Pull networking fixes from David Miller:
"This looks like a lot but it's a mixture of regression fixes as well
as fixes for longer standing issues.
1) Fix on-channel cancellation in mac80211, from Johannes Berg.
2) Handle CHECKSUM_COMPLETE properly in xt_TCPMSS netfilter xtables
module, from Eric Dumazet.
3) Avoid infinite loop in UDP SO_REUSEPORT logic, also from Eric
Dumazet.
4) Avoid a NULL deref if we try to set SO_REUSEPORT after a socket is
bound, from Craig Gallek.
5) GRO key comparisons don't take lightweight tunnels into account,
from Jesse Gross.
6) Fix struct pid leak via SCM credentials in AF_UNIX, from Eric
Dumazet.
7) We need to set the rtnl_link_ops of ipv6 SIT tunnels before we
register them, otherwise the NEWLINK netlink message is missing
the proper attributes. From Thadeu Lima de Souza Cascardo.
8) Several Spectrum chip bug fixes for mlxsw switch driver, from Ido
Schimmel
9) Handle fragments properly in ipv4 easly socket demux, from Eric
Dumazet.
10) Don't ignore the ifindex key specifier on ipv6 output route
lookups, from Paolo Abeni"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (128 commits)
tcp: avoid cwnd undo after receiving ECN
irda: fix a potential use-after-free in ircomm_param_request
net: tg3: avoid uninitialized variable warning
net: nb8800: avoid uninitialized variable warning
net: vxge: avoid unused function warnings
net: bgmac: clarify CONFIG_BCMA dependency
net: hp100: remove unnecessary #ifdefs
net: davinci_cpdma: use dma_addr_t for DMA address
ipv6/udp: use sticky pktinfo egress ifindex on connect()
ipv6: enforce flowi6_oif usage in ip6_dst_lookup_tail()
netlink: not trim skb for mmaped socket when dump
vxlan: fix a out of bounds access in __vxlan_find_mac
net: dsa: mv88e6xxx: fix port VLAN maps
fib_trie: Fix shift by 32 in fib_table_lookup
net: moxart: use correct accessors for DMA memory
ipv4: ipconfig: avoid unused ic_proto_used symbol
bnxt_en: Fix crash in bnxt_free_tx_skbs() during tx timeout.
bnxt_en: Exclude rx_drop_pkts hw counter from the stack's rx_dropped counter.
bnxt_en: Ring free response from close path should use completion ring
net_sched: drr: check for NULL pointer in drr_dequeue
...
The tg3_set_eeprom() function correctly initializes the 'start' variable,
but gcc generates a false warning:
drivers/net/ethernet/broadcom/tg3.c: In function 'tg3_set_eeprom':
drivers/net/ethernet/broadcom/tg3.c:12057:4: warning: 'start' may be used uninitialized in this function [-Wmaybe-uninitialized]
I have not come up with a way to restructure the code in a way that
avoids the warning without making it less readable, so this adds an
initialization for the declaration to shut up that warning.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The nb8800_poll() function initializes the 'next' variable in the
loop looking for new input data. We know this will be called at
least once because 'budget' is a guaranteed to be a positive number
when we enter the function, but the compiler doesn't know that
and warns when the variable is used later:
drivers/net/ethernet/aurora/nb8800.c: In function 'nb8800_poll':
drivers/net/ethernet/aurora/nb8800.c:350:21: warning: 'next' may be used uninitialized in this function [-Wmaybe-uninitialized]
Changing the 'while() {}' loop to 'do {} while()' makes it obvious
to the compiler what is going on so it no longer warns.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Mans Rullgard <mans@mansr.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When CONFIG_PCI_MSI is disabled, we get warnings about unused functions
in the vxge driver:
drivers/net/ethernet/neterion/vxge/vxge-main.c:2121:13: warning: 'adaptive_coalesce_tx_interrupts' defined but not used [-Wunused-function]
drivers/net/ethernet/neterion/vxge/vxge-main.c:2149:13: warning: 'adaptive_coalesce_rx_interrupts' defined but not used [-Wunused-function]
We could add another #ifdef here, but it's nicer to avoid those warnings
for good by converting the existing #ifdef to if(IS_ENABLED()), which has
the same effect but provides better compile-time coverage in general,
and lets the compiler understand better when the function is intentionally
unused.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The bgmac driver depends on BCMA_HOST_SOC, which is only used
when CONFIG_BCMA is enabled. However, it is a bool option and can
be set when CONFIG_BCMA=m, and then bgmac can be built-in, leading
to an obvious link error:
drivers/built-in.o: In function `bgmac_init':
:(.init.text+0x7f2c): undefined reference to `__bcma_driver_register'
drivers/built-in.o: In function `bgmac_exit':
:(.exit.text+0x110a): undefined reference to `bcma_driver_unregister'
To avoid this case, we need to depend on both BCMA and BCMA_SOC,
as this patch does. I'm also trying to make the dependency more
readable by splitting it into three lines, and adding a COMPILE_TEST
alternative so we can test-build it in all configurations that
support BCMA.
The added dependency on FIXED_PHY addresses a related issue where
we cannot call fixed_phy_register() when CONFIG_FIXED_PHY=m and
CONFIG_BGMAC=y.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Building the hp100 ethernet driver causes warnings when both the PCI
and EISA drivers are disabled:
ethernet/hp/hp100.c: In function 'hp100_module_init':
ethernet/hp/hp100.c:3047:2: warning: label 'out3' defined but not used [-Wunused-label]
ethernet/hp/hp100.c: At top level:
ethernet/hp/hp100.c:2828:13: warning: 'cleanup_dev' defined but not used [-Wunused-function]
We can easily avoid the warnings and make the driver look slightly
nicer by removing the #ifdefs that check for the CONFIG_PCI and
CONFIG_EISA, as all the registration functions are designed to
have no effect when the buses are disabled.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The davinci_cpdma mixes up physical addresses as seen from the CPU
and DMA addresses as seen from a DMA master, since it can operate
on both normal memory or an on-chip buffer. If dma_addr_t is
different from phys_addr_t, this means we get a compile-time warning
about the type mismatch:
ethernet/ti/davinci_cpdma.c: In function 'cpdma_desc_pool_create':
ethernet/ti/davinci_cpdma.c:182:48: error: passing argument 3 of 'dma_alloc_coherent' from incompatible pointer type [-Werror=incompatible-pointer-types]
pool->cpumap = dma_alloc_coherent(dev, size, &pool->phys,
In file included from ethernet/ti/davinci_cpdma.c:21:0:
dma-mapping.h:398:21: note: expected 'dma_addr_t * {aka long long unsigned int *}' but argument is of type 'phys_addr_t * {aka unsigned int *}'
static inline void *dma_alloc_coherent(struct device *dev, size_t size,
This slightly restructures the code so the address we use for
mapping RAM into a DMA address is always a dma_addr_t, avoiding
the warning. The code is correct even if both types are 32-bit
because the DMA master in this device only supports 32-bit addressing
anyway, independent of the types that are used.
We still assign this value to pool->phys, and that is wrong if
the driver is ever used with an IOMMU, but that value appears to
be never used, so there is no problem really. I've added a couple
of comments about where we do things that are slightly violating
the API.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
* Fix support for 3168 device:
* NVM version
* firmware file name
* device IDs
* Fix a compilation warning in dvm calibration code
* Fix the TPC (reduced Tx Power) code. This fixes performance issues
* Add device IDs for 8265
rtx2x00
* fix monitor mode regression dating back to 4.1
brcmfmac
* fix sdio initialisation related crash
rtlwifi
* rtl8821ae: Fix 5G failure when EEPROM is incorrectly encoded
ath9k
* ignore eeprom magic mismatch on flash based devices
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJWqyRLAAoJEG4XJFUm622bRiAH/2s3rRrFik3LUDMMJWbLDoNa
5ofIUlQnYPiUzLrStGrrZ93jcqG0rAGLovxEMR3cuWuVIV43RKq2vu+RE97fu8nM
j0NkWtD/g3mHYPGTkJ6ItXbs7t7ghhV+kFHcuZGPaikjEb3pTMGaA7sslzvptcWB
vzsKym/wxcZCanLqgsyMnbjiwnja8jXH/WFg3Otp+Ki0EDzBeaV9XNX9xZHMf/Nf
7I7ffSdMrHFZ/XrvMpLB15SVo9yH+tAFwrMS1WWnKJvUqO8kJZWFdLKM3DcShMTi
Tz6mwy7geVaXlAKKoi7MxJh4PGzQewRBHTMdPKORnuKFwRAlbgD8PGT8+RlKDOg=
=REf0
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-for-davem-2016-01-29' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers
Kalle Valo says:
====================
iwlwifi
* Fix support for 3168 device:
* NVM version
* firmware file name
* device IDs
* Fix a compilation warning in dvm calibration code
* Fix the TPC (reduced Tx Power) code. This fixes performance issues
* Add device IDs for 8265
rtx2x00
* fix monitor mode regression dating back to 4.1
brcmfmac
* fix sdio initialisation related crash
rtlwifi
* rtl8821ae: Fix 5G failure when EEPROM is incorrectly encoded
ath9k
* ignore eeprom magic mismatch on flash based devices
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The size of all_zeros_mac is 6 byte, but eth_hash() will access the
8 byte, and KASan reported the below bug:
[ 8596.479031] BUG: KASan: out of bounds access in __vxlan_find_mac+0x24/0x100 at addr ffffffff841514c0
[ 8596.487647] Read of size 8 by task ip/52820
[ 8596.490818] Address belongs to variable all_zeros_mac+0x0/0x40
[ 8596.496051] CPU: 0 PID: 52820 Comm: ip Tainted: G WC 4.1.15 #1
[ 8596.503520] Hardware name: HP ProLiant DL380p Gen8, BIOS P70 02/10/2014
[ 8596.509365] ffffffff841514c0 ffff88007450f0b8 ffffffff822fa5e1 0000000000000032
[ 8596.516112] ffff88007450f150 ffff88007450f138 ffffffff812dd58c ffff88007450f1d8
[ 8596.522856] ffffffff81113b80 0000000000000282 0000000000000001 ffffffff8101ee4d
[ 8596.529599] Call Trace:
[ 8596.530858] [<ffffffff822fa5e1>] dump_stack+0x4f/0x7b
[ 8596.535080] [<ffffffff812dd58c>] kasan_report_error+0x3bc/0x3f0
[ 8596.540258] [<ffffffff81113b80>] ? __lock_acquire+0x90/0x2140
[ 8596.545245] [<ffffffff8101ee4d>] ? save_stack_trace+0x2d/0x80
[ 8596.550234] [<ffffffff812dda70>] kasan_report+0x40/0x50
[ 8596.554647] [<ffffffff81b211e4>] ? __vxlan_find_mac+0x24/0x100
[ 8596.559729] [<ffffffff812dc399>] __asan_load8+0x69/0xa0
[ 8596.564141] [<ffffffff81b211e4>] __vxlan_find_mac+0x24/0x100
[ 8596.569033] [<ffffffff81b2683d>] vxlan_fdb_create+0x9d/0x570
it can be fixed by enlarging the all_zeros_mac to 8 byte, although it is
harmless; eth_hash() will be called in other place with the memory which
is larger and equal to 8 byte.
Signed-off-by: Li RongQing <roy.qing.li@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently the port based VLAN maps should be configured to allow every
port to egress frames on all other ports, except themselves.
The debugfs interface shows that they are misconfigured. For instance, a
7-port switch has the following content in the related register 0x06:
GLOBAL GLOBAL2 SERDES 0 1 2 3 4 5 6
...
6: 1fa4 1f0f 4 7f 7e 7d 7c 7b 7a 79
...
This means that port 3 is allowed to talk to port 2-6, but cannot talk
to ports 0 and 1. With this fix, port 3 can correctly talk to all ports
except 3 itself:
GLOBAL GLOBAL2 SERDES 0 1 2 3 4 5 6
...
6: 1fa4 1f0f 4 7e 7d 7b 77 6f 5f 3f
...
Fixes: ede8098d0f ("net: dsa: mv88e6xxx: bridges do not need an FID")
Reported-by: Kevin Smith <kevin.smith@elecsyscorp.com>
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Kevin Smith <kevin.smith@elecsyscorp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The moxart ethernet driver confuses coherent DMA buffers with
MMIO registers.
moxart_ether.c: In function 'moxart_mac_setup_desc_ring':
moxart_ether.c:146:428: error: passing argument 1 of '__fswab32' makes integer from pointer without a cast [-Werror=int-conversion]
moxart_ether.c:74:39: warning: incorrect type in argument 3 (different address spaces)
moxart_ether.c:74:39: expected void *cpu_addr
moxart_ether.c:74:39: got void [noderef] <asn:2>*tx_desc_base
This leaves the basic logic alone and uses normal pointers for
the virtual address of the descriptor. As we cannot use readl/writel
to access them, we also introduce our own moxart_desc_read
moxart_desc_write helpers that perform the same endianess swap
as the original code, but without the address space conversion.
The barriers are made explicit here where needed: Even in the worst-case
scenario, we just have to use a rmb() after checking ownership so
we don't read any input data before we are sure it is value, and we
use wmb() before transferring ownership back to the device.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ring index j is not wrapped properly at the end of the ring, causing
it to reference pointers past the end of the ring. For proper loop
termination and to access the ring properly, we need to increment j and
mask it before referencing the ring entry.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This hardware counter is misleading as it counts dropped packets that
don't match the hardware filters for unicast/broadcast/multicast. We
will still report this counter in ethtool -S for diagnostics purposes.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use completion ring for ring free response from firmware. The response
will be the last entry in the ring and we can free the ring after getting
the response. This will guarantee no spurious DMA to freed memory.
Signed-off-by: Prashant Sreedharan <prashant@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently when a macvlan is being initialized and the lower device is
netif_carrier_ok(), the macvlan device doesn't run through
rfc2863_policy() and is left with UNKNOWN operstate. Fix it by adding an
unconditional linkwatch event for the new macvlan device. Similar fix is
already used by the 8021q device (see register_vlan_dev()). Also fix the
inconsistent state when the lower device has been down and its carrier
was changed (when a device is down NETDEV_CHANGE doesn't get generated).
The second issue can be seen f.e. when we have a macvlan on top of a 8021q
device which has been down and its real device has been changing carrier
states, after setting the 8021q device up, the macvlan device will have
the same carrier state as it was before even though the 8021q can now
have a different state.
Example for case 1:
4: eth2: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast
state UP mode DEFAULT group default qlen 1000
$ ip l add l eth2 macvl0 type macvlan
$ ip l set macvl0 up
$ ip l sh macvl0
72: macvl0@eth2: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc
noqueue state UNKNOWN mode DEFAULT group default
link/ether f6:0b:54:0a:9d:a3 brd ff:ff:ff:ff:ff:ff
Example for case 2 (order is important):
Prestate: eth2 UP/CARRIER, vlan1 down, vlan1-macvlan down
$ ip l set vlan1-macvlan up
$ ip l sh vlan1-macvlan
71: vlan1-macvlan@vlan1: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500
qdisc noqueue state UNKNOWN mode DEFAULT group default
link/ether 4a:b8:44:56:b9:b9 brd ff:ff:ff:ff:ff:ff
[ eth2 loses CARRIER before vlan1 has been UP-ed ]
$ ip l sh eth2
4: eth2: <NO-CARRIER,BROADCAST,MULTICAST,UP> mtu 1500 qdisc pfifo_fast
state DOWN mode DEFAULT group default qlen 1000
link/ether 52:54:00:bf:57:16 brd ff:ff:ff:ff:ff:ff
$ ip l sh vlan1-macvlan
71: vlan1-macvlan@vlan1: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500
qdisc noqueue state UNKNOWN mode DEFAULT group default
link/ether 4a:b8:44:56:b9:b9 brd ff:ff:ff:ff:ff:ff
$ ip l set vlan1 up
$ ip l sh vlan1
70: vlan1@eth2: <NO-CARRIER,BROADCAST,MULTICAST,UP> mtu 1500 qdisc
noqueue state LOWERLAYERDOWN mode DEFAULT group default qlen 1000
link/ether 52:54:00:bf:57:16 brd ff:ff:ff:ff:ff:ff
$ ip l sh vlan1-macvlan
71: vlan1-macvlan@vlan1: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500
qdisc noqueue state UNKNOWN mode DEFAULT group default
link/ether 4a:b8:44:56:b9:b9 brd ff:ff:ff:ff:ff:ff
vlan1-macvlan is still UP, still has carrier and is still in the same
operstate as before. After the patch in case 1 macvl0 has state UP as it
should and in case 2 vlan1-macvlan has state LOWERLAYERDOWN again as it
should. Note that while the lower macvlan device is down their carrier
and thus operstate can go out of sync but that will be fixed once the
lower device goes up again.
This behaviour seems to have been present since beginning of git history.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert the driver to use ns_to_timespec64() to keep consistency
with timespec64_to_ns() instead of open coding the same logic.
Signed-off-by: Kefeng Wang <wangkefeng.wang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Throttle TX path only at slower than SuperSpeed USB.
SuperSpeed USB has enough bandwidth to maintain GigE.
Signed-off-by: Woojung Huh <woojung.huh@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Depends on chip, some EEPROM pins are muxed with LED function.
Disable & restore LED function to access EEPROM.
Signed-off-by: Woojung Huh <woojung.huh@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Update lan78xx to use patch of commit 4f2aaf7dd9
("Merge branch 'fix-phy-ignore-interrupts'").
Signed-off-by: Woojung Huh <woojung.huh@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When switchdev drivers process FDB notifications from the underlying
device they resolve the netdev to which the entry points to and notify
the bridge using the switchdev notifier.
However, since the RTNL mutex is not held there is nothing preventing
the netdev from disappearing in the middle, which will cause
br_switchdev_event() to dereference a non-existing netdev.
Make switchdev drivers hold the lock at the beginning of the
notification processing session and release it once it ends, after
notifying the bridge.
Also, remove switchdev_mutex and fdb_lock, as they are no longer needed
when RTNL mutex is held.
Fixes: 03bf0c2812 ("switchdev: introduce switchdev notifier")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Trying to batch Tx response events results in poor performance because
this delays freeing the transmitted skbs.
Instead use the standard RING_FINAL_CHECK_FOR_RESPONSES() macro to be
notified once the next Tx response is placed on the ring.
Signed-off-by: Malcolm Crossley <malcolm.crossley@citrix.com>
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The code in txq_put_data() would use txq->tx_curr_desc to index the
tso_hdrs/tso_hdrs_dma buffers, for less than 8 bytes unaligned
fragments, which is already moved to the next descriptor at the
beginning of the function.
If that fragment was the last of the the skb, the next skb would use
that same space to place the ip headers, overwritting that small
fragment data.
Fixes: 91986fd3d3 (net: mv643xx_eth: Ensure proper data alignment in TSO TX path)
Signed-off-by: Nicolas Schichan <nschichan@freebox.fr>
Reviewed-by: Philipp Kirchhofer <philipp@familie-kirchhofer.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
* make regulatory messages much less verbose by default
* various remain-on-channel fixes
* scheduled scanning fixes with hardware restart
* a PS-Poll handling fix; was broken just recently
* bugfix to avoid buffering non-bufferable MMPDUs
* world regulatory domain data fix
* a fix for scanning causing other work to get stuck
* hwsim: revert an older problematic patch that caused some
userspace tools to have issues - not that big a deal as
it's a debug only driver though
-----BEGIN PGP SIGNATURE-----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=6M7a
-----END PGP SIGNATURE-----
Merge tag 'mac80211-for-davem-2016-01-26' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211
Johannes Berg says:
====================
Here's a first set of fixes for the 4.5-rc cycle:
* make regulatory messages much less verbose by default
* various remain-on-channel fixes
* scheduled scanning fixes with hardware restart
* a PS-Poll handling fix; was broken just recently
* bugfix to avoid buffering non-bufferable MMPDUs
* world regulatory domain data fix
* a fix for scanning causing other work to get stuck
* hwsim: revert an older problematic patch that caused some
userspace tools to have issues - not that big a deal as
it's a debug only driver though
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Not every arch has io memory.
So, unbreak the build by fixing the dependencies.
Signed-off-by: Richard Weinberger <richard@nod.at>
Signed-off-by: David S. Miller <davem@davemloft.net>
The rx_lane, tx_lane and module fields in the PMLP register don't have
an additional offset besides the base one (0x04), so set it to 0x00.
Fixes: 4ec14b7634 ("mlxsw: Add interface to access registers and process events")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When dumping the FDB we can't compare the actual pointers of the ports
structs, as it's possible the struct represents a vPort instead of the
underlying physical port.
Solve this by comparing the local port number instead, as it's shared
between the physical ports and all the vPorts on top of him.
Fixes: 54a732018d ("mlxsw: spectrum: Adjust switchdev ops for VLAN devices")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
LAG FDB records can only point to LAG devices or VLAN devices configured
on top of them. Therefore, when dumping the FDB we shouldn't associate
these records with the underlying physical ports.
Fixes: 8a1ab5d766 ("mlxsw: spectrum: Implement FDB add/remove/dump for LAG")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
LAG FDB entries pointing to VLAN devices should be reported to the
bridge with the matching VLAN device and not the underlying LAG device.
Fixes: aac78a4408 ("mlxsw: spectrum: Adjust FDB notifications for VLAN devices")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When dumping the hardware FDB we should report entries pointing to VLAN
devices with VLAN 0, as packets coming into the bridge are untagged.
Likewise, pass FDB_{ADD,DEL} notifications with VLAN 0 for these
devices.
Fixes: 54a732018d ("mlxsw: spectrum: Adjust switchdev ops for VLAN devices")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When we disable learning on bridge port we should still update the
software bridge's FDB when entry pointing to this bridge port is
aged-out. We can otherwise have an inconsistency between software and
hardware tables.
Fixes: 8a1ab5d766 ("mlxsw: spectrum: Implement FDB add/remove/dump for LAG")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When port is put into LISTENING state it shouldn't populate the FDB, so
set the port's STP state in hardware to DISCARDING instead of LEARNING.
It will therefore keep listening to BPDU packets, but discard other
non-control packets and won't perform any learning.
Fixes: 56ade8fe3f ("mlxsw: spectrum: Add initial support for Spectrum ASIC")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When STP state is set to DISABLED the port is assumed to be inactive, but
currently we forward packets ingressing through it.
Instead, set the port's STP state in hardware to DISCARDING, which means
it doesn't forward packets or perform any learning, but it does trap
control packets. However, these packets will be dropped by bridge code,
which results in the expected behavior.
Fixes: 56ade8fe3f ("mlxsw: spectrum: Add initial support for Spectrum ASIC")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As explained in previous commit, we should always take care of flushing
the FDB in the driver and not rely on bridge code.
We need to distinguish between two cases with regards to LAG:
1) Port is leaving LAG while LAG is bridged (or VLAN devices on top of
it). In this case don't flush the FDB entries pointing to the LAG ID, as
this will affect other ports still member in the LAG. Only flush the FDB
when the last port in the LAG is leaving the bridge.
2) LAG device is leaving the bridge. In this case the CHANGEUPPER event
is simply propagated to each member port, so make each port flush the
FDB in its turn.
Note that emptying a bridged LAG from ports creates an inconsistency
between hardware and software. A user who later (< ageing_time)
re-populates the LAG won't have any FDB entries pointing to the LAG ID
in hardware, but they will be present in the software bridge's FDB.
Currently there is no good solution to this problem, but this will be
addressed by us in the future.
In order to optimize the flushing process, flush by port or LAG ID if
there are no VLAN interfaces on top of the port. Otherwise, flush using
(Port / LAG ID, FID=VID} for each of the lower 4K FIDs. In the case of
VLAN device simply flush using {Port / LAG ID, vFID} with the vFID to
which the VLAN device is mapped to.
Fixes: 56ade8fe3f ("mlxsw: spectrum: Add initial support for Spectrum ASIC")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When removing a net device from a bridge we should flush the FDB entries
associated with this net device. Up until now, we relied upon bridge
code to do that for us, but it is possible for user to prevent hardware
from syncing with the software bridge (learning_sync=0), so we need to
flush overselves.
Add the Switch Filtering DB Flush (SFDF) register that is used to flush
FDB entries according to different parameters (per-port, per-FID etc).
Fixes: 56ade8fe3f ("mlxsw: spectrum: Add initial support for Spectrum ASIC")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It is possible for a user to remove a port from a LAG device, while the
LAG device or VLAN devices on top of it are bridged. In these cases,
bridge's teardown sequence is never issued, so we need to take care of
it ourselves.
When LAG's unlinking event is received by port netdev:
1) Traverse its vPorts list and make those member in a bridge leave it.
They will be deleted later by LAG code.
2) Make the port netdev itself leave its bridge if member in one.
Fixes: 0d65fc1304 ("mlxsw: spectrum: Implement LAG port join/leave")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
FW behaviour changed and now updates driver about the used TPC
reduction in the following cases:
1. In tx response, which is used mostly for a single frame case
2. In BA notification
When tx aggregation fails with the initial rate, FW will send
to the driver BA notification and will try to transmit with the
next rate, but this time without tx power reduction. Thus, in case
of a failure with the initial rate, driver will get two BA notifications,
the first one with reduced tx power as in the LQ command and the second
one with 0 power reduction.
This patch adapts the TPC statistics according to the description above:
1. Use BA notifications instead of Tx response
2. For TPC only, drop the optimization which considers empty BA as one
MPDU. The reason is that with TPC we want to recover very quickly from
a bad power reduction and, therefore we'd like the success ratio to get
an immediate hit when failing to get a BA, so we'd switch back to a
lower or zero power reduction
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Update the struct which defines the support for 3168 cards.
Now it will search for a firmware of this format:
iwlwifi-3168-XX.ucode
Also, set the minimum version of the ucode to 20.
Update the minimum NVM version and minimum NVM calibrations
version of the 3168 series.
Signed-off-by: Oren Givon <oren.givon@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
intel/i40e/i40e_txrx.c: In function 'i40e_xmit_frame_ring':
intel/i40e/i40e_txrx.c:2367:20: error: 'oiph' may be used uninitialized in this function [-Werror=maybe-uninitialized]
intel/i40e/i40e_txrx.c:2317:16: note: 'oiph' was declared here
intel/i40e/i40e_txrx.c:2367:17: error: 'oudph' may be used uninitialized in this function [-Werror=maybe-uninitialized]
intel/i40e/i40e_txrx.c:2316:17: note: 'oudph' was declared here
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Fixes following build warnings :
drivers/net/ethernet/intel/i40e/i40e_main.c:7057:13: warning:
'i40e_sync_udp_filters_subtask' defined but not used [-Wunused-function]
drivers/net/ethernet/intel/i40e/i40e_main.c:8524:13: warning:
'i40e_add_vxlan_port' defined but not used [-Wunused-function]
drivers/net/ethernet/intel/i40e/i40e_main.c:8569:13: warning:
'i40e_del_vxlan_port' defined but not used [-Wunused-function]
drivers/net/ethernet/intel/i40e/i40e_main.c:8604:13: warning:
'i40e_add_geneve_port' defined but not used [-Wunused-function]
drivers/net/ethernet/intel/i40e/i40e_main.c:8651:13: warning:
'i40e_del_geneve_port' defined but not used [-Wunused-function]
Fixes: 6a89902405 ("i40e: geneve tunnel offload support")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Since eliminating send_completion_tid from struct hv_netvsc_packet, we
haven't add proper book keeping for the skb of the batched packet. This
patch fixes this issue and allows the previous skb is properly freed.
Otherwise, a panic may happen.
Thanks to Simon Xiao <sixiao@microsoft.com> for bisecting and analysis.
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Reviewed-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Recent changes to 'struct flow_keys' (e.g commit d34af823ff ("net: Add
VLAN ID to flow_keys")) introduced a performance regression in netvsc
driver. Is problem is, however, not the above mentioned commit but the
fact that netvsc_set_hash() function did some assumptions on the struct
flow_keys data layout and this is wrong.
Get rid of netvsc_set_hash() by switching to skb_get_hash(). This change
will also imply switching to Jenkins hash from the currently used Toeplitz
but it seems there is no good excuse for Toeplitz to stay.
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As Arnd Bergmann points out, using CONFIG_ARCH_MXC and/or SOC_IMX28
is wrong if some other ARM platform uses this device - the operation
of the driver would depend on an unrelated ARM platform that might
or might not be set for multi-platform kernels.
Prior to my previous patch, any other platforms using it would have
been broken already due to having the cbd_datlen/cbd_sc fields in
the wrong order, but byte ordering correctly, so no such platforms
can exist and work today.
In any case, it seems likely that only Freescale SoCs use this part,
and those are little-endian on ARM, so CONFIG_ARM is safe for them.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
We are getting many build warnings about:
'bar_start' may be used uninitialized
and
'bar_len' may be used uninitialized
They are not actually uninitialized as dfx_get_bars() will initialize
them properly. But still lets have them initialized just to satisfy the
compiler (gcc 4.8.2).
Signed-off-by: Sudip Mukherjee <sudip@vectorindia.org>
Acked-by: Maciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
We are getting build warning about:
macb.c:2889:13: warning: 'tx_clk' may be used uninitialized in this function
macb.c:2888:11: warning: 'hclk' may be used uninitialized in this function
In reality they are not used uninitialized as clk_init() will initialize
them, this patch will just silence the warning.
Signed-off-by: Sudip Mukherjee <sudip@vectorindia.org>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver treats the device descriptors as CPU-endian, which appears
to be correct with the default endianness on both ARM (typically LE)
and PowerPC (typically BE) SoCs, indicating that the hardware block
is generated differently. Add endianness annotations and byteswaps as
necessary.
It's not clear that the ifdef there really is correct and shouldn't
just be #ifdef CONFIG_ARM, but I also can't test on anything but the
i.MX6 HummingBoard where this gets it working with a BE kernel.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since commit 76e398a627 ("net: dsa: use switchdev obj for VLAN add/del
ops"), the Marvell 88E6xxx switch has been unable to pass traffic
between ports - any received traffic is discarded by the switch.
Taking a port out of bridge mode and configuring a vlan on it also the
port to start passing traffic.
With the debugfs files re-instated to allow debug of this issue by
comparing the register settings between the working and non-working
case, the reason becomes clear:
GLOBAL GLOBAL2 SERDES 0 1 2 3 4 5 6
- 7: 1111 707f 2001 2 2 2 2 2 0 2
+ 7: 1111 707f 2001 1 1 1 1 1 0 1
Register 7 for the ports is the default vlan tag register, and in the
non-working setup, it has been set to 2, despite vlan 2 not being
configured. This causes the switch to drop all packets coming in to
these ports. The working setup has the default vlan tag register set
to 1, which is the default vlan when none is configured.
Inspection of the code reveals why. The code prior to this commit
was:
- for (vid = vlan->vid_begin; vid <= vlan->vid_end; ++vid) {
...
- if (!err && vlan->flags & BRIDGE_VLAN_INFO_PVID)
- err = ds->drv->port_pvid_set(ds, p->port, vid);
but the new code is:
+ for (vid = vlan->vid_begin; vid <= vlan->vid_end; ++vid) {
...
+ }
...
+ if (pvid)
+ err = _mv88e6xxx_port_pvid_set(ds, port, vid);
This causes the new code to always set the default vlan to one higher
than the old code.
Fix this.
Fixes: 76e398a627 ("net: dsa: use switchdev obj for VLAN add/del ops")
Cc: <stable@vger.kernel.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is an additional patch to the one already submitted recently.
The previous patch was not complete, and the FCC port lock-up scenario
has been reproduced in lab.
I had an opportunity to check the current patch in lab and the FCC
port lock no longer freezes, while the previous patch still locks-up the
FCC port.
The current patch fixes a pointer arithmetic bug (second bug in the same
line), which leads FCC port lock-up during underrun/collision handling.
Within the tx_startup() function in mac-fcc.c, the address of last BD is
not calculated correctly. As a result of wrong calculation of the last BD
address, the next transmitted BD may be set to an area out of the transmit
BD ring. This actually causes to port lock-up and it is not recoverable.
Signed-off-by: Martin Roth <martin.roth@motorolasolutions.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Many AR913x based devices (maybe others too) do not have a valid EEPROM
magic in their calibration data partition.
Fixes: 6fa658fd5a ("ath9k: Simplify and fix eeprom endianness swapping")
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Acked-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Linus Torvalds
Arnd Bergmann
David S. Miller
Li RongQing
Vivien Didelot
Michael Chan
Prashant Sreedharan
Nikolay Aleksandrov
Kefeng Wang
Woojung.Huh@microchip.com
Ido Schimmel
Malcolm Crossley
Nicolas Schichan
Richard Weinberger
Kalle Valo
Gregory Greenman
Oren Givon
Eric Dumazet
Haiyang Zhang
Vitaly Kuznetsov
Johannes Berg
Sudip Mukherjee
Russell King
Martin Roth
Felix Fietkau