remove Frank Blaschka as S390 NETWORK DRIVERS maintainer
Acked-by: Frank Blaschka <blaschka@linux.vnet.ibm.com>
Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adjusts two instances where we were using the (too big)
struct qeth_ipacmd_setadpparms size instead of the commands' actual
size. This didn't do any harm, but wasted a few bytes.
Signed-off-by: Stefan Raspl <raspl@linux.vnet.ibm.com>
Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
claw devices are outdated and no longer supported.
This patch removes the claw driver.
Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
tcp_fastopen_create_child() is static and should not be exported.
tcp4_gso_segment() and tcp6_gso_segment() should be static.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds support for reporting the actual and maximum combined channels
count of the hv_netvsc driver via 'ethtool --show-channels'.
This required adding 'max_chn' to 'struct netvsc_device', and assigning
it 'rsscap.num_recv_que' in 'rndis_filter_device_add'. Now we can access
the combined maximum channel count via 'struct netvsc_device' in the
ethtool callback.
Signed-off-by: Andrew Schwartzmeyer <andrew@schwartzmeyer.com>
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet says:
====================
tcp: tso improvements
This patch serie reworks tcp_tso_should_defer() a bit
to get less bursts, and better ECN behavior.
We also removed tso_deferred field in tcp socket.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Another TCP issue is triggered by ECN.
Under pressure, receiver gets ECN marks, and send back ACK packets
with ECE TCP flag. Senders enter CA_CWR state.
In this state, tcp_tso_should_defer() is short cut :
if (icsk->icsk_ca_state != TCP_CA_Open)
goto send_now;
This means that about all ACK packets we receive are triggering
a partial send, and because cwnd is kept small, we can only send
a small amount of data for each incoming ACK,
which in return generate more ACK packets.
Allowing CA_Open and CA_CWR states to enable TSO defer in
tcp_tso_should_defer() brings performance back :
TSO autodefer has more chance to defer under pressure.
This patch increases TSO and LRO/GRO efficiency back to normal levels,
and does not impact overall ECN behavior.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With sysctl_tcp_min_tso_segs being 4, it is very possible
that tcp_tso_should_defer() decides not sending last 2 MSS
of initial window of 10 packets. This also applies if
autosizing decides to send X MSS per GSO packet, and cwnd
is not a multiple of X.
This patch implements an heuristic based on age of first
skb in write queue : If it was sent very recently (less than half srtt),
we can predict that no ACK packet will come in less than half rtt,
so deferring might cause an under utilization of our window.
This is visible on initial send (IW10) on web servers,
but more generally on some RPC, as the last part of the message
might need an extra RTT to get delivered.
Tested:
Ran following packetdrill test
// A simple server-side test that sends exactly an initial window (IW10)
// worth of packets.
`sysctl -e -q net.ipv4.tcp_min_tso_segs=4`
0.000 socket(..., SOCK_STREAM, IPPROTO_TCP) = 3
+0 setsockopt(3, SOL_SOCKET, SO_REUSEADDR, [1], 4) = 0
+0 bind(3, ..., ...) = 0
+0 listen(3, 1) = 0
+.1 < S 0:0(0) win 32792 <mss 1460,sackOK,nop,nop,nop,wscale 7>
+0 > S. 0:0(0) ack 1 <mss 1460,nop,nop,sackOK,nop,wscale 6>
+.1 < . 1:1(0) ack 1 win 257
+0 accept(3, ..., ...) = 4
+0 write(4, ..., 14600) = 14600
+0 > . 1:5841(5840) ack 1 win 457
+0 > . 5841:11681(5840) ack 1 win 457
// Following packet should be sent right now.
+0 > P. 11681:14601(2920) ack 1 win 457
+.1 < . 1:1(0) ack 14601 win 257
+0 close(4) = 0
+0 > F. 14601:14601(0) ack 1
+.1 < F. 1:1(0) ack 14602 win 257
+0 > . 14602:14602(0) ack 2
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
TSO relies on ability to defer sending a small amount of packets.
Heuristic is to wait for future ACKS in hope to send more packets at once.
Current algorithm uses a per socket tso_deferred field as a pseudo timer.
This pseudo timer relies on future ACK, but there is no guarantee
we receive them in time.
Fix would be to use a real timer, but cost of such timer is probably too
expensive for typical cases.
This patch changes the logic to test the time of last transmit,
because we should not add bursts of more than 1ms for any given flow.
We've used this patch for about two years at Google, before FQ/pacing
as it would reduce a fair amount of bursts.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently the usbnet core does not update the tx_packets statistic for
drivers with FLAG_MULTI_PACKET and there is no hook in the TX
completion path where they could do this.
cdc_ncm and dependent drivers are bumping tx_packets stat on the
transmit path while asix and sr9800 aren't updating it at all.
Add a packet count in struct skb_data so these drivers can fill it
in, initialise it to 1 for other drivers, and add the packet count
to the tx_packets statistic on completion.
Signed-off-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Tested-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Erik Hugne says:
====================
tipc: bug fix and some improvements
Most important is a fix for a nullptr exception that would occur when
name table subscriptions fail. The remaining patches are performance
improvements and cosmetic changes.
v2: remove unnecessary whitespace in patch #2
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
With the exception of infiniband media which does not use media
offsets, the media address is always located at offset 4 in the
media info field as defined by the protocol, so we move the
definition to the generic bearer.h
Signed-off-by: Erik Hugne <erik.hugne@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The TIPC_MEDIA_ADDR_SIZE and TIPC_MEDIA_ADDR_OFFSET names
are misleading, as they actually define the size and offset of
the whole media info field and not the address part. This patch
does not have any functional changes.
Signed-off-by: Erik Hugne <erik.hugne@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If a bearer is disabled by manual intervention, all links over that
bearer should be purged, indicated with the 'shutting_down' flag.
Otherwise tipc will get confused if a new bearer is enabled using
a different media type.
Signed-off-by: Erik Hugne <erik.hugne@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If a subscription request is sent to a topology server
connection, and any error occurs (malformed request, oom
or limit reached) while processing this request, TIPC should
terminate the subscriber connection. While doing so, it tries
to access fields in an already freed (or never allocated)
subscription element leading to a nullpointer exception.
We fix this by removing the subscr_terminate function and
terminate the connection immediately upon any subscription
failure.
Signed-off-by: Erik Hugne <erik.hugne@ericsson.com>
Reviewed-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The TIPC name distributor pushes topology updates to the cluster
neighbors. Currently this is done in a unicast manner, and the
skb holding the update is cloned for each cluster member. This
is unnecessary, as we only modify the destnode field in the header
so we change it to do pskb_copy instead.
Signed-off-by: Erik Hugne <erik.hugne@ericsson.com>
Reviewed-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch allows TSO being set/unset on the master, so that GSO
segmentation is done after team layer.
Similar patch is present for bonding:
b0ce3508b2 ("bonding: allow TSO being set on bonding master")
and bridge:
f902e8812e ("bridge: Add ability to enable TSO")
Suggested-by: Jiri Prochazka <jprochaz@redhat.com>
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
Alexander Duyck says:
====================
fib_trie: Remove leaf_info structure
This patch set removes the leaf_info structure from the IPv4 fib_trie. The
general idea is that the leaf_info structure itself only held about 6
actual bits of data, beyond that it was mostly just waste. As such we can
drop the structure, move the 1 byte representing the prefix/suffix length
into the fib_alias and just link it all into one list.
My testing shows that this saves somewhere between 4 to 10ns depending on
the type of test performed. I'm suspecting that this represents 1 to 2 L1
cache misses saved per look-up.
One side effect of this change is that semantic_match_miss will now only
increment once per leaf instead of once per leaf_info miss. However the
stat is already skewed now that we perform a preliminary check on the leaf
as a part of the look-up.
I also have gone through and addressed a number of ordering issues in the
first patch since I had misread the behavior of list_add_tail.
I have since run some additional testing and verified the resulting lists
are in the same order when combining multiple prefix length and tos values
in a single leaf.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
At this point the leaf_info hash is redundant. By adding the suffix length
to the fib_alias hash list we no longer have need of leaf_info as we can
determine the prefix length from fa_slen. So we can compress things by
dropping the leaf_info structure from fib_trie and instead directly connect
the leaves to the fib_alias hash list.
Signed-off-by: Alexander Duyck <alexander.h.duyck@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make use of an empty spot in the alias to store the suffix length so that
we don't need to pull that information from the leaf_info structure.
This patch also makes a slight change to the user statistics. Instead of
incrementing semantic_match_miss once per leaf_info miss we now just
increment it once per leaf if a match was not found.
Signed-off-by: Alexander Duyck <alexander.h.duyck@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This replaces the prefix length variable in the leaf_info structure with a
suffix length value, or host identifier length in bits. By doing this it
makes it easier to sort out since the tnodes and leaf are carrying this
value as well since it is compatible with the ->pos field in tnodes.
I also cleaned up one spot that had some list manipulation that could be
simplified. I basically updated it so that we just use hlist_add_head_rcu
instead of calling hlist_add_before_rcu on the first node in the list.
Signed-off-by: Alexander Duyck <alexander.h.duyck@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There isn't any advantage to having it as a list and by making it an hlist
we make the fib_alias more compatible with the list_info in terms of the
type of list used.
Signed-off-by: Alexander Duyck <alexander.h.duyck@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Madhu Challa says:
====================
Multicast group join/leave at ip level
This series enables configuring multicast group join/leave at ip level
by extending the "ip address" command.
It adds a new control socket mc_autojoin_sock and ifa_flag IFA_F_MCAUTOJOIN
to invoke the corresponding igmp group join/leave api.
Since the igmp group join/leave api takes the rtnl_lock the code had to
be refactored by adding a shim layer prefixed by __ that can be invoked
by code that already has the rtnl_lock. This way we avoid proliferation of
work queues.
The first patch in this series does the refactoring for igmp v6.
Its based on igmp v4 changes that were added by Eric Dumazet.
The second patch in this series does the group join/leave based on the
setting of the IFA_F_MCAUTOJOIN flag.
v5:
- addressed comments from Daniel Borkmann.
- removed blank line in patch 1/2
- removed unused variable, const arg in patch 2/2
v4:
- addressed comments from Yoshifuji Hideaki.
- Remove WARN_ON not needed because we return a value from v2.
- addressed comments from Daniel Borkmann.
- rename sock to mc_autojoin_sk
- ip_mc_config() pass ifa so it needs one less argument.
- igmp_net_{init|destroy}() use inet_ctl_sock_{create|destroy}
- inet_rtm_newaddr() change scope of ret.
- igmp_net_init() no need to initialize sock to NULL.
v3:
- addressed comments from David Miller.
- fixed indentation and local variable order.
v2:
- addressed comments from Eric Dumazet.
- removed workqueue and call __ip_mc_{join|leave}_group or
__ipv6_sock_mc_{join|drop}
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Joining multicast group on ethernet level via "ip maddr" command would
not work if we have an Ethernet switch that does igmp snooping since
the switch would not replicate multicast packets on ports that did not
have IGMP reports for the multicast addresses.
Linux vxlan interfaces created via "ip link add vxlan" have the group option
that enables then to do the required join.
By extending ip address command with option "autojoin" we can get similar
functionality for openvswitch vxlan interfaces as well as other tunneling
mechanisms that need to receive multicast traffic. The kernel code is
structured similar to how the vxlan driver does a group join / leave.
example:
ip address add 224.1.1.10/24 dev eth5 autojoin
ip address del 224.1.1.10/24 dev eth5
Signed-off-by: Madhu Challa <challa@noironetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Based on the igmp v4 changes from Eric Dumazet.
959d10f6bbf6("igmp: add __ip_mc_{join|leave}_group()")
These changes are needed to perform igmp v6 join/leave while
RTNL is held.
Make ipv6_sock_mc_join and ipv6_sock_mc_drop wrappers around
__ipv6_sock_mc_join and __ipv6_sock_mc_drop to avoid
proliferation of work queues.
Signed-off-by: Madhu Challa <challa@noironetworks.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the unlikely event that skb_get_hash is unable to deduce a hash
in udp_flow_src_port we use a consistent random value instead.
This is specified in GRE/UDP draft section 3.2.1:
https://tools.ietf.org/html/draft-ietf-tsvwg-gre-in-udp-encap-04
Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While testing I experience a deadlock while using the at86rf233 on a
raspberry pi. The reason was an edge triggered gpio irq because the irq
triggered while irq was disabled. This issue doesn't happend on a level
triggered irq because the irq will hit after calling enable_irq.
This patch adds a warning that it's not recommended to use a edge-triggered
irq type. Also change the examples to high-level irqtype.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The at86rf2xx chips supports the setting of irq polarity if active low
or active high. This patch adds a handling for IRQ_ACTIVE_LOW if the
irq_type is IRQ_TYPE_LEVEL_LOW.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Since we support at86rf233 we need to ensure that basic operation
default values are the same. This patch always sets IRQ_MASK_MODE to 0
which is after reset 1 at the at86rf233 and 0 at the at86rf231.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch removes tx_timeout handling. We used it in sync xmit
handling. Since we support async xmit handling a xmit timeout handling
isn't easy to implement and should be implemented by netdev watchdog
mechanism.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch adds support for setting the xtal trim register. Some at86rf2xx
transceiver boards needs fine tuning the xtal capacitor.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch copies the platform data in driver allocated space at first.
With this change we ensure that we access the allocated platform data as
readonly space.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Reported-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
gcc5 warns about passing a const array to hci_test_bit which takes a
non-const pointer:
net/bluetooth/hci_sock.c: In function ‘hci_sock_sendmsg’:
net/bluetooth/hci_sock.c:955:8: warning: passing argument 2 of ‘hci_test_bit’ discards ‘const’ qualifier from pointer target type [-Wdiscarded-array-qualifiers]
&hci_sec_filter.ocf_mask[ogf])) &&
^
net/bluetooth/hci_sock.c:49:19: note: expected ‘void *’ but argument is of type ‘const __u32 (*)[4] {aka const unsigned int (*)[4]}’
static inline int hci_test_bit(int nr, void *addr)
^
So make 'addr' 'const void *'.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Cc: Gustavo Padovan <gustavo@padovan.org>
Cc: Johan Hedberg <johan.hedberg@gmail.com>
The 'master' parameter of the New CSRK event was recently renamed to
'type', with the old values kept for backwards compatibility as
unauthenticated local/remote keys. This patch updates the code to take
into account the two new (authenticated) values and ensures they get
used based on the security level of the connection that the respective
keys get distributed over.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
my previous patch skipped vlan range optimizations during skb size
calculations for simplicity.
This incremental patch considers vlan ranges during
skb size calculations. This leads to a bit of code duplication
in the fill and size calculation functions. But, I could not find a
prettier way to do this. will take any suggestions.
Previously, I had reused the existing br_get_link_af_size size calculation
function to calculate skb size for notifications. Reusing it this time
around creates some change in behaviour issues for the usual
.get_link_af_size callback.
This patch adds a new br_get_link_af_size_filtered() function to
base the size calculation on the incoming filter flag and include
vlan ranges.
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Reviewed-by: Scott Feldman <sfeldma@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Scott Feldman says:
====================
rocker cleanups
Pushing out some rocker cleanups I've had in my queue for a while. Nothing
major, just some sync-up with changes that already went into device code
(hard-coding desc err return values and lport renaming). Also fixup
port fowarding transitions prompted by some DSA discussions about how to
restore port state when port leaves bridge.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Cleanup the port forwarding state transitions for the cases when the port
joins or leaves a bridge, or is brought admin UP or DOWN. When port is
bridged, we can rely on bridge driver putting port in correct state using
STP callback into port driver, regardless if bridge is enabled for STP or not.
When port is not bridged, we can reuse some of the STP code to enabled or
disable forwarding depending on UP or DOWN.
Tested by trying all the transitions from bridge/not bridge, and UP/DOWN, and
verifying port is in the correct forwarding state after each transition.
Signed-off-by: Scott Feldman <sfeldma@gmail.com>
Acked-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is just a rename of physical ports from "lport" to "pport". Not a
functional change. OF-DPA uses logical ports (lport) for tunnels, but the
driver (and device) were using "lport" for physical ports. Renaming physical
ports references to "pport", freeing up "lport" for use later with tunnels.
Signed-off-by: Scott Feldman <sfeldma@gmail.com>
Acked-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
The rocker device returns error codes if something goes wrong with descriptor
processing. Originally the device used standard errno codes for different
errors, but since those errno codes aren't portable across ARCHs, the device
now returns hard-coded error codes that stay constant across diff ARCHs. Fix
driver to use those same hard-coded values.
Signed-off-by: Scott Feldman <sfeldma@gmail.com>
Acked-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Kirsher says:
====================
Intel Wired LAN Driver Updates 2015-02-24
This series contains updates to i40e and i40evf only, which bumps their
versions to i40e 1.2.9 and i40evf 1.2.3.
Paul fixes i40e_debug_aq() for big endian machines by adding the
appropriate LExx_TO_CPU wrappers.
Catherine adds a requested speed variable to the link_status to store the
last speeds we requested from the firmware and use the advertised speed
settings in get_settings in ethtool now that we have it. Due to the
new code addition, she also refactors get_settings to improve readability
and to accommodate some of the longer lines of code by adding two
functions i40e_get_settings_link_up() and i40e_get_settings_link_down().
Carolyn adds a struct to the VSI struct to keep track of RXNFC settings
done via ethtool. Adds more information to the interrupt vector
names, specifically to the VF misc vector name so that we can distinguish
between all the interrupts.
Ashish enables the i40evf driver to enable debug prints via ethtool.
Mitch updates i40e to enable packet split only when IOMMU is in use,
since it shows a distinct advantage over the single-buffer path
because it minimizes DMA mapping and unmapping. Also adds the receive
routine in use to the features log message to be able to print the
receive packet split status.
Greg adds the ability to get, set and commit permanently the NPAR
partition BW configuration through configfs. Enables an application
to query the i40e driver's private flags to get the status of NPAR
enablement via ethtool.
Neerav adds support for bridge offload ndo_ops getlink and setlink
to enable bridge hardware mode as per the mode set via IFLA_BRIDGE_MODE.
The support is only enabled in the case of a PF VSI and not available for
any other VSI type.
Kevin fixes i40e by ensuring the BUF and FLAG_RD flags are set for
indirect admin queue command.
Vasu updates the driver to setup FCoE netdev device type as "fcoe", so that
it shows up in sysfs as FCoE device.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
To avoid race conditions when using the ds->ports[] array,
we need to check if the accessed port has been initialized.
Introduce and use helper function dsa_is_port_initialized
for that purpose and use it where needed.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Florian Fainelli says:
====================
net: dsa: integration with SWITCHDEV for HW bridging
This patch set provides the DSA and SWITCHDEV integration bits together and
modifies the bcm_sf2 driver accordingly such that it works properly with HW
bridging.
Changes in v3:
- add back the null pointer check in dsa_slave_br_port_mask from Guenter
- slightly rework patch 1 commit message not to mention the function name
we add in patch 2
Changes in v2:
- avoid a race condition in how DSA network devices are created, patch from
Guenter Roeck
- provide a consistent and work STP state once a port leaves the bridge
- retain a bridge device pointer to properly flag port/bridge membership
- properly flush the ARL (Address Resolution Logic) in bcm_sf2.c
- properly retain port membership when individually bringing devices up/down
while they are members of a bridge
We discussed on the mailing-list the possibility of standardizing a "fdb_flush"
operation for DSA switch drivers, looking at the Marvell and Broadcom switches,
I am not convinced this is practical or diserable as the terminologies vary
here, but there is nothing preventing us from doing it later.
Many thanks to Guenter and Andrew for both testing and providing feedback.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement the bridge join, leave and set_stp callbacks by making that
we do the following:
- when a port joins the bridge, all existing ports in the bridge get
their VLAN control register updated with that joining port
- the joining port is including all existing bridge ports in its own
VLAN control register
The leave operation is fairly similar, special care must be taken to
make sure that port leaving the bridging is not removing itself from its
own VLAN control register.
Since the various BR_* states apply directly to our HW semantics, we
just need to translate these constants into their corresponding HW
settings, and voila!
We make sure to trigger a fast-ageing process for ports that are
joining/leaving the bridge and transition from incompatible states, this
is equivalent to triggering an ARL flush for that port.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to support bridging offloads in DSA switch drivers, select
NET_SWITCHDEV to get access to the port_stp_update and parent_get_id
NDOs that we are required to implement.
To facilitate the integratation at the DSA driver level, we implement 3
types of operations:
- port_join_bridge
- port_leave_bridge
- port_stp_update
DSA will resolve which switch ports that are currently bridge port
members as some Switch hardware/drivers need to know about that to limit
the register programming to just the relevant registers (especially for
slow MDIO buses).
We also take care of setting the correct STP state when slave network
devices are brought up/down while being bridge members.
Finally, when a port is leaving the bridge, we make sure we set in
BR_STATE_FORWARDING state, otherwise the bridge layer would leave it
disabled as a result of having left the bridge.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
A network device notifier can be called for one or more of the created
slave devices before all slave devices have been registered. This can
result in a mismatch between ds->phys_port_mask and the registered devices
by the time the call is made, and it can result in a slave device being
added to a bridge before its entry in ds->ports[] has been initialized.
Rework the initialization code to initialize entries in ds->ports[] in
dsa_slave_create. With this change, dsa_slave_create no longer needs
to return slave_dev but can return an error code instead.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Bump i40e to 1.2.9 and i40evf 1.2.3
Also update the copyright year.
Change-ID: I345d777e94abd0acffe6a28793f675d251a86299
Signed-off-by: Sravanthi Tangeda <sravanthi.tangeda@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds the netdev name to the VF misc vector name. Without
this patch, all the interrupts show the same info, so it difficult to
distinguish them.
Change-ID: I247828697e1373ecfb5f8dc1bc9618e98a7f4942
Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Allow an application to query the i40e driver's private flags to get the
status of NPAR enablement. This will be used by applications to determine
if there are NPAR specific features available.
Change-ID: Ia6d9477a48f9c4cb41ca022bd433f77da3f2146c
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Set FLAG_RD for send_driver_version AQ command.
Change-ID: I8253051eff85a1d4b5a4e12ce0395b65ceb91e62
Signed-off-by: Kevin Scott <kevin.c.scott@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add the RX routine in use to the features log message.
Change-ID: Ifbbf28fb7f42b9a3d2828586488e9e6331107dd5
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Ursula Braun
Stefan Raspl
Eric Dumazet
Andrew Schwartzmeyer
David S. Miller
Ben Hutchings
Erik Hugne
Jiri Pirko
Alexander Duyck
Madhu Challa
Tom Herbert
Alexander Aring
Jiri Slaby
Johan Hedberg
Roopa Prabhu
Scott Feldman
Guenter Roeck
Florian Fainelli
Sravanthi Tangeda
Carolyn Wyborny
Greg Rose
Kevin Scott
Mitch Williams