Highlights:
- Microsoft Surface:
- SSAM hot unplug support
- Surface Pro 8 keyboard cover support
- Tablet mode switch support for Surface Pro 8 and Surface Laptop Studio
- thinkpad_acpi: AMD Automatice Mode Transitions (AMT) support
- Mellanox:
- Vulcan chassis COMe NVSwitch management support
- XH3000 support
- New generic/shared Intel P2SB (Primary to Sideband) support
- Lots of small cleanups
- Various small bugfixes
- Various new hardware ids / quirks additions
The following is an automated git shortlog grouped by driver:
ACPI:
- video: Fix acpi_video_handles_brightness_key_presses()
- video: Change how we determine if brightness key-presses are handled
Documentation/ABI:
- Add new attributes for mlxreg-io sysfs interfaces
- mlxreg-io: Fix contact info
Drop the PMC_ATOM Kconfig option:
- Drop the PMC_ATOM Kconfig option
EDAC, pnd2:
- convert to use common P2SB accessor
- Use proper I/O accessors and address space annotation
HID:
- surface-hid: Add support for hot-removal
ISST:
- PUNIT device mapping with Sub-NUMA clustering
Kconfig:
- Remove unnecessary "if X86"
MAINTAINERS:
- repair file entry in MICROSOFT SURFACE AGGREGATOR TABLET-MODE SWITCH
Merge tag 'ib-mfd-edac-i2c-leds-pinctrl-platform-watchdog-v5.20' into review-hans:
- Merge tag 'ib-mfd-edac-i2c-leds-pinctrl-platform-watchdog-v5.20' into review-hans
Move AMD platform drivers to separate directory:
- Move AMD platform drivers to separate directory
acer-wmi:
- Use backlight helper
acer_wmi:
- Cleanup Kconfig selects
apple-gmux:
- Use backlight helper
asus-wmi:
- Add mic-mute LED classdev support
- Add key mappings
compal-laptop:
- Use backlight helper
efi:
- Fix efi_power_off() not being run before acpi_power_off() when necessary
gigabyte-wmi:
- add support for B660I AORUS PRO DDR4
hp-wmi:
- Ignore Sanitization Mode event
i2c:
- i801: convert to use common P2SB accessor
ideapad-laptop:
- Add Ideapad 5 15ITL05 to ideapad_dytc_v4_allow_table[]
- Add allow_v4_dytc module parameter
intel/pmc:
- Add Alder Lake N support to PMC core driver
intel_atomisp2_led:
- Also turn off the always-on camera LED on the Asus T100TAF
leds:
- simatic-ipc-leds-gpio: Add GPIO version of Siemens driver
- simatic-ipc-leds: Convert to use P2SB accessor
mfd:
- lpc_ich: Add support for pinctrl in non-ACPI system
- lpc_ich: Switch to generic p2sb_bar()
- lpc_ich: Factor out lpc_ich_enable_spi_write()
mlx-platform:
- Add COME board revision register
- Add support for new system XH3000
- Introduce support for COMe NVSwitch management module for Vulcan chassis
- Add support for systems equipped with two ASICs
- Add cosmetic changes for alignment
- Make activation of some drivers conditional
p2sb:
- Move out of X86_PLATFORM_DEVICES dependency
panasonic-laptop:
- Use acpi_video_get_backlight_type()
- filter out duplicate volume up/down/mute keypresses
- don't report duplicate brightness key-presses
- revert "Resolve hotkey double trigger bug"
- sort includes alphabetically
- de-obfuscate button codes
pinctrl:
- intel: Check against matching data instead of ACPI companion
platform/mellanox:
- mlxreg-lc: Fix error flow and extend verbosity
- mlxreg-io: Add locking for io operations
- nvsw-sn2201: fix error code in nvsw_sn2201_create_static_devices()
platform/olpc:
- Fix uninitialized data in debugfs write
platform/surface:
- gpe: Add support for 13" Intel version of Surface Laptop 4
- tabletsw: Fix __le32 integer access
- Update copyright year of various drivers
- aggregator: Move subsystem hub drivers to their own module
- aggregator: Move device registry helper functions to core module
- aggregator_registry: Add support for tablet mode switch on Surface Laptop Studio
- aggregator_registry: Add support for tablet mode switch on Surface Pro 8
- Add KIP/POS tablet-mode switch driver
- aggregator: Add helper macros for requests with argument and return value
- aggregator: Reserve more event- and target-categories
- avoid flush_scheduled_work() usage
- aggregator_registry: Add support for keyboard cover on Surface Pro 8
- aggregator_registry: Add KIP device hub
- aggregator_registry: Change device ID for base hub
- aggregator_registry: Generify subsystem hub functionality
- aggregator: Add comment for KIP subsystem category
- aggregator_registry: Use client device wrappers for notifier registration
- aggregator: Allow notifiers to avoid communication on unregistering
- aggregator: Allow devices to be marked as hot-removed
- aggregator: Allow is_ssam_device() to be used when CONFIG_SURFACE_AGGREGATOR_BUS is disabled
platform/x86/amd/pmc:
- Add new platform support
- Add new acpi id for PMC controller
platform/x86/dell:
- Kconfig: Remove unnecessary "depends on X86_PLATFORM_DEVICES"
platform/x86/intel:
- Add Primary to Sideband (P2SB) bridge support
platform/x86/intel/ifs:
- Mark as BROKEN
platform/x86/intel/pmt:
- telemetry: Fix fixed region handling
platform/x86/intel/vsec:
- Fix wrong type for local status variables
- Add PCI error recovery support to Intel PMT
- Add support for Raptor Lake
- Rework early hardware code
pmc_atom:
- Fix comment typo
- Match all Lex BayTrail boards with critclk_systems DMI table
power/supply:
- surface_battery: Use client device wrappers for notifier registration
- surface_charger: Use client device wrappers for notifier registration
serial-multi-instantiate:
- Sort ACPI IDs by HID
- Get rid of redundant 'else'
- Use while (i--) pattern to clean up
- Improve dev_err_probe() messaging
- Drop duplicate check
- Improve autodetection
simatic-ipc:
- drop custom P2SB bar code
sony-laptop:
- Remove useless comparisons in sony_pic_read_possible_resource()
system76_acpi:
- Use dev_get_drvdata
thinkpad_acpi:
- Enable AMT by default on supported systems
- Add support for hotkey 0x131a
- Add support for automatic mode transitions
- profile capabilities as integer
- do not use PSC mode on Intel platforms
- Fix a memory leak of EFCH MMIO resource
- Replace custom str_on_off() etc
- Sort headers for better maintenance
- Use backlight helper
tools/power/x86/intel-speed-select:
- Remove unneeded semicolon
- Fix off by one check
watchdog:
- simatic-ipc-wdt: convert to use P2SB accessor
x86-android-tablets:
- Fix Lenovo Yoga Tablet 2 830/1050 poweroff again
-----BEGIN PGP SIGNATURE-----
iQFIBAABCAAyFiEEuvA7XScYQRpenhd+kuxHeUQDJ9wFAmLrndEUHGhkZWdvZWRl
QHJlZGhhdC5jb20ACgkQkuxHeUQDJ9zeMgf7BjSCz6ZA8SSY1i8QHDTvdjySihHJ
j07Gn3j1T/5G00R/r6viMDE4PxcYvMAPXjq3azepKQd8H5kGfE323SA6fgWFPAvi
P2OvEfvWfI5S8FYGYPBkNP2MjQ5MFe7qzLEh3+wQH0ocJ7WRCi457B4Xvtd2gWI3
dHj5gMSWC3O5xNa2S4Mg3dnD9uJlwhX+FNjWIuRy8eh5+DikgByyC4B+uW6WtO5e
t0rmIm6q5wUzB7dIetJLoAQwrcpYAOkK7L33G9h/7knWAfiJfklaKTbftnoxbDSv
iGWODkLDyob4C48DmVusS6WMEhPUzl/R33+tk6LjVt/YOYOP030EMtCECQ==
=Krhc
-----END PGP SIGNATURE-----
Merge tag 'platform-drivers-x86-v6.0-1' of git://git.kernel.org/pub/scm/linux/kernel/git/pdx86/platform-drivers-x86
Pull x86 platform driver updates from Hans de Goede:
- Microsoft Surface:
- SSAM hot unplug support
- Surface Pro 8 keyboard cover support
- Tablet mode switch support for Surface Pro 8 and Surface Laptop
Studio
- thinkpad_acpi:
- AMD Automatice Mode Transitions (AMT) support
- Mellanox:
- Vulcan chassis COMe NVSwitch management support
- XH3000 support
- New generic/shared Intel P2SB (Primary to Sideband) support
- Lots of small cleanups
- Various small bugfixes
- Various new hardware ids / quirks additions
* tag 'platform-drivers-x86-v6.0-1' of git://git.kernel.org/pub/scm/linux/kernel/git/pdx86/platform-drivers-x86: (105 commits)
platform/x86/intel/vsec: Fix wrong type for local status variables
platform/x86: p2sb: Move out of X86_PLATFORM_DEVICES dependency
platform/x86: pmc_atom: Fix comment typo
platform/surface: gpe: Add support for 13" Intel version of Surface Laptop 4
platform/olpc: Fix uninitialized data in debugfs write
platform/mellanox: mlxreg-lc: Fix error flow and extend verbosity
platform/x86: pmc_atom: Match all Lex BayTrail boards with critclk_systems DMI table
platform/x86: sony-laptop: Remove useless comparisons in sony_pic_read_possible_resource()
tools/power/x86/intel-speed-select: Remove unneeded semicolon
tools/power/x86/intel-speed-select: Fix off by one check
platform/surface: tabletsw: Fix __le32 integer access
Documentation/ABI: Add new attributes for mlxreg-io sysfs interfaces
Documentation/ABI: mlxreg-io: Fix contact info
platform/mellanox: mlxreg-io: Add locking for io operations
platform/x86: mlx-platform: Add COME board revision register
platform/x86: mlx-platform: Add support for new system XH3000
platform/x86: mlx-platform: Introduce support for COMe NVSwitch management module for Vulcan chassis
platform/x86: mlx-platform: Add support for systems equipped with two ASICs
platform/x86: mlx-platform: Add cosmetic changes for alignment
platform/x86: mlx-platform: Make activation of some drivers conditional
...
Here is the set of SPDX comment updates for 6.0-rc1.
Nothing huge here, just a number of updated SPDX license tags and
cleanups based on the review of a number of common patterns in GPLv2
boilerplate text. Also included in here are a few other minor updates,
2 USB files, and one Documentation file update to get the SPDX lines
correct.
All of these have been in the linux-next tree for a very long time.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCYupz3g8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ynPUgCgslaf2ssCgW5IeuXbhla+ZBRAzisAnjVgOvLN
4AKdqbiBNlFbCroQwmeQ
=v1sg
-----END PGP SIGNATURE-----
Merge tag 'spdx-6.0-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/spdx
Pull SPDX updates from Greg KH:
"Here is the set of SPDX comment updates for 6.0-rc1.
Nothing huge here, just a number of updated SPDX license tags and
cleanups based on the review of a number of common patterns in GPLv2
boilerplate text.
Also included in here are a few other minor updates, two USB files,
and one Documentation file update to get the SPDX lines correct.
All of these have been in the linux-next tree for a very long time"
* tag 'spdx-6.0-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/spdx: (28 commits)
Documentation: samsung-s3c24xx: Add blank line after SPDX directive
x86/crypto: Remove stray comment terminator
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_406.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_398.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_391.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_390.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_385.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_320.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_319.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_318.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_298.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_292.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_179.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_168.RULE (part 2)
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_168.RULE (part 1)
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_160.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_152.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_149.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_147.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_133.RULE
...
In olpc_battery_probe(), we should hold the reference returned by
of_find_compatible_node() and use it to call of_node_put() for
refcount balance.
Signed-off-by: Liang He <windhl@126.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
It seems to me that ab8500 driver is using dedicated workqueues and
is not calling schedule{,_delayed}_work{,_on}(). Then, there will be
no work to flush using flush_scheduled_work().
Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Some leftover code for external chargers only used with
unreleased ASIC revisions and the header file for the
unsupported PM2301 was left behind in an earlier cleanup,
fix it by deleting the remnants.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
It seems to be a typo, there is no actual BUG, but it's better to
fix it to avoid any possible BUG after we change the type of
supplied_from.
Signed-off-by: Schspa Shi <schspa@gmail.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
sparse reports
drivers/power/reset/pwr-mlxbf.c:19:12: warning: symbol 'rst_pwr_hid' was not declared. Should it be static?
drivers/power/reset/pwr-mlxbf.c:20:12: warning: symbol 'low_pwr_hid' was not declared. Should it be static?
Both rst_pwr_hid and low_pwr_hid are only used in a single function
so they should be local variables.
Fixes: a4c0094fcf ("power: reset: pwr-mlxbf: add BlueField SoC power control driver")
Signed-off-by: Tom Rix <trix@redhat.com>
Acked-by: Asmaa Mnebhi <asmaa@nvidia.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Add missing include for devm_work_autocancel to fix build error:
drivers/power/reset/pwr-mlxbf.c: In function 'pwr_mlxbf_probe':
drivers/power/reset/pwr-mlxbf.c:67:15: error: implicit declaration of function 'devm_work_autocancel' [-Werror=implicit-function-declaration]
67 | err = devm_work_autocancel(dev, &priv->send_work, pwr_mlxbf_send_work);
| ^~~~~~~~~~~~~~~~~~~~
cc1: all warnings being treated as errors
Fixes: a4c0094fcf ("power: reset: pwr-mlxbf: add BlueField SoC power control driver")
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Asmaa Mnebhi <asmaa@nvidia.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
This adds reset controller support for SAMA7G5 SoCs. Compared with
previous version the reset controller embedded on SAMA7G5 is able to
reset individual on SoC devices (e.g. USB PHY controllers).
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
-----BEGIN PGP SIGNATURE-----
iQIzBAABCgAdFiEE72YNB0Y/i3JqeVQT2O7X88g7+poFAmKsnYYACgkQ2O7X88g7
+pqRDRAApx77QWoH7xQ709cc4F77Y9dO6vtAhANtwloS1SAE4//bu2rds0bunWVG
096BQMXMo1U0NFUiNlPkCYHVBKPkYJPPXAUuL83nIF1Q+Y+mxpVbqaitQOgUvus4
nrToZvMQdStjSU7XbkXyQ3gtNKqHR5m2pSWmkbd/v7UZY057Djj6g65r5zqc3Weq
fdcw6ID9vRTvlt8KOw7G+BKjNTPOY0zSWnIyJTJjRMQUSqAXb5kYS7vkup1q0Z10
GOw1ZdNnhkZvvSguQFDobq6cLq0IEs/pHt+DXoaUCBogJQ/DH8zv4HVoTVyzLbXC
Lp9ALk+ApGWHIMIcaDmxuOTdAAiFqsSlYaBotuKC/0Iek6lSXltPvLW3lsgtvZp5
lgbv6SXo7iafKcHybF8607Waw55vHx+TOr9YziAlTwtEf1+dn04/31rkqYzjXp7N
CVXzNrIGVW9iRewbwQams758FcXoj5LPd1hG1Dt3GpAv1YHGc8PIkqBYZ2VYrCZ2
D6cas7NJOWpJnkVd4Yezx3jHFMOK9o/AYQDYgcnmBV0tS8M7rkrAPVkqXX+WdpSg
hMDq7hqB2crbyVvPbpYEeIKiy7/jr+eALfcO1gpHUhZpu6szf3cK+kN4hNsQw6bh
bVJtcuFRe19/kq7SKkMf77RJxEK9mYT7Vq47e6untftaXuzjn6w=
=yEq+
-----END PGP SIGNATURE-----
Merge tag 'at91-reset-sama7g5-signed' into psy-next
This adds reset controller support for SAMA7G5 SoCs. Compared with
previous version the reset controller embedded on SAMA7G5 is able to
reset individual on SoC devices (e.g. USB PHY controllers).
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Add support for SAMA7G5 including reset_controller_dev support for 3 lines
(which are USB PHYs).
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
SAMA7G5 reset controller has 5 extra lines that goes to different devices
(3 lines to USB PHYs, 1 line to DDR controller, 1 line to DDR PHY
controller). These reset lines could be requested by different controller
drivers (e.g. USB PHY driver) and these controllers' drivers could
assert/deassert these lines when necessary. Thus add support for
reset_controller_dev which brings this functionality.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Add struct at91_reset_data to keep per platform related information.
This is a prerequisite for adding reset_controller_dev support.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
This driver supports handling 2 BlueField power states controlled by
GPIO interrupts:
1) chip reset and
2) low power mode
Signed-off-by: Asmaa Mnebhi <asmaa@nvidia.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Use newly introduced client device wrapper functions for notifier
registration and unregistration.
Signed-off-by: Maximilian Luz <luzmaximilian@gmail.com>
Acked-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Link: https://lore.kernel.org/r/20220527023447.2460025-7-luzmaximilian@gmail.com
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Use newly introduced client device wrapper functions for notifier
registration and unregistration.
Signed-off-by: Maximilian Luz <luzmaximilian@gmail.com>
Acked-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Link: https://lore.kernel.org/r/20220527023447.2460025-6-luzmaximilian@gmail.com
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Based on the normalized pattern:
this program is free software you can redistribute it and/or modify it
under the terms of the gnu general public license version 2 as
published by the free software foundation this program is distributed
as is without any warranty of any kind whether express or implied
without even the implied warranty of merchantability or fitness for a
particular purpose see the gnu general public license for more details
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference.
Reviewed-by: Allison Randal <allison@lohutok.net>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on the normalized pattern:
this program is free software you can redistribute it and/or modify it
under the terms of the gnu general public license as published by the
free software foundation version 2 this program is distributed as is
without any warranty of any kind whether express or implied without
even the implied warranty of merchantability or fitness for a
particular purpose see the gnu general public license for more details
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference.
Reviewed-by: Allison Randal <allison@lohutok.net>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The maintenance charging is supposedly designed such that the
maintenance current compensates for the battery discharge curve,
and as the charging progress from CC/CV -> maintenance A ->
maintenance B states, we end up on a reasonable voltage to
restart ordinary CC/CV charging after the safety timer at the
maintenance B state exits.
However: old batteries discharge quicker, and in an old
battery we might not get to the expiration of the maintenance B
timer before the battery is completely depleted and the system
powers off with an empty battery.
This is hardly the desire of anyone leaving their phone in the
charger for a few days!
Introduce a second clause in both maintenance states such that
we exit the state and return to ordinary CC/CV charging if
the voltage drops below charge_restart_voltage_uv or 95%
if this is not defined for the battery.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Matti Vaittinen <mazziesaccount@gmail.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
The battery info contains a voltage indicating when the voltage
is so low that it is time to restart the CC/CV charging.
Make the AB8500 respect and prioritize this setting over the
hardcoded 95% threshold.
Break out the check into its own function and add some safeguards
so we do not run into unpredictable side effects.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Matti Vaittinen <mazziesaccount@gmail.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Similar to the handling of cros_usbpd_charger_ec_command in commit 441d38c60f
("power: supply: cros_usbpd: Use struct_size() helper in kzalloc()"),
we thought a patch might be needed here as well.
Make use of the struct_size() helper instead of an open-coded version,
in order to avoid any potential type mistakes or integer overflows that,
in the worst scenario, could lead to heap overflows.
Signed-off-by: Xiaohui Zhang <xiaohuizhang@ruc.edu.cn>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
The functions power_supply_temp2resist_simple and power_supply_ocv2cap_simple
handle boundary conditions incorrectly.
The change was introduced in a4585ba205
("power: supply: core: Use library interpolation").
There are two issues: First, the lines "high = i - 1" and "high = i" in ocv2cap
have the wrong order compared to temp2resist. As a consequence, ocv2cap
sets high=-1 if ocv>table[0].ocv, which causes an out-of-bounds read.
Second, the logic of temp2resist is also not correct.
Consider the case table[] = {{20, 100}, {10, 80}, {0, 60}}.
For temp=5, we expect a resistance of 70% by interpolation.
However, temp2resist sets high=low=2 and returns 60.
Cc: stable@vger.kernel.org
Signed-off-by: Dorian Rudolph <mail@dorianrudolph.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Fixes: a4585ba205 ("power: supply: core: Use library interpolation")
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
of_find_matching_node_and_match() returns a node pointer with refcount
incremented, we should use of_node_put() on it when not need anymore.
Add missing of_node_put() to avoid refcount leak.
Fixes: 0e545f57b7 ("power: reset: driver for the Versatile syscon reboot")
Signed-off-by: Miaoqian Lin <linmq006@gmail.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
The print function dev_err() is redundant because
platform_get_irq() already prints an error.
Eliminate the follow coccicheck warning:
./drivers/power/supply/goldfish_battery.c:225:2-9: line 225 is
redundant because platform_get_irq() already prints an error
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Signed-off-by: Yang Li <yang.lee@linux.alibaba.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Spelling mistake (triple letters) in comment.
Detected with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@inria.fr>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
My Bootlin address is preferred from now on.
Signed-off-by: Luca Ceresoli <luca@lucaceresoli.net>
Signed-off-by: Luca Ceresoli <luca.ceresoli@bootlin.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Here is the large set of char, misc, and other driver subsystem updates
for 5.19-rc1. The merge request for this has been delayed as I wanted
to get lots of linux-next testing due to some late arrivals of changes
for the habannalabs driver.
Highlights of this merge are:
- habanalabs driver updates for new hardware types and fixes and
other updates
- IIO driver tree merge which includes loads of new IIO drivers
and cleanups and additions
- PHY driver tree merge with new drivers and small updates to
existing ones
- interconnect driver tree merge with fixes and updates
- soundwire driver tree merge with some small fixes
- coresight driver tree merge with small fixes and updates
- mhi bus driver tree merge with lots of updates and new device
support
- firmware driver updates
- fpga driver updates
- lkdtm driver updates (with a merge conflict, more on that
below)
- extcon driver tree merge with small updates
- lots of other tiny driver updates and fixes and cleanups, full
details in the shortlog.
All of these have been in linux-next for almost 2 weeks with no reported
problems.
Note, there are 3 merge conflicts when merging this with your tree:
- MAINTAINERS, should be easy to resolve
- drivers/slimbus/qcom-ctrl.c, should be straightforward
resolution
- drivers/misc/lkdtm/stackleak.c, not an easy resolution. This
has been noted in the linux-next tree for a while, and
resolved there, here's a link to the resolution that Stephen
came up with and that Kees says is correct:
https://lore.kernel.org/r/20220509185344.3fe1a354@canb.auug.org.au
I will be glad to provide a merge point that contains these resolutions
if that makes things any easier for you.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCYpnkbA8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ylOrgCggbbAFwESBY9o2YfpG+2VOLpc0GAAoJgY1XN8
P/gumbLEpFvoBZ5xLIW8
=KCgk
-----END PGP SIGNATURE-----
Merge tag 'char-misc-5.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char / misc / other smaller driver subsystem updates from Greg KH:
"Here is the large set of char, misc, and other driver subsystem
updates for 5.19-rc1. The merge request for this has been delayed as I
wanted to get lots of linux-next testing due to some late arrivals of
changes for the habannalabs driver.
Highlights of this merge are:
- habanalabs driver updates for new hardware types and fixes and
other updates
- IIO driver tree merge which includes loads of new IIO drivers and
cleanups and additions
- PHY driver tree merge with new drivers and small updates to
existing ones
- interconnect driver tree merge with fixes and updates
- soundwire driver tree merge with some small fixes
- coresight driver tree merge with small fixes and updates
- mhi bus driver tree merge with lots of updates and new device
support
- firmware driver updates
- fpga driver updates
- lkdtm driver updates (with a merge conflict, more on that below)
- extcon driver tree merge with small updates
- lots of other tiny driver updates and fixes and cleanups, full
details in the shortlog.
All of these have been in linux-next for almost 2 weeks with no
reported problems"
* tag 'char-misc-5.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (387 commits)
habanalabs: use separate structure info for each error collect data
habanalabs: fix missing handle shift during mmap
habanalabs: remove hdev from hl_ctx_get args
habanalabs: do MMU prefetch as deferred work
habanalabs: order memory manager messages
habanalabs: return -EFAULT on copy_to_user error
habanalabs: use NULL for eventfd
habanalabs: update firmware header
habanalabs: add support for notification via eventfd
habanalabs: add topic to memory manager buffer
habanalabs: handle race in driver fini
habanalabs: add device memory scrub ability through debugfs
habanalabs: use unified memory manager for CB flow
habanalabs: unified memory manager new code for CB flow
habanalabs/gaudi: set arbitration timeout to a high value
habanalabs: add put by handle method to memory manager
habanalabs: hide memory manager page shift
habanalabs: Add separate poll interval value for protocol
habanalabs: use get_task_pid() to take PID
habanalabs: add prefetch flag to the MAP operation
...
The second part of the multiplatform changes now converts the
Intel/Marvell PXA platform along with the rest. The patches went through
several rebases before the merge window as bugs were found, so they
remained separate.
This has to touch a lot of drivers, in particular the touchscreen,
pcmcia, sound and clk bits, to detach the driver files from the
platform and board specific header files.
-----BEGIN PGP SIGNATURE-----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=cnSb
-----END PGP SIGNATURE-----
Merge tag 'arm-multiplatform-5.19-2' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull more ARM multiplatform updates from Arnd Bergmann:
"The second part of the multiplatform changes now converts the
Intel/Marvell PXA platform along with the rest. The patches went
through several rebases before the merge window as bugs were found, so
they remained separate.
This has to touch a lot of drivers, in particular the touchscreen,
pcmcia, sound and clk bits, to detach the driver files from the
platform and board specific header files"
* tag 'arm-multiplatform-5.19-2' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (48 commits)
ARM: pxa/mmp: remove traces of plat-pxa
ARM: pxa: convert to multiplatform
ARM: pxa/sa1100: move I/O space to PCI_IOBASE
ARM: pxa: remove support for MTD_XIP
ARM: pxa: move mach/*.h to mach-pxa/
ARM: PXA: fix multi-cpu build of xsc3
ARM: pxa: move plat-pxa to drivers/soc/
ARM: mmp: rename pxa_register_device
ARM: mmp: remove tavorevb board support
ARM: pxa: remove unused mach/bitfield.h
ARM: pxa: move clk register definitions to driver
ARM: pxa: move smemc register access from clk to platform
cpufreq: pxa3: move clk register access to clk driver
ARM: pxa: remove get_clk_frequency_khz()
ARM: pxa: pcmcia: move smemc configuration back to arch
ASoC: pxa: i2s: use normal MMIO accessors
ASoC: pxa: ac97: use normal MMIO accessors
ASoC: pxa: use pdev resource for FIFO regs
Input: wm97xx - get rid of irq_enable method in wm97xx_mach_ops
Input: wm97xx - switch to using threaded IRQ
...
Merge power-supply fixes, that missed the v5.18 merge window
into power-supply's for-next branch.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
The extcon_get_extcon_dev() function returns error pointers on error,
NULL when it's a -EPROBE_DEFER defer situation, and ERR_PTR(-ENODEV)
when the CONFIG_EXTCON option is disabled. This is very complicated for
the callers to handle and a number of them had bugs that would lead to
an Oops.
In real life, there are two things which prevented crashes. First,
error pointers would only be returned if there was bug in the caller
where they passed a NULL "extcon_name" and none of them do that.
Second, only two out of the eight drivers will build when CONFIG_EXTCON
is disabled.
The normal way to write this would be to return -EPROBE_DEFER directly
when appropriate and return NULL when CONFIG_EXTCON is disabled. Then
the error handling is simple and just looks like:
dev->edev = extcon_get_extcon_dev(acpi_dev_name(adev));
if (IS_ERR(dev->edev))
return PTR_ERR(dev->edev);
For the two drivers which can build with CONFIG_EXTCON disabled, then
extcon_get_extcon_dev() will now return NULL which is not treated as an
error and the probe will continue successfully. Those two drivers are
"typec_fusb302" and "max8997-battery". In the original code, the
typec_fusb302 driver had an 800ms hang in tcpm_get_current_limit() but
now that function is a no-op. For the max8997-battery driver everything
should continue working as is.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
The Tosa device (Sharp SL-6000) has a mishmash driver set-up
for the Toshiba TC6393xb MFD that includes a battery charger
and touchscreen and has some kind of relationship to the SoC
sound driver for the AC97 codec. Other devices define a chip
like this but seem only half-implemented, not really handling
battery charging etc.
This patch switches the Toshiba MFD device to provide GPIO
descriptors to the battery charger and SoC codec. As a result
some descriptors need to be moved out of the Tosa boardfile
and new one added: all SoC GPIO resources to these drivers
now comes from the main boardfile, while the MFD provide
GPIOs for its portions.
As a result we can request one GPIO from our own GPIO chip
and drop two hairy callbacks into the board file.
This platform badly needs to have its drivers split up and
converted to device tree probing to handle this quite complex
relationship in an orderly manner. I just do my best in solving
the GPIO descriptor part of the puzzle. Please don't ask me
to fix everything that is wrong with these driver to todays
standards, I am just trying to fix one aspect. I do try to
use modern devres resource management and handle deferred
probe using new functions where appropriate.
Cc: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Cc: Dirk Opfer <dirk@opfer-online.de>
Cc: Robert Jarzmik <robert.jarzmik@free.fr>
Cc: Daniel Mack <daniel@zonque.org>
Cc: Haojian Zhuang <haojian.zhuang@gmail.com>
Cc: Lee Jones <lee.jones@linaro.org>
Cc: Liam Girdwood <lgirdwood@gmail.com>
Reviewed-by: Dmitry Baryshkov <dbaryshkov@gmail.com>
Acked-by: Mark Brown <broonie@kernel.org>
Acked-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Using pm_runtime_resume_and_get is more appropriate
for simplifing code
Reported-by: Zeal Robot <zealci@zte.com.cn>
Signed-off-by: Minghao Chi <chi.minghao@zte.com.cn>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
When the Capacity Inaccurate flag is set, the chip still provides data
about the battery, albeit inaccurate. Instead of discarding capacity
values for CI=1, expose the stale data and use the
POWER_SUPPLY_HEALTH_CALIBRATION_REQUIRED property to indicate that the
values should be used with care.
Reviewed-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Sicelo A. Mhlongo <absicsz@gmail.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
The workqueue is allocated in bind() but all interrupts are
registered in probe().
Some interrupts put work on the workqueue, which can have
bad side effects.
Allocate the workqueue in probe() instead, destroy it in
.remove() and make unbind() simply flush the workqueue.
Fixes: 1c1f13a006 ("power: supply: ab8500: Move to componentized binding")
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Some "T3 MRD" mini-PCs / HDMI-sticks without a battery use a different
value then "5.11" for their DMI BIOS version field.
Drop the BIOS version check so that the no-battery "T3 MRD" DMI quirk
applies to these too.
Fixes: 3a06b912a5 ("power: supply: axp288_fuel_gauge: Make "T3 MRD" no_battery_list DMI entry more generic")
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Commit 3a06b912a5 ("power: supply: axp288_fuel_gauge: Make "T3 MRD"
no_battery_list DMI entry more generic") added a generic no-battery DMI
match for many mini-PCs / HDMI-sticks which use "T3 MRD" as their DMI
board-name.
It turns out that the One Mix 1 mini laptop also uses "T3 MRD" for its
DMI boardname and it also has its chassis-type wrongly set to a value
of "3" (desktop). This was causing the axp288_fuel_gauge driver to
disable battery reporting because this matches the no-battery DMI
list entry for generic "T3 MRD" mini-PCs.
Change the no-battery DMI list into a quirks DMI list and add a
specific match for the One Mix 1 mini laptop before the generic
"T3 MRD" no-battery quirk entry to fix this.
Fixes: 3a06b912a5 ("power: supply: axp288_fuel_gauge: Make "T3 MRD" no_battery_list DMI entry more generic")
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
As we rely on pointers in the battery info to be zero-initialized
such as in the helper function power_supply_supports_vbat2ri()
we certainly need to allocate the struct power_supply_battery_info
with kzalloc() as well. Else this happens:
Unable to handle kernel paging request at virtual address 00280000
(...)
PC is at power_supply_vbat2ri+0x50/0x12c
LR is at ab8500_fg_battery_resistance+0x34/0x108
Fixes: e9e7d165b4 ("power: supply: Support VBAT-to-Ri lookup tables")
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Otherwise power_supply_get_battery_info always returns -ENODEV
on devices that do not have a static battery, even when a simple
battery is found.
Fixes: c8aee3f41c ("power: supply: Static data for Samsung batteries")
Signed-off-by: Yassine Oudjana <y.oudjana@protonmail.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Two of the batteries were missing charging restart voltages,
meaning they can drain if the algorithm relies on restarting
charging at this voltage. Fix it up.
Fixes: c8aee3f41c ("power: supply: Static data for Samsung batteries")
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Here is the set of driver core changes for 5.18-rc1.
Not much here, primarily it was a bunch of cleanups and small updates:
- kobj_type cleanups for default_groups
- documentation updates
- firmware loader minor changes
- component common helper added and take advantage of it in many
drivers (the largest part of this pull request).
There will be a merge conflict in drivers/power/supply/ab8500_chargalg.c
with your tree, the merge conflict should be easy (take all the
changes).
All of these have been in linux-next for a while with no reported
problems.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCYkG6PA8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ylMFwCfSIyAU4oLEgj+/Rfmx4o45cAVIWMAnit3zbdU
wUUCGqKcOnTJEcW6dMPh
=1VVi
-----END PGP SIGNATURE-----
Merge tag 'driver-core-5.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core updates from Greg KH:
"Here is the set of driver core changes for 5.18-rc1.
Not much here, primarily it was a bunch of cleanups and small updates:
- kobj_type cleanups for default_groups
- documentation updates
- firmware loader minor changes
- component common helper added and take advantage of it in many
drivers (the largest part of this pull request).
All of these have been in linux-next for a while with no reported
problems"
* tag 'driver-core-5.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (54 commits)
Documentation: update stable review cycle documentation
drivers/base/dd.c : Remove the initial value of the global variable
Documentation: update stable tree link
Documentation: add link to stable release candidate tree
devres: fix typos in comments
Documentation: add note block surrounding security patch note
samples/kobject: Use sysfs_emit instead of sprintf
base: soc: Make soc_device_match() simpler and easier to read
driver core: dd: fix return value of __setup handler
driver core: Refactor sysfs and drv/bus remove hooks
driver core: Refactor multiple copies of device cleanup
scripts: get_abi.pl: Fix typo in help message
kernfs: fix typos in comments
kernfs: remove unneeded #if 0 guard
ALSA: hda/realtek: Make use of the helper component_compare_dev_name
video: omapfb: dss: Make use of the helper component_compare_dev
power: supply: ab8500: Make use of the helper component_compare_dev
ASoC: codecs: wcd938x: Make use of the helper component_compare/release_of
iommu/mediatek: Make use of the helper component_compare/release_of
drm: of: Make use of the helper component_release_of
...
power-supply core:
- Introduce "Bypass" charging type used by USB PPS standard
- Refactor power_supply_set_input_current_limit_from_supplier()
- Add fwnode support to power_supply_get_battery_info()
Drivers:
- ab8500: continue migrating towards using standard core APIs
- axp288 fuel-gauge: refactor driver to be fully resource managed
- battery-samsung-sdi: new in-kernel provider for (constant) Samsung battery info
- bq24190: disable boost regulator on shutdown
- bq24190: add support for battery-info on ACPI based systems
- bq25890: prepare driver for usage on ACPI based systems
- bq25890: add boost regulator support
- cpcap-battery: add NVMEM based battery detection support
- injoinic ip5xxx: new driver for power bank IC
- upi ug3105: new battery driver
- misc. small improvements and fixes
-----BEGIN PGP SIGNATURE-----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=OiYc
-----END PGP SIGNATURE-----
Merge tag 'for-v5.18' of git://git.kernel.org/pub/scm/linux/kernel/git/sre/linux-power-supply
Pull power supply and reset updates from Sebastian Reichel:
"Power-supply core:
- Introduce "Bypass" charging type used by USB PPS standard
- Refactor power_supply_set_input_current_limit_from_supplier()
- Add fwnode support to power_supply_get_battery_info()
Drivers:
- ab8500: continue migrating towards using standard core APIs
- axp288 fuel-gauge: refactor driver to be fully resource managed
- battery-samsung-sdi: new in-kernel provider for (constant) Samsung
battery info
- bq24190: disable boost regulator on shutdown
- bq24190: add support for battery-info on ACPI based systems
- bq25890: prepare driver for usage on ACPI based systems
- bq25890: add boost regulator support
- cpcap-battery: add NVMEM based battery detection support
- injoinic ip5xxx: new driver for power bank IC
- upi ug3105: new battery driver
- misc small improvements and fixes"
* tag 'for-v5.18' of git://git.kernel.org/pub/scm/linux/kernel/git/sre/linux-power-supply: (94 commits)
power: ab8500_chargalg: Use CLOCK_MONOTONIC
power: supply: Add a driver for Injoinic power bank ICs
dt-bindings: trivial-devices: Add Injoinic power bank ICs
dt-bindings: vendor-prefixes: Add Injoinic
power: supply: ab8500: Remove unused variable
power: supply: da9150-fg: Remove unnecessary print function dev_err()
power: supply: ab8500: fix a handful of spelling mistakes
power: supply: ab8500_fg: Account for line impedance
dt-bindings: power: supply: ab8500_fg: Add line impedance
power: supply: axp20x_usb_power: fix platform_get_irq.cocci warnings
power: supply: axp20x_ac_power: fix platform_get_irq.cocci warning
power: supply: wm8350-power: Add missing free in free_charger_irq
power: supply: wm8350-power: Handle error for wm8350_register_irq
power: supply: Static data for Samsung batteries
power: supply: ab8500_fg: Use VBAT-to-Ri if possible
power: supply: Support VBAT-to-Ri lookup tables
power: supply: ab8500: Standardize BTI resistance
power: supply: ab8500: Standardize alert mode charging
power: supply: ab8500: Standardize maintenance charging
power: supply: bq24190_charger: Delay applying charge_type changes when OTG 5V Vbus boost is on
...
The HRTimer in the AB8500 charging code is using CLOCK_REALTIME
to set an alarm some hours forward in time +/- 5 min for a safety
timer.
I have observed that this will sometimes fire sporadically
early when charging a battery with the result that
charging stops.
As CLOCK_REALTIME can be subject to adjustments of time from
sources such as NTP, this cannot be trusted and will likely
for example fire events if the clock is set forward some hours
by say NTP.
Use CLOCK_MONOTONIC as indicated in other instances and the
problem goes away. Also initialize the timer to REL mode
as this is what will be used later.
Fixes: 257107ae6b ("ab8500-chargalg: Use hrtimer")
Cc: Lee Jones <lee.jones@linaro.org>
Suggested-by: Matti Vaittinen <mazziesaccount@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
This driver supports several chip variants which all share the same I2C
register interface. Since the chip will turn off and become inaccessible
under conditions outside of software control (e.g. upon button press or
input voltage removal), some special handling is needed to delay the
initialization of the IC until it is accessible.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Kernel test robot reported below warning ->
drivers/power/supply/ab8500_chargalg.c:790:13: warning:
variable 'delta_i_ua' set but not used [-Wunused-but-set-variable]
Remove unused variable delta_i_ua.
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Souptick Joarder (HPE) <jrdr.linux@gmail.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
The print function dev_err() is redundant because
platform_get_irq_byname() already prints an error.
Eliminate the follow coccicheck warning:
./drivers/power/supply/da9150-fg.c:524:2-9: line 524 is redundant
because platform_get_irq() already prints an error
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Signed-off-by: Yang Li <yang.lee@linux.alibaba.com>
Reviewed-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Linus Torvalds
Liang He
Zheng Bin
Tetsuo Handa
Jiang Jian
Linus Walleij
Schspa Shi
Tom Rix
Asmaa Mnebhi
Sebastian Reichel
Claudiu Beznea
Maximilian Luz
Thomas Gleixner
Xiaohui Zhang
Xiang wangx
Dorian Rudolph
Miaoqian Lin
Gao Chao
Yang Li
Julia Lawall
Luca Ceresoli
Dan Carpenter
Minghao Chi
Sicelo A. Mhlongo
Hans de Goede
Yassine Oudjana
Samuel Holland
Souptick Joarder (HPE)