Here is the big set of tty and serial driver changes for 6.0-rc1.
It was delayed from last week as I wanted to make sure the last commit
here got some good testing in linux-next and elsewhere as it seemed to
show up only late in testing for some reason.
Nothing major here, just lots of cleanups from Jiri and Ilpo to make the
tty core cleaner (Jiri) and the rs485 code simpler to use (Ilpo). Also
included in here is the obligatory n_gsm updates from Daniel Starke and
lots of tiny driver updates and minor fixes and tweaks for other smaller
serial drivers.
Full details are in the shortlog.
All of these have been in linux-next for a while with no reported
problems.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCYvD8qA8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ylfEQCdGiYLQkWUUarhnlocHo+kSm5vkvsAnicZg7Sl
IQBeAidA3dZEQO0lLlM5
=t7Yh
-----END PGP SIGNATURE-----
Merge tag 'tty-6.0-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty / serial driver updates from Greg KH:
"Here is the big set of tty and serial driver changes for 6.0-rc1.
It was delayed from last week as I wanted to make sure the last commit
here got some good testing in linux-next and elsewhere as it seemed to
show up only late in testing for some reason.
Nothing major here, just lots of cleanups from Jiri and Ilpo to make
the tty core cleaner (Jiri) and the rs485 code simpler to use (Ilpo).
Also included in here is the obligatory n_gsm updates from Daniel
Starke and lots of tiny driver updates and minor fixes and tweaks for
other smaller serial drivers.
All of these have been in linux-next for a while with no reported
problems"
* tag 'tty-6.0-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (186 commits)
tty: serial: qcom-geni-serial: Fix %lu -> %u in print statements
tty: amiserial: Fix comment typo
tty: serial: document uart_get_console()
tty: serial: serial_core, reformat kernel-doc for functions
Documentation: serial: link uart_ops properly
Documentation: serial: move GPIO kernel-doc to the functions
Documentation: serial: dedup kernel-doc for uart functions
Documentation: serial: move uart_ops documentation to the struct
dt-bindings: serial: snps-dw-apb-uart: Document Rockchip RV1126
serial: mvebu-uart: uart2 error bits clearing
tty: serial: fsl_lpuart: correct the count of break characters
serial: stm32: make info structs static to avoid sparse warnings
serial: fsl_lpuart: zero out parity bit in CS7 mode
tty: serial: qcom-geni-serial: Fix get_clk_div_rate() which otherwise could return a sub-optimal clock rate.
serial: 8250_bcm2835aux: Add missing clk_disable_unprepare()
tty: vt: initialize unicode screen buffer
serial: remove VR41XX serial driver
serial: 8250: lpc18xx: Remove redundant sanity check for RS485 flags
serial: 8250_dwlib: remove redundant sanity check for RS485 flags
dt_bindings: rs485: Correct delay values
...
- Add support for syscall stack randomization.
- Add support for atomic operations to the 32 & 64-bit BPF JIT.
- Full support for KASAN on 64-bit Book3E.
- Add a watchdog driver for the new PowerVM hypervisor watchdog.
- Add a number of new selftests for the Power10 PMU support.
- Add a driver for the PowerVM Platform KeyStore.
- Increase the NMI watchdog timeout during live partition migration, to avoid timeouts
due to increased memory access latency.
- Add support for using the 'linux,pci-domain' device tree property for PCI domain
assignment.
- Many other small features and fixes.
Thanks to: Alexey Kardashevskiy, Andy Shevchenko, Arnd Bergmann, Athira Rajeev, Bagas
Sanjaya, Christophe Leroy, Erhard Furtner, Fabiano Rosas, Greg Kroah-Hartman, Greg Kurz,
Haowen Bai, Hari Bathini, Jason A. Donenfeld, Jason Wang, Jiang Jian, Joel Stanley, Juerg
Haefliger, Kajol Jain, Kees Cook, Laurent Dufour, Madhavan Srinivasan, Masahiro Yamada,
Maxime Bizon, Miaoqian Lin, Murilo Opsfelder Araújo, Nathan Lynch, Naveen N. Rao, Nayna
Jain, Nicholas Piggin, Ning Qiang, Pali Rohár, Petr Mladek, Rashmica Gupta, Sachin Sant,
Scott Cheloha, Segher Boessenkool, Stephen Rothwell, Uwe Kleine-König, Wolfram Sang, Xiu
Jianfeng, Zhouyi Zhou.
-----BEGIN PGP SIGNATURE-----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=tRkm
-----END PGP SIGNATURE-----
Merge tag 'powerpc-6.0-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc updates from Michael Ellerman:
- Add support for syscall stack randomization
- Add support for atomic operations to the 32 & 64-bit BPF JIT
- Full support for KASAN on 64-bit Book3E
- Add a watchdog driver for the new PowerVM hypervisor watchdog
- Add a number of new selftests for the Power10 PMU support
- Add a driver for the PowerVM Platform KeyStore
- Increase the NMI watchdog timeout during live partition migration, to
avoid timeouts due to increased memory access latency
- Add support for using the 'linux,pci-domain' device tree property for
PCI domain assignment
- Many other small features and fixes
Thanks to Alexey Kardashevskiy, Andy Shevchenko, Arnd Bergmann, Athira
Rajeev, Bagas Sanjaya, Christophe Leroy, Erhard Furtner, Fabiano Rosas,
Greg Kroah-Hartman, Greg Kurz, Haowen Bai, Hari Bathini, Jason A.
Donenfeld, Jason Wang, Jiang Jian, Joel Stanley, Juerg Haefliger, Kajol
Jain, Kees Cook, Laurent Dufour, Madhavan Srinivasan, Masahiro Yamada,
Maxime Bizon, Miaoqian Lin, Murilo Opsfelder Araújo, Nathan Lynch,
Naveen N. Rao, Nayna Jain, Nicholas Piggin, Ning Qiang, Pali Rohár,
Petr Mladek, Rashmica Gupta, Sachin Sant, Scott Cheloha, Segher
Boessenkool, Stephen Rothwell, Uwe Kleine-König, Wolfram Sang, Xiu
Jianfeng, and Zhouyi Zhou.
* tag 'powerpc-6.0-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux: (191 commits)
powerpc/64e: Fix kexec build error
EDAC/ppc_4xx: Include required of_irq header directly
powerpc/pci: Fix PHB numbering when using opal-phbid
powerpc/64: Init jump labels before parse_early_param()
selftests/powerpc: Avoid GCC 12 uninitialised variable warning
powerpc/cell/axon_msi: Fix refcount leak in setup_msi_msg_address
powerpc/xive: Fix refcount leak in xive_get_max_prio
powerpc/spufs: Fix refcount leak in spufs_init_isolated_loader
powerpc/perf: Include caps feature for power10 DD1 version
powerpc: add support for syscall stack randomization
powerpc: Move system_call_exception() to syscall.c
powerpc/powernv: rename remaining rng powernv_ functions to pnv_
powerpc/powernv/kvm: Use darn for H_RANDOM on Power9
powerpc/powernv: Avoid crashing if rng is NULL
selftests/powerpc: Fix matrix multiply assist test
powerpc/signal: Update comment for clarity
powerpc: make facility_unavailable_exception 64s
powerpc/platforms/83xx/suspend: Remove write-only global variable
powerpc/platforms/83xx/suspend: Prevent unloading the driver
powerpc/platforms/83xx/suspend: Reorder to get rid of a forward declaration
...
There are three independent sets of changes:
- Sai Prakash Ranjan adds tracing support to the asm-generic
version of the MMIO accessors, which is intended to help
understand problems with device drivers and has been part
of Qualcomm's vendor kernels for many years.
- A patch from Sebastian Siewior to rework the handling of
IRQ stacks in softirqs across architectures, which is
needed for enabling PREEMPT_RT.
- The last patch to remove the CONFIG_VIRT_TO_BUS option and
some of the code behind that, after the last users of this
old interface made it in through the netdev, scsi, media and
staging trees.
-----BEGIN PGP SIGNATURE-----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=aTR0
-----END PGP SIGNATURE-----
Merge tag 'asm-generic-6.0' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/asm-generic
Pull asm-generic updates from Arnd Bergmann:
"There are three independent sets of changes:
- Sai Prakash Ranjan adds tracing support to the asm-generic version
of the MMIO accessors, which is intended to help understand
problems with device drivers and has been part of Qualcomm's vendor
kernels for many years
- A patch from Sebastian Siewior to rework the handling of IRQ stacks
in softirqs across architectures, which is needed for enabling
PREEMPT_RT
- The last patch to remove the CONFIG_VIRT_TO_BUS option and some of
the code behind that, after the last users of this old interface
made it in through the netdev, scsi, media and staging trees"
* tag 'asm-generic-6.0' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/asm-generic:
uapi: asm-generic: fcntl: Fix typo 'the the' in comment
arch/*/: remove CONFIG_VIRT_TO_BUS
soc: qcom: geni: Disable MMIO tracing for GENI SE
serial: qcom_geni_serial: Disable MMIO tracing for geni serial
asm-generic/io: Add logging support for MMIO accessors
KVM: arm64: Add a flag to disable MMIO trace for nVHE KVM
lib: Add register read/write tracing support
drm/meson: Fix overflow implicit truncation warnings
irqchip/tegra: Fix overflow implicit truncation warnings
coresight: etm4x: Use asm-generic IO memory barriers
arm64: io: Use asm-generic high level MMIO accessors
arch/*: Disable softirq stacks on PREEMPT_RT.
When we multiply an unsigned int by a u32 we still end up with an
unsigned int. That means we should specify "%u" not "%lu" in the
format code.
NOTE: this fix was chosen instead of somehow promoting the value to
"unsigned long" since the max baud rate from the earlier call to
uart_get_baud_rate() is 4000000 and the max sampling rate is 32.
4000000 * 32 = 0x07a12000, not even close to overflowing 32-bits.
Fixes: c474c77571 ("tty: serial: qcom-geni-serial: Fix get_clk_div_rate() which otherwise could return a sub-optimal clock rate.")
Reported-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20220802132250.1.Iea061e14157a17e114dbe2eca764568a02d6b889@changeid
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The SoC driver updates contain changes to improve support for
additional SoC variants, as well as cleanups an minor bugfixes
in a number of existing drivers.
Notable updates this time include:
- Support for Qualcomm MSM8909 (Snapdragon 210) in various drivers
- Updates for interconnect drivers on Qualcomm Snapdragon
- A new driver support for NMI interrupts on Fujitsu A64fx
- A rework of Broadcom BCMBCA Kconfig dependencies
- Improved support for BCM2711 (Raspberry Pi 4) power management
to allow the use of the V3D GPU
- Cleanups to the NXP guts driver
- Arm SCMI firmware driver updates to add tracing support, and
use the firmware interfaces for system power control and for
power capping.
-----BEGIN PGP SIGNATURE-----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=0dZI
-----END PGP SIGNATURE-----
Merge tag 'arm-drivers-6.0' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC drivers from Arnd Bergmann:
"The SoC driver updates contain changes to improve support for
additional SoC variants, as well as cleanups an minor bugfixes
in a number of existing drivers.
Notable updates this time include:
- Support for Qualcomm MSM8909 (Snapdragon 210) in various drivers
- Updates for interconnect drivers on Qualcomm Snapdragon
- A new driver support for NMI interrupts on Fujitsu A64fx
- A rework of Broadcom BCMBCA Kconfig dependencies
- Improved support for BCM2711 (Raspberry Pi 4) power management to
allow the use of the V3D GPU
- Cleanups to the NXP guts driver
- Arm SCMI firmware driver updates to add tracing support, and use
the firmware interfaces for system power control and for power
capping"
* tag 'arm-drivers-6.0' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (125 commits)
soc: a64fx-diag: disable modular build
dt-bindings: soc: qcom: qcom,smd-rpm: add power-controller
dt-bindings: soc: qcom: aoss: document qcom,sm8450-aoss-qmp
dt-bindings: soc: qcom,rpmh-rsc: simplify qcom,tcs-config
ARM: mach-qcom: Add support for MSM8909
dt-bindings: arm: cpus: Document "qcom,msm8909-smp" enable-method
soc: qcom: spm: Add CPU data for MSM8909
dt-bindings: soc: qcom: spm: Add MSM8909 CPU compatible
soc: qcom: rpmpd: Add compatible for MSM8909
dt-bindings: power: qcom-rpmpd: Add MSM8909 power domains
soc: qcom: smd-rpm: Add compatible for MSM8909
dt-bindings: soc: qcom: smd-rpm: Add MSM8909
soc: qcom: icc-bwmon: Remove unnecessary print function dev_err()
soc: fujitsu: Add A64FX diagnostic interrupt driver
soc: qcom: socinfo: Fix the id of SA8540P SoC
soc: qcom: Make QCOM_RPMPD depend on PM
tty: serial: bcm63xx: bcmbca: Replace ARCH_BCM_63XX with ARCH_BCMBCA
spi: bcm63xx-hsspi: bcmbca: Replace ARCH_BCM_63XX with ARCH_BCMBCA
clk: bcm: bcmbca: Replace ARCH_BCM_63XX with ARCH_BCMBCA
hwrng: bcm2835: bcmbca: Replace ARCH_BCM_63XX with ARCH_BCMBCA
...
This was the only function mentioned in the text, but was neither linked
nor documented. So document and link it, so that hyperlinking works in
the text.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20220728061056.20799-6-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There are many annotated functions in serial_core.c, but they do not
completely conform to the kernel-doc style. So reformat them and link
them from the Documentation.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20220728061056.20799-5-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The GPIO uart functions are documented in Documentation. Move and
transform this documentation into kernel-doc directly in the code and
reference it in Documentation using kernel-doc:.
This makes it easier to update, maintain and check by the build.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20220728061056.20799-3-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some of the serial (uart_*) functions are documented twice. Once as
kernel-doc along their sources and once in Documentation. So deduplicate
these texts, merge them into kernel-doc in the sources, and link them
using kernel-doc: from the Documentation.
To be properly linked and rendered, tabulators had to be removed from
the comments.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20220728061056.20799-2-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The LPUART can't distinguish between a break signal and a framing error,
so need to count the break characters if there is a framing error and
received data is zero instead of the parity error.
Fixes: 5541a9bacf ("serial: fsl_lpuart: handle break and make sysrq work")
Reviewed-by: Michael Walle <michael@walle.cc>
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Link: https://lore.kernel.org/r/20220725050115.12396-1-sherry.sun@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The info structs are local only to the stm32-usart.c driver and are
triggering sparse warnings about being undecalred. Move these into
the main driver code and make them static to avoid the following
warnings:
drivers/tty/serial/stm32-usart.h:42:25: warning: symbol 'stm32f4_info' was not declared. Should it be static?
drivers/tty/serial/stm32-usart.h:63:25: warning: symbol 'stm32f7_info' was not declared. Should it be static?
drivers/tty/serial/stm32-usart.h:85:25: warning: symbol 'stm32h7_info' was not declared. Should it be static?
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Link: https://lore.kernel.org/r/20220721212430.453192-1-ben-linux@fluff.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The LPUART hardware doesn't zero out the parity bit on the received
characters. This behavior won't impact the use cases of CS8 because
the parity bit is the 9th bit which is not currently used by software.
But the parity bit for CS7 must be zeroed out by software in order to
get the correct raw data.
Signed-off-by: Shenwei Wang <shenwei.wang@nxp.com>
Link: https://lore.kernel.org/r/20220714185858.615373-1-shenwei.wang@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In the logic around call to clk_round_rate(), for some corner conditions,
get_clk_div_rate() could return an sub-optimal clock rate. Also, if an
exact clock rate was not found lowest clock was being returned.
Search for suitable clock rate in 2 steps
a) exact match or within 2% tolerance
b) within 5% tolerance
This also takes care of corner conditions.
Fixes: c2194bc999 ("tty: serial: qcom-geni-serial: Remove uart frequency table. Instead, find suitable frequency with call to clk_round_rate")
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Vijaya Krishna Nivarthi <quic_vnivarth@quicinc.com>
Link: https://lore.kernel.org/r/1657911343-1909-1-git-send-email-quic_vnivarth@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The error path when get clock frequency fails in bcm2835aux_serial
driver does not correctly disable the clock.
This flaw was found using a static analysis tool "Hulk Robot", which
reported the following warning when analyzing linux-next/master:
drivers/tty/serial/8250/8250_bcm2835aux.c:
warning: clk_disable_unprepare_missing.cocci
The cocci script checks for the existence of clk_disable_unprepare()
paired with clk_prepare_enable().
Add the missing clk_disable_unprepare() to the error path.
Fixes: fcc446c8aa ("serial: 8250_bcm2835aux: Add ACPI support")
Reported-by: Hulk Robot <hulkci@huawei.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Guo Mengqi <guomengqi3@huawei.com>
Link: https://lore.kernel.org/r/20220715023312.37808-1-guomengqi3@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here are some TTY and Serial driver fixes for 5.19-rc7. They resolve a
number of reported problems including:
- long time bug in pty_write() that has been reported in the
past.
- 8250 driver fixes
- new serial device ids
- vt overlapping data copy bugfix
- other tiny serial driver bugfixes
All of these have been in linux-next for a while with no reported
problems.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCYtJZSg8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ymDUQCfbfzfsMweUSiEjcfENNV4o52o3JgAn3MudgIV
y1gogwEVkYK6q5itgi3W
=ZAlt
-----END PGP SIGNATURE-----
Merge tag 'tty-5.19-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty and serial driver fixes from Greg KH:
"Here are some TTY and Serial driver fixes for 5.19-rc7. They resolve a
number of reported problems including:
- longtime bug in pty_write() that has been reported in the past.
- 8250 driver fixes
- new serial device ids
- vt overlapping data copy bugfix
- other tiny serial driver bugfixes
All of these have been in linux-next for a while with no reported
problems"
* tag 'tty-5.19-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
tty: use new tty_insert_flip_string_and_push_buffer() in pty_write()
tty: extract tty_flip_buffer_commit() from tty_flip_buffer_push()
serial: 8250: dw: Fix the macro RZN1_UART_xDMACR_8_WORD_BURST
vt: fix memory overlapping when deleting chars in the buffer
serial: mvebu-uart: correctly report configured baudrate value
serial: 8250: Fix PM usage_count for console handover
serial: 8250: fix return error code in serial8250_request_std_resource()
serial: stm32: Clear prev values before setting RTS delays
tty: Add N_CAN327 line discipline ID for ELM327 based CAN driver
serial: 8250: Fix __stop_tx() & DMA Tx restart races
serial: pl011: UPSTAT_AUTORTS requires .throttle/unthrottle
tty: serial: samsung_tty: set dma burst_size to 1
serial: 8250: dw: enable using pdata with ACPI
Commit d3164e2f3b ("MIPS: Remove VR41xx support") removed support
for MIPS VR41xx platform, so remove exclusive drivers for this
platform, too.
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Link: https://lore.kernel.org/r/20220715140322.135825-1-tsbogend@alpha.franken.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Before the drivers rs485_config() function is called the serial core
already ensures that only one of both options RTS on send or RTS after send
is set. So remove the concerning sanity check in the driver function to
avoid redundancy.
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Lino Sanfilippo <l.sanfilippo@kunbus.com>
Link: https://lore.kernel.org/r/20220710164442.2958979-9-LinoSanfilippo@gmx.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Before the drivers rs485_config() function is called the serial core
already ensures that only one of both options RTS on send or RTS after send
is set. So remove the concerning sanity check in the driver function to
avoid redundancy.
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Lino Sanfilippo <l.sanfilippo@kunbus.com>
Link: https://lore.kernel.org/r/20220710164442.2958979-8-LinoSanfilippo@gmx.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently the RTS delays set via device tree are not clamped to a maximum
value although the device tree bindings documentation for RS485 claims that
only a maximum of 1000 msecs is allowed.
So clamp the values to avoid arbitrary high delay settings. However clamp
the values to 100 instead of 1000 msecs to be consistent which the maximum
that is allowed when setting the delays from userspace via the UART ioctl
TIOCSRS485.
Signed-off-by: Lino Sanfilippo <l.sanfilippo@kunbus.com>
Link: https://lore.kernel.org/r/20220710164442.2958979-6-LinoSanfilippo@gmx.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Move the sanitizing of RS485 delays out of uart_sanitize_serial_rs485()
into the new function uart_sanitize_serial_rs485_delays().
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Lino Sanfilippo <l.sanfilippo@kunbus.com>
Link: https://lore.kernel.org/r/20220710164442.2958979-5-LinoSanfilippo@gmx.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In serial8250_em485_config() the termination GPIO is set with the uart_port
spinlock held. This is an issue if setting the GPIO line can sleep (e.g.
since the concerning GPIO expander is connected via SPI or I2C).
Fix this by setting the termination line outside of the uart_port spinlock
in the serial core and using gpiod_set_value_cansleep() which instead of
gpiod_set_value() allows it to sleep.
Beside fixing the termination GPIO line setting for the 8250 driver this
change also makes setting the termination GPIO generic for all UART
drivers.
Signed-off-by: Lino Sanfilippo <l.sanfilippo@kunbus.com>
Link: https://lore.kernel.org/r/20220710164442.2958979-4-LinoSanfilippo@gmx.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In ar933x_config_rs485() the check for the RTS GPIO is not needed since in
case the GPIO is not available at driver init ar933x_no_rs485 is assigned
to port->rs485_supported and this function is never called. So remove the
check.
Also in uart_set_rs485_config() the serial core already assigns the passed
serial_rs485 struct to the uart port. So remove the assignment in the
drivers rs485_config() function to avoid redundancy.
Signed-off-by: Lino Sanfilippo <l.sanfilippo@kunbus.com>
Link: https://lore.kernel.org/r/20220710164442.2958979-3-LinoSanfilippo@gmx.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
RS485 is not possible without an RTS GPIO regardless of whether RS485 is
enabled at boot time or not. So correct the concerning check in the probe()
function.
Fixes: e849145e1f ("serial: ar933x: Fill in rs485_supported")
Signed-off-by: Lino Sanfilippo <l.sanfilippo@kunbus.com>
Link: https://lore.kernel.org/r/20220710164442.2958979-2-LinoSanfilippo@gmx.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 9cabe26e65 ("serial: 8250_bcm7271: UART errors after resuming
from S2") prevented an early enabling of RTS during resume, but it did
not actively restore the RTS state after resume.
Fixes: 9cabe26e65 ("serial: 8250_bcm7271: UART errors after resuming from S2")
Signed-off-by: Doug Berger <opendmb@gmail.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20220714031316.404918-1-f.fainelli@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
With PSLVERR_RESP_EN parameter set to 1, the device generates an error
response when an attempt to read an empty RBR with FIFO enabled.
This happens when LCR writes are ignored when UART is busy.
dw8250_check_lcr() in retries to update LCR, invokes dw8250_force_idle()
to clear and reset FIFO and eventually reads UART_RX causing the error.
Avoid this by not reading RBR/UART_RX when no data is available.
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: VAMSHI GAJJELA <vamshigajjela@google.com>
Link: https://lore.kernel.org/r/20220713131722.2316829-1-vamshigajjela@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
S3C2410_UCON is a 32bit register, so it must be read with rd_regl()
instead of rd_reg(), otherwise the upper bits will be zeroed. Fix this.
Fixes: 72a43046b6 ("tty: serial: samsung_tty: loopback mode support")
Tested-by: Chanho Park <chanho61.park@samsung.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Chanho Park <chanho61.park@samsung.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Link: https://lore.kernel.org/r/20220712140745.30362-1-m.szyprowski@samsung.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Aspeed Virtual UART is only present on Aspeed BMC platforms. Hence
add a dependency on ARCH_ASPEED, to prevent asking the user about this
driver when configuring a kernel without Aspeed BMC support.
Reviewed-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/259138c372d433005b4871789ef9ee8d15320307.1657528861.git.geert+renesas@glider.be
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add support for some of the Brainboxes PCIe (PX) range of
serial cards, including the PX-101, PX-235/PX-246,
PX-203/PX-257, PX-260/PX-701, PX-310, PX-313,
PX-320/PX-324/PX-376/PX-387, PX-335/PX-346, PX-368, PX-420,
PX-803 and PX-846.
Signed-off-by: Cameron Williams <cang1@live.co.uk>
Cc: stable <stable@kernel.org>
Link: https://lore.kernel.org/r/AM5PR0202MB2564669252BDC59BF55A6E87C4879@AM5PR0202MB2564.eurprd02.prod.outlook.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
pull the following:
- Julia fixes a typo in the Broadcom STB legacy power management code
- Liang fixes a device_node reference count leak in the Broadcom STB BIU
driver code error path(s)
- Nicolas and Stefan provide updates to the BCM2835 power management
driver allowing its use on BCM2711 (Raspberry Pi 4) and to enable the
use of the V3D GPU driver on such platforms. This is a merge of an
immutable branch from Lee Jones' MFD tree
- William removes the use of CONFIG_ARCH_BCM_63XX which is removed and
replaces the dependencies with CONFIG_ARCH_BCMBCA which is how all of
the DSL/PON SoCs from Broadcom are now supported in the upstream
kernel.
-----BEGIN PGP SIGNATURE-----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=O/9g
-----END PGP SIGNATURE-----
gpgsig -----BEGIN PGP SIGNATURE-----
iQIzBAABCgAdFiEEo6/YBQwIrVS28WGKmmx57+YAGNkFAmLN4J0ACgkQmmx57+YA
GNnFBQ/8CMZHB963Azx+ybxj95ClLjtKKio7IjQRr4YoawXHYdNipLumrBS3V7BZ
qu432X9gGHC5QP4U46d4zHUvWeLqPwsns6WnTa8wwbY2kAccnoCtOaVyWM8O2YyS
n7Zwq6wSEul6GT7ig+eEsZ5NFhC3+i1C/mqCZfcEGWrIfzse5UwKVmcG/dmnavIP
NtmaWMWr2PUvF3VJpgn71JpWJegkyANjDi7JJC/71h5MzjNrpGsE3XG5QyLpQfRZ
+lAxT+2zJNbk+eSnISg1bpaeL/S9F8vrmzpgMEcCcydcpgQQ7I/M9nx+mNAbpRwn
c7DuoXYB9VNX6bsI0pUjavhMc3qAIPtgYknGe/WhAmS6D4y/IfTJ7L91irULH/gC
ZDH2aDTblhtefiSgd8X9RJyRTZb0CtTUoSR2ST0SfpMI8xJaaswXBS7nYfLib08v
pSLAU6qalUpJpJ+ADeSEIbfUjuGR6GR1iT1R4dpdp3NfhR8u6bPdkphxzwdzctBL
bZ+ZcFMlAfSp07FzII+2Ce5fuT5qM7rdqKurL5WFmJOYIHfqGDTESWp5vvViAHPJ
2c+ONWnPvMXoKxC6d90E8AhOhvOeE1frfu5NWJtzU7OY98rI1J5nFEF9hmVQWZ3p
hfEzP+wiBuN2mHRDNtgmmJFFhbzPdXlY5QafR2XDm1kpfuFh/cY=
=yTZT
-----END PGP SIGNATURE-----
Merge tag 'arm-soc/for-5.20/drivers' of https://github.com/Broadcom/stblinux into arm/drivers
This pull request contains Broadcom SoC drivers updatse for 5.20, please
pull the following:
- Julia fixes a typo in the Broadcom STB legacy power management code
- Liang fixes a device_node reference count leak in the Broadcom STB BIU
driver code error path(s)
- Nicolas and Stefan provide updates to the BCM2835 power management
driver allowing its use on BCM2711 (Raspberry Pi 4) and to enable the
use of the V3D GPU driver on such platforms. This is a merge of an
immutable branch from Lee Jones' MFD tree
- William removes the use of CONFIG_ARCH_BCM_63XX which is removed and
replaces the dependencies with CONFIG_ARCH_BCMBCA which is how all of
the DSL/PON SoCs from Broadcom are now supported in the upstream
kernel.
* tag 'arm-soc/for-5.20/drivers' of https://github.com/Broadcom/stblinux:
tty: serial: bcm63xx: bcmbca: Replace ARCH_BCM_63XX with ARCH_BCMBCA
spi: bcm63xx-hsspi: bcmbca: Replace ARCH_BCM_63XX with ARCH_BCMBCA
clk: bcm: bcmbca: Replace ARCH_BCM_63XX with ARCH_BCMBCA
hwrng: bcm2835: bcmbca: Replace ARCH_BCM_63XX with ARCH_BCMBCA
phy: brcm-sata: bcmbca: Replace ARCH_BCM_63XX with ARCH_BCMBCA
i2c: brcmstb: bcmbca: Replace ARCH_BCM_63XX with ARCH_BCMBCA
ata: ahci_brcm: bcmbca: Replace ARCH_BCM_63XX with ARCH_BCMBCA
soc: bcm: bcm2835-power: Bypass power_on/off() calls
soc: bcm: bcm2835-power: Add support for BCM2711's RPiVid ASB
soc: bcm: bcm2835-power: Resolve ASB register macros
soc: bcm: bcm2835-power: Refactor ASB control
mfd: bcm2835-pm: Add support for BCM2711
mfd: bcm2835-pm: Use 'reg-names' to get resources
soc: bcm: brcmstb: biuctrl: Add missing of_node_put()
soc: bcm: brcmstb: pm: pm-arm: fix typo in comment
Link: https://lore.kernel.org/r/20220711164451.3542127-6-f.fainelli@gmail.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Prepare for the BCM63138 ARCH_BCM_63XX migration to ARCH_BCMBCA. Make
SERIAL_BCM63XX depending on ARCH_BCMBCA.
Signed-off-by: William Zhang <william.zhang@broadcom.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
There is a race in pty_write(). pty_write() can be called in parallel
with e.g. ioctl(TIOCSTI) or ioctl(TCXONC) which also inserts chars to
the buffer. Provided, tty_flip_buffer_push() in pty_write() is called
outside the lock, it can commit inconsistent tail. This can lead to out
of bounds writes and other issues. See the Link below.
To fix this, we have to introduce a new helper called
tty_insert_flip_string_and_push_buffer(). It does both
tty_insert_flip_string() and tty_flip_buffer_commit() under the port
lock. It also calls queue_work(), but outside the lock. See
71a174b39f (pty: do tty_flip_buffer_push without port->lock in
pty_write) for the reasons.
Keep the helper internal-only (in drivers' tty.h). It is not intended to
be used widely.
Link: https://seclists.org/oss-sec/2022/q2/155
Fixes: 71a174b39f (pty: do tty_flip_buffer_push without port->lock in pty_write)
Cc: 一只狗 <chennbnbnb@gmail.com>
Cc: Dan Carpenter <dan.carpenter@oracle.com>
Suggested-by: Hillf Danton <hdanton@sina.com>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20220707082558.9250-2-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We will need this new helper in the next patch.
Cc: Hillf Danton <hdanton@sina.com>
Cc: 一只狗 <chennbnbnb@gmail.com>
Cc: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20220707082558.9250-1-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
gsmld_poll() currently fails to handle the following corner cases correctly:
- remote party closed the associated tty
Add the missing checks and map those to EPOLLHUP.
Reorder the checks to group them by their reaction.
Fixes: e1eaea46bb ("tty: n_gsm line discipline")
Signed-off-by: Daniel Starke <daniel.starke@siemens.com>
Link: https://lore.kernel.org/r/20220707113223.3685-4-daniel.starke@siemens.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The current implementation constipates all transmission paths during flow
control except for flow control frames. However, these may not be located
at the beginning of the transmission queue of the control channel.
Ensure that flow control frames in the transmission queue for the control
channel are always handled even if constipated by skipping through other
messages.
Fixes: 0af021678d ("tty: n_gsm: fix deadlock and link starvation in outgoing data path")
Signed-off-by: Daniel Starke <daniel.starke@siemens.com>
Link: https://lore.kernel.org/r/20220707113223.3685-3-daniel.starke@siemens.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
n_gsm is based on the 3GPP 07.010 and its newer version is the 3GPP 27.010.
See https://portal.3gpp.org/desktopmodules/Specifications/SpecificationDetails.aspx?specificationId=1516
The changes from 07.010 to 27.010 are non-functional. Therefore, I refer to
the newer 27.010 here. Chapter 5.3.3 defines the DM response. There exists
no DM command. However, the current implementation incorrectly sends DM as
command in case of unexpected UIH frames in gsm_queue().
Correct this behavior by always sending DM as response.
Fixes: e1eaea46bb ("tty: n_gsm line discipline")
Signed-off-by: Daniel Starke <daniel.starke@siemens.com>
Link: https://lore.kernel.org/r/20220707113223.3685-2-daniel.starke@siemens.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
n_gsm is based on the 3GPP 07.010 and its newer version is the 3GPP 27.010.
See https://portal.3gpp.org/desktopmodules/Specifications/SpecificationDetails.aspx?specificationId=1516
The changes from 07.010 to 27.010 are non-functional. Therefore, I refer to
the newer 27.010 here. Chapter 5.7.3 states that the valid range for the
maximum number of retransmissions (N2) is from 0 to 255 (both including).
gsm_dlci_t1() handles this number incorrectly by performing N2 - 1
retransmission attempts. Setting N2 to zero results in more than 255
retransmission attempts.
Fix gsm_dlci_t1() to comply with 3GPP 27.010.
Fixes: e1eaea46bb ("tty: n_gsm line discipline")
Signed-off-by: Daniel Starke <daniel.starke@siemens.com>
Link: https://lore.kernel.org/r/20220707113223.3685-1-daniel.starke@siemens.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When DT provides rs485-term, set termination flag as supported.
Reviewed-by: Lino Sanfilippo <l.sanfilippo@kunbus.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20220704094515.6831-3-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Embed rs485_supported to uart_port to allow serial core to tweak it as
needed.
Reviewed-by: Lino Sanfilippo <l.sanfilippo@kunbus.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20220704094515.6831-2-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some Freescale 8250 implementations have the problem that a single long
break results in one irq per character frame time. The code in
fsl8250_handle_irq() that is supposed to handle that uses the BI bit in
lsr_saved_flags to detect such a situation and then skip the second
received character. However it also stores other error bits and so after
a single frame error the character received in the next irq handling is
passed to the upper layer with a frame error, too.
So after a spike on the data line (which is correctly recognized as a
frame error) the following valid character is thrown away, because the
driver reports a frame error for that one, too.
To weaken this problem restrict saving LSR to only the BI bit.
Note however that the handling is still broken:
- lsr_saved_flags is updated using orig_lsr which is the LSR content
for the first received char, but there might be more in the FIFO, so
a character is thrown away that is received later and not necessarily
the one following the break.
- The doubled break might be the 2nd and 3rd char in the FIFO, so the
workaround doesn't catch these, because serial8250_rx_chars() doesn't
handle the workaround.
- lsr_saved_flags might have set UART_LSR_BI at the entry of
fsl8250_handle_irq() which doesn't originate from
fsl8250_handle_irq()'s "up->lsr_saved_flags |= orig_lsr &
UART_LSR_BI;" but from e.g. from serial8250_tx_empty().
- For a long or a short break this isn't about two characters, but more
or only a single one.
Fixes: 9deaa53ac7 ("serial: add irq handler for Freescale 16550 errata.")
Acked-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20220704085119.55900-1-u.kleine-koenig@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Within gsm_activate_mux() all timers and locks are initiated before the
actual resource for the control channel is allocated. This can lead to race
conditions.
Allocate the control channel DLCI object first to avoid race conditions.
Fixes: e1eaea46bb ("tty: n_gsm line discipline")
Signed-off-by: Daniel Starke <daniel.starke@siemens.com>
Link: https://lore.kernel.org/r/20220701122332.2039-2-daniel.starke@siemens.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The current implementation queues up new control and user packets as needed
and processes this queue down to the ldisc in the same code path.
That means that the upper and the lower layer are hard coupled in the code.
Due to this deadlocks can happen as seen below while transmitting data,
especially during ldisc congestion. Furthermore, the data channels starve
the control channel on high transmission load on the ldisc.
Introduce an additional control channel data queue to prevent timeouts and
link hangups during ldisc congestion. This is being processed before the
user channel data queue in gsm_data_kick(), i.e. with the highest priority.
Put the queue to ldisc data path into a workqueue and trigger it whenever
new data has been put into the transmission queue. Change
gsm_dlci_data_sweep() accordingly to fill up the transmission queue until
TX_THRESH_HI. This solves the locking issue, keeps latency low and provides
good performance on high data load.
Note that now all packets from a DLCI are removed from the internal queue
if the associated DLCI was closed. This ensures that no data is sent by the
introduced write task to an already closed DLCI.
BUG: spinlock recursion on CPU#0, test_v24_loop/124
lock: serial8250_ports+0x3a8/0x7500, .magic: dead4ead, .owner: test_v24_loop/124, .owner_cpu: 0
CPU: 0 PID: 124 Comm: test_v24_loop Tainted: G O 5.18.0-rc2 #3
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.15.0-1 04/01/2014
Call Trace:
<IRQ>
dump_stack_lvl+0x34/0x44
do_raw_spin_lock+0x76/0xa0
_raw_spin_lock_irqsave+0x72/0x80
uart_write_room+0x3b/0xc0
gsm_data_kick+0x14b/0x240 [n_gsm]
gsmld_write_wakeup+0x35/0x70 [n_gsm]
tty_wakeup+0x53/0x60
tty_port_default_wakeup+0x1b/0x30
serial8250_tx_chars+0x12f/0x220
serial8250_handle_irq.part.0+0xfe/0x150
serial8250_default_handle_irq+0x48/0x80
serial8250_interrupt+0x56/0xa0
__handle_irq_event_percpu+0x78/0x1f0
handle_irq_event+0x34/0x70
handle_fasteoi_irq+0x90/0x1e0
__common_interrupt+0x69/0x100
common_interrupt+0x48/0xc0
asm_common_interrupt+0x1e/0x40
RIP: 0010:__do_softirq+0x83/0x34e
Code: 2a 0a ff 0f b7 ed c7 44 24 10 0a 00 00 00 48 c7 c7 51 2a 64 82 e8 2d
e2 d5 ff 65 66 c7 05 83 af 1e 7e 00 00 fb b8 ff ff ff ff <49> c7 c2 40 61
80 82 0f bc c5 41 89 c4 41 83 c4 01 0f 84 e6 00 00
RSP: 0018:ffffc90000003f98 EFLAGS: 00000286
RAX: 00000000ffffffff RBX: 0000000000000000 RCX: 0000000000000000
RDX: 0000000000000000 RSI: ffffffff82642a51 RDI: ffffffff825bb5e7
RBP: 0000000000000200 R08: 00000008de3271a8 R09: 0000000000000000
R10: 0000000000000001 R11: 0000000000000000 R12: 0000000000000000
R13: 0000000000000030 R14: 0000000000000000 R15: 0000000000000000
? __do_softirq+0x73/0x34e
irq_exit_rcu+0xb5/0x100
common_interrupt+0xa4/0xc0
</IRQ>
<TASK>
asm_common_interrupt+0x1e/0x40
RIP: 0010:_raw_spin_unlock_irqrestore+0x2e/0x50
Code: 00 55 48 89 fd 48 83 c7 18 53 48 89 f3 48 8b 74 24 10 e8 85 28 36 ff
48 89 ef e8 cd 58 36 ff 80 e7 02 74 01 fb bf 01 00 00 00 <e8> 3d 97 33 ff
65 8b 05 96 23 2b 7e 85 c0 74 03 5b 5d c3 0f 1f 44
RSP: 0018:ffffc9000020fd08 EFLAGS: 00000202
RAX: 0000000000000000 RBX: 0000000000000246 RCX: 0000000000000000
RDX: 0000000000000004 RSI: ffffffff8257fd74 RDI: 0000000000000001
RBP: ffff8880057de3a0 R08: 00000008de233000 R09: 0000000000000000
R10: 0000000000000001 R11: 0000000000000000 R12: 0000000000000000
R13: 0000000000000100 R14: 0000000000000202 R15: ffff8880057df0b8
? _raw_spin_unlock_irqrestore+0x23/0x50
gsmtty_write+0x65/0x80 [n_gsm]
n_tty_write+0x33f/0x530
? swake_up_all+0xe0/0xe0
file_tty_write.constprop.0+0x1b1/0x320
? n_tty_flush_buffer+0xb0/0xb0
new_sync_write+0x10c/0x190
vfs_write+0x282/0x310
ksys_write+0x68/0xe0
do_syscall_64+0x3b/0x90
entry_SYSCALL_64_after_hwframe+0x44/0xae
RIP: 0033:0x7f3e5e35c15c
Code: 8b 7c 24 08 89 c5 e8 c5 ff ff ff 89 ef 89 44 24 08 e8 58 bc 02 00 8b
44 24 08 48 83 c4 10 5d c3 48 63 ff b8 01 00 00 00 0f 05 <48> 3d 00 f0 ff
ff 76 10 48 8b 15 fd fc 05 00 f7 d8 64 89 02 48 83
RSP: 002b:00007ffcee77cd18 EFLAGS: 00000246 ORIG_RAX: 0000000000000001
RAX: ffffffffffffffda RBX: 00007ffcee77cd70 RCX: 00007f3e5e35c15c
RDX: 0000000000000100 RSI: 00007ffcee77cd90 RDI: 0000000000000003
RBP: 0000000000000100 R08: 0000000000000000 R09: 7efefefefefefeff
R10: 00007f3e5e3bddeb R11: 0000000000000246 R12: 00007ffcee77ce8f
R13: 0000000000000001 R14: 000056214404e010 R15: 00007ffcee77cd90
</TASK>
Fixes: e1eaea46bb ("tty: n_gsm line discipline")
Signed-off-by: Daniel Starke <daniel.starke@siemens.com>
Link: https://lore.kernel.org/r/20220701122332.2039-1-daniel.starke@siemens.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The function may be used by the user directly and also by the n_gsm
internal functions. They can lead into a race condition which results in
interleaved frames if both are writing at the same time. The receiving side
is not able to decode those interleaved frames correctly.
Add a lock around the low side tty write to avoid race conditions and frame
interleaving between user originated writes and n_gsm writes.
Fixes: e1eaea46bb ("tty: n_gsm line discipline")
Signed-off-by: Daniel Starke <daniel.starke@siemens.com>
Link: https://lore.kernel.org/r/20220701061652.39604-9-daniel.starke@siemens.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In the current implementation control packets are re-transmitted even if
the control channel closed down during T2. This is wrong.
Check whether the control channel is open before re-transmitting any
packets. Note that control channel open/close is handled by T1 and not T2
and remains unaffected by this.
Fixes: e1eaea46bb ("tty: n_gsm line discipline")
Signed-off-by: Daniel Starke <daniel.starke@siemens.com>
Link: https://lore.kernel.org/r/20220701061652.39604-7-daniel.starke@siemens.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
n_gsm is based on the 3GPP 07.010 and its newer version is the 3GPP 27.010.
See https://portal.3gpp.org/desktopmodules/Specifications/SpecificationDetails.aspx?specificationId=1516
The changes from 07.010 to 27.010 are non-functional. Therefore, I refer to
the newer 27.010 here. Chapter 5.4.6.3.6 states that FCoff stops the
transmission on all channels except the control channel. This is already
implemented in gsm_data_kick(). However, chapter 5.4.8.1 explains that this
shall result in the same behavior as software flow control on the ldisc in
advanced option mode. That means only flow control frames shall be sent
during flow off. The current implementation does not consider this case.
Change gsm_data_kick() to send only flow control frames if constipated to
abide the standard. gsm_read_ea_val() and gsm_is_flow_ctrl_msg() are
introduced as helper functions for this.
It is planned to use gsm_read_ea_val() in later code cleanups for other
functions, too.
Fixes: c01af4fec2 ("n_gsm : Flow control handling in Mux driver")
Signed-off-by: Daniel Starke <daniel.starke@siemens.com>
Link: https://lore.kernel.org/r/20220701061652.39604-5-daniel.starke@siemens.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The current implementation does not handle the situation that no data is in
the internal queue and needs to be sent out while the user tty fifo is
full.
Add a timer that moves more data from user tty down to the internal queue
which is then serialized on the ldisc. This timer is triggered if no data
was moved from a user tty to the internal queue within 10 * T1.
Fixes: e1eaea46bb ("tty: n_gsm line discipline")
Signed-off-by: Daniel Starke <daniel.starke@siemens.com>
Link: https://lore.kernel.org/r/20220701061652.39604-4-daniel.starke@siemens.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
1) The function drains the fifo for the given user tty/DLCI without
considering 'TX_THRESH_HI' and different to gsm_dlci_data_output_framed(),
which moves only one packet from the user side to the internal transmission
queue. We can only handle one packet at a time here if we want to allow
DLCI priority handling in gsm_dlci_data_sweep() to avoid link starvation.
2) Furthermore, the additional header octet from convergence layer type 2
is not counted against MTU. It is part of the UI/UIH frame message which
needs to be limited to MTU. Hence, it is wrong not to consider this octet.
3) Finally, the waiting user tty is not informed about freed space in its
send queue.
Take at most one packet worth of data out of the DLCI fifo to fix 1).
Limit the max user data size per packet to MTU - 1 in case of convergence
layer type 2 to leave space for the control signal octet which is added in
the later part of the function. This fixes 2).
Add tty_port_tty_wakeup() to wake up the user tty if new write space has
been made available to fix 3).
Fixes: 268e526b93 ("tty/n_gsm: avoid fifo overflow in gsm_dlci_data_output")
Signed-off-by: Daniel Starke <daniel.starke@siemens.com>
Link: https://lore.kernel.org/r/20220701061652.39604-3-daniel.starke@siemens.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The current implementation registers/deregisters the user ttys at mux
attach/detach. That means that the user devices are available before any
control channel is open. However, user channel initialization requires an
open control channel. Furthermore, the user is not informed if the mux
restarts due to configuration changes.
Put the registration/deregistration procedure into separate function to
improve readability.
Move registration to mux activation and deregistration to mux cleanup to
keep the user devices only open as long as a control channel exists. The
user will be informed via the device driver if the mux was reconfigured in
a way that required a mux re-activation.
This makes it necessary to add T2 initialization to gsmld_open() for the
ldisc open code path (not the reconfiguration code path) to avoid deletion
of an uninitialized T2 at mux cleanup.
Fixes: d50f6dcaf2 ("tty: n_gsm: expose gsmtty device nodes at ldisc open time")
Signed-off-by: Daniel Starke <daniel.starke@siemens.com>
Link: https://lore.kernel.org/r/20220701061652.39604-2-daniel.starke@siemens.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Linus Torvalds
Douglas Anderson
Jason Wang
Jiri Slaby
Narendra Hadke
Sherry Sun
Ben Dooks
Shenwei Wang
Vijaya Krishna Nivarthi
Guo Mengqi
Tetsuo Handa
Thomas Bogendoerfer
Lino Sanfilippo
Doug Berger
VAMSHI GAJJELA
Marek Szyprowski
Geert Uytterhoeven
Cameron Williams
Arnd Bergmann
William Zhang
Daniel Starke
Ilpo Järvinen
Uwe Kleine-König