The multi queue support is still disabled by default for the bnx2x
(needs some more testing and validation), but there are 2 obvious bug in
it which are fixed in this patch
Signed-off-by: Yitchak Gertner <gertner@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixing the order of enabling and disabling NAPI and the interrupts
Signed-off-by: Yitchak Gertner <gertner@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Load failures were not handled correctly
Signed-off-by: Yitchak Gertner <gertner@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The TPA initialization is part of the FW internal memory initialization
and so it is moved to the appropriate function
Signed-off-by: Yitchak Gertner <gertner@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Increasing the lock timeout to 5 seconds instead of 1 second to minimize
the chance of failures due to timeout
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After iSCSI boot, the HW lock should only protect the flag so only the
first function will reset the chip and not then entire chip reset
process
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The A1021G board is also using the fan failure mechanism in the same way
the A1022G board does
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The has Rx work check was wrong: when the FW was at the end of the page,
the driver was already at the beginning of the next page. Since the
check only validated that both driver and FW are pointing to the same
place, it concluded that there is still work to be done. This caused
some serious issues including long latency results on ping-pong test and
lockups while unloading the driver in that condition.
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The drivers below do not use LINUX_VERSION_CODE nor KERNEL_VERSION.
drivers/net/acenic.c
drivers/net/bnx2x_link.c
drivers/net/bnx2x_main.c
drivers/net/cpmac.c
drivers/net/gianfar_sysfs.c
drivers/net/ipg.h
drivers/net/ppp_mppe.c
drivers/net/pppol2tp.c
drivers/net/r6040.c
drivers/net/sh_eth.c
drivers/net/sky2.c
drivers/net/tehuti.h
drivers/net/typhoon.c
This patch removes the said #include <linux/version.h>.
Signed-off-by: Huang Weiyi <hwy@cn.fujitsu.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Checkpatch compliance
The latest version of checkpatch found the following style errors in the
code
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Spelling mistakes
Spelling has to L's in it...
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Minor code improvements
Small changes to make the code a little bit more efficient and mostly
more readable:
- Using unified macros for EMAC_RD/WR which looks like normal REG_RD/WR
- Removing the NIG_WR since it did nothing and was only confusing
- On bnx2x_panic_dump, print only the used parts of the rings
- define parameters only on the branch they are needed and not at the
beginning of the function
- using NETIF_MSG_INTR and not private BNX2X_MSG_SP for debug prints
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Driver info
The internal FW which is downloaded by the driver should not be
displayed - it is only causing confusion and it is redundant since it
can be concluded from the driver version. Display only FW which is
burned on the board nvram
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
8073 PHY changes
The initial support we had for this PHY needs some serious changing. The
major change is that this PHY should be initialized only when the first
function is loaded and not for each function. The official SPI-ROM of
this PHY was released and it requires some changes in the initialization
code as well
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change GPIO for any port
The set GPIO function should receive the port index to allow changing
the GPIO of another port. This is needed for the common init phase (one
the first driver is loaded for the chip)
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pause settings
- 1G pause was not working due to missing write to the emac block
(TX_MODE_FLOW_EN)
- The flow control should use the negotiated result (after autoneg) so
we should save both the requested autoneg and the result
- The HW credits with flow control at 1G speed were not optimized and
caused low throughput
- It is recommended to turn off flow control if the MTU is bigger than
5000B due to internal buffers size
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
No LRO without Rx checksum
Disabling LRO when Rx checksum is disabled
Signed-off-by: Vladislav Zolotarov <vladz@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Wrong structure size
The wrong structure was used in the sizeof to clear (luckily both
structures have the same size in this version...)
Signed-off-by: Yitchak Gertner <gertner@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
WoL capability
All designs reported WoL capability regardless of HW limitations - check
if this device is actually capable of WoL
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Clearing MAC addresses filters
When the driver unloads, it should clear the MAC addresses filters in
the HW - this prevents packets from entering the chip when the driver is
re-loaded before initializing the right filters
Signed-off-by: Yitchak Gertner <gertner@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Delay in while loops
The delay in the loop should be after the change. This has very little
effect (can save one delay) but it is the right thing to do
Signed-off-by: Yitchak Gertner <gertner@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
PBA Table Page Alignment Workaround
The PBA table starts on the middle of the page and that's causing very
low performance with virtualization. The solution is not to update via
the BAR directly but via chip access to the same memory
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Self-test false positive
- The memory test should use a mask according to the chip type
- In the register test, check the port only once and not inside the for
loop (not causing a failure - just ugly)
Signed-off-by: Yitchak Gertner <gertner@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Memory allocation
- The CQE ring was allocated to the max size even for a chip that does
not support it. Fixed to allocate according to the chip type to save
memory
- The rx_page_ring was not freed on driver unload
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
HW attention lock
Making sure that only one function will handle the HW attention. This
makes the device parameter aeu_mask redundant so it is removed
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
HW lock mechanism
Enhancing the HW lock to work per function and not only per port - this
is needed for the next patch that protects races over HW attention
detection between the different functions. At this chance, changing the
functions names to be more inline with the current naming convention
Signed-off-by: Yitchak Gertner <gertner@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Load/Unload under traffic
Few issues were found when loading and unloading under traffic:
- When receiving Tx interrupt call netif_wake_queue if the queue is
stopped but the state is open
- Check that interrupts are enabled before doing anything else on the
msix_fp_int function
- In nic_load, enable the interrupts only when needed and ready for it
- Function stop_leading returns status since it can fail
- Add 1ms delay when unloading the driver to validate that there are no
open transactions that already started by the FW
- Splitting the "has work" function into Tx and Rx so the same function
will be used on unload and interrupts
- Do not request for WoL if only resetting the device (save the time
that it takes the FW to set the link after reset)
- Fixing the device reset after iSCSI boot and before driver load - all
internal buffers must be cleared before the driver is loaded
Signed-off-by: Vladislav Zolotarov <vladz@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
FW Internal Memory structure
The FW uses data structures on the chip internal memory to aggregate the
connections when TPA is enabled. The driver was clearing the wrong offsets
and therefore one function could cause another function to loose packets.
Changing the initialization of the chip internal memory to clear only the
relevant memory for each function which is being loaded
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Statistics
- Making sure that each drop is accounted for in the driver statistics
- Clearing the FW statistics when driver is loaded to prevent
inconsistency with HW statistics
- Once error is detected (bnx2x_panic_dump), stop the statistics
before other actions (currently it is stopped last and can corrupt
the data) - Adding HW checksum error counter to the statistics
- Removing unused variable stats_ticks
- Using macros instead of magic numbers to indicate which statistics are
shared per port and which are per function
Signed-off-by: Yitchak Gertner <gertner@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Not dropping packets with L3/L4 checksum error
Those packets should be passed to the OS. The problem is clear in
forwarding mode.
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
FW (bootcode) interface fixes
- Making sure that the device will not cause kernel panic of the
bootcode is corrupted or missing
- Removing module debug parameter "nomcp" since no one should work
without the bootcode (this is a left over from the chip bring up days)
- Instead of waiting fix amount of time for bootcode response, sample it
every 10ms (usually the answer is ready after less than 10ms)
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix dubious logical operation that was found by sparse:
linux-next-20080807/drivers/net/bnx2x_main.c:7205:27: warning: dubious: !x & y
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6:
netns: fix ip_rt_frag_needed rt_is_expired
netfilter: nf_conntrack_extend: avoid unnecessary "ct->ext" dereferences
netfilter: fix double-free and use-after free
netfilter: arptables in netns for real
netfilter: ip{,6}tables_security: fix future section mismatch
selinux: use nf_register_hooks()
netfilter: ebtables: use nf_register_hooks()
Revert "pkt_sched: sch_sfq: dump a real number of flows"
qeth: use dev->ml_priv instead of dev->priv
syncookies: Make sure ECN is disabled
net: drop unused BUG_TRAP()
net: convert BUG_TRAP to generic WARN_ON
drivers/net: convert BUG_TRAP to generic WARN_ON
Add per-device dma_mapping_ops support for CONFIG_X86_64 as POWER
architecture does:
This enables us to cleanly fix the Calgary IOMMU issue that some devices
are not behind the IOMMU (http://lkml.org/lkml/2008/5/8/423).
I think that per-device dma_mapping_ops support would be also helpful for
KVM people to support PCI passthrough but Andi thinks that this makes it
difficult to support the PCI passthrough (see the above thread). So I
CC'ed this to KVM camp. Comments are appreciated.
A pointer to dma_mapping_ops to struct dev_archdata is added. If the
pointer is non NULL, DMA operations in asm/dma-mapping.h use it. If it's
NULL, the system-wide dma_ops pointer is used as before.
If it's useful for KVM people, I plan to implement a mechanism to register
a hook called when a new pci (or dma capable) device is created (it works
with hot plugging). It enables IOMMUs to set up an appropriate
dma_mapping_ops per device.
The major obstacle is that dma_mapping_error doesn't take a pointer to the
device unlike other DMA operations. So x86 can't have dma_mapping_ops per
device. Note all the POWER IOMMUs use the same dma_mapping_error function
so this is not a problem for POWER but x86 IOMMUs use different
dma_mapping_error functions.
The first patch adds the device argument to dma_mapping_error. The patch
is trivial but large since it touches lots of drivers and dma-mapping.h in
all the architecture.
This patch:
dma_mapping_error() doesn't take a pointer to the device unlike other DMA
operations. So we can't have dma_mapping_ops per device.
Note that POWER already has dma_mapping_ops per device but all the POWER
IOMMUs use the same dma_mapping_error function. x86 IOMMUs use device
argument.
[akpm@linux-foundation.org: fix sge]
[akpm@linux-foundation.org: fix svc_rdma]
[akpm@linux-foundation.org: build fix]
[akpm@linux-foundation.org: fix bnx2x]
[akpm@linux-foundation.org: fix s2io]
[akpm@linux-foundation.org: fix pasemi_mac]
[akpm@linux-foundation.org: fix sdhci]
[akpm@linux-foundation.org: build fix]
[akpm@linux-foundation.org: fix sparc]
[akpm@linux-foundation.org: fix ibmvscsi]
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Cc: Muli Ben-Yehuda <muli@il.ibm.com>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Avi Kivity <avi@qumranet.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Removes legacy reinvent-the-wheel type thing. The generic
machinery integrates much better to automated debugging aids
such as kerneloops.org (and others), and is unambiguous due to
better naming. Non-intuively BUG_TRAP() is actually equal to
WARN_ON() rather than BUG_ON().
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add PCI recovery functions to the driver. The initial PCI state is
also saved so the MSI state can be restored during PCI recovery.
Signed-off-by: Wendy Xiong <wendyx@us.ibm.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Added registers, memories, loopback, nvram, interrupt and link tests to
the self-test
Signed-off-by: Yitchak Gertner <gertner@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for IPv6 TSO
Re-factor the Tx code with smaller functions to increase readability.
Add linearization code in case packet is too fragmented for the
microcode to handle.
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The TPA stands for Transparent Packet Aggregation. When enabled, the FW
aggregate in-order TCP packets according to the 4-tuple match and sends
1 big packet to the driver. This packet is stored on an SGL in which
each SGE is 1 page. The FW also implements a timeout algorithm and it
honors all TCP flag, including the push flag as a trigger to halt
aggregation.
After receiving Ben Hutchings comments, we also added ethtool support,
so now, thanks to Ben's patch, when forwarding is enabled, our
aggregation is turned off using the LRO flags.
Signed-off-by: Vladislav Zolotarov <vladz@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To avoid race conditions with link up/down and driver up/down - the
statistics handling was re-written in a form of state machine.
Also supporting statistics for 57711
Signed-off-by: Yitchak Gertner <gertner@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Supporting the 57711 and 57711E - refers to in the code as E1H. The
57710 is referred to as E1.
To support the new members in the family, the bnx2x structure was
divided to 3 parts: common, port and function. These changes caused some
rearrangement in the bnx2x.h file.
A set of accessories macros were added to make access to the bnx2x
structure more readable
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This new initialization code supports the 57711 HW. It also supports
the emulation and FPGA for the 57711 and 57710 initializations values
(very small amount of code which is very helpful in the lab - less
than 30 lines).
The initialization is done via DMAE after the DMAE block is ready -
before it is ready, some of the initialization is done via PCI
configuration transactions (referred to as indirect write). A mutex
to protect the DMAE from being overlapped was added. There are few
new registers which needs to be initialized by SW - the full comment
for those registers is added to the register file. A place holder for
the 57711 (referred to as E1H) microcode was added- the microcode
itself is too big and it is split over the following 4 patches
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
New Link code:
Moving all the link related code (including the calculations, the
initialization of the MAC and PHY and the external PHY's code) into
a separated file. The changes from the code that used to be part of
bnx2x.c (now called bnx2x_main.c) are:
- Using separate structures for link inputs and link outputs to clearly
identify what was configured and what is the outcome
- Adding code to read external PHY FW version and print it as part of
ethtool -i
- Adding code to upgrade external PHY FW from ethtool -E with special
magic number - Changing the link down indication to ERR level
- Adding a lock on all PHY access to prevent an interrupt and
setting changes to overlap
- Adding support for emulation and FPGA (small chunk of code that really
helps in the lab) - Adding support for 1G on BCM8706 PHY
- Adding clear debug print incase of fan failure (the PHY type is now
"failure")
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is the rename of bnx2x.c to bnx2x_main.c.
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eilon Greenstein
Yitchak Gertner
Huang Weiyi
Yaniv Rosner
Vladislav Zolotarov
Randy Dunlap
Linus Torvalds
FUJITA Tomonori
Ilpo Järvinen
Wendy Xiong