqJaBWSV16ZMqkglRKbn+QMGpqJV
bi/pf5Akrm9IL/u+427ycB8QxzyjGal8uJ6btuwXa03VROSfOsEiQbtsByFNaDv/
8oq0/DaE8mWRedlcAaeN+l8nD4Enb2jSKp0UADkBMnUr4KCbwSVQ+ITXAggqVq23
htA3Yt0oGf1JYq+k99D5k92h0I/4VwiorUgwPKhmS5DM9gVtJ4L+SigbekS/MFq+
huyzOHRWlO++OxBlgSTMuJAE1k/G2B7tGeoERY0tEL/hAWcKYTfGIXSc7X6JvM0=
=Dmsv
-----END PGP SIGNATURE-----
Merge tag 'v3.6-rc3' into staging/for_v3.7
Linux 3.6-rc3
* tag 'v3.6-rc3': (764 commits)
Linux 3.6-rc3
task_work: add a scheduling point in task_work_run()
fs: fix fs/namei.c kernel-doc warnings
eventpoll: use-after-possible-free in epoll_create1()
vfio: grab vfio_device reference *before* exposing the sucker via fd_install()
vfio: get rid of vfio_device_put()/vfio_group_get_device* races
vfio: get rid of open-coding kref_put_mutex
introduce kref_put_mutex()
vfio: don't dereference after kfree...
fbcon: fix race condition between console lock and cursor timer (v1.1)
mm: compaction: Abort async compaction if locks are contended or taking too long
mm: have order > 0 compaction start near a pageblock with free pages
rapidio/tsi721: fix unused variable compiler warning
rapidio/tsi721: fix inbound doorbell interrupt handling
drivers/rtc/rtc-rs5c348.c: fix hour decoding in 12-hour mode
mm: correct page->pfmemalloc to fix deactivate_slab regression
drivers/rtc/rtc-pcf2123.c: initialize dynamic sysfs attributes
mm/compaction.c: fix deferring compaction mistake
drivers/misc/sgi-xp/xpc_uv.c: SGI XPC fails to load when cpu 0 is out of IRQ resources
string: do not export memweight() to userspace
...
- get rid of ridden V4L2_COMMON symbol
This symbol is not needed anymore; it can be folded with V4L2
one, simplifying the Kconfig a little bit;
- Comment why some Kconfig items are needed;
- Remove if test for MEDIA_CAMERA_SUPPORT, replacing it by
depends on.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Reorganize the API core changes for them to appear closer to
the items that enable them, and not at the drivers part of
the menu.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Move the tuners one level up, as the "common" directory will be used
by drivers that are shared between more than one driver.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Raise the DVB frontends one level up, as the intention is to remove
the drivers/media/dvb directory.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
just like the V4L2 core, move the DVB core to drivers/media, as the
intention is to get rid of both "video" and "dvb" directories.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Currently, the v4l2 core is mixed together with other non-core drivers.
Move them into a separate directory.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Hans Verkuil
Sylwester Nawrocki
Mauro Carvalho Chehab
Sakari Ailus
Sylwester Nawrocki
Laurent Pinchart
Guennadi Liakhovetski
Tomasz Stanislawski
Marek Szyprowski
Sumit Semwal
Nicolas THERY
Linus Torvalds
Konstantin Khlebnikov
Arun Kumar K
Lad, Prabhakar
Ezequiel Garcia
Alan Cox
Sascha Hauer