Граф коммитов

539 Коммитов

Автор SHA1 Сообщение Дата
Mike Kravetz 5e41540c8a hugetlbfs: fix kernel BUG at fs/hugetlbfs/inode.c:444!
This bug has been experienced several times by the Oracle DB team.  The
BUG is in remove_inode_hugepages() as follows:

	/*
	 * If page is mapped, it was faulted in after being
	 * unmapped in caller.  Unmap (again) now after taking
	 * the fault mutex.  The mutex will prevent faults
	 * until we finish removing the page.
	 *
	 * This race can only happen in the hole punch case.
	 * Getting here in a truncate operation is a bug.
	 */
	if (unlikely(page_mapped(page))) {
		BUG_ON(truncate_op);

In this case, the elevated map count is not the result of a race.
Rather it was incorrectly incremented as the result of a bug in the huge
pmd sharing code.  Consider the following:

 - Process A maps a hugetlbfs file of sufficient size and alignment
   (PUD_SIZE) that a pmd page could be shared.

 - Process B maps the same hugetlbfs file with the same size and
   alignment such that a pmd page is shared.

 - Process B then calls mprotect() to change protections for the mapping
   with the shared pmd. As a result, the pmd is 'unshared'.

 - Process B then calls mprotect() again to chage protections for the
   mapping back to their original value. pmd remains unshared.

 - Process B then forks and process C is created. During the fork
   process, we do dup_mm -> dup_mmap -> copy_page_range to copy page
   tables. Copying page tables for hugetlb mappings is done in the
   routine copy_hugetlb_page_range.

In copy_hugetlb_page_range(), the destination pte is obtained by:

	dst_pte = huge_pte_alloc(dst, addr, sz);

If pmd sharing is possible, the returned pointer will be to a pte in an
existing page table.  In the situation above, process C could share with
either process A or process B.  Since process A is first in the list,
the returned pte is a pointer to a pte in process A's page table.

However, the check for pmd sharing in copy_hugetlb_page_range is:

	/* If the pagetables are shared don't copy or take references */
	if (dst_pte == src_pte)
		continue;

Since process C is sharing with process A instead of process B, the
above test fails.  The code in copy_hugetlb_page_range which follows
assumes dst_pte points to a huge_pte_none pte.  It copies the pte entry
from src_pte to dst_pte and increments this map count of the associated
page.  This is how we end up with an elevated map count.

To solve, check the dst_pte entry for huge_pte_none.  If !none, this
implies PMD sharing so do not copy.

Link: http://lkml.kernel.org/r/20181105212315.14125-1-mike.kravetz@oracle.com
Fixes: c5c99429fa ("fix hugepages leak due to pagetable page sharing")
Signed-off-by: Mike Kravetz <mike.kravetz@oracle.com>
Reviewed-by: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com>
Cc: Michal Hocko <mhocko@kernel.org>
Cc: Hugh Dickins <hughd@google.com>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: "Kirill A . Shutemov" <kirill.shutemov@linux.intel.com>
Cc: Davidlohr Bueso <dave@stgolabs.net>
Cc: Prakash Sangappa <prakash.sangappa@oracle.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2018-11-18 10:15:09 -08:00
Mike Rapoport 57c8a661d9 mm: remove include/linux/bootmem.h
Move remaining definitions and declarations from include/linux/bootmem.h
into include/linux/memblock.h and remove the redundant header.

The includes were replaced with the semantic patch below and then
semi-automated removal of duplicated '#include <linux/memblock.h>

@@
@@
- #include <linux/bootmem.h>
+ #include <linux/memblock.h>

[sfr@canb.auug.org.au: dma-direct: fix up for the removal of linux/bootmem.h]
  Link: http://lkml.kernel.org/r/20181002185342.133d1680@canb.auug.org.au
[sfr@canb.auug.org.au: powerpc: fix up for removal of linux/bootmem.h]
  Link: http://lkml.kernel.org/r/20181005161406.73ef8727@canb.auug.org.au
[sfr@canb.auug.org.au: x86/kaslr, ACPI/NUMA: fix for linux/bootmem.h removal]
  Link: http://lkml.kernel.org/r/20181008190341.5e396491@canb.auug.org.au
Link: http://lkml.kernel.org/r/1536927045-23536-30-git-send-email-rppt@linux.vnet.ibm.com
Signed-off-by: Mike Rapoport <rppt@linux.vnet.ibm.com>
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Acked-by: Michal Hocko <mhocko@suse.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Chris Zankel <chris@zankel.net>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Greentime Hu <green.hu@gmail.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Guan Xuetao <gxt@pku.edu.cn>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: "James E.J. Bottomley" <jejb@parisc-linux.org>
Cc: Jonas Bonn <jonas@southpole.se>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Ley Foon Tan <lftan@altera.com>
Cc: Mark Salter <msalter@redhat.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Matt Turner <mattst88@gmail.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Michal Simek <monstr@monstr.eu>
Cc: Palmer Dabbelt <palmer@sifive.com>
Cc: Paul Burton <paul.burton@mips.com>
Cc: Richard Kuo <rkuo@codeaurora.org>
Cc: Richard Weinberger <richard@nod.at>
Cc: Rich Felker <dalias@libc.org>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Serge Semin <fancer.lancer@gmail.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Vineet Gupta <vgupta@synopsys.com>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2018-10-31 08:54:16 -07:00
Mike Rapoport 97ad1087ef memblock: replace BOOTMEM_ALLOC_* with MEMBLOCK variants
Drop BOOTMEM_ALLOC_ACCESSIBLE and BOOTMEM_ALLOC_ANYWHERE in favor of
identical MEMBLOCK definitions.

Link: http://lkml.kernel.org/r/1536927045-23536-29-git-send-email-rppt@linux.vnet.ibm.com
Signed-off-by: Mike Rapoport <rppt@linux.vnet.ibm.com>
Acked-by: Michal Hocko <mhocko@suse.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Chris Zankel <chris@zankel.net>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Greentime Hu <green.hu@gmail.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Guan Xuetao <gxt@pku.edu.cn>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: "James E.J. Bottomley" <jejb@parisc-linux.org>
Cc: Jonas Bonn <jonas@southpole.se>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Ley Foon Tan <lftan@altera.com>
Cc: Mark Salter <msalter@redhat.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Matt Turner <mattst88@gmail.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Michal Simek <monstr@monstr.eu>
Cc: Palmer Dabbelt <palmer@sifive.com>
Cc: Paul Burton <paul.burton@mips.com>
Cc: Richard Kuo <rkuo@codeaurora.org>
Cc: Richard Weinberger <richard@nod.at>
Cc: Rich Felker <dalias@libc.org>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Serge Semin <fancer.lancer@gmail.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Vineet Gupta <vgupta@synopsys.com>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2018-10-31 08:54:16 -07:00
Mike Rapoport eb31d559f1 memblock: remove _virt from APIs returning virtual address
The conversion is done using

sed -i 's@memblock_virt_alloc@memblock_alloc@g' \
	$(git grep -l memblock_virt_alloc)

Link: http://lkml.kernel.org/r/1536927045-23536-8-git-send-email-rppt@linux.vnet.ibm.com
Signed-off-by: Mike Rapoport <rppt@linux.vnet.ibm.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Chris Zankel <chris@zankel.net>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Greentime Hu <green.hu@gmail.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Guan Xuetao <gxt@pku.edu.cn>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: "James E.J. Bottomley" <jejb@parisc-linux.org>
Cc: Jonas Bonn <jonas@southpole.se>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Ley Foon Tan <lftan@altera.com>
Cc: Mark Salter <msalter@redhat.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Matt Turner <mattst88@gmail.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Michal Hocko <mhocko@suse.com>
Cc: Michal Simek <monstr@monstr.eu>
Cc: Palmer Dabbelt <palmer@sifive.com>
Cc: Paul Burton <paul.burton@mips.com>
Cc: Richard Kuo <rkuo@codeaurora.org>
Cc: Richard Weinberger <richard@nod.at>
Cc: Rich Felker <dalias@libc.org>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Serge Semin <fancer.lancer@gmail.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Vineet Gupta <vgupta@synopsys.com>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2018-10-31 08:54:15 -07:00
Mike Kravetz 22146c3ce9 hugetlbfs: dirty pages as they are added to pagecache
Some test systems were experiencing negative huge page reserve counts and
incorrect file block counts.  This was traced to /proc/sys/vm/drop_caches
removing clean pages from hugetlbfs file pagecaches.  When non-hugetlbfs
explicit code removes the pages, the appropriate accounting is not
performed.

This can be recreated as follows:
 fallocate -l 2M /dev/hugepages/foo
 echo 1 > /proc/sys/vm/drop_caches
 fallocate -l 2M /dev/hugepages/foo
 grep -i huge /proc/meminfo
   AnonHugePages:         0 kB
   ShmemHugePages:        0 kB
   HugePages_Total:    2048
   HugePages_Free:     2047
   HugePages_Rsvd:    18446744073709551615
   HugePages_Surp:        0
   Hugepagesize:       2048 kB
   Hugetlb:         4194304 kB
 ls -lsh /dev/hugepages/foo
   4.0M -rw-r--r--. 1 root root 2.0M Oct 17 20:05 /dev/hugepages/foo

To address this issue, dirty pages as they are added to pagecache.  This
can easily be reproduced with fallocate as shown above.  Read faulted
pages will eventually end up being marked dirty.  But there is a window
where they are clean and could be impacted by code such as drop_caches.
So, just dirty them all as they are added to the pagecache.

Link: http://lkml.kernel.org/r/b5be45b8-5afe-56cd-9482-28384699a049@oracle.com
Fixes: 6bda666a03 ("hugepages: fold find_or_alloc_pages into huge_no_page()")
Signed-off-by: Mike Kravetz <mike.kravetz@oracle.com>
Acked-by: Mihcla Hocko <mhocko@suse.com>
Reviewed-by: Khalid Aziz <khalid.aziz@oracle.com>
Cc: Hugh Dickins <hughd@google.com>
Cc: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com>
Cc: "Aneesh Kumar K . V" <aneesh.kumar@linux.vnet.ibm.com>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: "Kirill A . Shutemov" <kirill.shutemov@linux.intel.com>
Cc: Davidlohr Bueso <dave@stgolabs.net>
Cc: Alexander Viro <viro@zeniv.linux.org.uk>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2018-10-26 16:38:16 -07:00
Mike Kravetz dff11abe28 hugetlb: take PMD sharing into account when flushing tlb/caches
When fixing an issue with PMD sharing and migration, it was discovered via
code inspection that other callers of huge_pmd_unshare potentially have an
issue with cache and tlb flushing.

Use the routine adjust_range_if_pmd_sharing_possible() to calculate worst
case ranges for mmu notifiers.  Ensure that this range is flushed if
huge_pmd_unshare succeeds and unmaps a PUD_SUZE area.

Link: http://lkml.kernel.org/r/20180823205917.16297-3-mike.kravetz@oracle.com
Signed-off-by: Mike Kravetz <mike.kravetz@oracle.com>
Acked-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Reviewed-by: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com>
Cc: Vlastimil Babka <vbabka@suse.cz>
Cc: Davidlohr Bueso <dave@stgolabs.net>
Cc: Michal Hocko <mhocko@kernel.org>
Cc: Jerome Glisse <jglisse@redhat.com>
Cc: Mike Kravetz <mike.kravetz@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-10-05 16:32:04 -07:00
Mike Kravetz 017b1660df mm: migration: fix migration of huge PMD shared pages
The page migration code employs try_to_unmap() to try and unmap the source
page.  This is accomplished by using rmap_walk to find all vmas where the
page is mapped.  This search stops when page mapcount is zero.  For shared
PMD huge pages, the page map count is always 1 no matter the number of
mappings.  Shared mappings are tracked via the reference count of the PMD
page.  Therefore, try_to_unmap stops prematurely and does not completely
unmap all mappings of the source page.

This problem can result is data corruption as writes to the original
source page can happen after contents of the page are copied to the target
page.  Hence, data is lost.

This problem was originally seen as DB corruption of shared global areas
after a huge page was soft offlined due to ECC memory errors.  DB
developers noticed they could reproduce the issue by (hotplug) offlining
memory used to back huge pages.  A simple testcase can reproduce the
problem by creating a shared PMD mapping (note that this must be at least
PUD_SIZE in size and PUD_SIZE aligned (1GB on x86)), and using
migrate_pages() to migrate process pages between nodes while continually
writing to the huge pages being migrated.

To fix, have the try_to_unmap_one routine check for huge PMD sharing by
calling huge_pmd_unshare for hugetlbfs huge pages.  If it is a shared
mapping it will be 'unshared' which removes the page table entry and drops
the reference on the PMD page.  After this, flush caches and TLB.

mmu notifiers are called before locking page tables, but we can not be
sure of PMD sharing until page tables are locked.  Therefore, check for
the possibility of PMD sharing before locking so that notifiers can
prepare for the worst possible case.

Link: http://lkml.kernel.org/r/20180823205917.16297-2-mike.kravetz@oracle.com
[mike.kravetz@oracle.com: make _range_in_vma() a static inline]
  Link: http://lkml.kernel.org/r/6063f215-a5c8-2f0c-465a-2c515ddc952d@oracle.com
Fixes: 39dde65c99 ("shared page table for hugetlb page")
Signed-off-by: Mike Kravetz <mike.kravetz@oracle.com>
Acked-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Reviewed-by: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com>
Acked-by: Michal Hocko <mhocko@suse.com>
Cc: Vlastimil Babka <vbabka@suse.cz>
Cc: Davidlohr Bueso <dave@stgolabs.net>
Cc: Jerome Glisse <jglisse@redhat.com>
Cc: Mike Kravetz <mike.kravetz@oracle.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-10-05 16:32:04 -07:00
Souptick Joarder 2b74030354 mm: Change return type int to vm_fault_t for fault handlers
Use new return type vm_fault_t for fault handler.  For now, this is just
documenting that the function returns a VM_FAULT value rather than an
errno.  Once all instances are converted, vm_fault_t will become a
distinct type.

Ref-> commit 1c8f422059 ("mm: change return type to vm_fault_t")

The aim is to change the return type of finish_fault() and
handle_mm_fault() to vm_fault_t type.  As part of that clean up return
type of all other recursively called functions have been changed to
vm_fault_t type.

The places from where handle_mm_fault() is getting invoked will be
change to vm_fault_t type but in a separate patch.

vmf_error() is the newly introduce inline function in 4.17-rc6.

[akpm@linux-foundation.org: don't shadow outer local `ret' in __do_huge_pmd_anonymous_page()]
Link: http://lkml.kernel.org/r/20180604171727.GA20279@jordon-HP-15-Notebook-PC
Signed-off-by: Souptick Joarder <jrdr.linux@gmail.com>
Reviewed-by: Matthew Wilcox <mawilcox@microsoft.com>
Reviewed-by: Andrew Morton <akpm@linux-foundation.org>
Cc: Matthew Wilcox <willy@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2018-08-23 18:48:44 -07:00
Naoya Horiguchi 6bc9b56433 mm: fix race on soft-offlining free huge pages
Patch series "mm: soft-offline: fix race against page allocation".

Xishi recently reported the issue about race on reusing the target pages
of soft offlining.  Discussion and analysis showed that we need make
sure that setting PG_hwpoison should be done in the right place under
zone->lock for soft offline.  1/2 handles free hugepage's case, and 2/2
hanldes free buddy page's case.

This patch (of 2):

There's a race condition between soft offline and hugetlb_fault which
causes unexpected process killing and/or hugetlb allocation failure.

The process killing is caused by the following flow:

  CPU 0               CPU 1              CPU 2

  soft offline
    get_any_page
    // find the hugetlb is free
                      mmap a hugetlb file
                      page fault
                        ...
                          hugetlb_fault
                            hugetlb_no_page
                              alloc_huge_page
                              // succeed
      soft_offline_free_page
      // set hwpoison flag
                                         mmap the hugetlb file
                                         page fault
                                           ...
                                             hugetlb_fault
                                               hugetlb_no_page
                                                 find_lock_page
                                                   return VM_FAULT_HWPOISON
                                           mm_fault_error
                                             do_sigbus
                                             // kill the process

The hugetlb allocation failure comes from the following flow:

  CPU 0                          CPU 1

                                 mmap a hugetlb file
                                 // reserve all free page but don't fault-in
  soft offline
    get_any_page
    // find the hugetlb is free
      soft_offline_free_page
      // set hwpoison flag
        dissolve_free_huge_page
        // fail because all free hugepages are reserved
                                 page fault
                                   ...
                                     hugetlb_fault
                                       hugetlb_no_page
                                         alloc_huge_page
                                           ...
                                             dequeue_huge_page_node_exact
                                             // ignore hwpoisoned hugepage
                                             // and finally fail due to no-mem

The root cause of this is that current soft-offline code is written based
on an assumption that PageHWPoison flag should be set at first to avoid
accessing the corrupted data.  This makes sense for memory_failure() or
hard offline, but does not for soft offline because soft offline is about
corrected (not uncorrected) error and is safe from data lost.  This patch
changes soft offline semantics where it sets PageHWPoison flag only after
containment of the error page completes successfully.

Link: http://lkml.kernel.org/r/1531452366-11661-2-git-send-email-n-horiguchi@ah.jp.nec.com
Signed-off-by: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com>
Reported-by: Xishi Qiu <xishi.qiuxishi@alibaba-inc.com>
Suggested-by: Xishi Qiu <xishi.qiuxishi@alibaba-inc.com>
Tested-by: Mike Kravetz <mike.kravetz@oracle.com>
Cc: Michal Hocko <mhocko@kernel.org>
Cc: <zy.zhengyi@alibaba-inc.com>
Cc: Mike Kravetz <mike.kravetz@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2018-08-23 18:48:43 -07:00
Cannon Matthews 330d6e489a mm/hugetlb.c: don't zero 1GiB bootmem pages
When using 1GiB pages during early boot, use the new
memblock_virt_alloc_try_nid_raw() to allocate memory without zeroing it.
Zeroing out hundreds or thousands of GiB in a single core memset() call
is very slow, and can make early boot last upwards of 20-30 minutes on
multi TiB machines.

The memory does not need to be zero'd as the hugetlb pages are always
zero'd on page fault.

Tested: Booted with ~3800 1G pages, and it booted successfully in
roughly the same amount of time as with 0, as opposed to the 25+ minutes
it would take before.

Link: http://lkml.kernel.org/r/20180711213313.92481-1-cannonmatthews@google.com
Signed-off-by: Cannon Matthews <cannonmatthews@google.com>
Acked-by: Mike Kravetz <mike.kravetz@oracle.com>
Acked-by: Michal Hocko <mhocko@suse.com>
Cc: Andres Lagar-Cavilla <andreslc@google.com>
Cc: Peter Feiner <pfeiner@google.com>
Cc: David Matlack <dmatlack@google.com>
Cc: Greg Thelen <gthelen@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2018-08-17 16:20:32 -07:00
Mike Kravetz 40d18ebffb mm/hugetlb: remove gigantic page support for HIGHMEM
This reverts ee8f248d26 ("hugetlb: add phys addr to struct
huge_bootmem_page").

At one time powerpc used this field and supporting code.  However that
was removed with commit 79cc38ded1 ("powerpc/mm/hugetlb: Add support
for reserving gigantic huge pages via kernel command line").

There are no users of this field and supporting code, so remove it.

Link: http://lkml.kernel.org/r/20180711195913.1294-1-mike.kravetz@oracle.com
Signed-off-by: Mike Kravetz <mike.kravetz@oracle.com>
Reviewed-by: Andrew Morton <akpm@linux-foundation.org>
Acked-by: Michal Hocko <mhocko@suse.com>
Cc: "Aneesh Kumar K . V" <aneesh.kumar@linux.vnet.ibm.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Cannon Matthews <cannonmatthews@google.com>
Cc: Becky Bruce <beckyb@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2018-08-17 16:20:32 -07:00
Huang Ying 974e6d66b6 mm, hugetlbfs: pass fault address to cow handler
This is to take better advantage of the general huge page copying
optimization.  Where, the target subpage will be copied last to avoid
the cache lines of target subpage to be evicted when copying other
subpages.  This works better if the address of the target subpage is
available when copying huge page.  So hugetlbfs page fault handlers are
changed to pass that information to hugetlb_cow().  This will benefit
workloads which don't access the begin of the hugetlbfs huge page after
the page fault under heavy cache contention.

Link: http://lkml.kernel.org/r/20180524005851.4079-5-ying.huang@intel.com
Signed-off-by: "Huang, Ying" <ying.huang@intel.com>
Reviewed-by: Mike Kravetz <mike.kravetz@oracle.com>
Cc: Michal Hocko <mhocko@suse.com>
Cc: David Rientjes <rientjes@google.com>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: "Kirill A. Shutemov" <kirill.shutemov@linux.intel.com>
Cc: Andi Kleen <andi.kleen@intel.com>
Cc: Jan Kara <jack@suse.cz>
Cc: Matthew Wilcox <willy@infradead.org>
Cc: Hugh Dickins <hughd@google.com>
Cc: Minchan Kim <minchan@kernel.org>
Cc: Shaohua Li <shli@fb.com>
Cc: Christopher Lameter <cl@linux.com>
Cc: "Aneesh Kumar K.V" <aneesh.kumar@linux.vnet.ibm.com>
Cc: Punit Agrawal <punit.agrawal@arm.com>
Cc: Anshuman Khandual <khandual@linux.vnet.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2018-08-17 16:20:29 -07:00
Huang Ying 5b7a1d4060 mm, hugetlbfs: rename address to haddr in hugetlb_cow()
To take better advantage of general huge page copying optimization, the
target subpage address will be passed to hugetlb_cow(), then
copy_user_huge_page().  So we will use both target subpage address and
huge page size aligned address in hugetlb_cow().  To distinguish between
them, "haddr" is used for huge page size aligned address to be
consistent with Transparent Huge Page naming convention.

Now, only huge page size aligned address is used in hugetlb_cow(), so
the "address" is renamed to "haddr" in hugetlb_cow() in this patch.
Next patch will use target subpage address in hugetlb_cow() too.

The patch is just code cleanup without any functionality changes.

Link: http://lkml.kernel.org/r/20180524005851.4079-4-ying.huang@intel.com
Signed-off-by: "Huang, Ying" <ying.huang@intel.com>
Suggested-by: Mike Kravetz <mike.kravetz@oracle.com>
Suggested-by: Michal Hocko <mhocko@suse.com>
Reviewed-by: Mike Kravetz <mike.kravetz@oracle.com>
Cc: David Rientjes <rientjes@google.com>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: "Kirill A. Shutemov" <kirill.shutemov@linux.intel.com>
Cc: Andi Kleen <andi.kleen@intel.com>
Cc: Jan Kara <jack@suse.cz>
Cc: Matthew Wilcox <willy@infradead.org>
Cc: Hugh Dickins <hughd@google.com>
Cc: Minchan Kim <minchan@kernel.org>
Cc: Shaohua Li <shli@fb.com>
Cc: Christopher Lameter <cl@linux.com>
Cc: "Aneesh Kumar K.V" <aneesh.kumar@linux.vnet.ibm.com>
Cc: Punit Agrawal <punit.agrawal@arm.com>
Cc: Anshuman Khandual <khandual@linux.vnet.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2018-08-17 16:20:29 -07:00
Jane Chu eec3636ad1 ipc/shm.c add ->pagesize function to shm_vm_ops
Commit 05ea88608d ("mm, hugetlbfs: introduce ->pagesize() to
vm_operations_struct") adds a new ->pagesize() function to
hugetlb_vm_ops, intended to cover all hugetlbfs backed files.

With System V shared memory model, if "huge page" is specified, the
"shared memory" is backed by hugetlbfs files, but the mappings initiated
via shmget/shmat have their original vm_ops overwritten with shm_vm_ops,
so we need to add a ->pagesize function to shm_vm_ops.  Otherwise,
vma_kernel_pagesize() returns PAGE_SIZE given a hugetlbfs backed vma,
result in below BUG:

  fs/hugetlbfs/inode.c
        443             if (unlikely(page_mapped(page))) {
        444                     BUG_ON(truncate_op);

resulting in

  hugetlbfs: oracle (4592): Using mlock ulimits for SHM_HUGETLB is deprecated
  ------------[ cut here ]------------
  kernel BUG at fs/hugetlbfs/inode.c:444!
  Modules linked in: nfsv3 rpcsec_gss_krb5 nfsv4 ...
  CPU: 35 PID: 5583 Comm: oracle_5583_sbt Not tainted 4.14.35-1829.el7uek.x86_64 #2
  RIP: 0010:remove_inode_hugepages+0x3db/0x3e2
  ....
  Call Trace:
    hugetlbfs_evict_inode+0x1e/0x3e
    evict+0xdb/0x1af
    iput+0x1a2/0x1f7
    dentry_unlink_inode+0xc6/0xf0
    __dentry_kill+0xd8/0x18d
    dput+0x1b5/0x1ed
    __fput+0x18b/0x216
    ____fput+0xe/0x10
    task_work_run+0x90/0xa7
    exit_to_usermode_loop+0xdd/0x116
    do_syscall_64+0x187/0x1ae
    entry_SYSCALL_64_after_hwframe+0x150/0x0

[jane.chu@oracle.com: relocate comment]
  Link: http://lkml.kernel.org/r/20180731044831.26036-1-jane.chu@oracle.com
Link: http://lkml.kernel.org/r/20180727211727.5020-1-jane.chu@oracle.com
Fixes: 05ea88608d ("mm, hugetlbfs: introduce ->pagesize() to vm_operations_struct")
Signed-off-by: Jane Chu <jane.chu@oracle.com>
Suggested-by: Mike Kravetz <mike.kravetz@oracle.com>
Reviewed-by: Mike Kravetz <mike.kravetz@oracle.com>
Acked-by: Davidlohr Bueso <dave@stgolabs.net>
Acked-by: Michal Hocko <mhocko@suse.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Jan Kara <jack@suse.cz>
Cc: Jérôme Glisse <jglisse@redhat.com>
Cc: Manfred Spraul <manfred@colorfullife.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2018-08-02 16:03:40 -07:00
Cannon Matthews 520495fe96 mm: hugetlb: yield when prepping struct pages
When booting with very large numbers of gigantic (i.e.  1G) pages, the
operations in the loop of gather_bootmem_prealloc, and specifically
prep_compound_gigantic_page, takes a very long time, and can cause a
softlockup if enough pages are requested at boot.

For example booting with 3844 1G pages requires prepping
(set_compound_head, init the count) over 1 billion 4K tail pages, which
takes considerable time.

Add a cond_resched() to the outer loop in gather_bootmem_prealloc() to
prevent this lockup.

Tested: Booted with softlockup_panic=1 hugepagesz=1G hugepages=3844 and
no softlockup is reported, and the hugepages are reported as
successfully setup.

Link: http://lkml.kernel.org/r/20180627214447.260804-1-cannonmatthews@google.com
Signed-off-by: Cannon Matthews <cannonmatthews@google.com>
Reviewed-by: Andrew Morton <akpm@linux-foundation.org>
Reviewed-by: Mike Kravetz <mike.kravetz@oracle.com>
Acked-by: Michal Hocko <mhocko@suse.com>
Cc: Andres Lagar-Cavilla <andreslc@google.com>
Cc: Peter Feiner <pfeiner@google.com>
Cc: Greg Thelen <gthelen@google.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2018-07-03 17:32:19 -07:00
Kees Cook 6da2ec5605 treewide: kmalloc() -> kmalloc_array()
The kmalloc() function has a 2-factor argument form, kmalloc_array(). This
patch replaces cases of:

        kmalloc(a * b, gfp)

with:
        kmalloc_array(a * b, gfp)

as well as handling cases of:

        kmalloc(a * b * c, gfp)

with:

        kmalloc(array3_size(a, b, c), gfp)

as it's slightly less ugly than:

        kmalloc_array(array_size(a, b), c, gfp)

This does, however, attempt to ignore constant size factors like:

        kmalloc(4 * 1024, gfp)

though any constants defined via macros get caught up in the conversion.

Any factors with a sizeof() of "unsigned char", "char", and "u8" were
dropped, since they're redundant.

The tools/ directory was manually excluded, since it has its own
implementation of kmalloc().

The Coccinelle script used for this was:

// Fix redundant parens around sizeof().
@@
type TYPE;
expression THING, E;
@@

(
  kmalloc(
-	(sizeof(TYPE)) * E
+	sizeof(TYPE) * E
  , ...)
|
  kmalloc(
-	(sizeof(THING)) * E
+	sizeof(THING) * E
  , ...)
)

// Drop single-byte sizes and redundant parens.
@@
expression COUNT;
typedef u8;
typedef __u8;
@@

(
  kmalloc(
-	sizeof(u8) * (COUNT)
+	COUNT
  , ...)
|
  kmalloc(
-	sizeof(__u8) * (COUNT)
+	COUNT
  , ...)
|
  kmalloc(
-	sizeof(char) * (COUNT)
+	COUNT
  , ...)
|
  kmalloc(
-	sizeof(unsigned char) * (COUNT)
+	COUNT
  , ...)
|
  kmalloc(
-	sizeof(u8) * COUNT
+	COUNT
  , ...)
|
  kmalloc(
-	sizeof(__u8) * COUNT
+	COUNT
  , ...)
|
  kmalloc(
-	sizeof(char) * COUNT
+	COUNT
  , ...)
|
  kmalloc(
-	sizeof(unsigned char) * COUNT
+	COUNT
  , ...)
)

// 2-factor product with sizeof(type/expression) and identifier or constant.
@@
type TYPE;
expression THING;
identifier COUNT_ID;
constant COUNT_CONST;
@@

(
- kmalloc
+ kmalloc_array
  (
-	sizeof(TYPE) * (COUNT_ID)
+	COUNT_ID, sizeof(TYPE)
  , ...)
|
- kmalloc
+ kmalloc_array
  (
-	sizeof(TYPE) * COUNT_ID
+	COUNT_ID, sizeof(TYPE)
  , ...)
|
- kmalloc
+ kmalloc_array
  (
-	sizeof(TYPE) * (COUNT_CONST)
+	COUNT_CONST, sizeof(TYPE)
  , ...)
|
- kmalloc
+ kmalloc_array
  (
-	sizeof(TYPE) * COUNT_CONST
+	COUNT_CONST, sizeof(TYPE)
  , ...)
|
- kmalloc
+ kmalloc_array
  (
-	sizeof(THING) * (COUNT_ID)
+	COUNT_ID, sizeof(THING)
  , ...)
|
- kmalloc
+ kmalloc_array
  (
-	sizeof(THING) * COUNT_ID
+	COUNT_ID, sizeof(THING)
  , ...)
|
- kmalloc
+ kmalloc_array
  (
-	sizeof(THING) * (COUNT_CONST)
+	COUNT_CONST, sizeof(THING)
  , ...)
|
- kmalloc
+ kmalloc_array
  (
-	sizeof(THING) * COUNT_CONST
+	COUNT_CONST, sizeof(THING)
  , ...)
)

// 2-factor product, only identifiers.
@@
identifier SIZE, COUNT;
@@

- kmalloc
+ kmalloc_array
  (
-	SIZE * COUNT
+	COUNT, SIZE
  , ...)

// 3-factor product with 1 sizeof(type) or sizeof(expression), with
// redundant parens removed.
@@
expression THING;
identifier STRIDE, COUNT;
type TYPE;
@@

(
  kmalloc(
-	sizeof(TYPE) * (COUNT) * (STRIDE)
+	array3_size(COUNT, STRIDE, sizeof(TYPE))
  , ...)
|
  kmalloc(
-	sizeof(TYPE) * (COUNT) * STRIDE
+	array3_size(COUNT, STRIDE, sizeof(TYPE))
  , ...)
|
  kmalloc(
-	sizeof(TYPE) * COUNT * (STRIDE)
+	array3_size(COUNT, STRIDE, sizeof(TYPE))
  , ...)
|
  kmalloc(
-	sizeof(TYPE) * COUNT * STRIDE
+	array3_size(COUNT, STRIDE, sizeof(TYPE))
  , ...)
|
  kmalloc(
-	sizeof(THING) * (COUNT) * (STRIDE)
+	array3_size(COUNT, STRIDE, sizeof(THING))
  , ...)
|
  kmalloc(
-	sizeof(THING) * (COUNT) * STRIDE
+	array3_size(COUNT, STRIDE, sizeof(THING))
  , ...)
|
  kmalloc(
-	sizeof(THING) * COUNT * (STRIDE)
+	array3_size(COUNT, STRIDE, sizeof(THING))
  , ...)
|
  kmalloc(
-	sizeof(THING) * COUNT * STRIDE
+	array3_size(COUNT, STRIDE, sizeof(THING))
  , ...)
)

// 3-factor product with 2 sizeof(variable), with redundant parens removed.
@@
expression THING1, THING2;
identifier COUNT;
type TYPE1, TYPE2;
@@

(
  kmalloc(
-	sizeof(TYPE1) * sizeof(TYPE2) * COUNT
+	array3_size(COUNT, sizeof(TYPE1), sizeof(TYPE2))
  , ...)
|
  kmalloc(
-	sizeof(TYPE1) * sizeof(THING2) * (COUNT)
+	array3_size(COUNT, sizeof(TYPE1), sizeof(TYPE2))
  , ...)
|
  kmalloc(
-	sizeof(THING1) * sizeof(THING2) * COUNT
+	array3_size(COUNT, sizeof(THING1), sizeof(THING2))
  , ...)
|
  kmalloc(
-	sizeof(THING1) * sizeof(THING2) * (COUNT)
+	array3_size(COUNT, sizeof(THING1), sizeof(THING2))
  , ...)
|
  kmalloc(
-	sizeof(TYPE1) * sizeof(THING2) * COUNT
+	array3_size(COUNT, sizeof(TYPE1), sizeof(THING2))
  , ...)
|
  kmalloc(
-	sizeof(TYPE1) * sizeof(THING2) * (COUNT)
+	array3_size(COUNT, sizeof(TYPE1), sizeof(THING2))
  , ...)
)

// 3-factor product, only identifiers, with redundant parens removed.
@@
identifier STRIDE, SIZE, COUNT;
@@

(
  kmalloc(
-	(COUNT) * STRIDE * SIZE
+	array3_size(COUNT, STRIDE, SIZE)
  , ...)
|
  kmalloc(
-	COUNT * (STRIDE) * SIZE
+	array3_size(COUNT, STRIDE, SIZE)
  , ...)
|
  kmalloc(
-	COUNT * STRIDE * (SIZE)
+	array3_size(COUNT, STRIDE, SIZE)
  , ...)
|
  kmalloc(
-	(COUNT) * (STRIDE) * SIZE
+	array3_size(COUNT, STRIDE, SIZE)
  , ...)
|
  kmalloc(
-	COUNT * (STRIDE) * (SIZE)
+	array3_size(COUNT, STRIDE, SIZE)
  , ...)
|
  kmalloc(
-	(COUNT) * STRIDE * (SIZE)
+	array3_size(COUNT, STRIDE, SIZE)
  , ...)
|
  kmalloc(
-	(COUNT) * (STRIDE) * (SIZE)
+	array3_size(COUNT, STRIDE, SIZE)
  , ...)
|
  kmalloc(
-	COUNT * STRIDE * SIZE
+	array3_size(COUNT, STRIDE, SIZE)
  , ...)
)

// Any remaining multi-factor products, first at least 3-factor products,
// when they're not all constants...
@@
expression E1, E2, E3;
constant C1, C2, C3;
@@

(
  kmalloc(C1 * C2 * C3, ...)
|
  kmalloc(
-	(E1) * E2 * E3
+	array3_size(E1, E2, E3)
  , ...)
|
  kmalloc(
-	(E1) * (E2) * E3
+	array3_size(E1, E2, E3)
  , ...)
|
  kmalloc(
-	(E1) * (E2) * (E3)
+	array3_size(E1, E2, E3)
  , ...)
|
  kmalloc(
-	E1 * E2 * E3
+	array3_size(E1, E2, E3)
  , ...)
)

// And then all remaining 2 factors products when they're not all constants,
// keeping sizeof() as the second factor argument.
@@
expression THING, E1, E2;
type TYPE;
constant C1, C2, C3;
@@

(
  kmalloc(sizeof(THING) * C2, ...)
|
  kmalloc(sizeof(TYPE) * C2, ...)
|
  kmalloc(C1 * C2 * C3, ...)
|
  kmalloc(C1 * C2, ...)
|
- kmalloc
+ kmalloc_array
  (
-	sizeof(TYPE) * (E2)
+	E2, sizeof(TYPE)
  , ...)
|
- kmalloc
+ kmalloc_array
  (
-	sizeof(TYPE) * E2
+	E2, sizeof(TYPE)
  , ...)
|
- kmalloc
+ kmalloc_array
  (
-	sizeof(THING) * (E2)
+	E2, sizeof(THING)
  , ...)
|
- kmalloc
+ kmalloc_array
  (
-	sizeof(THING) * E2
+	E2, sizeof(THING)
  , ...)
|
- kmalloc
+ kmalloc_array
  (
-	(E1) * E2
+	E1, E2
  , ...)
|
- kmalloc
+ kmalloc_array
  (
-	(E1) * (E2)
+	E1, E2
  , ...)
|
- kmalloc
+ kmalloc_array
  (
-	E1 * E2
+	E1, E2
  , ...)
)

Signed-off-by: Kees Cook <keescook@chromium.org>
2018-06-12 16:19:22 -07:00
Huang Ying 285b8dcaac mm, hugetlbfs: pass fault address to no page handler
This is to take better advantage of general huge page clearing
optimization (commit c79b57e462b5: "mm: hugetlb: clear target sub-page
last when clearing huge page") for hugetlbfs.

In the general optimization patch, the sub-page to access will be
cleared last to avoid the cache lines of to access sub-page to be
evicted when clearing other sub-pages.  This works better if we have the
address of the sub-page to access, that is, the fault address inside the
huge page.  So the hugetlbfs no page fault handler is changed to pass
that information.  This will benefit workloads which don't access the
begin of the hugetlbfs huge page after the page fault under heavy cache
contention for shared last level cache.

The patch is a generic optimization which should benefit quite some
workloads, not for a specific use case.  To demonstrate the performance
benefit of the patch, we tested it with vm-scalability run on hugetlbfs.

With this patch, the throughput increases ~28.1% in vm-scalability
anon-w-seq test case with 88 processes on a 2 socket Xeon E5 2699 v4
system (44 cores, 88 threads).  The test case creates 88 processes, each
process mmaps a big anonymous memory area with MAP_HUGETLB and writes to
it from the end to the begin.  For each process, other processes could
be seen as other workload which generates heavy cache pressure.  At the
same time, the cache miss rate reduced from ~36.3% to ~25.6%, the IPC
(instruction per cycle) increased from 0.3 to 0.37, and the time spent
in user space is reduced ~19.3%.

Link: http://lkml.kernel.org/r/20180517083539.9242-1-ying.huang@intel.com
Signed-off-by: "Huang, Ying" <ying.huang@intel.com>
Reviewed-by: Mike Kravetz <mike.kravetz@oracle.com>
Cc: Michal Hocko <mhocko@suse.com>
Cc: David Rientjes <rientjes@google.com>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: "Kirill A. Shutemov" <kirill.shutemov@linux.intel.com>
Cc: Andi Kleen <andi.kleen@intel.com>
Cc: Jan Kara <jack@suse.cz>
Cc: Matthew Wilcox <mawilcox@microsoft.com>
Cc: Hugh Dickins <hughd@google.com>
Cc: Minchan Kim <minchan@kernel.org>
Cc: Shaohua Li <shli@fb.com>
Cc: Christopher Lameter <cl@linux.com>
Cc: "Aneesh Kumar K.V" <aneesh.kumar@linux.vnet.ibm.com>
Cc: Punit Agrawal <punit.agrawal@arm.com>
Cc: Anshuman Khandual <khandual@linux.vnet.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2018-06-07 17:34:36 -07:00
Souptick Joarder b3ec9f33ac mm: change return type to vm_fault_t
Use new return type vm_fault_t for fault handler in struct
vm_operations_struct.  For now, this is just documenting that the
function returns a VM_FAULT value rather than an errno.  Once all
instances are converted, vm_fault_t will become a distinct type.

See commit 1c8f422059 ("mm: change return type to vm_fault_t")

Link: http://lkml.kernel.org/r/20180512063745.GA26866@jordon-HP-15-Notebook-PC
Signed-off-by: Souptick Joarder <jrdr.linux@gmail.com>
Reviewed-by: Matthew Wilcox <mawilcox@microsoft.com>
Reviewed-by: Andrew Morton <akpm@linux-foundation.org>
Cc: Joe Perches <joe@perches.com>
Cc: Michal Hocko <mhocko@suse.com>
Cc: Hugh Dickins <hughd@google.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: David Rientjes <rientjes@google.com>
Cc: Mike Kravetz <mike.kravetz@oracle.com>
Cc: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com>
Cc: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2018-06-07 17:34:36 -07:00
Jonathan Corbet 24844fd339 Merge branch 'mm-rst' into docs-next
Mike Rapoport says:

  These patches convert files in Documentation/vm to ReST format, add an
  initial index and link it to the top level documentation.

  There are no contents changes in the documentation, except few spelling
  fixes. The relatively large diffstat stems from the indentation and
  paragraph wrapping changes.

  I've tried to keep the formatting as consistent as possible, but I could
  miss some places that needed markup and add some markup where it was not
  necessary.

[jc: significant conflicts in vm/hmm.rst]
2018-04-16 14:25:08 -06:00
Mike Rapoport ad56b738c5 docs/vm: rename documentation files to .rst
Signed-off-by: Mike Rapoport <rppt@linux.vnet.ibm.com>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
2018-04-16 14:18:15 -06:00
Dan Williams 05ea88608d mm, hugetlbfs: introduce ->pagesize() to vm_operations_struct
When device-dax is operating in huge-page mode we want it to behave like
hugetlbfs and report the MMU page mapping size that is being enforced by
the vma.

Similar to commit 31383c6865 "mm, hugetlbfs: introduce ->split() to
vm_operations_struct" it would be messy to teach vma_mmu_pagesize()
about device-dax page mapping sizes in the same (hstate) way that
hugetlbfs communicates this attribute.  Instead, these patches introduce
a new ->pagesize() vm operation.

Link: http://lkml.kernel.org/r/151996254734.27922.15813097401404359642.stgit@dwillia2-desk3.amr.corp.intel.com
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Reported-by: Jane Chu <jane.chu@oracle.com>
Reviewed-by: Andrew Morton <akpm@linux-foundation.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Paul Mackerras <paulus@samba.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2018-04-05 21:36:26 -07:00
Dan Williams 09135cc594 mm, powerpc: use vma_kernel_pagesize() in vma_mmu_pagesize()
Patch series "mm, smaps: MMUPageSize for device-dax", v3.

Similar to commit 31383c6865 ("mm, hugetlbfs: introduce ->split() to
vm_operations_struct") here is another occasion where we want
special-case hugetlbfs/hstate enabling to also apply to device-dax.

This prompts the question what other hstate conversions we might do
beyond ->split() and ->pagesize(), but this appears to be the last of
the usages of hstate_vma() in generic/non-hugetlbfs specific code paths.

This patch (of 3):

The current powerpc definition of vma_mmu_pagesize() open codes looking
up the page size via hstate.  It is identical to the generic
vma_kernel_pagesize() implementation.

Now, vma_kernel_pagesize() is growing support for determining the page
size of Device-DAX vmas in addition to the existing Hugetlbfs page size
determination.

Ideally, if the powerpc vma_mmu_pagesize() used vma_kernel_pagesize() it
would automatically benefit from any new vma-type support that is added
to vma_kernel_pagesize().  However, the powerpc vma_mmu_pagesize() is
prevented from calling vma_kernel_pagesize() due to a circular header
dependency that requires vma_mmu_pagesize() to be defined before
including <linux/hugetlb.h>.

Break this circular dependency by defining the default vma_mmu_pagesize()
as a __weak symbol to be overridden by the powerpc version.

Link: http://lkml.kernel.org/r/151996254179.27922.2213728278535578744.stgit@dwillia2-desk3.amr.corp.intel.com
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Reviewed-by: Andrew Morton <akpm@linux-foundation.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Jane Chu <jane.chu@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2018-04-05 21:36:26 -07:00
Mike Kravetz 63489f8e82 hugetlbfs: check for pgoff value overflow
A vma with vm_pgoff large enough to overflow a loff_t type when
converted to a byte offset can be passed via the remap_file_pages system
call.  The hugetlbfs mmap routine uses the byte offset to calculate
reservations and file size.

A sequence such as:

  mmap(0x20a00000, 0x600000, 0, 0x66033, -1, 0);
  remap_file_pages(0x20a00000, 0x600000, 0, 0x20000000000000, 0);

will result in the following when task exits/file closed,

  kernel BUG at mm/hugetlb.c:749!
  Call Trace:
    hugetlbfs_evict_inode+0x2f/0x40
    evict+0xcb/0x190
    __dentry_kill+0xcb/0x150
    __fput+0x164/0x1e0
    task_work_run+0x84/0xa0
    exit_to_usermode_loop+0x7d/0x80
    do_syscall_64+0x18b/0x190
    entry_SYSCALL_64_after_hwframe+0x3d/0xa2

The overflowed pgoff value causes hugetlbfs to try to set up a mapping
with a negative range (end < start) that leaves invalid state which
causes the BUG.

The previous overflow fix to this code was incomplete and did not take
the remap_file_pages system call into account.

[mike.kravetz@oracle.com: v3]
  Link: http://lkml.kernel.org/r/20180309002726.7248-1-mike.kravetz@oracle.com
[akpm@linux-foundation.org: include mmdebug.h]
[akpm@linux-foundation.org: fix -ve left shift count on sh]
Link: http://lkml.kernel.org/r/20180308210502.15952-1-mike.kravetz@oracle.com
Fixes: 045c7a3f53 ("hugetlbfs: fix offset overflow in hugetlbfs mmap")
Signed-off-by: Mike Kravetz <mike.kravetz@oracle.com>
Reported-by: Nic Losby <blurbdust@gmail.com>
Acked-by: Michal Hocko <mhocko@suse.com>
Cc: "Kirill A . Shutemov" <kirill.shutemov@linux.intel.com>
Cc: Yisheng Xie <xieyisheng1@huawei.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2018-03-22 17:07:01 -07:00
Michal Hocko 4704dea36d hugetlb: fix surplus pages accounting
Dan Rue has noticed that libhugetlbfs test suite fails counter test:

  # mount_point="/mnt/hugetlb/"
  # echo 200 > /proc/sys/vm/nr_hugepages
  # mkdir -p "${mount_point}"
  # mount -t hugetlbfs hugetlbfs "${mount_point}"
  # export LD_LIBRARY_PATH=/root/libhugetlbfs/libhugetlbfs-2.20/obj64
  # /root/libhugetlbfs/libhugetlbfs-2.20/tests/obj64/counters
  Starting testcase "/root/libhugetlbfs/libhugetlbfs-2.20/tests/obj64/counters", pid 3319
  Base pool size: 0
  Clean...
  FAIL    Line 326: Bad HugePages_Total: expected 0, actual 1

The bug was bisected to 0c397daea1 ("mm, hugetlb: further simplify
hugetlb allocation API").

The reason is that alloc_surplus_huge_page() misaccounts per node
surplus pages.  We should increase surplus_huge_pages_node rather than
nr_huge_pages_node which is already handled by alloc_fresh_huge_page.

Link: http://lkml.kernel.org/r/20180221191439.GM2231@dhcp22.suse.cz
Fixes: 0c397daea1 ("mm, hugetlb: further simplify hugetlb allocation API")
Signed-off-by: Michal Hocko <mhocko@suse.com>
Reported-by: Dan Rue <dan.rue@linaro.org>
Tested-by: Dan Rue <dan.rue@linaro.org>
Reviewed-by: Mike Kravetz <mike.kravetz@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2018-03-09 16:40:01 -08:00
Michal Hocko 389c8178d0 hugetlb, mbind: fall back to default policy if vma is NULL
Dan Carpenter has noticed that mbind migration callback (new_page) can
get a NULL vma pointer and choke on it inside alloc_huge_page_vma which
relies on the VMA to get the hstate.  We used to BUG_ON this case but
the BUG_+ON has been removed recently by "hugetlb, mempolicy: fix the
mbind hugetlb migration".

The proper way to handle this is to get the hstate from the migrated
page and rely on huge_node (resp.  get_vma_policy) do the right thing
with null VMA.  We are currently falling back to the default mempolicy
in that case which is in line what THP path is doing here.

Link: http://lkml.kernel.org/r/20180110104712.GR1732@dhcp22.suse.cz
Signed-off-by: Michal Hocko <mhocko@suse.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Cc: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com>
Cc: Mike Kravetz <mike.kravetz@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2018-01-31 17:18:40 -08:00
Michal Hocko ebd6372358 hugetlb, mempolicy: fix the mbind hugetlb migration
do_mbind migration code relies on alloc_huge_page_noerr for hugetlb
pages.  alloc_huge_page_noerr uses alloc_huge_page which is a highlevel
allocation function which has to take care of reserves, overcommit or
hugetlb cgroup accounting.  None of that is really required for the page
migration because the new page is only temporal and either will replace
the original page or it will be dropped.  This is essentially as for
other migration call paths and there shouldn't be any reason to handle
mbind in a special way.

The current implementation is even suboptimal because the migration
might fail just because the hugetlb cgroup limit is reached, or the
overcommit is saturated.

Fix this by making mbind like other hugetlb migration paths.  Add a new
migration helper alloc_huge_page_vma as a wrapper around
alloc_huge_page_nodemask with additional mempolicy handling.

alloc_huge_page_noerr has no more users and it can go.

Link: http://lkml.kernel.org/r/20180103093213.26329-7-mhocko@kernel.org
Signed-off-by: Michal Hocko <mhocko@suse.com>
Reviewed-by: Mike Kravetz <mike.kravetz@oracle.com>
Reviewed-by: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com>
Cc: Andrea Reale <ar@linux.vnet.ibm.com>
Cc: Anshuman Khandual <khandual@linux.vnet.ibm.com>
Cc: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Cc: Vlastimil Babka <vbabka@suse.cz>
Cc: Zi Yan <zi.yan@cs.rutgers.edu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2018-01-31 17:18:40 -08:00
Michal Hocko 0c397daea1 mm, hugetlb: further simplify hugetlb allocation API
Hugetlb allocator has several layer of allocation functions depending
and the purpose of the allocation.  There are two allocators depending
on whether the page can be allocated from the page allocator or we need
a contiguous allocator.  This is currently opencoded in
alloc_fresh_huge_page which is the only path that might allocate giga
pages which require the later allocator.  Create alloc_fresh_huge_page
which hides this implementation detail and use it in all callers which
hardcoded the buddy allocator path (__hugetlb_alloc_buddy_huge_page).
This shouldn't introduce any funtional change because both migration and
surplus allocators exlude giga pages explicitly.

While we are at it let's do some renaming.  The current scheme is not
consistent and overly painfull to read and understand.  Get rid of
prefix underscores from most functions.  There is no real reason to make
names longer.

* alloc_fresh_huge_page is the new layer to abstract underlying
  allocator
* __hugetlb_alloc_buddy_huge_page becomes shorter and neater
  alloc_buddy_huge_page.
* Former alloc_fresh_huge_page becomes alloc_pool_huge_page because we put
  the new page directly to the pool
* alloc_surplus_huge_page can drop the opencoded prep_new_huge_page code
  as it uses alloc_fresh_huge_page now
* others lose their excessive prefix underscores to make names shorter

[dan.carpenter@oracle.com: fix double unlock bug in alloc_surplus_huge_page()]
  Link: http://lkml.kernel.org/r/20180109200559.g3iz5kvbdrz7yydp@mwanda
Link: http://lkml.kernel.org/r/20180103093213.26329-6-mhocko@kernel.org
Signed-off-by: Michal Hocko <mhocko@suse.com>
Reviewed-by: Mike Kravetz <mike.kravetz@oracle.com>
Reviewed-by: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com>
Cc: Andrea Reale <ar@linux.vnet.ibm.com>
Cc: Anshuman Khandual <khandual@linux.vnet.ibm.com>
Cc: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Cc: Vlastimil Babka <vbabka@suse.cz>
Cc: Zi Yan <zi.yan@cs.rutgers.edu>
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2018-01-31 17:18:40 -08:00
Michal Hocko 9980d744a0 mm, hugetlb: get rid of surplus page accounting tricks
alloc_surplus_huge_page increases the pool size and the number of
surplus pages opportunistically to prevent from races with the pool size
change.  See commit d1c3fb1f8f ("hugetlb: introduce
nr_overcommit_hugepages sysctl") for more details.

The resulting code is unnecessarily hairy, cause code duplication and
doesn't allow to share the allocation paths.  Moreover pool size changes
tend to be very seldom so optimizing for them is not really reasonable.
Simplify the code and allow to allocate a fresh surplus page as long as
we are under the overcommit limit and then recheck the condition after
the allocation and drop the new page if the situation has changed.  This
should provide a reasonable guarantee that an abrupt allocation requests
will not go way off the limit.

If we consider races with the pool shrinking and enlarging then we
should be reasonably safe as well.  In the first case we are off by one
in the worst case and the second case should work OK because the page is
not yet visible.  We can waste CPU cycles for the allocation but that
should be acceptable for a relatively rare condition.

Link: http://lkml.kernel.org/r/20180103093213.26329-5-mhocko@kernel.org
Signed-off-by: Michal Hocko <mhocko@suse.com>
Reviewed-by: Mike Kravetz <mike.kravetz@oracle.com>
Reviewed-by: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com>
Cc: Andrea Reale <ar@linux.vnet.ibm.com>
Cc: Anshuman Khandual <khandual@linux.vnet.ibm.com>
Cc: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Cc: Vlastimil Babka <vbabka@suse.cz>
Cc: Zi Yan <zi.yan@cs.rutgers.edu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2018-01-31 17:18:40 -08:00
Michal Hocko ab5ac90aec mm, hugetlb: do not rely on overcommit limit during migration
hugepage migration relies on __alloc_buddy_huge_page to get a new page.
This has 2 main disadvantages.

1) it doesn't allow to migrate any huge page if the pool is used
   completely which is not an exceptional case as the pool is static and
   unused memory is just wasted.

2) it leads to a weird semantic when migration between two numa nodes
   might increase the pool size of the destination NUMA node while the
   page is in use.  The issue is caused by per NUMA node surplus pages
   tracking (see free_huge_page).

Address both issues by changing the way how we allocate and account
pages allocated for migration.  Those should temporal by definition.  So
we mark them that way (we will abuse page flags in the 3rd page) and
update free_huge_page to free such pages to the page allocator.  Page
migration path then just transfers the temporal status from the new page
to the old one which will be freed on the last reference.  The global
surplus count will never change during this path but we still have to be
careful when migrating a per-node suprlus page.  This is now handled in
move_hugetlb_state which is called from the migration path and it copies
the hugetlb specific page state and fixes up the accounting when needed

Rename __alloc_buddy_huge_page to __alloc_surplus_huge_page to better
reflect its purpose.  The new allocation routine for the migration path
is __alloc_migrate_huge_page.

The user visible effect of this patch is that migrated pages are really
temporal and they travel between NUMA nodes as per the migration
request:

Before migration
  /sys/devices/system/node/node0/hugepages/hugepages-2048kB/free_hugepages:0
  /sys/devices/system/node/node0/hugepages/hugepages-2048kB/nr_hugepages:1
  /sys/devices/system/node/node0/hugepages/hugepages-2048kB/surplus_hugepages:0
  /sys/devices/system/node/node1/hugepages/hugepages-2048kB/free_hugepages:0
  /sys/devices/system/node/node1/hugepages/hugepages-2048kB/nr_hugepages:0
  /sys/devices/system/node/node1/hugepages/hugepages-2048kB/surplus_hugepages:0

After
  /sys/devices/system/node/node0/hugepages/hugepages-2048kB/free_hugepages:0
  /sys/devices/system/node/node0/hugepages/hugepages-2048kB/nr_hugepages:0
  /sys/devices/system/node/node0/hugepages/hugepages-2048kB/surplus_hugepages:0
  /sys/devices/system/node/node1/hugepages/hugepages-2048kB/free_hugepages:0
  /sys/devices/system/node/node1/hugepages/hugepages-2048kB/nr_hugepages:1
  /sys/devices/system/node/node1/hugepages/hugepages-2048kB/surplus_hugepages:0

with the previous implementation, both nodes would have nr_hugepages:1
until the page is freed.

Link: http://lkml.kernel.org/r/20180103093213.26329-4-mhocko@kernel.org
Signed-off-by: Michal Hocko <mhocko@suse.com>
Reviewed-by: Mike Kravetz <mike.kravetz@oracle.com>
Reviewed-by: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com>
Cc: Andrea Reale <ar@linux.vnet.ibm.com>
Cc: Anshuman Khandual <khandual@linux.vnet.ibm.com>
Cc: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Cc: Vlastimil Babka <vbabka@suse.cz>
Cc: Zi Yan <zi.yan@cs.rutgers.edu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2018-01-31 17:18:40 -08:00
Michal Hocko d9cc948f6f mm, hugetlb: integrate giga hugetlb more naturally to the allocation path
Gigantic hugetlb pages were ingrown to the hugetlb code as an alien
specie with a lot of special casing.  The allocation path is not an
exception.  Unnecessarily so to be honest.  It is true that the
underlying allocator is different but that is an implementation detail.

This patch unifies the hugetlb allocation path that a prepares fresh
pool pages.  alloc_fresh_gigantic_page basically copies
alloc_fresh_huge_page logic so we can move everything there.  This will
simplify set_max_huge_pages which doesn't have to care about what kind
of huge page we allocate.

Link: http://lkml.kernel.org/r/20180103093213.26329-3-mhocko@kernel.org
Signed-off-by: Michal Hocko <mhocko@suse.com>
Reviewed-by: Mike Kravetz <mike.kravetz@oracle.com>
Reviewed-by: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com>
Cc: Andrea Reale <ar@linux.vnet.ibm.com>
Cc: Anshuman Khandual <khandual@linux.vnet.ibm.com>
Cc: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Cc: Vlastimil Babka <vbabka@suse.cz>
Cc: Zi Yan <zi.yan@cs.rutgers.edu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2018-01-31 17:18:40 -08:00
Michal Hocko af0fb9df78 mm, hugetlb: unify core page allocation accounting and initialization
Patch series "mm, hugetlb: allocation API and migration improvements"

Motivation:

this is a follow up for [3] for the allocation API and [4] for the
hugetlb migration.  It wasn't really easy to split those into two
separate patch series as they share some code.

My primary motivation to touch this code is to make the gigantic pages
migration working.  The giga pages allocation code is just too fragile
and hacked into the hugetlb code now.  This series tries to move giga
pages closer to the first class citizen.  We are not there yet but
having 5 patches is quite a lot already and it will already make the
code much easier to follow.  I will come with other changes on top after
this sees some review.

The first two patches should be trivial to review.  The third patch
changes the way how we migrate huge pages.  Newly allocated pages are a
subject of the overcommit check and they participate surplus accounting
which is quite unfortunate as the changelog explains.  This patch
doesn't change anything wrt.  giga pages.

Patch #4 removes the surplus accounting hack from
__alloc_surplus_huge_page.  I hope I didn't miss anything there and a
deeper review is really due there.

Patch #5 finally unifies allocation paths and giga pages shouldn't be
any special anymore.  There is also some renaming going on as well.

This patch (of 6):

hugetlb allocator has two entry points to the page allocator
 - alloc_fresh_huge_page_node
 - __hugetlb_alloc_buddy_huge_page

The two differ very subtly in two aspects.  The first one doesn't care
about HTLB_BUDDY_* stats and it doesn't initialize the huge page.
prep_new_huge_page is not used because it not only initializes hugetlb
specific stuff but because it also put_page and releases the page to the
hugetlb pool which is not what is required in some contexts.  This makes
things more complicated than necessary.

Simplify things by a) removing the page allocator entry point duplicity
and only keep __hugetlb_alloc_buddy_huge_page and b) make
prep_new_huge_page more reusable by removing the put_page which moves
the page to the allocator pool.  All current callers are updated to call
put_page explicitly.  Later patches will add new callers which won't
need it.

This patch shouldn't introduce any functional change.

Link: http://lkml.kernel.org/r/20180103093213.26329-2-mhocko@kernel.org
Signed-off-by: Michal Hocko <mhocko@suse.com>
Reviewed-by: Mike Kravetz <mike.kravetz@oracle.com>
Reviewed-by: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com>
Cc: Andrea Reale <ar@linux.vnet.ibm.com>
Cc: Anshuman Khandual <khandual@linux.vnet.ibm.com>
Cc: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Cc: Vlastimil Babka <vbabka@suse.cz>
Cc: Zi Yan <zi.yan@cs.rutgers.edu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2018-01-31 17:18:40 -08:00
Michal Hocko d6cb41cc44 mm, hugetlb: remove hugepages_treat_as_movable sysctl
hugepages_treat_as_movable has been introduced by 396faf0303 ("Allow
huge page allocations to use GFP_HIGH_MOVABLE") to allow hugetlb
allocations from ZONE_MOVABLE even when hugetlb pages were not
migrateable.  The purpose of the movable zone was different at the time.
It aimed at reducing memory fragmentation and hugetlb pages being long
lived and large werre not contributing to the fragmentation so it was
acceptable to use the zone back then.

Things have changed though and the primary purpose of the zone became
migratability guarantee.  If we allow non migrateable hugetlb pages to
be in ZONE_MOVABLE memory hotplug might fail to offline the memory.

Remove the knob and only rely on hugepage_migration_supported to allow
movable zones.

Mel said:

: Primarily it was aimed at allowing the hugetlb pool to safely shrink with
: the ability to grow it again.  The use case was for batched jobs, some of
: which needed huge pages and others that did not but didn't want the memory
: useless pinned in the huge pages pool.
:
: I suspect that more users rely on THP than hugetlbfs for flexible use of
: huge pages with fallback options so I think that removing the option
: should be ok.

Link: http://lkml.kernel.org/r/20171003072619.8654-1-mhocko@kernel.org
Signed-off-by: Michal Hocko <mhocko@suse.com>
Reported-by: Alexandru Moise <00moses.alexander00@gmail.com>
Acked-by: Mel Gorman <mgorman@suse.de>
Cc: Alexandru Moise <00moses.alexander00@gmail.com>
Cc: Mike Kravetz <mike.kravetz@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2018-01-31 17:18:37 -08:00
Roman Gushchin fcb2b0c577 mm: show total hugetlb memory consumption in /proc/meminfo
Currently we display some hugepage statistics (total, free, etc) in
/proc/meminfo, but only for default hugepage size (e.g.  2Mb).

If hugepages of different sizes are used (like 2Mb and 1Gb on x86-64),
/proc/meminfo output can be confusing, as non-default sized hugepages
are not reflected at all, and there are no signs that they are existing
and consuming system memory.

To solve this problem, let's display the total amount of memory,
consumed by hugetlb pages of all sized (both free and used).  Let's call
it "Hugetlb", and display size in kB to match generic /proc/meminfo
style.

For example, (1024 2Mb pages and 2 1Gb pages are pre-allocated):
  $ cat /proc/meminfo
  MemTotal:        8168984 kB
  MemFree:         3789276 kB
  <...>
  CmaFree:               0 kB
  HugePages_Total:    1024
  HugePages_Free:     1024
  HugePages_Rsvd:        0
  HugePages_Surp:        0
  Hugepagesize:       2048 kB
  Hugetlb:         4194304 kB
  DirectMap4k:       32632 kB
  DirectMap2M:     4161536 kB
  DirectMap1G:     6291456 kB

Also, this patch updates corresponding docs to reflect Hugetlb entry
meaning and difference between Hugetlb and HugePages_Total * Hugepagesize.

Link: http://lkml.kernel.org/r/20171115231409.12131-1-guro@fb.com
Signed-off-by: Roman Gushchin <guro@fb.com>
Acked-by: Michal Hocko <mhocko@suse.com>
Acked-by: Johannes Weiner <hannes@cmpxchg.org>
Acked-by: David Rientjes <rientjes@google.com>
Cc: Mike Kravetz <mike.kravetz@oracle.com>
Cc: "Aneesh Kumar K.V" <aneesh.kumar@linux.vnet.ibm.com>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: Dave Hansen <dave.hansen@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2018-01-31 17:18:36 -08:00
Kirill A. Shutemov f4f0a3d85b mm/hugetlb: fix NULL-pointer dereference on 5-level paging machine
I made a mistake during converting hugetlb code to 5-level paging: in
huge_pte_alloc() we have to use p4d_alloc(), not p4d_offset().

Otherwise it leads to crash -- NULL-pointer dereference in pud_alloc()
if p4d table is not yet allocated.

It only can happen in 5-level paging mode.  In 4-level paging mode
p4d_offset() always returns pgd, so we are fine.

Link: http://lkml.kernel.org/r/20171122121921.64822-1-kirill.shutemov@linux.intel.com
Fixes: c2febafc67 ("mm: convert generic code to 5-level paging")
Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Acked-by: Vlastimil Babka <vbabka@suse.cz>
Acked-by: Michal Hocko <mhocko@suse.com>
Cc: <stable@vger.kernel.org>	[4.11+]

Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2017-11-29 18:40:43 -08:00
Dan Williams 31383c6865 mm, hugetlbfs: introduce ->split() to vm_operations_struct
Patch series "device-dax: fix unaligned munmap handling"

When device-dax is operating in huge-page mode we want it to behave like
hugetlbfs and fail attempts to split vmas into unaligned ranges.  It
would be messy to teach the munmap path about device-dax alignment
constraints in the same (hstate) way that hugetlbfs communicates this
constraint.  Instead, these patches introduce a new ->split() vm
operation.

This patch (of 2):

The device-dax interface has similar constraints as hugetlbfs in that it
requires the munmap path to unmap in huge page aligned units.  Rather
than add more custom vma handling code in __split_vma() introduce a new
vm operation to perform this vma specific check.

Link: http://lkml.kernel.org/r/151130418135.4029.6783191281930729710.stgit@dwillia2-desk3.amr.corp.intel.com
Fixes: dee4107924 ("/dev/dax, core: file operations and dax-mmap")
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Cc: Jeff Moyer <jmoyer@redhat.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2017-11-29 18:40:42 -08:00
Jérôme Glisse 0f10851ea4 mm/mmu_notifier: avoid double notification when it is useless
This patch only affects users of mmu_notifier->invalidate_range callback
which are device drivers related to ATS/PASID, CAPI, IOMMUv2, SVM ...
and it is an optimization for those users.  Everyone else is unaffected
by it.

When clearing a pte/pmd we are given a choice to notify the event under
the page table lock (notify version of *_clear_flush helpers do call the
mmu_notifier_invalidate_range).  But that notification is not necessary
in all cases.

This patch removes almost all cases where it is useless to have a call
to mmu_notifier_invalidate_range before
mmu_notifier_invalidate_range_end.  It also adds documentation in all
those cases explaining why.

Below is a more in depth analysis of why this is fine to do this:

For secondary TLB (non CPU TLB) like IOMMU TLB or device TLB (when
device use thing like ATS/PASID to get the IOMMU to walk the CPU page
table to access a process virtual address space).  There is only 2 cases
when you need to notify those secondary TLB while holding page table
lock when clearing a pte/pmd:

  A) page backing address is free before mmu_notifier_invalidate_range_end
  B) a page table entry is updated to point to a new page (COW, write fault
     on zero page, __replace_page(), ...)

Case A is obvious you do not want to take the risk for the device to write
to a page that might now be used by something completely different.

Case B is more subtle. For correctness it requires the following sequence
to happen:
  - take page table lock
  - clear page table entry and notify (pmd/pte_huge_clear_flush_notify())
  - set page table entry to point to new page

If clearing the page table entry is not followed by a notify before setting
the new pte/pmd value then you can break memory model like C11 or C++11 for
the device.

Consider the following scenario (device use a feature similar to ATS/
PASID):

Two address addrA and addrB such that |addrA - addrB| >= PAGE_SIZE we
assume they are write protected for COW (other case of B apply too).

[Time N] -----------------------------------------------------------------
CPU-thread-0  {try to write to addrA}
CPU-thread-1  {try to write to addrB}
CPU-thread-2  {}
CPU-thread-3  {}
DEV-thread-0  {read addrA and populate device TLB}
DEV-thread-2  {read addrB and populate device TLB}
[Time N+1] ---------------------------------------------------------------
CPU-thread-0  {COW_step0: {mmu_notifier_invalidate_range_start(addrA)}}
CPU-thread-1  {COW_step0: {mmu_notifier_invalidate_range_start(addrB)}}
CPU-thread-2  {}
CPU-thread-3  {}
DEV-thread-0  {}
DEV-thread-2  {}
[Time N+2] ---------------------------------------------------------------
CPU-thread-0  {COW_step1: {update page table point to new page for addrA}}
CPU-thread-1  {COW_step1: {update page table point to new page for addrB}}
CPU-thread-2  {}
CPU-thread-3  {}
DEV-thread-0  {}
DEV-thread-2  {}
[Time N+3] ---------------------------------------------------------------
CPU-thread-0  {preempted}
CPU-thread-1  {preempted}
CPU-thread-2  {write to addrA which is a write to new page}
CPU-thread-3  {}
DEV-thread-0  {}
DEV-thread-2  {}
[Time N+3] ---------------------------------------------------------------
CPU-thread-0  {preempted}
CPU-thread-1  {preempted}
CPU-thread-2  {}
CPU-thread-3  {write to addrB which is a write to new page}
DEV-thread-0  {}
DEV-thread-2  {}
[Time N+4] ---------------------------------------------------------------
CPU-thread-0  {preempted}
CPU-thread-1  {COW_step3: {mmu_notifier_invalidate_range_end(addrB)}}
CPU-thread-2  {}
CPU-thread-3  {}
DEV-thread-0  {}
DEV-thread-2  {}
[Time N+5] ---------------------------------------------------------------
CPU-thread-0  {preempted}
CPU-thread-1  {}
CPU-thread-2  {}
CPU-thread-3  {}
DEV-thread-0  {read addrA from old page}
DEV-thread-2  {read addrB from new page}

So here because at time N+2 the clear page table entry was not pair with a
notification to invalidate the secondary TLB, the device see the new value
for addrB before seing the new value for addrA.  This break total memory
ordering for the device.

When changing a pte to write protect or to point to a new write protected
page with same content (KSM) it is ok to delay invalidate_range callback
to mmu_notifier_invalidate_range_end() outside the page table lock.  This
is true even if the thread doing page table update is preempted right
after releasing page table lock before calling
mmu_notifier_invalidate_range_end

Thanks to Andrea for thinking of a problematic scenario for COW.

[jglisse@redhat.com: v2]
  Link: http://lkml.kernel.org/r/20171017031003.7481-2-jglisse@redhat.com
Link: http://lkml.kernel.org/r/20170901173011.10745-1-jglisse@redhat.com
Signed-off-by: Jérôme Glisse <jglisse@redhat.com>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: Nadav Amit <nadav.amit@gmail.com>
Cc: Joerg Roedel <jroedel@suse.de>
Cc: Suravee Suthikulpanit <suravee.suthikulpanit@amd.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Alistair Popple <alistair@popple.id.au>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Andrew Donnellan <andrew.donnellan@au1.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2017-11-15 18:21:03 -08:00
Andrea Arcangeli 1e39214713 userfaultfd: hugetlbfs: prevent UFFDIO_COPY to fill beyond the end of i_size
This oops:

  kernel BUG at fs/hugetlbfs/inode.c:484!
  RIP: remove_inode_hugepages+0x3d0/0x410
  Call Trace:
    hugetlbfs_setattr+0xd9/0x130
    notify_change+0x292/0x410
    do_truncate+0x65/0xa0
    do_sys_ftruncate.constprop.3+0x11a/0x180
    SyS_ftruncate+0xe/0x10
    tracesys+0xd9/0xde

was caused by the lack of i_size check in hugetlb_mcopy_atomic_pte.

mmap() can still succeed beyond the end of the i_size after vmtruncate
zapped vmas in those ranges, but the faults must not succeed, and that
includes UFFDIO_COPY.

We could differentiate the retval to userland to represent a SIGBUS like
a page fault would do (vs SIGSEGV), but it doesn't seem very useful and
we'd need to pick a random retval as there's no meaningful syscall
retval that would differentiate from SIGSEGV and SIGBUS, there's just
-EFAULT.

Link: http://lkml.kernel.org/r/20171016223914.2421-2-aarcange@redhat.com
Signed-off-by: Andrea Arcangeli <aarcange@redhat.com>
Reviewed-by: Mike Kravetz <mike.kravetz@oracle.com>
Cc: Mike Rapoport <rppt@linux.vnet.ibm.com>
Cc: "Dr. David Alan Gilbert" <dgilbert@redhat.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2017-11-03 07:39:19 -07:00
Linus Torvalds bac65d9d87 powerpc updates for 4.14
Nothing really major this release, despite quite a lot of activity. Just lots of
 things all over the place.
 
 Some things of note include:
 
  - Access via perf to a new type of PMU (IMC) on Power9, which can count both
    core events as well as nest unit events (Memory controller etc).
 
  - Optimisations to the radix MMU TLB flushing, mostly to avoid unnecessary Page
    Walk Cache (PWC) flushes when the structure of the tree is not changing.
 
  - Reworks/cleanups of do_page_fault() to modernise it and bring it closer to
    other architectures where possible.
 
  - Rework of our page table walking so that THP updates only need to send IPIs
    to CPUs where the affected mm has run, rather than all CPUs.
 
  - The size of our vmalloc area is increased to 56T on 64-bit hash MMU systems.
    This avoids problems with the percpu allocator on systems with very sparse
    NUMA layouts.
 
  - STRICT_KERNEL_RWX support on PPC32.
 
  - A new sched domain topology for Power9, to capture the fact that pairs of
    cores may share an L2 cache.
 
  - Power9 support for VAS, which is a new mechanism for accessing coprocessors,
    and initial support for using it with the NX compression accelerator.
 
  - Major work on the instruction emulation support, adding support for many new
    instructions, and reworking it so it can be used to implement the emulation
    needed to fixup alignment faults.
 
  - Support for guests under PowerVM to use the Power9 XIVE interrupt controller.
 
 And probably that many things again that are almost as interesting, but I had to
 keep the list short. Plus the usual fixes and cleanups as always.
 
 Thanks to:
   Alexey Kardashevskiy, Alistair Popple, Andreas Schwab, Aneesh Kumar K.V, Anju
   T Sudhakar, Arvind Yadav, Balbir Singh, Benjamin Herrenschmidt, Bhumika Goyal,
   Breno Leitao, Bryant G. Ly, Christophe Leroy, Cédric Le Goater, Dan Carpenter,
   Dou Liyang, Frederic Barrat, Gautham R. Shenoy, Geliang Tang, Geoff Levand,
   Hannes Reinecke, Haren Myneni, Ivan Mikhaylov, John Allen, Julia Lawall, LABBE
   Corentin, Laurentiu Tudor, Madhavan Srinivasan, Markus Elfring, Masahiro
   Yamada, Matt Brown, Michael Neuling, Murilo Opsfelder Araujo, Nathan Fontenot,
   Naveen N. Rao, Nicholas Piggin, Oliver O'Halloran, Paul Mackerras, Rashmica
   Gupta, Rob Herring, Rui Teng, Sam Bobroff, Santosh Sivaraj, Scott Wood,
   Shilpasri G Bhat, Sukadev Bhattiprolu, Suraj Jitindar Singh, Tobin C. Harding,
   Victor Aoqui.
 -----BEGIN PGP SIGNATURE-----
 Version: GnuPG v1
 
 iQIcBAABAgAGBQJZr83SAAoJEFHr6jzI4aWA6pUP/3CEaj2bSxNzWIwidqyYjuoS
 O1moEsP0oYH7eBEWVHalYxvo0QPIIAhbFPaFyrOrgtfDH01Szwu9LcCALGb8orC5
 Hg3IY8mpNG3Q1T8wEtTa56Ik4b5ZFty35S5+X9qLNSFoDUqSvGlSsLzhPNN7f2tl
 XFm2hWqd8wXCwDsuVSFBCF61M3SAm+g6NMVNJ+VL2KIDCwBrOZLhKDPRoxLTAuMa
 jjSdjVIozWyXjUrBFi8HVcoOWLxcT1HsNF0tRs51LwY/+Mlj2jAtFtsx+a06HZa6
 f2p/Kcp/MEispSTk064Ap9cC1seXWI18zwZKpCUFqu0Ec2yTAiGdjOWDyYQldIp+
 ttVPSHQ01YrVKwDFTtM9CiA0EET6fVPhWgAPkPfvH5TvtKwGkNdy0b+nQLuWrYip
 BUmOXmjdIG3nujCzA9sv6/uNNhjhj2y+HWwuV7Qo002VFkhgZFL67u2SSUQLpYPj
 PxdkY8pPVq+O+in94oDV3c36dYFF6+g6A6505Vn6eKUm/TLpszRFGkS3bKKA5vtn
 74FR+guV/5RwYJcdZbfm04DgAocl7AfUDxpwRxibt6KtAK2VZKQuw4ugUTgYEd7W
 mL2+AMmPKuajWXAMTHjCZPbUp9gFNyYyBQTFfGVX/XLiM8erKBnGfoa1/KzUJkhr
 fVZLYIO/gzl34PiTIfgD
 =UJtt
 -----END PGP SIGNATURE-----

Merge tag 'powerpc-4.14-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux

Pull powerpc updates from Michael Ellerman:
 "Nothing really major this release, despite quite a lot of activity.
  Just lots of things all over the place.

  Some things of note include:

   - Access via perf to a new type of PMU (IMC) on Power9, which can
     count both core events as well as nest unit events (Memory
     controller etc).

   - Optimisations to the radix MMU TLB flushing, mostly to avoid
     unnecessary Page Walk Cache (PWC) flushes when the structure of the
     tree is not changing.

   - Reworks/cleanups of do_page_fault() to modernise it and bring it
     closer to other architectures where possible.

   - Rework of our page table walking so that THP updates only need to
     send IPIs to CPUs where the affected mm has run, rather than all
     CPUs.

   - The size of our vmalloc area is increased to 56T on 64-bit hash MMU
     systems. This avoids problems with the percpu allocator on systems
     with very sparse NUMA layouts.

   - STRICT_KERNEL_RWX support on PPC32.

   - A new sched domain topology for Power9, to capture the fact that
     pairs of cores may share an L2 cache.

   - Power9 support for VAS, which is a new mechanism for accessing
     coprocessors, and initial support for using it with the NX
     compression accelerator.

   - Major work on the instruction emulation support, adding support for
     many new instructions, and reworking it so it can be used to
     implement the emulation needed to fixup alignment faults.

   - Support for guests under PowerVM to use the Power9 XIVE interrupt
     controller.

  And probably that many things again that are almost as interesting,
  but I had to keep the list short. Plus the usual fixes and cleanups as
  always.

  Thanks to: Alexey Kardashevskiy, Alistair Popple, Andreas Schwab,
  Aneesh Kumar K.V, Anju T Sudhakar, Arvind Yadav, Balbir Singh,
  Benjamin Herrenschmidt, Bhumika Goyal, Breno Leitao, Bryant G. Ly,
  Christophe Leroy, Cédric Le Goater, Dan Carpenter, Dou Liyang,
  Frederic Barrat, Gautham R. Shenoy, Geliang Tang, Geoff Levand, Hannes
  Reinecke, Haren Myneni, Ivan Mikhaylov, John Allen, Julia Lawall,
  LABBE Corentin, Laurentiu Tudor, Madhavan Srinivasan, Markus Elfring,
  Masahiro Yamada, Matt Brown, Michael Neuling, Murilo Opsfelder Araujo,
  Nathan Fontenot, Naveen N. Rao, Nicholas Piggin, Oliver O'Halloran,
  Paul Mackerras, Rashmica Gupta, Rob Herring, Rui Teng, Sam Bobroff,
  Santosh Sivaraj, Scott Wood, Shilpasri G Bhat, Sukadev Bhattiprolu,
  Suraj Jitindar Singh, Tobin C. Harding, Victor Aoqui"

* tag 'powerpc-4.14-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux: (321 commits)
  powerpc/xive: Fix section __init warning
  powerpc: Fix kernel crash in emulation of vector loads and stores
  powerpc/xive: improve debugging macros
  powerpc/xive: add XIVE Exploitation Mode to CAS
  powerpc/xive: introduce H_INT_ESB hcall
  powerpc/xive: add the HW IRQ number under xive_irq_data
  powerpc/xive: introduce xive_esb_write()
  powerpc/xive: rename xive_poke_esb() in xive_esb_read()
  powerpc/xive: guest exploitation of the XIVE interrupt controller
  powerpc/xive: introduce a common routine xive_queue_page_alloc()
  powerpc/sstep: Avoid used uninitialized error
  axonram: Return directly after a failed kzalloc() in axon_ram_probe()
  axonram: Improve a size determination in axon_ram_probe()
  axonram: Delete an error message for a failed memory allocation in axon_ram_probe()
  powerpc/powernv/npu: Move tlb flush before launching ATSD
  powerpc/macintosh: constify wf_sensor_ops structures
  powerpc/iommu: Use permission-specific DEVICE_ATTR variants
  powerpc/eeh: Delete an error out of memory message at init time
  powerpc/mm: Use seq_putc() in two functions
  macintosh: Convert to using %pOF instead of full_name
  ...
2017-09-07 10:15:40 -07:00
Michal Hocko 79b63f12ab mm, hugetlb: do not allocate non-migrateable gigantic pages from movable zones
alloc_gigantic_page doesn't consider movability of the gigantic hugetlb
when scanning eligible ranges for the allocation.  As 1GB hugetlb pages
are not movable currently this can break the movable zone assumption
that all allocations are migrateable and as such break memory hotplug.

Reorganize the code and use the standard zonelist allocations scheme
that we use for standard hugetbl pages.  htlb_alloc_mask will ensure
that only migratable hugetlb pages will ever see a movable zone.

Link: http://lkml.kernel.org/r/20170803083549.21407-1-mhocko@kernel.org
Fixes: 944d9fec8d ("hugetlb: add support for gigantic page allocation at runtime")
Signed-off-by: Michal Hocko <mhocko@suse.com>
Reviewed-by: Mike Kravetz <mike.kravetz@oracle.com>
Cc: Luiz Capitulino <lcapitulino@redhat.com>
Cc: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2017-09-06 17:27:29 -07:00
Arvind Yadav 67e5ed9699 mm/hugetlb.c: constify attribute_group structures
attribute_group are not supposed to change at runtime.  All functions
working with attribute_group provided by <linux/sysfs.h> work with const
attribute_group.  So mark the non-const structs as const.

Link: http://lkml.kernel.org/r/1501157260-3922-1-git-send-email-arvind.yadav.cs@gmail.com
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2017-09-06 17:27:27 -07:00
Punit Agrawal 9b19df292c mm/hugetlb.c: make huge_pte_offset() consistent and document behaviour
When walking the page tables to resolve an address that points to
!p*d_present() entry, huge_pte_offset() returns inconsistent values
depending on the level of page table (PUD or PMD).

It returns NULL in the case of a PUD entry while in the case of a PMD
entry, it returns a pointer to the page table entry.

A similar inconsitency exists when handling swap entries - returns NULL
for a PUD entry while a pointer to the pte_t is retured for the PMD
entry.

Update huge_pte_offset() to make the behaviour consistent - return a
pointer to the pte_t for hugepage or swap entries.  Only return NULL in
instances where we have a p*d_none() entry and the size parameter
doesn't match the hugepage size at this level of the page table.

Document the behaviour to clarify the expected behaviour of this
function.  This is to set clear semantics for architecture specific
implementations of huge_pte_offset().

Discussions on the arm64 implementation of huge_pte_offset()
(http://www.spinics.net/lists/linux-mm/msg133699.html) showed that there
is benefit from returning a pte_t* in the case of p*d_none().

The fault handling code in hugetlb_fault() can handle p*d_none() entries
and saves an extra round trip to huge_pte_alloc().  Other callers of
huge_pte_offset() should be ok as well.

[punit.agrawal@arm.com: v2]
Link: http://lkml.kernel.org/r/20170725154114.24131-2-punit.agrawal@arm.com
Signed-off-by: Punit Agrawal <punit.agrawal@arm.com>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Reviewed-by: Mike Kravetz <mike.kravetz@oracle.com>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Michal Hocko <mhocko@suse.com>
Cc: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com>
Cc: Steve Capper <steve.capper@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2017-09-06 17:27:26 -07:00
Aneesh Kumar K.V e24a1307ba mm/hugetlb: Allow arch to override and call the weak function
When running in guest mode ppc64 supports a different mechanism for hugetlb
allocation/reservation. The LPAR management application called HMC can
be used to reserve a set of hugepages and we pass the details of
reserved pages via device tree to the guest. (more details in
htab_dt_scan_hugepage_blocks()) . We do the memblock_reserve of the range
and later in the boot sequence, we add the reserved range to huge_boot_pages.

But to enable 16G hugetlb on baremetal config (when we are not running as guest)
we want to do memblock reservation during boot. Generic code already does this

Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
2017-08-15 23:20:30 +10:00
Andrea Arcangeli 5af10dfd0a userfaultfd: hugetlbfs: remove superfluous page unlock in VM_SHARED case
huge_add_to_page_cache->add_to_page_cache implicitly unlocks the page
before returning in case of errors.

The error returned was -EEXIST by running UFFDIO_COPY on a non-hole
offset of a VM_SHARED hugetlbfs mapping.  It was an userland bug that
triggered it and the kernel must cope with it returning -EEXIST from
ioctl(UFFDIO_COPY) as expected.

  page dumped because: VM_BUG_ON_PAGE(!PageLocked(page))
  kernel BUG at mm/filemap.c:964!
  invalid opcode: 0000 [#1] SMP
  CPU: 1 PID: 22582 Comm: qemu-system-x86 Not tainted 4.11.11-300.fc26.x86_64 #1
  RIP: unlock_page+0x4a/0x50
  Call Trace:
    hugetlb_mcopy_atomic_pte+0xc0/0x320
    mcopy_atomic+0x96f/0xbe0
    userfaultfd_ioctl+0x218/0xe90
    do_vfs_ioctl+0xa5/0x600
    SyS_ioctl+0x79/0x90
    entry_SYSCALL_64_fastpath+0x1a/0xa9

Link: http://lkml.kernel.org/r/20170802165145.22628-2-aarcange@redhat.com
Signed-off-by: Andrea Arcangeli <aarcange@redhat.com>
Tested-by: Maxime Coquelin <maxime.coquelin@redhat.com>
Reviewed-by: Mike Kravetz <mike.kravetz@oracle.com>
Cc: "Dr. David Alan Gilbert" <dgilbert@redhat.com>
Cc: Mike Rapoport <rppt@linux.vnet.ibm.com>
Cc: Alexey Perevalov <a.perevalov@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2017-08-10 15:54:06 -07:00
Daniel Jordan 2be7cfed99 mm/hugetlb.c: __get_user_pages ignores certain follow_hugetlb_page errors
Commit 9a291a7c94 ("mm/hugetlb: report -EHWPOISON not -EFAULT when
FOLL_HWPOISON is specified") causes __get_user_pages to ignore certain
errors from follow_hugetlb_page.  After such error, __get_user_pages
subsequently calls faultin_page on the same VMA and start address that
follow_hugetlb_page failed on instead of returning the error immediately
as it should.

In follow_hugetlb_page, when hugetlb_fault returns a value covered under
VM_FAULT_ERROR, follow_hugetlb_page returns it without setting nr_pages
to 0 as __get_user_pages expects in this case, which causes the
following to happen in __get_user_pages: the "while (nr_pages)" check
succeeds, we skip the "if (!vma..." check because we got a VMA the last
time around, we find no page with follow_page_mask, and we call
faultin_page, which calls hugetlb_fault for the second time.

This issue also slightly changes how __get_user_pages works.  Before, it
only returned error if it had made no progress (i = 0).  But now,
follow_hugetlb_page can clobber "i" with an error code since its new
return path doesn't check for progress.  So if "i" is nonzero before a
failing call to follow_hugetlb_page, that indication of progress is lost
and __get_user_pages can return error even if some pages were
successfully pinned.

To fix this, change follow_hugetlb_page so that it updates nr_pages,
allowing __get_user_pages to fail immediately and restoring the "error
only if no progress" behavior to __get_user_pages.

Tested that __get_user_pages returns when expected on error from
hugetlb_fault in follow_hugetlb_page.

Fixes: 9a291a7c94 ("mm/hugetlb: report -EHWPOISON not -EFAULT when FOLL_HWPOISON is specified")
Link: http://lkml.kernel.org/r/1500406795-58462-1-git-send-email-daniel.m.jordan@oracle.com
Signed-off-by: Daniel Jordan <daniel.m.jordan@oracle.com>
Acked-by: Punit Agrawal <punit.agrawal@arm.com>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: "Aneesh Kumar K.V" <aneesh.kumar@linux.vnet.ibm.com>
Cc: Gerald Schaefer <gerald.schaefer@de.ibm.com>
Cc: James Morse <james.morse@arm.com>
Cc: "Kirill A. Shutemov" <kirill.shutemov@linux.intel.com>
Cc: Michal Hocko <mhocko@suse.com>
Cc: Mike Kravetz <mike.kravetz@oracle.com>
Cc: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com>
Cc: zhong jiang <zhongjiang@huawei.com>
Cc: <stable@vger.kernel.org>	[4.12.x]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2017-08-02 16:34:46 -07:00
Michal Hocko dcda9b0471 mm, tree wide: replace __GFP_REPEAT by __GFP_RETRY_MAYFAIL with more useful semantic
__GFP_REPEAT was designed to allow retry-but-eventually-fail semantic to
the page allocator.  This has been true but only for allocations
requests larger than PAGE_ALLOC_COSTLY_ORDER.  It has been always
ignored for smaller sizes.  This is a bit unfortunate because there is
no way to express the same semantic for those requests and they are
considered too important to fail so they might end up looping in the
page allocator for ever, similarly to GFP_NOFAIL requests.

Now that the whole tree has been cleaned up and accidental or misled
usage of __GFP_REPEAT flag has been removed for !costly requests we can
give the original flag a better name and more importantly a more useful
semantic.  Let's rename it to __GFP_RETRY_MAYFAIL which tells the user
that the allocator would try really hard but there is no promise of a
success.  This will work independent of the order and overrides the
default allocator behavior.  Page allocator users have several levels of
guarantee vs.  cost options (take GFP_KERNEL as an example)

 - GFP_KERNEL & ~__GFP_RECLAIM - optimistic allocation without _any_
   attempt to free memory at all. The most light weight mode which even
   doesn't kick the background reclaim. Should be used carefully because
   it might deplete the memory and the next user might hit the more
   aggressive reclaim

 - GFP_KERNEL & ~__GFP_DIRECT_RECLAIM (or GFP_NOWAIT)- optimistic
   allocation without any attempt to free memory from the current
   context but can wake kswapd to reclaim memory if the zone is below
   the low watermark. Can be used from either atomic contexts or when
   the request is a performance optimization and there is another
   fallback for a slow path.

 - (GFP_KERNEL|__GFP_HIGH) & ~__GFP_DIRECT_RECLAIM (aka GFP_ATOMIC) -
   non sleeping allocation with an expensive fallback so it can access
   some portion of memory reserves. Usually used from interrupt/bh
   context with an expensive slow path fallback.

 - GFP_KERNEL - both background and direct reclaim are allowed and the
   _default_ page allocator behavior is used. That means that !costly
   allocation requests are basically nofail but there is no guarantee of
   that behavior so failures have to be checked properly by callers
   (e.g. OOM killer victim is allowed to fail currently).

 - GFP_KERNEL | __GFP_NORETRY - overrides the default allocator behavior
   and all allocation requests fail early rather than cause disruptive
   reclaim (one round of reclaim in this implementation). The OOM killer
   is not invoked.

 - GFP_KERNEL | __GFP_RETRY_MAYFAIL - overrides the default allocator
   behavior and all allocation requests try really hard. The request
   will fail if the reclaim cannot make any progress. The OOM killer
   won't be triggered.

 - GFP_KERNEL | __GFP_NOFAIL - overrides the default allocator behavior
   and all allocation requests will loop endlessly until they succeed.
   This might be really dangerous especially for larger orders.

Existing users of __GFP_REPEAT are changed to __GFP_RETRY_MAYFAIL
because they already had their semantic.  No new users are added.
__alloc_pages_slowpath is changed to bail out for __GFP_RETRY_MAYFAIL if
there is no progress and we have already passed the OOM point.

This means that all the reclaim opportunities have been exhausted except
the most disruptive one (the OOM killer) and a user defined fallback
behavior is more sensible than keep retrying in the page allocator.

[akpm@linux-foundation.org: fix arch/sparc/kernel/mdesc.c]
[mhocko@suse.com: semantic fix]
  Link: http://lkml.kernel.org/r/20170626123847.GM11534@dhcp22.suse.cz
[mhocko@kernel.org: address other thing spotted by Vlastimil]
  Link: http://lkml.kernel.org/r/20170626124233.GN11534@dhcp22.suse.cz
Link: http://lkml.kernel.org/r/20170623085345.11304-3-mhocko@kernel.org
Signed-off-by: Michal Hocko <mhocko@suse.com>
Acked-by: Vlastimil Babka <vbabka@suse.cz>
Cc: Alex Belits <alex.belits@cavium.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Christoph Hellwig <hch@infradead.org>
Cc: Darrick J. Wong <darrick.wong@oracle.com>
Cc: David Daney <david.daney@cavium.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Mel Gorman <mgorman@suse.de>
Cc: NeilBrown <neilb@suse.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2017-07-12 16:26:03 -07:00
Michal Hocko 3e59fcb0e8 hugetlb: add support for preferred node to alloc_huge_page_nodemask
alloc_huge_page_nodemask tries to allocate from any numa node in the
allowed node mask starting from lower numa nodes.  This might lead to
filling up those low NUMA nodes while others are not used.  We can
reduce this risk by introducing a concept of the preferred node similar
to what we have in the regular page allocator.  We will start allocating
from the preferred nid and then iterate over all allowed nodes in the
zonelist order until we try them all.

This is mimicing the page allocator logic except it operates on per-node
mempools.  dequeue_huge_page_vma already does this so distill the
zonelist logic into a more generic dequeue_huge_page_nodemask and use it
in alloc_huge_page_nodemask.

This will allow us to use proper per numa distance fallback also for
alloc_huge_page_node which can use alloc_huge_page_nodemask now and we
can get rid of alloc_huge_page_node helper which doesn't have any user
anymore.

Link: http://lkml.kernel.org/r/20170622193034.28972-3-mhocko@kernel.org
Signed-off-by: Michal Hocko <mhocko@suse.com>
Acked-by: Vlastimil Babka <vbabka@suse.cz>
Reviewed-by: Mike Kravetz <mike.kravetz@oracle.com>
Tested-by: Mike Kravetz <mike.kravetz@oracle.com>
Cc: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com>
Cc: Mel Gorman <mgorman@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2017-07-10 16:32:32 -07:00
Michal Hocko aaf14e40a3 mm, hugetlb: unclutter hugetlb allocation layers
Patch series "mm, hugetlb: allow proper node fallback dequeue".

While working on a hugetlb migration issue addressed in a separate
patchset[1] I have noticed that the hugetlb allocations from the
preallocated pool are quite subotimal.

 [1] //lkml.kernel.org/r/20170608074553.22152-1-mhocko@kernel.org

There is no fallback mechanism implemented and no notion of preferred
node.  I have tried to work around it but Vlastimil was right to push
back for a more robust solution.  It seems that such a solution is to
reuse zonelist approach we use for the page alloctor.

This series has 3 patches.  The first one tries to make hugetlb
allocation layers more clear.  The second one implements the zonelist
hugetlb pool allocation and introduces a preferred node semantic which
is used by the migration callbacks.  The last patch is a clean up.

This patch (of 3):

Hugetlb allocation path for fresh huge pages is unnecessarily complex
and it mixes different interfaces between layers.

__alloc_buddy_huge_page is the central place to perform a new
allocation.  It checks for the hugetlb overcommit and then relies on
__hugetlb_alloc_buddy_huge_page to invoke the page allocator.  This is
all good except that __alloc_buddy_huge_page pushes vma and address down
the callchain and so __hugetlb_alloc_buddy_huge_page has to deal with
two different allocation modes - one for memory policy and other node
specific (or to make it more obscure node non-specific) requests.

This just screams for a reorganization.

This patch pulls out all the vma specific handling up to
__alloc_buddy_huge_page_with_mpol where it belongs.
__alloc_buddy_huge_page will get nodemask argument and
__hugetlb_alloc_buddy_huge_page will become a trivial wrapper over the
page allocator.

In short:
__alloc_buddy_huge_page_with_mpol - memory policy handling
  __alloc_buddy_huge_page - overcommit handling and accounting
    __hugetlb_alloc_buddy_huge_page - page allocator layer

Also note that __hugetlb_alloc_buddy_huge_page and its cpuset retry loop
is not really needed because the page allocator already handles the
cpusets update.

Finally __hugetlb_alloc_buddy_huge_page had a special case for node
specific allocations (when no policy is applied and there is a node
given).  This has relied on __GFP_THISNODE to not fallback to a different
node.  alloc_huge_page_node is the only caller which relies on this
behavior so move the __GFP_THISNODE there.

Not only does this remove quite some code it also should make those
layers easier to follow and clear wrt responsibilities.

Link: http://lkml.kernel.org/r/20170622193034.28972-2-mhocko@kernel.org
Signed-off-by: Michal Hocko <mhocko@suse.com>
Acked-by: Vlastimil Babka <vbabka@suse.cz>
Reviewed-by: Mike Kravetz <mike.kravetz@oracle.com>
Tested-by: Mike Kravetz <mike.kravetz@oracle.com>
Cc: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com>
Cc: Mel Gorman <mgorman@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2017-07-10 16:32:32 -07:00
Matthew Wilcox c6247f72d4 mm/hugetlb.c: replace memfmt with string_get_size
The hugetlb code has its own function to report human-readable sizes.
Convert it to use the shared string_get_size() function.  This will lead
to a minor difference in user visible output (MiB/GiB instead of MB/GB),
but some would argue that's desirable anyway.

Link: http://lkml.kernel.org/r/20170606190350.GA20010@bombadil.infradead.org
Signed-off-by: Matthew Wilcox <mawilcox@microsoft.com>
Cc: Liam R. Howlett <Liam.Howlett@Oracle.com>
Cc: Michal Hocko <mhocko@suse.com>
Cc: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com>
Cc: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Cc: Gerald Schaefer <gerald.schaefer@de.ibm.com>
Cc: zhong jiang <zhongjiang@huawei.com>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2017-07-10 16:32:32 -07:00
David Rientjes 69ed779a14 mm, hugetlb: schedule when potentially allocating many hugepages
A few hugetlb allocators loop while calling the page allocator and can
potentially prevent rescheduling if the page allocator slowpath is not
utilized.

Conditionally schedule when large numbers of hugepages can be allocated.

Anshuman:
 "Fixes a task which was getting hung while writing like 10000 hugepages
  (16MB on POWER8) into /proc/sys/vm/nr_hugepages."

Link: http://lkml.kernel.org/r/alpine.DEB.2.10.1706091535300.66176@chino.kir.corp.google.com
Signed-off-by: David Rientjes <rientjes@google.com>
Reviewed-by: Mike Kravetz <mike.kravetz@oracle.com>
Tested-by: Anshuman Khandual <khandual@linux.vnet.ibm.com>
Cc: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com>
Cc: "Aneesh Kumar K.V" <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2017-07-10 16:32:31 -07:00
Michal Hocko 4db9b2efe9 hugetlb, memory_hotplug: prefer to use reserved pages for migration
new_node_page will try to use the origin's next NUMA node as the
migration destination for hugetlb pages.  If such a node doesn't have
any preallocated pool it falls back to __alloc_buddy_huge_page_no_mpol
to allocate a surplus page instead.  This is quite subotpimal for any
configuration when hugetlb pages are no distributed to all NUMA nodes
evenly.  Say we have a hotplugable node 4 and spare hugetlb pages are
node 0

  /sys/devices/system/node/node0/hugepages/hugepages-2048kB/nr_hugepages:10000
  /sys/devices/system/node/node1/hugepages/hugepages-2048kB/nr_hugepages:0
  /sys/devices/system/node/node2/hugepages/hugepages-2048kB/nr_hugepages:0
  /sys/devices/system/node/node3/hugepages/hugepages-2048kB/nr_hugepages:0
  /sys/devices/system/node/node4/hugepages/hugepages-2048kB/nr_hugepages:10000
  /sys/devices/system/node/node5/hugepages/hugepages-2048kB/nr_hugepages:0
  /sys/devices/system/node/node6/hugepages/hugepages-2048kB/nr_hugepages:0
  /sys/devices/system/node/node7/hugepages/hugepages-2048kB/nr_hugepages:0

Now we consume the whole pool on node 4 and try to offline this node.
All the allocated pages should be moved to node0 which has enough
preallocated pages to hold them.  With the current implementation
offlining very likely fails because hugetlb allocations during runtime
are much less reliable.

Fix this by reusing the nodemask which excludes migration source and try
to find a first node which has a page in the preallocated pool first and
fall back to __alloc_buddy_huge_page_no_mpol only when the whole pool is
consumed.

[akpm@linux-foundation.org: remove bogus arg from alloc_huge_page_nodemask() stub]
Link: http://lkml.kernel.org/r/20170608074553.22152-3-mhocko@kernel.org
Signed-off-by: Michal Hocko <mhocko@suse.com>
Acked-by: Vlastimil Babka <vbabka@suse.cz>
Cc: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com>
Cc: Xishi Qiu <qiuxishi@huawei.com>
Cc: zhong jiang <zhongjiang@huawei.com>
Cc: Joonsoo Kim <js1304@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2017-07-10 16:32:31 -07:00