On x86 the struct pt_regs * grabbed by task_pt_regs() points to an
offset of task->stack. The pt_regs are later dereferenced in
__bpf_get_stack (e.g. by user_mode() check). This can cause a fault if
the task in question exits while bpf_get_task_stack is executing, as
warned by task_stack_page's comment:
* When accessing the stack of a non-current task that might exit, use
* try_get_task_stack() instead. task_stack_page will return a pointer
* that could get freed out from under you.
Taking the comment's advice and using try_get_task_stack() and
put_task_stack() to hold task->stack refcount, or bail early if it's
already 0. Incrementing stack_refcount will ensure the task's stack
sticks around while we're using its data.
I noticed this bug while testing a bpf task iter similar to
bpf_iter_task_stack in selftests, except mine grabbed user stack, and
getting intermittent crashes, which resulted in dumps like:
BUG: unable to handle page fault for address: 0000000000003fe0
\#PF: supervisor read access in kernel mode
\#PF: error_code(0x0000) - not-present page
RIP: 0010:__bpf_get_stack+0xd0/0x230
<snip...>
Call Trace:
bpf_prog_0a2be35c092cb190_get_task_stacks+0x5d/0x3ec
bpf_iter_run_prog+0x24/0x81
__task_seq_show+0x58/0x80
bpf_seq_read+0xf7/0x3d0
vfs_read+0x91/0x140
ksys_read+0x59/0xd0
do_syscall_64+0x48/0x120
entry_SYSCALL_64_after_hwframe+0x44/0xa9
Fixes: fa28dcb82a ("bpf: Introduce helper bpf_get_task_stack()")
Signed-off-by: Dave Marchevsky <davemarchevsky@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Song Liu <songliubraving@fb.com>
Link: https://lore.kernel.org/bpf/20210401000747.3648767-1-davemarchevsky@fb.com
On 32-bit architecture, roundup_pow_of_two() can return 0 when the argument
has upper most bit set due to resulting 1UL << 32. Add a check for this case.
Fixes: d5a3b1f691 ("bpf: introduce BPF_MAP_TYPE_STACK_TRACE")
Signed-off-by: Bui Quang Minh <minhquangbui99@gmail.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Link: https://lore.kernel.org/bpf/20210127063653.3576-1-minhquangbui99@gmail.com
It's possible to have other build id types (other than default SHA1).
Currently there's also ld support for MD5 build id.
Adding size argument to build_id_parse function, that returns (if defined)
size of the parsed build id, so we can recognize the build id type.
Signed-off-by: Jiri Olsa <jolsa@kernel.org>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/20210114134044.1418404-3-jolsa@kernel.org
Moving stack_map_get_build_id into lib with
declaration in linux/buildid.h header:
int build_id_parse(struct vm_area_struct *vma, unsigned char *build_id);
This function returns build id for given struct vm_area_struct.
There is no functional change to stack_map_get_build_id function.
Signed-off-by: Jiri Olsa <jolsa@kernel.org>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Song Liu <songliubraving@fb.com>
Link: https://lore.kernel.org/bpf/20210114134044.1418404-2-jolsa@kernel.org
Core:
- support "prefer busy polling" NAPI operation mode, where we defer softirq
for some time expecting applications to periodically busy poll
- AF_XDP: improve efficiency by more batching and hindering
the adjacency cache prefetcher
- af_packet: make packet_fanout.arr size configurable up to 64K
- tcp: optimize TCP zero copy receive in presence of partial or unaligned
reads making zero copy a performance win for much smaller messages
- XDP: add bulk APIs for returning / freeing frames
- sched: support fragmenting IP packets as they come out of conntrack
- net: allow virtual netdevs to forward UDP L4 and fraglist GSO skbs
BPF:
- BPF switch from crude rlimit-based to memcg-based memory accounting
- BPF type format information for kernel modules and related tracing
enhancements
- BPF implement task local storage for BPF LSM
- allow the FENTRY/FEXIT/RAW_TP tracing programs to use bpf_sk_storage
Protocols:
- mptcp: improve multiple xmit streams support, memory accounting and
many smaller improvements
- TLS: support CHACHA20-POLY1305 cipher
- seg6: add support for SRv6 End.DT4/DT6 behavior
- sctp: Implement RFC 6951: UDP Encapsulation of SCTP
- ppp_generic: add ability to bridge channels directly
- bridge: Connectivity Fault Management (CFM) support as is defined in
IEEE 802.1Q section 12.14.
Drivers:
- mlx5: make use of the new auxiliary bus to organize the driver internals
- mlx5: more accurate port TX timestamping support
- mlxsw:
- improve the efficiency of offloaded next hop updates by using
the new nexthop object API
- support blackhole nexthops
- support IEEE 802.1ad (Q-in-Q) bridging
- rtw88: major bluetooth co-existance improvements
- iwlwifi: support new 6 GHz frequency band
- ath11k: Fast Initial Link Setup (FILS)
- mt7915: dual band concurrent (DBDC) support
- net: ipa: add basic support for IPA v4.5
Refactor:
- a few pieces of in_interrupt() cleanup work from Sebastian Andrzej Siewior
- phy: add support for shared interrupts; get rid of multiple driver
APIs and have the drivers write a full IRQ handler, slight growth
of driver code should be compensated by the simpler API which
also allows shared IRQs
- add common code for handling netdev per-cpu counters
- move TX packet re-allocation from Ethernet switch tag drivers to
a central place
- improve efficiency and rename nla_strlcpy
- number of W=1 warning cleanups as we now catch those in a patchwork
build bot
Old code removal:
- wan: delete the DLCI / SDLA drivers
- wimax: move to staging
- wifi: remove old WDS wifi bridging support
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
-----BEGIN PGP SIGNATURE-----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=GXs1
-----END PGP SIGNATURE-----
Merge tag 'net-next-5.11' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next
Pull networking updates from Jakub Kicinski:
"Core:
- support "prefer busy polling" NAPI operation mode, where we defer
softirq for some time expecting applications to periodically busy
poll
- AF_XDP: improve efficiency by more batching and hindering the
adjacency cache prefetcher
- af_packet: make packet_fanout.arr size configurable up to 64K
- tcp: optimize TCP zero copy receive in presence of partial or
unaligned reads making zero copy a performance win for much smaller
messages
- XDP: add bulk APIs for returning / freeing frames
- sched: support fragmenting IP packets as they come out of conntrack
- net: allow virtual netdevs to forward UDP L4 and fraglist GSO skbs
BPF:
- BPF switch from crude rlimit-based to memcg-based memory accounting
- BPF type format information for kernel modules and related tracing
enhancements
- BPF implement task local storage for BPF LSM
- allow the FENTRY/FEXIT/RAW_TP tracing programs to use
bpf_sk_storage
Protocols:
- mptcp: improve multiple xmit streams support, memory accounting and
many smaller improvements
- TLS: support CHACHA20-POLY1305 cipher
- seg6: add support for SRv6 End.DT4/DT6 behavior
- sctp: Implement RFC 6951: UDP Encapsulation of SCTP
- ppp_generic: add ability to bridge channels directly
- bridge: Connectivity Fault Management (CFM) support as is defined
in IEEE 802.1Q section 12.14.
Drivers:
- mlx5: make use of the new auxiliary bus to organize the driver
internals
- mlx5: more accurate port TX timestamping support
- mlxsw:
- improve the efficiency of offloaded next hop updates by using
the new nexthop object API
- support blackhole nexthops
- support IEEE 802.1ad (Q-in-Q) bridging
- rtw88: major bluetooth co-existance improvements
- iwlwifi: support new 6 GHz frequency band
- ath11k: Fast Initial Link Setup (FILS)
- mt7915: dual band concurrent (DBDC) support
- net: ipa: add basic support for IPA v4.5
Refactor:
- a few pieces of in_interrupt() cleanup work from Sebastian Andrzej
Siewior
- phy: add support for shared interrupts; get rid of multiple driver
APIs and have the drivers write a full IRQ handler, slight growth
of driver code should be compensated by the simpler API which also
allows shared IRQs
- add common code for handling netdev per-cpu counters
- move TX packet re-allocation from Ethernet switch tag drivers to a
central place
- improve efficiency and rename nla_strlcpy
- number of W=1 warning cleanups as we now catch those in a patchwork
build bot
Old code removal:
- wan: delete the DLCI / SDLA drivers
- wimax: move to staging
- wifi: remove old WDS wifi bridging support"
* tag 'net-next-5.11' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (1922 commits)
net: hns3: fix expression that is currently always true
net: fix proc_fs init handling in af_packet and tls
nfc: pn533: convert comma to semicolon
af_vsock: Assign the vsock transport considering the vsock address flags
af_vsock: Set VMADDR_FLAG_TO_HOST flag on the receive path
vsock_addr: Check for supported flag values
vm_sockets: Add VMADDR_FLAG_TO_HOST vsock flag
vm_sockets: Add flags field in the vsock address data structure
net: Disable NETIF_F_HW_TLS_TX when HW_CSUM is disabled
tcp: Add logic to check for SYN w/ data in tcp_simple_retransmit
net: mscc: ocelot: install MAC addresses in .ndo_set_rx_mode from process context
nfc: s3fwrn5: Release the nfc firmware
net: vxget: clean up sparse warnings
mlxsw: spectrum_router: Use eXtended mezzanine to offload IPv4 router
mlxsw: spectrum: Set KVH XLT cache mode for Spectrum2/3
mlxsw: spectrum_router_xm: Introduce basic XM cache flushing
mlxsw: reg: Add Router LPM Cache Enable Register
mlxsw: reg: Add Router LPM Cache ML Delete Register
mlxsw: spectrum_router_xm: Implement L-value tracking for M-index
mlxsw: reg: Add XM Router M Table Register
...
Do not use rlimit-based memory accounting for stackmap maps.
It has been replaced with the memcg-based memory accounting.
Signed-off-by: Roman Gushchin <guro@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Song Liu <songliubraving@fb.com>
Link: https://lore.kernel.org/bpf/20201201215900.3569844-30-guro@fb.com
Get rid of the __call_single_node union and clean up the API a little
to avoid external code relying on the structure layout as much.
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Frederic Weisbecker <frederic@kernel.org>
Function prototypes using ARG_PTR_TO_BTF_ID currently use two ways to signal
which BTF IDs are acceptable. First, bpf_func_proto.btf_id is an array of
IDs, one for each argument. This array is only accessed up to the highest
numbered argument that uses ARG_PTR_TO_BTF_ID and may therefore be less than
five arguments long. It usually points at a BTF_ID_LIST. Second, check_btf_id
is a function pointer that is called by the verifier if present. It gets the
actual BTF ID of the register, and the argument number we're currently checking.
It turns out that the only user check_arg_btf_id ignores the argument, and is
simply used to check whether the BTF ID has a struct sock_common at it's start.
Replace both of these mechanisms with an explicit BTF ID for each argument
in a function proto. Thanks to btf_struct_ids_match this is very flexible:
check_arg_btf_id can be replaced by requiring struct sock_common.
Signed-off-by: Lorenz Bauer <lmb@cloudflare.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Link: https://lore.kernel.org/bpf/20200921121227.255763-5-lmb@cloudflare.com
Some properties of the inner map is used in the verification time.
When an inner map is inserted to an outer map at runtime,
bpf_map_meta_equal() is currently used to ensure those properties
of the inserting inner map stays the same as the verification
time.
In particular, the current bpf_map_meta_equal() checks max_entries which
turns out to be too restrictive for most of the maps which do not use
max_entries during the verification time. It limits the use case that
wants to replace a smaller inner map with a larger inner map. There are
some maps do use max_entries during verification though. For example,
the map_gen_lookup in array_map_ops uses the max_entries to generate
the inline lookup code.
To accommodate differences between maps, the map_meta_equal is added
to bpf_map_ops. Each map-type can decide what to check when its
map is used as an inner map during runtime.
Also, some map types cannot be used as an inner map and they are
currently black listed in bpf_map_meta_alloc() in map_in_map.c.
It is not unusual that the new map types may not aware that such
blacklist exists. This patch enforces an explicit opt-in
and only allows a map to be used as an inner map if it has
implemented the map_meta_equal ops. It is based on the
discussion in [1].
All maps that support inner map has its map_meta_equal points
to bpf_map_meta_equal in this patch. A later patch will
relax the max_entries check for most maps. bpf_types.h
counts 28 map types. This patch adds 23 ".map_meta_equal"
by using coccinelle. -5 for
BPF_MAP_TYPE_PROG_ARRAY
BPF_MAP_TYPE_(PERCPU)_CGROUP_STORAGE
BPF_MAP_TYPE_STRUCT_OPS
BPF_MAP_TYPE_ARRAY_OF_MAPS
BPF_MAP_TYPE_HASH_OF_MAPS
The "if (inner_map->inner_map_meta)" check in bpf_map_meta_alloc()
is moved such that the same error is returned.
[1]: https://lore.kernel.org/bpf/20200522022342.899756-1-kafai@fb.com/
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Link: https://lore.kernel.org/bpf/20200828011806.1970400-1-kafai@fb.com
Currently when we look for build id within bpf_get_stackid helper
call, we check the first NOTE section and we fail if build id is
not there.
However on some system (Fedora) there can be multiple NOTE sections
in binaries and build id data is not always the first one, like:
$ readelf -a /usr/bin/ls
...
[ 2] .note.gnu.propert NOTE 0000000000000338 00000338
0000000000000020 0000000000000000 A 0 0 8358
[ 3] .note.gnu.build-i NOTE 0000000000000358 00000358
0000000000000024 0000000000000000 A 0 0 437c
[ 4] .note.ABI-tag NOTE 000000000000037c 0000037c
...
So the stack_map_get_build_id function will fail on build id retrieval
and fallback to BPF_STACK_BUILD_ID_IP.
This patch is changing the stack_map_get_build_id code to iterate
through all the NOTE sections and try to get build id data from
each of them.
When tracing on sched_switch tracepoint that does bpf_get_stackid
helper call kernel build, I can see about 60% increase of successful
build id retrieval. The rest seems fails on -EFAULT.
Signed-off-by: Jiri Olsa <jolsa@kernel.org>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Song Liu <songliubraving@fb.com>
Link: https://lore.kernel.org/bpf/20200812123102.20032-1-jolsa@kernel.org
Architectures like s390, powerpc, arm64, riscv have speical definition of
bpf_user_pt_regs_t. So we need to cast the pointer before passing it to
bpf_get_stack(). This is similar to bpf_get_stack_tp().
Fixes: 03d42fd2d83f ("bpf: Separate bpf_get_[stack|stackid] for perf events BPF")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Song Liu <songliubraving@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/20200724200503.3629591-1-songliubraving@fb.com
Calling get_perf_callchain() on perf_events from PEBS entries may cause
unwinder errors. To fix this issue, the callchain is fetched early. Such
perf_events are marked with __PERF_SAMPLE_CALLCHAIN_EARLY.
Similarly, calling bpf_get_[stack|stackid] on perf_events from PEBS may
also cause unwinder errors. To fix this, add separate version of these
two helpers, bpf_get_[stack|stackid]_pe. These two hepers use callchain in
bpf_perf_event_data_kern->data->callchain.
Signed-off-by: Song Liu <songliubraving@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/20200723180648.1429892-2-songliubraving@fb.com
Using BTF_ID_LIST macro to define lists for several helpers
using BTF arguments.
And running resolve_btfids on vmlinux elf object during linking,
so the .BTF_ids section gets the IDs resolved.
Signed-off-by: Jiri Olsa <jolsa@kernel.org>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Tested-by: Andrii Nakryiko <andriin@fb.com>
Acked-by: Andrii Nakryiko <andriin@fb.com>
Link: https://lore.kernel.org/bpf/20200711215329.41165-5-jolsa@kernel.org
Without CONFIG_STACKTRACE stack_trace_save_tsk() is not defined. Let
get_callchain_entry_for_task() to always return NULL in such cases.
Fixes: fa28dcb82a ("bpf: Introduce helper bpf_get_task_stack()")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Song Liu <songliubraving@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/20200703024537.79971-1-songliubraving@fb.com
Introduce helper bpf_get_task_stack(), which dumps stack trace of given
task. This is different to bpf_get_stack(), which gets stack track of
current task. One potential use case of bpf_get_task_stack() is to call
it from bpf_iter__task and dump all /proc/<pid>/stack to a seq_file.
bpf_get_task_stack() uses stack_trace_save_tsk() instead of
get_perf_callchain() for kernel stack. The benefit of this choice is that
stack_trace_save_tsk() doesn't require changes in arch/. The downside of
using stack_trace_save_tsk() is that stack_trace_save_tsk() dumps the
stack trace to unsigned long array. For 32-bit systems, we need to
translate it to u64 array.
Signed-off-by: Song Liu <songliubraving@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Andrii Nakryiko <andriin@fb.com>
Link: https://lore.kernel.org/bpf/20200630062846.664389-3-songliubraving@fb.com
bpf_free_used_maps() or close(map_fd) will trigger map_free callback.
bpf_free_used_maps() is called after bpf prog is no longer executing:
bpf_prog_put->call_rcu->bpf_prog_free->bpf_free_used_maps.
Hence there is no need to call synchronize_rcu() to protect map elements.
Note that hash_of_maps and array_of_maps update/delete inner maps via
sys_bpf() that calls maybe_wait_bpf_programs() and synchronize_rcu().
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Andrii Nakryiko <andriin@fb.com>
Acked-by: Paul E. McKenney <paulmck@kernel.org>
Link: https://lore.kernel.org/bpf/20200630043343.53195-2-alexei.starovoitov@gmail.com
Set map_btf_name and map_btf_id for all map types so that map fields can
be accessed by bpf programs.
Signed-off-by: Andrey Ignatov <rdna@fb.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: John Fastabend <john.fastabend@gmail.com>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Link: https://lore.kernel.org/bpf/a825f808f22af52b018dbe82f1c7d29dab5fc978.1592600985.git.rdna@fb.com
Add a couple APIs used by kernel/bpf/stackmap.c only:
- mmap_read_trylock_non_owner()
- mmap_read_unlock_non_owner() (may be called from a work queue).
It's still not ideal that bpf/stackmap subverts the lock ownership in this
way. Thanks to Peter Zijlstra for suggesting this API as the least-ugly
way of addressing this in the short term.
Signed-off-by: Michel Lespinasse <walken@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Reviewed-by: Daniel Jordan <daniel.m.jordan@oracle.com>
Reviewed-by: Vlastimil Babka <vbabka@suse.cz>
Reviewed-by: Davidlohr Bueso <dbueso@suse.de>
Cc: David Rientjes <rientjes@google.com>
Cc: Hugh Dickins <hughd@google.com>
Cc: Jason Gunthorpe <jgg@ziepe.ca>
Cc: Jerome Glisse <jglisse@redhat.com>
Cc: John Hubbard <jhubbard@nvidia.com>
Cc: Laurent Dufour <ldufour@linux.ibm.com>
Cc: Liam Howlett <Liam.Howlett@oracle.com>
Cc: Matthew Wilcox <willy@infradead.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Ying Han <yinghan@google.com>
Link: http://lkml.kernel.org/r/20200520052908.204642-8-walken@google.com
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Implement permissions as stated in uapi/linux/capability.h
In order to do that the verifier allow_ptr_leaks flag is split
into four flags and they are set as:
env->allow_ptr_leaks = bpf_allow_ptr_leaks();
env->bypass_spec_v1 = bpf_bypass_spec_v1();
env->bypass_spec_v4 = bpf_bypass_spec_v4();
env->bpf_capable = bpf_capable();
The first three currently equivalent to perfmon_capable(), since leaking kernel
pointers and reading kernel memory via side channel attacks is roughly
equivalent to reading kernel memory with cap_perfmon.
'bpf_capable' enables bounded loops, precision tracking, bpf to bpf calls and
other verifier features. 'allow_ptr_leaks' enable ptr leaks, ptr conversions,
subtraction of pointers. 'bypass_spec_v1' disables speculative analysis in the
verifier, run time mitigations in bpf array, and enables indirect variable
access in bpf programs. 'bypass_spec_v4' disables emission of sanitation code
by the verifier.
That means that the networking BPF program loaded with CAP_BPF + CAP_NET_ADMIN
will have speculative checks done by the verifier and other spectre mitigation
applied. Such networking BPF program will not be able to leak kernel pointers
and will not be able to access arbitrary kernel memory.
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Link: https://lore.kernel.org/bpf/20200513230355.7858-3-alexei.starovoitov@gmail.com
In a RT kernel down_read_trylock() cannot be used from NMI context and
up_read_non_owner() is another problematic issue.
So in such a configuration, simply elide the annotated stackmap and
just report the raw IPs.
In the longer term, it might be possible to provide a atomic friendly
versions of the page cache traversal which will at least provide the info
if the pages are resident and don't need to be paged in.
[ tglx: Use IS_ENABLED() to avoid the #ifdeffery, fixup the irq work
callback and add a comment ]
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/20200224145644.708960317@linutronix.de
Pull irq updates from Ingo Molnar:
"Most of the IRQ subsystem changes in this cycle were irq-chip driver
updates:
- Qualcomm PDC wakeup interrupt support
- Layerscape external IRQ support
- Broadcom bcm7038 PM and wakeup support
- Ingenic driver cleanup and modernization
- GICv3 ITS preparation for GICv4.1 updates
- GICv4 fixes
There's also the series from Frederic Weisbecker that fixes memory
ordering bugs for the irq-work logic, whose primary fix is to turn
work->irq_work.flags into an atomic variable and then convert the
complex (and buggy) atomic_cmpxchg() loop in irq_work_claim() into a
much simpler atomic_fetch_or() call.
There are also various smaller cleanups"
* 'irq-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (44 commits)
pinctrl/sdm845: Add PDC wakeup interrupt map for GPIOs
pinctrl/msm: Setup GPIO chip in hierarchy
irqchip/qcom-pdc: Add irqchip set/get state calls
irqchip/qcom-pdc: Add irqdomain for wakeup capable GPIOs
irqchip/qcom-pdc: Do not toggle IRQ_ENABLE during mask/unmask
irqchip/qcom-pdc: Update max PDC interrupts
of/irq: Document properties for wakeup interrupt parent
genirq: Introduce irq_chip_get/set_parent_state calls
irqdomain: Add bus token DOMAIN_BUS_WAKEUP
genirq: Fix function documentation of __irq_alloc_descs()
irq_work: Fix IRQ_WORK_BUSY bit clearing
irqchip/ti-sci-inta: Use ERR_CAST inlined function instead of ERR_PTR(PTR_ERR(...))
irq_work: Slightly simplify IRQ_WORK_PENDING clearing
irq_work: Fix irq_work_claim() memory ordering
irq_work: Convert flags to atomic_t
irqchip: Ingenic: Add process for more than one irq at the same time.
irqchip: ingenic: Alloc generic chips from IRQ domain
irqchip: ingenic: Get virq number from IRQ domain
irqchip: ingenic: Error out if IRQ domain creation failed
irqchip: ingenic: Drop redundant irq_suspend / irq_resume functions
...
Pull locking updates from Ingo Molnar:
"The main changes in this cycle were:
- A comprehensive rewrite of the robust/PI futex code's exit handling
to fix various exit races. (Thomas Gleixner et al)
- Rework the generic REFCOUNT_FULL implementation using
atomic_fetch_* operations so that the performance impact of the
cmpxchg() loops is mitigated for common refcount operations.
With these performance improvements the generic implementation of
refcount_t should be good enough for everybody - and this got
confirmed by performance testing, so remove ARCH_HAS_REFCOUNT and
REFCOUNT_FULL entirely, leaving the generic implementation enabled
unconditionally. (Will Deacon)
- Other misc changes, fixes, cleanups"
* 'locking-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (27 commits)
lkdtm: Remove references to CONFIG_REFCOUNT_FULL
locking/refcount: Remove unused 'refcount_error_report()' function
locking/refcount: Consolidate implementations of refcount_t
locking/refcount: Consolidate REFCOUNT_{MAX,SATURATED} definitions
locking/refcount: Move saturation warnings out of line
locking/refcount: Improve performance of generic REFCOUNT_FULL code
locking/refcount: Move the bulk of the REFCOUNT_FULL implementation into the <linux/refcount.h> header
locking/refcount: Remove unused refcount_*_checked() variants
locking/refcount: Ensure integer operands are treated as signed
locking/refcount: Define constants for saturation and max refcount values
futex: Prevent exit livelock
futex: Provide distinct return value when owner is exiting
futex: Add mutex around futex exit
futex: Provide state handling for exec() as well
futex: Sanitize exit state handling
futex: Mark the begin of futex exit explicitly
futex: Set task::futex_state to DEAD right after handling futex exit
futex: Split futex_mm_release() for exit/exec
exit/exec: Seperate mm_release()
futex: Replace PF_EXITPIDONE with a state
...
We need to convert flags to atomic_t in order to later fix an ordering
issue on atomic_cmpxchg() failure. This will allow us to use atomic_fetch_or().
Also clarify the nature of those flags.
[ mingo: Converted two more usage site the original patch missed. ]
Signed-off-by: Frederic Weisbecker <frederic@kernel.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Paul E . McKenney <paulmck@linux.vnet.ibm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: https://lkml.kernel.org/r/20191108160858.31665-2-frederic@kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
bpf stackmap with build-id lookup (BPF_F_STACK_BUILD_ID) can trigger A-A
deadlock on rq_lock():
rcu: INFO: rcu_sched detected stalls on CPUs/tasks:
[...]
Call Trace:
try_to_wake_up+0x1ad/0x590
wake_up_q+0x54/0x80
rwsem_wake+0x8a/0xb0
bpf_get_stack+0x13c/0x150
bpf_prog_fbdaf42eded9fe46_on_event+0x5e3/0x1000
bpf_overflow_handler+0x60/0x100
__perf_event_overflow+0x4f/0xf0
perf_swevent_overflow+0x99/0xc0
___perf_sw_event+0xe7/0x120
__schedule+0x47d/0x620
schedule+0x29/0x90
futex_wait_queue_me+0xb9/0x110
futex_wait+0x139/0x230
do_futex+0x2ac/0xa50
__x64_sys_futex+0x13c/0x180
do_syscall_64+0x42/0x100
entry_SYSCALL_64_after_hwframe+0x44/0xa9
This can be reproduced by:
1. Start a multi-thread program that does parallel mmap() and malloc();
2. taskset the program to 2 CPUs;
3. Attach bpf program to trace_sched_switch and gather stackmap with
build-id, e.g. with trace.py from bcc tools:
trace.py -U -p <pid> -s <some-bin,some-lib> t:sched:sched_switch
A sample reproducer is attached at the end.
This could also trigger deadlock with other locks that are nested with
rq_lock.
Fix this by checking whether irqs are disabled. Since rq_lock and all
other nested locks are irq safe, it is safe to do up_read() when irqs are
not disable. If the irqs are disabled, postpone up_read() in irq_work.
Fixes: 615755a77b ("bpf: extend stackmap to save binary_build_id+offset instead of address")
Signed-off-by: Song Liu <songliubraving@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Alexei Starovoitov <ast@kernel.org>
Cc: Daniel Borkmann <daniel@iogearbox.net>
Link: https://lore.kernel.org/bpf/20191014171223.357174-1-songliubraving@fb.com
Reproducer:
============================ 8< ============================
char *filename;
void *worker(void *p)
{
void *ptr;
int fd;
char *pptr;
fd = open(filename, O_RDONLY);
if (fd < 0)
return NULL;
while (1) {
struct timespec ts = {0, 1000 + rand() % 2000};
ptr = mmap(NULL, 4096 * 64, PROT_READ, MAP_PRIVATE, fd, 0);
usleep(1);
if (ptr == MAP_FAILED) {
printf("failed to mmap\n");
break;
}
munmap(ptr, 4096 * 64);
usleep(1);
pptr = malloc(1);
usleep(1);
pptr[0] = 1;
usleep(1);
free(pptr);
usleep(1);
nanosleep(&ts, NULL);
}
close(fd);
return NULL;
}
int main(int argc, char *argv[])
{
void *ptr;
int i;
pthread_t threads[THREAD_COUNT];
if (argc < 2)
return 0;
filename = argv[1];
for (i = 0; i < THREAD_COUNT; i++) {
if (pthread_create(threads + i, NULL, worker, NULL)) {
fprintf(stderr, "Error creating thread\n");
return 0;
}
}
for (i = 0; i < THREAD_COUNT; i++)
pthread_join(threads[i], NULL);
return 0;
}
============================ 8< ============================
Some ISDN files that got removed in net-next had some changes
done in mainline, take the removals.
Signed-off-by: David S. Miller <davem@davemloft.net>
Most bpf map types doing similar checks and bytes to pages
conversion during memory allocation and charging.
Let's unify these checks by moving them into bpf_map_charge_init().
Signed-off-by: Roman Gushchin <guro@fb.com>
Acked-by: Song Liu <songliubraving@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
In order to unify the existing memlock charging code with the
memcg-based memory accounting, which will be added later, let's
rework the current scheme.
Currently the following design is used:
1) .alloc() callback optionally checks if the allocation will likely
succeed using bpf_map_precharge_memlock()
2) .alloc() performs actual allocations
3) .alloc() callback calculates map cost and sets map.memory.pages
4) map_create() calls bpf_map_init_memlock() which sets map.memory.user
and performs actual charging; in case of failure the map is
destroyed
<map is in use>
1) bpf_map_free_deferred() calls bpf_map_release_memlock(), which
performs uncharge and releases the user
2) .map_free() callback releases the memory
The scheme can be simplified and made more robust:
1) .alloc() calculates map cost and calls bpf_map_charge_init()
2) bpf_map_charge_init() sets map.memory.user and performs actual
charge
3) .alloc() performs actual allocations
<map is in use>
1) .map_free() callback releases the memory
2) bpf_map_charge_finish() performs uncharge and releases the user
The new scheme also allows to reuse bpf_map_charge_init()/finish()
functions for memcg-based accounting. Because charges are performed
before actual allocations and uncharges after freeing the memory,
no bogus memory pressure can be created.
In cases when the map structure is not available (e.g. it's not
created yet, or is already destroyed), on-stack bpf_map_memory
structure is used. The charge can be transferred with the
bpf_map_charge_move() function.
Signed-off-by: Roman Gushchin <guro@fb.com>
Acked-by: Song Liu <songliubraving@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Group "user" and "pages" fields of bpf_map into the bpf_map_memory
structure. Later it can be extended with "memcg" and other related
information.
The main reason for a such change (beside cosmetics) is to pass
bpf_map_memory structure to charging functions before the actual
allocation of bpf_map.
Signed-off-by: Roman Gushchin <guro@fb.com>
Acked-by: Song Liu <songliubraving@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of version 2 of the gnu general public license as
published by the free software foundation
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 107 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Richard Fontana <rfontana@redhat.com>
Reviewed-by: Steve Winslow <swinslow@gmail.com>
Reviewed-by: Alexios Zavras <alexios.zavras@intel.com>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190528171438.615055994@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When returning BPF_STACK_BUILD_ID_IP from stack_map_get_build_id_offset,
make sure that build_id field is empty. Since we are using percpu
free list, there is a possibility that we might reuse some previous
bpf_stack_build_id with non-zero build_id.
Fixes: 615755a77b ("bpf: extend stackmap to save binary_build_id+offset instead of address")
Acked-by: Song Liu <songliubraving@fb.com>
Signed-off-by: Stanislav Fomichev <sdf@google.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Build-id length is not fixed to 20, it can be (`man ld` /--build-id):
* 128-bit (uuid)
* 160-bit (sha1)
* any length specified in ld --build-id=0xhexstring
To fix the issue of missing BPF_STACK_BUILD_ID_VALID for shorter build-ids,
assume that build-id is somewhere in the range of 1 .. 20.
Set the remaining bytes to zero.
v2:
* don't introduce new "len = min(BPF_BUILD_ID_SIZE, nhdr->n_descsz)",
we already know that nhdr->n_descsz <= BPF_BUILD_ID_SIZE if we enter
this 'if' condition
Fixes: 615755a77b ("bpf: extend stackmap to save binary_build_id+offset instead of address")
Acked-by: Song Liu <songliubraving@fb.com>
Signed-off-by: Stanislav Fomichev <sdf@google.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
As Naresh reported, test_stacktrace_build_id() causes panic on i386 and
arm32 systems. This is caused by page_address() returns NULL in certain
cases.
This patch fixes this error by using kmap_atomic/kunmap_atomic instead
of page_address.
Fixes: 615755a77b (" bpf: extend stackmap to save binary_build_id+offset instead of address")
Reported-by: Naresh Kamboju <naresh.kamboju@linaro.org>
Signed-off-by: Song Liu <songliubraving@fb.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
In the following patches queue and stack maps (FIFO and LIFO
datastructures) will be implemented. In order to avoid confusion and
a possible name clash rename stack_map_ops to stack_trace_map_ops
Signed-off-by: Mauricio Vasquez B <mauricio.vasquez@polito.it>
Acked-by: Song Liu <songliubraving@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Commit a26ca7c982 ("bpf: btf: Add pretty print support to
the basic arraymap") and 699c86d6ec ("bpf: btf: add pretty
print for hash/lru_hash maps") enabled support for BTF and
dumping via BPF fs for array and hash/lru map. However, both
can be decoupled from each other such that regular BPF maps
can be supported for attaching BTF key/value information,
while not all maps necessarily need to dump via map_seq_show_elem()
callback.
The basic sanity check which is a prerequisite for all maps
is that key/value size has to match in any case, and some maps
can have extra checks via map_check_btf() callback, e.g.
probing certain types or indicating no support in general. With
that we can also enable retrieving BTF info for per-cpu map
types and lpm.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Yonghong Song <yhs@fb.com>
The stack_map_get_build_id_offset() function is too long for gcc to track
whether 'work' may or may not be initialized at the end of it, leading
to a false-positive warning:
kernel/bpf/stackmap.c: In function 'stack_map_get_build_id_offset':
kernel/bpf/stackmap.c:334:13: error: 'work' may be used uninitialized in this function [-Werror=maybe-uninitialized]
This removes the 'in_nmi_ctx' flag and uses the state of that variable
itself to see if it got initialized.
Fixes: bae77c5eb5 ("bpf: enable stackmap with build_id in nmi context")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Song Liu <songliubraving@fb.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Currently, we cannot parse build_id in nmi context because of
up_read(¤t->mm->mmap_sem), this makes stackmap with build_id
less useful. This patch enables parsing build_id in nmi by putting
the up_read() call in irq_work. To avoid memory allocation in nmi
context, we use per cpu variable for the irq_work. As a result, only
one irq_work per cpu is allowed. If the irq_work is in-use, we
fallback to only report ips.
Cc: Alexei Starovoitov <ast@kernel.org>
Cc: Daniel Borkmann <daniel@iogearbox.net>
Cc: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Song Liu <songliubraving@fb.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Currently, stackmap and bpf_get_stackid helper are provided
for bpf program to get the stack trace. This approach has
a limitation though. If two stack traces have the same hash,
only one will get stored in the stackmap table,
so some stack traces are missing from user perspective.
This patch implements a new helper, bpf_get_stack, will
send stack traces directly to bpf program. The bpf program
is able to see all stack traces, and then can do in-kernel
processing or send stack traces to user space through
shared map or bpf_perf_event_output.
Acked-by: Alexei Starovoitov <ast@fb.com>
Signed-off-by: Yonghong Song <yhs@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
This patch didn't incur functionality change. The function prototype
got changed so that the same function can be reused later.
Signed-off-by: Yonghong Song <yhs@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Currently, bpf stackmap store address for each entry in the call trace.
To map these addresses to user space files, it is necessary to maintain
the mapping from these virtual address to symbols in the binary. Usually,
the user space profiler (such as perf) has to scan /proc/pid/maps at the
beginning of profiling, and monitor mmap2() calls afterwards. Given the
cost of maintaining the address map, this solution is not practical for
system wide profiling that is always on.
This patch tries to solve this problem with a variation of stackmap. This
variation is enabled by flag BPF_F_STACK_BUILD_ID. Instead of storing
addresses, the variation stores ELF file build_id + offset.
Build ID is a 20-byte unique identifier for ELF files. The following
command shows the Build ID of /bin/bash:
[user@]$ readelf -n /bin/bash
...
Build ID: XXXXXXXXXX
...
With BPF_F_STACK_BUILD_ID, bpf_get_stackid() tries to parse Build ID
for each entry in the call trace, and translate it into the following
struct:
struct bpf_stack_build_id_offset {
__s32 status;
unsigned char build_id[BPF_BUILD_ID_SIZE];
union {
__u64 offset;
__u64 ip;
};
};
The search of build_id is limited to the first page of the file, and this
page should be in page cache. Otherwise, we fallback to store ip for this
entry (ip field in struct bpf_stack_build_id_offset). This requires the
build_id to be stored in the first page. A quick survey of binary and
dynamic library files in a few different systems shows that almost all
binary and dynamic library files have build_id in the first page.
Build_id is only meaningful for user stack. If a kernel stack is added to
a stackmap with BPF_F_STACK_BUILD_ID, it will automatically fallback to
only store ip (status == BPF_STACK_BUILD_ID_IP). Similarly, if build_id
lookup failed for some reason, it will also fallback to store ip.
User space can access struct bpf_stack_build_id_offset with bpf
syscall BPF_MAP_LOOKUP_ELEM. It is necessary for user space to
maintain mapping from build id to binary files. This mostly static
mapping is much easier to maintain than per process address maps.
Note: Stackmap with build_id only works in non-nmi context at this time.
This is because we need to take mm->mmap_sem for find_vma(). If this
changes, we would like to allow build_id lookup in nmi context.
Signed-off-by: Song Liu <songliubraving@fb.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
All map types reimplement the field-by-field copy of union bpf_attr
members into struct bpf_map. Add a helper to perform this operation.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Quentin Monnet <quentin.monnet@netronome.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Currently, bpf syscall command BPF_MAP_GET_NEXT_KEY is not
supported for stacktrace map. However, there are use cases where
user space wants to enumerate all stacktrace map entries where
BPF_MAP_GET_NEXT_KEY command will be really helpful.
In addition, if user space wants to delete all map entries
in order to save memory and does not want to close the
map file descriptor, BPF_MAP_GET_NEXT_KEY may help improve
performance if map entries are sparsely populated.
The implementation has similar behavior for
BPF_MAP_GET_NEXT_KEY implementation in hashtab. If user provides
a NULL key pointer or an invalid key, the first key is returned.
Otherwise, the first valid key after the input parameter "key"
is returned, or -ENOENT if no valid key can be found.
Signed-off-by: Yonghong Song <yhs@fb.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Introduce the map read/write flags to the eBPF syscalls that returns the
map fd. The flags is used to set up the file mode when construct a new
file descriptor for bpf maps. To not break the backward capability, the
f_flags is set to O_RDWR if the flag passed by syscall is 0. Otherwise
it should be O_RDONLY or O_WRONLY. When the userspace want to modify or
read the map content, it will check the file mode to see if it is
allowed to make the change.
Signed-off-by: Chenbo Feng <fengc@google.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current map creation API does not allow to provide the numa-node
preference. The memory usually comes from where the map-creation-process
is running. The performance is not ideal if the bpf_prog is known to
always run in a numa node different from the map-creation-process.
One of the use case is sharding on CPU to different LRU maps (i.e.
an array of LRU maps). Here is the test result of map_perf_test on
the INNER_LRU_HASH_PREALLOC test if we force the lru map used by
CPU0 to be allocated from a remote numa node:
[ The machine has 20 cores. CPU0-9 at node 0. CPU10-19 at node 1 ]
># taskset -c 10 ./map_perf_test 512 8 1260000 8000000
5:inner_lru_hash_map_perf pre-alloc 1628380 events per sec
4:inner_lru_hash_map_perf pre-alloc 1626396 events per sec
3:inner_lru_hash_map_perf pre-alloc 1626144 events per sec
6:inner_lru_hash_map_perf pre-alloc 1621657 events per sec
2:inner_lru_hash_map_perf pre-alloc 1621534 events per sec
1:inner_lru_hash_map_perf pre-alloc 1620292 events per sec
7:inner_lru_hash_map_perf pre-alloc 1613305 events per sec
0:inner_lru_hash_map_perf pre-alloc 1239150 events per sec #<<<
After specifying numa node:
># taskset -c 10 ./map_perf_test 512 8 1260000 8000000
5:inner_lru_hash_map_perf pre-alloc 1629627 events per sec
3:inner_lru_hash_map_perf pre-alloc 1628057 events per sec
1:inner_lru_hash_map_perf pre-alloc 1623054 events per sec
6:inner_lru_hash_map_perf pre-alloc 1616033 events per sec
2:inner_lru_hash_map_perf pre-alloc 1614630 events per sec
4:inner_lru_hash_map_perf pre-alloc 1612651 events per sec
7:inner_lru_hash_map_perf pre-alloc 1609337 events per sec
0:inner_lru_hash_map_perf pre-alloc 1619340 events per sec #<<<
This patch adds one field, numa_node, to the bpf_attr. Since numa node 0
is a valid node, a new flag BPF_F_NUMA_NODE is also added. The numa_node
field is honored if and only if the BPF_F_NUMA_NODE flag is set.
Numa node selection is not supported for percpu map.
This patch does not change all the kmalloc. F.e.
'htab = kzalloc()' is not changed since the object
is small enough to stay in the cache.
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
trie_alloc() always needs to have BPF_F_NO_PREALLOC passed in via
attr->map_flags, since it does not support preallocation yet. We
check the flag, but we never copy the flag into trie->map.map_flags,
which is later on exposed into fdinfo and used by loaders such as
iproute2. Latter uses this in bpf_map_selfcheck_pinned() to test
whether a pinned map has the same spec as the one from the BPF obj
file and if not, bails out, which is currently the case for lpm
since it exposes always 0 as flags.
Also copy over flags in array_map_alloc() and stack_map_alloc().
They always have to be 0 right now, but we should make sure to not
miss to copy them over at a later point in time when we add actual
flags for them to use.
Fixes: b95a5c4db0 ("bpf: add a longest prefix match trie map implementation")
Reported-by: Jarno Rajahalme <jarno@covalent.io>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
There's no need to have struct bpf_map_type_list since
it just contains a list_head, the type, and the ops
pointer. Since the types are densely packed and not
actually dynamically registered, it's much easier and
smaller to have an array of type->ops pointer. Also
initialize this array statically to remove code needed
to initialize it.
In order to save duplicating the list, move it to the
types header file added by the previous patch and
include it in the same fashion.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Dave Marchevsky
David S. Miller
Bui Quang Minh
Jiri Olsa
Linus Torvalds
Roman Gushchin
Peter Zijlstra
Lorenz Bauer
Martin KaFai Lau
Song Liu
Alexei Starovoitov
Andrey Ignatov
Michel Lespinasse
Frederic Weisbecker
Qian Cai
Thomas Gleixner
Stanislav Fomichev
Mauricio Vasquez B
Prashant Bhole
Daniel Borkmann
Arnd Bergmann
Yonghong Song
Jakub Kicinski
Chenbo Feng
Johannes Berg