This module specific flag can be made static as it does not need to be
in global scope.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Charles Chiou <charles.chiou@tw.promise.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
1. Add reboot notifier and register it in stex_probe for all supported
device.
2. For all supported device in restart flow, we get a callback from
notifier and set S6flag for stex_shutdown & stex_hba_stop to send
restart command to FW.
Signed-off-by: Charles.Chiou <charles.chiou@tw.promise.com>
Signed-off-by: Paul.Lyu <paul.lyu@tw.promise.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Pegasus series is a RAID support product using Thunderbolt technology.
The newest product, Pegasus 3(P3) supports Thunderbolt 3 technology with
a different chip.
1. Change driver version.
2. Add P3 VID, DID and define it's device address.
3. P3 use msi interrupt, so stex_request_irq P3 type enable msi.
4. For hibernation, use msi_lock in stex_ss_handshake to prevent msi
register write again when handshaking.
5. P3 doesn't need read() as flush.
6. In stex_ss_intr & stex_abort, P3 only clear interrupt register when
getting vendor defined interrupt.
Signed-off-by: Charles.Chiou <charles.chiou@tw.promise.com>
Signed-off-by: Paul.Lyu <paul.lyu@tw.promise.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add S3/S4 support, add .suspend and .resume function in pci_driver. In
.suspend handler, driver send S3/S4 signal to the device.
Signed-off-by: Charles Chiou <charles.chiou@tw.promise.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
1. Add hotplug support. Pegasus support surprise removal. To this end, I
use return_abnormal_state function to return DID_NO_CONNECT for all
commands which sent to driver.
2. Remove stex_hba_stop in stex_remove because we cannot send command to
device after hotplug.
3. Add new device status: MU_STATE_STOP, MU_STATE_NOCONNECT,
MU_STATE_STOP. MU_STATE_STOP is currently not referenced.
MU_STATE_NOCONNECT represent that device is plugged out from the
host.
4. Use return_abnormal_function() to substitute part of code in
stex_do_reset.
Signed-off-by: Charles Chiou <charles.chiou@tw.promise.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Pegasus is a high performace hardware RAID solution designed to unleash
the raw power of Thunderbolt technology.
1. Add code to distinct SuperTrack and Pegasus series by sub device ID.
It should support backward compatibility.
2. Change the driver version.
Signed-off-by: Charles Chiou <charles.chiou@tw.promise.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Function stex_gettime uses 'struct timeval' whose tv_sec value
will overflow on 32-bit systems in year 2038 and beyond. This patch
replaces the use of struct timeval and do_gettimeofday with
ktime_get_real_seconds, which returns a 64-bit seconds value.
Suggested-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Tina Ruchandani <ruchandani.tina@gmail.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
This patch changes the !blk-mq path to the same defaults as the blk-mq
I/O path by always enabling block tagging, and always using host wide
tags. We've had blk-mq available for a few releases so bugs with
this mode should have been ironed out, and this ensures we get better
coverage of over tagging setup over different configs.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Jens Axboe <axboe@kernel.dk>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
Now that we also get proper values in cmd->request->tag for untagged
commands, there is no need to force tagged_supported to on in drivers
that need host-wide tags.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Remove the tagged argument from scsi_adjust_queue_depth, and just let it
handle the queue depth. For most drivers those two are fairly separate,
given that most modern drivers don't care about the SCSI "tagged" status
of a command at all, and many old drivers allow queuing of multiple
untagged commands in the driver.
Instead we start out with the ->simple_tags flag set before calling
->slave_configure, which is how all drivers actually looking at
->simple_tags except for one worke anyway. The one other case looks
broken, but I've kept the behavior as-is for now.
Except for that we only change ->simple_tags from the ->change_queue_type,
and when rejecting a tag message in a single driver, so keeping this
churn out of scsi_adjust_queue_depth is a clear win.
Now that the usage of scsi_adjust_queue_depth is more obvious we can
also remove all the trivial instances in ->slave_alloc or ->slave_configure
that just set it to the cmd_per_lun default.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Allow a driver to ask for block layer tags by setting .use_blk_tags in the
host template, in which case it will always see a valid value in
request->tag, similar to the behavior when using blk-mq. This means even
SCSI "untagged" commands will now have a tag, which is especially useful
when using a host-wide tag map.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Calling scsi_print_command should not be necessary during abort;
if the information is required one should enable scsi logging.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Robert Elliott <elliott@hp.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Since commit 0998d06310
(device-core: Ensure drvdata = NULL when no driver is bound),
the driver core clears the driver data to NULL after device_release
or on probe failure. Thus, it is not needed to manually clear the
device driver data to NULL.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Cc: James Bottomley <JBottomley@parallels.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
CONFIG_HOTPLUG is going away as an option. As a result, the __dev*
markings need to be removed.
This change removes the use of __devinit, __devexit_p, __devinitdata,
__devinitconst, and __devexit from these drivers.
Based on patches originally written by Bill Pemberton, but redone by me
in order to handle some of the coding style issues better, by hand.
Cc: Bill Pemberton <wfp5p@virginia.edu>
Cc: Adam Radford <linuxraid@lsi.com>
Cc: "James E.J. Bottomley" <JBottomley@parallels.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Move the mid-layer's ->queuecommand() invocation from being locked
with the host lock to being unlocked to facilitate speeding up the
critical path for drivers who don't need this lock taken anyway.
The patch below presents a simple SCSI host lock push-down as an
equivalent transformation. No locking or other behavior should change
with this patch. All existing bugs and locking orders are preserved.
Additionally, add one parameter to queuecommand,
struct Scsi_Host *
and remove one parameter from queuecommand,
void (*done)(struct scsi_cmnd *)
Scsi_Host* is a convenient pointer that most host drivers need anyway,
and 'done' is redundant to struct scsi_cmnd->scsi_done.
Minimal code disturbance was attempted with this change. Most drivers
needed only two one-line modifications for their host lock push-down.
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Acked-by: James Bottomley <James.Bottomley@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
percpu.h is included by sched.h and module.h and thus ends up being
included when building most .c files. percpu.h includes slab.h which
in turn includes gfp.h making everything defined by the two files
universally available and complicating inclusion dependencies.
percpu.h -> slab.h dependency is about to be removed. Prepare for
this change by updating users of gfp and slab facilities include those
headers directly instead of assuming availability. As this conversion
needs to touch large number of source files, the following script is
used as the basis of conversion.
http://userweb.kernel.org/~tj/misc/slabh-sweep.py
The script does the followings.
* Scan files for gfp and slab usages and update includes such that
only the necessary includes are there. ie. if only gfp is used,
gfp.h, if slab is used, slab.h.
* When the script inserts a new include, it looks at the include
blocks and try to put the new include such that its order conforms
to its surrounding. It's put in the include block which contains
core kernel includes, in the same order that the rest are ordered -
alphabetical, Christmas tree, rev-Xmas-tree or at the end if there
doesn't seem to be any matching order.
* If the script can't find a place to put a new include (mostly
because the file doesn't have fitting include block), it prints out
an error message indicating which .h file needs to be added to the
file.
The conversion was done in the following steps.
1. The initial automatic conversion of all .c files updated slightly
over 4000 files, deleting around 700 includes and adding ~480 gfp.h
and ~3000 slab.h inclusions. The script emitted errors for ~400
files.
2. Each error was manually checked. Some didn't need the inclusion,
some needed manual addition while adding it to implementation .h or
embedding .c file was more appropriate for others. This step added
inclusions to around 150 files.
3. The script was run again and the output was compared to the edits
from #2 to make sure no file was left behind.
4. Several build tests were done and a couple of problems were fixed.
e.g. lib/decompress_*.c used malloc/free() wrappers around slab
APIs requiring slab.h to be added manually.
5. The script was run on all .h files but without automatically
editing them as sprinkling gfp.h and slab.h inclusions around .h
files could easily lead to inclusion dependency hell. Most gfp.h
inclusion directives were ignored as stuff from gfp.h was usually
wildly available and often used in preprocessor macros. Each
slab.h inclusion directive was examined and added manually as
necessary.
6. percpu.h was updated not to include slab.h.
7. Build test were done on the following configurations and failures
were fixed. CONFIG_GCOV_KERNEL was turned off for all tests (as my
distributed build env didn't work with gcov compiles) and a few
more options had to be turned off depending on archs to make things
build (like ipr on powerpc/64 which failed due to missing writeq).
* x86 and x86_64 UP and SMP allmodconfig and a custom test config.
* powerpc and powerpc64 SMP allmodconfig
* sparc and sparc64 SMP allmodconfig
* ia64 SMP allmodconfig
* s390 SMP allmodconfig
* alpha SMP allmodconfig
* um on x86_64 SMP allmodconfig
8. percpu.h modifications were reverted so that it could be applied as
a separate patch and serve as bisection point.
Given the fact that I had only a couple of failures from tests on step
6, I'm fairly confident about the coverage of this conversion patch.
If there is a breakage, it's likely to be something in one of the arch
headers which should be easily discoverable easily on most builds of
the specific arch.
Signed-off-by: Tejun Heo <tj@kernel.org>
Guess-its-ok-by: Christoph Lameter <cl@linux-foundation.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>
During a manual scan, a user can send command to a nonexistent
lun, precisely at the point of max_lun. Normally it's possible
(but not required) that the firmware has the knowledge that it
is an invalid lun. In the particular case when max_lun is 256,
however, the nonexistent lun 256 will be confused with lun 0,
because the lun member in a request message is only u8, and 256
will become 0. So we need to fix the problem, at least, at the
driver level.
Signed-off-by: Ed Lin <ed.lin@promise.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Add support for reset request from firmware for controllers
of st_shasta and st_yel type. Code adjustments necessary
for this change are also included.
Signed-off-by: Ed Lin <ed.lin@promise.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
The controllers of st_seq and st_vsc type can work
if only small dma buffer is available, with a reduced
firmware feature set. Add support for this case.
Signed-off-by: Ed Lin <ed.lin@promise.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Add reset related code for st_yel.
1. Set the SS_H2I_INT_RESET bit.
2. Wait for the SS_MU_OPERATIONAL flag. This is also part of
normal handshake process so move it to handshake routine.
3. Continue handshake with the firmware.
Signed-off-by: Ed Lin <ed.lin@promise.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Replace all DMA_32BIT_MASK macro with DMA_BIT_MASK(32)
Signed-off-by: Yang Hongyang<yanghy@cn.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Replace all DMA_64BIT_MASK macro with DMA_BIT_MASK(64)
Signed-off-by: Yang Hongyang<yanghy@cn.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This adds the support of a new SAS 6G controller (st_yel)
Signed-off-by: Ed Lin <ed.lin@promise.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Use config struct (st_card_info) for parameters of different controllers
Signed-off-by: Ed Lin <ed.lin@promise.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
This adds the MSI support (default 0=off)
Signed-off-by: Ed Lin <ed.lin@promise.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
These are some small code fixes and changes, including:
- use 64 bit when possible
- remove some unnecessary code (in interrupt, queuecommand routine etc.)
- code change for reset handler
Signed-off-by: Ed Lin <ed.lin@promise.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Some small fixes, including:
- add data direction in req_msg because new firmware version
may require this (backward compatible)
- change internal timeout value
- change judgment of type st_vsc1
- blank line handling, etc.
Signed-off-by: Ed Lin <ed.lin@promise.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
This is the fix for controller type st_yosemite, including
- max_lun is 256 (backward compatible)
- remove unneeded special handling of INQUIRY
- remove unnecessary listing of sub device ids
Signed-off-by: Ed Lin <ed.lin@promise.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Add new device id for controller type st_seq.
Signed-off-by: Ed Lin <ed.lin@promise.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
The interrupt routine is good for normal cases. However, if the firmware
is abnormal and returns an invalid response, the driver may reuse a
ccb structure that has already been handled. This may cause problem.
Fix this by setting the req member to NULL. Next time we know the
response is invalid and handle accordingly if req is NULL.
Signed-off-by: Ed Lin <ed.lin@promise.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Use the newly introduced pci_ioremap_bar() function in drivers/scsi.
pci_ioremap_bar() just takes a pci device and a bar number, with the goal
of making it really hard to get wrong, while also having a central place
to stick sanity checks.
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Acked-by: Matthew Wilcox <willy@linux.intel.com>
Cc: Brian King <brking@us.ibm.com>
Cc: Ed Lin <ed.lin@promise.com>
Cc: Nick Cheng <nick.cheng@areca.com.tw>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
stex sets the timeout in its slave configure routine for all devices.
This now needs to update the request queue timeout in block.
Cc: Ed Lin <ed.lin@promise.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
We want to set the queue depth to something reasonable - not
the can_queue.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Cc: Ed Lin <ed.lin@promise.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Acked-by: Ed Lin <ed.lin@promise.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
This replaces stex_internal_copy with scsi_sg_copy_to/from_buffer.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Acked-by: Ed Lin <ed.lin@promise.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
stex_internal_copy copies an in-kernel buffer to a sg list by using
scsi_kmap_atomic_sg. Some functions calls stex_internal_copy with
sg_count in struct st_ccb, which is the value that dma_map_sg
returned. However it might be shorter than the actual number of sg
entries (if the IOMMU merged the sg entries).
scsi_kmap_atomic_sg doesn't see sg->dma_length so stex_internal_copy
should be called with the actual number of sg entries
(i.e. scsi_sg_count), because if the sg entries were merged,
stex_direct_copy wrongly think that the data length in the sg list is
shorter than the actual length.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Acked-by: Ed Lin <ed.lin@promise.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
stex_direct_copy copies an in-kernel buffer to a sg list in order to
spoof some SCSI commands. stex_direct_copy calls dma_map_sg and then
stex_internal_copy with the value that dma_map_sg returned. It calls
scsi_kmap_atomic_sg to copy data.
scsi_kmap_atomic_sg doesn't see sg->dma_length so if dma_map_sg merges
sg entries, stex_internal_copy gets the smaller number of sg entries
than the acutual number, which means it wrongly think that the data
length in the sg list is shorter than the actual length.
stex_direct_copy shouldn't call dma_map_sg and it doesn't need since
this code path doesn't involve dma transfers. This patch removes
stex_direct_copy and simply calls stex_internal_copy with the actual
number of sg entries.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Acked-by: Ed Lin <ed.lin@promise.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
With the sg table code, every SCSI driver is now either chain capable
or broken (or has sg_tablesize set so chaining is never activated), so
there's no need to have a check in the host template.
Also tidy up the code by moving the scatterlist size defines into the
SCSI includes and permit the last entry of the scatterlist pools not
to be a power of two.
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
This option is true if a low-level driver can support sg
chaining. This will be removed eventually when all the drivers are
converted to support sg chaining. q->max_phys_segments is set to
SCSI_MAX_SG_SEGMENTS if false.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
The original implementation in stex_ys_commands() is inappropriate.
For xfer len information, we should use resid instead.
Signed-off-by: Ed Lin <ed.lin@promise.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Conflicts:
drivers/scsi/jazz_esp.c
Same changes made by both SCSI and SPARC trees: problem with UTF-8
conversion in the copyright.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
- remove the unnecessary map_single path.
- convert to use the new accessors for the sg lists and the
parameters.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Acked-by: Ed Lin <ed.lin@promise.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Add debug information into abort and host_reset routine.
Change ioremap to ioremap_nocache.
Version updated to 3.6.0000.1.
Signed-off-by: Ed Lin <ed.lin@promise.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
After reset completed, the scsi error handler sends out TEST_UNIT_READY
to the device. For 'normal' devices the command will be handled by firmware.
However, because the RAID console only interfaces to scsi mid layer, the
firmware will not process the command for it. This will make the console to
be offlined right after reset. Add the handling in driver to fix this problem.
Signed-off-by: Ed Lin <ed.lin@promise.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
During hard bus reset of st_shasta controllers, 1 ms is not enough for
16-port controllers, although it's good for 8-port controllers. Extend the
wait time to 100 ms to allow bus resets finish successfully.
Signed-off-by: Ed Lin <ed.lin@promise.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
The correct internal mapping of stex controllers should be:
id:0~15, lun:0~7 (st_shasta)
id:0, lun:0~127 (st_yosemite)
id:0~127, lun:0 (st_vsc and st_vsc1)
This patch reports the internal mapping to scsi mid layer, eliminating
the translation between scsi mid layer and firmware. To achieve this
goal, we also need to:
-- fail the REPORT_LUNS command for st_shasta because the
firmware is known to not report all actual luns
-- add an entry in scsi_devindo.c to force sequential lun scan
(for st_shasta controllers)
-- fail the REPORT_LUNS command for console device
-- remove special handling of REPORT_LUNS command for
st_yosemite, as there is no translation mapping now
Signed-off-by: Ed Lin <ed.lin@promise.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
After Al Viro (finally) succeeded in removing the sched.h #include in module.h
recently, it makes sense again to remove other superfluous sched.h includes.
There are quite a lot of files which include it but don't actually need
anything defined in there. Presumably these includes were once needed for
macros that used to live in sched.h, but moved to other header files in the
course of cleaning it up.
To ease the pain, this time I did not fiddle with any header files and only
removed #includes from .c-files, which tend to cause less trouble.
Compile tested against 2.6.20-rc2 and 2.6.20-rc2-mm2 (with offsets) on alpha,
arm, i386, ia64, mips, powerpc, and x86_64 with allnoconfig, defconfig,
allmodconfig, and allyesconfig as well as a few randconfigs on x86_64 and all
configs in arch/arm/configs on arm. I also checked that no new warnings were
introduced by the patch (actually, some warnings are removed that were emitted
by unnecessarily included header files).
Signed-off-by: Tim Schmielau <tim@physik3.uni-rostock.de>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Colin Ian King
Charles
Tina Ruchandani
Christoph Hellwig
Hannes Reinecke
Jingoo Han
Greg Kroah-Hartman
Jeff Garzik
Tejun Heo
Ed Lin
Yang Hongyang
Arjan van de Ven
James Bottomley
Mike Christie
FUJITA Tomonori
FUJITA Tomonori
James Bottomley
Tim Schmielau