Commit 03c4749dd6 ("gpio / ACPI: Drop unnecessary ACPI GPIO to Linux
GPIO translation") has made the cherryview gpio numbers sparse, to get
a 1:1 mapping between ACPI pin numbers and gpio numbers in Linux.
This has greatly simplified things, but the code setting the
irq_valid_mask was not updated for this, so the valid mask is still in
the old "compressed" numbering with the gaps in the pin numbers skipped,
which is wrong as irq_valid_mask needs to be expressed in gpio numbers.
This results in the following error on devices using pin 24 (0x0018) on
the north GPIO controller as an ACPI event source:
[ 0.422452] cherryview-pinctrl INT33FF:01: Failed to translate GPIO to IRQ
This has been reported (by email) to be happening on a Caterpillar CAT T20
tablet and I've reproduced this myself on a Medion Akoya e2215t 2-in-1.
This commit uses the pin number instead of the compressed index into
community->pins to clear the correct bits in irq_valid_mask for GPIOs
using GPEs for interrupts, fixing these errors and in case of the
Medion Akoya e2215t also fixing the LID switch not working.
Cc: stable@vger.kernel.org
Fixes: 03c4749dd6 ("gpio / ACPI: Drop unnecessary ACPI GPIO to Linux GPIO translation")
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
When consumer requests a pin, in order to be on the safest side,
we switch it first to GPIO mode followed by immediate transition
to the input state. Due to posted writes it's luckily to be a single
I/O transaction.
However, if firmware or boot loader already configures the pin
to the GPIO mode, user expects no glitches for the requested pin.
We may check if the pin is pre-configured and leave it as is
till the actual consumer toggles its state to avoid glitches.
Fixes: 7981c0015a ("pinctrl: intel: Add Intel Sunrisepoint pin controller and GPIO support")
Depends-on: f5a26acf01 ("pinctrl: intel: Initialize GPIO properly when used through irqchip")
Cc: stable@vger.kernel.org
Cc: fei.yang@intel.com
Reported-by: Oliver Barta <oliver.barta@aptiv.com>
Reported-by: Malin Jonsson <malin.jonsson@ericsson.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
For the new Spreadtrum pin controller, it expands 6bits to describe the
pin sleep mode with adding one CM4_SLEEP mode, which means the pin sleep
related configuration will be loaded automatically by hardware when the
CM4 system goes into deep sleep mode.
Signed-off-by: Bruce Chen <bruce.chen@unisoc.com>
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Link: https://lore.kernel.org/r/8ae52263b0625c416461821c457e6789b67170b6.1571228451.git.baolin.wang@linaro.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
AST2600 EMMC support 3 types DAT bus sizes (1, 4 and 8-bit),
corresponding to 3 groups: EMMCG1, EMMCG4 and EMMCG8
Fixes: 58dc52ad00a0 ("pinctrl: aspeed: Add AST2600 pinmux support")
Signed-off-by: Johnny Huang <johnny_huang@aspeedtech.com>
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Link: https://lore.kernel.org/r/20191008044153.12734-8-andrew@aj.id.au
Reviewed-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
When UART13G1 is set the pinmux configuration in SCU4B8 for UART13G0
should be cleared.
Fixes: 58dc52ad00a0 ("pinctrl: aspeed: Add AST2600 pinmux support")
Signed-off-by: Johnny Huang <johnny_huang@aspeedtech.com>
[AJ: Tweak commit message]
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Link: https://lore.kernel.org/r/20191008044153.12734-7-andrew@aj.id.au
Reviewed-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signal descriptors can represent multi-bit bitfields and so have
explicit "enable" and "disable" states. However many descriptor
instances only describe a single bit, and so the SIG_DESC_SET() macro is
provides an abstraction for the single-bit cases: Its expansion
configures the "enable" state to set the bit and "disable" to clear.
SIG_DESC_CLEAR() was introduced to provide a similar single-bit
abstraction for for descriptors to clear the bit of interest. However
its behaviour was defined as the literal inverse of SIG_DESC_SET() - the
impact is the bit of interest is set in the disable path. This behaviour
isn't intuitive and doesn't align with how we want to use the macro in
practice, so make it clear the bit for both the enable and disable
paths.
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Link: https://lore.kernel.org/r/20191008044153.12734-6-andrew@aj.id.au
Reviewed-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The documentation to configure I3C3/FSI1 and I3C4/FSI2 was initially
unclear.
Fixes: 58dc52ad00a0 ("pinctrl: aspeed: Add AST2600 pinmux support")
Signed-off-by: Johnny Huang <johnny_huang@aspeedtech.com>
[AJ: Tweak commit message, resolve rebase conflicts]
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Link: https://lore.kernel.org/r/20191008044153.12734-5-andrew@aj.id.au
Reviewed-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The I2C function the pin participated in was incorrectly named SDA14
which lead to a failure to mux:
[ 6.884344] No function I2C14 found on pin 7 (7). Found signal(s) MACLINK4, SDA14, GPIOA7 for function(s) MACLINK4, SDA14, GPIOA7
Fixes: 58dc52ad00a0 ("pinctrl: aspeed: Add AST2600 pinmux support")
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Link: https://lore.kernel.org/r/20191008044153.12734-4-andrew@aj.id.au
Reviewed-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Some pins crept in that weren't ordered in the list.
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Link: https://lore.kernel.org/r/20191008044153.12734-3-andrew@aj.id.au
Reviewed-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
We need to convert all old gpio irqchips to pass the irqchip
setup along when adding the gpio_chip. For more info see
drivers/gpio/TODO.
For chained irqchips this is a pretty straight-forward
conversion.
Cc: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20191014111154.9731-2-linus.walleij@linaro.org
The latent IRQs are IRQs that have occurred when the system
was down in deep sleep and the GPIO block was powered off.
The PRCMU (power reset and control unit) knows which GPIO
line offset fired an IRQ to wake the system up (if so
desired) and this second IRQ was used to replay the action
when the system came back online after suspend().
This is now known to be the wrong approach to solve this
problem: in a patch series Lina Iyer has suggested to
instead make it possible to model the IRQs as hierarchical
with double parents.
Also the current device trees do not contain the right
information to make this code work, the latent IRQ is not
specified nowadays giving noise like this in the console:
[ 0.612168] gpio 8012e000.gpio: IRQ index 1 not found
[ 0.622523] gpio 8012e080.gpio: IRQ index 1 not found
Let's delete the latent IRQ code and reimplement it properly
when we need it.
Cc: Ulf Hansson <ulf.hansson@linaro.org>
Cc: Lina Iyer <ilina@codeaurora.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20191014111154.9731-1-linus.walleij@linaro.org
When an STMFX IO is used as interrupt through the interrupt-controller
binding, the STMFX driver should configure this IO as input. Default
value of STMFX IO direction is input, but if the IO is used as output
before the interrupt use, it will not work without these callbacks.
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
Link: https://lore.kernel.org/r/20191009091606.17283-1-amelie.delaunay@st.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add the pinctrl driver to support pin configuration with the
pinctrl framework on MSM8976, MSM8956, APQ8056, APQ8076.
Signed-off-by: AngeloGioacchino Del Regno <kholk11@gmail.com>
Link: https://lore.kernel.org/r/20191005105936.31216-2-kholk11@gmail.com
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
We need to convert all old gpio irqchips to pass the irqchip
setup along when adding the gpio_chip. For more info see
drivers/gpio/TODO.
For chained irqchips this is a pretty straight-forward
conversion.
Cc: Thierry Reding <thierry.reding@gmail.com>
Acked-by: Zhou Yanjie <zhouyanjie@zoho.com>
Acked-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20191001133209.17164-1-linus.walleij@linaro.org
Add support for the PM6150 and PM6150L GPIO support to the
Qualcomm PMIC GPIO binding.
Signed-off-by: Kiran Gunda <kgunda@codeaurora.org>
Link: https://lore.kernel.org/r/1570188039-22122-1-git-send-email-kgunda@codeaurora.org
Acked-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
We need to convert all old gpio irqchips to pass the irqchip
setup along when adding the gpio_chip. For more info see
drivers/gpio/TODO.
For chained irqchips this is a pretty straight-forward
conversion.
Cc: Andrew Bresticker <abrestic@chromium.org>
Cc: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: James Hartley <james.hartley@sondrel.com>
Link: https://lore.kernel.org/r/20191001214536.18477-1-linus.walleij@linaro.org
We need to convert all old gpio irqchips to pass the irqchip
setup along when adding the gpio_chip. For more info see
drivers/gpio/TODO.
For chained irqchips this is a pretty straight-forward
conversion.
Cc: Miquel Raynal <miquel.raynal@bootlin.com>
Cc: Gregory CLEMENT <gregory.clement@bootlin.com>
Cc: Marek Behún <marek.behun@nic.cz>
Cc: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20191002121550.16104-1-linus.walleij@linaro.org
We need to convert all old gpio irqchips to pass the irqchip
setup along when adding the gpio_chip. For more info see
drivers/gpio/TODO.
For chained irqchips this is a pretty straight-forward
conversion.
Cc: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20191002114454.9684-1-linus.walleij@linaro.org
The function should be spdifib, fix this typo.
Fixes: 423ddc580b ("pinctrl: berlin: add the as370 SoC pinctrl driver")
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Link: https://lore.kernel.org/r/20191011154321.44f08f9a@xhacker.debian
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
We need to convert all old gpio irqchips to pass the irqchip
setup along when adding the gpio_chip. For more info see
drivers/gpio/TODO.
For chained irqchips this is a pretty straight-forward
conversion.
Cc: Neil Armstrong <narmstrong@baylibre.com>
Cc: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20191002113819.4927-1-linus.walleij@linaro.org
We need to convert all old gpio irqchips to pass the irqchip
setup along when adding the gpio_chip. For more info see
drivers/gpio/TODO.
For chained irqchips this is a pretty straight-forward
conversion: the ST pin controller errors out of adding a
irqchip if the interrupt is invalid or missing or if the
irqmux is not present: the irqchip should not be added
if either of these errors happen, so rewrite the code to
deal with that. Keep the exit path where the gpio_chip
is added no matter what the status of the irq is.
Cc: Benjamin Gaignard <benjamin.gaignard@st.com>
Cc: Amelie Delaunay <amelie.delaunay@st.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20191001135147.29416-1-linus.walleij@linaro.org
We need to convert all old gpio irqchips to pass the irqchip
setup along when adding the gpio_chip. For more info see
drivers/gpio/TODO.
For chained irqchips this is a pretty straight-forward
conversion: at91 is a little bit special since it registers
up to 3 gpio_chips with the same parent handler, but just
passing girq->parent_handler and the parent on the first
of them should cut it.
Cc: Nicolas Ferre <nicolas.ferre@microchip.com>
Cc: Alexandre Belloni <alexandre.belloni@bootlin.com>
Cc: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Link: https://lore.kernel.org/r/20191001130645.8350-1-linus.walleij@linaro.org
This patch allows PINMUX_IPSR_PHYS() to set bits in GPSR.
When assigning function to pin, GPSR should be set to peripheral
function.
For example when using SCL3, GPSR2 bit7 (PWM1_A pin) should be set to
peripheral function.
Signed-off-by: Keiya Nobuta <nobuta.keiya@fujitsu.com>
Link: https://lore.kernel.org/r/20191008060112.29819-1-nobuta.keiya@fujitsu.com
Fixes: 50d1ba1764 ("pinctrl: sh-pfc: Add physical pin multiplexing helper macros")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Don't populate the array reg_drive on the stack but instead make it
static. Makes the object code smaller by 32 bytes.
Before:
text data bss dec hex filename
31991 15696 0 47687 ba47 drivers/pinctrl/pinctrl-rzn1.o
After:
text data bss dec hex filename
31863 15792 0 47655 ba27 drivers/pinctrl/pinctrl-rzn1.o
(gcc version 9.2.1, amd64)
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Link: https://lore.kernel.org/r/20191007140559.11840-1-colin.king@canonical.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
This includes two fixes for Intel pinctrl drivers:
- Fix warning about shared irqchip
- Restore Strago DMI workaround for all versions
-----BEGIN PGP SIGNATURE-----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=xjVF
-----END PGP SIGNATURE-----
Merge tag 'intel-pinctrl-fixes-v5.4' of git://git.kernel.org/pub/scm/linux/kernel/git/pinctrl/intel into fixes
intel-pinctrl fixes for v5.4
This includes two fixes for Intel pinctrl drivers:
- Fix warning about shared irqchip
- Restore Strago DMI workaround for all versions
The configuration registers for the LED group have inverted
polarity, which puts the GPIO into open-drain state when used in
GPIO mode. Switch to '0' for GPIO and '1' for LED modes.
Fixes: 87466ccd94 ("pinctrl: armada-37xx: Add pin controller support for Armada 37xx")
Signed-off-by: Patrick Williams <alpawi@amazon.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20191001155154.99710-1-alpawi@amazon.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
dev_get_platdata(&pdev->dev) returns a pointer on struct stmfx_pinctrl,
not on struct stmfx (platform_set_drvdata(pdev, pctl); in probe).
Pointer on struct stmfx is stored in driver data of pdev parent (in probe:
struct stmfx *stmfx = dev_get_drvdata(pdev->dev.parent);).
Fixes: 1490d9f841 ("pinctrl: Add STMFX GPIO expander Pinctrl/GPIO driver")
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
Link: https://lore.kernel.org/r/20191004122342.22018-1-amelie.delaunay@st.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
platform_get_irq() can return an error code. Allow for this when getting
the irq.
Fixes: 6f265e5d4d ("pinctrl: bcm-iproc: Pass irqchip when adding gpiochip")
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Link: https://lore.kernel.org/r/20191003000310.17099-2-chris.packham@alliedtelesis.co.nz
Acked-by: Scott Branden <scott.branden@broadcom.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Use the dev_name(dev) for the irqc->name so that we get unique names
when we have multiple instances of this driver.
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Link: https://lore.kernel.org/r/20191003000310.17099-3-chris.packham@alliedtelesis.co.nz
Acked-by: Scott Branden <scott.branden@broadcom.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The pinctrl->functions[] array has pinctrl->num_functions elements and
the pinctrl->groups[] array is the same way. These are set in
ns2_pinmux_probe(). So the > comparisons should be >= so that we don't
read one element beyond the end of the array.
Fixes: b5aa1006e4 ("pinctrl: ns2: add pinmux driver support for Broadcom NS2 SoC")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Link: https://lore.kernel.org/r/20190926081426.GB2332@mwanda
Acked-by: Scott Branden <scott.branden@broadcom.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This convert the BCM IPROC driver to use the SPDX header
for indicating GPL v2.0 only licensing.
Cc: Pramod Kumar <pramodku@broadcom.com>
Cc: Ray Jui <rjui@broadcom.com>
Cc: Scott Branden <sbranden@broadcom.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Scott Branden <scott.branden@broadcom.com>
Link: https://lore.kernel.org/r/20191002130217.4491-1-linus.walleij@linaro.org
The 37xx configuration registers are only 32 bits long, so
pins 32-35 spill over into the next register. The calculation
for the register address was done, but the bitmask was not, so
any configuration to pin 32 or above resulted in a bitmask that
overflowed and performed no action.
Fix the register / offset calculation to also adjust the offset.
Fixes: 5715092a45 ("pinctrl: armada-37xx: Add gpio support")
Signed-off-by: Patrick Williams <alpawi@amazon.com>
Acked-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20191001154634.96165-1-alpawi@amazon.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The helper pinctrl_dt_has_hogs() was introduced in
99e4f67508 (pinctrl: core: Use delayed work for hogs), but the sole
use then got removed shortly after in 950b0d91dc (pinctrl: core: Fix
regression caused by delayed work for hogs).
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Link: https://lore.kernel.org/r/20190923142005.5632-1-linux@rasmusvillemoes.dk
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add a comment about why the call to of_match_node() cannot be replaced
by of_device_get_match_data(). This will hopefully prevent people from
attempting to clean this up in the future.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Link: https://lore.kernel.org/r/20190923095400.GA11084@ulmo
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The call to pinctrl_count_index_with_args checks for a -EINVAL return
however this function calls pinctrl_get_list_and_count and this can
return -ENOENT. Rather than check for a specific error, fix this by
checking for any error return to catch the -ENOENT case.
Addresses-Coverity: ("Improper use of negative")
Fixes: 003910ebc8 ("pinctrl: Introduce TI IOdelay configuration driver")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Link: https://lore.kernel.org/r/20190920122030.14340-1-colin.king@canonical.com
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Now that the GPIO core has support for hierarchical IRQ chips, convert
Qualcomm's ssbi-gpio over to use these new helpers to reduce duplicated
code across drivers.
Signed-off-by: Brian Masney <masneyb@onstation.org>
Link: https://lore.kernel.org/r/20190914111010.24384-1-masneyb@onstation.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
When populating the pinctrl mapping table entries for a device, the
'dev_name' field for each entry is initialised to point directly at the
string returned by 'dev_name()' for the device and subsequently used by
'create_pinctrl()' when looking up the mappings for the device being
probed.
This is unreliable in the presence of calls to 'dev_set_name()', which may
reallocate the device name string leaving the pinctrl mappings with a
dangling reference. This then leads to a use-after-free every time the
name is dereferenced by a device probe:
| BUG: KASAN: invalid-access in strcmp+0x20/0x64
| Read of size 1 at addr 13ffffc153494b00 by task modprobe/590
| Pointer tag: [13], memory tag: [fe]
|
| Call trace:
| __kasan_report+0x16c/0x1dc
| kasan_report+0x10/0x18
| check_memory_region
| __hwasan_load1_noabort+0x4c/0x54
| strcmp+0x20/0x64
| create_pinctrl+0x18c/0x7f4
| pinctrl_get+0x90/0x114
| devm_pinctrl_get+0x44/0x98
| pinctrl_bind_pins+0x5c/0x450
| really_probe+0x1c8/0x9a4
| driver_probe_device+0x120/0x1d8
Follow the example of sysfs, and duplicate the device name string before
stashing it away in the pinctrl mapping entries.
Cc: Linus Walleij <linus.walleij@linaro.org>
Reported-by: Elena Petrova <lenaptr@google.com>
Tested-by: Elena Petrova <lenaptr@google.com>
Signed-off-by: Will Deacon <will@kernel.org>
Link: https://lore.kernel.org/r/20191002124206.22928-1-will@kernel.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Implement .get_multiple and .set_multiple to allow reading or setting
multiple pins simultaneously. Pins in the same bank will all be switched at
the same time, improving synchronization and performances.
Keep the driver future proof by allowing its use on 64bits platforms if
they ever appear with this IP and we end up with a mismatch between
ATMEL_PIO_NPINS_PER_BANK and BITS_PER_LONG.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Acked-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Link: https://lore.kernel.org/r/20190918113657.25998-1-alexandre.belloni@bootlin.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Several functions use for_each_child_of_node() loop with a break to find
a matching child node. Although each iteration of
for_each_child_of_node puts the previous node, but early exit from loop
misses it. This leads to leak of device node.
Cc: <stable@vger.kernel.org>
Fixes: 9a2c1c3b91 ("pinctrl: samsung: Allow grouping multiple pinmux/pinconf nodes")
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
In s3c64xx_eint_eint0_init() the for_each_child_of_node() loop is used
with a break to find a matching child node. Although each iteration of
for_each_child_of_node puts the previous node, but early exit from loop
misses it. This leads to leak of device node.
Cc: <stable@vger.kernel.org>
Fixes: 61dd726131 ("pinctrl: Add pinctrl-s3c64xx driver")
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
In s3c24xx_eint_init() the for_each_child_of_node() loop is used with a
break to find a matching child node. Although each iteration of
for_each_child_of_node puts the previous node, but early exit from loop
misses it. This leads to leak of device node.
Cc: <stable@vger.kernel.org>
Fixes: af99a75074 ("pinctrl: Add pinctrl-s3c24xx driver")
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
In exynos_eint_wkup_init() the for_each_child_of_node() loop is used
with a break to find a matching child node. Although each iteration of
for_each_child_of_node puts the previous node, but early exit from loop
misses it. This leads to leak of device node.
Cc: <stable@vger.kernel.org>
Fixes: 43b169db18 ("pinctrl: add exynos4210 specific extensions for samsung pinctrl driver")
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Each iteration of for_each_child_of_node puts the previous node, but in
the case of a return from the middle of the loop, there is no put, thus
causing a memory leak. Hence add an of_node_put before the return of
exynos_eint_wkup_init() error path.
Issue found with Coccinelle.
Signed-off-by: Nishka Dasgupta <nishkadg.linux@gmail.com>
Cc: <stable@vger.kernel.org>
Fixes: 14c255d35b ("pinctrl: exynos: Add irq_chip instance for Exynos7 wakeup interrupts")
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
This is essentially a revert of:
e3f72b749d pinctrl: cherryview: fix Strago DMI workaround
86c5dd6860 pinctrl: cherryview: limit Strago DMI workarounds to version 1.0
because even with 1.1 versions of BIOS there are some pins that are
configured as interrupts but not claimed by any driver, and they
sometimes fire up and result in interrupt storms that cause touchpad
stop functioning and other issues.
Given that we are unlikely to qualify another firmware version for a
while it is better to keep the workaround active on all Strago boards.
Reported-by: Alex Levin <levinale@chromium.org>
Fixes: 86c5dd6860 ("pinctrl: cherryview: limit Strago DMI workarounds to version 1.0")
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Alex Levin <levinale@chromium.org>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Keeping the IRQ chip definition static shares it with multiple instances of
the GPIO chip in the system. This is bad and now we get this warning from
GPIO library:
"detected irqchip that is shared with multiple gpiochips: please fix the driver."
Hence, move the IRQ chip definition from being driver static into the struct
intel_pinctrl. So a unique IRQ chip is used for each GPIO chip instance.
Fixes: ee1a6ca43d ("pinctrl: intel: Add Intel Broxton pin controller support")
Depends-on: 5ff56b015e ("pinctrl: intel: Disable GPIO pin interrupts in suspend")
Reported-by: Federico Ricchiuto <fed.ricchiuto@gmail.com>
Suggested-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Renesas RZ/G2N (r8a774b1) is pin compatible with R-Car M3-N (r8a77965),
however it doesn't have several automotive specific peripherals. Add
a r8a77965 specific pin groups/functions along with common pin
groups/functions for supporting both r8a77965 and r8a774b1 SoC.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Link: https://lore.kernel.org/r/1568881036-4404-9-git-send-email-biju.das@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
This reverts commit e167d723e1.
According to the R-Car Gen3 Hardware Manual Errata for Rev 1.00 of Aug
24, 2018, the SEL_SIMCARD_{0,1} definition was to be deleted. However,
this errata merely fixed an accidental double definition in the Hardware
User's Manual Rev. 1.00. The real definition is still present in later
revisions of the manual (Rev. 1.50 and Rev. 2.00).
Hence revert the commit to recover the definition.
Based on a patch in the BSP by Takeshi Kihara
<takeshi.kihara.df@renesas.com>.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Link: https://lore.kernel.org/r/20190904121658.2617-4-geert+renesas@glider.be
This reverts commit e87882eb9b.
According to the R-Car Gen3 Hardware Manual Errata for Rev 1.00 of Aug
24, 2018, the SEL_SSI2_{0,1} definition was to be deleted. However,
this errata merely fixed an accidental double definition in the Hardware
User's Manual Rev. 1.00. The real definition is still present in later
revisions of the manual (Rev. 1.50 and Rev. 2.00).
Hence revert the commit to recover the definition.
Based on a patch in the BSP by Takeshi Kihara
<takeshi.kihara.df@renesas.com>.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Link: https://lore.kernel.org/r/20190904121658.2617-3-geert+renesas@glider.be
The Hardware Manual Errata for Rev. 1.50 of April 10, 2019 renamed IPSR2
register bit[23:20] value H'3 and register bit[27:24] value H'3 from
AVB_AVTP_MATCH_A resp. AVB_AVTP_CAPTURE_A to AVB_AVTP_MATCH resp.
AVB_AVTP_CAPTURE.
Update the R-Car E3 pin control driver to reflect this.
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
[geert: Reword, reference errata]
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Link: https://lore.kernel.org/r/20190904121658.2617-2-geert+renesas@glider.be
We need to convert all old gpio irqchips to pass the irqchip
setup along when adding the gpio_chip. For more info see
drivers/gpio/TODO.
For chained irqchips this is a pretty straight-forward
conversion.
Cc: Barry Song <baohua@kernel.org>
Cc: Yuping Luo <yuping.luo@csr.com>
Cc: Rongjun Ying <rongjun.ying@csr.com>
Cc: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20190913113530.5536-6-linus.walleij@linaro.org
We need to convert all old gpio irqchips to pass the irqchip
setup along when adding the gpio_chip. For more info see
drivers/gpio/TODO.
For chained irqchips this is a pretty straight-forward
conversion.
Cc: Barry Song <baohua@kernel.org>
Cc: Yuping Luo <yuping.luo@csr.com>
Cc: Rongjun Ying <rongjun.ying@csr.com>
Cc: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20190913113530.5536-5-linus.walleij@linaro.org
We need to convert all old gpio irqchips to pass the irqchip
setup along when adding the gpio_chip. For more info see
drivers/gpio/TODO.
For chained irqchips this is a pretty straight-forward
conversion.
Cc: Tomer Maimon <tmaimon77@gmail.com>
Cc: Kun Yi <kunyi@google.com>
Cc: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20190913113530.5536-4-linus.walleij@linaro.org
We need to convert all old gpio irqchips to pass the irqchip
setup along when adding the gpio_chip. For more info see
drivers/gpio/TODO.
For chained irqchips this is a pretty straight-forward
conversion.
Cc: Shiraz Hashim <shiraz.linux.kernel@gmail.com>
Cc: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Link: https://lore.kernel.org/r/20190913113530.5536-3-linus.walleij@linaro.org
We need to convert all old gpio irqchips to pass the irqchip
setup along when adding the gpio_chip. For more info see
drivers/gpio/TODO.
For chained irqchips this is a pretty straight-forward
conversion.
Cc: Joshua Henderson <joshua.henderson@microchip.com>
Cc: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20190913113530.5536-2-linus.walleij@linaro.org
We need to convert all old gpio irqchips to pass the irqchip
setup along when adding the gpio_chip. For more info see
drivers/gpio/TODO.
For chained irqchips this is a pretty straight-forward
conversion.
Cc: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20190913113530.5536-1-linus.walleij@linaro.org
cycle:
Core changes:
- Fix errors in example code in the documentation.
New drivers:
- Add support for JZ4760, JZ4760B, X1000, X1000E and X1500 to
the Ingenic driver.
- Support Cirrus Logic Madera CS47L92 and CS47L15.
- Support Allwinner Sunxi V3S.
- Support Aspeed 2600 BMC.
- Support Qualcomm SC7180.
- Support Marvell MVEBU CS115.
Driver improvements:
- Clean up a few drivers to use the devm_platform_ioremap_resource()
helper.
- Pass the irqchip when registering the gpio_chip in some pin
controllers that are also GPIO controllers.
- Support suspend/resume in the Tegra driver.
- Support pull-up on the Broadcom BCM2711.
- The Intel driver can now request locked pads.
- Fix the UFS reset pin in the Qualcomm SDM845 driver.
-----BEGIN PGP SIGNATURE-----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=2nNz
-----END PGP SIGNATURE-----
Merge tag 'pinctrl-v5.4-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control updates from Linus Walleij:
"This is the bulk of pin control changes for the v5.4 kernel cycle:
Core changes:
- Fix errors in example code in the documentation.
New drivers:
- Add support for JZ4760, JZ4760B, X1000, X1000E and X1500 to the
Ingenic driver.
- Support Cirrus Logic Madera CS47L92 and CS47L15.
- Support Allwinner Sunxi V3S.
- Support Aspeed 2600 BMC.
- Support Qualcomm SC7180.
- Support Marvell MVEBU CS115.
Driver improvements:
- Clean up a few drivers to use the devm_platform_ioremap_resource()
helper.
- Pass the irqchip when registering the gpio_chip in some pin
controllers that are also GPIO controllers.
- Support suspend/resume in the Tegra driver.
- Support pull-up on the Broadcom BCM2711.
- The Intel driver can now request locked pads.
- Fix the UFS reset pin in the Qualcomm SDM845 driver"
* tag 'pinctrl-v5.4-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (112 commits)
pinctrl: meson-gxbb: Fix wrong pinning definition for uart_c
pinctrl: sh-pfc: Unlock on error in sh_pfc_func_set_mux()
pinctrl: bcm: remove redundant assignment to pointer log
pinctrl: iproc: Add 'get_direction' support
pinctrl: iproc-gpio: Handle interrupts for multiple instances
pinctrl: iproc-gpio: Fix incorrect pinconf configurations
pinctrl: intel: mark intel_pin_to_gpio __maybe_unused
pinctrl: qcom: sdm845: Fix UFS_RESET pin
pinctrl: mvebu: add additional variant for standalone CP115
pinctrl: mvebu: Add CP110 missing pin functionality
dt-bindings: cp110: document the new CP115 pinctrl compatible
pinctrl: bcm2835: Pass irqchip when adding gpiochip
pinctrl: meson: meson: Add of_node_put() before return
pinctrl/gpio: Take MUX usage into account
dt-bindings: pinctrl: qcom-pmic-gpio: Add pm8150l support
dt-bindings: pinctrl: qcom-pmic-gpio: Add pm8150b support
dt-bindings: pinctrl: qcom-pmic-gpio: Add pm8150 support
pinctrl: amd: disable spurious-firing GPIO IRQs
pinctrl: rza2: Include the appropriate headers
pinctrl: rza2: Drop driver use of consumer flags
...
v5.4 kernel cycle.
Core changes:
- Support hierarchical GPIO irqchips. We now have three
consumers that can use this: Intel IXP4xx, ThunderX and
Qualcomm SPMI GPIO (in the pinctrl subsystem). The support
code has been long in the making and hashed out so it should
be easily adaptable for all hierarchical irqchip parents.
The code only gets compiled in if hierarchical irqchip
is used at the topmost irq controller at least, as the
hierarchical irqchip requires strict hierarchy all the
way up in the system.
- Determine the need for a "valid_mask" for GPIO lines on the
gpio_chip and conversely for the "valid_mask" for the GPIO
interrupt chip interrupt lines by looking for a
.init_valid_mask() callback in the main chip or GPIO interrupt
chip respectively. Allocate it with bitmap_alloc().
- Isolate the device tree/open firmware GPIO description code
out in its own file properly.
- Isolate the ACPI GPIO description code out in its own file
properly.
- Drop a whole lot of #ifdef:s in the main includes: it does
not hurt to keep the include items around, and we get
quicker and clearer compile failures if the appropriate
kernel symbols are not selected for drivers.
New/deleted drivers:
- New driver for Aspeed SGPIO.
- The KS8695 driver is deleted as the platform gets deleted
from arch/arm in this kernel cycle.
- The Cirrus Logic Madera driver now supports CS47L92 and
CS47L15.
- The Freescale MPC8xxx now supports LS1028A and LS1088A.
Driver improvements:
- We pass the GPIO irqchip intialization by directly filling
in the struct instead of using set-up functions (the new
way) for Intel MID, Lynxpoint, Merrifield, XLP, HLWD, Aspeed,
ZX, VF610, TQMX86, MT7621, Zynq and EP93xx.
Out-of-band changes:
- Fix a GPIO header inclusion in Unicore - no response from
maintainer.
- Drop FMC subsystem from MAINTAINERS - was deleted in the
GPIO tree last cycle so let's mop up the shards.
-----BEGIN PGP SIGNATURE-----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=/TRI
-----END PGP SIGNATURE-----
Merge tag 'gpio-v5.4-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO updates from Linus Walleij:
"This is the bulk of changes in the GPIO subsystem for the v5.4 kernel
cycle.
Core changes:
- Support hierarchical GPIO irqchips.
We now have three consumers that can use this: Intel IXP4xx,
ThunderX and Qualcomm SPMI GPIO (in the pinctrl subsystem).
The support code has been long in the making and hashed out so it
should be easily adaptable for all hierarchical irqchip parents.
The code only gets compiled in if hierarchical irqchip is used at
the topmost irq controller at least, as the hierarchical irqchip
requires strict hierarchy all the way up in the system.
- Determine the need for a "valid_mask" for GPIO lines on the
gpio_chip and conversely for the "valid_mask" for the GPIO
interrupt chip interrupt lines by looking for a .init_valid_mask()
callback in the main chip or GPIO interrupt chip respectively.
Allocate it with bitmap_alloc().
- Isolate the device tree/open firmware GPIO description code out in
its own file properly.
- Isolate the ACPI GPIO description code out in its own file
properly.
- Drop a whole lot of #ifdef:s in the main includes: it does not hurt
to keep the include items around, and we get quicker and clearer
compile failures if the appropriate kernel symbols are not selected
for drivers.
New/deleted drivers:
- New driver for Aspeed SGPIO.
- The KS8695 driver is deleted as the platform gets deleted from
arch/arm in this kernel cycle.
- The Cirrus Logic Madera driver now supports CS47L92 and CS47L15.
- The Freescale MPC8xxx now supports LS1028A and LS1088A.
Driver improvements:
- We pass the GPIO irqchip intialization by directly filling in the
struct instead of using set-up functions (the new way) for Intel
MID, Lynxpoint, Merrifield, XLP, HLWD, Aspeed, ZX, VF610, TQMX86,
MT7621, Zynq and EP93xx.
Out-of-band changes:
- Fix a GPIO header inclusion in Unicore - no response from
maintainer.
- Drop FMC subsystem from MAINTAINERS - was deleted in the GPIO tree
last cycle so let's mop up the shards"
* tag 'gpio-v5.4-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (82 commits)
gpiolib: of: add a fallback for wlf,reset GPIO name
gpio: htc-egpio: Remove unused exported htc_egpio_get_wakeup_irq()
gpio: remove explicit comparison with 0
gpio: creg-snps: use devm_platform_ioremap_resource() to simplify code
gpio: devres: Switch to EXPORT_SYMBOL_GPL()
gpio: of: Switch to EXPORT_SYMBOL_GPL()
gpio: of: Make of_gpio_simple_xlate() private
gpio: of: Make of_get_named_gpiod_flags() private
gpio: aspeed: Add in ast2600 details to Aspeed driver
gpio: aspeed: Use ngpio property from device tree if available
gpio: aspeed: Setup irqchip dynamically
gpio/aspeed: Fix incorrect number of banks
gpio: aspeed: Update documentation with ast2600 controllers
gpio: Initialize the irqchip valid_mask with a callback
gpiolib: acpi: make acpi_can_fallback_to_crs() static
gpio: Fix further merge errors
gpio: Fix up merge collision in include file
gpio: of: Normalize return code variable name
gpio: gpiolib: Normalize return code variable name
gpio: ep93xx: Pass irqchip when adding gpiochip
...
We need to unlock and enable IRQs before we return on this error path.
Fixes: 8a0cc47ccc ("pinctrl: sh-pfc: Rollback to mux if required when the gpio is freed")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Link: https://lore.kernel.org/r/20190827093927.GB8443@mwanda
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Just a single fix for build warning introduced in the previous pull.
-----BEGIN PGP SIGNATURE-----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=86cF
-----END PGP SIGNATURE-----
Merge tag 'intel-pinctrl-v5.4-2' of git://git.kernel.org/pub/scm/linux/kernel/git/pinctrl/intel into devel
intel-pinctrl for v5.4 part 2
Just a single fix for build warning introduced in the previous pull.
The pointer log is being initialized with a value that is never read
and is being re-assigned a little later on. The assignment is
redundant and hence can be removed.
Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Link: https://lore.kernel.org/r/20190905140919.29283-1-colin.king@canonical.com
Reviewed-by: Ray Jui <ray.jui@broadcom.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Commit 674fa8daa8 ("pinctrl: aspeed-g5: Delay acquisition of regmaps")
was determined to be a partial fix to the problem of acquiring the LPC
Host Controller and GFX regmaps: The AST2500 pin controller may need to
fetch syscon regmaps during expression evaluation as well as when
setting mux state. For example, this case is hit by attempting to export
pins exposing the LPC Host Controller as GPIOs.
An optional eval() hook is added to the Aspeed pinmux operation struct
and called from aspeed_sig_expr_eval() if the pointer is set by the
SoC-specific driver. This enables the AST2500 to perform the custom
action of acquiring its regmap dependencies as required.
John Wang tested the fix on an Inspur FP5280G2 machine (AST2500-based)
where the issue was found, and I've booted the fix on Witherspoon
(AST2500) and Palmetto (AST2400) machines, and poked at relevant pins
under QEMU by forcing mux configurations via devmem before exporting
GPIOs to exercise the driver.
Fixes: 7d29ed88ac ("pinctrl: aspeed: Read and write bits in LPC and GFX controllers")
Fixes: 674fa8daa8 ("pinctrl: aspeed-g5: Delay acquisition of regmaps")
Reported-by: John Wang <wangzqbj@inspur.com>
Tested-by: John Wang <wangzqbj@inspur.com>
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Link: https://lore.kernel.org/r/20190829071738.2523-1-andrew@aj.id.au
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
When multiple instance of iproc-gpio chips are present, a fix up
message[1] is printed during the probe of second and later instances.
This issue is because driver sharing same irq_chip data structure
among multiple instances of driver.
Fix this by allocating irq_chip data structure per instance of
iproc-gpio.
[1] fix up message addressed by this patch
[ 7.862208] gpio gpiochip2: (689d0000.gpio): detected irqchip that
is shared with multiple gpiochips: please fix the driver.
Fixes: 616043d58a ("pinctrl: Rename gpio driver from cygnus to iproc")
Signed-off-by: Rayagonda Kokatanur <rayagonda.kokatanur@broadcom.com>
Link: https://lore.kernel.org/r/1567054348-19685-3-git-send-email-srinath.mannam@broadcom.com
[Rebased on top of new irq chip set-up code]
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
After changing the valid_mask for the struct gpio_chip
to detect the need and presence of a valid mask with the
presence of a .init_valid_mask() callback to fill it in,
we augment the gpio_irq_chip to use the same logic.
Switch all driver using the gpio_irq_chio valid_mask
over to this new method.
This makes sure the valid_mask for the gpio_irq_chip gets
filled in when we add the gpio_chip, which makes it a
little easier to switch over drivers using the old
way of setting up gpio_irq_chip over to the new method
of passing the gpio_irq_chip along with the gpio_chip.
(See drivers/gpio/TODO for details.)
Cc: Joel Stanley <joel@jms.id.au>
Cc: Thierry Reding <treding@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Link: https://lore.kernel.org/r/20190904140104.32426-1-linus.walleij@linaro.org
The intel_pin_to_gpio() function is only called by the
PM support functions and causes a warning when those are disabled:
drivers/pinctrl/intel/pinctrl-intel.c:841:12: error: unused function 'intel_pin_to_gpio' [-Werror,-Wunused-function]
Mark it __maybe_unused to suppress the warning.
Suggested-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Chris Chiu <chiu@endlessm.com>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
The UFS_RESET pin is the magical pin #150 now, not 153 per the
sdm845_groups array declared in this file. Fix the order of pins so that
UFS_RESET is 150 and the SDC pins follow after.
Fixes: 53a5372ce3 ("pinctrl: qcom: sdm845: Expose ufs_reset as gpio")
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Link: https://lore.kernel.org/r/20190830060227.12792-1-swboyd@chromium.org
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
A collection of improvements and fixes for Intel pinctrl drivers
including:
- Converting drivers to use new devm_platform_ioremap_resource()
helper function.
- Make Interrupt Status (IS) register configurable.
- Allow locked pins to be requested and used as long as they are not
modified.
- Fix intel_pinctrl_should_save() to translate pin number to GPIO
number where needed. This fixes Asus X571GT touchpad
unresponsiveness issue after suspend/resume cycle.
-----BEGIN PGP SIGNATURE-----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=owt6
-----END PGP SIGNATURE-----
Merge tag 'intel-pinctrl-v5.4' of git://git.kernel.org/pub/scm/linux/kernel/git/pinctrl/intel into devel
intel-pinctrl for v5.4
A collection of improvements and fixes for Intel pinctrl drivers
including:
- Converting drivers to use new devm_platform_ioremap_resource()
helper function.
- Make Interrupt Status (IS) register configurable.
- Allow locked pins to be requested and used as long as they are not
modified.
- Fix intel_pinctrl_should_save() to translate pin number to GPIO
number where needed. This fixes Asus X571GT touchpad
unresponsiveness issue after suspend/resume cycle.
With CP115 standalone modules, all MPP configuration are
possible. Handle this new possibility thanks to the new
"marvell,cp115-standalone-pinctrl" compatible property.
Signed-off-by: Grzegorz Jaszczyk <jaz@semihalf.com>
[<miquel.raynal@bootlin.com>: mention the new compatible in the
commit log]
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/r/20190805101607.29811-4-miquel.raynal@bootlin.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add missing definition for function 0xe on CP-110 MPP-62.
The pin function is Data Strobe for SDIO interface.
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/r/20190805101607.29811-2-miquel.raynal@bootlin.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
We need to convert all old gpio irqchips to pass the irqchip
setup along when adding the gpio_chip. For more info see
drivers/gpio/TODO.
For chained irqchips this is a pretty straight-forward
conversion. The BCM2835 has multiple parents so let's
exploit the new facility in the GPIO_IRQCHIP to actually
deal with multiple parents.
Cc: Eric Anholt <eric@anholt.net>
Cc: Thierry Reding <treding@nvidia.com>
[Rebased on changes in the pinctrl tree]
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Link: https://lore.kernel.org/r/20190812062729.1892-1-linus.walleij@linaro.org
- Support switching between function and gpio at runtime,
- Small fixes and cleanups.
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQQ9qaHoIs/1I4cXmEiKwlD9ZEnxcAUCXV/gVwAKCRCKwlD9ZEnx
cLpQAP0XZb56DbtrskUWuRpLEg/CRiiQFG0INFqCTQclCLqTAgEAv7g0gmqx7tvk
Kjdjp2D2KL8P88/cRYTX3nRPfphBdAI=
=D5la
-----END PGP SIGNATURE-----
Merge tag 'sh-pfc-for-v5.4-tag2' of https://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-drivers into devel
pinctrl: sh-pfc: Updates for v5.4 (take two)
- Support switching between function and gpio at runtime,
- Small fixes and cleanups.
Each iteration of for_each_child_of_node puts the previous node, but in
the case of a return from the middle of the loop, there is no put, thus
causing a memory leak. Hence add an of_node_put before the return.
Issue found with Coccinelle.
Signed-off-by: Nishka Dasgupta <nishkadg.linux@gmail.com>
Link: https://lore.kernel.org/r/20190815060718.3286-1-nishkadg.linux@gmail.com
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The user space like gpioinfo only see the GPIO usage but not the
MUX usage (e.g. I2C or SPI usage) of a pin. As a user we want
to know which pin is free/safe to use. So take the MUX usage of
strict pinmux controllers into account to get a more realistic
view for ioctl GPIO_GET_LINEINFO_IOCTL.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Tested-by: Ramon Fried <rfried.dev@gmail.com>
Signed-off-by: Ramon Fried <rfried.dev@gmail.com>
Link: https://lore.kernel.org/r/20190814110035.13451-1-ramon.fried@linux.intel.com
Acked-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
When cold-booting Asus X434DA, GPIO 7 is found to be already configured
as an interrupt, and the GPIO level is found to be in a state that
causes the interrupt to fire.
As soon as pinctrl-amd probes, this interrupt fires and invokes
amd_gpio_irq_handler(). The IRQ is acked, but no GPIO-IRQ handler was
invoked, so the GPIO level being unchanged just causes another interrupt
to fire again immediately after.
This results in an interrupt storm causing this platform to hang
during boot, right after pinctrl-amd is probed.
Detect this situation and disable the GPIO interrupt when this happens.
This enables the affected platform to boot as normal. GPIO 7 actually is
the I2C touchpad interrupt line, and later on, i2c-multitouch loads and
re-enables this interrupt when it is ready to handle it.
Instead of this approach, I considered disabling all GPIO interrupts at
probe time, however that seems a little risky, and I also confirmed that
Windows does not seem to have this behaviour: the same 41 GPIO IRQs are
enabled under both Linux and Windows, which is a far larger collection
than the GPIOs referenced by the DSDT on this platform.
Signed-off-by: Daniel Drake <drake@endlessm.com>
Link: https://lore.kernel.org/r/20190814090540.7152-1-drake@endlessm.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This driver is implementing a GPIO driver so include
<linux/gpio/driver.h> and not the legacy API <linux/gpio.h>.
When testing it turns out it also relies on implicit
inclusion of <linux/io.h> (readw etc) so make sure to
include that as well.
Cc: Chris Brandt <chris.brandt@renesas.com>
Cc: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
These flags are for consumers of GPIO lines, not for
drivers.
Cc: Chris Brandt <chris.brandt@renesas.com>
Cc: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Each iteration of for_each_child_of_node puts the previous node, but in
the case of a return from the middle of the loop, there is no put, thus
causing a memory leak. Hence add an of_node_put before the return in
three places.
Issue found with Coccinelle.
Signed-off-by: Nishka Dasgupta <nishkadg.linux@gmail.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
This is a GPIO driver, use the appropriate header
<linux/gpio/driver.h> rather than the legacy <linux/gpio.h>
header.
Cc: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Some drivers require switching between function and gpio at run-time.
Allow to roll back from gpio to mux when the gpio is freed.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Each iteration of for_each_child_of_node puts the previous node, but in
the case of a return from the middle of the loop, there is no put, thus
causing a memory leak. Hence add an of_node_put before the return in
three places.
Issue found with Coccinelle.
Signed-off-by: Nishka Dasgupta <nishkadg.linux@gmail.com>
Link: https://lore.kernel.org/r/20190815060609.3056-1-nishkadg.linux@gmail.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The ST pinctrl driver wants to provode a gpio_chip but is not
including the header for this, fix the inclusion to use the right
header. <linux/of_gpio.h> has to remain as the driver is calling
of_get_named_gpio().
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Maxime Coquelin <maxime.coquelin@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20190820111135.10701-1-linus.walleij@linaro.org
Static structures rk805_pinctrl_desc and rk805_gpio_chip, of types
gpio_chip and pinctrl_desc respectively, are not used except to be
copied into the fields of a different variable. Hence make
rk805_pinctrl_desc and rk805_gpio_chip both constant to protect them
from unintended modification.
Issue found with Coccinelle.
Signed-off-by: Nishka Dasgupta <nishkadg.linux@gmail.com>
Link: https://lore.kernel.org/r/20190819075757.1753-1-nishkadg.linux@gmail.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This patch adds pinctrl register read to flush all the prior pinctrl
writes and then adds barrier for pinctrl register read to complete
during resume to make sure all pinctrl changes are effective.
Acked-by: Thierry Reding <treding@nvidia.com>
Reviewed-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Sowjanya Komatineni <skomatineni@nvidia.com>
Link: https://lore.kernel.org/r/1565984527-5272-3-git-send-email-skomatineni@nvidia.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
pmx_writel uses writel which inserts write barrier before the
register write.
This patch has fix to replace writel with writel_relaxed followed
by a readback and memory barrier to ensure write operation is
completed for successful pinctrl change.
Acked-by: Thierry Reding <treding@nvidia.com>
Reviewed-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Sowjanya Komatineni <skomatineni@nvidia.com>
Link: https://lore.kernel.org/r/1565984527-5272-2-git-send-email-skomatineni@nvidia.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
YueHaibing
Hans de Goede
Andy Shevchenko
Bruce Chen
Johnny Huang
Andrew Jeffery
Linus Walleij
Jianqun Xu
Baolin Wang
Amelie Delaunay
AngeloGioacchino Del Regno
Kiran Gunda
Jisheng Zhang
Keiya Nobuta
Colin Ian King
Patrick Williams
Chris Brandt
Chris Packham
Dan Carpenter
Rasmus Villemoes
Thierry Reding
Brian Masney
Will Deacon
Alexandre Belloni
Krzysztof Kozlowski
Nishka Dasgupta
Dmitry Torokhov
Biju Das
Geert Uytterhoeven
Takeshi Kihara
Linus Torvalds
Otto Meier
Rayagonda Kokatanur
Li Jin
Arnd Bergmann
Stephen Boyd
Grzegorz Jaszczyk
Konstantin Porotchkin
Stefan Wahren
Vinod Koul
Daniel Drake
Yoshihiro Shimoda
Sowjanya Komatineni